[ Upstream commit 15395ec468 ]
Unlike other supported adapters, 2.5G and 5G use different
PHY type identifiers for reading/writing PHY settings
and for reading link status. This commit introduces
separate PHY identifiers for these two operation types.
Fixes: 2e45d3f467 ("i40e: Add support for X710 B/P & SFP+ cards")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61343e6da7 ]
When FEC mode was changed the link didn't know it because
the link was not reset and new parameters were not negotiated.
Set a flag 'I40E_AQ_PHY_ENABLE_ATOMIC_LINK' in 'abilities'
to restart the link and make it run with the new settings.
Fixes: 1d96340196 ("i40e: Add support FEC configuration for Fortville 25G")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38318f23a7 ]
Currently the call to i40e_client_del_instance frees the object
pf->cinst, however pf->cinst->lan_info is being accessed after
the free. Fix this by adding the missing return.
Addresses-Coverity: ("Read from pointer after free")
Fixes: 7b0b1a6d0a ("i40e: Disable iWARP VSI PETCP_ENA flag on netdev down events")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae4393dfd4 ]
Commit 12738ac475 ("i40e: Fix sparse errors in i40e_txrx.c") broke
XDP support in the i40e driver. That commit was fixing a sparse error
in the code by introducing a new variable xdp_res instead of
overloading this into the skb pointer. The problem is that the code
later uses the skb pointer in if statements and these where not
extended to also test for the new xdp_res variable. Fix this by adding
the correct tests for xdp_res in these places.
The skb pointer was used to store the result of the XDP program by
overloading the results in the error pointer
ERR_PTR(-result). Therefore, the allocation failure test that used to
only test for !skb now need to be extended to also consider !xdp_res.
i40e_cleanup_headers() had a check that based on the skb value being
an error pointer, i.e. a result from the XDP program != XDP_PASS, and
if so start to process a new packet immediately, instead of populating
skb fields and sending the skb to the stack. This check is not needed
anymore, since we have added an explicit test for xdp_res being set
and if so just do continue to pick the next packet from the NIC.
Fixes: 12738ac475 ("i40e: Fix sparse errors in i40e_txrx.c")
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e04b2cfe61 ]
The m_can_start_xmit() function checks if the cdev->tx_skb is NULL and
returns with NETDEV_TX_BUSY in case tx_sbk is not NULL.
There is a race condition in the m_can_tx_work_queue(), where first
the skb is send to the driver and then the case tx_sbk is set to NULL.
A TX complete IRQ might come in between and wake the queue, which
results in tx_skb not being cleared yet.
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Tested-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03c427147b ]
Since 8ce8c0abcb the driver queues work via priv->restart_work when
resuming after suspend, even when the interface was not previously
enabled. This causes a null dereference error as the workqueue is only
allocated and initialized in mcp251x_open().
To fix this we move the workqueue init to mcp251x_can_probe() as there
is no reason to do it later and repeat it whenever mcp251x_open() is
called.
Fixes: 8ce8c0abcb ("can: mcp251x: only reset hardware as required")
Link: https://lore.kernel.org/r/17d5d714-b468-482f-f37a-482e3d6df84e@kontron.de
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[mkl: fix error handling in mcp251x_stop()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4376ea42db ]
This patch adds the missing can_rx_offload_del(), that must be called
if mcp251xfd_register() fails.
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Link: https://lore.kernel.org/r/20210504091838.1109047-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c7a94286e ]
In promiscuous mode Receive All bit is set in GMAC packet filter register,
but outside promiscuous mode Receive All bit is not cleared,
which resulted in all network packets are received when toggle (ON/OFF)
the promiscuous mode.
Fixes: e0f9956a38 ("net: stmmac: Add option for VLAN filter fail queue enable")
Signed-off-by: Ramesh Babu B <ramesh.babu.b@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 643001b47a ]
In enic_hard_start_xmit, it calls enic_queue_wq_skb(). Inside
enic_queue_wq_skb, if some error happens, the skb will be freed
by dev_kfree_skb(skb). But the freed skb is still used in
skb_tx_timestamp(skb).
My patch makes enic_queue_wq_skb() return error and goto spin_unlock()
incase of error. The solution is provided by Govind.
