Pull timer fixes from Thomas Gleixner:
"A set of small fixes plus the removal of stale board support code:
- Remove the board support code from the clpx711x clocksource driver.
This change had fallen through the cracks and I'm sending it now
rather than dealing with people who want to improve that stale code
for 3 month.
- Use the proper clocksource mask on RICSV
- Make local scope functions and variables static"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/clps711x: Remove board support
clocksource/drivers/riscv: Fix clocksource mask
clocksource/drivers/mips-gic-timer: Make gic_compare_irqaction static
clocksource/drivers/timer-ti-dm: Make omap_dm_timer_set_load_start() static
clocksource/drivers/tcb_clksrc: Make tc_clksrc_suspend/resume() static
clocksource/drivers/clps711x: Make clps711x_clksrc_init() static
time/jiffies: Make refined_jiffies static
Pull irq fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem:
- Remove secondary GIC support on systems w/o device-tree support
- A set of small fixlets in various irqchip drivers
- static and fall-through annotations
- Kernel doc and typo fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Mark expected switch case fall-through
genirq/devres: Remove excess parameter from kernel doc
irqchip/irq-mvebu-sei: Make mvebu_sei_ap806_caps static
irqchip/mbigen: Don't clear eventid when freeing an MSI
irqchip/stm32: Don't set rising configuration registers at init
irqchip/stm32: Don't clear rising/falling config registers at init
dt-bindings: irqchip: renesas-irqc: Document r8a774c0 support
irqchip/mmp: Make mmp_irq_domain_ops static
irqchip/brcmstb-l2: Make two init functions static
genirq: Fix typo in comment of IRQD_MOVE_PCNTXT
irqchip/gic-v3-its: Fix comparison logic in lpi_range_cmp
irqchip/gic: Drop support for secondary GIC in non-DT systems
irqchip/imx-irqsteer: Fix of_property_read_u32() error handling
Pull thermal management fixes from Zhang Rui:
- Fix a wrong __percpu structure declaration in intel_powerclamp driver
(Luc Van Oostenryck)
- Fix truncated name of the idle injection kthreads created by
intel_powerclamp driver (Zhang Rui)
- Fix the missing UUID supports in int3400 thermal driver (Matthew
Garrett)
- Fix a crash when accessing the debugfs of bcm2835 SoC thermal driver
(Phil Elwell)
- A couple of trivial fixes/cleanups in some SoC thermal drivers
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal/intel_powerclamp: fix truncated kthread name
thermal: mtk: Allocate enough space for mtk_thermal.
thermal/int340x_thermal: fix mode setting
thermal/int340x_thermal: Add additional UUIDs
thermal: cpu_cooling: Remove unused cur_freq variable
thermal: bcm2835: Fix crash in bcm2835_thermal_debugfs
thermal: samsung: Fix incorrect check after code merge
thermal/intel_powerclamp: fix __percpu declaration of worker_data
- Series to fix a memory leak in hd44780
while introducing charlcd_free().
From Andy Shevchenko
- Series to clean up the Kconfig menus and
a couple of improvements for charlcd.
From Mans Rullgard
-----BEGIN PGP SIGNATURE-----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=MO2/
-----END PGP SIGNATURE-----
Merge tag 'auxdisplay-for-linus-v5.1-rc2' of git://github.com/ojeda/linux
Pull auxdisplay updates from Miguel Ojeda:
"A few fixes and improvements for auxdisplay:
- Series to fix a memory leak in hd44780 while introducing
charlcd_free(). From Andy Shevchenko
- Series to clean up the Kconfig menus and a couple of improvements
for charlcd. From Mans Rullgard"
* tag 'auxdisplay-for-linus-v5.1-rc2' of git://github.com/ojeda/linux:
auxdisplay: charlcd: make backlight initial state configurable
auxdisplay: charlcd: simplify init message display
auxdisplay: deconfuse configuration
auxdisplay: hd44780: Convert to use charlcd_free()
auxdisplay: panel: Convert to use charlcd_free()
auxdisplay: charlcd: Introduce charlcd_free() helper
auxdisplay: charlcd: Move to_priv() to charlcd namespace
auxdisplay: hd44780: Fix memory leak on ->remove()
Six fixes to four drivers and two core fixes. One core fix simply
corrects a missed destroy_rcu_head() but the other is hopefully the
end of an ongoing effort to make suspend/resume play nicely with scsi
quiesce.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXJZbZCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaIGAP9dOI8E
7RJRVPzXDEq7A2YE8whsWiQw7lB/BwMIYQenIwD/YySqYO8hTIDzXzkCuR94OY5L
HTWvluKkLILX/wAFM50=
=ItVl
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes to four drivers and two core fixes.
