commit 10fce53c0e upstream
The early ATAGS/DT mapping code uses SECTION_SHIFT to mask low order
bits of R2, and decides that no ATAGS/DTB were provided if the resulting
value is 0x0.
This means that on systems where DRAM starts at 0x0 (such as Raspberry
Pi), no explicit mapping of the DT will be created if R2 points into the
first 1 MB section of memory. This was not a problem before, because the
decompressed kernel is loaded at the base of DRAM and mapped using
sections as well, and so as long as the DT is referenced via a virtual
address that uses the same translation (the linear map, in this case),
things work fine.
However, commit 7a1be318f5 ("9012/1: move device tree mapping out of
linear region") changes this, and now the DT is referenced via a virtual
address that is disjoint from the linear mapping of DRAM, and so we need
the early code to create the DT mapping unconditionally.
So let's create the early DT mapping for any value of R2 != 0x0.
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc2933c133 upstream
Commit
149a3ffe62b9dbc3 ("9012/1: move device tree mapping out of linear region")
created a permanent, read-only section mapping of the device tree blob
provided by the firmware, and added a set of macros to get the base and
size of the virtually mapped FDT based on the physical address. However,
while the mapping code uses the SECTION_SIZE macro correctly, the macros
use PMD_SIZE instead, which means something entirely different on ARM when
using short descriptors, and is therefore not the right quantity to use
here. So replace PMD_SIZE with SECTION_SIZE. While at it, change the names
of the macro and its parameter to clarify that it returns the virtual
address of the start of the FDT, based on the physical address in memory.
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a1be318f5 upstream
On ARM, setting up the linear region is tricky, given the constraints
around placement and alignment of the memblocks, and how the kernel
itself as well as the DT are placed in physical memory.
Let's simplify matters a bit, by moving the device tree mapping to the
top of the address space, right between the end of the vmalloc region
and the start of the the fixmap region, and create a read-only mapping
for it that is independent of the size of the linear region, and how it
is organized.
Since this region was formerly used as a guard region, which will now be
populated fully on LPAE builds by this read-only mapping (which will
still be able to function as a guard region for stray writes), bump the
start of the [underutilized] fixmap region by 512 KB as well, to ensure
that there is always a proper guard region here. Doing so still leaves
ample room for the fixmap space, even with NR_CPUS set to its maximum
value of 32.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9a2f8b599 upstream
Before moving the DT mapping out of the linear region, let's prepare
for this change by removing all the phys-to-virt translations of the
__atags_pointer variable, and perform this translation only once at
setup time.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25de4ce5ed upstream.
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm percpu timers instead.
Let's configure dmtimer3 and 4 as percpu timers by default, and warn about
the issue if the dtb is not configured properly.
Let's do this as a single patch so it can be backported to v5.8 and later
kernels easily. Note that this patch depends on earlier timer-ti-dm
systimer posted mode fixes, and a preparatory clockevent patch
"clocksource/drivers/timer-ti-dm: Prepare to handle dra7 timer wrap issue".
For more information, please see the errata for "AM572x Sitara Processors
Silicon Revisions 1.1, 2.0":
https://www.ti.com/lit/er/sprz429m/sprz429m.pdf
The concept is based on earlier reference patches done by Tero Kristo and
Keerthy.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210323074326.28302-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25ab14cbe9 upstream.
Remove the inline asm with a DIVU instruction from `__div64_32' and use
plain C code for the intended DIVMOD calculation instead. GCC is smart
enough to know that both the quotient and the remainder are calculated
with single DIVU, so with ISAs up to R5 the same instruction is actually
produced with overall similar code.
For R6 compiled code will work, but separate DIVU and MODU instructions
will be produced, which are also interlocked, so scalar implementations
will likely not perform as well as older ISAs with their asynchronous MD
unit. Likely still faster then the generic algorithm though.
This removes a compilation error for R6 however where the original DIVU
instruction is not supported anymore and the MDU accumulator registers
have been removed and consequently GCC complains as to a constraint it
cannot find a register for:
In file included from ./include/linux/math.h:5,
from ./include/linux/kernel.h:13,
from mm/page-writeback.c:15:
./include/linux/math64.h: In function 'div_u64_rem':
./arch/mips/include/asm/div64.h:76:17: error: inconsistent operand constraints in an 'asm'
76 | __asm__("divu $0, %z1, %z2" \
| ^~~~~~~
./include/asm-generic/div64.h:245:25: note: in expansion of macro '__div64_32'
245 | __rem = __div64_32(&(n), __base); \
| ^~~~~~~~~~
./include/linux/math64.h:91:22: note: in expansion of macro 'do_div'
91 | *remainder = do_div(dividend, divisor);
| ^~~~~~
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0404s from 1.0445s with R3400
@40MHz. The module's MIPS I machine code has also shrunk by 12 bytes or
3 instructions.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1d337d45e upstream.
We already check the high part of the divident against zero to avoid the
costly DIVU instruction in that case, needed to reduce the high part of
the divident, so we may well check against the divisor instead and set
the high part of the quotient to zero right away. We need to treat the
high part the divident in that case though as the remainder that would
be calculated by the DIVU instruction we avoided.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0445s and 0.2619s from 1.0668s
and 0.2629s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c49f71f607 upstream.
