commit f06b7549b7 upstream.
Lennert reported a failure to add different mpls encaps in a multipath
route:
$ ip -6 route add 1234::/16 \
nexthop encap mpls 10 via fe80::1 dev ens3 \
nexthop encap mpls 20 via fe80::1 dev ens3
RTNETLINK answers: File exists
The problem is that the duplicate nexthop detection does not compare
lwtunnel configuration. Add it.
Fixes: 19e42e4515 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Reported-by: João Taveira Araújo <joao.taveira@gmail.com>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec8add2a4c upstream.
Currently, when the link for $DEV is down, this command succeeds but the
address is removed immediately by DAD (1):
ip addr add 1111::12/64 dev $DEV valid_lft 3600 preferred_lft 1800
In the same situation, this will succeed and not remove the address (2):
ip addr add 1111::12/64 dev $DEV
ip addr change 1111::12/64 dev $DEV valid_lft 3600 preferred_lft 1800
The comment in addrconf_dad_begin() when !IF_READY makes it look like
this is the intended behavior, but doesn't explain why:
* If the device is not ready:
* - keep it tentative if it is a permanent address.
* - otherwise, kill it.
We clearly cannot prevent userspace from doing (2), but we can make (1)
work consistently with (2).
addrconf_dad_stop() is only called in two cases: if DAD failed, or to
skip DAD when the link is down. In that second case, the fix is to avoid
deleting the address, like we already do for permanent addresses.
Fixes: 3c21edbd11 ("[IPV6]: Defer IPv6 device initialization until the link becomes ready.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60abc0be96 upstream.
The per netns loopback_dev->ip6_ptr is unregistered and set to
NULL when its mtu is set to smaller than IPV6_MIN_MTU, this
leads to that we could set rt->rt6i_idev NULL after a
rt6_uncached_list_flush_dev() and then crash after another
call.
In this case we should just bring its inet6_dev down, rather
than unregistering it, at least prior to commit 176c39af29
("netns: fix addrconf_ifdown kernel panic") we always
override the case for loopback.
Thanks a lot to Andrey for finding a reliable reproducer.
Fixes: 176c39af29 ("netns: fix addrconf_ifdown kernel panic")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e9a709560 ]
This fix addresses two problems in the way the DSCP field is formulated
on the encapsulating header of IPv6 tunnels.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195661
1) The IPv6 tunneling code was manipulating the DSCP field of the
encapsulating packet using the 32b flowlabel. Since the flowlabel is
only the lower 20b it was incorrect to assume that the upper 12b
containing the DSCP and ECN fields would remain intact when formulating
the encapsulating header. This fix handles the 'inherit' and
'fixed-value' DSCP cases explicitly using the extant dsfield u8 variable.
2) The use of INET_ECN_encapsulate(0, dsfield) in ip6_tnl_xmit was
incorrect and resulted in the DSCP value always being set to 0.
Commit 90427ef5d2 ("ipv6: fix flow labels when the traffic class
is non-0") caused the regression by masking out the flowlabel
which exposed the incorrect handling of the DSCP portion of the
flowlabel in ip6_tunnel and ip6_gre.
Fixes: 90427ef5d2 ("ipv6: fix flow labels when the traffic class is non-0")
Signed-off-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21b995a9cb ]
Since ip6_tnl_parse_tlv_enc_lim() can call pskb_may_pull(),
we must reload any pointer that was related to skb->head
(or skb->data), or risk use after free.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07f615574f ]
While commit 73ba57bfae ("ipv6: fix backtracking for throw routes")
does good job on error propagation to the fib_rules_lookup()
in fib rules core framework that also corrects throw routes
handling, it does not solve route reference leakage problem
happened when we return -EAGAIN to the fib_rules_lookup()
and leave routing table entry referenced in arg->result.
If rule with matched throw route isn't last matched in the
list we overwrite arg->result losing reference on throw
route stored previously forever.
We also partially revert commit ab997ad408 ("ipv6: fix the
incorrect return value of throw route") since we never return
routing table entry with dst.error == -EAGAIN when
CONFIG_IPV6_MULTIPLE_TABLES is on. Also there is no point
to check for RTF_REJECT flag since it is always set throw
route.
