commit 3587c85667 upstream.
I've found that by just turning the chip on and off via the
POWER_DOWN register, I end up getting i2c_transfer errors on
HiKey.
Investigating further, it turns out that some of the register
state in hardware is getting lost, as the device registers are
reset when the chip is powered down.
Thus this patch simply re-writes the i2c address to the
ADV7511_REG_EDID_I2C_ADDR register to ensure its properly set
before we try to read the EDID data.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-7-git-send-email-john.stultz@linaro.org
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4226d9b127 upstream.
Thus this patch changes the EDID probing logic so that we
re-use the __adv7511_power_on/off() calls instead of duplciating
logic.
This does change behavior slightly as it adds the HPD signal
pulse to the EDID probe path, but Archit has had a patch to
add HPD signal pulse to the EDID probe path before, so this
should address the cases where that helped. Another difference
is that regcache_mark_dirty() is also called in the power off
path once EDID is probed.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-6-git-send-email-john.stultz@linaro.org
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 651e4769ba upstream.
In chasing down issues with EDID probing, I found some
duplicated but incomplete logic used to power the chip on and
off.
This patch refactors the adv7511_power_on/off functions, so
they can be used for internal needs.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-5-git-send-email-john.stultz@linaro.org
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cef75036c4 upstream.
This is an extension of Commit 7c20d213dd ("drm/vmwgfx: Work
around mode set failure in 2D VMs")
With Wayland desktop and atomic mode set, during the mode setting
process there is a moment when two framebuffer sized surfaces
are being pinned. This was not an issue with Xorg.
Since this only happens during a mode change, there should be no
performance impact by increasing allowable mem_size.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8777b927b9 upstream.
The original intent was to preserve watermarks as much as possible
in intel_pipe_wm.raw_wm, and put the validated ones in intel_pipe_wm.wm.
It seems this approach is insufficient and we don't always preserve
the raw watermarks, so just use the atomic iterator we're already using
to get a const pointer to all bound planes on the crtc.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102373
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171019151341.4579-1-maarten.lankhorst@linux.intel.com
(cherry picked from commit 28283f4f35)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c7ffa59cf0 ]
When updating the rotation fields, one of the assignments zeroes out the
rest of the register fields, which include settings for chroma siting,
inverse gamma, AMBA AXI caching, and alpha blending.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e41456bfc8 ]
The size computations done in the ioctl function use an integer.
If userspace submits a request with req->cmd_nr or req->cmd_buf_nr
set to INT_MAX, the integer computations overflow later, leading
to potential (kernel) memory corruption.
Prevent this issue by enforcing a limit on the number of submitted
commands, so that we have enough headroom later for the size
computations.
Note that this change has no impact on the currently available
users in userspace, like e.g. libdrm/exynos.
While at it, also make a comment about the size computation more
detailed.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ef15d36154 ]
clk_prepare_enable() may fail, so we should better check its return
value.
Also place the of_node_put() function right after clk_prepare_enable(),
in order to avoid calling of_node_put() twice in case clk_prepare_enable()
fails.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65e9310889 upstream.
We recently added an integer overflow check but it needs an additional
tweak to work properly on 32 bit systems.
The problem is that we're doing the right hand side of the assignment as
type unsigned long so the max it will have an integer overflow instead
of being larger than SIZE_MAX. That means the "sz > SIZE_MAX" condition
is never true even on 32 bit systems. We need to first cast it to u64
and then do the math.
Fixes: 4a630fadbb ("drm/msm: Fix potential buffer overflow issue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a630fadbb upstream.
In function submit_create, if nr_cmds or nr_bos is assigned with
negative value, the allocated buffer may be small than intended.
Using this buffer will lead to buffer overflow issue.
Signed-off-by: Kasin Li <donglil@codeaurora.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c838e2a9b upstream.
Per my reading of the eDP spec, DP_DPCD_DISPLAY_CONTROL_CAPABLE bit in
DP_EDP_CONFIGURATION_CAP should be set if the eDP display control
registers starting at offset DP_EDP_DPCD_REV are "enabled". Currently we
check the bit before reading the registers, and DP_EDP_DPCD_REV is the
only way to detect eDP revision.
Turns out there are (likely buggy) displays that require eDP 1.4+
features, such as supported link rates and link rate select, but do not
have the bit set. Read the display control registers
unconditionally. They are supposed to read zero anyway if they are not
supported, so there should be no harm in this.
