[ Upstream commit 426849e661 ]
stmmac_tso_allocator can fail to set the Last Descriptor bit
on a descriptor that actually was the last descriptor.
This happens when the buffer of the last descriptor ends
up having a size of exactly TSO_MAX_BUFF_SIZE.
When the IP eventually reaches the next last descriptor,
which actually has the bit set, the DMA will hang.
When the DMA hangs, we get a tx timeout, however,
since stmmac does not do a complete reset of the IP
in stmmac_tx_timeout, we end up in a state with
completely hung TX.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d220b942a4 ]
ethoc_reset enables device interrupts, ethoc_interrupt may schedule a
NAPI poll before NAPI is enabled in the ethoc_open, which results in
device being unable to send or receive anything until it's closed and
reopened. In case the device is flooded with ingress packets it may be
unable to recover at all.
Move napi_enable above ethoc_reset in the ethoc_open to fix that.
Fixes: a170285772 ("net: Add support for the OpenCores 10/100 Mbps Ethernet MAC.")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a53cb29b0a ]
Adding a vxlan interface to a socket isn't symmetrical, while adding
is done in vxlan_open() the deletion is done in vxlan_dellink().
This can cause a use-after-free error when we close the vxlan
interface before deleting it.
We add vxlan_vs_del_dev() to match vxlan_vs_add_dev() and call
it from vxlan_stop() to match the call from vxlan_open().
Fixes: 56ef9c909b ("vxlan: Move socket initialization to within rtnl scope")
Acked-by: Jiri Benc <jbenc@redhat.com>
Tested-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e7519f9926 ]
Take uld mutex to avoid race between cxgb_up() and
cxgb4_register_uld() to enable napi for the same uld
queue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 35cf284556 ]
After commit 0c1d70af92 ("net: use dst_cache for vxlan device"),
cached dst entries could be leaked when more than one remote was
present for a given vxlan_fdb entry, causing subsequent netns
operations to block indefinitely and "unregister_netdevice: waiting
for lo to become free." messages to appear in the kernel log.
Fix by properly releasing cached dst and freeing resources in this
case.
Fixes: 0c1d70af92 ("net: use dst_cache for vxlan device")
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3968d38917 ]
Apparently multi-cos isn't working for bnx2x quite some time -
driver implements ndo_select_queue() to allow queue-selection
for FCoE, but the regular L2 flow would cause it to modulo the
fallback's result by the number of queues.
The fallback would return a queue matching the needed tc
[via __skb_tx_hash()], but since the modulo is by the number of TSS
queues where number of TCs is not accounted, transmission would always
be done by a queue configured into using TC0.
Fixes: ada7c19e6d ("bnx2x: use XPS if possible for bnx2x_select_queue instead of pure hash")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2836b4f224 ]
Since virtio does not provide it's own ndo_features_check handler,
TSO, and now checksum offload, are disabled for stacked vlans.
Re-enable the support and let the host take care of it. This
restores/improves Guest-to-Guest performance over Q-in-Q vlans.
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc6e9de62a ]
At least some of the be2net cards do not seem to be capabled
of performing checksum offload computions on Q-in-Q packets.
In these case, the recevied checksum on the remote is invalid
and TCP syn packets are dropped.
This patch adds a call to check disbled acceleration features
on Q-in-Q tagged traffic.
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f289978835 ]
The 88m1101 has an errata when configuring autoneg. However, it was
being applied to many other Marvell PHYs as well. Limit its scope to
just the 88m1101.
Fixes: 76884679c6 ("phylib: Add support for Marvell 88e1111S and 88e1145")
Reported-by: Daniel Walker <danielwa@cisco.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73dd3a4839 ]
Currently when firmware command gets stuck or it takes long time to
complete, the driver command will get timeout and the command slot is
freed and can be used for new commands, and if the firmware receive new
command on the old busy slot its behavior is unexpected and this could
be harmful.
To fix this when the driver command gets timeout we return failure,
but we don't free the command slot and we wait for the firmware to
explicitly respond to that command.
Once all the entries are busy we will stop processing new firmware
commands.
