[ Upstream commit 8f4e3d48bb ]
A patch from 2017 changed some accesses to DMA memory to use
get_unaligned_le32() and similar interfaces, to avoid problems
with doing unaligned accesson uncached memory.
However, the change in the mwifiex_pcie_alloc_sleep_cookie_buf()
function ended up changing the size of the access instead,
as it operates on a pointer to u8.
Change this function back to actually access the entire 32 bits.
Note that the pointer is aligned by definition because it came
from dma_alloc_coherent().
Fixes: 92c70a958b ("mwifiex: fix for unaligned reads")
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be7f62eeba ]
priv->cbs is an array of priv->info->num_cbs_shapers elements of type
struct sja1105_cbs_entry which only get allocated if CONFIG_NET_SCH_CBS
is enabled.
However, sja1105_reload_cbs() is called from sja1105_static_config_reload()
which in turn is called for any of the items in sja1105_reset_reasons,
therefore during the normal runtime of the driver and not just from a
code path which can be triggered by the tc-cbs offload.
The sja1105_reload_cbs() function does not contain a check whether the
priv->cbs array is NULL or not, it just assumes it isn't and proceeds to
iterate through the credit-based shaper elements. This leads to a NULL
pointer dereference.
The solution is to return success if the priv->cbs array has not been
allocated, since sja1105_reload_cbs() has nothing to do.
Fixes: 4d7525085a ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e7256f12c ]
Complete to commit def4ec6dce ("e1000e: PCIm function state support")
Check the PCIm state only on CSME systems. There is no point to do this
check on non CSME systems.
This patch fixes a generation a false-positive warning:
"Error in exiting dmoff"
Fixes: def4ec6dce ("e1000e: PCIm function state support")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d67fb4772d ]
The key length used to store the macsec key was set to MACSEC_KEYID_LEN
(16), which is an issue as:
- This was never meant to be the key length.
- The key length can be > 16.
Fix this by using MACSEC_MAX_KEY_LEN instead (the max length accepted in
uAPI).
Fixes: 27736563ce ("net: atlantic: MACSec egress offload implementation")
Fixes: 9ff40a751a ("net: atlantic: MACSec ingress offload implementation")
Reported-by: Lior Nahmanson <liorna@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c309217f91 ]
The key length used to store the macsec key was set to MACSEC_KEYID_LEN
(16), which is an issue as:
- This was never meant to be the key length.
- The key length can be > 16.
Fix this by using MACSEC_MAX_KEY_LEN instead (the max length accepted in
uAPI).
Fixes: 28c5107aa9 ("net: phy: mscc: macsec support")
Reported-by: Lior Nahmanson <liorna@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f7fe51211 ]
The key length used when offloading macsec to Ethernet or PHY drivers
was set to MACSEC_KEYID_LEN (16), which is an issue as:
- This was never meant to be the key length.
- The key length can be > 16.
Fix this by using MACSEC_MAX_KEY_LEN to store the key (the max length
accepted in uAPI) and secy->key_len to copy it.
Fixes: 3cf3227a21 ("net: macsec: hardware offloading infrastructure")
Reported-by: Lior Nahmanson <liorna@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6ebca8efa ]
Free tx_pool and clear it, if allocation of tso_pool fails.
release_tx_pools() assumes we have both tx and tso_pools if ->tx_pool is
non-NULL. If allocation of tso_pool fails in init_tx_pools(), the assumption
will not be true and we would end up dereferencing ->tx_buff, ->free_map
fields from a NULL pointer.
Fixes: 3205306c6b ("ibmvnic: Update TX pool initialization routine")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 552a33729f ]
free_long_term_buff() checks ltb->buff to decide whether we have a long
term buffer to free. So set ltb->buff to NULL afer freeing. While here,
also clear ->map_id, fix up some coding style and log an error.
Fixes: 9c4eaabd1b ("Check CRQ command return codes")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72368f8b2b ]
This fixes a crash in replenish_rx_pool() when called from ibmvnic_poll()
after a previous call to replenish_rx_pool() encountered an error when
allocating a socket buffer.
Thanks to Rick Lindsley and Dany Madden for helping debug the crash.
Fixes: 4f0b6812e9 ("ibmvnic: Introduce batched RX buffer descriptor transmission")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65d6470d13 ]
We batch subordinate command response queue (scrq) descriptors that we
need to send to the VIOS using an "indirect" buffer. If after we queue
one or more scrqs in the indirect buffer encounter an error (say fail
to allocate an skb), we leave the queued scrq descriptors in the
indirect buffer until the next call to ibmvnic_xmit().
