Commit graph

287,159 commits

Author SHA1 Message Date
Hans Verkuil
f7591f1a02 adv7604: fix tx 5v detect regression
commit 0ba4581c84 upstream.

The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:53 -08:00
Robert Jarzmik
7abfb63f28 dmaengine: pxa_dma: fix cyclic transfers
commit f16921275c upstream.

While testing audio with pxa2xx-ac97, underrun were happening while the
user application was correctly feeding the music. Debug proved that the
cyclic transfer is not cyclic, ie. the last descriptor did not loop on
the first.

Another issue is that the descriptor length was always set to 8192,
because of an trivial operator issue.

This was tested on a pxa27x platform.

Fixes: a57e16cf03 ("dmaengine: pxa: add pxa dmaengine driver")
Reported-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:53 -08:00
Gabor Juhos
5667d50cc2 pata-rb532-cf: get rid of the irq_to_gpio() call
commit 018361767a upstream.

The RB532 platform specific irq_to_gpio() implementation has been
removed with commit 832f5dacfa ("MIPS: Remove all the uses of
custom gpio.h"). Now the platform uses the generic stub which causes
the following error:

  pata-rb532-cf pata-rb532-cf: no GPIO found for irq149
  pata-rb532-cf: probe of pata-rb532-cf failed with error -2

Drop the irq_to_gpio() call and get the GPIO number from platform
data instead. After this change, the driver works again:

  scsi host0: pata-rb532-cf
  ata1: PATA max PIO4 irq 149
  ata1.00: CFA: CF 1GB, 20080820, max MWDMA4
  ata1.00: 1989792 sectors, multi 0: LBA
  ata1.00: configured for PIO4
  scsi 0:0:0:0: Direct-Access     ATA      CF 1GB           0820 PQ: 0\
  ANSI: 5
  sd 0:0:0:0: [sda] 1989792 512-byte logical blocks: (1.01 GB/971 MiB)
  sd 0:0:0:0: [sda] Write Protect is off
  sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't\
  support DPO or FUA
   sda: sda1 sda2
  sd 0:0:0:0: [sda] Attached SCSI disk

Fixes: 832f5dacfa ("MIPS: Remove all the uses of custom gpio.h")
Cc: Alban Bedel <albeu@free.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:53 -08:00
Manuel Lauss
a55479ab63 ata: ahci: don't mark HotPlugCapable Ports as external/removable
commit dc8b4afc4a upstream.

The HPCP bit is set by bioses for on-board sata ports either because
they think sata is hotplug capable in general or to allow Windows
to display a "device eject" icon on ports which are routed to an
external connector bracket.

However in Redhat Bugzilla #1310682, users report that with kernel 4.4,
where this bit test first appeared, a lot of partitions on sata drives
are now mounted automatically.

This patch should fix redhat and a lot of other distros which
unconditionally automount all devices which have the "removable"
bit set.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 8a3e33cf92 ("ata: ahci: find eSATA ports and flag them as removable" changes userspace behavior)
Link: http://lkml.kernel.org/g/56CF35FA.1070500@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:52 -08:00
Alexandra Yates
419a2cd1f5 Adding Intel Lewisburg device IDs for SATA
commit f5bdd66c70 upstream.

This patch complements the list of device IDs previously
added for lewisburg sata.

Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:52 -08:00
Arnd Bergmann
b693f2ad0f libata: fix HDIO_GET_32BIT ioctl
commit 287e6611ab upstream.

As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not
work correctly in compat mode with libata.

I have investigated the issue further and found multiple problems
that all appeared with the same commit that originally introduced
HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably
also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy
a 'long' variable containing either 0 or 1 to user space.

The problems with this are:

* On big-endian machines, this will always write a zero because it
  stores the wrong byte into user space.

* In compat mode, the upper three bytes of the variable are updated
  by the compat_hdio_ioctl() function, but they now contain
  uninitialized stack data.

* The hdparm tool calling this ioctl uses a 'static long' variable
  to store the result. This means at least the upper bytes are
  initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT
  would fill them with data that remains stale when the low byte
  is overwritten. Fortunately libata doesn't implement any of the
  affected ioctl commands, so this would only happen when we query
  both an IDE and an ATA device in the same command such as
  "hdparm -N -c /dev/hda /dev/sda"

* The libata code for unknown reasons started using ATA_IOC_GET_IO32
  and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT,
  while the ioctl commands that were added later use the normal
  HDIO_* names. This is harmless but rather confusing.

This addresses all four issues by changing the code to use put_user()
on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem
does, and by clarifying the names of the ioctl commands.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Soohoon Lee <Soohoon.Lee@f5.com>
Tested-by: Soohoon Lee <Soohoon.Lee@f5.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:52 -08:00
Arindam Nath
f17a7e403d drm/amdgpu: return from atombios_dp_get_dpcd only when error
commit 0b39c531cf upstream.

In amdgpu_connector_hotplug(), we need to start DP link
training only after we have received DPCD. The function
amdgpu_atombios_dp_get_dpcd() returns non-zero value only
when an error condition is met, otherwise returns zero.
So in case the function encounters an error, we need to
skip rest of the code and return from amdgpu_connector_hotplug()
immediately. Only when we are successfull in reading DPCD
pin, we should carry on with turning-on the monitor.

Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:52 -08:00
Chunming Zhou
624a59a5d8 drm/amdgpu/gfx8: specify which engine to wait before vm flush
commit 9cac537332 upstream.

Select between me and pfp properly.

Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:51 -08:00
Christian König
a46a700abc drm/amdgpu: apply gfx_v8 fixes to gfx_v7 as well
commit feebe91aa9 upstream.

