[ Upstream commit 7917e90667 ]
The B_SESS_VLD_WAKEUP_EN bit 6 was added by a mistake in a previous
commit. This bit corresponds to B_SESS_END_WAKEUP_EN, which we don't use.
The B_VBUS_VLD_WAKEUP_EN doesn't exist at all and B_SESS_VLD_WAKEUP_EN
needs to be in place of it. We don't utilize B-sensors in the driver,
so it never was a problem, nevertheless let's correct the definition of
the bits.
Fixes: 35192007d2 ("usb: phy: tegra: Support waking up from a low power mode")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210613145936.9902-2-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f8d39a8ef ]
Some devices need an extra delay after losing VBUS, otherwise VBUS may
be detected as active at suspend time, preventing the PHY's suspension
by the VBUS detection sensor. This problem was found on Asus Transformer
TF700T (Tegra30) tablet device, where the USB PHY wakes up immediately
from suspend because VBUS sensor continues to detect VBUS as active after
disconnection. We need to poll the PHY's VBUS wakeup status until it's
deasserted before suspending PHY in order to fix this minor trouble.
Fixes: 35192007d2 ("usb: phy: tegra: Support waking up from a low power mode")
Reported-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210613145936.9902-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aafe93516b ]
Every time the hub signals a reset while we (device) are hsotg->connected,
dwc2_hsotg_core_init_disconnected() is called, which in turn calls
dwc2_hs_phy_init().
GUSBCFG.USBTrdTim is cleared upon Core Soft Reset, so if
hsotg->params.phy_utmi_width is 8-bit, the value of GUSBCFG.USBTrdTim (the
default one: 0x5, corresponding to 16-bit) is always different from
hsotg->params.phy_utmi_width, thus dwc2_core_reset() is called every
time (usbcfg != usbcfg_old), which causes 2 issues:
1) The call to dwc2_core_reset() does another reset 300us after the initial
Chirp K of the first reset (which should last at least Tuch = 1ms), and
messes up the High-speed Detection Handshake: both hub and device drive
current into the D+ and D- lines at the same time.
2) GUSBCFG.USBTrdTim is cleared by the second reset, so its value is always
the default one (0x5).
Setting GUSBCFG.USBTrdTim after the potential call to dwc2_core_reset()
fixes both issues. It is now set even when select_phy is false because the
cost of the Core Soft Reset is removed.
Fixes: 1e868545f2 ("usb: dwc2: gadget: Move gadget phy init into core phy init")
Signed-off-by: Clément Lassieur <clement@lassieur.org>
Link: https://lore.kernel.org/r/20210603155921.940651-1-clement@lassieur.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d112efbe6d ]
During PR_SWAP, When TCPM is in PR_SWAP_SNK_SRC_SINK_OFF, vbus is
expected to reach VSAFE0V when source turns off vbus. Do not move
to SNK_UNATTACHED state when this happens.
Fixes: 28b43d3d74 ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b31d9d6d7a upstream.
when system is doing s4, the process of xhci_resume may be as below:
1、xhci_mem_cleanup
2、xhci_init->xhci_mem_init->xhci_mem_cleanup(when memory is not enough).
xhci_mem_cleanup will be executed twice when system is out of memory.
xhci->port_caps is freed in xhci_mem_cleanup,but it isn't set to NULL.
It will be freed twice when xhci_mem_cleanup is called the second time.
We got following bug when system resumes from s4:
kernel BUG at mm/slub.c:309!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
CPU: 0 PID: 5929 Tainted: G S W 5.4.96-arm64-desktop #1
pc : __slab_free+0x5c/0x424
lr : kfree+0x30c/0x32c
Call trace:
__slab_free+0x5c/0x424
kfree+0x30c/0x32c
xhci_mem_cleanup+0x394/0x3cc
xhci_mem_init+0x9ac/0x1070
xhci_init+0x8c/0x1d0
xhci_resume+0x1cc/0x5fc
xhci_plat_resume+0x64/0x70
platform_pm_thaw+0x28/0x60
dpm_run_callback+0x54/0x24c
device_resume+0xd0/0x200
async_resume+0x24/0x60
async_run_entry_fn+0x44/0x110
process_one_work+0x1f0/0x490
worker_thread+0x5c/0x450
kthread+0x158/0x160
ret_from_fork+0x10/0x24
Original patch that caused this issue was backported to 4.4 stable,
so this should be backported to 4.4 stabe as well.
