commit 42b32b164a upstream.
According to programming guide in host mode, port
power must be turned on in session request
interrupt handlers.
Fixes: 21795c826a ("usb: dwc2: exit hibernation on session request")
Cc: <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094550.75484A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f88359e158 upstream.
From: John Stultz <john.stultz@linaro.org>
According to the programming guide, to switch mode for DRD controller,
the driver needs to do the following.
To switch from device to host:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(host mode)
3. Reset the host with USBCMD.HCRESET
4. Then follow up with the initializing host registers sequence
To switch from host to device:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(device mode)
3. Reset the device with DCTL.CSftRst
4. Then follow up with the initializing registers sequence
Currently we're missing step 1) to do GCTL.CoreSoftReset and step 3) of
switching from host to device. John Stult reported a lockup issue seen
with HiKey960 platform without these steps[1]. Similar issue is observed
with Ferry's testing platform[2].
So, apply the required steps along with some fixes to Yu Chen's and John
Stultz's version. The main fixes to their versions are the missing wait
for clocks synchronization before clearing GCTL.CoreSoftReset and only
apply DCTL.CSftRst when switching from host to device.
[1] https://lore.kernel.org/linux-usb/20210108015115.27920-1-john.stultz@linaro.org/
[2] https://lore.kernel.org/linux-usb/0ba7a6ba-e6a7-9cd4-0695-64fc927e01f1@gmail.com/
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Ferry Toth <fntoth@gmail.com>
Cc: Wesley Cheng <wcheng@codeaurora.org>
Cc: <stable@vger.kernel.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Wesley Cheng <wcheng@codeaurora.org>
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/374440f8dcd4f06c02c2caf4b1efde86774e02d9.1618521663.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c560e76319 upstream.
The START_TRANSFER command needs to be executed while in ON/U0 link
state (with an exception during register initialization). Don't use
dwc->link_state to check this since the driver only tracks the link
state when the link state change interrupt is enabled. Check the link
state from DSTS register instead.
Note that often the host already brings the device out of low power
before it sends/requests the next transfer. So, the user won't see any
issue when the device starts transfer then. This issue is more
noticeable in cases when the device delays starting transfer, which can
happen during delayed control status after the host put the device in
low power.
Fixes: 799e9dc829 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/bcefaa9ecbc3e1936858c0baa14de6612960e909.1618884221.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3232a3ce55 upstream.
The programming guide incorrectly stated that the DCFG.bInterval_m1 must
be set to 0 when operating in fullspeed. There's no such limitation for
all IPs. See DWC_usb3x programming guide section 3.2.2.1.
Fixes: a1679af85b ("usb: dwc3: gadget: Fix setting of DEPCFG.bInterval_m1")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5d4139ae89d810eb0a2d8577fb096fc88e87bfab.1618472454.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55b74ce7d2 upstream.
Fixes bug with the handling of more than one language in
the string table in f_fs.c.
str_count was not reset for subsequent language codes.
str_count-- "rolls under" and processes u32 max strings on
the processing of the second language entry.
The existing bug can be reproduced by adding a second language table
to the structure "strings" in tools/usb/ffs-test.c.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Link: https://lore.kernel.org/r/20210317224109.21534-1-dean@sensoray.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43c4cab006 upstream.
Upon driver unbind usb_free_all_descriptors() function frees all
speed descriptor pointers without setting them to NULL. In case
gadget speed changes (i.e from super speed plus to super speed)
after driver unbind only upto super speed descriptor pointers get
populated. Super speed plus desc still holds the stale (already
freed) pointer. Fix this issue by setting all descriptor pointers
to NULL after freeing them in usb_free_all_descriptors().
Fixes: f5c61225cf ("usb: gadget: Update function for SuperSpeedPlus")
cc: stable@vger.kernel.org
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1619034452-17334-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a5d797a9f upstream.
Fix a general protection fault reported by syzbot due to a race between
gadget_setup() and gadget_unbind() in raw_gadget.