Fixes: 73ba57bfae ("ipv6: fix backtracking for throw routes")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f8a894b218 ]
Now when starting the dad work in addrconf_mod_dad_work, if the dad work
is idle and queued, it needs to hold ifa.
The problem is there's one gap in [1], during which if the pending dad work
is removed elsewhere. It will miss to hold ifa, but the dad word is still
idea and queue.
if (!delayed_work_pending(&ifp->dad_work))
in6_ifa_hold(ifp);
<--------------[1]
mod_delayed_work(addrconf_wq, &ifp->dad_work, delay);
An use-after-free issue can be caused by this.
Chen Wei found this issue when WARN_ON(!hlist_unhashed(&ifp->addr_lst)) in
net6_ifa_finish_destroy was hit because of it.
As Hannes' suggestion, this patch is to fix it by holding ifa first in
addrconf_mod_dad_work, then calling mod_delayed_work and putting ifa if
the dad_work is already in queue.
Note that this patch did not choose to fix it with:
if (!mod_delayed_work(delay))
in6_ifa_hold(ifp);
As with it, when delay == 0, dad_work would be scheduled immediately, all
addrconf_mod_dad_work(0) callings had to be moved under ifp->lock.
Reported-by: Wei Chen <weichen@redhat.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3500cd73df ]
Reading /proc/net/snmp6 yields bogus values on 32 bit kernels.
Use "u64" instead of "unsigned long" in sizeof().
Fixes: 4a4857b1c8 ("proc: Reduce cache miss in snmp6_seq_show")
Signed-off-by: Christian Perle <christian.perle@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00ea1ceebe upstream.
If ip6_dst_lookup_tail has acquired a dst and fails the IPv4-mapped
check, release the dst before returning an error.
Fixes: ec5e3b0a1d ("ipv6: Inhibit IPv4-mapped src address on the wire.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0db47e3d32 upstream.
While discussing the possible merits of clang warning about unused initialized
functions, I found one function that was clearly meant to be called but
never actually is.
__ila_hash_secret_init() initializes the hash value for the ila locator,
apparently this is intended to prevent hash collision attacks, but this ends
up being a read-only zero constant since there is no caller. I could find
no indication of why it was never called, the earliest patch submission
for the module already was like this. If my interpretation is right, we
certainly want to backport the patch to stable kernels as well.
I considered adding it to the ila_xlat_init callback, but for best effect
the random data is read as late as possible, just before it is first used.
The underlying net_get_random_once() is already highly optimized to avoid
overhead when called frequently.
Fixes: 7f00feaf10 ("ila: Add generic ILA translation facility")
Link: https://www.spinics.net/lists/kernel/msg2527243.html
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a088d1d73a ]
When for instance a mobile Linux device roams from one access point to
another with both APs sharing the same broadcast domain and a
multicast snooping switch in between:
1) (c) <~~~> (AP1) <--[SSW]--> (AP2)
2) (AP1) <--[SSW]--> (AP2) <~~~> (c)
Then currently IPv6 multicast packets will get lost for (c) until an
MLD Querier sends its next query message. The packet loss occurs
because upon roaming the Linux host so far stayed silent regarding
MLD and the snooping switch will therefore be unaware of the
multicast topology change for a while.
This patch fixes this by always resending MLD reports when an interface
change happens, for instance from NO-CARRIER to CARRIER state.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a11a7f71ca ]
Under some circumstances it is possible that no new temporary addresses
will be generated.
For instance, addrconf_prefix_rcv_add_addr() indirectly calls
ipv6_create_tempaddr(), which creates a tentative temporary address and
starts dad. Next, addrconf_prefix_rcv_add_addr() indirectly calls
addrconf_verify_rtnl(). Now, assume that the previously created temporary
address has the least preferred lifetime among all existing addresses and
is still tentative (that is, dad is still running). Hence, the next run of
addrconf_verify_rtnl() is performed when the preferred lifetime of the
temporary address ends. If dad succeeds before the next run, the temporary
address becomes deprecated during the next run, but no new temporary
address is generated.
In order to fix this, schedule the next addrconf_verify_rtnl() run slightly
before the temporary address becomes deprecated, if dad succeeded.
