commit 06e1a5cc57 upstream.
The manufacturing information is stored in the EEPROM. This chip
is an AT24C64 not not (nor has it ever been) 24C02. This patch will
correctly address the EEPROM to read the entire contents and not just
256 bytes (of 0xff).
Fixes: 5e3447a29a ("ARM: dts: LogicPD Torpedo: Add AT24 EEPROM Support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8581c7c8b upstream.
The board file for imx6sx-sdb overrides cpufreq operating points to use
higher voltages. This is done because the board has a shared rail for
VDD_ARM_IN and VDD_SOC_IN and when using LDO bypass the shared voltage
needs to be a value suitable for both ARM and SOC.
This only applies to LDO bypass mode, a feature not present in upstream.
When LDOs are enabled the effect is to use higher voltages than necessary
for no good reason.
Setting these higher voltages can make some boards fail to boot with ugly
semi-random crashes reminiscent of memory corruption. These failures only
happen on board rev. C, rev. B is reported to still work.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 54183bd7f7 ("ARM: imx6sx-sdb: add revb board and make it default")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3df1ec063 upstream.
Remove ADC channels that are not available by default on the sama5d3_xplained
board (resistor not populated) in order to not create confusion.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cdd31e591 upstream.
The voltage reference for the ADC is not 3V but 3.3V since it is connected to
VDDANA.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cdefd5b54 upstream.
The CPU port of the BCM53125 is configured with RGMII (no delays) but
this should actually be RGMII with transmit delay (rgmii-txid) because
STMMAC takes care of inserting the transmitter delay. This fixes
occasional packet loss encountered.
Fixes: d7b9eaff5f ("ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acfa28b364 upstream.
The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06dbf468a2 upstream.
The ipq board has these rates as 25MHz, and not 19.2 and 27. I
copy/pasted from other boards that have those rates but forgot
to fix the rates here.
Fixes: 30fc4212d5 ("arm: dts: qcom: Add more board clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8413299cb3 ]
Since v4.10-rc1, the following logs appears in loop :
[ 801.953836] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 801.960455] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 801.966611] usb usb6-port1: cannot disable (err = -32)
[ 806.083772] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 806.090370] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 806.096494] usb usb6-port1: cannot disable (err = -32)
After analysis, xhci try to set link in U3 and returns an error.
Using snps,dis_u3_susphy_quirk fix this issue.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c2bf9f959 upstream.
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e10889a31 upstream.
This reverts commit cab4328268 ("ARM: at91/dt: sama5d2: Use new
compatible for ohci node")
It depends from commit 7150bc9b4d ("usb: ohci-at91: Forcibly suspend
ports while USB suspend") which was reverted and implemented
differently. With the new implementation, the compatible string must
remain the same.
The compatible string introduced by this commit has been used in the
default SAMA5D2 dtsi starting from Linux 4.8. As it has never been
working correctly in an official release, removing it should not be
breaking the stability rules.
Fixes: cab4328268 ("ARM: at91/dt: sama5d2: Use new compatible for ohci node")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78162d4846 upstream.
Enable DMA on uart1 to get a more reliable console.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef8d02d4a2 upstream.
Enable DMA on usart3 to get a more reliable console. This is especially
useful for automation and kernelci were a kernel with PROVE_LOCKING enabled
is quite susceptible to character loss, resulting in tests failure.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f59b31911 upstream.
GPIO4_11 is on pin 152(MX6DL_PAD_KEY_ROW2) and not on pin
151(MX6DL_PAD_KEY_ROW1).
I found the error while booting a mainline kernel on APF6S SoM and
noticed the following message:
[ 2.609337] imx6dl-pinctrl 20e0000.iomuxc: pin MX6DL_PAD_KEY_ROW1
already requested by 20a8000.gpio:105; cannot claim for 20a8000.gpio:107
[ 2.621884] imx6dl-pinctrl 20e0000.iomuxc: pin-151 (20a8000.gpio:107)
status -22
[ 2.629303] spi_imx 2008000.ecspi: Can't get CS GPIO 107
With this patch, the message is gone and spi_imx driver probes correctly.
Fixes: bb728d662b ("ARM: dts: add gpio-ranges property to iMX GPIO controllers")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ea6af3216 upstream.
This fixes commit ab8dd3aed0 ("ARM: DTS: Add minimal Support for
Logic PD DM3730 SOM-LV") where the Card Detect and Write Protect
pins were improperly configured.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ab5c2b662 upstream.
This patch fixes the following error:
sgtl5000 0-000a: Error reading chip id -6
imx-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
imx-sgtl5000 sound: snd_soc_register_card failed (-517)
The problem was that the pinctrl group was linked to the sound driver
instead of the codec node. Since the codec is probed first, the sys_mclk
was missing and it would therefore fail to initialize.