Fixes: cf0ee7c60c ("xhci: Fix memory leak when caching protocol extended capability PSI tables - take 2")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: Tao Xue <xuetao09@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03026197bb upstream.
typec_register_altmode() misses to call altmode_id_remove() in an error
path. Add the missed function call to fix it.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Link: https://lore.kernel.org/r/20210617073226.47599-1-jingxiangfeng@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b537cf877 upstream.
If the voltage is being decreased in power negotiation, the Source will
set the power supply to operate at the new voltage level before sending
PS_RDY. Relax the threshold before sending Request Message so that it
will not race with Source which begins to adjust the voltage right after
it sends Accept Message (PPS) or tSrcTransition (25~35ms) after it sends
Accept Message (non-PPS).
The real threshold will be set after Sink receives PS_RDY Message.
Fixes: f321a02cae ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Cc: stable <stable@vger.kernel.org>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210616090102.1897674-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4288debeaa upstream.
"Table 4-3 VBUS Sink Characteristics" of "Type-C Cable and Connector
Specification" defines the disconnect voltage thresholds of various
configurations. This change fixes the disconnect threshold voltage
calculation based on vSinkPD_min and vSinkDisconnectPD as defined
by the table.
Fixes: e1a97bf80a ("usb: typec: tcpci: Implement Auto discharge disconnect callbacks")
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210615174323.1160132-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84524d1232 upstream.
Creation EP's debugfs called earlier than debugfs folder for dwc3
device created. As result EP's debugfs are created in '/sys/kernel/debug'
instead of '/sys/kernel/debug/usb/dwc3.1.auto'.
Moved dwc3_debugfs_init() function call before calling
dwc3_core_init_mode() to allow create dwc3 debugfs parent before
creating EP's debugfs's.
Fixes: 8d396bb0a5 ("usb: dwc3: debugfs: Add and remove endpoint dirs dynamically")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/01fafb5b2d8335e98e6eadbac61fc796bdf3ec1a.1623948457.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4897807753 upstream.
The device (32a7:0000 Heimann Sensor GmbH USB appset demo) claims to be
a CDC-ACM device in its descriptors but in fact is not. If it is run
with echo disabled it returns garbled data, probably due to something
that happens in the TTY layer. And when run with echo enabled (the
default), it will mess up the calibration data of the sensor the first
time any data is sent to the device.
In short, I had a bad time after connecting the sensor and trying to get
it to work. I hope blacklisting it in the cdc-acm driver will save
someone else a bit of trouble.
Signed-off-by: Hannu Hartikainen <hannu@hrtk.in>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210622141454.337948-1-hannu@hrtk.in
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d143825baf upstream.
The ROM load sometimes seems to return an unknown status
(RENESAS_ROM_STATUS_NO_RESULT) instead of success / fail.
If the ROM load indeed failed this leads to failures when trying to
communicate with the controller later on.
Attempt to load firmware using RAM load in those cases.
Fixes: 2478be82de ("usb: renesas-xhci: Add ROM loader for uPD720201")
Cc: stable@vger.kernel.org
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Link: https://lore.kernel.org/r/20210615153758.253572-1-mdf@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4249d6fbc1 upstream.
when receive eem echo command, it will send a response,
but queue this response to the usb request which allocate
from gadget device endpoint zero,
and transmit the request to IN endpoint of eem interface.
on dwc3 gadget, it will trigger following warning in function
__dwc3_gadget_ep_queue(),
if (WARN(req->dep != dep, "request %pK belongs to '%s'\n",
&req->request, req->dep->name))
return -EINVAL;
fix it by allocating a usb request from IN endpoint of eem interface,
and transmit the usb request to same IN endpoint of eem interface.
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210616115142.34075-1-linyyuan@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress CY7C65632 appears to have an issue with auto suspend and
detecting devices, not too dissimilar to the SMSC 5534B hub. It is
easiest to reproduce by connecting multiple mass storage devices to
the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts
result in the devices not being detected. It is however possible to
make them appear using lsusb -v.
Disabling autosuspend for this hub resolves the issue.