Our current MIPS platform `__div64_32' handler is inactive, because it
is incorrectly only enabled for 64-bit configurations, for which generic
`do_div' code does not call it anyway.
The handler is not suitable for being called from there though as it
only calculates 32 bits of the quotient under the assumption the 64-bit
divident has been suitably reduced. Code for such reduction used to be
there, however it has been incorrectly removed with commit c21004cd5b
("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0."), which should
have only updated an obsoleted constraint for an inline asm involving
$hi and $lo register outputs, while possibly wiring the original MIPS
variant of the `do_div' macro as `__div64_32' handler for the generic
`do_div' implementation
Correct the handler as follows then:
- Revert most of the commit referred, however retaining the current
formatting, except for the final two instructions of the inline asm
sequence, which the original commit missed. Omit the original 64-bit
parts though.
- Rename the original `do_div' macro to `__div64_32'. Use the combined
`x' constraint referring to the MD accumulator as a whole, replacing
the original individual `h' and `l' constraints used for $hi and $lo
registers respectively, of which `h' has been obsoleted with GCC 4.4.
Update surrounding code accordingly.
We have since removed support for GCC versions before 4.9, so no need
for a special arrangement here; GCC has supported the `x' constraint
since forever anyway, or at least going back to 1991.
- Rename the `__base' local variable in `__div64_32' to `__radix' to
avoid a conflict with a local variable in `do_div'.
- Actually enable this code for 32-bit rather than 64-bit configurations
by qualifying it with BITS_PER_LONG being 32 instead of 64. Include
<asm/bitsperlong.h> for this macro rather than <linux/types.h> as we
don't need anything else.
- Finally include <asm-generic/div64.h> last rather than first.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0668s and 0.2629s from 2.1529s
and 0.5647s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
For a reference 64-bit `do_div' code where we have the DDIVU instruction
available to do the whole calculation right away averages at 0.0660s for
the latter CPU.
Fixes: c21004cd5b ("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0.")
Reported-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.30+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5104d7ffcf upstream.
Disable preemption when probing a user return MSR via RDSMR/WRMSR. If
the MSR holds a different value per logical CPU, the WRMSR could corrupt
the host's value if KVM is preempted between the RDMSR and WRMSR, and
then rescheduled on a different CPU.
Opportunistically land the helper in common x86, SVM will use the helper
in a future commit.
Fixes: 4be5341026 ("KVM: VMX: Initialize vmx->guest_msrs[] right after allocation")
Cc: stable@vger.kernel.org
Cc: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210504171734.1434054-6-seanjc@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aec21c04c upstream.
Clear KVM's RDPID capability if the ENABLE_RDTSCP secondary exec control is
unsupported. Despite being enumerated in a separate CPUID flag, RDPID is
bundled under the same VMCS control as RDTSCP and will #UD in VMX non-root
if ENABLE_RDTSCP is not enabled.
Fixes: 41cd02c6f7 ("kvm: x86: Expose RDPID in KVM_GET_SUPPORTED_CPUID")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210504171734.1434054-2-seanjc@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5c7e8425f upstream.
When enlightened VMCS is in use and nested state is migrated with
vmx_get_nested_state()/vmx_set_nested_state() KVM can't map evmcs
page right away: evmcs gpa is not 'struct kvm_vmx_nested_state_hdr'
and we can't read it from VP assist page because userspace may decide
to restore HV_X64_MSR_VP_ASSIST_PAGE after restoring nested state
(and QEMU, for example, does exactly that). To make sure eVMCS is
mapped /vmx_set_nested_state() raises KVM_REQ_GET_NESTED_STATE_PAGES
request.
Commit f2c7ef3ba9 ("KVM: nSVM: cancel KVM_REQ_GET_NESTED_STATE_PAGES
on nested vmexit") added KVM_REQ_GET_NESTED_STATE_PAGES clearing to
nested_vmx_vmexit() to make sure MSR permission bitmap is not switched
when an immediate exit from L2 to L1 happens right after migration (caused
by a pending event, for example). Unfortunately, in the exact same
situation we still need to have eVMCS mapped so
nested_sync_vmcs12_to_shadow() reflects changes in VMCS12 to eVMCS.
As a band-aid, restore nested_get_evmcs_page() when clearing
KVM_REQ_GET_NESTED_STATE_PAGES in nested_vmx_vmexit(). The 'fix' is far
from being ideal as we can't easily propagate possible failures and even if
we could, this is most likely already too late to do so. The whole
'KVM_REQ_GET_NESTED_STATE_PAGES' idea for mapping eVMCS after migration
seems to be fragile as we diverge too much from the 'native' path when
vmptr loading happens on vmx_set_nested_state().
Fixes: f2c7ef3ba9 ("KVM: nSVM: cancel KVM_REQ_GET_NESTED_STATE_PAGES on nested vmexit")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210503150854.1144255-2-vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85d0011264 upstream.
Do not advertise emulation support for RDPID if RDTSCP is unsupported.