One core fix simply corrects a missed destroy_rcu_head() but the other
is hopefully the end of an ongoing effort to make suspend/resume play
nicely with scsi quiesce"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvscsi: Fix empty event pool access during host removal
scsi: ibmvscsi: Protect ibmvscsi_head from concurrent modificaiton
scsi: hisi_sas: Add softreset in hisi_sas_I_T_nexus_reset()
scsi: qla2xxx: Fix NULL pointer crash due to stale CPUID
scsi: qla2xxx: Fix FC-AL connection target discovery
scsi: core: Avoid that a kernel warning appears during system resume
scsi: core: Also call destroy_rcu_head() for passthrough requests
scsi: iscsi: flush running unbind operations when removing a session
Since board support for the CLPS711X platform was removed,
remove the board support from the clps711x-timer driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lkml.kernel.org/r/20181220111626.17140-1-shc_work@mail.ru
-----BEGIN PGP SIGNATURE-----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=4Ktc
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190323' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A set of fixes/changes that should go into this series. This contains:
- Kernel doc / comment updates (Bart, Shenghui)
- Un-export of core-only used function (Bart)
- Fix race on loop file access (Dongli)
- pf/pcd queue cleanup fixes (me)
- Use appropriate helper for RESTART bit set (Yufen)
- Use named identifier for classic poll (Yufen)"
* tag 'for-linus-20190323' of git://git.kernel.dk/linux-block:
sbitmap: trivial - update comment for sbitmap_deferred_clear_bit
blkcg: Fix kernel-doc warnings
blk-iolatency: #include "blk.h"
block: Unexport blk_mq_add_to_requeue_list()
block: add BLK_MQ_POLL_CLASSIC for hybrid poll and return EINVAL for unexpected value
blk-mq: remove unused 'nr_expired' from blk_mq_hw_ctx
loop: access lo_backing_file only when the loop device is Lo_bound
blk-mq: use blk_mq_sched_mark_restart_hctx to set RESTART
paride/pcd: cleanup queues when detection fails
paride/pf: cleanup queues when detection fails
for stable.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAlyVCYsTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi6oFB/9Lw2OMiNrdMAgfOzcVkB4dbXbRtryG
rBsTUc/fwFrCl2N+wRmJKUkDP1e1phM9CHaGEoBYB+vL2Hhj8kjyJN4NY1g09ilt
w8XT6Pkg2Uui4kr5bnWzDS+oO8hm1ES2PbzDnIX1UiLStHypzQFwzvlm+TQE8jxb
pGNyNnbASJ+2mk+xAz7EkLGlNcAgULUT7oC/w0xj0neM739aYS3IsZgWylnw41CS
59TDyWROUUePLQnvieXmp4l58fn7xpvwrUE0KQgYec+j2t2SsKnHUoI86qZFYF2Q
NsE/K2fmIvKxWrmNw+0uuOVj+mNr2Jr5m/q+Nu61asOjs7Hz5CwUp7nd
=DkXC
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.1-rc2' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A follow up for the new alloc_size logic and a blacklisting fix,
marked for stable"
* tag 'ceph-for-5.1-rc2' of git://github.com/ceph/ceph-client:
rbd: drop wait_for_latest_osdmap()
libceph: wait for latest osdmap in ceph_monc_blacklist_add()
rbd: set io_min, io_opt and discard_granularity to alloc_size
For all riscv architectures (RV32, RV64 and RV128), the clocksource
is a 64 bit incrementing counter.
Fix the clock source mask accordingly.
Tested on both 64bit and 32 bit virt machine in QEMU.