We never ported that back to CIK, so we could run into VM faults here.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:51 -08:00
Alex Deucher
3b0809af59 drm/amdgpu/pm: update current crtc info after setting the powerstate
commit eda1d1cf8d upstream.

On CI, we need to see if the number of crtcs changes to determine
whether or not we need to upload the mclk table again.  In practice
we don't currently upload the mclk table again after the initial load.
The only reason you would would be to add new states, e.g., for
arbitrary mclk setting which is not currently supported.

Acked-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:51 -08:00
Alex Deucher
80e726c700 drm/radeon/pm: update current crtc info after setting the powerstate
commit 5e031d9fe8 upstream.

On CI, we need to see if the number of crtcs changes to determine
whether or not we need to upload the mclk table again.  In practice
we don't currently upload the mclk table again after the initial load.
The only reason you would would be to add new states, e.g., for
arbitrary mclk setting which is not currently supported.

Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:51 -08:00
Timothy Pearson
598fc9b7d7 drm/ast: Fix incorrect register check for DRAM width
commit 2d02b8bdba upstream.

During DRAM initialization on certain ASpeed devices, an incorrect
bit (bit 10) was checked in the "SDRAM Bus Width Status" register
to determine DRAM width.

Query bit 6 instead in accordance with the Aspeed AST2050 datasheet v1.05.

Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:51 -08:00
Mike Christie
3028963a28 target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors
commit 8a9ebe717a upstream.

In a couple places we are not converting to/from the Linux
block layer 512 bytes sectors.

1.

The request queue values and what we do are a mismatch of
things:

max_discard_sectors - This is in linux block layer 512 byte
sectors. We are just copying this to max_unmap_lba_count.

discard_granularity - This is in bytes. We are converting it
to Linux block layer 512 byte sectors.

discard_alignment - This is in bytes. We are just copying
this over.

The problem is that the core LIO code exports these values in
spc_emulate_evpd_b0 and we use them to test request arguments
in sbc_execute_unmap, but we never convert to the block size
we export to the initiator. If we are not using 512 byte sectors
then we are exporting the wrong values or are checks are off.
And, for the discard_alignment/bytes case we are just plain messed
up.

2.

blkdev_issue_discard's start and number of sector arguments
are supposed to be in linux block layer 512 byte sectors. We are
currently passing in the values we get from the initiator which
might be based on some other sector size.

There is a similar problem in iblock_execute_write_same where
the bio functions want values in 512 byte sectors but we are
passing in what we got from the initiator.

Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ kamal: backport to 4.4-stable: no unmap_zeroes_data ]
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:51 -08:00
Joerg Roedel
00548ecff5 iommu/vt-d: Use BUS_NOTIFY_REMOVED_DEVICE in hotplug path
commit e6a8c9b337 upstream.

In the PCI hotplug path of the Intel IOMMU driver, replace
the usage of the BUS_NOTIFY_DEL_DEVICE notifier, which is
executed before the driver is unbound from the device, with
BUS_NOTIFY_REMOVED_DEVICE, which runs after that.

This fixes a kernel BUG being triggered in the VT-d code
when the device driver tries to unmap DMA buffers and the
VT-d driver already destroyed all mappings.

Reported-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:51 -08:00
Suravee Suthikulpanit
44792d5c90 iommu/amd: Fix boot warning when device 00:00.0 is not iommu covered
commit 38e45d02ea upstream.

The setup code for the performance counters in the AMD IOMMU driver
tests whether the counters can be written. It tests to setup a counter
for device 00:00.0, which fails on systems where this particular device
is not covered by the IOMMU.

Fix this by not relying on device 00:00.0 but only on the IOMMU being
present.

Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:51 -08:00
Jay Cornwall
ad0f9dade9 iommu/amd: Apply workaround for ATS write permission check
commit 358875fd52 upstream.

The AMD Family 15h Models 30h-3Fh (Kaveri) BIOS and Kernel Developer's
Guide omitted part of the BIOS IOMMU L2 register setup specification.
Without this setup the IOMMU L2 does not fully respect write permissions
when handling an ATS translation request.

The IOMMU L2 will set PTE dirty bit when handling an ATS translation with
write permission request, even when PTE RW bit is clear. This may occur by
direct translation (which would cause a PPR) or by prefetch request from
the ATC.

This is observed in practice when the IOMMU L2 modifies a PTE which maps a
pagecache page. The ext4 filesystem driver BUGs when asked to writeback
these (non-modified) pages.

Enable ATS write permission check in the Kaveri IOMMU L2 if BIOS has not.

Signed-off-by: Jay Cornwall <jay@jcornwall.me>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:51 -08:00
Michael S. Tsirkin
7931825da8 vfio: fix ioctl error handling
commit 8160c4e455 upstream.

Calling return copy_to_user(...) in an ioctl will not
do the right thing if there's a pagefault:
copy_to_user returns the number of bytes not copied
in this case.

Fix up vfio to do
	return copy_to_user(...)) ?
		-EFAULT : 0;

everywhere.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:50 -08:00
Jean-Philippe Brucker
2f553b9b6f fbcon: set a default value to blink interval
commit a1e533ec07 upstream.

Since commit 27a4c827c3
	fbcon: use the cursor blink interval provided by vt

two attempts have been made at fixing a possible hang caused by
cursor_timer_handler. That function registers a timer to be triggered at
"jiffies + fbcon_ops.cur_blink_jiffies".

A new case had been encountered during initialisation of clcd-pl11x:

    fbcon_fb_registered
    do_fbcon_takeover

    ->  do_register_con_driver
        fbcon_startup
    (A) add_cursor_timer (with cur_blink_jiffies = 0)

    ->  do_bind_con_driver
        visual_init
        fbcon_init
    (B) cur_blink_jiffies = msecs_to_jiffies(vc->vc_cur_blink_ms);

If we take an softirq anywhere between A and B (and we do),
cursor_timer_handler executes indefinitely.