RDPID emulation subtly relies on MSR_TSC_AUX to exist in hardware, as
both vmx_get_msr() and svm_get_msr() will return an error if the MSR is
unsupported, i.e. ctxt->ops->get_msr() will fail and the emulator will
inject a #UD.
Note, RDPID emulation also relies on RDTSCP being enabled in the guest,
but this is a KVM bug and will eventually be fixed.
Fixes: fb6d4d340e ("KVM: x86: emulate RDPID")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210504171734.1434054-3-seanjc@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f804f6d20 ]
syzbot reported a possible deadlock in pvclock_gtod_notify():
CPU 0 CPU 1
write_seqcount_begin(&tk_core.seq);
pvclock_gtod_notify() spin_lock(&pool->lock);
queue_work(..., &pvclock_gtod_work) ktime_get()
spin_lock(&pool->lock); do {
seq = read_seqcount_begin(tk_core.seq)
...
} while (read_seqcount_retry(&tk_core.seq, seq);
While this is unlikely to happen, it's possible.
Delegate queue_work() to irq_work() which postpones it until the
tk_core.seq write held region is left and interrupts are reenabled.
Fixes: 16e8d74d2d ("KVM: x86: notifier for clocksource changes")
Reported-by: syzbot+6beae4000559d41d80f8@syzkaller.appspotmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Message-Id: <87h7jgm1zy.ffs@nanos.tec.linutronix.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 594b27e677 ]
Nothing prevents the following:
pvclock_gtod_notify()
queue_work(system_long_wq, &pvclock_gtod_work);
...
remove_module(kvm);
...
work_queue_run()
pvclock_gtod_work() <- UAF
Ditto for any other operation on that workqueue list head which touches
pvclock_gtod_work after module removal.
Cancel the work in kvm_arch_exit() to prevent that.
Fixes: 16e8d74d2d ("KVM: x86: notifier for clocksource changes")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Message-Id: <87czu4onry.ffs@nanos.tec.linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d981dd1549 ]
Commit ee66e453db (KVM: lapic: Busy wait for timer to expire when
using hv_timer) tries to set ktime->expired_tscdeadline by checking
ktime->hv_timer_in_use since lapic timer oneshot/periodic modes which
are emulated by vmx preemption timer also get advanced, they leverage
the same vmx preemption timer logic with tsc-deadline mode. However,
ktime->hv_timer_in_use is cleared before apic_timer_expired() handling,
let's delay this clearing in preemption-disabled region.
Fixes: ee66e453db ("KVM: lapic: Busy wait for timer to expire when using hv_timer")
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1619608082-4187-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 588a513d34 upstream.
To ensure that instructions are observable in a new mapping, the arm64
set_pte_at() implementation cleans the D-cache and invalidates the
I-cache to the PoU. As an optimisation, this is only done on executable
mappings and the PG_dcache_clean page flag is set to avoid future cache
maintenance on the same page.
When two different processes map the same page (e.g. private executable
file or shared mapping) there's a potential race on checking and setting
PG_dcache_clean via set_pte_at() -> __sync_icache_dcache(). While on the
fault paths the page is locked (PG_locked), mprotect() does not take the
page lock. The result is that one process may see the PG_dcache_clean
flag set but the I/D cache maintenance not yet performed.
Avoid test_and_set_bit(PG_dcache_clean) in favour of separate test_bit()
and set_bit(). In the rare event of a race, the cache maintenance is
done twice.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Steven Price <steven.price@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210514095001.13236-1-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37a8024d26 upstream.
A valid implementation choice for the ChooseRandomNonExcludedTag()
pseudocode function used by IRG is to behave in the same way as with
GCR_EL1.RRND=0. This would mean that RGSR_EL1.SEED is used as an LFSR
which must have a non-zero value in order for IRG to properly produce
pseudorandom numbers. However, RGSR_EL1 is reset to an UNKNOWN value
on soft reset and thus may reset to 0. Therefore we must initialize
RGSR_EL1.SEED to a non-zero value in order to ensure that IRG behaves
as expected.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Fixes: 3b714d24ef ("arm64: mte: CPU feature detection and initial sysreg configuration")
Cc: <stable@vger.kernel.org> # 5.10
Link: https://linux-review.googlesource.com/id/I2b089b6c7d6f17ee37e2f0db7df5ad5bcc04526c
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210507185905.1745402-1-pcc@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aec86b052d upstream.
The entry flush mitigation can be enabled/disabled at runtime via a
debugfs file (entry_flush), which causes the kernel to patch itself to
enable/disable the relevant mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
sleeper[15639]: segfault (11) at c000000000004c20 nip c000000000004c20 lr c000000000004c20
Shows that we returned to userspace with a corrupted LR that points into
the kernel, due to executing the partially patched call to the fallback
entry flush (ie. we missed the LR restore).
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
Fixes: f79643787e ("powerpc/64s: flush L1D on kernel entry")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210506044959.1298123-2-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ec7791bae upstream.