Fixes: 62b0194368 ("clocksource: new RISC-V SBI timer driver")
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-riscv@lists.infradead.org
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Anup Patel <Anup.Patel@wdc.com>
Cc: Damien Le Moal <Damien.LeMoal@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190322215411.19362-1-atish.patra@wdc.com
Fix sparse warning:
drivers/clocksource/mips-gic-timer.c:70:18: warning:
symbol 'gic_compare_irqaction' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <daniel.lezcano@linaro.org>
Link: https://lkml.kernel.org/r/20190322144359.19516-1-yuehaibing@huawei.com
Fix sparse warning:
drivers/clocksource/timer-ti-dm.c:589:5: warning:
symbol 'omap_dm_timer_set_load_start' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <daniel.lezcano@linaro.org>
Link: https://lkml.kernel.org/r/20190322144302.6704-1-yuehaibing@huawei.com
Fix sparse warnings:
drivers/clocksource/tcb_clksrc.c:74:6: warning:
symbol 'tc_clksrc_suspend' was not declared. Should it be static?
drivers/clocksource/tcb_clksrc.c:89:6: warning:
symbol 'tc_clksrc_resume' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <nicolas.ferre@microchip.com>
Cc: <daniel.lezcano@linaro.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: https://lkml.kernel.org/r/20190322143940.12396-1-yuehaibing@huawei.com
Fix sparse warning:
drivers/clocksource/clps711x-timer.c:96:13: warning:
symbol 'clps711x_clksrc_init' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <daniel.lezcano@linaro.org>
Cc: <shc_work@mail.ru>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: https://lkml.kernel.org/r/20190322143708.12716-1-yuehaibing@huawei.com
Including:
- AMD IOMMU fix for sg-mapping with sg->offset > PAGE_SIZE
- Fix for IOVA code to trigger the slow-path less often
- Two fixes for Intel VT-d to avoid writing to read-onl registers and
to flush the right domain id for the default domains in scalable
mode
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEr9jSbILcajRFYWYyK/BELZcBGuMFAlyUxMcACgkQK/BELZcB
GuPcUBAAsRaIicKz2HFsxfkGQawrTBlDCYi3xx8MndZ44ZHWk936CEli5nhSRDmd
vCZPpl1j0HLfoUzoR4d/KEqYth+96Yh6h52e0WHh0ocIi5oJbIYZ7n8vwLT8lWQG
X7QkT6Fx8+M3mNfuF1rY4Sa2ZexgeXQeitjip3ULXyvwqg3x7oj7KkRn6IM+hRIv
BlCZXJNnjVQplWP4w/6j1BE5OtP1yDYCi3exOYO2A+2CIa7VHybOj+Ry2nEPYAAk
GvZ7kNgQwxov1626QrIp8antqswtTODUqm7x7mdCfoEqX7LPEqKKs578wkHqvIis
R8GpJxW0RI6OSSXBrRjhOhM2sgQL4csiLiMijZORGnN1jSyurY6Cdjxu24+3Gd0e
25GIYJgR5U39Uf+g/1CIBAooPoV/sUhOVmAk0HTQvnvx7kXAzdCcIpRcU1H2k0nZ
XaO/+KCuTnWbhbsdKCUmigtgs+zf1x7fkamiGp9d+rO4PlZn8UnMg6JnS0IuZVE8
gvWY5orXQx5izb3JJGLD3u21/UKq+nM8+VqN1++piCy9Vu2BPJBvabgAq7iC0Xax
CfF+5migNNfC1PMgA49LAPAyRf/CwWO1H364IyK2avAeFHCXiPSqWZ/2Urbxp2zc
u946DsMGDxo6Wamp+s2TzXbpHZ5CbSsjLNE8PhuxDjJXwVpaDOU=
=wkBN
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- AMD IOMMU fix for sg-mapping with sg->offset > PAGE_SIZE
- Fix for IOVA code to trigger the slow-path less often
- Two fixes for Intel VT-d to avoid writing to read-only registers and
to flush the right domain id for the default domains in scalable mode
* tag 'iommu-fixes-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Save the right domain ID used by hardware
iommu/vt-d: Check capability before disabling protected memory
iommu/iova: Fix tracking of recently failed iova address
iommu/amd: fix sg->dma_address for sg->offset bigger than PAGE_SIZE
Prevent device references acquired by bus_find_device() in
acpi_dev_present() from being leaked (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=h/7V
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Prevent device references acquired by bus_find_device() in
acpi_dev_present() from being leaked (Andy Shevchenko)"
* tag 'acpi-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / utils: Drop reference in test for device presence
- Rearrange the generic power domains (genpd) code to avoid a
potential deadlock possible due to its interactions with the
clock framework (Jiada Wang).
