This reverts commit 7336f5481f which is
commit a0085f2510 upstream.
It causes problems with working systems, as noted by a number of the
ChromeOS developers.
Cc: Sukumar Ghorai <sukumar.ghorai@intel.com>
Cc: Amit K Bag <amit.k.bag@intel.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Brian Norris <briannorris@chromium.org>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bff5bf9db1 upstream.
Sending the switch state change twice within the same frame is invalid
evdev protocol and only works if the client handles keys immediately as
well. Processing events immediately is incorrect, it forces a fake
order of events that does not exist on the device.
Recent versions of libinput changed to only process the device state and
SYN_REPORT time, so now the key event is lost.
https://bugs.freedesktop.org/show_bug.cgi?id=104041
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db2b033260 upstream.
The DT specifies a threshold of 65000, we setup the register with a value in
the temperature resolution for the controller, 64656.
When we reach 64656, the interrupt fires, the interrupt is disabled. Then the
irq thread runs and calls thermal_zone_device_update() which will call in turn
hisi_thermal_get_temp().
The function will look if the temperature decreased, assuming it was more than
65000, but that is not the case because the current temperature is 64656
(because of the rounding when setting the threshold). This condition being
true, we re-enable the interrupt which fires immediately after exiting the irq
thread. That happens again and again until the temperature goes to more than
65000.
Potentially, there is here an interrupt storm if the temperature stabilizes at
this temperature. A very unlikely case but possible.
In any case, it does not make sense to handle dozens of alarm interrupt for
nothing.
Fix this by rounding the threshold value to the controller resolution so the
check against the threshold is consistent with the one set in the controller.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48880b979c upstream.
The step and the base temperature are fixed values, we can simplify the
computation by converting the base temperature to milli celsius and use a
pre-computed step value. That saves us a lot of mult + div for nothing at
runtime.
Take also the opportunity to change the function names to be consistent with
the rest of the code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cb4de785c upstream.
The threaded interrupt for the alarm interrupt is requested before the
temperature controller is setup. This one can fire an interrupt immediately
leading to a kernel panic as the sensor data is not initialized.
In order to prevent that, move the threaded irq after the Tsensor is setup.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c176b10b02 upstream.
The interrupt for the temperature threshold is not enabled at the end of the
probe function, enable it after the setup is complete.
On the other side, the irq_enabled is not correctly set as we are checking if
the interrupt is masked where 'yes' means irq_enabled=false.
irq_get_irqchip_state(data->irq, IRQCHIP_STATE_MASKED,
&data->irq_enabled);
As we are always enabling the interrupt, it is pointless to check if
the interrupt is masked or not, just set irq_enabled to 'true'.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 919054fdfc upstream.
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f187851b9b ]
When failing to enter broadcast timer mode for an idle state that
requires it, a new state is selected that does not require broadcast,
but the broadcast variable remains set. This causes
tick_broadcast_exit to be called despite not having entered broadcast
mode.
This causes the WARN_ON_ONCE(!irqs_disabled()) to trigger in some
cases. It does not appear to cause problems for code today, but seems
to violate the interface so should be fixed.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74717b28cb ]
If there is any non expired timer in the queue, the RTC alarm is never set.
This is an issue when adding a timer that expires before the next non
expired timer.
Ensure the RTC alarm is set in that case.
Fixes: 2b2f5ff00f ("rtc: interface: ignore expired timers when enqueuing new timers")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f3ed79188 ]
The HDMI DDC clock found in the CCU is the parent of the actual DDC
clock within the HDMI controller. That clock is also named "hdmi-ddc".
Rename the one in the CCU to "ddc". This makes more sense than renaming
the one in the HDMI controller to something else.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 17a9180994 ]
When we process VF mailboxes, the driver is likely going to also queue
up messages to the switch manager. This process merely queues up the
FIFO, but doesn't actually begin the transmission process. Because we
hold the mailbox lock during this VF processing, the PF<->SM mailbox is
not getting processed at this time. Ensure that we actually process the
PF<->SM mailbox in between each PF<->VF mailbox.
