commit 4e0f5cc650 upstream.
Otherwise the interconnect related code implementing PM runtime will
produce these errors on a failed probe:
omap_uart 48066000.serial: omap_device: omap_device_enable() called from invalid state 1
omap_uart 48066000.serial: use pm_runtime_put_sync_suspend() in driver?
Note that we now also need to check for priv in omap8250_runtime_suspend()
as it has not yet been registered if probe fails. And we need to use
pm_runtime_put_sync() to properly idle the device like we already do
in omap8250_remove().
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c130b666a9 upstream.
Commit f209fa03fc ("serial: 8250_pci: Detach low-level driver during
PCI error recovery") introduces a potential use-after-free in case the
pciserial_init_ports call in serial8250_io_resume fails, which may
happen if a memory allocation fails or if the .init quirk failed for
whatever reason). If this happen, further pci_get_drvdata will return a
pointer to freed memory.
This patch reworks the PCI recovery resume hook to restore the old priv
structure in this case, which should be ok, since the ports were already
detached. Such error during recovery causes us to give up on the
recovery.
Fixes: f209fa03fc ("serial: 8250_pci: Detach low-level driver during PCI error recovery")
Reported-by: Michal Suchanek <msuchanek@suse.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b6ffcf2108 ]
UART uses as EDMA as dma engine on AM437x SoC and therefore, requires
OMAP_DMA_TX_KICK quirk just like AM33xx. So, enable OMAP_DMA_TX_KICK
quirk for AM437x platform as well. While at that, drop use of
of_machine_is_compatible() and instead pass quirks via device data.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6040bc610 upstream.
The reference manual for the i.MX28 recommends to calculate the divisor
as
divisor = (UARTCLK * 32) / baud rate, rounded to the nearest integer
, so let's do this. For a typical setup of UARTCLK = 24 MHz and baud
rate = 115200 this changes the divisor from 6666 to 6667 and so the
actual baud rate improves from 115211.521 Bd (error ≅ 0.01 %) to
115194.240 Bd (error ≅ 0.005 %).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 497e1e16f4 upstream.
A side effect of 89d8232411 ("tty/serial: atmel_serial: BUG: stop DMA
from transmitting in stop_tx") is that the console can be called with
TX path disabled. Then the system would hang trying to push charecters
out in atmel_console_putchar().
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 89d8232411 ("tty/serial: atmel_serial: BUG: stop DMA from transmitting in stop_tx")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31ca2c63fd upstream.
If uart_flush_buffer() is called between atmel_tx_dma() and
atmel_complete_tx_dma(), the circular buffer has been cleared, but not
atmel_port->tx_len.
That leads to a circular buffer overflow (dumping (UART_XMIT_SIZE -
atmel_port->tx_len) bytes).
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f209fa03fc ]
During a PCI error recovery, like the ones provoked by EEH in the ppc64
platform, all IO to the device must be blocked while the recovery is
completed. Current 8250_pci implementation only suspends the port
instead of detaching it, which doesn't prevent incoming accesses like
TIOCMGET and TIOCMSET calls from reaching the device. Those end up
racing with the EEH recovery, crashing it. Similar races were also
observed when opening the device and when shutting it down during
recovery.
This patch implements a more robust IO blockage for the 8250_pci
recovery by unregistering the port at the beginning of the procedure and
re-adding it afterwards. Since the port is detached from the uart
layer, we can be sure that no request will make through to the device
during recovery. This is similar to the solution used by the JSM serial
driver.
I thank Peter Hurley <peter@hurleysoftware.com> for valuable input on
this one over one year ago.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f98c7bce57 upstream.
If DMA is not available (even when configured in DeviceTree), the driver
will fail the startup procedure thus making serial console not
available.
For example this causes boot failure on QEMU ARMv7 (Exynos4210, SMDKC210):
[ 1.302575] OF: amba_device_add() failed (-19) for /amba/pdma@12680000
...
[ 11.435732] samsung-uart 13800000.serial: DMA request failed
[ 72.963893] samsung-uart 13800000.serial: DMA request failed
[ 73.143361] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000000
DMA is not necessary for serial to work, so continue with UART startup
after emitting a warning.