Fixes: 1208f9e1d7 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmDJT3gACgkQSFkpgVDW
cbvh6QgAucjmka2WfiFraPRij4SyveqgTUQtmjLWhNcVugla6eHJTmsRlTvqj3YT
zBRv418FRQZmbwojOM/Vai49qcG+/nJGJDAupQ5v+tUmtzb0BIyNSxLnBpgrspFK
8qBUA3lF7JLz4xsXwICNLNvvvcCPjYOVfk3430FpkythJIK5UCFidkrUB2S/p6/1
OpzWMICZxv4kdSxf7EkfOhjbfzqJZcJZR+sDjYNnOA4gLGClkE0OQC9k+qIpIEDs
UHxtL0fmToW0EOv/14SBRVTlfqKH5WgEUDlodNw7wVYSfMx1NoU2UgwcytD2SZX8
7dcDhvuT2YZv/HuV83vYAgN5hJRCmQ==
=Drqs
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One bug fix for USB charger detection at imx7d and imx8m series SoCs
* tag 'usb-v5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: imx: Fix Battery Charger 1.2 CDP detection
i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
following CDP timing requirements defined by USB BC 1.2 specification
and section 3.2.4 Detection Timing CDP.
During Primary Detection the i.MX device should turn on VDP_SRC and
IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
the i.MX is allowed to check the status of the D- line. Current
implementation is waiting between 1ms and 2ms, and certain BC 1.2
complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
enough time for primary detection.
During secondary detection the i.MX is required to disable VDP_SRC and
IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).
Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
disable sequence in imx7d_charger_secondary_detection() function.
VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
Increase delay allowing enough time for detection.
Cc: <stable@vger.kernel.org>
Fixes: 746f316b75 ("usb: chipidea: introduce imx7d USB charger detection")
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Jun Li <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20210614175013.495808-1-breno.lima@nxp.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Here are two fixes for the cp210x driver. The first fixes a regression
with early revisions of the CP2102N which specifically broke some ESP32
development boards. The second makes sure that the pin configuration is
detected properly also for the CP2102N QFN20 package.
Both have been in linux-next over night and with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYMM1XQAKCRALxc3C7H1l
CH1DAQDlY9HI8ujDidiFHqBw/UduU7jmncuiGR/sAVzEAstPigD/VOJH+cD/yn7Z
35gSi1DvdrBRjs8qTlzZvoiSN81nTgM=
=yLzP
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.13-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.13-rc6
Here are two fixes for the cp210x driver. The first fixes a regression
with early revisions of the CP2102N which specifically broke some ESP32
development boards. The second makes sure that the pin configuration is
detected properly also for the CP2102N QFN20 package.
Both have been in linux-next over night and with no reported issues.
* tag 'usb-serial-5.13-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: fix CP2102N-A01 modem control
USB: serial: cp210x: fix alternate function for CP2102N QFN20
This reverts commit e0e8b6abe8.
Turns out this breaks the build. We had numerous reports of problems
from linux-next and 0-day about this not working properly, so revert it
for now until it can be figured out properly.
The build errors are:
arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x29d4): undefined reference to `fsl_udc_clk_finalize'
arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x2ba8): undefined reference to `fsl_udc_clk_release'
fsl_udc_core.c:(.text+0x2848): undefined reference to `fsl_udc_clk_init'
fsl_udc_core.c:(.text+0xe88): undefined reference to `fsl_udc_clk_release'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e0e8b6abe8 ("usb: gadget: fsl: Re-enable driver for ARM SoCs")
Cc: stable <stable@vger.kernel.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Leo Li <leoyang.li@nxp.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the copy-paste mistake in the return path of typec_mux_match(),
where dev is considered a member of struct typec_switch rather than
struct typec_mux.
The two structs are identical in regards to having the struct device as
the first entry, so this provides no functional change.
Fixes: 3370db3519 ("usb: typec: Registering real device entries for the muxes")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210610002132.3088083-1-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ucsi_init() fails for some reason (e.g. ucsi_register_port()
fails or general communication failure to the PPM), particularly at
any point after the GET_CAPABILITY command had been issued, this
results in unwinding the initialization and returning an error.
However the ucsi structure's ucsi_capability member retains its
current value, including likely a non-zero num_connectors.
