[ Upstream commit 5d621672bc ]
The wrong register is checked for the Tx flow control bit,
it should have been maccfg1 not maccfg2.
This went unnoticed for so long probably because the impact is
hardly visible, not to mention the tangled code from adjust_link().
First, link flow control (i.e. handling of Rx/Tx link level pause frames)
is disabled by default (needs to be enabled via 'ethtool -A').
Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few
old boards), which results in Tx flow control remaining always on
once activated.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 25cc72a338 ]
The mlxsw driver relies on NETDEV_CHANGEUPPER events to configure the
device in case a port is enslaved to a master netdev such as bridge or
bond.
Since the driver ignores events unrelated to its ports and their
uppers, it's possible to engineer situations in which the device's data
path differs from the kernel's.
One example to such a situation is when a port is enslaved to a bond
that is already enslaved to a bridge. When the bond was enslaved the
driver ignored the event - as the bond wasn't one of its uppers - and
therefore a bridge port instance isn't created in the device.
Until such configurations are supported forbid them by checking that the
upper device doesn't have uppers of its own.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Nogah Frankel <nogahf@mellanox.com>
Tested-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ebc8254aea ]
This reverts commit 7ad813f208 ("net: phy:
Correctly process PHY_HALTED in phy_stop_machine()") because it is
creating the possibility for a NULL pointer dereference.
David Daney provide the following call trace and diagram of events:
When ndo_stop() is called we call:
phy_disconnect()
+---> phy_stop_interrupts() implies: phydev->irq = PHY_POLL;
+---> phy_stop_machine()
| +---> phy_state_machine()
| +----> queue_delayed_work(): Work queued.
+--->phy_detach() implies: phydev->attached_dev = NULL;
Now at a later time the queued work does:
phy_state_machine()
+---->netif_carrier_off(phydev->attached_dev): Oh no! It is NULL:
CPU 12 Unable to handle kernel paging request at virtual address
0000000000000048, epc == ffffffff80de37ec, ra == ffffffff80c7c
Oops[#1]:
CPU: 12 PID: 1502 Comm: kworker/12:1 Not tainted 4.9.43-Cavium-Octeon+ #1
Workqueue: events_power_efficient phy_state_machine
task: 80000004021ed100 task.stack: 8000000409d70000
$ 0 : 0000000000000000 ffffffff84720060 0000000000000048 0000000000000004
$ 4 : 0000000000000000 0000000000000001 0000000000000004 0000000000000000
$ 8 : 0000000000000000 0000000000000000 00000000ffff98f3 0000000000000000
$12 : 8000000409d73fe0 0000000000009c00 ffffffff846547c8 000000000000af3b
$16 : 80000004096bab68 80000004096babd0 0000000000000000 80000004096ba800
$20 : 0000000000000000 0000000000000000 ffffffff81090000 0000000000000008
$24 : 0000000000000061 ffffffff808637b0
$28 : 8000000409d70000 8000000409d73cf0 80000000271bd300 ffffffff80c7804c
Hi : 000000000000002a
Lo : 000000000000003f
epc : ffffffff80de37ec netif_carrier_off+0xc/0x58
ra : ffffffff80c7804c phy_state_machine+0x48c/0x4f8
Status: 14009ce3 KX SX UX KERNEL EXL IE
Cause : 00800008 (ExcCode 02)
BadVA : 0000000000000048
PrId : 000d9501 (Cavium Octeon III)
Modules linked in:
Process kworker/12:1 (pid: 1502, threadinfo=8000000409d70000,
task=80000004021ed100, tls=0000000000000000)
Stack : 8000000409a54000 80000004096bab68 80000000271bd300 80000000271c1e00
0000000000000000 ffffffff808a1708 8000000409a54000 80000000271bd300
80000000271bd320 8000000409a54030 ffffffff80ff0f00 0000000000000001
ffffffff81090000 ffffffff808a1ac0 8000000402182080 ffffffff84650000
8000000402182080 ffffffff84650000 ffffffff80ff0000 8000000409a54000
ffffffff808a1970 0000000000000000 80000004099e8000 8000000402099240
0000000000000000 ffffffff808a8598 0000000000000000 8000000408eeeb00
8000000409a54000 00000000810a1d00 0000000000000000 8000000409d73de8
8000000409d73de8 0000000000000088 000000000c009c00 8000000409d73e08
8000000409d73e08 8000000402182080 ffffffff808a84d0 8000000402182080
...