This fixes the referenced bug by enabling the eDP version check, and
thus reading of the supported link rates. The panel in question has 0 in
DP_MAX_LINK_RATE which is only supported in eDP 1.4+. Without the
supported link rates method we default to RBR which is insufficient for
the panel native mode. As a curiosity, the panel also has a bogus value
of 0x12 in DP_EDP_DPCD_REV, but that passes our check for >= DP_EDP_14
(which is 0x03).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103400
Reported-and-tested-by: Nicolas P. <issun.artiste@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171026142932.17737-1-jani.nikula@intel.com
(cherry picked from commit 0501a3b0eb)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb4b02d7ca upstream.
Fixes init failures on polaris cards with harvested UVD.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b95f4f730 upstream.
refresh_rate was not initialized when program
display gap.
this patch can fix vce ring test failed
when do S3 on Polaris10.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=103102
bug: https://bugzilla.kernel.org/show_bug.cgi?id=196615
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77913bbcb4 upstream.
Even though we've zeroed the PDE, the GPU may have cached the PD, so we
need to flush when deleting them.
Noticed while working on replacement MMU code, but a backport might be a
good idea, so let's fix it in the current code too.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 194d68dd05 upstream.
G92's seem to require some additional bit of initialization before the
BSP engine can work. It feels like clocks are not set up for the
underlying VLD engine, which means that all commands submitted to the
xtensa chip end up hanging. VP seems to work fine though.
This still allows people to force-enable the bsp engine if they want to
play around with it, but makes it harder for the card to hang by
default.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4694335dad ]
When the fast blit path fails while attempting to move a buffer from RAM
to VRAM, we fall back to a CPU-based memcpy that cannot handle split VRAM
buffers. Instead of crashing, simply fail the buffer move.
Ideally, we would teach TTM about split buffers so that the fallback still
works in this case, but that is quite involved. So for now, apply the
simplest possible fix.
Fixes: 40361bb1704b ("drm/amdgpu: add VRAM manager v2")
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea850f64c2 upstream.
While technically CHV isn't DDI, we do look at the VBT based DDI port
info for HDMI DDC pin and DP AUX channel. (We call these "alternate",
but they're really just something that aren't platform defaults.)
In commit e4ab73a132 ("drm/i915: Respect alternate_ddc_pin for all DDI
ports") Ville writes, "IIRC there may be CHV system that might actually
need this."
I'm not sure why there couldn't be even more platforms that need this,
but start conservative, and parse the info for CHV in addition to DDI.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100553
Reported-by: Marek Wilczewski <mw@3cte.pl>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d0815082cb98487618429b62414854137049b888.1506586821.git.jani.nikula@intel.com
(cherry picked from commit 348e4058eb)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b50f7b24c upstream.
intel_crtc->config->cpu_transcoder isn't yet filled out when
intel_crtc_mode_get() gets called during output probing, so we should
not use it there. Instead intel_crtc_mode_get() figures out the correct
transcoder on its own, and that's what we should use.
If the BIOS boots LVDS on pipe B, intel_crtc_mode_get() would actually
end up reading the timings from pipe A instead (since PIPE_A==0),
which clearly isn't what we want.
It looks to me like this may have been broken by
commit eccb140bca ("drm/i915: hw state readout&check support for cpu_transcoder")
as that one removed the early initialization of cpu_transcoder from
intel_crtc_init().
Cc: dri-devel@lists.freedesktop.org
Cc: Rob Kramer <rob@solution-space.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: Rob Kramer <rob@solution-space.com>
Fixes: eccb140bca ("drm/i915: hw state readout&check support for cpu_transcoder")
References: https://lists.freedesktop.org/archives/dri-devel/2016-April/104142.html
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1459525046-19425-1-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit e30a154b52)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7ba25bd9e upstream.
Kernel stores the time in jiffies at which the eDP panel is turned
off. This should be obtained after the panel is off (after the
wait_panel_off). When we next attempt to turn the panel on, we use the
difference between the timestamp at which we want to turn the panel on
and timestamp at which panel was turned off to ensure that this is equal
to panel power cycle delay and if not we wait for the remaining
time. Not waiting for the panel power cycle delay can cause the panel to
not turn on giving rise to AUX timeouts for the attempted AUX
transactions.
v2:
* Separate lines for bugzilla (Jani Nikula)
* Suggested by tag (Daniel Vetter)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101518
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101144
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507135706-17147-1-git-send-email-manasi.d.navare@intel.com
(cherry picked from commit cbacf02e77)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ba7d7e043 upstream.
