[ Upstream commit 71eae1ca77 ]
The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25
(bits 0-15 usually used for that are occupied by the packet checksum).
Thus we need to set the 'shift_rd0' field in the SH7734 SoC data...
Fixes: f0e81fecd4 ("net: sh_eth: Add support SH7734")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63dfb0dac9 ]
The USB core may call reset_resume when it fails to resume asix device.
And USB core can recovery this abnormal resume at low level driver,
the same .resume at asix driver can work too. Add .reset_resume can
avoid disconnecting after backing from system resume, and NFS can
still be mounted after this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 096de2f83e ]
When VXLAN offloading is enabled, be_features_check() tries to check if
an encapsulated packet is indeed a VXLAN packet. The check is not strict
enough, and considers any UDP-encapsulated ethernet frame with a 8-byte
tunnel header as being VXLAN. Unfortunately, both GENEVE and VXLAN-GPE
have a 8-byte header, so they get through this check.
Force the UDP destination port to be the one that has been offloaded to
hardware.
Without this, GENEVE-encapsulated packets can end up having an incorrect
checksum when both a GENEVE and a VXLAN (offloaded) tunnel are
configured.
This is similar to commit a547224dce ("mlx4e: Do not attempt to
offload VXLAN ports that are unrecognized").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10b1c04e92 ]
Demoting simple flow steering rule priority (for DPDK) was achieved by
wrapping FW commands MLX4_QP_FLOW_STEERING_ATTACH/DETACH for the PF
as well, and forcing the priority to MLX4_DOMAIN_NIC in the wrapper
function for the PF and all VFs.
In function mlx4_ib_create_flow(), this change caused the main rule
creation for the PF to be wrapped, while it left the associated
tunnel steering rule creation unwrapped for the PF.
This mismatch caused rule deletion failures in mlx4_ib_destroy_flow()
for the PF when the detach wrapper function did not find the associated
tunnel-steering rule (since creation of that rule for the PF did not
go through the wrapper function).
Fix this by setting MLX4_QP_FLOW_STEERING_ATTACH/DETACH to be "native"
(so that the PF invocation does not go through the wrapper), and perform
the required priority demotion for the PF in the mlx4_ib_create_flow()
code path.
Fixes: 48564135cb ("net/mlx4_core: Demote simple multicast and broadcast flow steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c1d5f8ff80 ]
This patch removes BUG_ON() macro from mlx4_alloc_icm_coherent()
by checking DMA address alignment in advance and performing proper
folding in case of error.
Fixes: 5b0bf5e25e ("mlx4_core: Support ICM tables in coherent memory")
Reported-by: Ozgur Karatas <okaratas@member.fsf.org>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b01fe7f91 ]
mlx4_QP_FLOW_STEERING_DETACH_wrapper first removes the steering
rule (which results in freeing the rule structure), and then
references a field in this struct (the qp number) when releasing the
busy-status on the rule's qp.
Since this memory was freed, it could reallocated and changed.
Therefore, the qp number in the struct may be incorrect,
so that we are releasing the incorrect qp. This leaves the rule's qp
in the busy state (and could possibly release an incorrect qp as well).
Fix this by saving the qp number in a local variable, for use after
removing the steering rule.
Fixes: 2c473ae7e5 ("net/mlx4_core: Disallow releasing VF QPs which have steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9da34cd34e ]
Under the switchdev/offloads mode, packets that don't match any
e-switch steering rule are sent towards the e-switch management
port. We use a NIC HW steering rule set per vport (uplink and VFs)
to make them be received into the host OS through the respective
vport representor netdevice.
Currnetly such missed RoCE packets will not get to this NIC steering
rule, and hence VF RoCE will not work over the slow path of the offloads
mode. This is b/c these packets will be matched by a steering rule added
by the firmware that serves RoCE traffic set on the PF NIC vport which
is also the e-switch management port under SRIOV.
Disabling RoCE on the e-switch management vport when we are in the offloads
mode, will signal to the firmware to remove their RoCE rule, and then the
missed RoCE packets will be matched by the representor NIC steering rule
as any other missed packets.
To achieve that, we disable RoCE on the PF vport. We do that by removing
(hot-unplugging) the IB device instance associated with the PF. This is
also required by our current model where the PF serves as the uplink
representor and hence only SW switching (TC, bridge, OVS) applications
and slow path vport mlx5e net-device should be running over that vport.
