[ Upstream commit bd18de5179 ]
Syzbot reports that we may be able to get into a situation where
mac80211 has pending ACK frames on shutdown with hwsim. It appears
that the reason for this is that syzbot uses the wmediumd hooks to
intercept/injection frames, and may shut down hwsim, removing the
radio(s), while frames are pending in the air simulation.
Clean out the pending queue when the interface is stopped, after
this the frames can't be reported back to mac80211 properly anyway.
Reported-by: syzbot+a063bbf0b15737362592@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20210517170429.b0f85ab0eda1.Ie42a6ec6b940c971f3441286aeaaae2fe368e29a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 419b4a142a ]
The brcmfmac driver ignores any errors on initialization with the
different busses by deferring the initialization to a workqueue and
ignoring all possible errors that might happen. Fix up all of this by
only allowing the module to load if all bus registering worked properly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-70-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30a3509476 ]
This reverts commit 42daad3343.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit here did nothing to actually help if usb_register()
failed, so it gives a "false sense of security" when there is none. The
correct solution is to correctly unwind from this error.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-69-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e79b38fe9 ]
The libertas driver was trying to register sysfs groups "by hand" which
causes them to be created _after_ the device is initialized and
announced to userspace, which causes races and can prevent userspace
tools from seeing the sysfs files correctly.
Fix this up by using the built-in sysfs_groups pointers in struct
net_device which were created for this very reason, fixing the race
condition, and properly allowing for any error that might have occured
to be handled properly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-54-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4665107776 ]
This reverts commit 434256833d.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit was incorrect, the error needs to be propagated back
to the caller AND if the second group call fails, the first needs to be
removed. There are much better ways to solve this, the driver should
NOT be calling sysfs_create_group() on its own as it is racing userspace
and loosing.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-53-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efba106f89 ]
This reverts commit fc6a652155.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The change being reverted does NOTHING as the caller to this function
does not even look at the return value of the call. So the "claim" that
this fixed an an issue is not true. It will be fixed up properly in a
future patch by propagating the error up the stack correctly.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-43-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c3944a5621 upstream.
Currently the fragment cache setup during peer assoc is
cleared only during peer delete. In case a key reinstallation
happens with the same peer, the same fragment cache with old
fragments added before key installation could be clubbed
with fragments received after. This might be exploited
to mix fragments of different data resulting in a proper
unintended reassembled packet to be passed up the stack.
Hence flush the fragment cache on every key installation to prevent
potential attacks (CVE-2020-24587).
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Cc: stable@vger.kernel.org
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.218dc777836f.I9af6fc76215a35936c4152552018afb5079c5d8c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62a8ff67eb upstream.
In certain scenarios a normal MSDU can be received as an A-MSDU when
the A-MSDU present bit of a QoS header gets flipped during reception.
Since this bit is unauthenticated, the hardware crypto engine can pass
the frame to the driver without any error indication.
This could result in processing unintended subframes collected in the
A-MSDU list. Hence, validate A-MSDU list by checking if the first frame
has a valid subframe header.
Comparing the non-aggregated MSDU and an A-MSDU, the fields of the first
subframe DA matches the LLC/SNAP header fields of a normal MSDU.
In order to avoid processing such frames, add a validation to
filter such A-MSDU frames where the first subframe header DA matches
with the LLC/SNAP header pattern.
Tested-on: QCA9984 hw1.0 PCI 10.4-3.10-00047
Cc: stable@vger.kernel.org
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.e6f5eb7b9847.I38a77ae26096862527a5eab73caebd7346af8b66@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0dc267b13f upstream.
TKIP Michael MIC was not verified properly for PCIe cases since the
validation steps in ieee80211_rx_h_michael_mic_verify() in mac80211 did
not get fully executed due to unexpected flag values in
ieee80211_rx_status.
Fix this by setting the flags property to meet mac80211 expectations for
performing Michael MIC validation there. This fixes CVE-2020-26141. It
does the same as ath10k_htt_rx_proc_rx_ind_hl() for SDIO which passed
MIC verification case. This applies only to QCA6174/QCA9377 PCIe.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.c3f1d42c6746.I795593fcaae941c471425b8c7d5f7bb185d29142@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 079a108feb upstream.
