[ Upstream commit cd60be4916 ]
Set variables initialized in lpfc_sli4_alloc_resource_identifiers() to
NULL if an error occurred. Otherwise, lpfc_sli4_driver_resource_unset()
attempts to free the memory again.
Signed-off-by: Roberto Sassu <rsassu@suse.de>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 773c7220e2 ]
In the case of a graceful set of detaches, where the virtio-scsi-ccw
disk is removed from the guest prior to the controller, the guest
behaves quite normally. Specifically, the detach gets us into
sd_sync_cache to issue a Synchronize Cache(10) command, which
immediately fails (and is retried a couple of times) because the device
has been removed. Later, the removal of the controller sees two CRWs
presented, but there's no further indication of the removal from the
guest viewpoint.
[ 17.217458] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 17.219257] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 21.449400] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
[ 21.449406] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0
However, on s390, the SCSI disks can be removed "by surprise" when an
entire controller (host) is removed and all associated disks are removed
via the loop in scsi_forget_host. The same call to sd_sync_cache is
made, but because the controller has already been removed, the
Synchronize Cache(10) command is neither issued (and then failed) nor
rejected.
That the I/O isn't returned means the guest cannot have other devices
added nor removed, and other tasks (such as shutdown or reboot) issued
by the guest will not complete either. The virtio ring has already been
marked as broken (via virtio_break_device in virtio_ccw_remove), but we
still attempt to queue the command only to have it remain there. The
calling sequence provides a bit of distinction for us:
virtscsi_queuecommand()
-> virtscsi_kick_cmd()
-> virtscsi_add_cmd()
-> virtqueue_add_sgs()
-> virtqueue_add()
if success
return 0
elseif vq->broken or vring_mapping_error()
return -EIO
else
return -ENOSPC
A return of ENOSPC is generally a temporary condition, so returning
"host busy" from virtscsi_queuecommand makes sense here, to have it
redriven in a moment or two. But the EIO return code is more of a
permanent error and so it would be wise to return the I/O itself and
allow the calling thread to finish gracefully. The result is these four
kernel messages in the guest (the fourth one does not occur prior to
this patch):
[ 22.921562] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
[ 22.921580] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0
[ 22.921978] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 22.921993] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
I opted to fill in the same response data that is returned from the more
graceful device detach, where the disk device is removed prior to the
controller device.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f060736f2 ]
Termination of Immediate Notify IOCB was using wrong
IOCB handle. IOCB completion code was unable to find
appropriate code path due to wrong handle.
Following message is seen in the logs.
"Error entry - invalid handle/queue (ffff)."
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed word order in patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f35509db1 ]
Corrupted ATIO is defined as length of fcp_header & fcp_cmd
payload is less than 0x38. It's the minimum size for a frame to
carry 8..16 bytes SCSI CDB. The exchange will be dropped or
terminated if corrupted.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8667f51595 ]
Set the elsiocb contexts to NULL after freeing as others depend on it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26f2819772 ]
Zoned block devices force the use of READ/WRITE(16) commands by setting
sdkp->use_16_for_rw and clearing sdkp->use_10_for_rw. This result in
DPOFUA always being disabled for these drives as the assumed use of
the deprecated READ/WRITE(6) commands only looks at sdkp->use_10_for_rw.
Strenghten the test by also checking that sdkp->use_16_for_rw is false.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d63496516 upstream.
Set bit (BIT_15) to send right ECHO payload information for Diagnostic
Echo Test command.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddff7ed45e upstream.
When pci_enable_device() or pci_enable_device_mem() fail in
qla2x00_probe_one() we bail out but do a call to
pci_disable_device(). This causes the dev_WARN_ON() in
pci_disable_device() to trigger, as the device wasn't enabled
previously.
So instead of taking the 'probe_out' error path we can directly return
*iff* one of the pci_enable_device() calls fails.
Additionally rename the 'probe_out' goto label's name to the more
descriptive 'disable_device'.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: e315cd28b9 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring")
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2e767bb5d upstream.
The firmware or device, possibly under a heavy I/O load, can return on a
partial unaligned boundary. Scsi-ml expects these requests to be
completed on an alignment boundary. Scsi-ml blindly requeues the I/O
without checking the alignment boundary of the I/O request for the
remaining bytes. This leads to errors, since devices cannot perform
non-aligned read/write operations.