The STF (store-to-load forwarding) barrier mitigation can be
enabled/disabled at runtime via a debugfs file (stf_barrier), which
causes the kernel to patch itself to enable/disable the relevant
mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
User access of kernel address (c00000003fff5af0) - exploit attempt? (uid: 0)
segfault (11) at c00000003fff5af0 nip 7fff8ad12198 lr 7fff8ad121f8 code 1
code: 40820128 e93c00d0 e9290058 7c292840 40810058 38600000 4bfd9a81 e8410018
code: 2c030006 41810154 3860ffb6 e9210098 <e94d8ff0> 7d295279 39400000 40820a3c
Shows that we returned to userspace without restoring the user r13
value, due to executing the partially patched STF exit code.
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
Fixes: a048a07d7f ("powerpc/64s: Add support for a store forwarding barrier at kernel entry/exit")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210506044959.1298123-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d5e4640e5 upstream.
Commit 4af22ded0e ("arc: fix memory initialization for systems
with two memory banks") fixed highmem, but for the PAE case it causes
bug messages:
| BUG: Bad page state in process swapper pfn:80000
| page:(ptrval) refcount:0 mapcount:1 mapping:00000000 index:0x0 pfn:0x80000 flags: 0x0()
| raw: 00000000 00000100 00000122 00000000 00000000 00000000 00000000 00000000
| raw: 00000000
| page dumped because: nonzero mapcount
| Modules linked in:
| CPU: 0 PID: 0 Comm: swapper Not tainted 5.12.0-rc5-00003-g1e43c377a79f #1
This is because the fix expects highmem to be always less than
lowmem and uses min_low_pfn as an upper zone border for highmem.
max_high_pfn should be ok for both highmem and highmem+PAE cases.
Fixes: 4af22ded0e ("arc: fix memory initialization for systems with two memory banks")
Signed-off-by: Vladimir Isaev <isaev@synopsys.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: stable@vger.kernel.org #5.8 onwards
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5f756d8c6 upstream.
32-bit PAGE_MASK can not be used as a mask for physical addresses
when PAE is enabled. PAGE_MASK_PHYS must be used for physical
addresses instead of PAGE_MASK.
Without this, init gets SIGSEGV if pte_modify was called:
| potentially unexpected fatal signal 11.
| Path: /bin/busybox
| CPU: 0 PID: 1 Comm: init Not tainted 5.12.0-rc5-00003-g1e43c377a79f-dirty
| Insn could not be fetched
| @No matching VMA found
| ECR: 0x00040000 EFA: 0x00000000 ERET: 0x00000000
| STAT: 0x80080082 [IE U ] BTA: 0x00000000
| SP: 0x5f9ffe44 FP: 0x00000000 BLK: 0xaf3d4
| LPS: 0x000d093e LPE: 0x000d0950 LPC: 0x00000000
| r00: 0x00000002 r01: 0x5f9fff14 r02: 0x5f9fff20
| ...
| Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Signed-off-by: Vladimir Isaev <isaev@synopsys.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3433adc8bd upstream.
We have NR_syscall syscalls from [0 .. NR_syscall-1].
However the check for invalid syscall number is "> NR_syscall" as
opposed to >=. This off-by-one error erronesously allows "NR_syscall"
to be treated as valid syscall causeing out-of-bounds access into
syscall-call table ensuing a crash (holes within syscall table have a
invalid-entry handler but this is beyond the array implementing the
table).
This problem showed up on v5.6 kernel when testing glibc 2.33 (v5.10
kernel capable, includng faccessat2 syscall 439). The v5.6 kernel has
NR_syscalls=439 (0 to 438). Due to the bug, 439 passed by glibc was
not handled as -ENOSYS but processed leading to a crash.
Link: https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/48
Reported-by: Shahab Vahedi <shahab@synopsys.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d6a38da8e ]
Zenghui reports that booting a kernel with "irqchip.gicv3_pseudo_nmi=1"
on the command line hits a warning during kernel entry, due to the way
we manipulate the PMR.
Early in the entry sequence, we call lockdep_hardirqs_off() to inform
lockdep that interrupts have been masked (as the HW sets DAIF wqhen
entering an exception). Architecturally PMR_EL1 is not affected by
exception entry, and we don't set GIC_PRIO_PSR_I_SET in the PMR early in
the exception entry sequence, so early in exception entry the PMR can
indicate that interrupts are unmasked even though they are masked by
DAIF.
If DEBUG_LOCKDEP is selected, lockdep_hardirqs_off() will check that
interrupts are masked, before we set GIC_PRIO_PSR_I_SET in any of the
exception entry paths, and hence lockdep_hardirqs_off() will WARN() that
something is amiss.
We can avoid this by consistently setting GIC_PRIO_PSR_I_SET during
exception entry so that kernel code sees a consistent environment. We
must also update local_daif_inherit() to undo this, as currently only
touches DAIF. For other paths, local_daif_restore() will update both
DAIF and the PMR. With this done, we can remove the existing special
cases which set this later in the entry code.
We always use (GIC_PRIO_IRQON | GIC_PRIO_PSR_I_SET) for consistency with
local_daif_save(), as this will warn if it ever encounters
(GIC_PRIO_IRQOFF | GIC_PRIO_PSR_I_SET), and never sets this itself. This
matches the gic_prio_kentry_setup that we have to retain for
ret_to_user.