And because ucsi_init() itself is done in a workqueue a UCSI
interface driver will be unaware that it failed and may think the
ucsi_register() call was completely successful. Later, if
ucsi_unregister() is called, due to this stale ucsi->cap value it
would try to access the items in the ucsi->connector array which
might not be in a proper state or not even allocated at all and
results in NULL or invalid pointer dereference.
Fix this by clearing the ucsi->cap value to 0 during the error
path of ucsi_init() in order to prevent a later ucsi_unregister()
from entering the connector cleanup loop.
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210609073535.5094-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a390bef7db ("usb: gadget: fsl_mxc_udc: Remove the driver")
dropped the ARCH_MXC dependency from USB_FSL_USB2, leaving it depending
solely on FSL_SOC.
FSL_SOC is powerpc only; it was briefly available on ARM in 2014 but was
removed by commit cfd074ad86 ("ARM: imx: temporarily remove
CONFIG_SOC_FSL from LS1021A"). Therefore the driver can no longer be
enabled on ARM platforms.
This appears to be a mistake as arm64's ARCH_LAYERSCAPE and arm32
SOC_LS1021A SoCs use this symbol. It's enabled in these defconfigs:
arch/arm/configs/imx_v6_v7_defconfig:CONFIG_USB_FSL_USB2=y
arch/arm/configs/multi_v7_defconfig:CONFIG_USB_FSL_USB2=y
arch/powerpc/configs/mgcoge_defconfig:CONFIG_USB_FSL_USB2=y
arch/powerpc/configs/mpc512x_defconfig:CONFIG_USB_FSL_USB2=y
To fix, expand the dependencies so USB_FSL_USB2 can be enabled on the
ARM platforms, and with COMPILE_TEST.
Fixes: a390bef7db ("usb: gadget: fsl_mxc_udc: Remove the driver")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210610034957.93376-1-joel@jms.id.au
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As LKP noticed the Sparse is not happy about strict type handling:
.../typec/tcpm/wcove.c:380:50: sparse: expected unsigned short [usertype] header
.../typec/tcpm/wcove.c:380:50: sparse: got restricted __le16 const [usertype] header
Fix this by switching to use pd_header_cnt_le() instead of pd_header_cnt()
in the affected code.
Fixes: ae8a2ca8a2 ("usb: typec: Group all TCPCI/TCPM code together")
Fixes: 3c4fb9f169 ("usb: typec: wcove: start using tcpm for USB PD support")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210609172202.83377-1-andriy.shevchenko@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CP2102N revision A01 (firmware version <= 1.0.4) has a buggy
flow-control implementation that uses the ulXonLimit instead of
ulFlowReplace field of the flow-control settings structure (erratum
CP2102N_E104).
A recent change that set the input software flow-control limits
incidentally broke RTS control for these devices when CRTSCTS is not set
as the new limits would always enable hardware flow control.
Fix this by explicitly disabling flow control for the buggy firmware
versions and only updating the input software flow-control limits when
IXOFF is requested. This makes sure that the terminal settings matches
the default zero ulXonLimit (ulFlowReplace) for these devices.
Link: https://lore.kernel.org/r/20210609161509.9459-1-johan@kernel.org
Reported-by: David Frey <dpfrey@gmail.com>
Reported-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Tested-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Fixes: f61309d9c9 ("USB: serial: cp210x: set IXOFF thresholds")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan@kernel.org>
The QFN20 part has a different GPIO/port function assignment. The
configuration struct bit field ordered as TX/RX/RS485/WAKEUP/CLK
which exactly matches GPIO0-3 for QFN24/28. However, QFN20 has a
different GPIO to primary function assignment.
Special case QFN20 to follow to properly detect which GPIOs are
available.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://lore.kernel.org/r/51830b2b24118eb0f77c5c9ac64ffb2f519dbb1d.1622218300.git.stefan@agner.ch
Fixes: c8acfe0aad ("USB: serial: cp210x: implement GPIO support for CP2102N")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Johan Hovold <johan@kernel.org>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Fixes: 517c4c44b3 ("usb: Add driver to allow any GPIO to be used for 7211 USB signals")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210605080914.2057758-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no validation of the index from dwc3_wIndex_to_dep() and we might
be referring a non-existing ep and trigger a NULL pointer exception. In
certain configurations we might use fewer eps and the index might wrongly
indicate a larger ep index than existing.