Fixes: c930a3ad74 ('net/mlx5e: Add devlink based SRIOV mode changes')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 610c908773 ]
This chip is the same as RTL8168, but its device id is 0x8161.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfb5b098e0 upstream.
When FW crashes with no_fw_recovery option, driver
waits for manual recovery with wil->mutex held, this
can easily create deadlocks.
Fix the problem by moving the wait outside the lock.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0878fff1f4 upstream.
The Generic PHY driver is a catch-all PHY driver and it should preserve
whatever prior initialization has been done by boot loader or firmware
agents. For specific PHY device configuration it is expected that a
specialized PHY driver would take over that role.
Resetting the generic PHY was a bad idea that has lead to several
complaints and downstream workarounds e.g: in OpenWrt/LEDE so restore
the behavior prior to 87aa9f9c61 ("net: phy: consolidate PHY
reset in phy_init_hw()").
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 440aeca4b9 upstream.
The functions igb_read_phy_reg_gs40g/igb_write_phy_reg_gs40g (which were
removed in 2a3cdea) explicitly selected the required page at every phy_reg
access. Currently, igb_get_phy_id_82575 relays on the fact that page 0 is
already selected. The assumption is not fulfilled for my Lex 3I380CW
motherboard with integrated dual i211 based gigabit ethernet. This leads to igb
initialization failure and network interfaces are not working:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of 0000:01:00.0 failed with error -2
igb: probe of 0000:02:00.0 failed with error -2
In order to fix it, we explicitly select page 0 before first access to phy
registers.
See also: https://bugzilla.suse.com/show_bug.cgi?id=1009911
See also: http://www.lex.com.tw/products/pdf/3I380A&3I380CW.pdf
Fixes: 2a3cdea ("igb: Remove GS40G specific defines/functions")
Signed-off-by: Matwey V Kornilov <matwey@sai.msu.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a4274bf2d upstream.
In the stable linux-3.16 branch, I ran into a warning in the
wlcore driver:
drivers/net/wireless/ti/wlcore/spi.c: In function 'wl12xx_spi_raw_write':
drivers/net/wireless/ti/wlcore/spi.c:315:1: error: the frame size of 12848 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
Newer kernels no longer show the warning, but the bug is still there,
as the allocation is based on the CPU page size rather than the
actual capabilities of the hardware.
This replaces the PAGE_SIZE macro with the SZ_4K macro, i.e. 4096 bytes
per buffer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bde717ab47 upstream.
The hard coded register 0x9864 and 0x9924 are invalid
for ar9300 chips.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf8ce1ea61 upstream.
One scenario that could lead to UAF is two threads writing
simultaneously to the "tx99" debug file. One of them would
set the "start" value to true and follow to ath9k_tx99_init().
Inside the function it would set the sc->tx99_state to true
after allocating sc->tx99skb. Then, the other thread would
execute write_file_tx99() and call ath9k_tx99_deinit().
sc->tx99_state would be freed. After that, the first thread
would continue inside ath9k_tx99_init() and call
r = ath9k_tx99_send(sc, sc->tx99_skb, &txctl);
that would make use of the freed sc->tx99_skb memory.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c70d68150f ]
If we have more than 32 unicast MAC addresses assigned to an interface
we will read beyond the end of the address table in the driver when
adding filters. The next 256 entries store multicast addresses, so we
will end up attempting to insert duplicate filters, which is mostly
harmless. If we add more than 288 unicast addresses we will then read
past the multicast address table, which is likely to be more exciting.
Fixes: 12fb0da45c ("sfc: clean fallbacks between promisc/normal in efx_ef10_filter_sync_rx_mode")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ea59db8a3 upstream.
An earlier change to this function (3bdae81072) fixed a leak in the
case of an unsuccessful call to brcmf_sdiod_buffrw(). However, the
glom_skb buffer, used for emulating a scattering read, is never used
or referenced after its contents are copied into the destination
buffers, and therefore always needs to be freed by the end of the
function.