Fixes: 9cba4ebcf3 ('net/mlx5: Fix potential deadlock in command mode change')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 751da2a69b ]
As of 7bb11dc9f5 and 0622cab034, bond slaves in a 3ad bond are not
removed from the aggregator when they are down, and the active slave count
is NOT equal to number of ports in the aggregator, but rather the number
of ports in the aggregator that are still enabled. The sysfs spew for
bonding_show_ad_num_ports() has a comment that says "Show number of active
802.3ad ports.", but it's currently showing total number of ports, both
active and inactive. Remedy it by using the same logic introduced in
0622cab034 in __bond_3ad_get_active_agg_info(), so sysfs, procfs and
netlink all report the number of active ports. Note that this means that
IFLA_BOND_AD_INFO_NUM_PORTS really means NUM_ACTIVE_PORTS instead of
NUM_PORTS, and thus perhaps should be renamed for clarity.
Lightly tested on a dual i40e lacp bond, simulating link downs with an ip
link set dev <slave2> down, was able to produce the state where I could
see both in the same aggregator, but a number of ports count of 1.
MII Status: up
Active Aggregator Info:
Aggregator ID: 1
Number of ports: 2 <---
Slave Interface: ens10
MII Status: up <---
Aggregator ID: 1
Slave Interface: ens11
MII Status: up
Aggregator ID: 1
MII Status: up
Active Aggregator Info:
Aggregator ID: 1
Number of ports: 1 <---
Slave Interface: ens10
MII Status: down <---
Aggregator ID: 1
Slave Interface: ens11
MII Status: up
Aggregator ID: 1
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 486181bcb3 ]
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use a new USB device ID for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3c1950371 ]
Pause bit should set when RX pause is on, not TX pause.
Also, setting Asym_Pause is incorrect, and should be turned off.
Fixes: 665bc53969 ("net/mlx5e: Use new ethtool get/set link ksettings API")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1a4a5bf52a ]
The current codes only deal with the case that the skb is dropped, it
may meet one use-after-free issue when NF_HOOK returns 0 that means
the skb is stolen by one netfilter rule or hook.
When one netfilter rule or hook stoles the skb and return NF_STOLEN,
it means the skb is taken by the rule, and other modules should not
touch this skb ever. Maybe the skb is queued or freed directly by the
rule.
Now uses the nf_hook instead of NF_HOOK to get the result of netfilter,
and check the return value of nf_hook. Only when its value equals 1, it
means the skb could go ahead. Or reset the skb as NULL.
BTW, because vrf_rcv_finish is empty function, so needn't invoke it
even though nf_hook returns 1. But we need to modify vrf_rcv_finish
to deal with the NF_STOLEN case.
There are two cases when skb is stolen.
1. The skb is stolen and freed directly.
There is nothing we need to do, and vrf_rcv_finish isn't invoked.
2. The skb is queued and reinjected again.
The vrf_rcv_finish would be invoked as okfn, so need to free the
skb in it.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75cf067953 upstream.
Add missing endianness conversion when using the USB device-descriptor
bcdDevice field to construct a firmware file name.
Fixes: 8ef80aef11 ("[IRDA]: irda-usb.c: STIR421x cleanups")
Cc: Nick Fedchik <nfedchik@atlantic-link.com.ua>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebeb36670e upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 36bcce4306 ("ath9k_htc: Handle storage devices")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c8cb9ad03 upstream.
Command buffers (skb's) are allocated by the main driver, and freed upon
the last use. That last use is often in mwifiex_free_cmd_buffer(). In
the meantime, if the command buffer gets used by the PCI driver, we map
it as DMA-able, and store the mapping information in the 'cb' memory.
However, if a command was in-flight when resetting the device (and
therefore was still mapped), we don't get a chance to unmap this memory
until after the core has cleaned up its command handling.
Let's keep a refcount within the PCI driver, so we ensure the memory
only gets freed after we've finished unmapping it.
Noticed by KASAN when forcing a reset via:
echo 1 > /sys/bus/pci/.../reset
The same code path can presumably be exercised in remove() and
shutdown().