This patch fixes the issue in the driver. It aligns unaligned
completions of FS requests, by truncating them to the nearest alignment
boundary.
[mkp: simplified if statement]
Reported-by: Mauricio Faria De Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75dbf2d36f upstream.
The current code is not correctly calculating the req_lim_delta.
We want to make sure vscsi->credit is always incremented when
we do not send a response for the scsi op. Thus for the case where
there is a successfully aborted task we need to make sure the
vscsi->credit is incremented.
v2 - Moves the original location of the vscsi->credit increment
to a better spot. Since if we increment credit, the next command
we send back will have increased req_lim_delta. But we probably
shouldn't be doing that until the aborted cmd is actually released.
Otherwise the client will think that it can send a new command, and
we could find ourselves short of command elements. Not likely, but could
happen.
This patch depends on both:
commit 25e7853126 ("ibmvscsis: Do not send aborted task response")
commit 98883f1b54 ("ibmvscsis: Clear left-over abort_cmd pointers")
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Reviewed-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98883f1b54 upstream.
With the addition of ibmvscsis->abort_cmd pointer within
commit 25e7853126 ("ibmvscsis: Do not send aborted task response"),
make sure to explicitly NULL these pointers when clearing
DELAY_SEND flag.
Do this for two cases, when getting the new new ibmvscsis
descriptor in ibmvscsis_get_free_cmd() and before posting
the response completion in ibmvscsis_send_messages().
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Reviewed-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25e7853126 upstream.
The driver is sending a response to the actual scsi op that was
aborted by an abort task TM, while LIO is sending a response to
the abort task TM.
ibmvscsis_tgt does not send the response to the client until
release_cmd time. The reason for this was because if we did it
at queue_status time, then the client would be free to reuse the
tag for that command, but we're still using the tag until the
command is released at release_cmd time, so we chose to delay
sending the response until then. That then caused this issue, because
release_cmd is always called, even if queue_status is not.
SCSI spec says that the initiator that sends the abort task
TM NEVER gets a response to the aborted op and with the current
code it will send a response. Thus this fix will remove that response
if the CMD_T_ABORTED && !CMD_T_TAS.
Another case with a small timing window is the case where if LIO sends a
TMR_DOES_NOT_EXIST, and the release_cmd callback is called for the TMR Abort
cmd before the release_cmd for the (attemped) aborted cmd, then we need to
ensure that we send the response for the (attempted) abort cmd to the client
before we send the response for the TMR Abort cmd.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed10858ead upstream.
When we have turned off RTC support, the smartpqi driver fails to build:
ERROR: "rtc_time64_to_tm" [drivers/scsi/smartpqi/smartpqi.ko] undefined!
This is easily avoided by using the generic 'struct tm' based helper rather
than the RTC specific one. While fixing this, I noticed that even though
the driver uses time64_t for storing seconds, it gets them from the
old 32-bit struct timeval. To address this, we can simplify the code
by calling ktime_get_real_seconds() directly.
Fixes: 6c223761eb ("smartpqi: initial commit of Microsemi smartpqi driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2559a1ef68 upstream.
The mac_scsi driver still gets disabled when SCSI=m. This should have
been fixed back when I enabled the tristate but I didn't see the bug.
Fixes: 6e9ae6d560 ("[PATCH] mac_scsi: Add module option to Kconfig")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f7c2beef8 upstream.
After a Qlogic card breaks when initializing (test case), the system can
crash in qla2xxx_eh_abort if processing anything but a scsi command type
srb.
Fixes: 1535aa75a3 ("scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove")
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-By: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1c635b439 upstream.
Hyper-V host emulation of SCSI for virtual DVD device reports SCSI
version 0 (UNKNOWN) but is still capable of supporting REPORTLUN.
Without this patch, a GEN2 Linux guest on Hyper-V will not boot 4.11
successfully with virtual DVD ROM device. What happens is that the SCSI
scan process falls back to doing sequential probing by INQUIRY. But the
storvsc driver has a previous workaround that masks/blocks all errors
reports from INQUIRY (or MODE_SENSE) commands. This workaround causes
the scan to then populate a full set of bogus LUN's on the target and
then sends kernel spinning off into a death spiral doing block reads on
the non-existent LUNs.
By setting the correct blacklist flags, the target with the DVD device
is scanned with REPORTLUN and that works correctly.
Patch needs to go in current 4.11, it is safe but not necessary in older
kernels.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c856152cb upstream.