The gadget core is supposed to guarantee that there won't be any more
callbacks to the gadget driver once the driver's unbind routine is
called. That guarantee is enforced in usb_gadget_remove_driver as
follows:
usb_gadget_disconnect(udc->gadget);
if (udc->gadget->irq)
synchronize_irq(udc->gadget->irq);
udc->driver->unbind(udc->gadget);
usb_gadget_udc_stop(udc);
usb_gadget_disconnect turns off the pullup resistor, telling the host
that the gadget is no longer connected and preventing the transmission
of any more USB packets. Any packets that have already been received
are sure to processed by the UDC driver's interrupt handler by the time
synchronize_irq returns.
But this doesn't work with dummy_hcd, because dummy_hcd doesn't use
interrupts; it uses a timer instead. It does have code to emulate the
effect of synchronize_irq, but that code doesn't get invoked at the
right time -- it currently runs in usb_gadget_udc_stop, after the unbind
callback instead of before. Indeed, there's no way for
usb_gadget_remove_driver to invoke this code before the unbind callback.
To fix this, move the synchronize_irq() emulation code to dummy_pullup
so that it runs before unbind. Also, add a comment explaining why it is
necessary to have it there.
Reported-by: syzbot+eb4674092e6cc8d9e0bd@syzkaller.appspotmail.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210419033713.3021-1-mail@anirudhrb.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 475e8be53d ]
If the device doesn't support LPM, make sure to disable the LPM
capability and don't advertise to the host that it supports it.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9e68527ff932b1646f92a7593d4092a903754666.1618366071.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 025f97d188 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408130831.56239-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9535b99533 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408091836.55227-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a932ee40c2 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092947.3271507-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 286fd02fd5 ]
The Max Interrupters supported by the controller is given in a 10bit
wide bitfield, but the driver uses a fixed 128 size array to index these
interrupters.
Klockwork reports a possible array out of bounds case which in theory
is possible. In practice this hasn't been hit as a common number of Max
Interrupters for new controllers is 8, not even close to 128.
This needs to be fixed anyway
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210406070208.3406266-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bee1f89aad ]
The xHCI driver support usb2 HW LPM by default, here add support
XHCI_HW_LPM_DISABLE quirk, then we can disable usb2 lpm when
need it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1617181553-3503-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64364bc912 ]
Some hosts incorrectly use sub-minor version for minor version (i.e.
0x02 instead of 0x20 for bcdUSB 0x320 and 0x01 for bcdUSB 0x310).
Currently the xHCI driver works around this by just checking for minor
revision > 0x01 for USB 3.1 everywhere. With the addition of USB 3.2,
checking this gets a bit cumbersome. Since there is no USB release with
bcdUSB 0x301 to 0x309, we can assume that sub-minor version 01 to 09 is
incorrect. Let's try to fix this and use the minor revision that matches
with the USB/xHCI spec to help with the version checking within the
driver.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ed330e95a19dc367819c5b4d78bf7a541c35aa0a.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71ca43f30d ]
The current dwc3_gadget_reset_interrupt() will stop any active
transfers, but only addresses blocking of EP queuing for while we are
coming from a disconnected scenario, i.e. after receiving the disconnect
event. If the host decides to issue a bus reset on the device, the
connected parameter will still be set to true, allowing for EP queuing
to continue while we are disabling the functions. To avoid this, set the
connected flag to false until the stop active transfers is complete.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616146285-19149-3-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a59c68a6a3 ]
Currently user can configure UAC1 function with
parameters that violate UAC1 spec or are not supported
by UAC1 gadget implementation.
This can lead to incorrect behavior if such gadget
is connected to the host - like enumeration failure
or other issues depending on host's UAC1 driver
implementation, bringing user to a long hours
of debugging the issue.
Instead of silently accept these parameters, throw
an error if they are not valid.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-5-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3713d5ceb0 ]
Currently user can configure UAC2 function with
parameters that violate UAC2 spec or are not supported
by UAC2 gadget implementation.
This can lead to incorrect behavior if such gadget
is connected to the host - like enumeration failure
or other issues depending on host's UAC2 driver
implementation, bringing user to a long hours
of debugging the issue.
Instead of silently accept these parameters, throw
an error if they are not valid.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-4-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a154ec9ef ]
According with USB Device Class Definition for Video Device the
Processing Unit Descriptor bLength should be 12 (10 + bmControlSize),
but it has 11.
Invalid length caused that Processing Unit Descriptor Test Video form
CV tool failed. To fix this issue patch adds bmVideoStandards into
uvc_processing_unit_descriptor structure.