See https://lkml.org/lkml/2021/4/30/961.
Fixes: fb7516d424 ("enic: add sw timestamp support")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Acked-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 472497d0bd ]
If selftest and reset are performed at the same time, the phy
loopback setting may be still in enable state after the reset,
and device cannot link up. So fix this issue by disabling phy
loopback before phy_start().
Fixes: 256727da73 ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b416e872be ]
Currently, netif_tx_stop_all_queues() is used to ensure that
the xmit is not running, but for the concurrent case it will
not take effect, since netif_tx_stop_all_queues() just sets
a flag without locking to indicate that the xmit queue(s)
should not be run.
So use netif_tx_disable() to replace netif_tx_stop_all_queues(),
it takes the xmit queue lock while marking the queue stopped.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 905416f18f ]
When skb->ip_summed is CHECKSUM_PARTIAL, for non-tunnel udp packet,
which has a dest port as the IANA assigned, the hardware is expected
to do the checksum offload, but the hardware whose version is below
V3 will not do the checksum offload when udp dest port is 4790.
So fixes it by doing the checksum in software for this case.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4047aac4e ]
In some cases, the device is not initialized because reset failed.
If another task calls hns3_reset_notify_up_enet() before reset
retry, it will cause an error since uninitialized pointer access.
So add check for HNS3_NIC_STATE_INITED before calling
hns3_nic_net_open() in hns3_reset_notify_up_enet().
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 568a54bdf7 ]
The message sent to VF should be initialized, otherwise random
value of some contents may cause improper processing by the target.
So add a initialization to message in hclge_get_link_mode().
Fixes: 9194d18b05 ("net: hns3: fix the problem that the supported port is empty")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2867298dd4 ]
According to the UM, the type and enable status of igu_egu_hw_err
should be configured separately. Currently, the type field is
incorrect when disable this error. So fix it by configuring these
two fields separately.
Fixes: bf1faf9415 ("net: hns3: Add enable and process hw errors from IGU, EGU and NCSI")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fbf359bb2 ]
Support VF device IDs used by the Hyper-V hypervisor.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f57d8c40f ]
The VLAN ID in the rx descriptor is only valid if the RX_DMA_VTAG bit is
set. Fixes frames wrongly marked with VLAN tags.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: fix commit message]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a0e880b02 ]
Both iavf_free_all_tx_resources() and iavf_free_all_rx_resources() have
already been called in the very same function.
Remove the duplicate calls.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 130f634da1 ]
Function qtnf_event_handle_external_auth calls memcpy without
checking the length.
A user could control that length and trigger a buffer overflow.
Fix by checking the length is within the maximum allowed size.
Signed-off-by: Lee Gibson <leegib@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419145842.345787-1-leegib@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb43e5718d ]
Fix the following out-of-bounds warnings by adding a new structure
wl3501_req instead of duplicating the same members in structure
wl3501_join_req and wl3501_scan_confirm:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [39, 108] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 36 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [25, 95] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 22 [-Warray-bounds]
Refactor the code, accordingly:
$ pahole -C wl3501_req drivers/net/wireless/wl3501_cs.o
struct wl3501_req {
u16 beacon_period; /* 0 2 */
u16 dtim_period; /* 2 2 */
u16 cap_info; /* 4 2 */
u8 bss_type; /* 6 1 */
u8 bssid[6]; /* 7 6 */
struct iw_mgmt_essid_pset ssid; /* 13 34 */
struct iw_mgmt_ds_pset ds_pset; /* 47 3 */
struct iw_mgmt_cf_pset cf_pset; /* 50 8 */
struct iw_mgmt_ibss_pset ibss_pset; /* 58 4 */
struct iw_mgmt_data_rset bss_basic_rset; /* 62 10 */
/* size: 72, cachelines: 2, members: 10 */
/* last cacheline: 8 bytes */