The original splat from Zenghui's report was:
| DEBUG_LOCKS_WARN_ON(!irqs_disabled())
| WARNING: CPU: 3 PID: 125 at kernel/locking/lockdep.c:4258 lockdep_hardirqs_off+0xd4/0xe8
| Modules linked in:
| CPU: 3 PID: 125 Comm: modprobe Tainted: G W 5.12.0-rc8+ #463
| Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
| pstate: 604003c5 (nZCv DAIF +PAN -UAO -TCO BTYPE=--)
| pc : lockdep_hardirqs_off+0xd4/0xe8
| lr : lockdep_hardirqs_off+0xd4/0xe8
| sp : ffff80002a39bad0
| pmr_save: 000000e0
| x29: ffff80002a39bad0 x28: ffff0000de214bc0
| x27: ffff0000de1c0400 x26: 000000000049b328
| x25: 0000000000406f30 x24: ffff0000de1c00a0
| x23: 0000000020400005 x22: ffff8000105f747c
| x21: 0000000096000044 x20: 0000000000498ef9
| x19: ffff80002a39bc88 x18: ffffffffffffffff
| x17: 0000000000000000 x16: ffff800011c61eb0
| x15: ffff800011700a88 x14: 0720072007200720
| x13: 0720072007200720 x12: 0720072007200720
| x11: 0720072007200720 x10: 0720072007200720
| x9 : ffff80002a39bad0 x8 : ffff80002a39bad0
| x7 : ffff8000119f0800 x6 : c0000000ffff7fff
| x5 : ffff8000119f07a8 x4 : 0000000000000001
| x3 : 9bcdab23f2432800 x2 : ffff800011730538
| x1 : 9bcdab23f2432800 x0 : 0000000000000000
| Call trace:
| lockdep_hardirqs_off+0xd4/0xe8
| enter_from_kernel_mode.isra.5+0x7c/0xa8
| el1_abort+0x24/0x100
| el1_sync_handler+0x80/0xd0
| el1_sync+0x6c/0x100
| __arch_clear_user+0xc/0x90
| load_elf_binary+0x9fc/0x1450
| bprm_execve+0x404/0x880
| kernel_execve+0x180/0x188
| call_usermodehelper_exec_async+0xdc/0x158
| ret_from_fork+0x10/0x18
Fixes: 23529049c6 ("arm64: entry: fix non-NMI user<->kernel transitions")
Fixes: 7cd1ea1010 ("arm64: entry: fix non-NMI kernel<->kernel transitions")
Fixes: f0cd5ac1e4 ("arm64: entry: fix NMI {user, kernel}->kernel transitions")
Fixes: 2a9b3e6ac6 ("arm64: entry: fix EL1 debug transitions")
Link: https://lore.kernel.org/r/f4012761-026f-4e51-3a0c-7524e434e8b3@huawei.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210428111555.50880-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eb563cdab ]
In subsequent patches we'll allow an FIQ handler to be registered, and
FIQ exceptions will need to be triaged very similarly to IRQ exceptions.
So that we can reuse the existing logic, this patch factors the IRQ
triage logic out into macros that can be reused for FIQ.
The macros are named to follow the elX_foo_handler scheme used by the C
exception handlers. For consistency with other top-level exception
handlers, the kernel_entry/kernel_exit logic is not moved into the
macros. As FIQ will use a different C handler, this handler name is
provided as an argument to the macros.
There should be no functional change as a result of this patch.
Signed-off-by: Marc Zyngier <maz@kernel.org>
[Mark: rework macros, commit message, rebase before DAIF rework]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Hector Martin <marcan@marcan.st>
Cc: James Morse <james.morse@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210315115629.57191-5-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 533b4f3a78 ]
We should return a negative error code upon failure in
riscv_hartid_to_cpuid() instead of NR_CPUS. This is also
aligned with all uses of riscv_hartid_to_cpuid() which
expect negative error code upon failure.
Fixes: 6825c7a80f ("RISC-V: Add logical CPU indexing for RISC-V")
Fixes: f99fb607fb ("RISC-V: Use Linux logical CPU number instead of hartid")
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a506bd5756 ]
The commit 1879445dfa ("perf/core: Set event's default
::overflow_handler()") set a default event->overflow_handler in
perf_event_alloc(), and replace the check event->overflow_handler with
is_default_overflow_handler(), but one is missing.
Currently, the bp->overflow_handler can not be NULL. As a result,
enable_single_step() is always not invoked.
Comments from Zhen Lei:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/20210207105934.2001-1-thunder.leizhen@huawei.com/
Fixes: 1879445dfa ("perf/core: Set event's default ::overflow_handler()")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Cc: Wang Nan <wangnan0@huawei.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99e729bd40 ]
Noticed failure as a crash on ia64 when tried to symbolize all backtraces
collected by page_owner=on:
$ cat /sys/kernel/debug/page_owner
<oops>
CPU: 1 PID: 2074 Comm: cat Not tainted 5.12.0-rc4 #226
Hardware name: hp server rx3600, BIOS 04.03 04/08/2008
ip is at dereference_module_function_descriptor+0x41/0x100
Crash happens at dereference_module_function_descriptor() due to
use-after-free when dereferencing ".opd" section header.