When the discard flag is set by the firmware for an MPDU, it should be
dropped. This allows a mitigation for CVE-2020-24588 to be implemented
in the firmware.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.11968c725b5c.Idd166365ebea2771c0c0a38c78b5060750f90e17@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40e7462dad upstream.
Fragmentation is not used with multicast frames. Discard unexpected
fragments with multicast DA. This fixes CVE-2020-26145.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.9ca6ca7945a9.I1e18b514590af17c155bda86699bc3a971a8dcf4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65c415a144 upstream.
Fragmentation is not used with multicast frames. Discard unexpected
fragments with multicast DA. This fixes CVE-2020-26145.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.5a0bd289bda8.Idd6ebea20038fb1cfee6de924aa595e5647c9eae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1166b2653 upstream.
PN replay check for not fragmented frames is finished in the firmware,
but this was not done for fragmented frames when ath10k is used with
QCA6174/QCA6377 PCIe. mac80211 has the function
ieee80211_rx_h_defragment() for PN replay check for fragmented frames,
but this does not get checked with QCA6174 due to the
ieee80211_has_protected() condition not matching the cleared Protected
bit case.
Validate the PN of received fragmented frames within ath10k when CCMP is
used and drop the fragment if the PN is not correct (incremented by
exactly one from the previous fragment). This applies only for
QCA6174/QCA6377 PCIe.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.9ba2664866a4.I756e47b67e210dba69966d989c4711ffc02dc6bc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30b0e0ee9d upstream.
If alloc_workqueue() fails, properly catch this and propagate the error
to the calling functions, so that the devuce initialization will
properly error out.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Bryan Brattlof <hello@bryanbrattlof.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-14-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68c5634c4a upstream.
This reverts commit 765976285a.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit is not correct, it should not have used unlikely() and is
not propagating the error properly to the calling function, so it should
be reverted at this point in time. Also, if the check failed, the
work queue was still assumed to be allocated, so further accesses would
have continued to fail, meaning this patch does nothing to solve the
root issues at all.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Bryan Brattlof <hello@bryanbrattlof.com>
Fixes: 765976285a ("rtlwifi: fix a potential NULL pointer dereference")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-13-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7909a590eb upstream.
gcc-11 with KASAN on 32-bit arm produces a warning about a function
that needs a lot of stack space:
drivers/net/wireless/cisco/airo.c: In function 'setup_card.constprop':
drivers/net/wireless/cisco/airo.c:3960:1: error: the frame size of 1512 bytes is larger than 1400 bytes [-Werror=frame-larger-than=]
Most of this is from a single large structure that could be dynamically
allocated or moved into the per-device structure. However, as the callers
all seem to have a fairly well bounded call chain, the easiest change
is to pull out the part of the function that needs the large variables
into a separate function and mark that as noinline_for_stack. This does
not reduce the total stack usage, but it gets rid of the warning and
requires minimal changes otherwise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210323131634.2669455-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 130f634da1 ]
Function qtnf_event_handle_external_auth calls memcpy without
checking the length.
A user could control that length and trigger a buffer overflow.
Fix by checking the length is within the maximum allowed size.