Call Trace:
[<ffffffff80de37ec>] netif_carrier_off+0xc/0x58
[<ffffffff80c7804c>] phy_state_machine+0x48c/0x4f8
[<ffffffff808a1708>] process_one_work+0x158/0x368
[<ffffffff808a1ac0>] worker_thread+0x150/0x4c0
[<ffffffff808a8598>] kthread+0xc8/0xe0
[<ffffffff808617f0>] ret_from_kernel_thread+0x14/0x1c
The original motivation for this change originated from Marc Gonzales
indicating that his network driver did not have its adjust_link callback
executing with phydev->link = 0 while he was expecting it.
PHYLIB has never made any such guarantees ever because phy_stop() merely just
tells the workqueue to move into PHY_HALTED state which will happen
asynchronously.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: David Daney <ddaney.cavm@gmail.com>
Fixes: 7ad813f208 ("net: phy: Correctly process PHY_HALTED in phy_stop_machine()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f3086868e ]
Passing commands for logging to t4_record_mbox() with size
MBOX_LEN, when the actual command size is actually smaller,
causes out-of-bounds stack accesses in t4_record_mbox() while
copying command words here:
for (i = 0; i < size / 8; i++)
entry->cmd[i] = be64_to_cpu(cmd[i]);
Up to 48 bytes from the stack are then leaked to debugfs.
This happens whenever we send (and log) commands described by
structs fw_sched_cmd (32 bytes leaked), fw_vi_rxmode_cmd (48),
fw_hello_cmd (48), fw_bye_cmd (48), fw_initialize_cmd (48),
fw_reset_cmd (48), fw_pfvf_cmd (32), fw_eq_eth_cmd (16),
fw_eq_ctrl_cmd (32), fw_eq_ofld_cmd (32), fw_acl_mac_cmd(16),
fw_rss_glb_config_cmd(32), fw_rss_vi_config_cmd(32),
fw_devlog_cmd(32), fw_vi_enable_cmd(48), fw_port_cmd(32),
fw_sched_cmd(32), fw_devlog_cmd(32).
The cxgb4vf driver got this right instead.
When we call t4_record_mbox() to log a command reply, a MBOX_LEN
size can be used though, as get_mbox_rpl() will fill cmd_rpl up
completely.
Fixes: 7f080c3f2f ("cxgb4: Add support to enable logging of firmware mailbox commands")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b4e946ce1 ]
There is a deadlock possible when canceling the link status
delayed work queue. The removal process is run with RTNL held,
and the link status callback is acquring RTNL.
Resolve the issue by using trylock and rescheduling.
If cancel is in process, that block it from happening.
Fixes: 122a5f6410 ("staging: hv: use delayed_work for netvsc_send_garp()")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e58f95831e ]
gcc-8.0.0 (snapshot) points out that we copy a variable-length string
into a fixed length field using memcpy() with the destination length,
and that ends up copying whatever follows the string:
inlined from 'ql_core_dump' at drivers/net/ethernet/qlogic/qlge/qlge_dbg.c:1106:2:
drivers/net/ethernet/qlogic/qlge/qlge_dbg.c:708:2: error: 'memcpy' reading 15 bytes from a region of size 14 [-Werror=stringop-overflow=]
memcpy(seg_hdr->description, desc, (sizeof(seg_hdr->description)) - 1);
Changing it to use strncpy() will instead zero-pad the destination,
which seems to be the right thing to do here.
The bug is probably harmless, but it seems like a good idea to address
it in stable kernels as well, if only for the purpose of building with
gcc-8 without warnings.
Fixes: a61f802613 ("qlge: Add ethtool register dump function.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1a50c8e4c ]
Junote Cai reported that he was not able to get a DSA setup involving the
Freescale DPAA/FMAN driver to work and narrowed it down to
of_find_net_device_by_node(). This function requires the network device's
device reference to be correctly set which is the case here, though we have
lost any device_node association there.