Fixes: b32e700256 ("ARM: dts: imx: add Boundary Devices Nitrogen6_Max board")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d37d41a14 upstream.
Commit d1f3156fc8 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: d1f3156fc8 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23ab4c6183 upstream.
Commit 008a2ebcd6 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 008a2ebcd6 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce95077d0c upstream.
Commit 75813028bb ("ARM: dts: am4372: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 75813028bb ("ARM: dts: am4372: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9faa84cb9 upstream.
Commit 76a8548ea9 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76a8548ea9 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c565d1a63 upstream.
Commit da6269e7e3 ("ARM: dts: omap4: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: da6269e7e3 ("ARM: dts: omap4: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d8d6d3f2f upstream.
Commit f8bf01611c ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: f8bf01611c ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9536fd30d4 upstream.
Commit 76155b378c ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76155b378c ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ed80b3a23 upstream.
Commit 06bfb9c199 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 06bfb9c199 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f6c857b12 upstream.
Commit 55871eb6e2 ("ARM: dts: dra7: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 55871eb6e2 ("ARM: dts: dra7: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43849785e1 upstream.
Read access to the SPI flash are broken on da850-evm, i.e. the data
read is not what is actually programmed on the flash.
According to the datasheet for the M25P64 part present on the da850-evm,
if the SPI frequency is higher than 20MHz then the READ command is not
usable anymore and only the FAST_READ command can be used to read data.
This commit specifies in the DTS that we should use FAST_READ command
instead of the READ command.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
commit 87cb12910a upstream.
AHCI provides the register PORTS_IMPL to let the software know which port
is supported. The register must be initialized by the bootloader. However
in some cases u-boot doesn't properly initialize this value (if it is not
compiled with SATA support for example or if the SATA initialization fails).
The DTS entry "ports-implemented" can be used to override the value in
PORTS_IMPL.
Without this patch the SATA will not work in the following two cases:
* if there has been a failure to initialize SATA in u-boot.
* if ahci_platform module has been removed and re-inserted. The reason is
that the content of PORTS_IMPL is lost after the module is removed.
I suspect that it's because the controller is reset by the hwmod.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated comments with what goes wrong]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7245f67f86 upstream.
Fixes: ("ab8dd3aed0 ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
This adds the dts file into the Makefile. This should have been included in
the original patch.
V2: Update patch description - same source code
V1: Original patch
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af92305e56 upstream.
On i.MX31 AVIC interrupt controller base address is at 0x68000000.
The problem was shadowed by the AVIC driver, which takes the correct
base address from a SoC specific header file.
Fixes: d2a37b3d91 ("ARM i.MX31: Add devicetree support")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f87aee6a2 upstream.
i.MX31 Clock Control Module controller is found on AIPS2 bus, move it
there from SPBA bus to avoid a conflict of device IO space mismatch.
Fixes: ef0e4a606f ("ARM: mx31: Replace clk_register_clkdev with clock DT lookup")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e575cbc93 upstream.
The type of AVIC interrupt controller found on i.MX31 is one-cell,
namely 31 for CCM DVFS and 53 for CCM, however for clock control
module its interrupts are specified as 3-cells, fix it.
Fixes: ef0e4a606f ("ARM: mx31: Replace clk_register_clkdev with clock DT lookup")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72649a4606 upstream.
According to the schematics of CompuLab's sbc-fx6 baseboard and the
vendor devicetree GPIO_16 is *not* muxed to ENET_REF_CLK but to SPDIF_IN.
Remove the wrong pinctrl setting.
Fixes: 682d055e6a ("ARM: dts: Add initial support for cm-fx6.")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d891a685d upstream.
The address of the mailbox node in the bcm283x.dtsi also has a typo.
So fix it accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Fixes: 05b682b7a3 ("ARM: bcm2835: dt: Add the mailbox to the device tree")
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cff18cbab upstream.
The 2 USB host ports are directly tied to the 2 USB hosts in the SoC.
The 2 host pairs were already enabled, but the USB PHY wasn't.
VBUS on the 2 ports are always on.
Enable the USB PHY.
Fixes: 04c85ecad3 ("ARM: dts: sun7i: Add dts file for Bananapi M1 Plus
board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc8ee9dbdb upstream.
The parent clock of the HSUSB clock is the HP clock, not the MP clock.
Fixes: c7bab9f929 ("ARM: shmobile: r8a7794: Add USB clocks to device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bug report from Debian [0] shows there's minor changed model of
Linkstation LS-GL that uses the 2nd SATA port of the SoC.
So it's necessary to enable two SATA ports, though for that specific
model only the 2nd one is used.