Signed-off-by: Lee Gibson <leegib@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419145842.345787-1-leegib@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb43e5718d ]
Fix the following out-of-bounds warnings by adding a new structure
wl3501_req instead of duplicating the same members in structure
wl3501_join_req and wl3501_scan_confirm:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [39, 108] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 36 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [25, 95] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 22 [-Warray-bounds]
Refactor the code, accordingly:
$ pahole -C wl3501_req drivers/net/wireless/wl3501_cs.o
struct wl3501_req {
u16 beacon_period; /* 0 2 */
u16 dtim_period; /* 2 2 */
u16 cap_info; /* 4 2 */
u8 bss_type; /* 6 1 */
u8 bssid[6]; /* 7 6 */
struct iw_mgmt_essid_pset ssid; /* 13 34 */
struct iw_mgmt_ds_pset ds_pset; /* 47 3 */
struct iw_mgmt_cf_pset cf_pset; /* 50 8 */
struct iw_mgmt_ibss_pset ibss_pset; /* 58 4 */
struct iw_mgmt_data_rset bss_basic_rset; /* 62 10 */
/* size: 72, cachelines: 2, members: 10 */
/* last cacheline: 8 bytes */
};
$ pahole -C wl3501_join_req drivers/net/wireless/wl3501_cs.o
struct wl3501_join_req {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 reserved; /* 3 1 */
struct iw_mgmt_data_rset operational_rset; /* 4 10 */
u16 reserved2; /* 14 2 */
u16 timeout; /* 16 2 */
u16 probe_delay; /* 18 2 */
u8 timestamp[8]; /* 20 8 */
u8 local_time[8]; /* 28 8 */
struct wl3501_req req; /* 36 72 */
/* size: 108, cachelines: 2, members: 10 */
/* last cacheline: 44 bytes */
};
$ pahole -C wl3501_scan_confirm drivers/net/wireless/wl3501_cs.o
struct wl3501_scan_confirm {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 reserved; /* 3 1 */
u16 status; /* 4 2 */
char timestamp[8]; /* 6 8 */
char localtime[8]; /* 14 8 */
struct wl3501_req req; /* 22 72 */
/* --- cacheline 1 boundary (64 bytes) was 30 bytes ago --- */
u8 rssi; /* 94 1 */
/* size: 96, cachelines: 2, members: 8 */
/* padding: 1 */
/* last cacheline: 32 bytes */
};
The problem is that the original code is trying to copy data into a
bunch of struct members adjacent to each other in a single call to
memcpy(). Now that a new struct wl3501_req enclosing all those adjacent
members is introduced, memcpy() doesn't overrun the length of
&sig.beacon_period and &this->bss_set[i].beacon_period, because the
address of the new struct object _req_ is used as the destination,
instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1fbaf516da763b50edac47d792a9145aa4482e29.1618442265.git.gustavoars@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820aa37638 ]
Fix the following out-of-bounds warnings by enclosing structure members
daddr and saddr into new struct addr, in structures wl3501_md_req and
wl3501_md_ind:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
Refactor the code, accordingly:
$ pahole -C wl3501_md_req drivers/net/wireless/wl3501_cs.o
struct wl3501_md_req {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 routing; /* 3 1 */
u16 data; /* 4 2 */
u16 size; /* 6 2 */
u8 pri; /* 8 1 */
u8 service_class; /* 9 1 */
struct {
u8 daddr[6]; /* 10 6 */
u8 saddr[6]; /* 16 6 */
} addr; /* 10 12 */
/* size: 22, cachelines: 1, members: 8 */
/* last cacheline: 22 bytes */
};
$ pahole -C wl3501_md_ind drivers/net/wireless/wl3501_cs.o
struct wl3501_md_ind {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 routing; /* 3 1 */
u16 data; /* 4 2 */
u16 size; /* 6 2 */
u8 reception; /* 8 1 */
u8 pri; /* 9 1 */
u8 service_class; /* 10 1 */
struct {
u8 daddr[6]; /* 11 6 */
u8 saddr[6]; /* 17 6 */
} addr; /* 11 12 */
/* size: 24, cachelines: 1, members: 9 */
/* padding: 1 */
/* last cacheline: 24 bytes */
};
The problem is that the original code is trying to copy data into a
couple of arrays adjacent to each other in a single call to memcpy().
Now that a new struct _addr_ enclosing those two adjacent arrays
is introduced, memcpy() doesn't overrun the length of &sig.daddr[0]
and &sig.daddr, because the address of the new struct object _addr_
is used, instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/d260fe56aed7112bff2be5b4d152d03ad7b78e78.1618442265.git.gustavoars@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48a5494d6a ]
If we (for example) have a trans_cfg entry in the PCI IDs table,
but then don't find a full cfg entry for it in the info table,
we fall through to the code that treats the PCI ID table entry
as a full cfg entry. This obviously causes crashes later, e.g.
when trying to build the firmware name string.
Avoid such crashes by using the low bit of the pointer as a tag
for trans_cfg entries (automatically using a macro that checks
the type when assigning) and then checking that before trying to
use the data as a full entry - if it's just a partial entry at
that point, fail.