- Make turbostat return the exit status of the command run
under it if that command fails (David Arcari).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=RgAd
-----END PGP SIGNATURE-----
Merge tag 'pm-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These rearrange some code in the generic power domains (genpd)
framework to avoid a potential deadlock and make the turbostat utility
behave more as expected.
Specifics:
- Rearrange the generic power domains (genpd) code to avoid a
potential deadlock possible due to its interactions with the clock
framework (Jiada Wang)
- Make turbostat return the exit status of the command run under it
if that command fails (David Arcari)"
* tag 'pm-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Avoid a potential deadlock
tools/power turbostat: return the exit status of a command
The driver sets a default domain id (FLPT_DEFAULT_DID) in the
first level only pasid entry, but saves a different domain id
in @sdev->did. The value saved in @sdev->did will be used to
invalidate the translation caches. Hence, the driver might
result in invalidating the caches with a wrong domain id.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Fixes: 1c4f88b7f1 ("iommu/vt-d: Shared virtual address in scalable mode")
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The spec states in 10.4.16 that the Protected Memory Enable
Register should be treated as read-only for implementations
not supporting protected memory regions (PLMR and PHMR fields
reported as Clear in the Capability register).
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: mark gross <mgross@intel.com>
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Fixes: f8bab73515 ("intel-iommu: PMEN support")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
If a 32 bit allocation request is too big to possibly succeed, it
early exits with a failure and then should never update max32_alloc_
size. This patch fixes current code, now the size is only updated if
the slow path failed while walking the tree. Without the fix the
allocation may enter the slow path again even if there was a failure
before of a request with the same or a smaller size.
Cc: <stable@vger.kernel.org> # 4.20+
Fixes: bee60e94a1 ("iommu/iova: Optimise attempts to allocate iova from 32bit address range")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJclEWjAAoJEAx081l5xIa+5g8QAJmtCZU/sNqyatqVy3tJNSmM
gXmrHDl/rM44TI1QDc82TP8v2GFxs66/LskjO687EhN2O2cVBtahbDwZrGq4OyvS
DLLC/T1suMgLLhw5RWtVkEe+2Xv/AaIsQ1nr2qkR9JWk8/ye9tgNgBfNeFfhCa+3
Pc5WIrVr7iJshJKuFJU7T5IBUwxGfhPRlBjZ2Lvu/VpZaH2TL4sD6KB1P86jTg2x
zcQpX8HCLQtBBc2BVGGj5J/7ZU92WVdDkQYAYUlagoEL6KKj3GINbONGE+D1Rndy
RmhZ44I6EQSzSZPOQKMPGUr7v8j7j4FrBNQXfgA958ihGyAewtTv4y+BxlHU+hnM
70t8w8PDRwHNDiPuTK2/H683l45V3yINat4evu3JI76Jk0lichDDICsU/opYjx6r
vhC+AksmypYGd9ddjm/EWB5XW8z4gBO3L5mnhCR3qKUhzEozFpR+3MVktdY7fPbd
YbUl4GM/1mvstMvQNWu224yILMdvaZa3aiHLUND/oViFP1AsVVAYroHPYY+E65tY
Zlw9JELiUBgeGJxbYtMovn2n0aAnDGjTKtZAxy7pkz8QI059MVvdhaAQTSEViBTR
UmMgTUWTb6fWwZ6a6FpzC/c9a/zaQMIWPYNUnu/TCPkDpGP7m6H0tv6U7aP4IOUP
dIp1fQKqxx1BVpfx+Hpi
=yoB3
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2019-03-22' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"i915, amdgpu, vmwgfx, exynos, nouveau and udl fixes.