This should ensure prompt transmission of the messages queued up after
each VF message is received and handled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 523184972b ]
With virtual PCI-Express chipsets, we now see userspace/guest drivers
trying to match the physical MPS setting to a virtual downstream port.
Of course a lone physical device surrounded by virtual interconnects
cannot make a correct decision for a proper MPS setting. Instead,
let's virtualize the MPS control register so that writes through to
hardware are disallowed. Userspace drivers like QEMU assume they can
write anything to the device and we'll filter out anything dangerous.
Since mismatched MPS can lead to AER and other faults, let's add it
to the kernel side rather than relying on userspace virtualization to
handle it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e8bcf0ae4c ]
Local Reject/Invalid RPI errors seen during discovery.
Temporary RPI cleanup was occurring regardless of SLI rev. It's only
necessary on SLI-4.
Adjust the test for whether cleanup is necessary.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 184fc2b9a8 ]
Firmware update fails with: status x17 add_status x56 on the final write
If multiple DMA buffers are used for the download, some firmware revs
have difficulty with signatures and crcs split across the dma buffer
boundaries. Resolve by making all writes be a single 4k page in length.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e256ac5b1 ]
We've had support for setting both a minimum and maximum bandwidth via
.ndo_set_vf_bw since commit 883a9ccbae ("fm10k: Add support for SR-IOV
to driver", 2014-09-20).
Likely because we do not support minimum rates, the declaration
mis-ordered the "unused" parameter, which causes warnings when analyzed
with cppcheck.
Fix this warning by properly declaring the min_rate and max_rate
variables in the declaration and definition (rather than using
"unused"). Also rename "rate" to max_rate so as to clarify that we only
support setting the maximum rate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86acc79071 ]
Previously, if an non-fatal error was reported by an endpoint, we
called report_error_detected() for the endpoint, every sibling on the
bus, and their descendents. If any of them did not implement the
.error_detected() method, do_recovery() failed, leaving all these
devices unrecovered.
For example, the system described in the bugzilla below has two devices:
0000:74:02.0 [19e5:a230] SAS controller, driver has .error_detected()
0000:74:03.0 [19e5:a235] SATA controller, driver lacks .error_detected()
When a device such as 74:02.0 reported a non-fatal error, do_recovery()
failed because 74:03.0 lacked an .error_detected() method. But per PCIe
r3.1, sec 6.2.2.2.2, such an error does not compromise the Link and
does not affect 74:03.0:
Non-fatal errors are uncorrectable errors which cause a particular
transaction to be unreliable but the Link is otherwise fully functional.
Isolating Non-fatal from Fatal errors provides Requester/Receiver logic
in a device or system management software the opportunity to recover from
the error without resetting the components on the Link and disturbing
other transactions in progress. Devices not associated with the
transaction in error are not impacted by the error.
Report non-fatal errors only to the endpoint that reported them. We really
want to check for AER_NONFATAL here, but the current code structure doesn't
allow that. Looking for pci_channel_io_normal is the best we can do now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197055
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4831ca9e4a ]
The allocation for elem may fail (especially because we're using
GFP_ATOMIC) so best to check for a null return. This fixes a potential
null pointer dereference when assigning elem->pool.
Detected by CoverityScan CID#1357507 ("Dereference null return value")
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dcfd6b839c ]
This patch is resolving Coverity hits where padding in a structure could
be used uninitialized.
- Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum()
- Initialize buffer.pad2/3 before ixgbe_hic_unlocked()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18eb86362a ]
Check memory allocation failures and return -ENOMEM in such cases, as
already done for other memory allocations in this function.
This avoids NULL pointers dereference.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: PJ Waskiewicz <peter.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 035ed07208 ]
On some i.MX6 platforms which do not have speed grading
check, opp table will not be created in platform code,
so cpufreq driver prints the following error message:
cpu cpu0: dev_pm_opp_get_opp_count: OPP table not found (-19)
However, this is not really an error in this case because the
imx6q-cpufreq driver first calls dev_pm_opp_get_opp_count()
and if it fails, it means that platform code does not provide
OPP and then dev_pm_opp_of_add_table() will be called.
In order to avoid such confusing error message, move it to
debug level.