Instead of patching all possible paths that lead to this case one at a
time, fix the issue at the source and initialise cur_blink_jiffies to
200ms when allocating fbcon_ops. This was its default value before
aforesaid commit. fbcon_cursor or fbcon_init will refine this value
downstream.

Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:50 -08:00
Murali Karicheri
5bbc2b412a PCI: keystone: Fix MSI code that retrieves struct pcie_port pointer
commit 79e3f4a853 upstream.

Commit cbce790059 ("PCI: designware: Make driver arch-agnostic") changed
the host bridge sysdata pointer from the ARM pci_sys_data to the DesignWare
pcie_port structure, and changed pcie-designware.c to reflect that.  But it
did not change the corresponding code in pci-keystone-dw.c, so it caused
crashes on Keystone:

  Unable to handle kernel NULL pointer dereference at virtual address 00000030
  pgd = c0003000
  [00000030] *pgd=80000800004003, *pmd=00000000
  Internal error: Oops: 206 [#1] PREEMPT SMP ARM
  CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.2-00139-gb74f926 #2
  Hardware name: Keystone
  PC is at ks_dw_pcie_msi_irq_unmask+0x24/0x58

Change pci-keystone-dw.c to expect sysdata to be the struct pcie_port
pointer.

[bhelgaas: changelog]
Fixes: cbce790059 ("PCI: designware: Make driver arch-agnostic")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:49 -08:00
Oded Gabbay
3b26135a88 drm/amdgpu: mask out WC from BO on unsupported arches
commit a187f17f0e upstream.

Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:49 -08:00
Geert Uytterhoeven
ad1d8666ae drivers: sh: Restore legacy clock domain on SuperH platforms
commit 0378ba4899 upstream.

CONFIG_ARCH_SHMOBILE is not only enabled for Renesas ARM platforms
(which are DT based and multi-platform), but also on a select set of
Renesas SuperH platforms (SH7722/SH7723/SH7724/SH7343/SH7366). Hence
since commit 0ba58de231 ("drivers: sh: Get rid of
CONFIG_ARCH_SHMOBILE_MULTI"), the legacy clock domain is no longer
installed on these SuperH platforms, and module clocks may not be
enabled when needed, leading to driver failures.

To fix this, add an additional check for CONFIG_OF.

Fixes: 0ba58de231 ("drivers: sh: Get rid of CONFIG_ARCH_SHMOBILE_MULTI").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09 15:34:49 -08:00
Luca Coelho
74e5797640 iwlwifi: mvm: don't allow sched scans without matches to be started
commit 5e56276e75 upstream.

The firmware can perform a scheduled scan with not matchsets passed,
but it can't send notification that results were found.  Since the
userspace then cannot know when we got new results and the firmware
wouldn't trigger a wake in case we are sleeping, it's better not to
allow scans without matchsets.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=110831

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:32 -08:00
Oren Givon
3beb469074 iwlwifi: update and fix 7265 series PCI IDs
commit 006bda75d8 upstream.

Update and fix some 7265 PCI IDs entries.

Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:32 -08:00
Emmanuel Grumbach
8a55831546 iwlwifi: pcie: properly configure the debug buffer size for 8000
commit 62d7476d95 upstream.

8000 device family has a new debug engine that needs to be
configured differently than 7000's.
The debug engine's DMA works in chunks of memory and the
size of the buffer really means the start of the last
chunk. Since one chunk is 256-byte long, we should
configure the device to write to buffer_size - 256.
This fixes a situation were the device would write to
memory it is not allowed to access.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:32 -08:00
Emmanuel Grumbach
d19573e849 iwlwifi: dvm: fix WoWLAN
commit a1cdb1c59c upstream.

My commit below introduced a mutex in the transport to
prevent concurrent operations. To do so, it added a flag
(is_down) to make sure the transport is in the right state.
This uncoverred an bug that didn't cause any harm until
now: iwldvm calls stop_device and then starts the firmware
without calling start_hw in between. While this flow is
fine from the device configuration point of view (register,
etc...), it is now forbidden by the new is_down flag.
This led to this error to appear:
iwlwifi 0000:05:00.0: Can't start_fw since the HW hasn't been started
and the suspend would fail.

This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=109591

Reported-by: Bogdan Bogush <bogdan.s.bogush@gmail.com>
Fixes=fa9f3281cbb1 ("iwlwifi: pcie: lock start_hw / start_fw / stop_device")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:32 -08:00
Matan Barak
9315bf18be IB/cma: Fix RDMA port validation for iWarp
commit 649367735e upstream.

cma_validate_port wrongly assumed that Ethernet devices are RoCE
devices and thus their ndev should be matched in the GID table.
This broke the iWarp support. Fixing that matching the ndev only if
we work on a RoCE port.

Cc: <stable@vger.kernel.org> # 4.4.x-
Fixes: abae1b71dd ('IB/cma: cma_validate_port should verify the port
		     and netdevice')
Reported-by: Hariprasad Shenai <hariprasad@chelsio.com>
Tested-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:32 -08:00
Konrad Rzeszutek Wilk
9108b130f7 xen/pcifront: Fix mysterious crashes when NUMA locality information was extracted.
commit 4d8c8bd6f2 upstream.