On the next call to ibmvnic_xmit(), it is possible that the adapter is
going through a reset and it is possible that the long term buffers
have been unmapped on the VIOS side. If we proceed to flush (send) the
packets that are in the indirect buffer, we will end up using the old
map ids and this can cause the VIOS to trigger an unnecessary FATAL
error reset.
Instead of flushing packets remaining on the indirect_buff, discard
(clean) them instead.
Fixes: 0d97338818 ("ibmvnic: Introduce xmit_more support using batched subCRQ hcalls")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ca220f928 ]
This reverts commit 7c451f3ef6.
When a vnic interface is taken down and then up, connectivity is not
restored. We bisected it to this commit. Reverting this commit until
we can fully investigate the issue/benefit of the change.
Fixes: 7c451f3ef6 ("ibmvnic: remove duplicate napi_schedule call in open function")
Reported-by: Cristobal Forno <cforno12@linux.ibm.com>
Reported-by: Abdul Haleem <abdhalee@in.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ec13aff05 ]
This reverts commit 1c7d45e7b2.
We tried to optimize the number of hcalls we send and skipped sending
the REQUEST_MAP calls for some maps. However during resets, we need to
resend all the maps to the VIOS since the VIOS does not remember the
old values. In fact we may have failed over to a new VIOS which will
not have any of the mappings.
When we send packets with map ids the VIOS does not know about, it
triggers a FATAL reset. While the client does recover from the FATAL
error reset, we are seeing a large number of such resets. Handling
FATAL resets is lot more unnecessary work than issuing a few more
hcalls so revert the commit and resend the maps to the VIOS.
Fixes: 1c7d45e7b2 ("ibmvnic: simplify reset_long_term_buff function")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 956e759d5f ]
A recent change that made i40e use new udp_tunnel infrastructure
uses a method that expects to be called under rtnl lock.
However, not all codepaths do the lock prior to calling
i40e_setup_pf_switch.
Fix that by adding additional rtnl locking and unlocking.
Fixes: 40a98cb6f0 ("i40e: convert to new udp_tunnel infrastructure")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9262793e59 ]
Disabling autonegotiation was allowed only for 10GBaseT PHY.
The condition was changed to check if link media type is BaseT.
Fixes: 3ce12ee9d8 ("i40e: Fix order of checks when enabling/disabling autoneg in ethtool")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Karen Sornek <karen.sornek@intel.com>
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c04cfcd4a ]
When vsi->type == I40E_VSI_FDIR, we have caught the return value of
i40e_vsi_request_irq() but without further handling. Check and execute
memory clean on failure just like the other i40e_vsi_request_irq().
Fixes: 8a9eb7d3cb ("i40e: rework fdir setup and teardown")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2ac9800cf ]
The Broadcom UniMAC MDIO bus from mdio-bcm-unimac module comes too late.
So, GENET cannot find the ethernet PHY on UniMAC MDIO bus. This leads
GENET fail to attach the PHY as following log:
bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
...
could not attach to PHY
bcmgenet fd580000.ethernet eth0: failed to connect to PHY
uart-pl011 fe201000.serial: no DMA platform data
libphy: bcmgenet MII bus: probed
...
unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
This patch adds the soft dependency to load mdio-bcm-unimac module
before genet module to avoid the issue.
Fixes: 9a4e796970 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=213485
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0303b30375 ]
Both MAC802154_HWSIM_ATTR_RADIO_ID and MAC802154_HWSIM_ATTR_RADIO_EDGE
must be present to avoid a crash.
Fixes: f25da51fdc ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@datenfreihafen.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210621180244.882076-1-eric.dumazet@gmail.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28a5501c33 ]
No matter from hwsim_remove or hwsim_del_radio_nl, hwsim_del fails to
remove the entry in the edges list. Take the example below, phy0, phy1
and e0 will be deleted, resulting in e1 not freed and accessed in the
future.
hwsim_phys
|
------------------------------
| |
phy0 (edges) phy1 (edges)
----> e1 (idx = 1) ----> e0 (idx = 0)
Fix this by deleting and freeing all the entries in the edges list
between hwsim_edge_unsubscribe_me and list_del(&phy->list).
Reported-by: syzbot+b80c9959009a9325cdff@syzkaller.appspotmail.com
Fixes: 1c9f4a3fce ("ieee802154: hwsim: fix rcu handling")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210616020901.2759466-1-mudongliangabcd@gmail.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce8eb4c728 ]
When changing number of TX queues using ethtool:
# ethtool -L eth0 tx 1
[ 135.301047] Unable to handle kernel paging request at virtual address 00000000af5d0000
[...]
