commit 9ea0c30760 upstream.
During init we take care of regulatory stuff by disabling all
unavailable channels (see brcmf_construct_chaninfo) so this predisabling
them is not really required (and this patch won't change any behavior).
It will on the other hand allow more detailed runtime control over
channels which is the main reason for this change.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Lambdadroid <lambdadroid@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1fe954b209 ]
FEC is configured by the NVM and the driver should not be
overriding it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2bf1a87b90 ]
The indirection table was reported incorrectly for X550 and newer
where we can support up to 64 RSS queues.
Reported-by Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f0d646b72 ]
A retry count of 10 is likely to run into problems on X550 devices that
have to detect and reset unresponsive CS4227 devices. So, reduce the I2C
retry count to 3 for X550 and above. This should avoid any possible
regressions in existing devices.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f215266470 ]
BaseT adapters that are capable of supporting 100Mb are not reporting this
capability. This patch corrects the reporting so that 100Mb is shown as
supported on those adapters.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f7f37e7ff2 ]
When an interface is part of a namespace it is possible that
ixgbe_close() may be called while __ixgbe_shutdown() is running
which ends up in a double free WARN and/or a BUG in free_msi_irqs().
To handle this situation we extend the rtnl_lock() to protect the
call to netif_device_detach() and ixgbe_clear_interrupt_scheme()
in __ixgbe_shutdown() and check for netif_device_present()
to avoid clearing the interrupts second time in ixgbe_close();
Also extend the rtnl lock in ixgbe_resume() to netif_device_attach().
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 126db13fa0 ]
Make sure that we free the IRQs in ixgbe_io_error_detected() when
responding to an PCIe AER error and also restore them when the
interface recovers from it.
Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
in the case where we call ixgbe_remove() after a failed recovery from
AER error because the interrupts were not freed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54f6d4c424 ]
This patch ensures that the advertised link speeds are configured
for X553 KR/KX backplane. Without this patch the link remains at
1G when resuming from low power after being downshifted by LPLU.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 76ed5a8f47 ]
Fix an if statement with hw_dbg lines where the logic was inverted with
regards to the corresponding return value used in the if statement.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9474933caf ]
Similar to ixgbe, when an interface is part of a namespace it is
possible that igb_close() may be called while __igb_shutdown() is
running which ends up in a double free WARN and/or a BUG in
free_msi_irqs().
Extend the rtnl_lock() to protect the call to netif_device_detach() and
igb_clear_interrupt_scheme() in __igb_shutdown() and check for
netif_device_present() to avoid calling igb_clear_interrupt_scheme() a
second time in igb_close().
Also extend the rtnl lock in igb_resume() to netif_device_attach().
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1827853354 ]
Several people have reported firmware leaving the I210/I211 PHY's page
select register set to something other than the default of zero. This
causes the first accesses, PHY_IDx register reads, to access something
else, resulting in device probe failure:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of 0000:01:00.0 failed with error -2
This problem began for them after a previous patch I submitted was
applied:
commit 2a3cdead8b
Author: Aaron Sierra <asierra@xes-inc.com>
Date: Tue Nov 3 12:37:09 2015 -0600
igb: Remove GS40G specific defines/functions
I personally experienced this problem after attempting to PXE boot from
I210 devices using this firmware:
Intel(R) Boot Agent GE v1.5.78
Copyright (C) 1997-2014, Intel Corporation
Resetting the PHY before reading from it, ensures the page select
register is in its default state and doesn't make assumptions about
the PHY's register set before the PHY has been probed.
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Cc: Chris Arges <carges@vectranetworks.com>
Cc: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Tested-by: Chris J Arges <christopherarges@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f3fc1e620 ]
Multiple IES API resets can cause a race condition where the mailbox
interrupt request bits can be cleared before being handled. This can
leave certain mailbox messages from the PF to be untreated and the PF
will enter in some inactive state. If this situation occurs, the IES API
will initiate a mailbox version reset which, then, trigger a mailbox
state change. Once this mailbox transition occurs (from OPEN to CONNECT
state), a request for reset will be returned.
This ensures that PF will undergo a reset whenever IES API encounters an
unknown global mailbox interrupt event or whenever the IES API
terminates.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9029679f66 upstream.
Upon stopping an AP interface the driver disable INFRA mode effectively
setting the interface in IBSS mode. However, this may affect other
interfaces running in INFRA mode. For instance, if user creates and stops
hostap daemon on virtual interface, then association cannot work on
primary interface because default BSS has been set to IBSS mode in
firmware side. The IBSS mode should be set when cfg80211 changes the
interface.
Reviewed-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <Chi-Hsien.Lin@cypress.com>
[kvalo@codeaurora.org: rephased commit log based on discussion]
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Philipp Rosenberger <p.rosenberger@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6151b8b37b ]
ppp_release() tries to ensure that netdevices are unregistered before
decrementing the unit refcount and running ppp_destroy_interface().