Signed-off-by: Marcus Huewe <suse-tux@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ec5e3b0a1d ]
This patch adds a check for the problematic case of an IPv4-mapped IPv6
source address and a destination address that is neither an IPv4-mapped
IPv6 address nor in6addr_any, and returns an appropriate error. The
check in done before returning from looking up the route.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 052d2369d1 ]
This patch adds a check on the type of the source address for the case
where the destination address is in6addr_any. If the source is an
IPv4-mapped IPv6 source address, the destination is changed to
::ffff:127.0.0.1, and otherwise the destination is changed to ::1. This
is done in three locations to handle UDP calls to either connect() or
sendmsg() and TCP calls to connect(). Note that udpv6_sendmsg() delays
handling an in6addr_any destination until very late, so the patch only
needs to handle the case where the source is an IPv4-mapped IPv6
address.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3ebdb20fd ]
When using CALIPSO with IPPROTO_UDP it is possible to trigger a GPF as the
IP header may have moved.
Also update the payload length after adding the CALIPSO option.
Signed-off-by: Richard Haines <richard_c_haines@btinternet.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77d4b1d369 ]
Alexander reported various KASAN messages triggered in recent kernels
The problem is that ping sockets should not use udp_poll() in the first
place, and recent changes in UDP stack finally exposed this old bug.
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Fixes: 6d0bfe2261 ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sasha Levin <alexander.levin@verizon.com>
Cc: Solar Designer <solar@openwall.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Acked-By: Lorenzo Colitti <lorenzo@google.com>
Tested-By: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3e86b5119 ]
If ip6_find_1stfragopt() fails and we return an error we have to free
up 'segs' because nobody else is going to.
Fixes: 2423496af3 ("ipv6: Prevent overrun when parsing v6 header options")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e80ac5cc9 ]
xfrm6_find_1stfragopt() may now return an error code and we must
not treat it as a length.
Fixes: 2423496af3 ("ipv6: Prevent overrun when parsing v6 header options")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 232cd35d08 ]
Andrey Konovalov and idaifish@gmail.com reported crashes caused by
one skb shared_info being overwritten from __ip6_append_data()
Andrey program lead to following state :
copy -4200 datalen 2000 fraglen 2040
maxfraglen 2040 alloclen 2048 transhdrlen 0 offset 0 fraggap 6200
The skb_copy_and_csum_bits(skb_prev, maxfraglen, data + transhdrlen,
fraggap, 0); is overwriting skb->head and skb_shared_info
Since we apparently detect this rare condition too late, move the
code earlier to even avoid allocating skb and risking crashes.
Once again, many thanks to Andrey and syzkaller team.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Reported-by: <idaifish@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7dd7eb9513 ]
Do not use unsigned variables to see if it returns a negative
error or not.
Fixes: 2423496af3 ("ipv6: Prevent overrun when parsing v6 header options")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83eaddab43 ]
Like commit 657831ffc3 ("dccp/tcp: do not inherit mc_list from parent")
we should clear ipv6_mc_list etc. for IPv6 sockets too.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 242d3a49a2 ]
For each netns (except init_net), we initialize its null entry
in 3 places:
1) The template itself, as we use kmemdup()
2) Code around dst_init_metrics() in ip6_route_net_init()
3) ip6_route_dev_notify(), which is supposed to initialize it after
loopback registers
Unfortunately the last one still happens in a wrong order because
we expect to initialize net->ipv6.ip6_null_entry->rt6i_idev to
net->loopback_dev's idev, thus we have to do that after we add
idev to loopback. However, this notifier has priority == 0 same as
ipv6_dev_notf, and ipv6_dev_notf is registered after
ip6_route_dev_notifier so it is called actually after
ip6_route_dev_notifier. This is similar to commit 2f460933f5
("ipv6: initialize route null entry in addrconf_init()") which
fixes init_net.
Fix it by picking a smaller priority for ip6_route_dev_notifier.
Also, we have to release the refcnt accordingly when unregistering
loopback_dev because device exit functions are called before subsys
exit functions.
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f460933f5 ]
Andrey reported a crash on init_net.ipv6.ip6_null_entry->rt6i_idev
since it is always NULL.
This is clearly wrong, we have code to initialize it to loopback_dev,
unfortunately the order is still not correct.
loopback_dev is registered very early during boot, we lose a chance
to re-initialize it in notifier. addrconf_init() is called after
ip6_route_init(), which means we have no chance to correct it.