Since we're adding some macro magic, also check that the type is
in fact either struct iwl_cfg_trans_params or struct iwl_cfg,
failing compilation ("initializer element is not constant") if
it isn't.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.6f69fe6e4128.I921d4ae20ef5276716baeeeda0b001cf25b9b968@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a226ccd04c ]
Fix incorrect txpower init value for TSSI off chips which causes
too small txpower.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b36cc6b39 ]
When operating two VAP on a MT7610 with encryption (PSK2, SAE, OWE),
only the first one to be created will transmit properly encrypteded
frames.
All subsequently created VAPs will sent out frames with the payload left
unencrypted, breaking multicast traffic (ICMP6 NDP) and potentially
disclosing information to a third party.
Disable GTK offloading and encrypt these frames in software to
circumvent this issue. THis only seems to be necessary on MT7610 chips,
as MT7612 is not affected from our testing.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 858ebf446b ]
EEPROM blobs for MT7613BE radios start with (little endian) 0x7663,
which is also the PCI device ID for this device. The EEPROM is required
for the radio to work at useful power levels, otherwise only the lowest
power level is available.
Suggested-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ae7784ec2 ]
Fix power tracking issue by replacing unnecessary IQ calibration
with LC calibration.
When thermal difference exceeds limitation, let RF circuit adjsut
its characteristic to fit in current environment.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210319054218.3319-6-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9a4c080de ]
The size of the buffer than can be written to is currently incorrect, it is
always the size of the entire buffer even though the snprintf is writing
as position pos into the buffer. Fix this by setting the buffer size to be
the number of bytes left in the buffer, namely sizeof(buf) - pos.
Addresses-Coverity: ("Out-of-bounds access")
Fixes: 7b0e2c4f6b ("wlcore: fix overlapping snprintf arguments in debugfs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419141405.180582-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaaf52e4b8 ]
ath10k_wmi_tlv_op_pull_peer_stats_info() could try to unlock RCU lock
winthout locking it first when peer reason doesn't match the valid
cases for this function.
Add a default case to return without unlocking.
Fixes: 09078368d5 ("ath10k: hold RCU lock when calling ieee80211_find_sta_by_ifaddr()")
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210406230228.31301-1-skhan@linuxfoundation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8392df5d7e ]
In ath10k_htc_send_bundle, the bundle_skb could be freed by
dev_kfree_skb_any(bundle_skb). But the bundle_skb is used later
by bundle_skb->len.
As skb_len = bundle_skb->len, my patch replaces bundle_skb->len to
skb_len after the bundle_skb was freed.
Fixes: c8334512f3 ("ath10k: add htt TX bundle for sdio")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210329120154.8963-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dd9a40fd6 ]
When the error check in ath9k_hw_read_revisions() was added, it checked for
-EIO which is what ath9k_regread() in the ath9k_htc driver uses. However,
for plain ath9k, the register read function uses ioread32(), which just
returns -1 on error. So if such a read fails, it still gets passed through
and ends up as a weird mac revision in the log output.
Fix this by changing ath9k_regread() to return -1 on error like ioread32()
does, and fix the error check to look for that instead of -EIO.
Fixes: 2f90c7e5d0 ("ath9k: Check for errors when reading SREV register")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210326180819.142480-1-toke@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8e083ee8e ]
In mwl8k_probe_hw, hw->priv->txq is freed at the first time by
dma_free_coherent() in the call chain:
if(!priv->ap_fw)->mwl8k_init_txqs(hw)->mwl8k_txq_init(hw, i).
Then in err_free_queues of mwl8k_probe_hw, hw->priv->txq is freed
at the second time by mwl8k_txq_deinit(hw, i)->dma_free_coherent().
My patch set txq->txd to NULL after the first free to avoid the
double free.