This is all fine as long as the the device is unregistered by
ppp_release(): the unregister_netdevice() call, followed by
rtnl_unlock(), guarantee that the unregistration process completes
before rtnl_unlock() returns.
However, the device may be unregistered by other means (like
ppp_nl_dellink()). If this happens right before ppp_release() calling
rtnl_lock(), then ppp_release() has to wait for the concurrent
unregistration code to release the lock.
But rtnl_unlock() releases the lock before completing the device
unregistration process. This allows ppp_release() to proceed and
eventually call ppp_destroy_interface() before the unregistration
process completes. Calling free_netdev() on this partially unregistered
device will BUG():
------------[ cut here ]------------
kernel BUG at net/core/dev.c:8141!
invalid opcode: 0000 [#1] SMP
CPU: 1 PID: 1557 Comm: pppd Not tainted 4.14.0-rc2+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014
Call Trace:
ppp_destroy_interface+0xd8/0xe0 [ppp_generic]
ppp_disconnect_channel+0xda/0x110 [ppp_generic]
ppp_unregister_channel+0x5e/0x110 [ppp_generic]
pppox_unbind_sock+0x23/0x30 [pppox]
pppoe_connect+0x130/0x440 [pppoe]
SYSC_connect+0x98/0x110
? do_fcntl+0x2c0/0x5d0
SyS_connect+0xe/0x10
entry_SYSCALL_64_fastpath+0x1a/0xa5
RIP: free_netdev+0x107/0x110 RSP: ffffc28a40573d88
---[ end trace ed294ff0cc40eeff ]---
We could set the ->needs_free_netdev flag on PPP devices and move the
ppp_destroy_interface() logic in the ->priv_destructor() callback. But
that'd be quite intrusive as we'd first need to unlink from the other
channels and units that depend on the device (the ones that used the
PPPIOCCONNECT and PPPIOCATTACH ioctls).
Instead, we can just let the netdevice hold a reference on its
ppp_file. This reference is dropped in ->priv_destructor(), at the very
end of the unregistration process, so that neither ppp_release() nor
ppp_disconnect_channel() can call ppp_destroy_interface() in the interim.
Reported-by: Beniamino Galvani <bgalvani@redhat.com>
Fixes: 8cb775bc0a ("ppp: fix device unregistration upon netns deletion")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5c25f65fd1 ]
If the name argument of dev_get_valid_name() contains "%d", it will try
to assign it a unit number in __dev__alloc_name() and return either the
unit number (>= 0) or an error code (< 0).
Considering positive values as error values prevent tun device creations
relying this mechanism, therefor we should only consider negative values
as errors here.
Signed-off-by: Julien Gomes <julien@arista.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78e0ea6791 ]
Double free of skb_array in tap module is causing kernel panic. When
tap_set_queue() fails we free skb_array right away by calling
skb_array_cleanup(). However, later on skb_array_cleanup() is called
again by tap_sock_destruct through sock_put(). This patch fixes that
issue.
Fixes: 362899b872 (macvtap: switch to use skb array)
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ad646c81b ]
register_netdevice() could fail early when we have an invalid
dev name, in which case ->ndo_uninit() is not called. For tun
device, this is a problem because a timer etc. are already
initialized and it expects ->ndo_uninit() to clean them up.
We could move these initializations into a ->ndo_init() so
that register_netdevice() knows better, however this is still
complicated due to the logic in tun_detach().
Therefore, I choose to just call dev_get_valid_name() before
register_netdevice(), which is quicker and much easier to audit.
And for this specific case, it is already enough.
Fixes: 96442e4242 ("tuntap: choose the txq based on rxq")
Reported-by: Dmitry Alexeev <avekceeb@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb5f0b3ef6 upstream.
The D_CAN controller doesn't provide a triple sampling mode, so don't set
the CAN_CTRLMODE_3_SAMPLES flag in ctrlmode_supported. Currently enabling
triple sampling is a no-op.
Signed-off-by: Richard Schütz <rschuetz@uni-koblenz.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f7116757b upstream.
The CANFD transmitter delay calculation formula was updated in the
latest software drop from IFI and improves the behavior of the IFI
CANFD core during bitrate switching. Use the new formula to improve
stability of the CANFD operation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Markus Marb <markus@marb.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dcf924c2e upstream.
SUN4Is CAN IP has a 64 byte deep FIFO buffer. If the buffer is not
drained fast enough (overrun) it's getting mangled. Already received
frames are dropped - the data can't be restored.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b02c20ce0 upstream.
Some firmwares in Huawei E3372H devices have been observed to switch back
to NTB 32-bit format after altsetting switch.
This patch implements a driver flag to check for the device settings and
set NTB format to 16-bit again if needed.