[ 205.390377] mwifiex_pcie 0000:01:00.0: info: shutdown mwifiex...
[ 205.400393] ==================================================================
[ 205.407719] BUG: KASAN: use-after-free in mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie] at addr ffffffc0ad471b28
[ 205.419040] Read of size 16 by task bash/1913
[ 205.423421] =============================================================================
[ 205.431625] BUG skbuff_head_cache (Tainted: G B ): kasan: bad access detected
[ 205.439815] -----------------------------------------------------------------------------
[ 205.439815]
[ 205.449534] INFO: Allocated in __build_skb+0x48/0x114 age=1311 cpu=4 pid=1913
[ 205.456709] alloc_debug_processing+0x124/0x178
[ 205.461282] ___slab_alloc.constprop.58+0x528/0x608
[ 205.466196] __slab_alloc.isra.54.constprop.57+0x44/0x54
[ 205.471542] kmem_cache_alloc+0xcc/0x278
[ 205.475497] __build_skb+0x48/0x114
[ 205.479019] __netdev_alloc_skb+0xe0/0x170
[ 205.483244] mwifiex_alloc_cmd_buffer+0x68/0xdc [mwifiex]
[ 205.488759] mwifiex_init_fw+0x40/0x6cc [mwifiex]
[ 205.493584] _mwifiex_fw_dpc+0x158/0x520 [mwifiex]
[ 205.498491] mwifiex_reinit_sw+0x2c4/0x398 [mwifiex]
[ 205.503510] mwifiex_pcie_reset_notify+0x114/0x15c [mwifiex_pcie]
[ 205.509643] pci_reset_notify+0x5c/0x6c
[ 205.513519] pci_reset_function+0x6c/0x7c
[ 205.517567] reset_store+0x68/0x98
[ 205.521003] dev_attr_store+0x54/0x60
[ 205.524705] sysfs_kf_write+0x9c/0xb0
[ 205.528413] INFO: Freed in __kfree_skb+0xb0/0xbc age=131 cpu=4 pid=1913
[ 205.535064] free_debug_processing+0x264/0x370
[ 205.539550] __slab_free+0x84/0x40c
[ 205.543075] kmem_cache_free+0x1c8/0x2a0
[ 205.547030] __kfree_skb+0xb0/0xbc
[ 205.550465] consume_skb+0x164/0x178
[ 205.554079] __dev_kfree_skb_any+0x58/0x64
[ 205.558304] mwifiex_free_cmd_buffer+0xa0/0x158 [mwifiex]
[ 205.563817] mwifiex_shutdown_drv+0x578/0x5c4 [mwifiex]
[ 205.569164] mwifiex_shutdown_sw+0x178/0x310 [mwifiex]
[ 205.574353] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[ 205.580398] pci_reset_notify+0x5c/0x6c
[ 205.584274] pci_dev_save_and_disable+0x24/0x6c
[ 205.588837] pci_reset_function+0x30/0x7c
[ 205.592885] reset_store+0x68/0x98
[ 205.596324] dev_attr_store+0x54/0x60
[ 205.600017] sysfs_kf_write+0x9c/0xb0
...