Fixes: 62c37eedb7 ("serial: samsung: add dma reqest/release functions")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c9c858e2f upstream.
The MKS Instruments SCOM-0800 and SCOM-0801 cards (originally by Tenta
Technologies) are 3U CompactPCI serial cards with 4 and 8 serial ports,
respectively. The first 4 ports are implemented by an OX16PCI954 chip,
and the second 4 ports are implemented by an OX16C954 chip on a local
bus, bridged by the second PCI function of the OX16PCI954. The ports
are jumper-selectable as RS-232 and RS-422/485, and the UARTs use a
non-standard oscillator frequency of 20 MHz (base_baud = 1250000).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abe81f3b8e upstream.
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/tty/serial/msm_serial.ko | grep alias
$
After this patch:
$ modinfo drivers/tty/serial/msm_serial.ko | grep alias
alias: of:N*T*Cqcom,msm-uartdmC*
alias: of:N*T*Cqcom,msm-uartdm
alias: of:N*T*Cqcom,msm-uartC*
alias: of:N*T*Cqcom,msm-uart
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bed8a8e70 upstream.
When in RS485 emulation mode, __do_stop_tx_rs485() calls
serial8250_clear_fifos(). This not only clears the FIFOs, but also sets
all bits in their control register (UART_FCR) to 0.
One of the effects of this is the disabling of the FIFOs, which turns
them into single-byte holding registers. The rest of the driver doesn't
know this, which results in the lions share of characters passed into a
write call to be dropped.
(I can supply logic analyzer screenshots if necessary)
This fix replaces the serial8250_clear_fifos() call to
serial8250_clear_and_reinit_fifos() - this prevents the "dropped
characters" issue from manifesting again while retaining the requirement
of clearing the RX FIFO after transmission if the SER_RS485_RX_DURING_TX
flag is disabled.
Signed-off-by: Daniel Jedrychowski <avistel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89d8232411 upstream.
If we don't disable the transmitter in atmel_stop_tx, the DMA buffer
continues to send data until it is emptied.
This cause problems with the flow control (CTS is asserted and data are
still sent).
So, disabling the transmitter in atmel_stop_tx is a sane thing to do.
Tested on at91sam9g35-cm(DMA)
Tested for regressions on sama5d2-xplained(Fifo) and at91sam9g20ek(PDC)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b389f173aa upstream.
When using RS485 in half duplex, RX should be enabled when TX is
finished, and stopped when TX starts.
Before commit 0058f0871e ("tty/serial: atmel: fix RS485 half
duplex with DMA"), RX was not disabled in atmel_start_tx() if the DMA
was used. So, collisions could happened.
But disabling RX in atmel_start_tx() uncovered another bug:
RX was enabled again in the wrong place (in atmel_tx_dma) instead of
being enabled when TX is finished (in atmel_complete_tx_dma), so the
transmission simply stopped.
This bug was not triggered before commit 0058f0871e
("tty/serial: atmel: fix RS485 half duplex with DMA") because RX was
never disabled before.
Moving atmel_start_rx() in atmel_complete_tx_dma() corrects the problem.
Reported-by: Gil Weber <webergil@gmail.com>
Fixes: 0058f0871e
Tested-by: Gil Weber <webergil@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6741f551a0 upstream.
This commit needs to be reverted because it prevents people from
using the serial console as a secondary console with input being
directed to tty0.
IOW, if you boot with console=ttyS0 console=tty0 then all kernels
prior to this commit will produce output on both ttyS0 and tty0
but input will only be taken from tty0. With this patch the serial
console will always be the primary console instead of tty0,
potentially preventing people from getting into their machines in
emergency situations.
Fixes: d03516df83 ("tty: serial: 8250: add CON_CONSDEV to flags")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04da73803c upstream.
The use of IRQF_ONESHOT when registering an interrupt handler with
request_irq() is non-sensical.