[0] https://bugs.debian.org/845611
Fixes: b1742ffa9d ("ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl")
Reported-by: Ryan Tandy <ryan@nardis.ca>
Tested-by: Ryan Tandy <ryan@nardis.ca>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The eLCDIF IP of the i.MX 7 SoC knows multiple clocks and lists them
separately:
Clock Clock Root Description
apb_clk MAIN_AXI_CLK_ROOT AXI clock
pix_clk LCDIF_PIXEL_CLK_ROOT Pixel clock
ipg_clk_s MAIN_AXI_CLK_ROOT Peripheral access clock
All of them are switched by a single gate, which is part of the
IMX7D_LCDIF_PIXEL_ROOT_CLK clock. Hence using that clock also for
the AXI bus clock (clock-name "axi") makes sure the gate gets
enabled when accessing registers.
There seem to be no separate AXI display clock, and the clock is
optional. Hence remove the dummy clock.
This fixes kernel freezes when starting the X-Server (which
disables/re-enables the display controller).
Fixes: e8ed73f691 ("ARM: dts: imx7d: add lcdif support")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
In a previous commit, I made a copy/paste error in the pinmux
definitions of UART3: PG{13,14} instead of PA{13,14}. This commit takes
care of that. I have tested this commit on Orange Pi PC and Orange Pi
Plus, and it works for these boards.
Fixes: e3d11d3c45 ("dts: sun8i-h3: add pinmux definitions for
UART2-3")
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The I2C nodes are missing #address-cells and #size-cells.
This is causing warning at device tree compilation when
some I2C device sub-nodes are defined.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nQve
-----END PGP SIGNATURE-----
Merge tag 'sti-dt-for-v4.9-rc-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into fixes
Pull "STi DT fix" from Patrice Chotard:
The I2C nodes are missing #address-cells and #size-cells.
This is causing warning at device tree compilation when
some I2C device sub-nodes are defined.
* tag 'sti-dt-for-v4.9-rc-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH407-family: fix i2c nodes
A renaming of the GR8 DTSI and DTS to make it explicitly part of the sun5i
family.
-----BEGIN PGP SIGNATURE-----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=Mw6R
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.9-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Pull "Allwinner fixes for 4.9, second iteration" from Maxime Ripard:
A renaming of the GR8 DTSI and DTS to make it explicitly part of the sun5i
family.
* tag 'sunxi-fixes-for-4.9-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: gr8: Rename the DTSI and relevant DTS
The I2C nodes are missing #address-cells and #size-cells. This is
causing warning at device tree compilation when some I2C device
sub-nodes are defined.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Reviews have found that sun5i was a better prefix after all for the GR8.
Rename the relevant device trees before it's too late.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A fix to reintroduce missing pinmux options that turned out not to be
optional.
-----BEGIN PGP SIGNATURE-----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=WBs5
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.9
A fix to reintroduce missing pinmux options that turned out not to be
optional.
* tag 'sunxi-fixes-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun8i: fix the pinmux for UART1
Signed-off-by: Olof Johansson <olof@lixom.net>
It fixes a boot failure on imx53-qsb board with a DA9053 PMIC, which is
caused by the regulator core change, commit fa93fd4ecc ("regulator:
core: Ensure we are at least in bounds for our constraints").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYKnQ1AAoJEFBXWFqHsHzOyEYH/0F1TKtmJwLeDBKBinmeG0wx
IX/0mXCV0E72T7W6PuifofG7H9jax9UY8qGyDl9+h/dMBQCaKPfXDo6wg5FoXaBe
UAQVHbRbEuazI2xW0UWeiywt6soGBe1/iNpt+OXXfmJY77vS5nuGfFCLGey6+uTe
WeGi3J6g2Oxa65FndvfTm5dNj6vCa3VHs5UKQKCId3KoTjuLZu4EUrN81e47tkmJ
pmzaGBfAUyvACfwkITzc6rAbBp29FtxMK52ieuh+w4L3DWa3kpCabHPMIAeP8C9P
GQ80PTyfs/F163yYM6dWRipwhz/XJhjtT8SWBG/hnYBJDEHOua4uqW3YcoNdm7E=
=xunY
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.9, 2nd round:
It fixes a boot failure on imx53-qsb board with a DA9053 PMIC, which is
caused by the regulator core change, commit fa93fd4ecc ("regulator:
core: Ensure we are at least in bounds for our constraints").
* tag 'imx-fixes-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx53-qsb: Fix regulator constraints
Signed-off-by: Olof Johansson <olof@lixom.net>
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
-----BEGIN PGP SIGNATURE-----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=LgIW
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.9-rc cycle. Except for the omap3 fix for the SoC
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
* tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
Signed-off-by: Olof Johansson <olof@lixom.net>
DDR3L is usually specified as
JEDEC standard 1.35V(1.28V~1.45V) & 1.5V(1.425V~1.575V)
Therefore setting smps6 regulator to 1.2V is definitively below
minimum. It appears that real world chips are more forgiving than
data sheets indicate, but let's set the regulator right.
Note: a board that uses other voltages (DDR with 1.5V) can
overwrite by referencing &smps6_reg.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