The bmVideoStandards field was added in UVC 1.1 and it wasn't part of
UVC 1.0a.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20210315071748.29706-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26adde04ac ]
Patch adds extra checking for bInterval passed by configfs.
The 5.6.4 chapter of USB Specification (rev. 2.0) say:
"A high-bandwidth endpoint must specify a period of 1x125 µs
(i.e., a bInterval value of 1)."
The issue was observed during testing UVC class on CV.
I treat this change as improvement because we can control
bInterval by configfs.
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210308125338.4824-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ca91fd8c76 upstream.
Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work
after the system resumes from suspend with remote wakeup enabled
device connected:
[ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71)
[ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71)
Information of this hub:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=5487 Rev= 1.47
S: Manufacturer=Dell Inc.
S: Product=Dell dock
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
The failure results from the ETIMEDOUT by chance when turning on
the suspend feature for the specified port of the hub. The port
seems to be in an unknown state so the hub_activate during resume
fails the hub_port_status, then the hub will fail to work.
The quirky hub needs the reset-resume quirk to function correctly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210420174651.6202-1-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8b3b51961 upstream.
suspend() does its poisoning conditionally, resume() does it
unconditionally. On a device with combined interfaces this
will balance, on a device with two interfaces the counter will
go negative and resubmission will fail.
Both actions need to be done conditionally.
Fixes: 6069e3e927 ("USB: cdc-acm: untangle a circular dependency between callback and softint")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210421074513.4327-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e9c93af72 upstream.
Fuzzing uncovered race condition between sysfs code paths in usbip
drivers. Device connect/disconnect code paths initiated through
sysfs interface are prone to races if disconnect happens during
connect and vice versa.
This problem is common to all drivers while it can be reproduced easily
in vhci_hcd. Add a sysfs_lock to usbip_device struct to protect the paths.
Use this in vhci_hcd to protect sysfs paths. For a complete fix, usip_host
and usip-vudc drivers and the event handler will have to use this lock to
protect the paths. These changes will be done in subsequent patches.
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+a93fba6d384346a761e3@syzkaller.appspotmail.com
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/b6568f7beae702bbc236a545d3c020106ca75eac.1616807117.git.skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5aef629704 upstream.
Ensure that dep->flags are cleared until after stop active transfers
is completed. Otherwise, the ENDXFER command will not be executed
during ep disable.
Fixes: f09ddcfcb8 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616610664-16495-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e4010e36a upstream.
The ACPI probe starts failing since commit bea46b9815 ("usb: dwc3:
qcom: Add interconnect support in dwc3 driver"), because there is no
interconnect support for ACPI, and of_icc_get() call in
dwc3_qcom_interconnect_init() will just return -EINVAL.
Fix the problem by skipping interconnect init for ACPI probe, and then
the NULL icc_path_ddr will simply just scheild all ICC calls.
Fixes: bea46b9815 ("usb: dwc3: qcom: Add interconnect support in dwc3 driver")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210311060318.25418-1-shawn.guo@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93f672804b upstream.
In host mode port connection status flag is "0" when loading
the driver. After loading the driver system asserts suspend
which is handled by "_dwc2_hcd_suspend()" function. Before
the system suspend the port connection status is "0". As
result need to check the "port_connect_status" if it is "0",
then skipping entering to suspend.
Cc: <stable@vger.kernel.org> # 5.2
Fixes: 6f6d70597c ("usb: dwc2: bus suspend/resume for hosts with DWC2_POWER_DOWN_PARAM_NONE")
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210326102510.BDEDEA005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e3bbae8ee upstream.
Increased the waiting timeout for HPRT0.PrtSusp register field
to be set, because on HiKey 960 board HPRT0.PrtSusp wasn't
generated with the existing timeout.
Cc: <stable@vger.kernel.org> # 4.18
Fixes: 22bb5cfdf1 ("usb: dwc2: Fix host exit from hibernation flow.")
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210326102447.8F7FEA005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72035f4954 upstream.
init_dma_pools() calls dma_pool_create(...dev->dev) to create dma pool.
however, dev->dev is actually set after calling init_dma_pools(), which
effectively makes dma_pool_create(..NULL) and cause crash.
To fix this issue, init dma only after dev->dev is set.