By adding this validation from the patch we can actually report a wrong
index back to the caller.
In our usecase we are using a composite device on an older kernel, but
upstream might use this fix also. Unfortunately, I cannot describe the
hardware for others to reproduce the issue as it is a proprietary
implementation.
[ 82.958261] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a4
[ 82.966891] Mem abort info:
[ 82.969663] ESR = 0x96000006
[ 82.972703] Exception class = DABT (current EL), IL = 32 bits
[ 82.978603] SET = 0, FnV = 0
[ 82.981642] EA = 0, S1PTW = 0
[ 82.984765] Data abort info:
[ 82.987631] ISV = 0, ISS = 0x00000006
[ 82.991449] CM = 0, WnR = 0
[ 82.994409] user pgtable: 4k pages, 39-bit VAs, pgdp = 00000000c6210ccc
[ 83.000999] [00000000000000a4] pgd=0000000053aa5003, pud=0000000053aa5003, pmd=0000000000000000
[ 83.009685] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[ 83.026433] Process irq/62-dwc3 (pid: 303, stack limit = 0x000000003985154c)
[ 83.033470] CPU: 0 PID: 303 Comm: irq/62-dwc3 Not tainted 4.19.124 #1
[ 83.044836] pstate: 60000085 (nZCv daIf -PAN -UAO)
[ 83.049628] pc : dwc3_ep0_handle_feature+0x414/0x43c
[ 83.054558] lr : dwc3_ep0_interrupt+0x3b4/0xc94
...
[ 83.141788] Call trace:
[ 83.144227] dwc3_ep0_handle_feature+0x414/0x43c
[ 83.148823] dwc3_ep0_interrupt+0x3b4/0xc94
[ 83.181546] ---[ end trace aac6b5267d84c32f ]---
Signed-off-by: Marian-Cristian Rotariu <marian.c.rotariu@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210608162650.58426-1-marian.c.rotariu@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when skb_clone() or skb_copy_expand() fail,
it should pull skb with lengh indicated by header,
or not it will read network data and check it as header.
Cc: <stable@vger.kernel.org>
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.com>
Link: https://lore.kernel.org/r/20210608233547.3767-1-linyyuan@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For ACPI devices we have a symmetric API to put them, so use it in the driver.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210607205007.71458-3-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource() can return an error, add missed check for it.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210607205007.71458-2-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210607205007.71458-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the VDM responses couldn't be sent successfully, it doesn't need to
finish the AMS until the retry count reaches the limit.
Fixes: 0908c5aca3 ("usb: typec: tcpm: AMS and Collision Avoidance")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210606081452.764032-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_assign_descriptors() is called with 5 parameters,
the last 4 of which are the usb_descriptor_header for:
full-speed (USB1.1 - 12Mbps [including USB1.0 low-speed @ 1.5Mbps),
high-speed (USB2.0 - 480Mbps),
super-speed (USB3.0 - 5Gbps),
super-speed-plus (USB3.1 - 10Gbps).
The differences between full/high/super-speed descriptors are usually
substantial (due to changes in the maximum usb block size from 64 to 512
to 1024 bytes and other differences in the specs), while the difference
between 5 and 10Gbps descriptors may be as little as nothing
(in many cases the same tuning is simply good enough).
However if a gadget driver calls usb_assign_descriptors() with
a NULL descriptor for super-speed-plus and is then used on a max 10gbps
configuration, the kernel will crash with a null pointer dereference,
when a 10gbps capable device port + cable + host port combination shows up.
(This wouldn't happen if the gadget max-speed was set to 5gbps, but
it of course defaults to the maximum, and there's no real reason to
artificially limit it)
The fix is to simply use the 5gbps descriptor as the 10gbps descriptor,
if a 10gbps descriptor wasn't provided.
Obviously this won't fix the problem if the 5gbps descriptor is also
NULL, but such cases can't be so trivially solved (and any such gadgets
are unlikely to be used with USB3 ports any way).
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210609024459.1126080-1-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids a null pointer dereference in
f_{ecm,eem,hid,loopback,printer,rndis,serial,sourcesink,subset,tcm}
by simply reusing the 5gbps config for 10gbps.