[ 135.525128] Call trace:
[ 135.525142] dma_release_from_dev_coherent+0x2c/0xb0
[ 135.525148] dma_free_attrs+0x54/0xe0
[ 135.525156] k3_cppi_desc_pool_destroy+0x50/0xa0
[ 135.525164] am65_cpsw_nuss_remove_tx_chns+0x88/0xdc
[ 135.525171] am65_cpsw_set_channels+0x3c/0x70
[...]
This is because k3_cppi_desc_pool_destroy() which is called after
k3_udma_glue_release_tx_chn() in am65_cpsw_nuss_remove_tx_chns()
references struct device that is unregistered at the end of
k3_udma_glue_release_tx_chn()
Therefore the right order is to call k3_cppi_desc_pool_destroy() and
destroy desc pool before calling k3_udma_glue_release_tx_chn().
Fix this throughout the driver.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddeacc4f64 ]
Resetting software indexes in bcm4908_dma_alloc_buf_descs() is not
enough as it's called during device probe only. Driver resets DMA on
every .ndo_open callback and it's required to reset indexes then.
This fixes inconsistent rings state and stalled traffic after interface
down & up sequence.
Fixes: 4feffeadbc ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05684fd583 ]
Before this patch, we use value from 2 seconds ago to decide
whether we should do lc calibration.
Although this don't happen frequently, fix flow to the way it should be.
Fixes: 7ae7784ec2 ("rtw88: 8822c: add LC calibration for RTL8822C")
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210426013252.5665-3-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cc816ef9d ]
The FW has a watchdog of 200ms in the PNVM load flow, so the driver
should have a slightly higher timeout. Change the timeout from 100ms
to 250ms.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 70d3ca86b0 ("iwlwifi: mvm: ring the doorbell and wait for PNVM load completion")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210612142637.ba22aec1e2be.I36bfadc28c480f4fc57266c075a79e8ea4a6934f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8b79c414e ]
8021q module adds vlan 0 to all interfaces when it starts.
When 8021q module is loaded it isn't possible to create bond
with mv88e6xxx interfaces, bonding module dipslay error
"Couldn't add bond vlan ids", because it tries to add vlan 0
to slave interfaces.
There is unexpected behavior in the switch. When a PVID
is assigned to a port the switch changes VID to PVID
in ingress frames with VID 0 on the port. Expected
that the switch doesn't assign PVID to tagged frames
with VID 0. But there isn't a way to change this behavior
in the switch.
Fixes: 57e661aae6 ("net: dsa: mv88e6xxx: Link aggregation support")
Signed-off-by: Eldar Gasanov <eldargasanov2@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b90788459c ]
If this test fails we must free some resources as in all the other error
handling paths of this function.
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 603113c514 ]
Non-ND strict packets with a source LLA go through the packet taps
again, while non-ND strict packets with other source addresses do not,
and we can see a clone of those packets on the vrf interface (we should
not). This is due to a series of changes:
Commit 6f12fa775530[1] made non-ND strict packets not being pushed again
in the packet taps. This changed with commit 205704c618af[2] for those
packets having a source LLA, as they need a lookup with the orig_iif.
The issue now is those packets do not skip the 'vrf_ip6_rcv' function to
the end (as the ones without a source LLA) and go through the check to
call packet taps again. This check was changed by commit 6f12fa775530[1]
and do not exclude non-strict packets anymore. Packets matching
'need_strict && !is_ndisc && is_ll_src' are now being sent through the
packet taps again. This can be seen by dumping packets on the vrf
interface.
Fix this by having the same code path for all non-ND strict packets and
selectively lookup with the orig_iif for those with a source LLA. This
has the effect to revert to the pre-205704c618af[2] condition, which
should also be easier to maintain.
[1] 6f12fa7755 ("vrf: mark skb for multicast or link-local as enslaved to VRF")
[2] 205704c618 ("vrf: packets with lladdr src needs dst at input with orig_iif when needs strict")
Fixes: 205704c618 ("vrf: packets with lladdr src needs dst at input with orig_iif when needs strict")
Cc: Stephen Suryaputra <ssuryaextr@gmail.com>
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0de449d599 ]
As documented at drivers/base/platform.c for platform_get_irq:
* Gets an IRQ for a platform device and prints an error message if finding the
* IRQ fails. Device drivers should check the return value for errors so as to
* not pass a negative integer value to the request_irq() APIs.