The hardware state readout oopses after several warnings when trying to
use HDMI on port A, if such a combination is configured in VBT. Filter
the combo out already at the VBT parsing phase.
v2: also ignore DVI (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102889
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Daniel Drake <dan@reactivated.net>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170921141920.18172-1-jani.nikula@intel.com
(cherry picked from commit d27ffc1d00)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7916efe5b5 ]
The horizontal and vertical flip flags were the wrong way around,
causing reflect-x to result in reflect-y being applied and vice-versa.
Fix them.
Fixes: ad49f8602f ("drm/arm: Add support for Mali Display Processors")
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit edabb3c4cd ]
The destination rectangle provided by userspace in the CRTC_X/Y/W/H
properties is already expressed as the dimensions after rotation.
This means we shouldn't swap the width and height ourselves when a
90/270 degree rotation is requested, so remove the code doing the swap.
Fixes: ad49f8602f ("drm/arm: Add support for Mali Display Processors")
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8bf793883d ]
In function kfd_wait_on_events(), when the call to copy_from_user()
fails, the value of return variable ret is 0. 0 indicates success, which
is inconsistent with the execution status. This patch fixes the bug by
assigning "-EFAULT" to ret when copy_from_user() returns an unexpected
value.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 58d09ebdb4 ]
Do the overlay frontbuffer tracking properly so that it matches
the state of the overlay on/off/continue requests.
One slight problem is that intel_frontbuffer_flip_complete()
may get delayed by an arbitrarily liong time due to the fact that
the overlay code likes to bail out when a signal occurs. So the
flip may not get completed until the ioctl is restarted. But fixing
that would require bigger surgery, so I decided to ignore it for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481131693-27993-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 518417525f upstream.
All manipulations of the gem_object list need to be protected by
the list mutex, as GEM objects can be created and freed in parallel.
This fixes a kernel memory corruption.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8206085487 upstream.
Fixes a hibernation regression on APUs.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=191571
Fixes: 274ad65c9d (drm/radeon: hard reset r600 and newer GPU when hibernating.)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a596fc9d9 upstream.
The drm_driver lastclose callback is called when the last userspace
DRM client has closed. Call drm_fbdev_cma_restore_mode to restore
the fbdev console otherwise the fbdev console will stop working.
Fixes: 9026e0d122 ("drm: Add Allwinner A10 Display Engine support")
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[net147@gmail.com: Backport to 4.9, minor context change]
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d5104c5a6 upstream.
In chasing down a previous issue with EDID probing from calling
drm_helper_hpd_irq_event() from irq context, Laurent noticed
that the DRM documentation suggests that
drm_kms_helper_hotplug_event() should be used instead.
Thus this patch replaces drm_helper_hpd_irq_event() with
drm_kms_helper_hotplug_event(), which requires we update the
connector.status entry and only call _hotplug_event() when the
status changes.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-3-git-send-email-john.stultz@linaro.org
Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com>
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 518cb7057a upstream.
I was recently seeing issues with EDID probing, where
the logic to wait for the EDID read bit to be set by the
IRQ wasn't happening and the code would time out and fail.
Digging deeper, I found this was due to the fact that
IRQs were disabled as we were running in IRQ context from
the HPD signal.
Thus this patch changes the logic to handle the HPD signal
via a work_struct so we can be out of irq context.
With this patch, the EDID probing on hotplug does not time
out.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com>
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc60c90f47 upstream.
It appears that MSI does not work on either G5 PPC nor on a E5500-based
platform, where other hardware is reported to work fine with MSI.
Both tests were conducted with NV4x hardware, so perhaps other (or even
this) hardware can be made to work. It's still possible to force-enable
with config=NvMSI=1 on load.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9afae27192 upstream.
When fail to get needed page for pool, need to put allocated pages
into pool. But current code has a miscalculation of allocated pages,
correct it.
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd1adef3bf upstream.
The VSL and HSL bits in the DSMR register set the corresponding
horizontal and vertical sync signal polarity to active high. The code
got it the wrong way around, fix it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com>
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cdced8a39 upstream.