[ 205.800488] Call trace:
[ 205.802980] [<ffffffc00020a69c>] dump_backtrace+0x0/0x190
[ 205.808415] [<ffffffc00020a96c>] show_stack+0x20/0x28
[ 205.813506] [<ffffffc0005d020c>] dump_stack+0xa4/0xcc
[ 205.818598] [<ffffffc0003be44c>] print_trailer+0x158/0x168
[ 205.824120] [<ffffffc0003be5f0>] object_err+0x4c/0x5c
[ 205.829210] [<ffffffc0003c45bc>] kasan_report+0x334/0x500
[ 205.834641] [<ffffffc0003c3994>] check_memory_region+0x20/0x14c
[ 205.840593] [<ffffffc0003c3b14>] __asan_loadN+0x14/0x1c
[ 205.845879] [<ffffffbffc46171c>] mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie]
[ 205.854282] [<ffffffbffc461864>] mwifiex_pcie_delete_cmdrsp_buf+0x94/0xa8 [mwifiex_pcie]
[ 205.862421] [<ffffffbffc462028>] mwifiex_pcie_free_buffers+0x11c/0x158 [mwifiex_pcie]
[ 205.870302] [<ffffffbffc4620d4>] mwifiex_pcie_down_dev+0x70/0x80 [mwifiex_pcie]
[ 205.877736] [<ffffffbffc1397a8>] mwifiex_shutdown_sw+0x190/0x310 [mwifiex]
[ 205.884658] [<ffffffbffc4606b4>] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[ 205.892446] [<ffffffc000635f54>] pci_reset_notify+0x5c/0x6c
[ 205.898048] [<ffffffc00063a044>] pci_dev_save_and_disable+0x24/0x6c
[ 205.904350] [<ffffffc00063cf0c>] pci_reset_function+0x30/0x7c
[ 205.910134] [<ffffffc000641118>] reset_store+0x68/0x98
[ 205.915312] [<ffffffc000771588>] dev_attr_store+0x54/0x60
[ 205.920750] [<ffffffc00046f53c>] sysfs_kf_write+0x9c/0xb0
[ 205.926182] [<ffffffc00046dfb0>] kernfs_fop_write+0x184/0x1f8
[ 205.931963] [<ffffffc0003d64f4>] __vfs_write+0x6c/0x17c
[ 205.937221] [<ffffffc0003d7164>] vfs_write+0xf0/0x1c4
[ 205.942310] [<ffffffc0003d7da0>] SyS_write+0x78/0xd8
[ 205.947312] [<ffffffc000204634>] el0_svc_naked+0x24/0x28
...
[ 205.998268] ==================================================================
This bug has been around in different forms for a while. It was sort of
noticed in commit 955ab095c5 ("mwifiex: Do not kfree cmd buf while
unregistering PCIe"), but it just fixed the double-free, without
acknowledging the potential for use-after-free.
Fixes: fc33146090 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e2f18f064 upstream.
nl80211 provides the NL80211_SCAN_FLAG_RANDOM_ADDR for every scan
request that should be randomized; the absence of such a flag means we
should not randomize. However, mwifiex was stashing the latest
randomization request and *always* using it for future scans, even those
that didn't set the flag.
Let's zero out the randomization info whenever we get a scan request
without NL80211_SCAN_FLAG_RANDOM_ADDR. I'd prefer to remove
priv->random_mac entirely (and plumb the randomization MAC properly
through the call sequence), but the spaghetti is a little difficult to
unravel here for me.
Fixes: c2a8f0ff9c ("mwifiex: support random MAC address for scanning")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46cfa2148e upstream.
Current channel switch implementation sets 8812ae RFE reg value assuming
that device always has type 2.
Extend possible RFE types set and write corresponding reg values.
Source for new code is
http://dlcdnet.asus.com/pub/ASUS/wireless/PCE-AC51/DR_PCE_AC51_20232801152016.zip
Signed-off-by: Maxim Samoylov <max7255@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7ee74b56f upstream.
This event is used by the Firmware to limit the RX BA win size
for a specific link.
The event handler updates the new size in the mac's sta->sta struct.
BA sessions opened for that link will use the new restricted
win_size. This limitation remains until a new update is received or
until the link is closed.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42c7372a11 upstream.
When starting a new BA session, we must pass the win_size to the FW.
To do this we take max_rx_aggregation_subframes (BA RX win size)
which is stored in ieee80211_sta structure (e.g per link and not per HW)
We will use the value stored per link when passing the win_size to
firmware through the ACX_BA_SESSION_RX_SETUP command.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 922c60e89d ]
If an error is encountered in mdio_mux_init(), the error path will call
mdiobus_free(). Since mdiobus_register() has been called prior to
mdio_mux_init(), the bus->state will not be MDIOBUS_UNREGISTERED. This
causes a BUG_ON() in mdiobus_free(). To correct this issue, add an
error path for mdio_mux_init() which calls mdiobus_unregister() prior to
mdiobus_free().