The problem is that dpaa_eth_add_device() allocates a "dpaa-ethernet" platform
device, and later on dpaa_eth_probe() is called but SET_NETDEV_DEV() won't be
propagating &pdev->dev.of_node properly. Fix this by inherenting both the parent
device and the of_node when dpaa_eth_add_device() creates the platform device.
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78362998f5 ]
This helps tools such as wpa_supplicant can start even if the macsec
module isn't loaded yet.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b5dde2d62 upstream.
mwifiex records information about various channels as it receives scan
information. It does this by appending to a buffer that was sized
to the max number of supported channels on any band, but there are
numerous problems:
(a) scans can return info from more than one band (e.g., both 2.4 and 5
GHz), so the determined "max" is not large enough
(b) some firmware appears to return multiple results for a given
channel, so the max *really* isn't large enough
(c) there is no bounds checking when stashing these stats, so problems
(a) and (b) can easily lead to buffer overflows
Let's patch this by setting a slightly-more-correct max (that accounts
for a combination of both 2.4G and 5G bands) and adding a bounds check
when writing to our statistics buffer.
Due to problem (b), we still might not properly report all known survey
information (e.g., with "iw <dev> survey dump"), since duplicate results
(or otherwise "larger than expected" results) will cause some
truncation. But that's a problem for a future bugfix.
(And because of this known deficiency, only log the excess at the WARN
level, since that isn't visible by default in this driver and would
otherwise be a bit too noisy.)
Fixes: bf35443314 ("mwifiex: channel statistics support for mwifiex")
Cc: Avinash Patil <patila@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f7a5e13e8 upstream.
We have a new PCI subsystem ID for 7265D. Add it to the list.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc81bab5ee upstream.
_rtl_pci_find_adapter fail path will jump to label fail3 for
unsupported adapter types.
However, on course for fail3 there will be call rtl_deinit_core
before rtl_init_core.
For the inclusion of checking pci_iounmap this fail can be moved to
fail2.
Fixes
[ 4.492963] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 4.493067] IP: rtl_deinit_core+0x31/0x90 [rtlwifi]
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f35a7f91f6 upstream.
The rx ring buffers are added to a hash table if
firmware support full rx reorder. If the full rx
reorder support flag is not set before allocating
the rx ring buffers, none of the buffers are added
to the hash table.
There is a race condition between rx ring refill and
rx buffer replenish from napi poll. The interrupts are
enabled in hif start, before the rx ring is refilled during init.
We replenish buffers from napi poll due to the interrupts which
get enabled after hif start. Hence before the entire rx ring is
refilled during the init, the napi poll replenishes a few buffers
in steps of 100 buffers per attempt. During this rx ring replenish
from napi poll, the rx reorder flag has not been set due to which
the replenished buffers are not added to the hash table
Set the rx full reorder support flag before we allocate
the rx ring buffer to avoid the memory leak.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f17581788 upstream.
gcc 7 complains:
drivers/net/wireless/intersil/p54/fwio.c: In function 'p54_scan':
drivers/net/wireless/intersil/p54/fwio.c:491:4: warning: 'memset' used with length equal to number of elements without multiplication by element size [-Wmemset-elt-size]
Fix that by passing the correct size to memset.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca3d89a3eb ]
enable_4k_uar module parameter was added in patch cited below to
address the backward compatibility issue in SRIOV when the VM has
system's PAGE_SIZE uar implementation and the Hypervisor has 4k uar
implementation.
The above compatibility issue does not exist in the non SRIOV case.
In this patch, we always enable 4k uar implementation if SRIOV
is not enabled on mlx4's supported cards.
Fixes: 76e39ccf9c ("net/mlx4_core: Fix backward compatibility on VFs")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eac2c68d66 ]
The while loop that performs the dma page unmapping never decrements
index counter f and hence loops forever. Fix this with a pre-decrement
on f.