};
$ pahole -C wl3501_join_req drivers/net/wireless/wl3501_cs.o
struct wl3501_join_req {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 reserved; /* 3 1 */
struct iw_mgmt_data_rset operational_rset; /* 4 10 */
u16 reserved2; /* 14 2 */
u16 timeout; /* 16 2 */
u16 probe_delay; /* 18 2 */
u8 timestamp[8]; /* 20 8 */
u8 local_time[8]; /* 28 8 */
struct wl3501_req req; /* 36 72 */
/* size: 108, cachelines: 2, members: 10 */
/* last cacheline: 44 bytes */
};
$ pahole -C wl3501_scan_confirm drivers/net/wireless/wl3501_cs.o
struct wl3501_scan_confirm {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 reserved; /* 3 1 */
u16 status; /* 4 2 */
char timestamp[8]; /* 6 8 */
char localtime[8]; /* 14 8 */
struct wl3501_req req; /* 22 72 */
/* --- cacheline 1 boundary (64 bytes) was 30 bytes ago --- */
u8 rssi; /* 94 1 */
/* size: 96, cachelines: 2, members: 8 */
/* padding: 1 */
/* last cacheline: 32 bytes */
};
The problem is that the original code is trying to copy data into a
bunch of struct members adjacent to each other in a single call to
memcpy(). Now that a new struct wl3501_req enclosing all those adjacent
members is introduced, memcpy() doesn't overrun the length of
&sig.beacon_period and &this->bss_set[i].beacon_period, because the
address of the new struct object _req_ is used as the destination,
instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1fbaf516da763b50edac47d792a9145aa4482e29.1618442265.git.gustavoars@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820aa37638 ]
Fix the following out-of-bounds warnings by enclosing structure members
daddr and saddr into new struct addr, in structures wl3501_md_req and
wl3501_md_ind:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
Refactor the code, accordingly:
$ pahole -C wl3501_md_req drivers/net/wireless/wl3501_cs.o
struct wl3501_md_req {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 routing; /* 3 1 */
u16 data; /* 4 2 */
u16 size; /* 6 2 */
u8 pri; /* 8 1 */
u8 service_class; /* 9 1 */
struct {
u8 daddr[6]; /* 10 6 */
u8 saddr[6]; /* 16 6 */
} addr; /* 10 12 */
/* size: 22, cachelines: 1, members: 8 */
/* last cacheline: 22 bytes */
};
$ pahole -C wl3501_md_ind drivers/net/wireless/wl3501_cs.o
struct wl3501_md_ind {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 routing; /* 3 1 */
u16 data; /* 4 2 */
u16 size; /* 6 2 */
u8 reception; /* 8 1 */
u8 pri; /* 9 1 */
u8 service_class; /* 10 1 */
struct {
u8 daddr[6]; /* 11 6 */
u8 saddr[6]; /* 17 6 */
} addr; /* 11 12 */
/* size: 24, cachelines: 1, members: 9 */
/* padding: 1 */
/* last cacheline: 24 bytes */
};
The problem is that the original code is trying to copy data into a
couple of arrays adjacent to each other in a single call to memcpy().
Now that a new struct _addr_ enclosing those two adjacent arrays
is introduced, memcpy() doesn't overrun the length of &sig.daddr[0]
and &sig.daddr, because the address of the new struct object _addr_
is used, instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/d260fe56aed7112bff2be5b4d152d03ad7b78e78.1618442265.git.gustavoars@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48a5494d6a ]
If we (for example) have a trans_cfg entry in the PCI IDs table,
but then don't find a full cfg entry for it in the info table,
we fall through to the code that treats the PCI ID table entry
as a full cfg entry. This obviously causes crashes later, e.g.
when trying to build the firmware name string.
Avoid such crashes by using the low bit of the pointer as a tag
for trans_cfg entries (automatically using a macro that checks
the type when assigning) and then checking that before trying to
use the data as a full entry - if it's just a partial entry at
that point, fail.
Since we're adding some macro magic, also check that the type is
in fact either struct iwl_cfg_trans_params or struct iwl_cfg,
failing compilation ("initializer element is not constant") if
it isn't.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.6f69fe6e4128.I921d4ae20ef5276716baeeeda0b001cf25b9b968@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a226ccd04c ]
Fix incorrect txpower init value for TSSI off chips which causes
too small txpower.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b36cc6b39 ]
When operating two VAP on a MT7610 with encryption (PSK2, SAE, OWE),
only the first one to be created will transmit properly encrypteded
frames.