Not only that, it also prevents the handler from being threaded when it
otherwise should be w/ IRQ_FORCED_THREADING is enabled. This causes the
following deadlock observed by Sean Nyekjaer on -rt:
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[..]
rt_spin_lock_slowlock from queue_kthread_work
queue_kthread_work from sc16is7xx_irq
sc16is7xx_irq [sc16is7xx] from handle_irq_event_percpu
handle_irq_event_percpu from handle_irq_event
handle_irq_event from handle_level_irq
handle_level_irq from generic_handle_irq
generic_handle_irq from mxc_gpio_irq_handler
mxc_gpio_irq_handler from mx3_gpio_irq_handler
mx3_gpio_irq_handler from generic_handle_irq
generic_handle_irq from __handle_domain_irq
__handle_domain_irq from gic_handle_irq
gic_handle_irq from __irq_svc
__irq_svc from rt_spin_unlock
rt_spin_unlock from kthread_worker_fn
kthread_worker_fn from kthread
kthread from ret_from_fork
Fixes: 9e6f4ca3e5 ("sc16is7xx: use kthread_worker for tx_work and irq")
Reported-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Josh Cartwright <joshc@ni.com>
Cc: linux-rt-users@vger.kernel.org
Cc: Jakub Kicinski <moorray3@wp.pl>
Cc: linux-serial@vger.kernel.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port->console flag is always false, as uart_console() is called
before the serial console has been registered.
Hence for a serial port used as the console, uart_tty_port_shutdown()
will still be called when userspace closes the port, powering it down.
This may lead to a system lock up when the serial console driver writes
to the serial port's registers.
To fix this, move the setting of port->console after the call to
uart_configure_port(), which registers the serial console.
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Reported-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[robh: rebased on tty-linus]
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), the hardware handshake wasn't
functional anymore on Atmel platforms (beside SAMA5D2).
To understand why, one has to understand the flag ATMEL_US_USMODE_HWHS
first:
Before commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), this flag was never set.
Thus, the CTS/RTS where only handled by serial_core (and everything
worked just fine).
This commit introduced the use of the ATMEL_US_USMODE_HWHS flag,
enabling it for all boards when the user space enables flow control.
When the ATMEL_US_USMODE_HWHS is set, the Atmel USART controller
handles a part of the flow control job:
- disable the transmitter when the CTS pin gets high.
- drive the RTS pin high when the DMA buffer transfer is completed or
PDC RX buffer full or RX FIFO is beyond threshold. (depending on the
controller version).
NB: This feature is *not* mandatory for the flow control to work.
(Nevertheless, it's very useful if low latencies are needed.)
Now, the specifics of the ATMEL_US_USMODE_HWHS flag:
- For platforms with DMAC and no FIFOs (sam9x25, sam9x35, sama5D3,
sama5D4, sam9g15, sam9g25, sam9g35)* this feature simply doesn't work.
( source: https://lkml.org/lkml/2016/9/7/598 )
Tested it on sam9g35, the RTS pins always stays up, even when RXEN=1
or a new DMA transfer descriptor is set.
=> ATMEL_US_USMODE_HWHS must not be used for those platforms
- For platforms with a PDC (sam926{0,1,3}, sam9g10, sam9g20, sam9g45,
sam9g46)*, there's another kind of problem. Once the flag
ATMEL_US_USMODE_HWHS is set, the RTS pin can't be driven anymore via
RTSEN/RTSDIS in USART Control Register. The RTS pin can only be driven
by enabling/disabling the receiver or setting RCR=RNCR=0 in the PDC
(Receive (Next) Counter Register).
=> Doing this is beyond the scope of this patch and could add other
bugs, so the original (and working) behaviour should be set for those
platforms (meaning ATMEL_US_USMODE_HWHS flag should be unset).
- For platforms with a FIFO (sama5d2)*, the RTS pin is driven according
to the RX FIFO thresholds, and can be also driven by RTSEN/RTSDIS in
USART Control Register. No problem here.
(This was the use case of commit 1cf6e8fc83 ("tty/serial: at91: fix
RTS line management when hardware handshake is enabled"))
NB: If the CTS pin declared as a GPIO in the DTS, (for instance
cts-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_LOW>), the transmitter will be
disabled.