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: 98bc865a1e ("net: mdio-mux: Add MDIO mux driver for iProc SoCs")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ac45bd93a5 ]
We have the number of longs, but we need to calculate the number of
bytes required.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5294b83086 ]
We call skb_cow_data, which is good anyway to ensure we can actually
modify the skb as such (another error from prior). Now that we have the
number of fragments required, we can safely allocate exactly that amount
of memory.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cc4b7cb86 upstream.
The driver was making changes to the skb_header without
ensuring it was writable (i.e. uncloned).
This patch also removes some boiler plate header size
checking/adjustment code as that is also handled by the
skb_cow_header function used to make header writable.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 455a1eb465 upstream.
The incoming skb header may be resized if header space is
insufficient, which might change the data adddress in the skb.
Ensure that a cached pointer to that data is correctly set by
moving assignment to after any possible changes.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 251fe09f13 upstream.
This is a static analysis fix. The warning is:
drivers/net/wireless/intel/iwlwifi/mvm/fw-dbg.c:912 iwl_mvm_fw_dbg_collect()
warn: integer overflows 'sizeof(*desc) + len'
I guess this code is supposed to take a NUL character, but if we write
zero bytes then it tries to write -1 characters and crashes.
Fixes: c91b865cb1 ("iwlwifi: mvm: support description for user triggered fw dbg collection")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b70f07686 upstream.
When driver needs to access the contents of a streaming DMA buffer
without unmapping it it should call dma_sync_single_for_cpu().
Once the call has been made, the CPU "owns" the DMA buffer and can
work with it as needed.
Before the device accesses the buffer, however, ownership should be
transferred back to it with dma_sync_single_for_device().
Both calls weren't performed by the driver, resulting with odd paging
errors on some platforms. Fix it.
Fixes: a6c4fb4441 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c56108b58a upstream.
In DQA mode, first_agg_queue is initialized to
IWL_MVM_DQA_MIN_DATA_QUEUE. This causes two bugs in the tx response
flow:
1. When TX fails, we set IEEE80211_TX_STAT_AMPDU_NO_BACK regardless
if we actually have aggregation open on the queue. This causes
mac80211 to send a BAR frame even though there is no aggregation
open.
Fix that by simply checking the AMPDU flag that is set on by
mac80211 for AMPDU packets.
2. When reclaiming frames in aggregation mode, we reclaim based on
scheduler ssn and not the SN.
The reason is that scheduler ssn may be ahead of SN due to a hole
in the BA window that was filled.
However, if we have aggregations open on IWL_MVM_DQA_BSS_CLIENT_QUEUE
the reclaim flow will still go to the code of non-aggregation
instead of the aggregation code since IWL_MVM_DQA_BSS_CLIENT_QUEUE
is smaller than IWL_MVM_DQA_MIN_DATA_QUEUE, although it is a valid
aggregation queue.
Fix that by always using the aggregation reclaim code by default in
DQA mode (currently it is implicitly used by default for all queues
except the reserved BSS queue).
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94c3e614df upstream.
In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05e5a7e58d upstream.
Instead of setting the tx_cmd length in the mvm code, which is
complicated by the fact that DQA may want to temporarily store
the SKB on the side, adjust the length in the PCIe code which
also knows about this since it's responsible for duplicating
all those headers that are account for in this code.
As the PCIe code already relies on the tx_cmd->len field, this
doesn't really introduce any new dependencies.
To make this possible we need to move the memcpy() of the TX
command until after it was updated.
This does even simplify the code though, since the PCIe code
already does a lot of manipulations to build A-MSDUs correctly
and changing the length becomes a simple operation to see how
much was added/removed, rather than predicting it.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6574dc943f upstream.
Since offchannel activity doesn't always require a BSS, e.g. ANQP
sessions, offchannel frames should not use the BSS queue, because it
might not be initialized.
Use the auxilary queue instead
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5351f9ab25 upstream.
When NSSN is behind the reorder buffer due to timeout
the reorder timer isn't getting re-armed until NSSN
catches up. Fix it.