All subsequently created VAPs will sent out frames with the payload left
unencrypted, breaking multicast traffic (ICMP6 NDP) and potentially
disclosing information to a third party.
Disable GTK offloading and encrypt these frames in software to
circumvent this issue. THis only seems to be necessary on MT7610 chips,
as MT7612 is not affected from our testing.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 858ebf446b ]
EEPROM blobs for MT7613BE radios start with (little endian) 0x7663,
which is also the PCI device ID for this device. The EEPROM is required
for the radio to work at useful power levels, otherwise only the lowest
power level is available.
Suggested-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ae7784ec2 ]
Fix power tracking issue by replacing unnecessary IQ calibration
with LC calibration.
When thermal difference exceeds limitation, let RF circuit adjsut
its characteristic to fit in current environment.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210319054218.3319-6-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ec5638559 ]
There is an issue when the Tx or Rx ring size increases using
'ethtool -L ...' where the new rings don't get the correct ITR
values because when we rebuild the VSI we don't know that some
of the rings may be new.
Fix this by looking at the original number of rings and
determining if the rings in ice_vsi_rebuild_set_coalesce()
were not present in the original rings received in
ice_vsi_rebuild_get_coalesce().
Also change the code to return an error if we can't allocate
memory for the coalesce data in ice_vsi_rebuild().
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5d5e0193e ]
Currently hns3 driver only handle the xmit skb with one level of
fraglist skb, add handling for multi level by calling hns3_tx_bd_num()
recursively when calculating bd num and calling hns3_fill_skb_to_desc()
recursively when filling tx desc.
When the skb has a fraglist level of 24, the skb is simply dropped and
stats.max_recursion_level is added to record the error. Move the stat
handling from hns3_nic_net_xmit() to hns3_nic_maybe_stop_tx() in order
to handle different error stat and add the 'max_recursion_level' and
'hw_limitation' stat.
Note that the max recursive level as 24 is chose according to below:
commit 48a1df6533 ("skbuff: return -EMSGSIZE in skb_to_sgvec to
prevent overflow").
And that we are not able to find a testcase to verify the recursive
fraglist case, so Fixes tag is not provided.
Reported-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2ee6fd28a ]
The array size of bd_num_list is a fixed value, it may have potential
overflow risk when array size of hclge_dfx_bd_offset_list is greater
than that fixed value. So modify bd_num_list as a pointer and allocate
memory for it according to array size of hclge_dfx_bd_offset_list.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e127906b68 ]
Commit eaf4fac478 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver. This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.
(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 991b265460 ]
Commit e20f0dbf20 ("net/mlx5e: RX, Add a prefetch command for small
L1_CACHE_BYTES") switched to using net_prefetchw at all places in mlx5e.
In the same time frame, commit 5af75c747e ("net/mlx5e: Enhanced TX
MPWQE for SKBs") added one more usage of prefetchw. When these two
changes were merged, this new occurrence of prefetchw wasn't replaced
with net_prefetchw.
This commit fixes this last occurrence of prefetchw in
mlx5e_tx_mpwqe_session_start, making the same change that was done in
mlx5e_xdp_mpwqe_session_start.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d72e7c767 ]
In emac_mac_tx_buf_send, it calls emac_tx_fill_tpd(..,skb,..).
If some error happens in emac_tx_fill_tpd(), the skb will be freed via
dev_kfree_skb(skb) in error branch of emac_tx_fill_tpd().
But the freed skb is still used via skb->len by netdev_sent_queue(,skb->len).
As i observed that emac_tx_fill_tpd() haven't modified the value of skb->len,
thus my patch assigns skb->len to 'len' before the possible free and
use 'len' instead of skb->len later.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbd6f0a948 ]
In bnxt_rx_pkt(), the RX buffers are expected to complete in order.