Fixes: a66098daac ("mwl8k: Marvell TOPDOG wireless driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210402182627.4256-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b0e2c4f6b ]
gcc complains about undefined behavior in calling snprintf()
with the same buffer as input and output:
drivers/net/wireless/ti/wl18xx/debugfs.c: In function 'diversity_num_of_packets_per_ant_read':
drivers/net/wireless/ti/wl18xx/../wlcore/debugfs.h:86:3: error: 'snprintf' argument 4 overlaps destination object 'buf' [-Werror=restrict]
86 | snprintf(buf, sizeof(buf), "%s[%d] = %d\n", \
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
87 | buf, i, stats->sub.name[i]); \
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ti/wl18xx/debugfs.c:24:2: note: in expansion of macro 'DEBUGFS_FWSTATS_FILE_ARRAY'
24 | DEBUGFS_FWSTATS_FILE_ARRAY(a, b, c, wl18xx_acx_statistics)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ti/wl18xx/debugfs.c:159:1: note: in expansion of macro 'WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY'
159 | WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY(diversity, num_of_packets_per_ant,
There are probably other ways of handling the debugfs file, without
using on-stack buffers, but a simple workaround here is to remember the
current position in the buffer and just keep printing in there.
Fixes: bcca1bbdd4 ("wlcore: add debugfs macro to help print fw statistics arrays")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210323125723.1961432-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18fb0bedb5 ]
The signal strength of 5G is quite low, so user can't connect to an AP far
away. New parameters with new format and its parser are updated by the commit
84d26fda52 ("rtlwifi: Update 8821ae new phy parameters and its parser."), but
some parameters are missing. Use this commit to update to the novel parameters
that use new format.
Fixes: 84d26fda52 ("rtlwifi: Update 8821ae new phy parameters and its parser")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210219052607.7323-1-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45247a8561 ]
Use the additional memory barrier to ensure the skb list up-to-date
between the skb producer and consumer to avoid the invalid skb content
written into sdio controller and then cause device hang due to mcu assert
caught by WR_TIMEOUT_INT.
Fixes: 1522ff731f ("mt76: mt7663s: introduce sdio tx aggregation")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 455ae5aabc ]
Each packet should be padded with the additional zero to become 4-bytes
alignment in sdio tx aggregation.
Fixes: 1522ff731f ("mt76: mt7663s: introduce sdio tx aggregation")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b35050a32 ]
In order to properly report MIB counters to mac80211, resets stats in
mt7915_get_stats routine() and hold mt76 mutex accessing MIB counters.
Sum up MIB counters in mt7915_mac_update_mib_stats routine.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eb6f6c437 ]
In order to properly report MIB counters to mac80211, resets stats in
mt7615_get_stats routine and hold mt76 mutex accessing MIB counters.
Sum up MIB counters in mt7615_mac_update_mib_stats routine.
Fixes: c388d8584b ("mt76: mt7615: add a get_stats() callback")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dcf3c04f0 ]
The first pointer in the txp needs to be unmapped as well, otherwise it will
leak DMA mapping entries
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: 27d5c528a7 ("mt76: fix double DMA unmap of the first buffer on 7615/7915")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebee7885bb ]
The first pointer in the txp needs to be unmapped as well, otherwise it will
leak DMA mapping entries
Fixes: 27d5c528a7 ("mt76: fix double DMA unmap of the first buffer on 7615/7915")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87fce88658 ]
Currently the expression ~nic_conf1 is always true because nic_conf1
is a u16 and according to 6.5.3.3 of the C standard the ~ operator
promotes the u16 to an integer before flipping all the bits. Thus
the top 16 bits of the integer result are all set so the expression
is always true. If the intention was to flip all the bits of nic_conf1
then casting the integer result back to a u16 is a suitabel fix.
Interestingly static analyzers seem to thing a bitwise ! should be
used instead of ~ for this scenario, so I think the original intent
of the expression may need some extra consideration.
Addresses-Coverity: ("Logical vs. bitwise operator")
Fixes: c869f77d6a ("add mt7601u driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210225183241.1002129-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9eaee0c2e ]
The sscanf() function returns the number of matches (0 or 1 in this
case). It doesn't return error codes. We should return -EINVAL if the
string is invalid
Fixes: c376c1fc87 ("rtw88: add h2c command in debugfs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YE8nmatMDBDDWkjq@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b4403cee64 upstream.
With buf uninitialized in mt76_dma_tx_queue_skb_raw, its field skip_unmap
could potentially inherit a non-zero value from stack garbage.