Seems to be lots of little minor ones for regressions in rc1, and some
cleanups. The exynos one is the largest one, and is for a hw
difference between exynos versions"
* tag 'drm-fixes-2019-03-22' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/dmem: empty chunk do not have a buffer object associated with them.
drm/nouveau/debugfs: Fix check of pm_runtime_get_sync failure
drm/nouveau/dmem: Fix a NULL vs IS_ERR() check
drm/nouveau/dmem: remove set but not used variable 'drm'
drm/exynos/mixer: fix MIXER shadow registry synchronisation code
drm/vmwgfx: Don't double-free the mode stored in par->set_mode
drm/vmwgfx: Return 0 when gmrid::get_node runs out of ID's
drm/amdgpu: fix invalid use of change_bit
drm/amdgpu: revert "cleanup setting bulk_movable"
drm/i915: Sanity check mmap length against object size
drm/i915: Fix off-by-one in reporting hanging process
drm/i915/bios: assume eDP is present on port A when there is no VBT
drm/udl: use drm_gem_object_put_unlocked.
plus a fix off-by-one in our hang report and a protection;
and a fix for eDP panels on Gen9 platforms on VBT absence.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJckpgDAAoJEPpiX2QO6xPKDDgH/i9AQQLbJCX/nXzJUhnKSvu5
xFIFbXt/kd5hkeRVZ/qLW831okdJdVq8GW/C4AAfEMNbnhhhAI1/PRuO7lrHKuU6
QAOKvJrNKkdRxNrkHArIKXTdfjr4UnXOgQFSgFQNRLFmOi9/czoeWG0/kGkvp+WT
6HV7o1Zgghqs9SUOtmA9TZ/znq1neLlwJRuePep1TY4vbJoWnZ0ekn/MqUPDWpg2
W5stfS7AyuMX1CWJnr91G6NEqaU8Bm9aC1WmBqvdPPkVYWIJNDGWLjOEDpqzdoi4
D17RntvZ685mer+GM6fMICY09lC9vuYomT3gdRy4ZLz24VmMSyZJ7juJoYYGa7Y=
=gHfL
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-fixes-2019-03-20' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
A protection on our mmap against attempts to map past the end of the object;
plus a fix off-by-one in our hang report and a protection;
and a fix for eDP panels on Gen9 platforms on VBT absence.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190320201451.GA7993@intel.com
Empty chunk do not have a bo associated with them so no need to pin/unpin
on suspend/resume.
This fix suspend/resume on 5.1rc1 when NOUVEAU_SVM is enabled.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Tested-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
pm_runtime_get_sync returns negative on failure.
Fixes: eaeb9010bb ("drm/nouveau/debugfs: Wake up GPU before doing any reclocking")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The hmm_devmem_add() function doesn't return NULL, it returns error
pointers.
Fixes: 5be73b6908 ("drm/nouveau/dmem: device memory helpers for SVM")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/nouveau/nouveau_dmem.c: In function 'nouveau_dmem_free':
drivers/gpu/drm/nouveau/nouveau_dmem.c:103:22: warning:
variable 'drm' set but not used [-Wunused-but-set-variable]
struct nouveau_drm *drm;
^
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fix sparse warning:
drivers/irqchip/irq-mvebu-sei.c:481:23: warning:
symbol 'mvebu_sei_ap806_caps' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <jason@lakedaemon.net>
Cc: <andrew@lunn.ch>
Cc: <gregory.clement@bootlin.com>
Cc: <sebastian.hesselbarth@gmail.com>
Cc: <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: https://lkml.kernel.org/r/20190321151448.15600-1-yuehaibing@huawei.com
mbigen_write_msg clears eventid bits of a mbigen register
when free a interrupt, because msi_domain_deactivate memset
struct msg to zero. Then multiple mbigen pins with zero eventid
will report the same interrupt number.
The eventid clear call trace:
free_irq
__free_irq
irq_shutdown
irq_domain_deactivate_irq
__irq_domain_deactivate_irq
__irq_domain_deactivate_irq
msi_domain_deactivate
platform_msi_write_msg
mbigen_write_msg
Signed-off-by: Jianguo Chen <chenjianguo3@huawei.com>
[maz: massaged subject]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The rising configuration status register (rtsr) is not banked.
As it is shared with the co-processor, it should not be written at probe
time, else the co-processor configuration will be lost.
Fixes: f9fc174550 ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Falling and rising configuration and status registers are not banked.