The flag has been activated for devices controlled by the huawei_cdc_ncm.c
driver.
V1->V2:
- fixed broken error checks
- some corrections to the commit message
V2->V3:
- variable name changes, to clarify what's happening
- check (and possibly set) the NTB format later in the common bind code path
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-and-tested-by: Christian Panton <christian@panton.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
CC: Bjørn Mork <bjorn@mork.no>
CC: Christian Panton <christian@panton.org>
CC: linux-usb@vger.kernel.org
CC: netdev@vger.kernel.org
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Porto Rio <porto.rio@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d536288822 ]
ieee80211_unregister_hw() might invoke operations to stop the interface,
that uses the hal_mutex. So don't destroy it until after we're done
using it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1701221696 ]
If we do not get TX status in reasonable time, we most likely fail to
send frame hence mark it as so.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab99063f87 ]
During bands setup we disable all channels that firmware doesn't support
in the current regulatory setup. If we do this before wiphy_register
it will result in copying set flags (including IEEE80211_CHAN_DISABLED)
to the orig_flags which is supposed to be persistent. We don't want this
as regulatory change may result in enabling some channels. We shouldn't
mess with orig_flags then (by changing them or ignoring them) so it's
better to just take care of their proper values.
This patch cleanups code a bit (by taking orig_flags more seriously) and
allows further improvements like disabling really unavailable channels.
We will need that e.g. if some frequencies should be disabled for good
due to hardware setup (design).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 259010c509 ]
Function lbs_cmd_802_11_sleep_params() always return 0, even if the call
to lbs_cmd_with_response() fails. In this case, the parameter @sp will
keep uninitialized. Because the return value is 0, its caller (say
lbs_sleepparams_read()) will not detect the error, and will copy the
uninitialized stack memory to user sapce, resulting in stack information
leak. To avoid the bug, this patch returns variable ret (which takes
the return value of lbs_cmd_with_response()) instead of 0.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188451
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56dd5af9bc ]
The default for the maximum number of tx/rx queues of one interface is
the number of cpus of the system today. As each queue pair reserves 512
grant pages this default consumes a ridiculous number of grants for
large guests.
Limit the queue number to 8 as default. This value can be modified
via a module parameter if required.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f4737a6203 ]
This method may be unsupported (see: USB bus) or may just fail (see:
SDIO bus).
While at it rework logic in brcmf_sdio_bus_get_memdump function to avoid
too many conditional code nesting levels.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f622593cc ]
With QCA4019 platform, SRAM address can be accessed directly from host but
currently, we are assuming sram addresses cannot be accessed directly and
hence we convert the addresses.
While there, clean up growing hw checks during conversion of target CPU
address to CE address. Now we have function pointer pertaining to different
chips.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ac6e058b75 ]
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.
To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).
To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.
Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"
https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d45cb20e12 ]
When we send a deauth to a station we don't know about, we
need to use the PROBE_RESP queue. This can happen when we
send a deauth to a station that is not associated to us.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7102a18ac3 ]
The timeouts were too agressive and sometimes cause false alarms.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9303ab2b34 ]
drivers/net/ethernet/marvell/mvneta.c:2694:26: error: storage size of 'status' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:26: error: storage size of 'changed' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:9: error: variable 'changed' has initializer but incomplete type
drivers/net/ethernet/marvell/mvneta.c:2709:2: error: implicit declaration of function 'fixed_phy_update_state' [-Werror=implicit-function-declaration]
Add linux/phy_fixed.h to mvneta.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1d2d1329a upstream.
To avoid kernel warning "Unhandled message (68)", ignore the
CMD_FLUSH_QUEUE_REPLY message for now.
As of Leaf v2 firmware version v4.1.844 (2017-02-15), flush tx queue is
synchronous. There is a capability bit indicating whether flushing tx
queue is synchronous or asynchronous.
A proper solution would be to query the device for capabilities. If the
synchronous tx flush capability bit is set, we should wait for
CMD_FLUSH_QUEUE_REPLY message, while flushing the tx queue.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f65a923e6 upstream.
If the return value from kvaser_usb_send_simple_msg() was non-zero, the
return value from kvaser_usb_flush_queue() was printed in the kernel
warning.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a379f5b36 upstream.
Fix loopback mode by setting the right flag and remove presume mode.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8b8b16352 upstream.
In commit 40b368af4b ("rtlwifi: Fix alignment issues"), the read
of REG_DBI_READ was changed from 16 to 8 bits. For unknown reasonsi
this change results in reduced stability for the wireless connection.
This regression was located using bisection.
Fixes: 40b368af4b ("rtlwifi: Fix alignment issues")
Reported-and-tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c503dd38f8 upstream.