If this happens, it will cause DMA mappings for MCU command frames to not be
unmapped after completion
Fixes: 27d5c528a7 ("mt76: fix double DMA unmap of the first buffer on 7615/7915")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ff25985ea upstream.
Using a kernel with the Undefined Behaviour Sanity Checker (UBSAN) enabled, the
following array overrun is logged:
================================================================================
UBSAN: array-index-out-of-bounds in /home/finger/wireless-drivers-next/drivers/net/wireless/realtek/rtw88/phy.c:1789:34
index 5 is out of range for type 'u8 [5]'
CPU: 2 PID: 84 Comm: kworker/u16:3 Tainted: G O 5.12.0-rc5-00086-gd88bba47038e-dirty #651
Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.50 09/29/2014
Workqueue: phy0 ieee80211_scan_work [mac80211]
Call Trace:
dump_stack+0x64/0x7c
ubsan_epilogue+0x5/0x40
__ubsan_handle_out_of_bounds.cold+0x43/0x48
rtw_get_tx_power_params+0x83a/drivers/net/wireless/realtek/rtw88/0xad0 [rtw_core]
? rtw_pci_read16+0x20/0x20 [rtw_pci]
? check_hw_ready+0x50/0x90 [rtw_core]
rtw_phy_get_tx_power_index+0x4d/0xd0 [rtw_core]
rtw_phy_set_tx_power_level+0xee/0x1b0 [rtw_core]
rtw_set_channel+0xab/0x110 [rtw_core]
rtw_ops_config+0x87/0xc0 [rtw_core]
ieee80211_hw_config+0x9d/0x130 [mac80211]
ieee80211_scan_state_set_channel+0x81/0x170 [mac80211]
ieee80211_scan_work+0x19f/0x2a0 [mac80211]
process_one_work+0x1dd/0x3a0
worker_thread+0x49/0x330
? rescuer_thread+0x3a0/0x3a0
kthread+0x134/0x150
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x22/0x30
================================================================================
The statement where an array is being overrun is shown in the following snippet:
if (rate <= DESC_RATE11M)
tx_power = pwr_idx_2g->cck_base[group];
else
====> tx_power = pwr_idx_2g->bw40_base[group];
The associated arrays are defined in main.h as follows:
struct rtw_2g_txpwr_idx {
u8 cck_base[6];
u8 bw40_base[5];
struct rtw_2g_1s_pwr_idx_diff ht_1s_diff;
struct rtw_2g_ns_pwr_idx_diff ht_2s_diff;
struct rtw_2g_ns_pwr_idx_diff ht_3s_diff;
struct rtw_2g_ns_pwr_idx_diff ht_4s_diff;
};
The problem arises because the value of group is 5 for channel 14. The trivial
increase in the dimension of bw40_base fails as this struct must match the layout of
efuse. The fix is to add the rate as an argument to rtw_get_channel_group() and set
the group for channel 14 to 4 if rate <= DESC_RATE11M.
This patch fixes commit fa6dfe6bff ("rtw88: resolve order of tx power setting routines")
Fixes: fa6dfe6bff ("rtw88: resolve order of tx power setting routines")
Reported-by: Богдан Пилипенко <bogdan.pylypenko107@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210401192717.28927-1-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 260a9ad944 upstream.
The "ext->key_len" is a u16 that comes from the user. If it's over
SCM_KEY_LEN (32) that could lead to memory corruption.
Fixes: e0d369d1d9 ("[PATCH] ieee82011: Added WE-18 support to default wireless extension handler")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YHaoA1i+8uT4ir4h@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06991d1f73 upstream.
We should use ieee80211_free_txskb() to report skb status avoid wrong
aql accounting after reset.
Cc: stable@vger.kernel.org
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c434e5e48d upstream.
The rsi_resume() does access the bus to enable interrupts on the RSI
SDIO WiFi card, however when calling sdio_claim_host() in the resume
path, it is possible the bus is already claimed and sdio_claim_host()
spins indefinitelly. Enable the SDIO card interrupts in resume_noirq
instead to prevent anything else from claiming the SDIO bus first.
Fixes: 20db073327 ("rsi: sdio suspend and resume support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210327235932.175896-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