We previously made sure that the reported disk capacity was less than
0xffffffff blocks when the kernel was not compiled with large sector_t
support (CONFIG_LBDAF). However, this check assumed that the capacity
was reported in units of 512 bytes.
Add a sanity check function to ensure that we only enable disks if the
entire reported capacity can be expressed in terms of sector_t.
Reported-by: Steve Magnani <steve.magnani@digidescorp.com>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf6061b17a upstream.
Add fix to read correct register value for ISP82xx, during check for
register disconnect.ISP82xx has different base register.
Fixes: a465537ad1 ("qla2xxx: Disable the adapter and skip error recovery in case of register disconnect")
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6780414519 upstream.
If device reports a small max_xfer_blocks and a zero opt_xfer_blocks, we
end up using BLK_DEF_MAX_SECTORS, which is wrong and r/w of that size
may get error.
[mkp: tweaked to avoid setting rw_max twice and added typecast]
Fixes: ca369d51b3 ("block/sd: Fix device-imposed transfer length limits")
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a00a786251 upstream.
Kefeng Wang discovered that old versions of the QEMU CD driver would
return mangled mode data causing us to walk off the end of the buffer in
an attempt to parse it. Sanity check the returned mode sense data.
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7caf489b99 ]
If we issue the link startup to the device while its UniPro state is
LinkDown (and device state is sleep/power-down) then link startup
will not move the device state to Active. Device will only move to
active state if the link starup is issued when its UniPro state is
LinkUp. So in this case, we would have to issue the link startup 2
times to make sure that device moves to active state.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 141f816510 ]
Add a new ufshcd_state, indicats that an err handler may get to run
immediately. Use UFSHCD_STATE_ERROR here looks not literaly correct.
Signed-off-by: Zang Leigang <zangleigang@hisilicon.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56d4a1866d ]
The maximum value PA_SaveConfigTime is 250 (10us) but this is not enough
for some vendors. Gear switch from PWM to HS may fail even with this
max. PA_SaveConfigTime. Gear switch can be issued by host controller as
an error recovery and any software delay will not help on this case so
we need to increase PA_SaveConfigTime to >32us as per vendor
recommendation. This change adds a quirk to increase the
PA_SaveConfigTime parameter.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c6a6db4398 ]
Some UFS devices require host PA_TACTIVATE to be higher than
device PA_TACTIVATE otherwise it may get stuck during hibern8 sequence.
This change allows this by using quirk.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75b1cc4ad6 ]
Some UFS host controllers may think granularities of PRDT length and
offset as bytes, not double words.
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cb689fe42 upstream.
Callers of scsi_dh_activate(), e.g. dm-mpath, assume that this function
either returns an error code or calls the completion function. Make
alua_activate() call the completion function even if scsi_device_get()
fails.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9702c67c60 upstream.
The total ata xfer length may not be calculated properly, in that we do
not use the proper method to get an sg element dma length.
According to the code comment, sg_dma_len() should be used after
dma_map_sg() is called.
This issue was found by turning on the SMMUv3 in front of the hisi_sas
controller in hip07. Multiple sg elements were being combined into a
single element, but the original first element length was being use as
the total xfer length.
Fixes: ff2aeb1eb6 ("libata: convert to chained sg")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf33f87dd0 upstream.
The user can control the size of the next command passed along, but the
value passed to the ioctl isn't checked against the usable max command
size.
Signed-off-by: Peter Chang <dpf@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f8830f5bb upstream.
There's a rather long standing regression from the commit "libiscsi:
Reduce locking contention in fast path"
Depending on iSCSI target behavior, it's possible to hit the case in
iscsi_complete_task where the task is still on a pending list
(!list_empty(&task->running)). When that happens the task is removed
from the list while holding the session back_lock, but other task list
modification occur under the frwd_lock. That leads to linked list
corruption and eventually a panicked system.
Rather than back out the session lock split entirely, in order to try
and keep some of the performance gains this patch adds another lock to
maintain the task lists integrity.
Major enterprise supported kernels have been backing out the lock split
for while now, thanks to the efforts at IBM where a lab setup has the
most reliable reproducer I've seen on this issue. This patch has been
tested there successfully.
Signed-off-by: Chris Leech <cleech@redhat.com>
Fixes: 659743b02c ("[SCSI] libiscsi: Reduce locking contention in fast path")
Reported-by: Prashantha Subbarao <psubbara@us.ibm.com>
Reviewed-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85e8a23936 upstream.