Fix it by moving this initialization explicitly after
ipv6_add_dev(init_net.loopback_dev) in addrconf_init().
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d717134a1 ]
Andrey reported a warning triggered by the rcu code:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 5911 at lib/debugobjects.c:289
debug_print_object+0x175/0x210
ODEBUG: activate active (active state 1) object type: rcu_head hint:
(null)
Modules linked in:
CPU: 1 PID: 5911 Comm: a.out Not tainted 4.11.0-rc8+ #271
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x192/0x22d lib/dump_stack.c:52
__warn+0x19f/0x1e0 kernel/panic.c:549
warn_slowpath_fmt+0xe0/0x120 kernel/panic.c:564
debug_print_object+0x175/0x210 lib/debugobjects.c:286
debug_object_activate+0x574/0x7e0 lib/debugobjects.c:442
debug_rcu_head_queue kernel/rcu/rcu.h:75
__call_rcu.constprop.76+0xff/0x9c0 kernel/rcu/tree.c:3229
call_rcu_sched+0x12/0x20 kernel/rcu/tree.c:3288
rt6_rcu_free net/ipv6/ip6_fib.c:158
rt6_release+0x1ea/0x290 net/ipv6/ip6_fib.c:188
fib6_del_route net/ipv6/ip6_fib.c:1461
fib6_del+0xa42/0xdc0 net/ipv6/ip6_fib.c:1500
__ip6_del_rt+0x100/0x160 net/ipv6/route.c:2174
ip6_del_rt+0x140/0x1b0 net/ipv6/route.c:2187
__ipv6_ifa_notify+0x269/0x780 net/ipv6/addrconf.c:5520
addrconf_ifdown+0xe60/0x1a20 net/ipv6/addrconf.c:3672
...
Andrey's reproducer program runs in a very tight loop, calling
'unshare -n' and then spawning 2 sets of 14 threads running random ioctl
calls. The relevant networking sequence:
1. New network namespace created via unshare -n
- ip6tnl0 device is created in down state
2. address added to ip6tnl0
- equivalent to ip -6 addr add dev ip6tnl0 fd00::bb/1
- DAD is started on the address and when it completes the host
route is inserted into the FIB
3. ip6tnl0 is brought up
- the new fixup_permanent_addr function restarts DAD on the address
4. exit namespace
- teardown / cleanup sequence starts
- once in a blue moon, lo teardown appears to happen BEFORE teardown
of ip6tunl0
+ down on 'lo' removes the host route from the FIB since the dst->dev
for the route is loobback
+ host route added to rcu callback list
* rcu callback has not run yet, so rt is NOT on the gc list so it has
NOT been marked obsolete
5. in parallel to 4. worker_thread runs addrconf_dad_completed
- DAD on the address on ip6tnl0 completes
- calls ipv6_ifa_notify which inserts the host route
All of that happens very quickly. The result is that a host route that
has been deleted from the IPv6 FIB and added to the RCU list is re-inserted
into the FIB.
The exit namespace eventually gets to cleaning up ip6tnl0 which removes the
host route from the FIB again, calls the rcu function for cleanup -- and
triggers the double rcu trace.
The root cause is duplicate DAD on the address -- steps 2 and 3. Arguably,
DAD should not be started in step 2. The interface is in the down state,
so it can not really send out requests for the address which makes starting
DAD pointless.
Since the second DAD was introduced by a recent change, seems appropriate
to use it for the Fixes tag and have the fixup function only start DAD for
addresses in the PREDAD state which occurs in addrconf_ifdown if the
address is retained.
Big thanks to Andrey for isolating a reliable reproducer for this problem.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 105f5528b9 ]
In situations where an skb is paged, the transport header pointer and
tail pointer can be the same because the skb contents are in frags.
This results in ioctl(SIOCINQ/FIONREAD) incorrectly returning a
length of 0 when the length to receive is actually greater than zero.
skb->len is already correctly set in ip6_input_finish() with
pskb_pull(), so use skb->len as it always returns the correct result
for both linear and paged data.