Fixes: eaef50c760 ("usb: gadget: Update usb_assign_descriptors for SuperSpeedPlus")
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Michael R Sweet <msweet@msweet.org>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Sudhakar Panneerselvam <sudhakar.panneerselvam@oracle.com>
Cc: Wei Ming Chen <jj251510319013@gmail.com>
Cc: Will McVicker <willmcvicker@google.com>
Cc: Zqiang <qiang.zhang@windriver.com>
Reviewed-By: Lorenzo Colitti <lorenzo@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210608044141.3898496-1-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI controller is required to enter D3hot rather than D3cold for AMD
s2idle on this hardware generation.
Otherwise, the 'Controller Not Ready' (CNR) bit is not being cleared by
host in resume and eventually this results in xhci resume failures during
the s2idle wakeup.
Link: https://lore.kernel.org/linux-usb/1612527609-7053-1-git-send-email-Prike.Liang@amd.com/
Suggested-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable <stable@vger.kernel.org> # 5.11+
Link: https://lore.kernel.org/r/20210527154534.8900-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reasoning for this change is that if we already had
a packet pending, then we also already had a pending timer,
and as such there is no need to reschedule it.
This also prevents packets getting delayed 60 ms worst case
under a tiny packet every 290us transmit load, by keeping the
timeout always relative to the first queued up packet.
(300us delay * 16KB max aggregation / 80 byte packet =~ 60 ms)
As such the first packet is now at most delayed by 300us.
Under low transmit load, this will simply result in us sending
a shorter aggregate, as originally intended.
This patch has the benefit of greatly reducing (by ~10 factor
with 1500 byte frames aggregated into 16 kiB) the number of
(potentially pretty costly) updates to the hrtimer.
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210608085438.813960-1-zenczykowski@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmC9dVwACgkQSFkpgVDW
cbs+oAf/b4mVmJpYIMTBM5tU086YpsZ80StjH3MVx2Hx/F8bM2ewovOUxOWPAY2o
A6ROuLUlU/0TT8U3LL5PEbQDHhuPsf1n3erv6iz63a72uzOouLeHOBYFP+E6aM5z
1mkr2yHXpwFe+aHpstXvOgeR4ano0kzMkx/I3SPH6P8/pXiBSrpvTiBwnxqvZxbb
VQuP9VfEF5e8vXuDiMF1V5qjea/BYnvjt2Yj34An3JHte13oTNRdFM/6aQiIEvt2
r6g0nBJizmhIHwtNYq30KfgFsNjiC9+dPtOCOVyv80c+Qu+F71EwEyqZSrOVLunh
hfxC/U6H8vy73Zo3gJP3xrXE+xvztw==
=OpDk
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Two bug fixes for cdns3 and cdnsp
* tag 'usb-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdnsp: Fix deadlock issue in cdnsp_thread_irq_handler
usb: cdns3: Enable TDL_CHK only for OUT ep
Here's a fix for some pipe-direction mismatches in the quatech2 driver,
and a couple of new device ids for ftdi_sio and omninet (and a related
trivial cleanup).
All but the ftdi_sio commit have been in linux-next, and with no
reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYLtSqwAKCRALxc3C7H1l
CPj2AQDSM/GeQ658vxYKPIA+8ZDBWubaYhq8KAUDqxL7hBMevAEAkbFhjgtyQt4h
32lqF2YsahxCHckvLXSnxxj1cTJxGAk=
=NKr6
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.13-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Jonah writes:
USB-serial fixes for 5.13-rc5
Here's a fix for some pipe-direction mismatches in the quatech2 driver,
and a couple of new device ids for ftdi_sio and omninet (and a related
trivial cleanup).
All but the ftdi_sio commit have been in linux-next, and with no
reported issues.