Fixes: 3bdae81072 ("brcmfmac: Fix glob_skb leak in brcmf_sdiod_recv_chain")
Fixes: a413e39a38 ("brcmfmac: fix brcmf_sdcard_recv_chain() for host without sg support")
Signed-off-by: Peter S. Housel <housel@acm.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57c00f2fac upstream.
If 'wiphy_new()' fails, we leak 'ops'. Add a new label in the error
handling path to free it in such a case.
Fixes: 5c22fb8510 ("brcmfmac: add wowl gtk rekeying offload support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f44c9a413 upstream.
The lower level nl80211 code in cfg80211 ensures that "len" is between
25 and NL80211_ATTR_FRAME (2304). We subtract DOT11_MGMT_HDR_LEN (24) from
"len" so thats's max of 2280. However, the action_frame->data[] buffer is
only BRCMF_FIL_ACTION_FRAME_SIZE (1800) bytes long so this memcpy() can
overflow.
memcpy(action_frame->data, &buf[DOT11_MGMT_HDR_LEN],
le16_to_cpu(action_frame->len));
Fixes: 18e2f61db3 ("brcmfmac: P2P action frame tx.")
Reported-by: "freenerguo(郭大兴)" <freenerguo@tencent.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 69e766612c ]
It's not a good idea to add the same hlist_node to two different hash lists.
This leads to various hard to debug memory corruptions.
Fixes: b1be00a6c3 ("vxlan: support both IPv4 and IPv6 sockets in a single vxlan device")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ff93de766 upstream.
Symbol error during carrier counter from PPCNT was mistakenly reported as
TX carrier errors in get_stats ndo, although it's an RX counter.
Fixes: 269e6b3af3 ("net/mlx5e: Report additional error statistics in get stats ndo")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05a6b4cae8 upstream.
The code that detects a failed soft reset of Octeon is comparing the wrong
value against the reset value of the Octeon SLI_SCRATCH_1 register,
resulting in an inability to detect a soft reset failure. Fix it by using
the correct value in the comparison, which is any non-zero value.
Fixes: f21fb3ed36 ("Add support of Cavium Liquidio ethernet adapters")
Fixes: c0eab5b358 ("liquidio: CN23XX firmware download")
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a0165a034 upstream.
Draining the health workqueue will ignore future health works including
the one that report hardware failure and thus we can't enter error state
Instead cancel the recovery flow and make sure only recovery flow won't
be scheduled.
Fixes: 5e44fca504 ('net/mlx5: Only cancel recovery work when cleaning up device')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acb4b7df48 upstream.
My static checker complains that ofdpa_neigh_del() can sometimes free
"found". It just makes sense to use it first before deleting it.
Fixes: ecf244f753 ("rocker: fix maybe-uninitialized warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db9d8b29d1 upstream.
The function, skb_complete_tx_timestamp(), used to allow passing in a
NULL pointer for the time stamps, but that was changed in commit
62bccb8cdb ("net-timestamp: Make the
clone operation stand-alone from phy timestamping"), and the existing
call sites, all of which are in the dp83640 driver, were fixed up.
Even though the kernel-doc was subsequently updated in commit
7a76a021cd ("net-timestamp: Update
skb_complete_tx_timestamp comment"), still a bug fix from Manfred
Rudigier came into the driver using the old semantics. Probably
Manfred derived that patch from an older kernel version.
This fix should be applied to the stable trees as well.
Fixes: 81e8f2e930 ("net: dp83640: Fix tx timestamp overflow handling.")
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b866203d87 upstream.
The commit ("net/phy: micrel: Add workaround for bad autoneg") fixes an
autoneg failure case by resetting the hardware. This turns off
intterupts. Things will work themselves out if the phy polls, as it will
figure out it's state during a poll. However if the phy uses only
intterupts, the phy will stall, since interrupts are off. This patch
fixes the issue by calling config_intr after resetting the phy.
Fixes: d2fd719bcb ("net/phy: micrel: Add workaround for bad autoneg ")
Signed-off-by: Zach Brown <zach.brown@ni.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 538d92912d upstream.
The commit 90c311b0ee ("xen-netfront: Fix Rx stall during network
stress and OOM") caused the refill timer to be triggerred almost on
all invocations of xennet_alloc_rx_buffers for certain workloads.