Signed-off-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 199ab00f3c ]
Andrey reported a out-of-bound access in ip6_tnl_xmit(), this
is because we use an ipv4 dst in ip6_tnl_xmit() and cast an IPv4
neigh key as an IPv6 address:
neigh = dst_neigh_lookup(skb_dst(skb),
&ipv6_hdr(skb)->daddr);
if (!neigh)
goto tx_err_link_failure;
addr6 = (struct in6_addr *)&neigh->primary_key; // <=== HERE
addr_type = ipv6_addr_type(addr6);
if (addr_type == IPV6_ADDR_ANY)
addr6 = &ipv6_hdr(skb)->daddr;
memcpy(&fl6->daddr, addr6, sizeof(fl6->daddr));
Also the network header of the skb at this point should be still IPv4
for 4in6 tunnels, we shold not just use it as IPv6 header.
This patch fixes it by checking if skb->protocol is ETH_P_IPV6: if it
is, we are safe to do the nexthop lookup using skb_dst() and
ipv6_hdr(skb)->daddr; if not (aka IPv4), we have no clue about which
dest address we can pick here, we have to rely on callers to fill it
from tunnel config, so just fall to ip6_route_output() to make the
decision.
Fixes: ea3dc9601b ("ip6_tunnel: Add support for wildcard tunnel endpoints.")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8048ced9be ]
Taking down the loopback device wreaks havoc on IPv6 routing. By
extension, taking down a VRF device wreaks havoc on its table.
Dmitry and Andrey both reported heap out-of-bounds reports in the IPv6
FIB code while running syzkaller fuzzer. The root cause is a dead dst
that is on the garbage list gets reinserted into the IPv6 FIB. While on
the gc (or perhaps when it gets added to the gc list) the dst->next is
set to an IPv4 dst. A subsequent walk of the ipv6 tables causes the
out-of-bounds access.
Andrey's reproducer was the key to getting to the bottom of this.
With IPv6, host routes for an address have the dst->dev set to the
loopback device. When the 'lo' device is taken down, rt6_ifdown initiates
a walk of the fib evicting routes with the 'lo' device which means all
host routes are removed. That process moves the dst which is attached to
an inet6_ifaddr to the gc list and marks it as dead.
The recent change to keep global IPv6 addresses added a new function,
fixup_permanent_addr, that is called on admin up. That function restarts
dad for an inet6_ifaddr and when it completes the host route attached
to it is inserted into the fib. Since the route was marked dead and
moved to the gc list, re-inserting the route causes the reported
out-of-bounds accesses. If the device with the address is taken down
or the address is removed, the WARN_ON in fib6_del is triggered.
All of those faults are fixed by regenerating the host route if the
existing one has been moved to the gc list, something that can be
determined by checking if the rt6i_ref counter is 0.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 557c44be91 ]
Andrey reported a fault in the IPv6 route code:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 1 PID: 4035 Comm: a.out Not tainted 4.11.0-rc7+ #250
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff880069809600 task.stack: ffff880062dc8000
RIP: 0010:ip6_rt_cache_alloc+0xa6/0x560 net/ipv6/route.c:975
RSP: 0018:ffff880062dced30 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: ffff8800670561c0 RCX: 0000000000000006
RDX: 0000000000000003 RSI: ffff880062dcfb28 RDI: 0000000000000018
RBP: ffff880062dced68 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff880062dcfb28 R14: dffffc0000000000 R15: 0000000000000000
FS: 00007feebe37e7c0(0000) GS:ffff88006cb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000205a0fe4 CR3: 000000006b5c9000 CR4: 00000000000006e0
Call Trace:
ip6_pol_route+0x1512/0x1f20 net/ipv6/route.c:1128
ip6_pol_route_output+0x4c/0x60 net/ipv6/route.c:1212
...
Andrey's syzkaller program passes rtmsg.rtmsg_flags with the RTF_PCPU bit
set. Flags passed to the kernel are blindly copied to the allocated
rt6_info by ip6_route_info_create making a newly inserted route appear
as though it is a per-cpu route. ip6_rt_cache_alloc sees the flag set
and expects rt->dst.from to be set - which it is not since it is not
really a per-cpu copy. The subsequent call to __ip6_dst_alloc then
generates the fault.
Fix by checking for the flag and failing with EINVAL.
Fixes: d52d3997f8 ("ipv6: Create percpu rt6_info")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1862d6208d ]
Syzkaller reported a use-after-free in ip_recv_error at line
info->ipi_ifindex = skb->dev->ifindex;
This function is called on dequeue from the error queue, at which
point the device pointer may no longer be valid.