[ 1.317993] RIP: 0010:dma_pool_create+0x83/0x290
[ 1.323257] Call Trace:
[ 1.323390] ? pci_write_config_word+0x27/0x30
[ 1.323626] init_dma_pools+0x41/0x1a0 [snps_udc_core]
[ 1.323899] udc_pci_probe+0x202/0x2b1 [amd5536udc_pci]
Fixes: 7c51247a1f (usb: gadget: udc: Provide correct arguments for 'dma_pool_create')
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210317230400.357756-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e49bf376c upstream.
If tty-device registration fails the driver would fail to release the
data interface. When the device is later disconnected, the disconnect
callback would still be called for the data interface and would go about
releasing already freed resources.
Fixes: c93d819550 ("usb: cdc-acm: fix error handling in acm_probe()")
Cc: stable@vger.kernel.org # 3.9
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7180495cb3 upstream.
If tty-device registration fails the driver copy of any Country
Selection functional descriptor would end up being freed twice; first
explicitly in the error path and then again in the tty-port destructor.
Drop the first erroneous free that was left when fixing a tty-port
resource leak.
Fixes: cae2bc768d ("usb: cdc-acm: Decrement tty port's refcount if probe() fail")
Cc: stable@vger.kernel.org # 4.19
Cc: Jaejoong Kim <climbbb.kim@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4c77070ad upstream.
This failure is so common that logging an error here amounts
to spamming log files.
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210311130126.15972-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08dff274ed upstream.
Counting break events is nice but we should actually report them to
the tty layer.
Fixes: 5a6a62bdb9 ("cdc-acm: add TIOCMIWAIT")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20210311133714.31881-1-oneukum@suse.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f978a30c9 upstream.
The MediaTek 0.96 xHCI controller on some platforms does not
support bulk stream even HCCPARAMS says supporting, due to MaxPSASize
is set a default value 1 by mistake, here use XHCI_BROKEN_STREAMS
quirk to fix it.
Fixes: 94a631d91a ("usb: xhci-mtk: check hcc_params after adding primary hcd")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92af4fc6ec upstream.
Pinephone running on Allwinner A64 fails to suspend with USB devices
connected as reported by Bhushan Shah <bshah@kde.org>. Reverting
commit 5fbf7a2534 ("usb: musb: fix idling for suspend after
disconnect interrupt") fixes the issue.
Let's add suspend checks also for suspend after disconnect interrupt
quirk handling like we already do elsewhere.
Fixes: 5fbf7a2534 ("usb: musb: fix idling for suspend after disconnect interrupt")
Reported-by: Bhushan Shah <bshah@kde.org>
Tested-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210324071142.42264-1-tony@atomide.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bd860493f upstream.
This LTE modem (M.2 card) has a bug in its power management:
there is some kind of race condition for U3 wake-up between the host and
the device. The modem firmware sometimes crashes/locks when both events
happen at the same time and the modem fully drops off the USB bus (and
sometimes re-enumerates, sometimes just gets stuck until the next
reboot).
Tested with the modem wired to the XHCI controller on an AMD 3015Ce
platform. Without the patch, the modem dropped of the USB bus 5 times in
3 days. With the quirk, it stayed connected for a week while the
'runtime_suspended_time' counter incremented as excepted.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210319124802.2315195-1-vpalatin@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b522f830d3 ]
It seems that on Intel Merrifield platform the USB PHY shouldn't be suspended.
Otherwise it can't be enabled by simply change the cable in the connector.
Enable corresponding quirk for the platform in question.
Fixes: e5f4ca3fce ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression")
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210322125244.79407-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f09ddcfcb8 upstream.
In the situations where the DWC3 gadget stops active transfers, once
calling the dwc3_gadget_giveback(), there is a chance where a function
driver can queue a new USB request in between the time where the dwc3
lock has been released and re-aquired. This occurs after we've already
issued an ENDXFER command. When the stop active transfers continues
to remove USB requests from all dep lists, the newly added request will
also be removed, while controller still has an active TRB for it.
This can lead to the controller accessing an unmapped memory address.
Fix this by ensuring parameters to prevent EP queuing are set before
calling the stop active transfers API.