So, the driver should check that platform_get_irq() return value
is _negative_, not that it's equal to zero, because -ENXIO (return
value from request_irq() if irq was not found) will
pass this check and it leads to passing negative irq to request_irq()
Fixes: 0dd0770936 ("NET: Add ezchip ethernet driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4b8700e07 ]
priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after netif_napi_del()
call.
Fixes: 0dd0770936 ("NET: Add ezchip ethernet driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3a5de6d81 ]
static int greth_of_remove(struct platform_device *of_dev)
{
...
struct greth_private *greth = netdev_priv(ndev);
...
unregister_netdev(ndev);
free_netdev(ndev);
of_iounmap(&of_dev->resource[0], greth->regs, resource_size(&of_dev->resource[0]));
...
}
greth is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing greth
pointer. So, fix it by moving free_netdev() after of_iounmap()
call.
Fixes: d4c41139df ("net: Add Aeroflex Gaisler 10/100/1G Ethernet MAC driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 723885a675 ]
Fix the maximum size of the coredump generated with current mt7921
firmware. Otherwise, a truncated coredump would be reported to userland
via dev_coredumpv.
Also, there is an additional error handling enhanced in the patch to avoid
the possible invalid buffer access when the system failed to create the
buffer to hold the coredump.
Fixes: 0da3c795d0 ("mt76: mt7921: add coredump support")
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89043529c8 ]
FCS error packets are filtered by default and won't be reported to
driver, so that RX fcs error and PER in testmode always show zero.
Fix this issue by reading fcs error count from hw counter.
We did't fix this issue by disabling fcs error rx filter since it may
let HW suffer some SER errors.
Fixes: 5d8a83f099 ("mt76: mt7915: implement testmode rx support")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 271fa68536 ]
Always wake the device up before dumping the single_sku power table
otherwise the device can hang.
Fixes: ea29acc97c ("mt76: mt7921: add dumping Tx power table")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 223cea6d3c ]
Get rid of an undefined behaviour in mt76_testmode_alloc_skb routine
allocating skb frames
Fixes: 2601dda8fa ("mt76: testmode: add support to send larger packet")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe2c3b1fc6 ]
Free all pending frames in case of failure in mt76_testmode_alloc_skb
routine
Fixes: 2601dda8fa ("mt76: testmode: add support to send larger packet")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07ac384b4 ]
Avoid unnecessary consecutive WiFi resets by dropping reset
request when reset work is working.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 213f87289e ]
OMAC idx have to be same with BSS idx according to firmware usage.
Fixes: e0f9fdda81 ("mt76: mt7921: add ieee80211_ops")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10de032a31 ]
Hw beacon cmd to the mt7921 firmware doesn't only filter out the beacon,
but also performs its own connection monitoring, including periodic
keep-alives to the AP and probing the AP on beacon loss. Will indicate
the host with the event when the firmware detects the connection is lost.
Fixes: 1d8efc741d ("mt76: mt7921: introduce Runtime PM support")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edb5aebc1c ]
It is possible the RCPI from the certain antenna is an invalid value,
especially packets are receiving while the system is frequently entering
deep sleep mode, so consider calculating RSSI with the reasonable upper
bound to avoid report the wrong value to the mac80211 layer.
Fixes: 163f4d22c1 ("mt76: mt7921: add MAC support")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 193e5f22ee ]
Update MCU command usage to fix WoW configuration with disconnection
and bitmap pattern and to avoid magic number.
Fixes: ffa1bf9742 ("mt76: mt7921: introduce PM support")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bfa291251 ]
If the device is MMIO-based, we must ensure all TxD/TxP on the host
memory all being consumed by the device prior to safely switching to
fw_own state.
Fixes: ec7bd7b4a9 ("mt76: connac: check wake refcount in mcu_fw_pmctrl")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20eb83c749 ]
WiFi subsytem reset should control MT_WFSYS_SW_RST_B and then poll the
same register until the bit WFSYS_SW_INIT_DONE bit is set.
Fixes: 0c1ce98846 ("mt76: mt7921: add wifi reset support")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d3cdc1bbb ]
Fix theoretical NULL pointer dereference in mt7615_tx_prepare_skb and
mt7663_usb_sdio_tx_prepare_skb routines. This issue has been identified
by code analysis.
Fixes: 6aa4ed7927 ("mt76: mt7615: implement DMA support for MT7622")
Fixes: 4bb586bc33 ("mt76: mt7663u: sync probe sampling with rate configuration")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