All section headers are already freed after module is laoded successfully.
To keep symbolizer working the change stores ".opd" address and size after
module is relocated to a new place and before section headers are
discarded.
To make similar errors less obscure module_finalize() now zeroes out all
variables relevant to module loading only.
Link: https://lkml.kernel.org/r/20210403074803.3309096-1-slyfox@gentoo.org
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc7130bf11 ]
The IOMMU table is divided into pools for concurrent mappings and each
pool has a separate spinlock. When taking the ownership of an IOMMU group
to pass through a device to a VM, we lock these spinlocks which triggers
a false negative warning in lockdep (below).
This fixes it by annotating the large pool's spinlock as a nest lock
which makes lockdep not complaining when locking nested locks if
the nest lock is locked already.
===
WARNING: possible recursive locking detected
5.11.0-le_syzkaller_a+fstn1 #100 Not tainted
--------------------------------------------
qemu-system-ppc/4129 is trying to acquire lock:
c0000000119bddb0 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
but task is already holding lock:
c0000000119bdd30 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(p->lock)/1);
lock(&(p->lock)/1);
===
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210301063653.51003-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed8029d7b4 ]
RCU complains about us calling printk() from an offline CPU:
=============================
WARNING: suspicious RCU usage
5.12.0-rc7-02874-g7cf90e481cb8 #1 Not tainted
-----------------------------
kernel/locking/lockdep.c:3568 RCU-list traversed in non-reader section!!
other info that might help us debug this:
RCU used illegally from offline CPU!
rcu_scheduler_active = 2, debug_locks = 1
no locks held by swapper/0/0.
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.12.0-rc7-02874-g7cf90e481cb8 #1
Call Trace:
dump_stack+0xec/0x144 (unreliable)
lockdep_rcu_suspicious+0x124/0x144
__lock_acquire+0x1098/0x28b0
lock_acquire+0x128/0x600
_raw_spin_lock_irqsave+0x6c/0xc0
down_trylock+0x2c/0x70
__down_trylock_console_sem+0x60/0x140
vprintk_emit+0x1a8/0x4b0
vprintk_func+0xcc/0x200
printk+0x40/0x54
pseries_cpu_offline_self+0xc0/0x120
arch_cpu_idle_dead+0x54/0x70
do_idle+0x174/0x4a0
cpu_startup_entry+0x38/0x40
rest_init+0x268/0x388
start_kernel+0x748/0x790
start_here_common+0x1c/0x614
Which happens because by the time we get to rtas_stop_self() we are
already offline. In addition the message can be spammy, and is not that
helpful for users, so remove it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210418135413.1204031-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5d6a3e73a ]
While removing large number of mappings from hash page tables for
large memory systems as soft-lockup is reported because of the time
spent inside htap_remove_mapping() like one below:
watchdog: BUG: soft lockup - CPU#8 stuck for 23s!
<snip>
NIP plpar_hcall+0x38/0x58
LR pSeries_lpar_hpte_invalidate+0x68/0xb0
Call Trace:
0x1fffffffffff000 (unreliable)
pSeries_lpar_hpte_removebolted+0x9c/0x230
hash__remove_section_mapping+0xec/0x1c0
remove_section_mapping+0x28/0x3c
arch_remove_memory+0xfc/0x150
devm_memremap_pages_release+0x180/0x2f0
devm_action_release+0x30/0x50
release_nodes+0x28c/0x300
device_release_driver_internal+0x16c/0x280
unbind_store+0x124/0x170
drv_attr_store+0x44/0x60
sysfs_kf_write+0x64/0x90
kernfs_fop_write+0x1b0/0x290
__vfs_write+0x3c/0x70
vfs_write+0xd4/0x270
ksys_write+0xdc/0x130
system_call+0x5c/0x70
Fix this by adding a cond_resched() to the loop in
htap_remove_mapping() that issues hcall to remove hpte mapping. The
call to cond_resched() is issued every HZ jiffies which should prevent
the soft-lockup from being reported.
Suggested-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210404163148.321346-1-vaibhav@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e65c52ec7 ]
Loongson64 processors have a writecombine issue that maybe failed to
write back framebuffer used with ATI Radeon or AMD GPU at times, after
commit 8a08e50cee ("drm: Permit video-buffers writecombine mapping
for MIPS"), there exists some errors such as blurred screen and lockup,
and so on.
[ 60.958721] radeon 0000:03:00.0: ring 0 stalled for more than 10079msec
[ 60.965315] radeon 0000:03:00.0: GPU lockup (current fence id 0x0000000000000112 last fence id 0x000000000000011d on ring 0)
[ 60.976525] radeon 0000:03:00.0: ring 3 stalled for more than 10086msec
[ 60.983156] radeon 0000:03:00.0: GPU lockup (current fence id 0x0000000000000374 last fence id 0x00000000000003a8 on ring 3)
As discussed earlier [1], it might be better to disable writecombine
on the CPU detection side because the root cause is unknown now.