Fixes: ae7e86108b ("usb: dwc3: Stop active transfers before halting the controller")
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1615507142-23097-1-git-send-email-wcheng@codeaurora.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77adb8bdf4 upstream.
The DWC3 runtime suspend routine checks for the USB connected parameter to
determine if the controller can enter into a low power state. The
connected state is only set to false after receiving a disconnect event.
However, in the case of a device initiated disconnect (i.e. UDC unbind),
the controller is halted and a disconnect event is never generated. Set
the connected flag to false if issuing a device initiated disconnect to
allow the controller to be suspended.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609283136-22140-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86629e098a upstream.
tcpm-source-psy- does not invoke power_supply_changed API when
one of the published power supply properties is changed.
power_supply_changed needs to be called to notify
userspace clients(uevents) and kernel clients.
Fixes: f2a8aa053c ("typec: tcpm: Represent source supply through power_supply")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210317181249.1062995-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cac9104be upstream.
Remove the unused "u32 vdo[3]" part in the tps6598x_rx_identity_reg
struct. This helps avoid "failed to register partner" errors which
happen when tps6598x_read_partner_identity() fails because the
amount of data read is 12 bytes smaller than the struct size.
Note that vdo[3] is already in usb_pd_identity and hence
shouldn't be added to tps6598x_rx_identity_reg as well.
Fixes: f6c56ca91b ("usb: typec: Add the Product Type VDOs to struct usb_pd_identity")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Elias Rudberg <mail@eliasrudberg.se>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210311124710.6563-1-mail@eliasrudberg.se
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98f153a10d upstream.
When gadget is disconnected, running sequence is like this.
. composite_disconnect
. Call trace:
usb_string_copy+0xd0/0x128
gadget_config_name_configuration_store+0x4
gadget_config_name_attr_store+0x40/0x50
configfs_write_file+0x198/0x1f4
vfs_write+0x100/0x220
SyS_write+0x58/0xa8
. configfs_composite_unbind
. configfs_composite_bind
In configfs_composite_bind, it has
"cn->strings.s = cn->configuration;"
When usb_string_copy is invoked. it would
allocate memory, copy input string, release previous pointed memory space,
and use new allocated memory.
When gadget is connected, host sends down request to get information.
Call trace:
usb_gadget_get_string+0xec/0x168
lookup_string+0x64/0x98
composite_setup+0xa34/0x1ee8
If gadget is disconnected and connected quickly, in the failed case,
cn->configuration memory has been released by usb_string_copy kfree but
configfs_composite_bind hasn't been run in time to assign new allocated
"cn->configuration" pointer to "cn->strings.s".
When "strlen(s->s) of usb_gadget_get_string is being executed, the dangling
memory is accessed, "BUG: KASAN: use-after-free" error occurs.
Cc: stable@vger.kernel.org
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/1615444961-13376-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9858af27e6 upstream.
Currently udc->ud.tcp_rx is being assigned twice, the second assignment
is incorrect, it should be to udc->ud.tcp_tx instead of rx. Fix this.
Fixes: 46613c9dfa ("usbip: fix vudc usbip_sockfd_store races leading to gpf")
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210311104445.7811-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 546aa0e4ea upstream.
Matthias reports that the Amazon Kindle automatically removes its
emulated media if it doesn't receive another SCSI command within about
one second after a SYNCHRONIZE CACHE. It does so even when the host
has sent a PREVENT MEDIUM REMOVAL command. The reason for this
behavior isn't clear, although it's not hard to make some guesses.
At any rate, the results can be unexpected for anyone who tries to
access the Kindle in an unusual fashion, and in theory they can lead
to data loss (for example, if one file is closed and synchronized
while other files are still in the middle of being written).
To avoid such problems, this patch creates a new usb-storage quirks
flag telling the driver always to issue a REQUEST SENSE following a
SYNCHRONIZE CACHE command, and adds an unusual_devs entry for the
Kindle with the flag set. This is sufficient to prevent the Kindle
from doing its automatic unload, without interfering with proper
operation.
Another possible way to deal with this would be to increase the
frequency of TEST UNIT READY polling that the kernel normally carries
out for removable-media storage devices. However that would increase
the overall load on the system and it is not as reliable, because the
user can override the polling interval. Changing the driver's
behavior is safer and has minimal overhead.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210317190654.GA497856@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