As they are shared with M4 co-processor, they should not be cleared
at probe time, else M4 co-processor configuration will be lost.
Fixes: f9fc174550 ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Fix sparse warning:
drivers/irqchip/irq-mmp.c:182:29: warning:
symbol 'mmp_irq_domain_ops' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Fix sparse warnings:
drivers/irqchip/irq-brcmstb-l2.c:278:12: warning:
symbol 'brcmstb_l2_edge_intc_of_init' was not declared. Should it be static?
drivers/irqchip/irq-brcmstb-l2.c:285:12: warning:
symbol 'brcmstb_l2_lvl_intc_of_init' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
R-Car Gen2 has two different SDHI incarnations in the same chip. The
older one does not support the recently introduced 32 bit register
access to the block count register. Make sure we use this feature only
after the first known version.
Thanks to the Renesas Testing team for this bug report!
Fixes: 5603731a15 ("mmc: tmio: fix access width of Block Count Register")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Phong Hoang <phong.hoang.wz@renesas.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting max_blk_count to 1 here was causing the mmc block layer
to always use the MMC_READ_SINGLE_BLOCK command here, which the
driver does not DMA-accelerate.
Drop the max_blk_ settings here. The mmc host defaults suffice,
along with the max_segs and max_seg_size settings, which I have
now documented in more detail.
Now each MMC command reads 4 512-byte blocks, using DMA instead of
PIO. On my SD card, this increases read performance (measured with dd)
from 167kb/sec to 4.6mb/sec.
Link: http://lkml.kernel.org/r/CAD8Lp47L5T3jnAjBiPs1cQ+yFA3L6LJtgFvMETnBrY63-Zdi2g@mail.gmail.com
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Fixes: c5413ad815 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 6d5cd068ee ("mmc: sdhci: use WP GPIO in
sdhci_check_ro()") and commit 39ee32ce48 ("mmc: sdhci-omap: drop
->get_ro() implementation"), sdhci-omap relied on SDHCI_PRESENT_STATE
to check if the card is read-only, if wp-gpios is not populated
in device tree. However SDHCI_PRESENT_STATE in sdhci-omap does not have
correct read-only state.
sdhci-omap can be used by platforms with both micro SD slot and standard
SD slot with physical write protect pin (using GPIO). Set caps2 to
MMC_CAP2_NO_WRITE_PROTECT based on if wp-gpios property is populated or
not.
This fix is required since existing device-tree node doesn't have
"disable-wp" property and to preserve old-dt compatibility.
Fixes: 6d5cd068ee ("mmc: sdhci: use WP GPIO in sdhci_check_ro()")
Fixes: 39ee32ce48 ("mmc: sdhci-omap: drop ->get_ro() implementation")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MIXER on Exynos5 SoCs uses different synchronisation method than Exynos4
to update internal state (shadow registers).
Apparently the driver implements it incorrectly. The rule should be
as follows:
- do not request updating registers until previous request was finished,
ie. MXR_CFG_LAYER_UPDATE_COUNT must be 0.
- before setting registers synchronisation on VSYNC should be turned off,
ie. MXR_STATUS_SYNC_ENABLE should be reset,
- after finishing MXR_STATUS_SYNC_ENABLE should be set again.
The patch hopefully implements it correctly.
Below sample kernel log from page fault caused by the bug:
[ 25.670038] exynos-sysmmu 14650000.sysmmu: 14450000.mixer: PAGE FAULT occurred at 0x2247b800
[ 25.677888] ------------[ cut here ]------------
[ 25.682164] kernel BUG at ../drivers/iommu/exynos-iommu.c:450!