Actually, this patch is a temporary solution to just make it work well,
it is not a proper and final solution, I hope someone will have a better
solution to fix this issue in the future.
[1] https://lore.kernel.org/patchwork/patch/1285542/
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4719f5bb6 ]
The check of the emergency context initialisation in
vmap_stack_overflow is buggy for the SMP case, as it
compares r1 with 0 while in the SMP case r1 is offseted
by the CPU id.
Instead of fixing it, just perform static initialisation
of the first emergency context.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4a67ba422be75713286dca0c86ee0d3df2eb6dfa.1615552867.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a217a6593c upstream.
In VMX, the host NMI handler needs to be invoked after NMI VM-Exit.
Before commit 1a5488ef0d ("KVM: VMX: Invoke NMI handler via indirect
call instead of INTn"), this was done by INTn ("int $2"). But INTn
microcode is relatively expensive, so the commit reworked NMI VM-Exit
handling to invoke the kernel handler by function call.
But this missed a detail. The NMI entry point for direct invocation is
fetched from the IDT table and called on the kernel stack. But on 64-bit
the NMI entry installed in the IDT expects to be invoked on the IST stack.
It relies on the "NMI executing" variable on the IST stack to work
correctly, which is at a fixed position in the IST stack. When the entry
point is unexpectedly called on the kernel stack, the RSP-addressed "NMI
executing" variable is obviously also on the kernel stack and is
"uninitialized" and can cause the NMI entry code to run in the wrong way.
Provide a non-ist entry point for VMX which shares the C-function with
the regular NMI entry and invoke the new asm entry point instead.
On 32-bit this just maps to the regular NMI entry point as 32-bit has no
ISTs and is not affected.
[ tglx: Made it independent for backporting, massaged changelog ]
Fixes: 1a5488ef0d ("KVM: VMX: Invoke NMI handler via indirect call instead of INTn")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Lai Jiangshan <laijs@linux.alibaba.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87r1imi8i1.ffs@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5e2184d15 upstream.
Remove the update_pte() shadow paging logic, which was obsoleted by
commit 4731d4c7a0 ("KVM: MMU: out of sync shadow core"), but never
removed. As pointed out by Yu, KVM never write protects leaf page
tables for the purposes of shadow paging, and instead marks their
associated shadow page as unsync so that the guest can write PTEs at
will.
The update_pte() path, which predates the unsync logic, optimizes COW
scenarios by refreshing leaf SPTEs when they are written, as opposed to
zapping the SPTE, restarting the guest, and installing the new SPTE on
the subsequent fault. Since KVM no longer write-protects leaf page
tables, update_pte() is unreachable and can be dropped.
Reported-by: Yu Zhang <yu.c.zhang@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210115004051.4099250-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d78050ee35 upstream.
With the introduction of a dynamic ZONE_DMA range based on DT or IORT
information, there's no need for CMA allocations from the wider
ZONE_DMA32 since on most platforms ZONE_DMA will cover the 32-bit
addressable range. Remove the arm64_dma32_phys_limit and set
arm64_dma_phys_limit to cover the smallest DMA range required on the
platform. CMA allocation and crashkernel reservation now go in the
dynamically sized ZONE_DMA, allowing correct functionality on RPi4.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> # On RPi4B
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3db00b79d ]
When enabled local debugging via `#define EFI_DEBUG 1` noticed build
failure:
arch/ia64/kernel/efi.c:564:8: error: 'i' undeclared (first use in this function)
While at it fixed benign string format mismatches visible only when
EFI_DEBUG is enabled:
arch/ia64/kernel/efi.c:589:11:
warning: format '%lx' expects argument of type 'long unsigned int',
but argument 5 has type 'u64' {aka 'long long unsigned int'} [-Wformat=]
Link: https://lkml.kernel.org/r/20210328212246.685601-1-slyfox@gentoo.org
Fixes: 14fb420909 ("efi: Merge EFI system table revision and vendor checks")
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbdd096a5a ]
Disable pass-through of the FS and GS base MSRs for 32-bit KVM. Intel's
SDM unequivocally states that the MSRs exist if and only if the CPU
supports x86-64. FS_BASE and GS_BASE are mostly a non-issue; a clever
guest could opportunistically use the MSRs without issue. KERNEL_GS_BASE
is a bigger problem, as a clever guest would subtly be broken if it were
migrated, as KVM disallows software access to the MSRs, and unlike the
direct variants, KERNEL_GS_BASE needs to be explicitly migrated as it's
not captured in the VMCS.
Fixes: 25c5f225be ("KVM: VMX: Enable MSR Bitmap feature")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210422023831.3473491-1-seanjc@google.com>
[*NOT* for stable kernels. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcabb06bf1 ]
UniPhier LD20 and PXs3 boards have RTL8211E ethernet phy, and the phy have
the RX/TX delays of RGMII interface using pull-ups on the RXDLY and TXDLY
pins.
After the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: c73730ee4c ("arm64: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ba585cc5b ]
UniPhier PXs2 boards have RTL8211E ethernet phy, and the phy have the RX/TX
delays of RGMII interface using pull-ups on the RXDLY and TXDLY pins.