This reworks the fix by reverting to the old behaviour and taking into
consideration the skb allocation failure. Refill timer is now triggered
on insufficient requests or skb allocation failure.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Fixes: 90c311b0ee (xen-netfront: Fix Rx stall during network stress and OOM)
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b08b5b53a1 upstream.
Similarly to QCA6174, QCA9377 requires the CE5 configuration to be
available for other feature. Use the ath10k_pci_override_ce_config()
for it as well.
This is required for TF2.0 firmware. Previous FW revisions were
working fine without this patch.
Fixes: a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fbcfeb8a9 upstream.
mac80211_hwsim initializes a hrtimer with clockid
CLOCK_MONOTONIC_RAW. That's not supported.
Use CLOCK_MONOTONIC instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77c0d0cd10 upstream.
Our code was assigning number of channels to the index variable by
default. If firmware reported channel we didn't predict this would
result in using that initial index value and writing out of array. This
never happened so far (we got a complete list of supported channels) but
it means possible memory corruption so we should handle it anyway.
This patch simply detects unexpected channel and ignores it.
As we don't try to create new entry now, it's also safe to drop hw_value
and center_freq assignment. For known channels we have these set anyway.
I decided to fix this issue by assigning NULL or a target channel to the
channel variable. This was one of possible ways, I prefefred this one as
it also avoids using channel[index] over and over.
Fixes: 58de92d2f9 ("brcmfmac: use static superset of channels for wiphy bands")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9577b174cd ]
When running SRIOV, warnings for SRQ LIMIT events flood the Hypervisor's
message log when (correct, normally operating) apps use SRQ LIMIT events
as a trigger to post WQEs to SRQs.
Add more information to the existing debug printout for SRQ_LIMIT, and
output the warning messages only for the SRQ CATAS ERROR event.
Fixes: acba2420f9 ("mlx4_core: Add wrapper functions and comm channel and slave event support to EQs")
Fixes: e0debf9cb5 ("mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 34c55cf2fc ]
Currently dp83867 driver returns error if phy interface type
PHY_INTERFACE_MODE_RGMII_RXID is used to set the rx only internal
delay. Similarly issue happens for PHY_INTERFACE_MODE_RGMII_TXID.
Fix this by checking also the interface type if a particular delay
value is missing in the phy dt bindings. Also update the DT document
accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3439352916 ]
During interface opening MAC address stored in netdev->dev_addr is
programmed in the HW with exception of BE3 VFs where the initial
MAC is programmed by parent PF. This is OK when MAC address is not
changed when an interfaces is down. In this case the requested MAC is
stored to netdev->dev_addr and later is stored into HW during opening.
But this is not done for all BE3 VFs so the NIC HW does not know
anything about this change and all traffic is filtered.
This is the case of bonding if fail_over_mac == 0 where the MACs of
the slaves are changed while they are down.
The be2net behavior is too restrictive because if a BE3 VF has
the FILTMGMT privilege then it is able to modify its MAC without
any restriction.
To solve the described problem the driver should take care about these
privileged BE3 VFs so the MAC is programmed during opening. And by
contrast unpriviled BE3 VFs should not be allowed to change its MAC
in any case.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d928ae590 ]
BE3 VFs without FILTMGMT privilege are not allowed to modify its MAC,
VLAN table and UC/MC lists. So don't try to delete MAC on such VFs.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe68d8bfe5 ]
Return value from be_mcc_notify_wait() contains a base completion status
together with an additional status. The base_status() macro need to be
used to access base status.
Fixes: e3a7ae2 be2net: Changing MAC Address of a VF was broken
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7aa4865506 ]
While probing BGX we requesting appropriate QLM for it's configuration
and get LMAC count by that request. Then, while reading configured
MAC values from SSDT table we need to save them in proper mapping:
BGX[i]->lmac[j].mac = <MAC value>
to later provide for initialization stuff. In order to fill
such mapping properly we need to add lmac index to be used while
acpi initialization since at this moment bgx->lmac_count already contains
actual value.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a13c06525a ]
When an Marvell 88E1512 PHY is connected to a nic in SGMII mode, the
fiber page is used for the SGMII host-side connection. The PHY driver
notices that SUPPORTED_FIBRE is set, so it tries reading the fiber page
for the link status, and ends up reading the MAC-side status instead of
the outgoing (copper) link. This leads to incorrect results reported
via ethtool.