Save ifindex on enqueue in __skb_complete_tx_timestamp, when the
pointer is valid or NULL. Store it in temporary storage skb->cb.
It is safe to reference skb->dev here, as called from device drivers
or dev_queue_xmit. The exception is when called from tcp_ack_tstamp;
in that case it is NULL and ifindex is set to 0 (invalid).
Do not return a pktinfo cmsg if ifindex is 0. This maintains the
current behavior of not returning a cmsg if skb->dev was NULL.
On dequeue, the ipv4 path will cast from sock_exterr_skb to
in_pktinfo. Both have ifindex as their first element, so no explicit
conversion is needed. This is by design, introduced in commit
0b922b7a82 ("net: original ingress device index in PKTINFO"). For
ipv6 ip6_datagram_support_cmsg converts to in6_pktinfo.
Fixes: 829ae9d611 ("net-timestamp: allow reading recv cmsg on errqueue with origin tstamp")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a2d6cbb067 ]
addrconf_ifdown() removes elements from the idev->addr_list without
holding the idev->lock.
If this happens while the loop in __ipv6_dev_get_saddr() is handling the
same element, that function ends up in an infinite loop:
NMI watchdog: BUG: soft lockup - CPU#1 stuck for 23s! [test:1719]
Call Trace:
ipv6_get_saddr_eval+0x13c/0x3a0
__ipv6_dev_get_saddr+0xe4/0x1f0
ipv6_dev_get_saddr+0x1b4/0x204
ip6_dst_lookup_tail+0xcc/0x27c
ip6_dst_lookup_flow+0x38/0x80
udpv6_sendmsg+0x708/0xba8
sock_sendmsg+0x18/0x30
SyS_sendto+0xb8/0xf8
syscall_common+0x34/0x58
Fixes: 6a923934c3 (Revert "ipv6: Revert optional address flusing on ifdown.")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2ed1880fd upstream.
The protocol field is checked when deleting IPv4 routes, but ignored for
IPv6, which causes problems with routing daemons accidentally deleting
externally set routes (observed by multiple bird6 users).
This can be verified using `ip -6 route del <prefix> proto something`.
Signed-off-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d515684d78 ]
In the case udp_sk(sk)->pending is AF_INET6, udpv6_sendmsg() would
jump to do_append_data, skipping the initialization of sockc.tsflags.
Fix the problem by moving sockc.tsflags initialization earlier.
The bug was detected with KMSAN.
Fixes: c14ac9451c ("sock: enable timestamping using control messages")
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45caeaa5ac ]
As Eric Dumazet pointed out this also needs to be fixed in IPv6.
v2: Contains the IPv6 tcp/Ipv6 dccp patches as well.
We have seen a few incidents lately where a dst_enty has been freed
with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that
dst_entry. If the conditions/timings are right a crash then ensues when the
freed dst_entry is referenced later on. A Common crashing back trace is:
#8 [] page_fault at ffffffff8163e648
[exception RIP: __tcp_ack_snd_check+74]
.
.
#9 [] tcp_rcv_established at ffffffff81580b64
#10 [] tcp_v4_do_rcv at ffffffff8158b54a
#11 [] tcp_v4_rcv at ffffffff8158cd02
#12 [] ip_local_deliver_finish at ffffffff815668f4
#13 [] ip_local_deliver at ffffffff81566bd9
#14 [] ip_rcv_finish at ffffffff8156656d
#15 [] ip_rcv at ffffffff81566f06
#16 [] __netif_receive_skb_core at ffffffff8152b3a2
#17 [] __netif_receive_skb at ffffffff8152b608
#18 [] netif_receive_skb at ffffffff8152b690
#19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3]
#20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3]
#21 [] net_rx_action at ffffffff8152bac2
#22 [] __do_softirq at ffffffff81084b4f
#23 [] call_softirq at ffffffff8164845c
#24 [] do_softirq at ffffffff81016fc5
#25 [] irq_exit at ffffffff81084ee5
#26 [] do_IRQ at ffffffff81648ff8
Of course it may happen with other NIC drivers as well.