=> ATMEL_US_USMODE_HWHS flag can be set for this platform ONLY IF the
CTS pin is not a GPIO.
So, the only case when ATMEL_US_USMODE_HWHS can be enabled is when
(atmel_use_fifo(port) &&
!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
Tested on all Atmel USART controller flavours:
AT91SAM9G35-CM (DMAC flavour), AT91SAM9G20-EK (PDC flavour),
SAMA5D2xplained (FIFO flavour).
* the list may not be exhaustive
Cc: <stable@vger.kernel.org> #4.4+ (beware, missing atmel_port variable)
Fixes: 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap_update first reads the IOState register and then triggers
a write if needed. However, GPIOS might be configured as an input so
the read to IOState on this GPIO is the current state which might
be random.
Signed-off-by: Francois Berder <Francois.Berder@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NXP SC16C2552 requires that we always write a reset to the RX FIFO and
TX FIFO whenever we enable the FIFOs
Cc: xe-kernel@external.cisco.com
Signed-off-by: Steve Shih <sshih@cisco.com>
Signed-off-by: David Singleton <davsingl@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case where head == 0 on the circular buffer, there should be one
DMA buffer, not two. The second zero-length buffer would break the
lpuart driver, transfer would never complete.
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Tested-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 4fe0d15488 ("PCI: Use positive flags in pci_alloc_irq_vectors()")
replaces flags from negative to positive values which makes mandatory to have
the last argument in pci_alloc_irq_vectors() non-zero (if we want to be no-op).
This basically drops MSI enabling in 8250_lpss driver.
Restore desired behaviour in 8250_lpss by passing PCI_IRQ_ALL_TYPES instead of
0 to pci_alloc_irq_vectors().
Fixes: 60a9244a5d ("serial: 8250_lpss: enable MSI for Intel Quark")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 761ed4a945 ('tty: serial_core: convert uart_close to use
tty_port_close') started setting the ttyport console flag for serial
drivers. This is causing crashes, hangs, or garbage output on several
platforms because the serial shutdown is skipped and IRQs are left
enabled.
Partially revert commit 761ed4a945 and drop reporting UART tty_ports
as a console leaving the console handling to the serial_core as it was
before.
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Reported-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Reported-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At this point, 'value' is always a byte, then this code is clearing
bit 15, which is already clear. I meant to clear bit 7.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch Adds the new compatible string for ZynqMP SoC.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `stm32_serial_remove':
stm32-usart.c:(.text+0xcea1a): undefined reference to `bad_dma_ops'
stm32-usart.c:(.text+0xcea7a): undefined reference to `bad_dma_ops'
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/stm32-usart.c: In function ‘stm32_receive_chars’:
drivers/tty/serial/stm32-usart.c:130: warning: comparison is always true due to limited range of data type
drivers/tty/serial/stm32-usart.c: In function ‘stm32_tx_dma_complete’:
drivers/tty/serial/stm32-usart.c:177: warning: comparison is always false due to limited range of data type
stm32_usart_offsets.icr is u8, while UNDEF_REG = ~0 is int, and thus
0xffffffff.
As all registers in stm32_usart_offsets are u8, change the definition of
UNDEF_REG to 0xff to fix this.
Fixes: ada8618ff3 ("serial: stm32: adding support for stm32f7")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big TTY and Serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by some
serial drivers, and they were all acked by the DMA maintainer. Also in
here is the long-suffering ACPI SPCR patchset, which was passed around
from maintainer to maintainer like a hot-potato. Seems I was the
sucker^Wlucky one. All of those patches have been acked by the various
subsystem maintainers as well.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNjEPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspwIcAn2uN
qCD8xQJ0Cs61hD1nUzhNygG8AJ94I4zz/fPGpyh/CtJfLQwtUdLhNA==
=Rken
-----END PGP SIGNATURE-----
Merge tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial updates from Greg KH:
"Here is the big tty and serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by
some serial drivers, and they were all acked by the DMA maintainer.
Also in here is the long-suffering ACPI SPCR patchset, which was
passed around from maintainer to maintainer like a hot-potato. Seems I
was the sucker^Wlucky one. All of those patches have been acked by the
various subsystem maintainers as well.