Occasionaly PV guests would crash with:

pciback 0000:00:00.1: Xen PCI mapped GSI0 to IRQ16
BUG: unable to handle kernel paging request at 0000000d1a8c0be0
.. snip..
  <ffffffff8139ce1b>] find_next_bit+0xb/0x10
  [<ffffffff81387f22>] cpumask_next_and+0x22/0x40
  [<ffffffff813c1ef8>] pci_device_probe+0xb8/0x120
  [<ffffffff81529097>] ? driver_sysfs_add+0x77/0xa0
  [<ffffffff815293e4>] driver_probe_device+0x1a4/0x2d0
  [<ffffffff813c1ddd>] ? pci_match_device+0xdd/0x110
  [<ffffffff81529657>] __device_attach_driver+0xa7/0xb0
  [<ffffffff815295b0>] ? __driver_attach+0xa0/0xa0
  [<ffffffff81527622>] bus_for_each_drv+0x62/0x90
  [<ffffffff8152978d>] __device_attach+0xbd/0x110
  [<ffffffff815297fb>] device_attach+0xb/0x10
  [<ffffffff813b75ac>] pci_bus_add_device+0x3c/0x70
  [<ffffffff813b7618>] pci_bus_add_devices+0x38/0x80
  [<ffffffff813dc34e>] pcifront_scan_root+0x13e/0x1a0
  [<ffffffff817a0692>] pcifront_backend_changed+0x262/0x60b
  [<ffffffff814644c6>] ? xenbus_gather+0xd6/0x160
  [<ffffffff8120900f>] ? put_object+0x2f/0x50
  [<ffffffff81465c1d>] xenbus_otherend_changed+0x9d/0xa0
  [<ffffffff814678ee>] backend_changed+0xe/0x10
  [<ffffffff81463a28>] xenwatch_thread+0xc8/0x190
  [<ffffffff810f22f0>] ? woken_wake_function+0x10/0x10

which was the result of two things:

When we call pci_scan_root_bus we would pass in 'sd' (sysdata)
pointer which was an 'pcifront_sd' structure. However in the
pci_device_add it expects that the 'sd' is 'struct sysdata' and
sets the dev->node to what is in sd->node (offset 4):

set_dev_node(&dev->dev, pcibus_to_node(bus));

 __pcibus_to_node(const struct pci_bus *bus)
{
        const struct pci_sysdata *sd = bus->sysdata;

        return sd->node;
}

However our structure was pcifront_sd which had nothing at that
offset:

struct pcifront_sd {
        int                        domain;    /*     0     4 */
        /* XXX 4 bytes hole, try to pack */
        struct pcifront_device *   pdev;      /*     8     8 */
}

That is an hole - filled with garbage as we used kmalloc instead of
kzalloc (the second problem).

This patch fixes the issue by:
 1) Use kzalloc to initialize to a well known state.
 2) Put 'struct pci_sysdata' at the start of 'pcifront_sd'. That
    way access to the 'node' will access the right offset.

Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:30 -08:00
Konrad Rzeszutek Wilk
4cf5aa2ffe xen/pciback: Save the number of MSI-X entries to be copied later.
commit d159457b84 upstream.

Commit 8135cf8b09 (xen/pciback: Save
xen_pci_op commands before processing it) broke enabling MSI-X because
it would never copy the resulting vectors into the response.  The
number of vectors requested was being overwritten by the return value
(typically zero for success).

Save the number of vectors before processing the op, so the correct
number of vectors are copied afterwards.

Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:30 -08:00
Konrad Rzeszutek Wilk
d52a248196 xen/pciback: Check PF instead of VF for PCI_COMMAND_MEMORY
commit 8d47065f7d upstream.

Commit 408fb0e5aa (xen/pciback: Don't
allow MSI-X ops if PCI_COMMAND_MEMORY is not set) prevented enabling
MSI-X on passed-through virtual functions, because it checked the VF
for PCI_COMMAND_MEMORY but this is not a valid bit for VFs.

Instead, check the physical function for PCI_COMMAND_MEMORY.

Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:30 -08:00
Juergen Gross
e32b123fee xen/scsiback: correct frontend counting
commit f285aa8db7 upstream.

When adding a new frontend to xen-scsiback don't decrement the number
of active frontends in case of no error. Doing so results in a failure
when trying to remove the xen-pvscsi nexus even if no domain is using
it.

Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:30 -08:00
Robin Murphy
e1d61091db of/irq: Fix msi-map calculation for nonzero rid-base
commit 5d589d81ac upstream.

The existing msi-map code is fine for shifting the entire RID space
upwards, but attempting finer-grained remapping reveals a bug. It turns
out that we are mistakenly treating the msi-base part as an offset, not
as a new base to remap onto, so things get squiffy when rid-base is
nonzero. Fix this, and at the same time add a sanity check against
having msi-map-mask clash with a nonzero rid-base, as that's another
thing one can easily get wrong.

Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Stuart Yoder <stuart.yoder@nxp.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:29 -08:00
Alexandra Yates
023e29e467 i2c: i801: Adding Intel Lewisburg support for iTCO
commit 1a1503c539 upstream.

Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog
resources have been moved to reside under the i801 SMBus host
controller whereas previously they were under the LPC device.

This patch adds Intel lewisburg SMBus support for iTCO device.
It allows to load watchdog dynamically when the hardware is
present.

Fixes: cdc5a3110e ("i2c: i801: add Intel Lewisburg device IDs")
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:28 -08:00
Shawn Lin
be683dfd4c phy: core: fix wrong err handle for phy_power_on
commit b82fcabe21 upstream.

If phy_pm_runtime_get_sync failed but we already
enable regulator, current code return directly without
doing regulator_disable. This patch fix this problem
and cleanup err handle of phy_power_on to be more readable.