We see lpfc devices regularly fail during kexec. Fix this by adding a
shutdown method which mirrors the remove method.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b666809e1 upstream.
When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8bf11557d4 ]
This patch adds code to disconnect from the client, which will make sure
any outstanding commands have been completed, before continuing on with
the remove operation.
Signed-off-by: Michael Cyr <mikecyr@us.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9b3379f60 ]
This patch changes the way the IBM vSCSI server driver manages its
Command/Response Queue (CRQ). We used to register the CRQ with phyp at
probe time. Now we wait until tpg_enable_store. Similarly, when
tpg_enable_store is called to "disable" (i.e. the stored value is 0),
we unregister the queue with phyp.
One consquence to this is that we have no need for the PART_UP_WAIT_ENAB
state, since we can't get an Init Message from the client in our CRQ if
we're waiting to be enabled, since we haven't registered the queue yet.
Signed-off-by: Michael Cyr <mikecyr@us.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 79fac9c9b7 ]
This patch reorders functions in a manner necessary for a follow-on
patch. It also makes some minor styling changes (mostly removing extra
spaces) and fixes some typos.
There are no code changes in this patch, with one exception: due to the
reordering of the functions, I needed to explicitly declare a function
at the top of the file. However, this will be removed in the next patch,
since the code requiring the predeclaration will be removed.
Signed-off-by: Michael Cyr <mikecyr@us.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ea73db486 upstream.
Correct WQ creation for pagesize
The driver was calculating the adapter command pagesize indicator from
the system pagesize. However, the buffers the driver allocates are only
one size (SLI4_PAGE_SIZE), so no calculation was necessary.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 857de6e007 upstream.
The device handler needs to check if a given queue belongs to a scsi
device; only then does it make sense to attach a device handler.
[mkp: dropped flags]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c421530bf8 upstream.
The driver currently checks the SELF_TEST_FAILED first and then
KERNEL_PANIC next. Under error conditions(boot code failure) both
SELF_TEST_FAILED and KERNEL_PANIC can be set at the same time.
The driver has the capability to reset the controller on an KERNEL_PANIC,
but not on SELF_TEST_FAILED.
Fixed by first checking KERNEL_PANIC and then the others.
Fixes: e8b12f0fb8 ([SCSI] aacraid: Add new code for PMC-Sierra's SRC base controller family)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40630f4628 upstream.
On I/O errors, the Windows driver doesn't set data_transfer_length
on error conditions other than SRB_STATUS_DATA_OVERRUN.
In these cases we need to set data_transfer_length to 0,
indicating there is no data transferred. On SRB_STATUS_DATA_OVERRUN,
data_transfer_length is set by the Windows driver to the actual data transferred.
Reported-by: Shiva Krishna <Shiva.Krishna@nimblestorage.com>
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bba5dc332e upstream.
When sense message is present on error, we should pass along to the upper
layer to decide how to deal with the error.
This patch fixes connectivity issues with Fiber Channel devices.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cd6d3d9b1 upstream.
Properly set SRB flags when hosting device supports tagged queuing.
This patch improves the performance on Fiber Channel disks.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 137d01df51 upstream.
What happens is that a write to /dev/sg is given a request with non-zero
->iovec_count combined with zero ->dxfer_len. Or with ->dxferp pointing
to an array full of empty iovecs.
Having write permission to /dev/sg shouldn't be equivalent to the
ability to trigger BUG_ON() while holding spinlocks...
Found by Dmitry Vyukov and syzkaller.
[ The BUG_ON() got changed to a WARN_ON_ONCE(), but this fixes the
underlying issue. - Linus ]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd3fc0b4d7 upstream.
Don't crash the machine just because of an empty transfer. Use WARN_ON()
combined with returning an error.
Found by Dmitry Vyukov and syzkaller.
[ Changed to "WARN_ON_ONCE()". Al has a patch that should fix the root
cause, but a BUG_ON() is not acceptable in any case, and a WARN_ON()
might still be a cause of excessive log spamming.
NOTE! If this warning ever triggers, we may end up leaking resources,
since this doesn't bother to try to clean the command up. So this
WARN_ON_ONCE() triggering does imply real problems. But BUG_ON() is
much worse.
People really need to stop using BUG_ON() for "this shouldn't ever
happen". It makes pretty much any bug worse. - Linus ]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