All of this has been in linux-next with no reported issues"
* tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (111 commits)
Revert "serial: pl011: add console matching function"
MAINTAINERS: update entry for atmel_serial driver
serial: pl011: add console matching function
ARM64: ACPI: enable ACPI_SPCR_TABLE
ACPI: parse SPCR and enable matching console
of/serial: move earlycon early_param handling to serial
Revert "drivers/tty: Explicitly pass current to show_stack"
tty: amba-pl011: Don't complain on -EPROBE_DEFER when no irq
nios2: dts: 10m50: Add tx-threshold parameter
serial: 8250: Set Altera 16550 TX FIFO Threshold
serial: 8250: of: Load TX FIFO Threshold from DT
Documentation: dt: serial: Add TX FIFO threshold parameter
drivers/tty: Explicitly pass current to show_stack
serial: imx: Fix DCD reading
serial: stm32: mark symbols static where possible
serial: xuartps: Add some register initialisation to cdns_early_console_setup()
serial: xuartps: Removed unwanted checks while reading the error conditions
serial: xuartps: Rewrite the interrupt handling logic
serial: stm32: use mapbase instead of membase for DMA
tty/serial: atmel: fix fractional baud rate computation
...
Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems that
flow through me. Nothing major that I can discern, full details are in
the shortlog.
All have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFUEABECABYFAlfyOIQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfsp9OQAlRy3
gSKfQUlXjTs96Bx/I5PtWysAn0r8nyKZoP1oSgsTddOCEeXngTXc
=4uPs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems
that flow through me. Nothing major that I can discern, full details
are in the shortlog.
All have been in the linux-next tree with no reported issues"
* tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (144 commits)
drivers/misc/hpilo: Changes to support new security states in iLO5 FW
at25: fix debug and error messaging
misc/genwqe: ensure zero initialization
vme: fake: remove unexpected unlock in fake_master_set()
vme: fake: mark symbols static where possible
spmi: pmic-arb: Return an error code if sanity check fails
Drivers: hv: get rid of id in struct vmbus_channel
Drivers: hv: make VMBus bus ids persistent
mcb: Add a dma_device to mcb_device
mcb: Enable PCI bus mastering by default
mei: stop the stall timer worker if not needed
clk: probe common clock drivers earlier
vme: fake: fix build for 64-bit dma_addr_t
ttyprintk: Neaten and simplify printing
mei: me: add kaby point device ids
coresight: tmc: mark symbols static where possible
coresight: perf: deal with error condition properly
Drivers: hv: hv_util: Avoid dynamic allocation in time synch
fpga manager: Add hardware dependency to Zynq driver
Drivers: hv: utils: Support TimeSync version 4.0 protocol samples.
...
* device-properties:
serial: 8250_dw: Add quirk for APM X-Gene SoC
ACPI / LPSS: Provide build-in properties of the UART
ACPI / APD: Provide build-in properties of the UART
driver core: Don't leak secondary fwnode on device removal
This reverts commit 8b8f347d3a as it
causes build errors in linux-next
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Aleksey Makarov <aleksey.makarov@linaro.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds function pl011_console_match() that implements
method match of struct console. It allows to match consoles against
data specified in a string, for example taken from command line or
compiled by ACPI SPCR table handler.
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'ARM Server Base Boot Requiremets' [1] mentions SPCR (Serial Port
Console Redirection Table) [2] as a mandatory ACPI table that
specifies the configuration of serial console.
Defer initialization of DT earlycon until ACPI/DT decision is made.
Parse the ACPI SPCR table, setup earlycon if required,
enable specified console.
Thanks to Peter Hurley for explaining how this should work.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.den0044a/index.html
[2] https://msdn.microsoft.com/en-us/library/windows/hardware/dn639132(v=vs.85).aspx
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have multiple "earlycon" early_param handlers - merge the DT one into
the main earlycon one. It's a cleanup that also will be useful
to defer setting up DT console until ACPI/DT decision is made.