After the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: e3cc931921 ("ARM: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66d9b74928 ]
Memory events (mem-loads and mem-stores) currently use the threshold
event selection as issue to finish. Power10 supports issue to complete
as part of thresholding which is more appropriate for mem-loads and
mem-stores. Hence fix the event code for memory events to use issue
to complete.
Fixes: a64e697cef ("powerpc/perf: power10 Performance Monitoring support")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1614840015-1535-1-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ccba66d4d ]
At the time being, the fixmap area is defined at the top of
the address space or just below KASAN.
This definition is not valid for PPC64.
For PPC64, use the top of the I/O space.
Because of circular dependencies, it is not possible to include
asm/fixmap.h in asm/book3s/64/pgtable.h , so define a fixed size
AREA at the top of the I/O space for fixmap and ensure during
build that the size is big enough.
Fixes: 265c3491c4 ("powerpc: Add support for GENERIC_EARLY_IOREMAP")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0d51620eacf036d683d1a3c41328f69adb601dc0.1618925560.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9e46d344e ]
If the VM entry/exit controls for loading/saving MSR_EFER are either
not available (an older processor or explicitly disabled) or not
used (host and guest values are the same), reading GUEST_IA32_EFER
from the VMCS returns an inaccurate value.
Because of this, in dump_vmcs() don't use GUEST_IA32_EFER to decide
whether to print the PDPTRs - always do so if the fields exist.
Fixes: 4eb64dce8d ("KVM: x86: dump VMCS on invalid entry")
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20210318120841.133123-2-david.edmondson@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c47f892d7a ]
Daniel reported that with Commit 4ca234a9cb ("powerpc/smp: Stop
updating cpu_core_mask") QEMU was unable to set single NUMA node SMP
topologies such as:
-smp 8,maxcpus=8,cores=2,threads=2,sockets=2
i.e he expected 2 sockets in one NUMA node.
The above commit helped to reduce boot time on Large Systems for
example 4096 vCPU single socket QEMU instance. PAPR is silent on
having more than one socket within a NUMA node.
cpu_core_mask and cpu_cpu_mask for any CPU would be same unless the
number of sockets is different from the number of NUMA nodes.
One option is to reintroduce cpu_core_mask but use a slightly
different method to arrive at the cpu_core_mask. Previously each CPU's
chip-id would be compared with all other CPU's chip-id to verify if
both the CPUs were related at the chip level. Now if a CPU 'A' is
found related / (unrelated) to another CPU 'B', all the thread
siblings of 'A' and thread siblings of 'B' are automatically marked as
related / (unrelated).
Also if a platform doesn't support ibm,chip-id property, i.e its
cpu_to_chip_id returns -1, cpu_core_map holds a copy of
cpu_cpu_mask().
Fixes: 4ca234a9cb ("powerpc/smp: Stop updating cpu_core_mask")
Reported-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210415120934.232271-2-srikar@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38d0b1c9ce ]
The pci_bus->bridge reference may no longer be valid after
pci_bus_remove() resulting in passing a bad value to device_unregister()
for the associated bridge device.
Store the host_bridge reference in a separate variable prior to
pci_bus_remove().
Fixes: 7340056567 ("powerpc/pci: Reorder pci bus/bridge unregistration during PHB removal")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210211182435.47968-1-tyreld@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ecb9dc158 ]
Mirror commit aeba3731b1 ("powerpc/pci: Fix IO space breakage after
of_pci_range_to_resource() change").
Most MIPS platforms do not define PCI_IOBASE, nor implement
pci_address_to_pio(). Moreover, IO_SPACE_LIMIT is 0xffff for most MIPS
platforms. of_pci_range_to_resource passes the _start address_ of the IO
range into pci_address_to_pio, which then checks it against
IO_SPACE_LIMIT and fails, because for MIPS platforms that use
pci-legacy (pci-lantiq, pci-rt3883, pci-mt7620), IO ranges start much
higher than 0xffff.
In fact, pci-mt7621 in staging already works around this problem, see
commit 09dd629eea ("staging: mt7621-pci: fix io space and properly set
resource limits")
So just stop using of_pci_range_to_resource, which does not work for
MIPS.
Fixes PCI errors like:
pci_bus 0000:00: root bus resource [io 0xffffffff]
Fixes: 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO resources")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33e4bc5946 ]
When under xmon, the "dxi" command dumps the state of the XIVE
interrupts. If an interrupt number is specified, only the state of
the associated XIVE interrupt is dumped. This form of the command
lacks an irq_data parameter which is nevertheless used by
xmon_xive_get_irq_config(), leading to an xmon crash.
Fix that by doing a lookup in the system IRQ mapping to query the IRQ
descriptor data. Invalid interrupt numbers, or not belonging to the
XIVE IRQ domain, OPAL event interrupt number for instance, should be
caught by the previous query done at the firmware level.
Fixes: 97ef275077 ("powerpc/xive: Fix xmon support on the PowerNV platform")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210331144514.892250-8-clg@kaod.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