It is up to the caller of dev_pm_opp_get_opp_count() to check its
return value and decide if it will print an error or not.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27d6162944 ]
When creating virtual functions, create the "virtfn%u" and "physfn" links
in sysfs *before* attaching the driver instead of after. When we attach
the driver to the new virtual network interface first, there is a race when
the driver attaches to the new sends out an "add" udev event, and the
network interface naming software (biosdevname or systemd, for example)
tries to look at these links.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ce9a36452 ]
Whenever an I/O for a RAID volume fails with IOCStatus
MPI2_IOCSTATUS_SCSI_IOC_TERMINATED and SCSIStatus equal to
(MPI2_SCSI_STATE_TERMINATED | MPI2_SCSI_STATE_NO_SCSI_STATUS) then
return the I/O to SCSI midlayer with "DID_RESET" (i.e. retry the IO
infinite times) set in the host byte.
Previously, the driver was completing the I/O with "DID_SOFT_ERROR"
which causes the I/O to be quickly retried. However, firmware needed
more time and hence I/Os were failing.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b3a081fb6 ]
In case of connection reset Tx skb queue can have some skbs which are
not transmitted so purge Tx skb queue in release_offload_resources() to
avoid skb leak.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 357027786f ]
When checking to see if a PCI bus can safely be reset, we previously
checked to see if any of the children had their PCI_DEV_FLAGS_NO_BUS_RESET
flag set. Children marked with that flag are known not to behave well
after a bus reset.
Some PCIe root port bridges also do not behave well after a bus reset,
sometimes causing the devices behind the bridge to become unusable.
Add a check for PCI_DEV_FLAGS_NO_BUS_RESET being set in the bridge device
to allow these bridges to be flagged, and prevent their secondary buses
from being reset.
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: fixed typo]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fc7556877d ]
Change the return error code to EINVAL if the MAC
address is not valid in the set_wol function.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5b64a2965d ]
On some platforms, the interrupt for the PL031 is optional. Avoid
trying to claim the interrupt if it's not specified.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 778f81d6cd ]
If crypto4xx is used in conjunction with dm-crypt, the available
ring buffer elements are not enough to handle the load properly.
On an aes-cbc-essiv:sha256 encrypted swap partition the read
performance is abyssal: (tested with hdparm -t)
/dev/mapper/swap_crypt:
Timing buffered disk reads: 14 MB in 3.68 seconds = 3.81 MB/sec
The patch increases both PPC4XX_NUM_SD and PPC4XX_NUM_PD to 256.
This improves the performance considerably:
/dev/mapper/swap_crypt:
Timing buffered disk reads: 104 MB in 3.03 seconds = 34.31 MB/sec
Furthermore, PPC4XX_LAST_SD, PPC4XX_LAST_GD and PPC4XX_LAST_PD
can be easily calculated from their respective PPC4XX_NUM_*
constant.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d0c49aceb ]
This fixes an overflow condition that can happen with high max
brightness and period values in compute_duty_cycle. This fixes it by
using a 64 bit variable for computing the duty cycle.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2247925f09 ]
Net device reset can fail when the h/w or f/w is in a bad state.
Subsequent netdevice open fails in bnxt_hwrm_stat_ctx_alloc().
The cleanup invokes bnxt_hwrm_resource_free() which inturn
calls bnxt_disable_int(). In this routine, the code segment
if (ring->fw_ring_id != INVALID_HW_RING_ID)
BNXT_CP_DB(cpr->cp_doorbell, cpr->cp_raw_cons);
results in NULL pointer dereference as cpr->cp_doorbell is not yet
initialized, and fw_ring_id is zero.
The fix is to initialize cpr fw_ring_id to INVALID_HW_RING_ID before
bnxt_init_chip() is invoked.
Signed-off-by: Sankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 293d264f13 ]
drv->cpumask defaults to cpu_possible_mask in __cpuidle_driver_init().
On PowerNV platform cpu_present could be less than cpu_possible in cases
where firmware detects the cpu, but it is not available to the OS. When
CONFIG_HOTPLUG_CPU=n, such cpus are not hotplugable at runtime and hence
we skip creating cpu_device.