* tag 'usb-serial-5.13-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add NovaTech OrionMX product ID
USB: serial: omninet: update driver description
USB: serial: omninet: add device id for Zyxel Omni 56K Plus
USB: serial: quatech2: fix control-request directions
Add PID for the NovaTech OrionMX so it can be automatically detected.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
During unbind, ffs_func_eps_disable() will be executed, resulting in
completion callbacks for any pending USB requests. When using AIO,
irrespective of the completion status, io_data work is queued to
io_completion_wq to evaluate and handle the completed requests. Since
work runs asynchronously to the unbind() routine, there can be a
scenario where the work runs after the USB gadget has been fully
removed, resulting in accessing of a resource which has been already
freed. (i.e. usb_ep_free_request() accessing the USB ep structure)
Explicitly drain the io_completion_wq, instead of relying on the
destroy_workqueue() (in ffs_data_put()) to make sure no pending
completion work items are running.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1621644261-1236-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the state_machine_timer, we should also cancel possible pending
send discover identity hrtimer when unregister tcpm port.
Fixes: c34e85fa69 ("usb: typec: tcpm: Send DISCOVER_IDENTITY from dedicated work")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1622627829-11070-3-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the state_machine_timer, we should also cancel possible pending
frs hrtimer when unregister tcpm port.
Fixes: 8dc4bd0736 ("usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1622627829-11070-2-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving Alert Message, if it is not unexpected but is
unsupported for some reason, the port should return Not_Supported
Message response.
Also, according to PD3.0 Spec 6.5.2.1.4 Event Flags Field, the
OTP/OVP/OCP flags in the Event Flags field in Status Message no longer
require Get_PPS_Status Message to clear them. Thus remove it when
receiving Status Message with those flags being set.
In addition, add the missing AMS operations for Status Message.
Fixes: 64f7c494a3 ("typec: tcpm: Add support for sink PPS related messages")
Fixes: 0908c5aca3 ("usb: typec: tcpm: AMS and Collision Avoidance")
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210531164928.2368606-1-kyletso@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When only PHY1 is used (for example on Odroid-HC4), the regmap init code
uses the usb2 ports when doesn't initialize the PHY1 regmap entry.
This fixes:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
...
pc : regmap_update_bits_base+0x40/0xa0
lr : dwc3_meson_g12a_usb2_init_phy+0x4c/0xf8
...
Call trace:
regmap_update_bits_base+0x40/0xa0
dwc3_meson_g12a_usb2_init_phy+0x4c/0xf8
dwc3_meson_g12a_usb2_init+0x7c/0xc8
dwc3_meson_g12a_usb_init+0x28/0x48
dwc3_meson_g12a_probe+0x298/0x540
platform_probe+0x70/0xe0
really_probe+0xf0/0x4d8
driver_probe_device+0xfc/0x168
...
Fixes: 013af227f5 ("usb: dwc3: meson-g12a: handle the phy and glue registers separately")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210601084830.260196-1-narmstrong@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an error occurs after a successful 'regulator_enable()' call,
'regulator_disable()' must be called.
Fix the error handling path of the probe accordingly.
The remove function doesn't need to be fixed, because the
'regulator_disable()' call is already hidden in 'dwc3_meson_g12a_suspend()'
which is called via 'pm_runtime_set_suspended()' in the remove function.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/79df054046224bbb0716a8c5c2082650290eec86.1621616013.git.christophe.jaillet@wanadoo.fr
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_ams_start is used to initiate an AMS as well as checking Collision
Avoidance conditions but not for flagging passive AMS (initiated by the
port partner). Fix the misuses of tcpm_ams_start in tcpm_pd_svdm.
ATTENTION doesn't need responses so the AMS flag is not needed here.
Fixes: 0bc3ee9288 ("usb: typec: tcpm: Properly interrupt VDM AMS")
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210601123151.3441914-5-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ID Header VDO and Product VDOs defined in USB PD Spec rev 2.0 and
rev 3.1 are quite different. Add an additional array snk_vdo_v1 and
send it as the response to the port partner if it only supports SVDM
version 1.0.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210601123151.3441914-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In USB PD Spec Rev 3.1 Ver 1.0, section "6.12.5 Applicability of
Structured VDM Commands", DFP is allowed and recommended to respond to
Discovery Identity with ACK. And in section "6.4.4.2.5.1 Commands other
than Attention", NAK should be returned only when receiving Messages
with invalid fields, Messages in wrong situation, or unrecognize
Messages.
Still keep the original design for SVDM Version 1.0 for backward
compatibilities.
Fixes: 193a68011f ("staging: typec: tcpm: Respond to Discover Identity commands")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210601123151.3441914-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