Fixes: 0690405fef ("iwlwifi: mvm: add reorder timeout per frame")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c6262b754 upstream.
Our 9000 device supports 64 bit DMA address for RX only, and
not for TX.
Setting DMA mask to 64 for the whole device is erroneous - we
can do it only for a000 devices where device is capable of
both RX & TX DMA with 64 bit address space.
Fixes: 96a6497bc3 ("iwlwifi: pcie: add 9000 series multi queue rx DMA support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ce4a03852 upstream.
shift_param is defined and set in iwl_pcie_load_cpu_sections but not
used. Fix this to avoid -Wunused-but-set-variable warning.
The code using it turned into dead code with commit dcab8ecd56
("iwlwifi: mvm: support ucode load for family_8000 B0 only") which
added a separate function iwl_pcie_load_given_ucode_8000 (then 8000b)
for IWL_DEVICE_FAMILY_8000. Commit 76f8c0e17e ("iwlwifi: pcie:
remove dead code") removed the dead code but left shift_param as is.
iwlwifi/pcie/trans.c: In function ‘iwl_pcie_load_cpu_sections’:
iwlwifi/pcie/trans.c:871:6: warning: variable ‘shift_param’ set but not used [-Wunused-but-set-variable]
Fixes: dcab8ecd56 ("iwlwifi: mvm: support ucode load for family_8000 B0 only")
Fixes: 76f8c0e17e ("iwlwifi: pcie: remove dead code")
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Liad Kaufman <liad.kaufman@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[removed some unnecessary braces]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04fa3e680b upstream.
David reported that the code I added uses the decrement
and increment operator on a boolean variable.
Fix that.
Fixes: 0cd58eaab1 ("iwlwifi: pcie: allow the op_mode to block the tx queues")
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd05a5bd6b upstream.
We don't really need clear the skb's status area nor store the
dev_cmd into it until we really commit to the frame by handing
it to the transport - defer those operations until just before
we do that.
This doesn't entirely fix the bug with frames not getting sent
out after having been deferred due to DQA, because it doesn't
restore the info->driver_data[0] place that was already set to
zero (or another value) by the A-MSDU logic.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bac453ab37 upstream.
For unified images, we shouldn't restart the HW if suspend fails. The
only reason for restarting the HW with non-unified images is to go
back to the D0 image.
Fixes: 23ae61282b ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8320d75b5 upstream.
IWL6000G2B_UCODE_API_MAX is not defined. ucode_api_max of
IWL_DEVICE_6030 uses IWL6000G2_UCODE_API_MAX. Use this also for
MODULE_FIRMWARE.
Fixes: 9d9b21d1b6 ("iwlwifi: remove IWL_*_UCODE_API_OK")
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5b60de697 upstream.
This patch fixes the issue specific to AP. AP is started with WEP
security and external station is connected to it. Data path works
in this case. Now if AP is restarted with WPA/WPA2 security,
station is able to connect but ping fails.
Driver skips the deletion of WEP keys if interface type is AP.
Removing that redundant check resolves the issue.
Fixes: e57f1734d8 ("mwifiex: add key material v2 support")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6183468a23 upstream.
Similar to commit fcd2042e8d ("mwifiex: printk() overflow with 32-byte
SSIDs"), we failed to account for the existence of 32-char SSIDs in our
debugfs code. Unlike in that case though, we zeroed out the containing
struct first, and I'm pretty sure we're guaranteed to have some padding
after the 'ssid.ssid' and 'ssid.ssid_len' fields (the struct is 33 bytes
long).
So, this is the difference between:
# cat /sys/kernel/debug/mwifiex/mlan0/info
...
essid="0123456789abcdef0123456789abcdef "
...
and the correct output:
# cat /sys/kernel/debug/mwifiex/mlan0/info
...
essid="0123456789abcdef0123456789abcdef"
...
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b05c73bd1e upstream.
Allocate buffers on HEAP instead of STACK for local structures
that are to be sent using usb_control_msg().
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d6fa57b4d upstream.