With KASAN and a couple of other patches applied, this driver is one
of the few remaining ones that actually use more than 2048 bytes of
kernel stack:
broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function 'wlc_phy_workarounds_nphy_gainctrl':
broadcom/brcm80211/brcmsmac/phy/phy_n.c:16065:1: warning: the frame size of 3264 bytes is larger than 2048 bytes [-Wframe-larger-than=]
broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function 'wlc_phy_workarounds_nphy':
broadcom/brcm80211/brcmsmac/phy/phy_n.c:17138:1: warning: the frame size of 2864 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Here, I'm reducing the stack size by marking as many local variables as
'static const' as I can without changing the actual code.
This is the first of three patches to improve the stack usage in this
driver. It would be good to have this backported to stabl kernels
to get all drivers in 'allmodconfig' below the 2048 byte limit so
we can turn on the frame warning again globally, but I realize that
the patch is larger than the normal limit for stable backports.
The other two patches do not need to be backported.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd2349121b upstream.
The length of the data in the received skb is currently passed into
brcmf_fweh_process_event() as packet_len, but this value is not checked.
event_packet should be followed by DATALEN bytes of additional event
data. Ensure that the received packet actually contains at least
DATALEN bytes of additional data, to avoid copying uninitialized memory
into event->data.
Suggested-by: Mattias Nissler <mnissler@chromium.org>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72d92e865d upstream.
The dlc member of the struct rx_msg contains also the ESD_RTR flag to
mark received RTR frames. Without the fix the can_dlc value for received
RTR frames would always be set to 8 by get_can_dlc() instead of the
received value.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97819f9430 upstream.
If sending messages with no cable connected, it quickly happens that
there is no more TX context available. Then "gs_can_start_xmit()"
returns with "NETDEV_TX_BUSY" and the upper layer does retry
immediately keeping the CPU busy. To fix that issue, I moved
"atomic_dec(&dev->active_tx_urbs)" from "gs_usb_xmit_callback()" to
the TX done handling in "gs_usb_receive_bulk_callback()". Renaming
"active_tx_urbs" to "active_tx_contexts" and moving it into
"gs_[alloc|free]_tx_context()" would also make sense.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5212b943d ]
Currently the state is read only after the buffers are relesed.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c2dedf8773 ]
Reserving doorbell BAR space according to the currently active CPUs
may result in a bug if disabled CPUs are later enabled but no
doorbell space was reserved for them.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit afe981d664 ]
Driver currently utilizes the same loop variable in two
nested loops.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36fb7435b6 ]
The mvpp2_txq_bufs_free() function is called upon TX completion to DMA
unmap TX buffers, and free the corresponding SKBs. It gets the
references to the SKB to free and the DMA buffer to unmap from a per-CPU
txq_pcpu data structure.
However, the code currently increments the pointer to the next entry
before doing the DMA unmap and freeing the SKB. It does not cause any
visible problem because for a given SKB the TX completion is guaranteed
to take place on the CPU where the TX was started. However, it is much
more logical to increment the pointer to the next entry once the current
entry has been completely unmapped/released.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 95f1ba9a24 ]
In the VF driver, module parameter mlx4_log_num_mgm_entry_size was
mistakenly overwritten -- and in a manner which overrode the
device-managed flow steering option encoded in the parameter.
log_num_mgm_entry_size is a global module parameter which
affects all ConnectX-3 PFs installed on that host.
If a VF changes log_num_mgm_entry_size, this will affect all PFs
which are probed subsequent to the change (by disabling DMFS for
those PFs).
Fixes: 3c439b5586 ("mlx4_core: Allow choosing flow steering mode")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47d3a07528 ]
The cited commit makes a great job of finding optimal shift/multiplier
values assuming a 10 seconds wrap around, but forgot to change the
overflow_period computation.
It overflows in cyclecounter_cyc2ns(), and the final result is 804 ms,
which is silly.
Lets simply use 5 seconds, no need to recompute this, given how it is
supposed to work.
Later, we will use a timer instead of a work queue, since the new RX
allocation schem will no longer need mlx4_en_recover_from_oom() and the
service_task firing every 250 ms.
Fixes: 31c128b66e ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6f437d4319 ]
Commit 653d2ffd6405 ("qed*: Fix link indication race") introduced another
race - one of the inner functions called from the link-change flow is
explicitly using the slowpath context dedicated PTT instead of gaining
that PTT from the caller. Since this flow can now be called from
a different context as well, we're in risk of the PTT breaking.
Fixes: 653d2ffd6405 ("qed*: Fix link indication race")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff4dd73dd2 ]
Unfortunately, the nla policy was defined to have HWSIM_ATTR_RADIO_NAME
as an NLA_STRING, rather than NLA_NUL_STRING, so we can't use it as a
NUL-terminated string in the kernel.
Rather than break the API, kasprintf() the string to a new buffer to
guarantee NUL termination.
Reported-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