It's found the freed dst_entry here:
224 static bool tcp_in_quickack_mode(struct sock *sk)↩
225 {↩
226 ▹ const struct inet_connection_sock *icsk = inet_csk(sk);↩
227 ▹ const struct dst_entry *dst = __sk_dst_get(sk);↩
228 ↩
229 ▹ return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩
230 ▹ ▹ (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩
231 }↩
But there are other backtraces attributed to the same freed dst_entry in
netfilter code as well.
All the vmcores showed 2 significant clues:
- Remote hosts behind the default gateway had always been redirected to a
different gateway. A rtable/dst_entry will be added for that host. Making
more dst_entrys with lower reference counts. Making this more probable.
- All vmcores showed a postitive LockDroppedIcmps value, e.g:
LockDroppedIcmps 267
A closer look at the tcp_v4_err() handler revealed that do_redirect() will run
regardless of whether user space has the socket locked. This can result in a
race condition where the same dst_entry cached in sk->sk_dst_entry can be
decremented twice for the same socket via:
do_redirect()->__sk_dst_check()-> dst_release().
Which leads to the dst_entry being prematurely freed with another socket
pointing to it via sk->sk_dst_cache and a subsequent crash.
To fix this skip do_redirect() if usespace has the socket locked. Instead let
the redirect take place later when user space does not have the socket
locked.
The dccp/IPv6 code is very similar in this respect, so fixing it there too.
As Eric Garver pointed out the following commit now invalidates routes. Which
can set the dst->obsolete flag so that ipv4_dst_check() returns null and
triggers the dst_release().
Fixes: ceb3320610 ("ipv4: Kill routes during PMTU/redirect updates.")
Cc: Eric Garver <egarver@redhat.com>
Cc: Hannes Sowa <hsowa@redhat.com>
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 79e49503ef ]
ip6_fragment, in case skb has a fraglist, checks if the
skb is cloned. If it is, it will move to the 'slow path' and allocates
new skbs for each fragment.
However, right before entering the slowpath loop, it updates the
nexthdr value of the last ipv6 extension header to NEXTHDR_FRAGMENT,
to account for the fragment header that will be inserted in the new
ipv6-fragment skbs.
In case original skb is cloned this munges nexthdr value of another
skb. Avoid this by doing the nexthdr update for each of the new fragment
skbs separately.
This was observed with tcpdump on a bridge device where netfilter ipv6
reassembly is active: tcpdump shows malformed fragment headers as
the l4 header (icmpv6, tcp, etc). is decoded as a fragment header.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Andreas Karis <akaris@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 67e194007b ]
Commit 2759647247 ("ipv6: fix ECMP route replacement") introduced a
loop that removes all siblings of an ECMP route that is being
replaced. However, this loop doesn't stop when it has replaced
siblings, and keeps removing other routes with a higher metric.
We also end up triggering the WARN_ON after the loop, because after
this nsiblings < 0.
Instead, stop the loop when we have taken care of all routes with the
same metric as the route being replaced.
Reproducer:
===========
#!/bin/sh
ip netns add ns1
ip netns add ns2
ip -net ns1 link set lo up
for x in 0 1 2 ; do
ip link add veth$x netns ns2 type veth peer name eth$x netns ns1
ip -net ns1 link set eth$x up
ip -net ns2 link set veth$x up
done
ip -net ns1 -6 r a 2000::/64 nexthop via fe80::0 dev eth0 \
nexthop via fe80::1 dev eth1 nexthop via fe80::2 dev eth2
ip -net ns1 -6 r a 2000::/64 via fe80::42 dev eth0 metric 256
ip -net ns1 -6 r a 2000::/64 via fe80::43 dev eth0 metric 2048
echo "before replace, 3 routes"
ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
echo
ip -net ns1 -6 r c 2000::/64 nexthop via fe80::4 dev eth0 \
nexthop via fe80::5 dev eth1 nexthop via fe80::6 dev eth2
echo "after replace, only 2 routes, metric 2048 is gone"
ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 294acf1c01 ]
The gso code of several tunnels type (gre and udp tunnels)
takes for granted that the skb->inner_protocol is properly
initialized and drops the packet elsewhere.
On the forwarding path no one is initializing such field,
so gro encapsulated packets are dropped on forward.