While this may appear as a humdrum one line change, it's actually quite
important. An sk_buff stores data in three places:
1. A linear chunk of allocated memory in skb->data. This is the easiest
one to work with, but it precludes using scatterdata since the memory
must be linear.
2. The array skb_shinfo(skb)->frags, which is of maximum length
MAX_SKB_FRAGS. This is nice for scattergather, since these fragments
can point to different pages.
3. skb_shinfo(skb)->frag_list, which is a pointer to another sk_buff,
which in turn can have data in either (1) or (2).
The first two are rather easy to deal with, since they're of a fixed
maximum length, while the third one is not, since there can be
potentially limitless chains of fragments. Fortunately dealing with
frag_list is opt-in for drivers, so drivers don't actually have to deal
with this mess. For whatever reason, macsec decided it wanted pain, and
so it explicitly specified NETIF_F_FRAGLIST.
Because dealing with (1), (2), and (3) is insane, most users of sk_buff
doing any sort of crypto or paging operation calls a convenient function
called skb_to_sgvec (which happens to be recursive if (3) is in use!).
This takes a sk_buff as input, and writes into its output pointer an
array of scattergather list items. Sometimes people like to declare a
fixed size scattergather list on the stack; othertimes people like to
allocate a fixed size scattergather list on the heap. However, if you're
doing it in a fixed-size fashion, you really shouldn't be using
NETIF_F_FRAGLIST too (unless you're also ensuring the sk_buff and its
frag_list children arent't shared and then you check the number of
fragments in total required.)
Macsec specifically does this:
size += sizeof(struct scatterlist) * (MAX_SKB_FRAGS + 1);
tmp = kmalloc(size, GFP_ATOMIC);
*sg = (struct scatterlist *)(tmp + sg_offset);
...
sg_init_table(sg, MAX_SKB_FRAGS + 1);
skb_to_sgvec(skb, sg, 0, skb->len);
Specifying MAX_SKB_FRAGS + 1 is the right answer usually, but not if you're
using NETIF_F_FRAGLIST, in which case the call to skb_to_sgvec will
overflow the heap, and disaster ensues.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f555f34fdc ]
The Ethernet link on an interrupt driven PHY was not coming up if the Ethernet
cable was plugged before the Ethernet interface was brought up.
The patch trigger PHY state machine to update link state if PHY was requested to
do auto-negotiation and auto-negotiation complete flag already set.
During power-up cycle the PHY do auto-negotiation, generate interrupt and set
auto-negotiation complete flag. Interrupt is handled by PHY state machine but
doesn't update link state because PHY is in PHY_READY state. After some time
MAC bring up, start and request PHY to do auto-negotiation. If there are no new
settings to advertise genphy_config_aneg() doesn't start PHY auto-negotiation.
PHY continue to stay in auto-negotiation complete state and doesn't fire
interrupt. At the same time PHY state machine expect that PHY started
auto-negotiation and is waiting for interrupt from PHY and it won't get it.
Fixes: 321beec504 ("net: phy: Use interrupts when available in NOLINK state")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Cc: stable <stable@vger.kernel.org> # v4.9+
Tested-by: Roger Quadros <rogerq@ti.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6478218e6 ]
When a parent macvlan device is destroyed we end up purging its
broadcast queue without dropping the device reference count on
the packet source device. This causes the source device to linger.
This patch drops that reference count.
Fixes: 260916dfb4 ("macvlan: Fix potential use-after free for...")
Reported-by: Joe Ghalam <Joe.Ghalam@dell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e82c9e4ed ]
Handler for ETHTOOL_GRXCLSRLALL must set info->data to the size
of the table, regardless of the amount of entries in it.
Existing code does not do that, and this breaks all usage of ethtool -N
or -n without explicit location, with this error:
rmgr: Invalid RX class rules table size: Success
Set info->data to the table size.
Tested:
ethtool -n ens8
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1 loc 55
ethtool -n ens8
ethtool -N ens8 delete 1023
ethtool -N ens8 delete 55
Fixes: f913a72aa0 ("net/mlx5e: Add support to get ethtool flow rules")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