Rename the exported function to avoid clashing with the function from
arch/microblaze/kernel/prom.c
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't complain on -EPROBE_DEFER when attempting to get the irq.
the driver probe will be retried later.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Altera 16550 soft IP UART requires 2 additional registers for
TX FIFO threshold support. These 2 registers enable the TX FIFO
Low Watermark and set the TX FIFO Low Watermark.
Set the TX FIFO threshold to the FIFO size - tx_loadsz.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize the tx_loadsz parameter from passed in devicetree
tx-threshold parameter.
The tx_loadsz is calculated as the number of bytes to fill FIFO
when tx-threshold is triggered.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USR2_DCDIN bit is tested for in register usr1. As the name
suggests the usr2 register should be used instead. This fixes
reading the Carrier detect status.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes: 90ebc48386 ("serial: imx: repair and complete handshaking")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@vger.kernel.org> # 4.5+
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get 2 warnings when building kernel with W=1:
drivers/tty/serial/stm32-usart.c:63:5: warning: no previous prototype for 'stm32_pending_rx' [-Wmissing-prototypes]
drivers/tty/serial/stm32-usart.c:88:15: warning: no previous prototype for 'stm32_get_char' [-Wmissing-prototypes]
In fact, these two functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add initialisation of control register and baud rate to
cdns_early_console_setup(), required when running kernel standalone
without a boot loader. Baud rate is only initialised when specified in
earlycon command-line option, otherwise it is assumed this has been
set by a boot loader. Updated Documentation/kernel-parameters.txt
accordingly.
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch Remove the unwated checks while reading the parity,framing,
overrun and Break detection errors.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[stelford@cadence.com: cherry picked from
https://github.com/Xilinx/linux-xlnx commit
b1cf74970df5470ffbc8e7876a9edf5e3498ef94]
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing interrupt handling logic has following issues.
- Upon a parity error with default configuration, the control
never comes out of the ISR thereby hanging Linux.
- The error handling logic around framing and parity error are buggy.
There are chances that the errors will never be captured.
This patch ensures that the status registers are cleared on all cases so
that a hang situation never arises.
Signed-off-by: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[stelford@cadence.com: cherry picked from
https://github.com/Xilinx/linux-xlnx commit
ac297e20d399850d7a8e373b6eccf2e183c15165 with manual conflict resolution]
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building this driver with a 64-bit dma_addr_t type results in
a compiler warning:
drivers/tty/serial/stm32-usart.c: In function 'stm32_of_dma_rx_probe':
drivers/tty/serial/stm32-usart.c:746:20: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/tty/serial/stm32-usart.c: In function 'stm32_of_dma_tx_probe':
drivers/tty/serial/stm32-usart.c:818:20: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
While the type conversion here is harmless, this hints at a different
problem: we pass an __iomem pointer into a DMA engine, which expects
a phys_addr_t. This happens to work because stm32 has no MMU and
ioremap() is an identity mapping here, but it's still an incorrect
API use. Using dma_addr_t is doubly wrong here, because that would
be the result of dma_map_single() rather than the physical address.
Using the mapbase instead fixes multiple issues:
- the warning is gone
- we don't go through ioremap in error
- the cast is gone, making it use the correct resource_size_t/phys_addr_t
type in the process.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem with previous code was it rounded values in wrong
place and produced wrong baud rate in some cases.
Signed-off-by: Alexey Starikovskiy <aystarik@gmail.com>
[nicolas.ferre@atmel.com: port to newer kernel and add commit log]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch makes changes not to enable parity error interrupt.
With the current implementation, each parity error results in
two distinct interrupts (almost always). The first one is normal
parity error interrupt with no data in the fifo and the second one
is a proper Rx interrupt with the received data in the fifo. By
disabling parity error interrupt we still ensure handling of
parity errors as for the Rx fifo interrupt the parity error still
shows up in the interrupt status register. Considering the fact
that the by default INPCK and IGNPAR are not set, this is the
optimal implementation for parity error handling.
Signed-off-by: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[stelford@cadence.com: cherry picked from
https://github.com/Xilinx/linux-xlnx commit
bf9f610b445e2c9ed33c41e1e0e30b43be4e1f97 with manual conflict
resolution]
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