Detected by CoverityScan, CID#1357309 ("Infinite loop")
Fixes: 4c3523623d ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bed9ff1659 upstream.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e718fe450e ]
if the NIC fails to validate the checksum on TCP/UDP, and validation of IP
checksum is successful, the driver subtracts the pseudo-header checksum
from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't
do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails.
V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: f8c6455bb0 ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0a0e1a85c8 ]
Commit e5dadc65f9 ("ppp: Fix false xmit recursion detect with two ppp
devices") dropped the xmit_recursion counter incrementation in
ppp_channel_push() and relied on ppp_xmit_process() for this task.
But __ppp_channel_push() can also send packets directly (using the
.start_xmit() channel callback), in which case the xmit_recursion
counter isn't incremented anymore. If such packets get routed back to
the parent ppp unit, ppp_xmit_process() won't notice the recursion and
will call ppp_channel_push() on the same channel, effectively creating
the deadlock situation that the xmit_recursion mechanism was supposed
to prevent.
This patch re-introduces the xmit_recursion counter incrementation in
ppp_channel_push(). Since the xmit_recursion variable is now part of
the parent ppp unit, incrementation is skipped if the channel doesn't
have any. This is fine because only packets routed through the parent
unit may enter the channel recursively.
Finally, we have to ensure that pch->ppp is not going to be modified
while executing ppp_channel_push(). Instead of taking this lock only
while calling ppp_xmit_process(), we now have to hold it for the full
ppp_channel_push() execution. This respects the ppp locks ordering
which requires locking ->upl before ->downl.
Fixes: e5dadc65f9 ("ppp: Fix false xmit recursion detect with two ppp devices")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e5dadc65f9 ]
The global percpu variable ppp_xmit_recursion is used to detect the ppp
xmit recursion to avoid the deadlock, which is caused by one CPU tries to
lock the xmit lock twice. But it would report false recursion when one CPU
wants to send the skb from two different PPP devices, like one L2TP on the
PPPoE. It is a normal case actually.
Now use one percpu member of struct ppp instead of the gloable variable to
detect the xmit recursion of one ppp device.
Fixes: 55454a5658 ("ppp: avoid dealock on recursive xmit")
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: Liu Jianying <jianying.liu@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b9a88a390 upstream.
The PHY library does not deal very well with bind and unbind events. The first
thing we would see is that we were not properly canceling the PHY state machine
workqueue, so we would be crashing while dereferencing phydev->drv since there
is no driver attached anymore.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5bae8c0310 ]
We must re-enable RoCE on the e-switch management port (PF) only after destroying
the FDB in its switchdev/offloaded mode. Otherwise, when encapsulation is supported,
this re-enablement will fail.
Also, it's more natural and symmetric to disable RoCE on the PF before we create
the FDB under switchdev mode, so do that as well and revert if getting into error
during the mode change later.
Fixes: 9da34cd34e ('net/mlx5: Disable RoCE on the e-switch management [..]')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 811a919135 ]
While in RUNNING state, phy_state_machine() checks for link changes by
comparing phydev->link before and after calling phy_read_status().
This works as long as it is guaranteed that phydev->link is never
changed outside the phy_state_machine().
If in some setups this happens, it causes the state machine to miss
a link loss and remain RUNNING despite phydev->link being 0.
This has been observed running a dsa setup with a process continuously
polling the link states over ethtool each second (SNMPD RFC-1213
agent). Disconnecting the link on a phy followed by a ETHTOOL_GSET
causes dsa_slave_get_settings() / dsa_slave_get_link_ksettings() to
call phy_read_status() and with that modify the link status - and
with that bricking the phy state machine.
This patch adds a fail-safe check while in RUNNING, which causes to
move to CHANGELINK when the link is gone and we are still RUNNING.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f5992b72eb ]
The driver's ndo_get_stats64() method is not always called under RTNL.
So it can race with driver close or ethtool reconfigurations. Fix the
race condition by taking tp->lock spinlock in tg3_free_consistent()
when freeing the tp->hw_stats memory block. tg3_get_stats64() is
already taking tp->lock.