Fixes: 3be88125d8 ("phy: core: Support regulator ...")
Cc: Roger Quadros <rogerq@ti.com>
Cc: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:28 -08:00
Sebastian Andrzej Siewior
a2d25804cd PCI/AER: Flush workqueue on device remove to avoid use-after-free
commit 4ae2182b1e upstream.

A Root Port's AER structure (rpc) contains a queue of events.  aer_irq()
enqueues AER status information and schedules aer_isr() to dequeue and
process it.  When we remove a device, aer_remove() waits for the queue to
be empty, then frees the rpc struct.

But aer_isr() references the rpc struct after dequeueing and possibly
emptying the queue, which can cause a use-after-free error as in the
following scenario with two threads, aer_isr() on the left and a
concurrent aer_remove() on the right:

  Thread A                      Thread B
  --------                      --------
  aer_irq():
    rpc->prod_idx++
                                aer_remove():
                                  wait_event(rpc->prod_idx == rpc->cons_idx)
                                  # now blocked until queue becomes empty
  aer_isr():                      # ...
    rpc->cons_idx++               # unblocked because queue is now empty
    ...                           kfree(rpc)
    mutex_unlock(&rpc->rpc_mutex)

To prevent this problem, use flush_work() to wait until the last scheduled
instance of aer_isr() has completed before freeing the rpc struct in
aer_remove().

I reproduced this use-after-free by flashing a device FPGA and
re-enumerating the bus to find the new device.  With SLUB debug, this
crashes with 0x6b bytes (POISON_FREE, the use-after-free magic number) in
GPR25:

  pcieport 0000:00:00.0: AER: Multiple Corrected error received: id=0000
  Unable to handle kernel paging request for data at address 0x27ef9e3e
  Workqueue: events aer_isr
  GPR24: dd6aa000 6b6b6b6b 605f8378 605f8360 d99b12c0 604fc674 606b1704 d99b12c0
  NIP [602f5328] pci_walk_bus+0xd4/0x104

[bhelgaas: changelog, stable tag]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:28 -08:00
Tejun Heo
aff4514876 libata: fix sff host state machine locking while polling
commit 8eee1d3ed5 upstream.

The bulk of ATA host state machine is implemented by
ata_sff_hsm_move().  The function is called from either the interrupt
handler or, if polling, a work item.  Unlike from the interrupt path,
the polling path calls the function without holding the host lock and
ata_sff_hsm_move() selectively grabs the lock.

This is completely broken.  If an IRQ triggers while polling is in
progress, the two can easily race and end up accessing the hardware
and updating state machine state at the same time.  This can put the
state machine in an illegal state and lead to a crash like the
following.

  kernel BUG at drivers/ata/libata-sff.c:1302!
  invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN
  Modules linked in:
  CPU: 1 PID: 10679 Comm: syz-executor Not tainted 4.5.0-rc1+ #300
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
  task: ffff88002bd00000 ti: ffff88002e048000 task.ti: ffff88002e048000
  RIP: 0010:[<ffffffff83a83409>]  [<ffffffff83a83409>] ata_sff_hsm_move+0x619/0x1c60
  ...
  Call Trace:
   <IRQ>
   [<ffffffff83a84c31>] __ata_sff_port_intr+0x1e1/0x3a0 drivers/ata/libata-sff.c:1584
   [<ffffffff83a85611>] ata_bmdma_port_intr+0x71/0x400 drivers/ata/libata-sff.c:2877
   [<     inline     >] __ata_sff_interrupt drivers/ata/libata-sff.c:1629
   [<ffffffff83a85bf3>] ata_bmdma_interrupt+0x253/0x580 drivers/ata/libata-sff.c:2902
   [<ffffffff81479f98>] handle_irq_event_percpu+0x108/0x7e0 kernel/irq/handle.c:157
   [<ffffffff8147a717>] handle_irq_event+0xa7/0x140 kernel/irq/handle.c:205
   [<ffffffff81484573>] handle_edge_irq+0x1e3/0x8d0 kernel/irq/chip.c:623
   [<     inline     >] generic_handle_irq_desc include/linux/irqdesc.h:146
   [<ffffffff811a92bc>] handle_irq+0x10c/0x2a0 arch/x86/kernel/irq_64.c:78
   [<ffffffff811a7e4d>] do_IRQ+0x7d/0x1a0 arch/x86/kernel/irq.c:240
   [<ffffffff86653d4c>] common_interrupt+0x8c/0x8c arch/x86/entry/entry_64.S:520
   <EOI>
   [<     inline     >] rcu_lock_acquire include/linux/rcupdate.h:490
   [<     inline     >] rcu_read_lock include/linux/rcupdate.h:874
   [<ffffffff8164b4a1>] filemap_map_pages+0x131/0xba0 mm/filemap.c:2145
   [<     inline     >] do_fault_around mm/memory.c:2943
   [<     inline     >] do_read_fault mm/memory.c:2962
   [<     inline     >] do_fault mm/memory.c:3133
   [<     inline     >] handle_pte_fault mm/memory.c:3308
   [<     inline     >] __handle_mm_fault mm/memory.c:3418
   [<ffffffff816efb16>] handle_mm_fault+0x2516/0x49a0 mm/memory.c:3447
   [<ffffffff8127dc16>] __do_page_fault+0x376/0x960 arch/x86/mm/fault.c:1238
   [<ffffffff8127e358>] trace_do_page_fault+0xe8/0x420 arch/x86/mm/fault.c:1331
   [<ffffffff8126f514>] do_async_page_fault+0x14/0xd0 arch/x86/kernel/kvm.c:264
   [<ffffffff86655578>] async_page_fault+0x28/0x30 arch/x86/entry/entry_64.S:986

Fix it by ensuring that the polling path is holding the host lock
before entering ata_sff_hsm_move() so that all hardware accesses and
state updates are performed under the host lock.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Link: http://lkml.kernel.org/g/CACT4Y+b_JsOxJu2EZyEf+mOXORc_zid5V1-pLZSroJVxyWdSpw@mail.gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:27 -08:00
Quinn Tran
921d439c67 qla2xxx: Fix stale pointer access.
commit cb43285ff7 upstream.