This breaks cpuidle on powernv where register_cpu() is not called for
cpus in cpu_possible_mask that cannot be hot-added at runtime.
Trying cpuidle_register_device() on cpu without cpu_device will cause
crash like this:
cpu 0xf: Vector: 380 (Data SLB Access) at [c000000ff1503490]
pc: c00000000022c8bc: string+0x34/0x60
lr: c00000000022ed78: vsnprintf+0x284/0x42c
sp: c000000ff1503710
msr: 9000000000009033
dar: 6000000060000000
current = 0xc000000ff1480000
paca = 0xc00000000fe82d00 softe: 0 irq_happened: 0x01
pid = 1, comm = swapper/8
Linux version 4.11.0-rc2 (sv@sagarika) (gcc version 4.9.4
(Buildroot 2017.02-00004-gc28573e) ) #15 SMP Fri Mar 17 19:32:02 IST 2017
enter ? for help
[link register ] c00000000022ed78 vsnprintf+0x284/0x42c
[c000000ff1503710] c00000000022ebb8 vsnprintf+0xc4/0x42c (unreliable)
[c000000ff1503800] c00000000022ef40 vscnprintf+0x20/0x44
[c000000ff1503830] c0000000000ab61c vprintk_emit+0x94/0x2cc
[c000000ff15038a0] c0000000000acc9c vprintk_func+0x60/0x74
[c000000ff15038c0] c000000000619694 printk+0x38/0x4c
[c000000ff15038e0] c000000000224950 kobject_get+0x40/0x60
[c000000ff1503950] c00000000022507c kobject_add_internal+0x60/0x2c4
[c000000ff15039e0] c000000000225350 kobject_init_and_add+0x70/0x78
[c000000ff1503a60] c00000000053c288 cpuidle_add_sysfs+0x9c/0xe0
[c000000ff1503ae0] c00000000053aeac cpuidle_register_device+0xd4/0x12c
[c000000ff1503b30] c00000000053b108 cpuidle_register+0x98/0xcc
[c000000ff1503bc0] c00000000085eaf0 powernv_processor_idle_init+0x140/0x1e0
[c000000ff1503c60] c00000000000cd60 do_one_initcall+0xc0/0x15c
[c000000ff1503d20] c000000000833e84 kernel_init_freeable+0x1a0/0x25c
[c000000ff1503dc0] c00000000000d478 kernel_init+0x24/0x12c
[c000000ff1503e30] c00000000000b564 ret_from_kernel_thread+0x5c/0x78
This patch fixes the bug by passing correct cpumask from
powernv-cpuidle driver.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
[ rjw: Comment massage ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b07c12517f ]
Shutdown should be called for xhci_plat devices especially for
situations where kexec might be used by stopping DMA
transactions.
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c2b341a620 ]
moxart_mac_start_xmit() doesn't care where tx_tail is, tx_head can
catch and pass tx_tail, which is bad because moxart_tx_finished()
isn't guaranteed to catch up on freeing resources from tx_tail.
Add a check in moxart_mac_start_xmit() stopping the queue at the
end of the circular buffer. Also add a check in moxart_tx_finished()
waking the queue if the buffer has TX_WAKE_THRESHOLD or more
free descriptors.
While we're at it, move spin_lock_irq() to happen before our
descriptor pointer is assigned in moxart_mac_start_xmit().
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=99451
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit af109a2cf6 ]
gcc-7 points out that the AVMB1_ADDCARD ioctl results in an unintialized
value ending up in the cardnr parameter:
drivers/isdn/capi/kcapi.c: In function 'old_capi_manufacturer':
drivers/isdn/capi/kcapi.c:1042:24: error: 'cdef.cardnr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
cparams.cardnr = cdef.cardnr;
This has been broken since before the start of the git history, so
either the value is not used for anything important, or the ioctl
command doesn't get called in practice.
Setting the cardnr to zero avoids the warning and makes sure
we have consistent behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f0bb2d50df ]
The latest gcc-7.0.1 snapshot reports a new warning:
virtio/virtio_balloon.c: In function 'update_balloon_stats':
virtio/virtio_balloon.c:258:26: error: 'events[2]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:260:26: error: 'events[3]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:261:56: error: 'events[18]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:262:56: error: 'events[17]' is used uninitialized in this function [-Werror=uninitialized]
This seems absolutely right, so we should add an extra check to
prevent copying uninitialized stack data into the statistics.