If the RX consumer index indicates an out of order buffer completion,
it means we are hitting a hardware bug and the driver will abort all
remaining RX packets and reset the RX ring. The RX consumer index
that we pass to bnxt_discard_rx() is not correct. We should be
passing the current index (tmp_raw_cons) instead of the old index
(raw_cons). This bug can cause us to be at the wrong index when
trying to abort the next RX packet. It can crash like this:
#0 [ffff9bbcdf5c39a8] machine_kexec at ffffffff9b05e007
#1 [ffff9bbcdf5c3a00] __crash_kexec at ffffffff9b111232
#2 [ffff9bbcdf5c3ad0] panic at ffffffff9b07d61e
#3 [ffff9bbcdf5c3b50] oops_end at ffffffff9b030978
#4 [ffff9bbcdf5c3b78] no_context at ffffffff9b06aaf0
#5 [ffff9bbcdf5c3bd8] __bad_area_nosemaphore at ffffffff9b06ae2e
#6 [ffff9bbcdf5c3c28] bad_area_nosemaphore at ffffffff9b06af24
#7 [ffff9bbcdf5c3c38] __do_page_fault at ffffffff9b06b67e
#8 [ffff9bbcdf5c3cb0] do_page_fault at ffffffff9b06bb12
#9 [ffff9bbcdf5c3ce0] page_fault at ffffffff9bc015c5
[exception RIP: bnxt_rx_pkt+237]
RIP: ffffffffc0259cdd RSP: ffff9bbcdf5c3d98 RFLAGS: 00010213
RAX: 000000005dd8097f RBX: ffff9ba4cb11b7e0 RCX: ffffa923cf6e9000
RDX: 0000000000000fff RSI: 0000000000000627 RDI: 0000000000001000
RBP: ffff9bbcdf5c3e60 R8: 0000000000420003 R9: 000000000000020d
R10: ffffa923cf6ec138 R11: ffff9bbcdf5c3e83 R12: ffff9ba4d6f928c0
R13: ffff9ba4cac28080 R14: ffff9ba4cb11b7f0 R15: ffff9ba4d5a30000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
Fixes: a1b0e4e684 ("bnxt_en: Improve RX consumer index validity check.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d13f048dd4 ]
Modify the header size check in geneve6_xmit_skb and geneve_xmit_skb
to use pskb_inet_may_pull rather than pskb_network_may_pull. This fixes
two kernel selftest failures introduced by the commit introducing the
checks:
IPv4 over geneve6: PMTU exceptions
IPv4 over geneve6: PMTU exceptions - nexthop objects
It does this by correctly accounting for the fact that IPv4 packets may
transit over geneve IPv6 tunnels (and vice versa), and still fixes the
uninit-value bug fixed by the original commit.
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: 6628ddfec7 ("net: geneve: check skb is large enough for IPv4/IPv6 header")
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27537929f3 ]
The problem is that bnxt_show_temp() returns long but "rc" is an int
and "len" is a u32. With ternary operations the type promotion is quite
tricky. The negative "rc" is first promoted to u32 and then to long so
it ends up being a high positive value instead of a a negative as we
intended.
Fix this by removing the ternary.
Fixes: d69753fa1e ("bnxt_en: return proper error codes in bnxt_show_temp")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74c97ea3b6 ]
A link time bug that I had fixed before has come back now that
another sub-module was added to the enetc driver:
ERROR: modpost: "enetc_ierb_register_pf" [drivers/net/ethernet/freescale/enetc/fsl-enetc.ko] undefined!
The problem is that the enetc Makefile is not actually used for
the ierb module if that is the only built-in driver in there
and everything else is a loadable module.
Fix it by always entering the directory this time, regardless
of which symbols are configured. This should reliably fix the
problem and prevent it from coming back another time.
Fixes: 112463ddbe ("net: dsa: felix: fix link error")
Fixes: e7d48e5fbf ("net: enetc: add a mini driver for the Integrated Endpoint Register Block")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7679c55a7 ]
Changing downshift params without software reset has no effect,
so call genphy_soft_reset() after change downshift params.
As the datasheet says:
Changes to these bits are disruptive to the normal operation therefore,
any changes to these registers must be followed by software reset
to take effect.
Fixes: 5c6bc5199b ("net: phy: marvell: add downshift support for M88E1111")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 990875b299 ]
Changing downshift params without software reset has no effect,
so call genphy_soft_reset() after change downshift params.
As the datasheet says:
Changes to these bits are disruptive to the normal operation therefore,
any changes to these registers must be followed by software reset
to take effect.