Reported-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ca7d1ca77 ]
For proper IRQ generation by DP83867 phy the INT/PWDN pin has to be
programmed as an interrupt output instead of a Powerdown input in
Configuration Register 3 (CFG3), Address 0x001E, bit 7 INT_OE = 1. The
current driver doesn't do this and as result IRQs will not be generated by
DP83867 phy even if they are properly configured in DT.
Hence, fix IRQ generation by properly configuring CFG3.INT_OE bit and
ensure that Link Status Change (LINK_STATUS_CHNG_INT) and Auto-Negotiation
Complete (AUTONEG_COMP_INT) interrupt are enabled. After this the DP83867
driver will work properly in interrupt enabled mode.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f1f9cbc04 ]
The R8A7740 GEther controller supports the packet checksum offloading
but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740
data, thus CSMR isn't cleared...
Fixes: 73a0d90730 ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 978d3639fd ]
As the SH77{34|63} manuals are freely available, I've checked the EESIPR
values written against the manuals, and they appeared to set the reserved
bits 11-15 (which should be 0 on write). Fix those EESIPR values.
Fixes: 380af9e390 ("net: sh_eth: CPU dependency code collect to "struct sh_eth_cpu_data"")
Fixes: f5d12767c8 ("sh_eth: get SH77{34|63} support out of #ifdef")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dfa523ae9f ]
Add a flag to indicate if a queue is rate-limited. Test the flag in
NAPI poll handler and avoid rescheduling the queue if true, otherwise
we risk locking up the host. The rescheduling will be done in the
timer callback function.
Reported-by: Jean-Louis Dupond <jean-louis@dupond.be>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Tested-by: Jean-Louis Dupond <jean-louis@dupond.be>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7ad813f208 ]
Marc reported that he was not getting the PHY library adjust_link()
callback function to run when calling phy_stop() + phy_disconnect()
which does not indeed happen because we set the state machine to
PHY_HALTED but we don't get to run it to process this state past that
point.
Fix this with a synchronous call to phy_state_machine() in order to have
the state machine actually act on PHY_HALTED, set the PHY device's link
down, turn the network device's carrier off and finally call the
adjust_link() function.
Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Fixes: a390d1f379 ("phylib: convert state_queue work to delayed_work")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f08c39ed0b ]
This is done in order to ensure that work will not run after the cleanup.
Fixes: ef9814deaf ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d439c84509 ]
The overflow_period is calculated in seconds. In order to use it
for delayed work scheduling translation to jiffies is needed.
Fixes: ef9814deaf ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0242f4a0bb ]
outer_header_zero() routine checks if the outer_headers match of a
flow-table entry are all zero.
This function uses the size of whole fte_match_param, instead of just
the outer_headers member, causing failure to detect all-zeros if
any other members of the fte_match_param are non-zero.
Use the correct size for zero check.
Fixes: 6dc6071cfc ("net/mlx5e: Add ethtool flow steering support")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 219c81f7d1 ]
When driver fail to allocate an entry to send command to FW, it must
notify the calling function and release the memory allocated for
this command.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dc798b4cc0 ]
The tx_enabled lag event field is used to determine whether a slave is
active.
Current logic uses this value only if the mode is active-backup.
However, LACP mode, although considered a load balancing mode, can mark
a slave as inactive in certain situations (e.g., LACP timeout).
This fix takes the tx_enabled value into account when remapping, with
no respect to the LAG mode (this should not affect the behavior in XOR
mode, since in this mode both slaves are marked as active).
Fixes: 7907f23adc (net/mlx5: Implement RoCE LAG feature)
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4813497b53 ]
Before commit bf8f6952a2 ("Add blurb about RGMII") it was unclear
whose responsibility it was to insert the required clock skew, and
in hindsight, some PHY drivers got it wrong. The solution forward
is to introduce a new property, explicitly requiring skew from the
node to which it is attached. In the interim, this driver will handle
all 4 RGMII modes identically (no skew).
Fixes: 52dfc83012 ("net: ethernet: add driver for Aurora VLSI NB8800 Ethernet controller")
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9476d39366 ]
DMA transfers are not allowed to buffers that are on the stack.
Therefore allocate a buffer to store the result of usb_control_message().