>From all I can tell, this has been broken since the statistics code
was originally added in 2.6.34.
Fixes: 9564e138b1 ("virtio: Add memory statistics reporting to the balloon driver (V4)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9646b26e85 ]
The virtio balloon driver contained a not-so-obvious invariant that
update_balloon_stats has to update exactly VIRTIO_BALLOON_S_NR counters
in order to send valid stats to the host. This commit fixes it by having
update_balloon_stats return the actual number of counters, and its
callers use it when pushing buffers to the stats virtqueue.
Note that it is still out of spec to change the number of counters
at run-time. "Driver MUST supply the same subset of statistics in all
buffers submitted to the statsq."
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f0ba790df ]
The cpufreq core only tries to create symbolic links from CPU
directories in sysfs to policy directories in cpufreq_add_dev(),
either when a given CPU is registered or when the cpufreq driver
is registered, whichever happens first. That is not sufficient,
however, because cpufreq_add_dev() may be called for an offline CPU
whose policy object has not been created yet and, quite obviously,
the symbolic cannot be added in that case.
Fix that by making cpufreq_online() attempt to add symbolic links to
policy objects for the CPUs in the related_cpus mask of every new
policy object created by it.
The cpufreq_driver_lock locking around the for_each_cpu() loop
in cpufreq_online() is dropped, because it is not necessary and the
code is somewhat simpler without it. Moreover, failures to create
a symbolic link will not be regarded as hard errors any more and
the CPUs without those links will not be taken offline automatically,
but that should not be problematic in practice.
Reported-and-tested-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ac3b77a6f ]
vlsi_alloc_ring() checks for DMA mapping errors by comparing
returned address with zero, while pci_dma_mapping_error() should be used.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea174c9573 ]
When the rdma device is removed, we must cleanup all
the rdma resources within the DEVICE_REMOVAL event
handler to let the device teardown gracefully. When
this happens with live I/O, some memory regions are
occupied. Thus, track them too and dereg all the mr's.
We are safe with mr access by iscsi_iser_cleanup_task.
Reported-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13a8cd191a ]
When testing the epoll w/ busy poll code I found that I could get into a
state where the i40e driver had q_vectors w/ active NAPI that had no rings.
This was resulting in a divide by zero error. To correct it I am updating
the driver code so that we only support NAPI on q_vectors that have 1 or
more rings allocated to them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9fcd67d177 ]
According to C9-147, MSN should only be incremented when the last packet of
a multi packet request has been received.
"Logically, the requester associates a sequential Send Sequence Number
(SSN) with each WQE posted to the send queue. The SSN bears a one-
to-one relationship to the MSN returned by the responder in each re-
sponse packet. Therefore, when the requester receives a response, it in-
terprets the MSN as representing the SSN of the most recent request
completed by the responder to determine which send WQE(s) can be
completed."
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ded2602353 ]
"goto err;" has it's own kfree_skb() call so it's a double free. We
only need to free on the "goto exit;" path.
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f858685503 ]
We can't just set the timeout on the tagset, we have to set it on the
queue as it would have been setup already at this point.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb88645596 ]
When vmalloc_user is used to create memory that is supposed to be mmap'd
to user space, it is necessary for the mmap cookie (eg the offset) to be
aligned to SHMLBA.
This creates a situation where all virtual mappings of the same physical
page share the same virtual cache index and guarantees VIPT coherence.
Otherwise the cache is non-coherent and the kernel will not see writes
by userspace when reading the shared page (or vice-versa).
Reported-by: Josh Beavers <josh.beavers@gmail.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86f46aba8d ]
We need to make sure that the cq work item does not
run when we are destroying the cq. Unlike flush_work,
cancel_work_sync protects against self-requeue of the
work item (which we can do in ib_cq_poll_work).