If the PHY is connected via SGMII to the host, ignore the fiber page.
However, continue to allow the existing power management code to
suspend and resume the fiber page.
Fixes: 6cfb3bcc06 ("Marvell phy: check link status in case of fiber link.")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 23d28a859f ]
When using the ibmveth driver in a KVM/QEMU based VM, it currently
always prints out a scary error message like this when it is started:
ibmveth 71000003 (unregistered net_device): unable to change
checksum offload settings. 1 rc=-2 ret_attr=71000003
This happens because the driver always tries to enable the checksum
offloading without checking for the availability of this feature first.
QEMU does not support checksum offloading for the spapr-vlan device,
thus we always get the error message here.
According to the LoPAPR specification, the "ibm,illan-options" property
of the corresponding device tree node should be checked first to see
whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading
feature is available. Thus let's do this in the ibmveth driver, too, so
that the error message is really only limited to cases where something
goes wrong, and does not occur if the feature is just missing.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit efb5f68f32 ]
Mac aging is applicable only for dynamically learnt remote mac
entries. Check for user configured static remote mac entries
and skip aging.
Signed-off-by: Balakrishnan Raman <ramanb@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0fa28f000 ]
I don't have any guests with PAGE_SIZE > 64k but the
code seems to be clearly broken in that case
as PAGE_SIZE / MERGEABLE_BUFFER_ALIGN will need
more than 8 bit and so the code in mergeable_ctx_to_buf_address
does not give us the actual true size.
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a59b7e0246 ]
mlxsw_sp_nexthop_group_mac_update() is called in one of two cases:
1) When the MAC of a nexthop needs to be updated
2) When the size of a nexthop group has changed
In the second case the adjacency entries for the nexthop group need to
be reallocated from the adjacency table. In this case we must write to
the entries the MAC addresses of all the nexthops that should be
offloaded and not only those whose MAC changed. Otherwise, these entries
would be filled with garbage data, resulting in packet loss.
Fixes: a7ff87acd9 ("mlxsw: spectrum_router: Implement next-hop routing")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 738f7f6473 ]
The xgbe_init() routine returns a return code indicating success or
failure, but the return code is not checked. Add code to xgbe_init()
to issue a message when failures are seen and add code to check the
xgbe_init() return code.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92549cdc28 ]
A recent firmware change seems to have enabled thermal zones on the
iwlwifi driver. Unfortunately, my device fails when registering the
thermal zone. This doesn't stop the driver from attempting to unregister
the thermal zone at unload time, triggering a NULL pointer deference in
strlen() off the thermal_zone_device_unregister() path.
Don't unregister if name is NULL, for that case we failed registering.
Do the same for the cooling zone.
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90c311b0ee ]
During an OOM scenario, request slots could not be created as skb
allocation fails. So the netback cannot pass in packets and netfront
wrongly assumes that there is no more work to be done and it disables
polling. This causes Rx to stall.
The issue is with the retry logic which schedules the timer if the
created slots are less than NET_RX_SLOTS_MIN. The count of new request
slots to be pushed are calculated as a difference between new req_prod
and rsp_cons which could be more than the actual slots, if there are
unconsumed responses.
The fix is to calculate the count of newly created slots as the
difference between new req_prod and old req_prod.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 69fed99baa ]
A driver using dev_alloc_page() must not reuse a page that had to
use emergency memory reserve.
Otherwise all packets using this page will be immediately dropped,
unless for very specific sockets having SOCK_MEMALLOC bit set.
This issue might be hard to debug, because only a fraction of the RX
ring buffer would suffer from drops.
Fixes: 75354148ce ("gianfar: Add paged allocation and Rx S/G")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 719ca81114 ]
In the TPA GRO code path, initialize the tcp_opt_len variable to 0 so
that it will be correct for packets without TCP timestamps. The bug
caused the SKB fields to be incorrectly set up for packets without
TCP timestamps, leading to these packets being rejected by the stack.
Reported-by: Andy Gospodarek <andrew.gospodarek@broadocm.com>
Acked-by: Andy Gospodarek <andrew.gospodarek@broadocm.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f16f1df65f ]
vif->lock is used to protect statistics gathering agents from using the
queue structure during cleaning.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