[ 25.687971] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 25.693778] Modules linked in:
[ 25.696816] CPU: 5 PID: 1553 Comm: fb-release_test Not tainted 5.0.0-rc7-01157-g5f86b1566bdd #136
[ 25.705646] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 25.711710] PC is at exynos_sysmmu_irq+0x1c0/0x264
[ 25.716470] LR is at lock_is_held_type+0x44/0x64
v2: added missing MXR_CFG_LAYER_UPDATE bit setting in mixer_enable_sync
Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The event pool used for queueing commands is destroyed fairly early in the
ibmvscsi_remove() code path. Since, this happens prior to the call so
scsi_remove_host() it is possible for further calls to queuecommand to be
processed which manifest as a panic due to a NULL pointer dereference as
seen here:
PANIC: "Unable to handle kernel paging request for data at address
0x00000000"
Context process backtrace:
DSISR: 0000000042000000 ????Syscall Result: 0000000000000000
4 [c000000002cb3820] memcpy_power7 at c000000000064204
[Link Register] [c000000002cb3820] ibmvscsi_send_srp_event at d000000003ed14a4
5 [c000000002cb3920] ibmvscsi_send_srp_event at d000000003ed14a4 [ibmvscsi] ?(unreliable)
6 [c000000002cb39c0] ibmvscsi_queuecommand at d000000003ed2388 [ibmvscsi]
7 [c000000002cb3a70] scsi_dispatch_cmd at d00000000395c2d8 [scsi_mod]
8 [c000000002cb3af0] scsi_request_fn at d00000000395ef88 [scsi_mod]
9 [c000000002cb3be0] __blk_run_queue at c000000000429860
10 [c000000002cb3c10] blk_delay_work at c00000000042a0ec
11 [c000000002cb3c40] process_one_work at c0000000000dac30
12 [c000000002cb3cd0] worker_thread at c0000000000db110
13 [c000000002cb3d80] kthread at c0000000000e3378
14 [c000000002cb3e30] ret_from_kernel_thread at c00000000000982c
The kernel buffer log is overfilled with this log:
[11261.952732] ibmvscsi: found no event struct in pool!
This patch reorders the operations during host teardown. Start by calling
the SRP transport and Scsi_Host remove functions to flush any outstanding
work and set the host offline. LLDD teardown follows including destruction
of the event pool, freeing the Command Response Queue (CRQ), and unmapping
any persistent buffers. The event pool destruction is protected by the
scsi_host lock, and the pool is purged prior of any requests for which we
never received a response. Finally, move the removal of the scsi host from
our global list to the end so that the host is easily locatable for
debugging purposes during teardown.
Cc: <stable@vger.kernel.org> # v2.6.12+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For each ibmvscsi host created during a probe or destroyed during a remove
we either add or remove that host to/from the global ibmvscsi_head
list. This runs the risk of concurrent modification.
This patch adds a simple spinlock around the list modification calls to
prevent concurrent updates as is done similarly in the ibmvfc driver and
ipr driver.
Fixes: 32d6e4b6e4 ("scsi: ibmvscsi: add vscsi hosts to global list_head")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We found out that for v2 hw, a SATA disk can not be written to after the
system comes up.
In commit ffb1c820b8 ("scsi: hisi_sas: remove the check of sas_dev status
in hisi_sas_I_T_nexus_reset()"), we introduced a path where we may issue an
internal abort for a SATA device, but without following it with a
softreset.
We need to always follow an internal abort with a software reset, as per HW
programming flow, so add this.
Fixes: ffb1c820b8 ("scsi: hisi_sas: remove the check of sas_dev status in hisi_sas_I_T_nexus_reset()")
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpi_range_list is supposed to be sorted in ascending order of
->base_id (at least if the range merging is to work), but the current
comparison function returns a positive value if rb->base_id >
ra->base_id, which means that list_sort() will put A after B in that
case - and vice versa, of course.
Fixes: 880cb3cddd (irqchip/gic-v3-its: Refactor LPI allocator)
Cc: stable@vger.kernel.org (v4.19+)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When calling vmw_fb_set_par(), the mode stored in par->set_mode gets free'd
twice. The first free is in vmw_fb_kms_detach(), the second is near the
end of vmw_fb_set_par() under the name of 'old_mode'. The mode-setting code
only works correctly if the mode doesn't actually change. Removing
'old_mode' in favor of using par->set_mode directly fixes the problem.
Cc: <stable@vger.kernel.org>
Fixes: a278724aa2 ("drm/vmwgfx: Implement fbdev on kms v2")
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
If it's not a system error and get_node implementation accommodate the
buffer object then it should return 0 with memm::mm_node set to NULL.
v2: Test for id != -ENOMEM instead of id == -ENOSPC.
Cc: <stable@vger.kernel.org>
Fixes: 4eb085e42f ("drm/vmwgfx: Convert to new IDA API")
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