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 871a8623d3 ]
Netdev notification events are de-registered only when all
client iwdev instances are removed. If a single client is closed
and re-opened, netdev events could arrive even before the Control
Queue-Pair (CQP) is created, causing a NULL pointer dereference crash
in i40iw_get_cqp_request. Fix this by allowing netdev event
notification only after we have reached the INET_NOTIFIER state with
respect to device initialization.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a5af839253 ]
The latest gcc-7 snapshot warns about bfa_ioc_send_enable/bfa_ioc_send_disable
writing undefined values into the hardware registers:
drivers/net/ethernet/brocade/bna/bfa_ioc.c: In function 'bfa_iocpf_sm_disabling_entry':
arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+4)' is used uninitialized in this function [-Werror=uninitialized]
arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+8)' is used uninitialized in this function [-Werror=uninitialized]
The two functions look like they should do the same thing, but only one
of them initializes the time stamp and clscode field. The fact that we
only get a warning for one of the two functions seems to be arbitrary,
based on the inlining decisions in the compiler.
To address this, I'm making both functions do the same thing:
- set the clscode from the ioc structure in both
- set the time stamp from ktime_get_real_seconds (which also
avoids the signed-integer overflow in 2038 and extends the
well-defined behavior until 2106).
- zero-fill the reserved field
Fixes: 8b230ed8ec ("bna: Brocade 10Gb Ethernet device driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit acd9776b5c ]
With AF_IUCV traffic, the skb passed to hard_start_xmit() has a 14 byte
slot at skb->data, intended for an ETH header. qeth_l3_fill_af_iucv_hdr()
fills this ETH header... and then immediately moves it to the
skb's headroom, where it disappears and is never seen again.
But it's still possible for us to return NETDEV_TX_BUSY after the skb has
been modified. Since we didn't get a private copy of the skb, the next
time the skb is delivered to hard_start_xmit() it no longer has the
expected layout (we moved the ETH header to the headroom, so skb->data
now starts at the IUCV_TRANS header). So when qeth_l3_fill_af_iucv_hdr()
does another round of rebuilding, the resulting qeth header ends up
all wrong. On transmission, the buffer is then rejected by
the HiperSockets device with SBALF15 = x'04'.
When this error is passed back to af_iucv as TX_NOTIFY_UNREACHABLE, it
tears down the offending socket.
As the ETH header for AF_IUCV serves no purpose, just align the code to
what we do for IP traffic on L3 HiperSockets: keep the ETH header at
skb->data, and pass down data_offset = ETH_HLEN to qeth_fill_buffer().
When mapping the payload into the SBAL elements, the ETH header is then
stripped off. This avoids the skb manipulations in
qeth_l3_fill_af_iucv_hdr(), and any buffer re-entering hard_start_xmit()
after NETDEV_TX_BUSY is now processed properly.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7d969d2e88 ]
Depending on the device type, hard_start_xmit() builds different output
buffer formats. For instance with HiperSockets, on both L2 and L3 we
strip the ETH header from the skb - L3 doesn't need it, and L2 carries
it in the buffer's header element.
For this, we pass data_offset = ETH_HLEN all the way down to
__qeth_fill_buffer(), where skb->data is then adjusted accordingly.
But the initial size calculation still considers the *full* skb length
(including the ETH header). So qeth_get_elements_no() can erroneously
reject a skb as too big, even though it would actually fit into an
output buffer once the ETH header has been trimmed off later.
Fix this by passing an additional offset to qeth_get_elements_no(),
that indicates where in the skb the on-wire data actually begins.
Since the current code uses data_offset=-1 for some special handling
on OSA, we need to clamp data_offset to 0...
On HiperSockets this helps when sending ~MTU-size skbs with weird page
alignment. No change for OSA or AF_IUCV.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f25abe6ba ]
The linking status may be changed when autosuspend. And, after
autoresume, the driver may try to transmit packets when the device
is carrier off, because the interrupt transfer doesn't update the
linking status, yet. And, if the device is in ALDPS mode, the device
would stop working.
The another similar case is
1. unplug the cable.
2. interrupt transfer queue a work_queue for linking change.
3. device enters the ALDPS mode.
4. a tx occurs before the work_queue is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