Since commit 3872035241 ("gre: Use inner_proto to obtain
inner header protocol"), this can be reproduced when the
encapsulated packets use gre as the tunneling protocol.
The issue happens also with vxlan and geneve tunnels since
commit 8bce6d7d0d ("udp: Generalize skb_udp_segment"), if the
forwarding host's ingress nic has h/w offload for such tunnel
and a vxlan/geneve device is configured on top of it, regardless
of the configured peer address and vni.
To address the issue, this change initialize the inner_protocol
field for encapsulated packets in both ipv4 and ipv6 gro complete
callbacks.
Fixes: 3872035241 ("gre: Use inner_proto to obtain inner header protocol")
Fixes: 8bce6d7d0d ("udp: Generalize skb_udp_segment")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7dcdf941cd ]
Align vti6 with vti by returning GRE_KEY flag. This enables iproute2
to display tunnel keys on "ip -6 tunnel show"
Signed-off-by: David Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92e55f412c upstream.
Unlike ipv4, this control socket is shared by all cpus so we cannot use
it as scratchpad area to annotate the mark that we pass to ip6_xmit().
Add a new parameter to ip6_xmit() to indicate the mark. The SCTP socket
family caches the flowi6 structure in the sctp_transport structure, so
we cannot use to carry the mark unless we later on reset it back, which
I discarded since it looks ugly to me.
Fixes: bf99b4ded5 ("tcp: fix mark propagation with fwmark_reflect enabled")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf99b4ded5 upstream.
Otherwise, RST packets generated by the TCP stack for non-existing
sockets always have mark 0.
The mark from the original packet is assigned to the netns_ipv4/6
socket used to send the response so that it can get copied into the
response skb when the socket sends it.
Fixes: e110861f86 ("net: add a sysctl to reflect the fwmark on replies")
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Pau Espin Pedrol <pau.espin@tessares.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9c8bb163ae ]
In function igmpv3/mld_add_delrec() we allocate pmc and put it in
idev->mc_tomb, so we should free it when we don't need it in del_delrec().
But I removed kfree(pmc) incorrectly in latest two patches. Now fix it.
Fixes: 24803f38a5 ("igmp: do not remove igmp souce list info when ...")
Fixes: 1666d49e1d ("mld: do not remove mld souce list info when ...")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1666d49e1d ]
This is an IPv6 version of commit 24803f38a5 ("igmp: do not remove igmp
souce list..."). In mld_del_delrec(), we will restore back all source filter
info instead of flush them.
Move mld_clear_delrec() from ipv6_mc_down() to ipv6_mc_destroy_dev() since
we should not remove source list info when set link down. Remove
igmp6_group_dropped() in ipv6_mc_destroy_dev() since we have called it in
ipv6_mc_down().
Also clear all source info after igmp6_group_dropped() instead of in it
because ipv6_mc_down() will call igmp6_group_dropped().
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ebf6c9cb23 ]
Dmitry reported use-after-free in ip6_datagram_recv_specific_ctl()
A similar bug was fixed in commit 8ce48623f0 ("ipv6: tcp: restore
IP6CB for pktoptions skbs"), but I missed another spot.
tcp_v6_syn_recv_sock() can indeed set np->pktoptions from ireq->pktopts
Fixes: 971f10eca1 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7892032cfe ]
Andrey Konovalov reported out of bound accesses in ip6gre_err()
If GRE flags contains GRE_KEY, the following expression
*(((__be32 *)p) + (grehlen / 4) - 1)
accesses data ~40 bytes after the expected point, since
grehlen includes the size of IPv6 headers.
Let's use a "struct gre_base_hdr *greh" pointer to make this
code more readable.
p[1] becomes greh->protocol.
grhlen is the GRE header length.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63117f09c7 ]
Casting is a high precedence operation but "off" and "i" are in terms of
bytes so we need to have some parenthesis here.
Fixes: fbfa743a9d ("ipv6: fix ip6_tnl_parse_tlv_enc_lim()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fbfa743a9d ]
This function suffers from multiple issues.
First one is that pskb_may_pull() may reallocate skb->head,
so the 'raw' pointer needs either to be reloaded or not used at all.
Second issue is that NEXTHDR_DEST handling does not validate
that the options are present in skb->data, so we might read
garbage or access non existent memory.
With help from Willem de Bruijn.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