Fixes: 911af5e149 ("net: phy: marvell: fix downshift function naming")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9a4c080de ]
The size of the buffer than can be written to is currently incorrect, it is
always the size of the entire buffer even though the snprintf is writing
as position pos into the buffer. Fix this by setting the buffer size to be
the number of bytes left in the buffer, namely sizeof(buf) - pos.
Addresses-Coverity: ("Out-of-bounds access")
Fixes: 7b0e2c4f6b ("wlcore: fix overlapping snprintf arguments in debugfs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419141405.180582-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaaf52e4b8 ]
ath10k_wmi_tlv_op_pull_peer_stats_info() could try to unlock RCU lock
winthout locking it first when peer reason doesn't match the valid
cases for this function.
Add a default case to return without unlocking.
Fixes: 09078368d5 ("ath10k: hold RCU lock when calling ieee80211_find_sta_by_ifaddr()")
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210406230228.31301-1-skhan@linuxfoundation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8392df5d7e ]
In ath10k_htc_send_bundle, the bundle_skb could be freed by
dev_kfree_skb_any(bundle_skb). But the bundle_skb is used later
by bundle_skb->len.
As skb_len = bundle_skb->len, my patch replaces bundle_skb->len to
skb_len after the bundle_skb was freed.
Fixes: c8334512f3 ("ath10k: add htt TX bundle for sdio")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210329120154.8963-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dd9a40fd6 ]
When the error check in ath9k_hw_read_revisions() was added, it checked for
-EIO which is what ath9k_regread() in the ath9k_htc driver uses. However,
for plain ath9k, the register read function uses ioread32(), which just
returns -1 on error. So if such a read fails, it still gets passed through
and ends up as a weird mac revision in the log output.
Fix this by changing ath9k_regread() to return -1 on error like ioread32()
does, and fix the error check to look for that instead of -EIO.
Fixes: 2f90c7e5d0 ("ath9k: Check for errors when reading SREV register")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210326180819.142480-1-toke@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 357a07c266 ]
The Intel xway phys offer the possibility to deactivate the integrated
LED function and to control the LEDs manually.
If this was set by the bootloader, it must be ensured that the
integrated LED function is enabled for all LEDs when loading the driver.
Before commit 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
the LEDs were enabled by a soft-reset of the PHY (using
genphy_soft_reset). Initialize the XWAY_MDIO_LED with it's default
value (which is applied during a soft reset) instead of adding back
the soft reset. This brings back the default LED configuration while
still preventing an excessive amount of soft resets.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5718458b09 ]
When a lot of frames were received in the short term, the driver
caused a stuck of receiving until a new frame was received. For example,
the following command from other device could cause this issue.
$ sudo ping -f -l 1000 -c 1000 <this driver's ipaddress>
The previous code always cleared the interrupt flag of RX but checks
the interrupt flags in ravb_poll(). So, ravb_poll() could not call
ravb_rx() in the next time until a new RX frame was received if
ravb_rx() returned true. To fix the issue, always calls ravb_rx()
regardless the interrupt flags condition.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e6038b88a ]
TSO and TBS cannot co-exist and current implementation requires two
fixes:
1) stmmac_open() does not need to call stmmac_enable_tbs() because
the MAC is reset in stmmac_init_dma_engine() anyway.
2) Inside stmmac_hw_setup(), we should call stmmac_enable_tso() for
TX Q that is _not_ configured for TBS.
Fixes: 579a25a854 ("net: stmmac: Initial support for TBS")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90b669d65d ]
The number of lanes of devlink port should be correctly initialized
when registering the port, so that the input check when running
"devlink port split <port> count <N>" can pass.
Fixes: a21cf0a833 ("devlink: Add a new devlink port lanes attribute and pass to netlink")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d83b8aa520 ]
The bit-masks used for the TXERRCH and RXERRCH (tx and rx error channels)
are incorrect and always lead to a zero result. The mask values are
currently the incorrect post-right shifted values, fix this by setting
them to the currect values.
(I double checked these against the TMS320TCI6482 data sheet, section
5.30, page 127 to ensure I had the correct mask values for the TXERRCH
and RXERRCH fields in the MACSTATUS register).
Addresses-Coverity: ("Operands don't affect result")
Fixes: a6286ee630 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