Fixes these bugreports:
https://bugzilla.kernel.org/show_bug.cgi?id=195217https://bugzilla.redhat.com/show_bug.cgi?id=1421387https://bugzilla.redhat.com/show_bug.cgi?id=1427398
Shortened kernel backtrace from 4.11.9-200.fc25.x86_64:
kernel: ------------[ cut here ]------------
kernel: WARNING: CPU: 3 PID: 2957 at drivers/usb/core/hcd.c:1587
kernel: transfer buffer not dma capable
kernel: Call Trace:
kernel: dump_stack+0x63/0x86
kernel: __warn+0xcb/0xf0
kernel: warn_slowpath_fmt+0x5a/0x80
kernel: usb_hcd_map_urb_for_dma+0x37f/0x570
kernel: ? try_to_del_timer_sync+0x53/0x80
kernel: usb_hcd_submit_urb+0x34e/0xb90
kernel: ? schedule_timeout+0x17e/0x300
kernel: ? del_timer_sync+0x50/0x50
kernel: ? __slab_free+0xa9/0x300
kernel: usb_submit_urb+0x2f4/0x560
kernel: ? urb_destroy+0x24/0x30
kernel: usb_start_wait_urb+0x6e/0x170
kernel: usb_control_msg+0xdc/0x120
kernel: mcs_get_reg+0x36/0x40 [mcs7780]
kernel: mcs_net_open+0xb5/0x5c0 [mcs7780]
...
Regression goes back to 4.9, so it's a good candidate for -stable.
Though it's the decision of the maintainer.
Thanks to Dan Williams for adding the "transfer buffer not dma capable"
warning in the first place. It instantly pointed me in the right direction.
Patch has been tested with transferring data from a Polar watch.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit be35e8c516 ]
The BCM53125 entry was missing an arl_entries member which would
basically prevent the ARL search from terminating properly. This switch
has 4 ARL entries, so add that.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f5d03143d upstream.
Due to a bugfix in wireless tree and the commit mentioned below a merge
was needed which went haywire. So the submitted change resulted in the
function brcmf_sdiod_sgtable_alloc() being called twice during the probe
thus leaking the memory of the first call.
Fixes: 4d79289598 ("brcmfmac: switch to new platform data")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b0f934e92 upstream.
iwlagn_check_ratid_empty takes the tid as a parameter, but
it doesn't check that it is not IWL_TID_NON_QOS.
Since IWL_TID_NON_QOS = 8 and iwl_priv::tid_data is an array
with 8 entries, accessing iwl_priv::tid_data[IWL_TID_NON_QOS]
is a bad idea.
This happened in iwlagn_rx_reply_tx. Since
iwlagn_check_ratid_empty is relevant only to check whether
we can open A-MPDU, this flow is irrelevant if tid is
IWL_TID_NON_QOS. Call iwlagn_check_ratid_empty only inside
the
if (tid != IWL_TID_NON_QOS)
a few lines earlier in the function.
Reported-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Tested-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71eae1ca77 ]
The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25
(bits 0-15 usually used for that are occupied by the packet checksum).
Thus we need to set the 'shift_rd0' field in the SH7734 SoC data...
Fixes: f0e81fecd4 ("net: sh_eth: Add support SH7734")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63dfb0dac9 ]
The USB core may call reset_resume when it fails to resume asix device.
And USB core can recovery this abnormal resume at low level driver,
the same .resume at asix driver can work too. Add .reset_resume can
avoid disconnecting after backing from system resume, and NFS can
still be mounted after this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 096de2f83e ]
When VXLAN offloading is enabled, be_features_check() tries to check if
an encapsulated packet is indeed a VXLAN packet. The check is not strict
enough, and considers any UDP-encapsulated ethernet frame with a 8-byte
tunnel header as being VXLAN. Unfortunately, both GENEVE and VXLAN-GPE
have a 8-byte header, so they get through this check.
Force the UDP destination port to be the one that has been offloaded to
hardware.
Without this, GENEVE-encapsulated packets can end up having an incorrect
checksum when both a GENEVE and a VXLAN (offloaded) tunnel are
configured.