There is a bug in the setting of the DES (Display Enable Signal)
register. This current setting occurs 1 dot left shift. The DES
register should be set minus one value about the specifying value
with H/W specification. This patch corrects it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com>
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05ee29e94a upstream.
When an encoder fails to initialize the driver prints an error message
to the kernel log. The message contains the name of the encoder's DT
node, which is NULL for internal encoders. Use the of_node_full_name()
macro to avoid dereferencing a NULL pointer, print the output number to
add more context to the error, and make sure we still own a reference to
the encoder's DT node by delaying the of_node_put() call.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com>
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe4600a548 upstream.
This is the same bug as we fixed in commit f6cd7daecf ("drm: Release
driver references to handle before making it available again"), but now
the exposure is via the PRIME lookup tables. If we remove the
object/handle from the PRIME lut, then a new request for the same
object/fd will generate a new handle, thus for a short window that
object is known to userspace by two different handles. Fix this by
releasing the driver tracking before PRIME.
Fixes: 0ff926c7d4 ("drm/prime: add exported buffers to current fprivs
imported buffer list (v2)")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170819120558.6465-1-chris@chris-wilson.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6f756e09f upstream.
A relocation pointing to the last four bytes of a buffer can
legitimately happen in the case of small vertex buffers.
Signed-off-by: Wladimir J. van der Laan <laanwj@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71d3f6ef7f ]
virtio uses normal ram as backing storage for the framebuffer, so we
should assign the address to new screen_buffer (added by commit
17a7b0b4d9) instead of screen_base.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5694785cf0 upstream.
As I was staring at the si_init_golden_registers code, I noticed that
the Pitcairn initialization silently falls through the Cape Verde
initialization, and the Oland initialization falls through the Hainan
initialization. However there is no comment stating that this is
intentional, and the radeon driver doesn't have any such fallthrough,
so I suspect this is not supposed to happen.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 62a3755341 ("drm/amdgpu: add si implementation v10")
Cc: Ken Wang <Qingqing.Wang@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Marek Olšák" <maraeo@gmail.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a6cb3b864b ]
For every submission buffer object one of MSM_SUBMIT_BO_WRITE
and MSM_SUBMIT_BO_READ must be set (and nothing else). If we
allowed zero then the buffer object would never get queued to
be unreferenced.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6490abc4bc ]
The error cases in submit_reloc() need to put back the virtual
address of the bo before failling. Add a single failure path
for the function.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 88b333b0ed ]
Currently the value written to CP_RB_WPTR is calculated on the fly as
(rb->next - rb->start). But as the code is designed rb->next is wrapped
before writing the commands so if a series of commands happened to
fit perfectly in the ringbuffer, rb->next would end up being equal to
rb->size / 4 and thus result in an out of bounds address to CP_RB_WPTR.
The easiest way to fix this is to mask WPTR when writing it to the
hardware; it makes the hardware happy and the rest of the ringbuffer
math appears to work and there isn't any point in upsetting anything.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[squash in is_power_of_2() check]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f7b0d2638 upstream.
It isn't safe to call drm_dev_unregister() without first initializing
mode setting with drm_mode_config_init(). This leads to a crash if
either IO memory can't be remapped or vblank initialization fails.
Fix this by reordering the initialization sequence. Move vblank
initialization after the drm_mode_config_init() call, and move IO
remapping before drm_dev_alloc() to avoid the need to perform clean up
in case of failure.
While at it remove the explicit drm_vblank_cleanup() call from
rcar_du_remove() as the drm_dev_unregister() function already cleans up
vblank.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: thongsyho <thong.ho.px@rvc.renesas.com>
Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38bcb208f6 upstream.
Bit 30 being set causes the upper half of BAR2 to stay in physical mode,
mapped over the end of VRAM, even when the rest of the BAR has been set
to virtual mode.
We inherited our initial value from RM, but I'm not aware of any reason
we need to keep it that way.
This fixes severe GPU hang/lockup issues revealed by Wayland on F26.
Shout-out to NVIDIA for the quick response with the potential cause!
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a90e049cac upstream.
GP102's cursors go from chan 17..20. Increase the array size to hold
their data properly.
Fixes: e50fcff15f ("drm/nouveau/disp/gp102: fix cursor/overlay immediate channel indices")
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