[ Upstream Commit 84e32a06f4 ]

Commit 84e32a0 ("qla2xxx: Use pci_enable_msix_range() instead of
pci_enable_msix()") introduced a regression when target mode is enabled.
In qla24xx_enable_msix(), ha->max_rsp_queues was incorrectly set
to a value higher than the number of response queues allocated causing
an invalid dereference. Specifically here in qla2x00_init_rings():
    *rsp->in_ptr = 0;

Add additional check to make sure the pointer is valid. following
call stack will be seen

---- 8< ----
RIP: 0010:[<ffffffffa02ccadc>]  [<ffffffffa02ccadc>] qla2x00_init_rings+0xdc/0x320 [qla2xxx]
RSP: 0018:ffff880429447dd8  EFLAGS: 00010082
....
Call Trace:
[<ffffffffa02ceb40>] qla2x00_abort_isp+0x170/0x6b0 [qla2xxx]
[<ffffffffa02c6f77>] qla2x00_do_dpc+0x357/0x7f0 [qla2xxx]
[<ffffffffa02c6c20>] ? qla2x00_relogin+0x260/0x260 [qla2xxx]
[<ffffffff8107d2c9>] kthread+0xc9/0xe0
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
[<ffffffff8172cc6f>] ret_from_fork+0x3f/0x70
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
---- 8< ----

Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:27 -08:00
Cyrille Pitchen
44c7d7625f spi: atmel: fix gpio chip-select in case of non-DT platform
commit 70f340df24 upstream.

The non-DT platform that uses this driver (actually the AVR32) was taking a bad
branch for determining if the IP would use gpio for CS.
Adding the presence of DT as a condition fixes this issue.

Fixes: 4820303480 ("spi: atmel: add support for the internal chip-select of the spi controller")
Reported-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[nicolas.ferre@atmel.com: extract from ml discussion]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:27 -08:00
Nicholas Bellinger
b9d9920212 target: Fix race with SCF_SEND_DELAYED_TAS handling
commit 310d3d314b upstream.

This patch fixes a race between setting of SCF_SEND_DELAYED_TAS
in transport_send_task_abort(), and check of the same bit in
transport_check_aborted_status().

It adds a __transport_check_aborted_status() version that is
used by target_execute_cmd() when se_cmd->t_state_lock is
held, and a transport_check_aborted_status() wrapper for
all other existing callers.

Also, it handles the case where the check happens before
transport_send_task_abort() gets called.  For this, go
ahead and set SCF_SEND_DELAYED_TAS early when necessary,
and have transport_send_task_abort() send the abort.

Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:27 -08:00
Nicholas Bellinger
fb6a326e30 target: Fix remote-port TMR ABORT + se_cmd fabric stop
commit 0f4a943168 upstream.

To address the bug where fabric driver level shutdown
of se_cmd occurs at the same time when TMR CMD_T_ABORTED
is happening resulting in a -1 ->cmd_kref, this patch
adds a CMD_T_FABRIC_STOP bit that is used to determine
when TMR + driver I_T nexus shutdown is happening
concurrently.

It changes target_sess_cmd_list_set_waiting() to obtain
se_cmd->cmd_kref + set CMD_T_FABRIC_STOP, and drop local
reference in target_wait_for_sess_cmds() and invoke extra
target_put_sess_cmd() during Task Aborted Status (TAS)
when necessary.

Also, it adds a new target_wait_free_cmd() wrapper around
transport_wait_for_tasks() for the special case within
transport_generic_free_cmd() to set CMD_T_FABRIC_STOP,
and is now aware of CMD_T_ABORTED + CMD_T_TAS status
bits to know when an extra transport_put_cmd() during
TAS is required.

Note transport_generic_free_cmd() is expected to block on
cmd->cmd_wait_comp in order to follow what iscsi-target
expects during iscsi_conn context se_cmd shutdown.

Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:27 -08:00
Nicholas Bellinger
547551e5a5 target: Fix TAS handling for multi-session se_node_acls
commit ebde1ca5a9 upstream.

This patch fixes a bug in TMR task aborted status (TAS)
handling when multiple sessions are connected to the
same target WWPN endpoint and se_node_acl descriptor,
resulting in TASK_ABORTED status to not be generated
for aborted se_cmds on the remote port.

This is due to core_tmr_handle_tas_abort() incorrectly
comparing se_node_acl instead of se_session, for which
the multi-session case is expected to be sharing the
same se_node_acl.

Instead, go ahead and update core_tmr_handle_tas_abort()
to compare tmr_sess + cmd->se_sess in order to determine
if the LUN_RESET was received on a different I_T nexus,
and TASK_ABORTED status response needs to be generated.

Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:27 -08:00
Nicholas Bellinger
91583a2164 target: Fix LUN_RESET active TMR descriptor handling
commit a6d9bb1c96 upstream.

This patch fixes a NULL pointer se_cmd->cmd_kref < 0
refcount bug during TMR LUN_RESET with active TMRs,
triggered during se_cmd + se_tmr_req descriptor
shutdown + release via core_tmr_drain_tmr_list().

To address this bug, go ahead and obtain a local
kref_get_unless_zero(&se_cmd->cmd_kref) for active I/O
to set CMD_T_ABORTED, and transport_wait_for_tasks()
followed by the final target_put_sess_cmd() to drop
the local ->cmd_kref.