This is similar to commit a547224dce ("mlx4e: Do not attempt to
offload VXLAN ports that are unrecognized").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10b1c04e92 ]
Demoting simple flow steering rule priority (for DPDK) was achieved by
wrapping FW commands MLX4_QP_FLOW_STEERING_ATTACH/DETACH for the PF
as well, and forcing the priority to MLX4_DOMAIN_NIC in the wrapper
function for the PF and all VFs.
In function mlx4_ib_create_flow(), this change caused the main rule
creation for the PF to be wrapped, while it left the associated
tunnel steering rule creation unwrapped for the PF.
This mismatch caused rule deletion failures in mlx4_ib_destroy_flow()
for the PF when the detach wrapper function did not find the associated
tunnel-steering rule (since creation of that rule for the PF did not
go through the wrapper function).
Fix this by setting MLX4_QP_FLOW_STEERING_ATTACH/DETACH to be "native"
(so that the PF invocation does not go through the wrapper), and perform
the required priority demotion for the PF in the mlx4_ib_create_flow()
code path.
Fixes: 48564135cb ("net/mlx4_core: Demote simple multicast and broadcast flow steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c1d5f8ff80 ]
This patch removes BUG_ON() macro from mlx4_alloc_icm_coherent()
by checking DMA address alignment in advance and performing proper
folding in case of error.
Fixes: 5b0bf5e25e ("mlx4_core: Support ICM tables in coherent memory")
Reported-by: Ozgur Karatas <okaratas@member.fsf.org>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b01fe7f91 ]
mlx4_QP_FLOW_STEERING_DETACH_wrapper first removes the steering
rule (which results in freeing the rule structure), and then
references a field in this struct (the qp number) when releasing the
busy-status on the rule's qp.
Since this memory was freed, it could reallocated and changed.
Therefore, the qp number in the struct may be incorrect,
so that we are releasing the incorrect qp. This leaves the rule's qp
in the busy state (and could possibly release an incorrect qp as well).
Fix this by saving the qp number in a local variable, for use after
removing the steering rule.
Fixes: 2c473ae7e5 ("net/mlx4_core: Disallow releasing VF QPs which have steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9da34cd34e ]
Under the switchdev/offloads mode, packets that don't match any
e-switch steering rule are sent towards the e-switch management
port. We use a NIC HW steering rule set per vport (uplink and VFs)
to make them be received into the host OS through the respective
vport representor netdevice.
Currnetly such missed RoCE packets will not get to this NIC steering
rule, and hence VF RoCE will not work over the slow path of the offloads
mode. This is b/c these packets will be matched by a steering rule added
by the firmware that serves RoCE traffic set on the PF NIC vport which
is also the e-switch management port under SRIOV.
Disabling RoCE on the e-switch management vport when we are in the offloads
mode, will signal to the firmware to remove their RoCE rule, and then the
missed RoCE packets will be matched by the representor NIC steering rule
as any other missed packets.
To achieve that, we disable RoCE on the PF vport. We do that by removing
(hot-unplugging) the IB device instance associated with the PF. This is
also required by our current model where the PF serves as the uplink
representor and hence only SW switching (TC, bridge, OVS) applications
and slow path vport mlx5e net-device should be running over that vport.
Fixes: c930a3ad74 ('net/mlx5e: Add devlink based SRIOV mode changes')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 610c908773 ]
This chip is the same as RTL8168, but its device id is 0x8161.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfb5b098e0 upstream.
When FW crashes with no_fw_recovery option, driver
waits for manual recovery with wil->mutex held, this
can easily create deadlocks.
Fix the problem by moving the wait outside the lock.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0878fff1f4 upstream.
The Generic PHY driver is a catch-all PHY driver and it should preserve
whatever prior initialization has been done by boot loader or firmware
agents. For specific PHY device configuration it is expected that a
specialized PHY driver would take over that role.
Resetting the generic PHY was a bad idea that has lead to several
complaints and downstream workarounds e.g: in OpenWrt/LEDE so restore
the behavior prior to 87aa9f9c61 ("net: phy: consolidate PHY
reset in phy_init_hw()").
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