Also add two new checks within target_tmr_work() to
avoid CMD_T_ABORTED -> TFO->queue_tm_rsp() callbacks
ahead of invoking the backend -> fabric put in
transport_cmd_check_stop_to_fabric().

For good measure, also change core_tmr_release_req()
to use list_del_init() ahead of se_tmr_req memory
free.

Reviewed-by: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:27 -08:00
Nicholas Bellinger
3b493f9f06 target: Fix LUN_RESET active I/O handling for ACK_KREF
commit febe562c20 upstream.

This patch fixes a NULL pointer se_cmd->cmd_kref < 0
refcount bug during TMR LUN_RESET with active se_cmd
I/O, that can be triggered during se_cmd descriptor
shutdown + release via core_tmr_drain_state_list() code.

To address this bug, add common __target_check_io_state()
helper for ABORT_TASK + LUN_RESET w/ CMD_T_COMPLETE
checking, and set CMD_T_ABORTED + obtain ->cmd_kref for
both cases ahead of last target_put_sess_cmd() after
TFO->aborted_task() -> transport_cmd_finish_abort()
callback has completed.

It also introduces SCF_ACK_KREF to determine when
transport_cmd_finish_abort() needs to drop the second
extra reference, ahead of calling target_put_sess_cmd()
for the final kref_put(&se_cmd->cmd_kref).

It also updates transport_cmd_check_stop() to avoid
holding se_cmd->t_state_lock while dropping se_cmd
device state via target_remove_from_state_list(), now
that core_tmr_drain_state_list() is holding the
se_device lock while checking se_cmd state from
within TMR logic.

Finally, move transport_put_cmd() release of SGL +
TMR + extended CDB memory into target_free_cmd_mem()
in order to avoid potential resource leaks in TMR
ABORT_TASK + LUN_RESET code-paths.  Also update
target_release_cmd_kref() accordingly.

Reviewed-by: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:27 -08:00
Oliver Neukum
19964740eb cdc-acm:exclude Samsung phone 04e8:685d
commit e912e685f3 upstream.

This phone needs to be handled by a specialised firmware tool
and is reported to crash irrevocably if cdc-acm takes it.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:26 -08:00
Sudip Mukherjee
f021f05c12 Revert "Staging: panel: usleep_range is preferred over udelay"
commit b64a1cbef6 upstream.

This reverts commit ebd43516d3.

We should not be sleeping inside spin_lock.

Fixes: ebd43516d3 ("Staging: panel: usleep_range is preferred over udelay")
Cc: Sirnam Swetha <theonly.ultimate@gmail.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reported-by: Huang, Ying <ying.huang@intel.com>
Tested-by: Huang, Ying <ying.huang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:26 -08:00
Samuel Thibault
16d9f52201 Staging: speakup: Fix getting port information
commit 327b882d3b upstream.

Commit f79b0d9c22 ("staging: speakup: Fixed warning <linux/serial.h>
instead of <asm/serial.h>") broke the port information in the speakup
driver: SERIAL_PORT_DFNS only gets defined if asm/serial.h is included,
and no other header includes asm/serial.h.

We here make sure serialio.c does get the arch-specific definition of
SERIAL_PORT_DFNS from asm/serial.h, if any.

Along the way, this makes sure that we do have information for the
requested serial port number (index)

Fixes: f79b0d9c22 ("staging: speakup: Fixed warning <linux/serial.h> instead of <asm/serial.h>")
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:26 -08:00
Martin K. Petersen
f313f1d809 sd: Optimal I/O size is in bytes, not sectors
commit d0eb20a863 upstream.

Commit ca369d51b3 ("block/sd: Fix device-imposed transfer length
limits") accidentally switched optimal I/O size reporting from bytes to
block layer sectors.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: ca369d51b3
Reviewed-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:26 -08:00
Viresh Kumar
0ac4a2a8ba cpufreq: Fix NULL reference crash while accessing policy->governor_data
commit e4b133cc4b upstream.

There is a race discovered by Juri, where we are able to:
- create and read a sysfs file before policy->governor_data is being set
  to a non NULL value.
  OR
- set policy->governor_data to NULL, and reading a file before being
  destroyed.

And so such a crash is reported:

Unable to handle kernel NULL pointer dereference at virtual address 0000000c
pgd = edfc8000
[0000000c] *pgd=bfc8c835
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 4 PID: 1730 Comm: cat Not tainted 4.5.0-rc1+ #463
Hardware name: ARM-Versatile Express
task: ee8e8480 ti: ee930000 task.ti: ee930000
PC is at show_ignore_nice_load_gov_pol+0x24/0x34
LR is at show+0x4c/0x60
pc : [<c058f1bc>]    lr : [<c058ae88>]    psr: a0070013
sp : ee931dd0  ip : ee931de0  fp : ee931ddc
r10: ee4bc290  r9 : 00001000  r8 : ef2cb000
r7 : ee4bc200  r6 : ef2cb000  r5 : c0af57b0  r4 : ee4bc2e0
r3 : 00000000  r2 : 00000000  r1 : c0928df4  r0 : ef2cb000
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 10c5387d  Table: adfc806a  DAC: 00000051
Process cat (pid: 1730, stack limit = 0xee930210)
Stack: (0xee931dd0 to 0xee932000)
1dc0:                                     ee931dfc ee931de0 c058ae88 c058f1a4
1de0: edce3bc0 c07bfca4 edce3ac0 00001000 ee931e24 ee931e00 c01fcb90 c058ae48
1e00: 00000001 edce3bc0 00000000 00000001 ee931e50 ee8ff480 ee931e34 ee931e28
1e20: c01fb33c c01fcb0c ee931e8c ee931e38 c01a5210 c01fb314 ee931e9c ee931e48
1e40: 00000000 edce3bf0 befe4a00 ee931f78 00000000 00000000 000001e4 00000000
1e60: c00545a8 edce3ac0 00001000 00001000 befe4a00 ee931f78 00000000 00001000
1e80: ee931ed4 ee931e90 c01fbed8 c01a5038 ed085a58 00020000 00000000 00000000
1ea0: c0ad72e4 ee931f78 ee8ff488 ee8ff480 c077f3fc 00001000 befe4a00 ee931f78
1ec0: 00000000 00001000 ee931f44 ee931ed8 c017c328 c01fbdc4 00001000 00000000
1ee0: ee8ff480 00001000 ee931f44 ee931ef8 c017c65c c03deb10 ee931fac ee931f08
1f00: c0009270 c001f290 c0a8d968 ef2cb000 ef2cb000 ee8ff480 00000020 ee8ff480
1f20: ee8ff480 befe4a00 00001000 ee931f78 00000000 00000000 ee931f74 ee931f48
1f40: c017d1ec c017c2f8 c019c724 c019c684 ee8ff480 ee8ff480 00001000 befe4a00
1f60: 00000000 00000000 ee931fa4 ee931f78 c017d2a8 c017d160 00000000 00000000
1f80: 000a9f20 00001000 befe4a00 00000003 c000ffe4 ee930000 00000000 ee931fa8
1fa0: c000fe40 c017d264 000a9f20 00001000 00000003 befe4a00 00001000 00000000
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
1fc0: 000a9f20 00001000 befe4a00 00000003 00000000 00000000 00000003 00000001
pgd = edfc4000
[0000000c] *pgd=bfcac835
1fe0: 00000000 befe49dc 000197f8 b6e35dfc 60070010 00000003 3065b49d 134ac2c9

[<c058f1bc>] (show_ignore_nice_load_gov_pol) from [<c058ae88>] (show+0x4c/0x60)
[<c058ae88>] (show) from [<c01fcb90>] (sysfs_kf_seq_show+0x90/0xfc)
[<c01fcb90>] (sysfs_kf_seq_show) from [<c01fb33c>] (kernfs_seq_show+0x34/0x38)
[<c01fb33c>] (kernfs_seq_show) from [<c01a5210>] (seq_read+0x1e4/0x4e4)
[<c01a5210>] (seq_read) from [<c01fbed8>] (kernfs_fop_read+0x120/0x1a0)
[<c01fbed8>] (kernfs_fop_read) from [<c017c328>] (__vfs_read+0x3c/0xe0)
[<c017c328>] (__vfs_read) from [<c017d1ec>] (vfs_read+0x98/0x104)
[<c017d1ec>] (vfs_read) from [<c017d2a8>] (SyS_read+0x50/0x90)
[<c017d2a8>] (SyS_read) from [<c000fe40>] (ret_fast_syscall+0x0/0x1c)
Code: e5903044 e1a00001 e3081df4 e34c1092 (e593300c)
---[ end trace 5994b9a5111f35ee ]---

Fix that by making sure, policy->governor_data is updated at the right
places only.

Reported-and-tested-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:25 -08:00
Arnd Bergmann
286ab25d69 cpufreq: pxa2xx: fix pxa_cpufreq_change_voltage prototype
commit fb2a24a1c6 upstream.

There are two definitions of pxa_cpufreq_change_voltage, with slightly
different prototypes after one of them had its argument marked 'const'.
Now the other one (for !CONFIG_REGULATOR) produces a harmless warning:

drivers/cpufreq/pxa2xx-cpufreq.c: In function 'pxa_set_target':
drivers/cpufreq/pxa2xx-cpufreq.c:291:36: warning: passing argument 1 of 'pxa_cpufreq_change_voltage' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
   ret = pxa_cpufreq_change_voltage(&pxa_freq_settings[idx]);
                                    ^
drivers/cpufreq/pxa2xx-cpufreq.c:205:12: note: expected 'struct pxa_freqs *' but argument is of type 'const struct pxa_freqs *'
 static int pxa_cpufreq_change_voltage(struct pxa_freqs *pxa_freq)
            ^

This changes the prototype in the same way as the other, which
avoids the warning.

Fixes: 03c2299063 (cpufreq: pxa: make pxa_freqs arrays const)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:25 -08:00
Peter Rosin
5c2bd0c61c hwmon: (ads1015) Handle negative conversion values correctly
commit acc1469439 upstream.

Make the divisor signed as DIV_ROUND_CLOSEST is undefined for negative
dividends when the divisor is unsigned.

Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:25 -08:00
Nishanth Menon
4bbd7acd01 hwmon: (gpio-fan) Remove un-necessary speed_index lookup for thermal hook
commit 000e094914 upstream.

Thermal hook gpio_fan_get_cur_state is only interested in knowing
the current speed index that was setup in the system, this is
already available as part of fan_data->speed_index which is always
set by set_fan_speed. Using get_fan_speed_index is useful when we
have no idea about the fan speed configuration (for example during
fan_ctrl_init).

When thermal framework invokes
gpio_fan_get_cur_state=>get_fan_speed_index via gpio_fan_get_cur_state
especially in a polled configuration for thermal governor, we
basically hog the i2c interface to the extent that other functions
fail to get any traffic out :(.

Instead, just provide the last state set in the driver - since the gpio
fan driver is responsible for the fan state immaterial of override, the
fan_data->speed_index should accurately reflect the state.

Fixes: b5cf88e46b ("(gpio-fan): Add thermal control hooks")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03 15:07:25 -08:00