commit 6c3fc0b1c3 upstream.
A large tx latency issue was discovered during testing when only QBV was
enabled. The issue occurs because gtxoffset was not set when QBV is
active, it was only set when launch time is active.
The patch "igc: Correct the launchtime offset" only sets gtxoffset when
the launchtime_enable field is set by the user. Enabling launchtime_enable
ultimately sets the register IGC_TXQCTL_QUEUE_MODE_LAUNCHT (referred to as
LaunchT in the SW user manual).
Section 7.5.2.6 of the IGC i225/6 SW User Manual Rev 1.2.4 states:
"The latency between transmission scheduling (launch time) and the
time the packet is transmitted to the network is listed in Table 7-61."
However, the patch misinterprets the phrase "launch time" in that section
by assuming it specifically refers to the LaunchT register, whereas it
actually denotes the generic term for when a packet is released from the
internal buffer to the MAC transmit logic.
This launch time, as per that section, also implicitly refers to the QBV
gate open time, where a packet waits in the buffer for the QBV gate to
open. Therefore, latency applies whenever QBV is in use. TSN features such
as QBU and QAV reuse QBV, making the latency universal to TSN features.
Discussed with i226 HW owner (Shalev, Avi) and we were in agreement that
the term "launch time" used in Section 7.5.2.6 is not clear and can be
easily misinterpreted. Avi will update this section to:
"When TQAVCTRL.TRANSMIT_MODE = TSN, the latency between transmission
scheduling and the time the packet is transmitted to the network is listed
in Table 7-61."
Fix this issue by using igc_tsn_is_tx_mode_in_tsn() as a condition to
write to gtxoffset, aligning with the newly updated SW User Manual.
Tested:
1. Enrol taprio on talker board
base-time 0
cycle-time 1000000
flags 0x2
index 0 cmd S gatemask 0x1 interval1
index 0 cmd S gatemask 0x1 interval2
Note:
interval1 = interval for a 64 bytes packet to go through
interval2 = cycle-time - interval1
2. Take tcpdump on listener board
3. Use udp tai app on talker to send packets to listener
4. Check the timestamp on listener via wireshark
Test Result:
100 Mbps: 113 ~193 ns
1000 Mbps: 52 ~ 84 ns
2500 Mbps: 95 ~ 223 ns
Note that the test result is similar to the patch "igc: Correct the
launchtime offset".
Fixes: 790835fcc0 ("igc: Correct the launchtime offset")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0afeaeb5da upstream.
Following the "igc: Fix TX Hang issue when QBV Gate is close" changes,
remaining issues with the reset adapter logic in igc_tsn_offload_apply()
have been observed:
1. The reset adapter logics for i225 and i226 differ, although they should
be the same according to the guidelines in I225/6 HW Design Section
7.5.2.1 on software initialization during tx mode changes.
2. The i225 resets adapter every time, even though tx mode doesn't change.
This occurs solely based on the condition igc_is_device_id_i225() when
calling schedule_work().
3. i226 doesn't reset adapter for tsn->legacy tx mode changes. It only
resets adapter for legacy->tsn tx mode transitions.
4. qbv_count introduced in the patch is actually not needed; in this
context, a non-zero value of qbv_count is used to indicate if tx mode
was unconditionally set to tsn in igc_tsn_enable_offload(). This could
be replaced by checking the existing register
IGC_TQAVCTRL_TRANSMIT_MODE_TSN bit.
This patch resolves all issues and enters schedule_work() to reset the
adapter only when changing tx mode. It also removes reliance on qbv_count.
qbv_count field will be removed in a future patch.
Test ran:
1. Verify reset adapter behaviour in i225/6:
a) Enrol a new GCL
Reset adapter observed (tx mode change legacy->tsn)
b) Enrol a new GCL without deleting qdisc
No reset adapter observed (tx mode remain tsn->tsn)
c) Delete qdisc
Reset adapter observed (tx mode change tsn->legacy)
2. Tested scenario from "igc: Fix TX Hang issue when QBV Gate is closed"
to confirm it remains resolved.
Fixes: 175c241288 ("igc: Fix TX Hang issue when QBV Gate is closed")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
[ Only want the igc_tsn_is_tx_mode_in_tsn() portion of this for older stable
kernels - gregkh ]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit defd8b3c37 ]
When sockfd_lookup() fails, gtp_encap_enable_socket() returns a
NULL pointer, but its callers only check for error pointers thus miss
the NULL pointer case.
Fix it by returning an error pointer with the error code carried from
sockfd_lookup().
(I found this bug during code inspection.)
Fixes: 1e3a3abd8b ("gtp: make GTP sockets in gtp_newlink optional")
Cc: Andreas Schultz <aschultz@tpip.net>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://patch.msgid.link/20240825191638.146748-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8af174ea86 upstream.
The mana_hwc_rx_event_handler() / mana_hwc_handle_resp() calls
complete(&ctx->comp_event) before posting the wqe back. It's
possible that other callers, like mana_create_txq(), start the
next round of mana_hwc_send_request() before the posting of wqe.
And if the HW is fast enough to respond, it can hit no_wqe error
on the HW channel, then the response message is lost. The mana
driver may fail to create queues and open, because of waiting for
the HW response and timed out.
Sample dmesg:
[ 528.610840] mana 39d4:00:02.0: HWC: Request timed out!
[ 528.614452] mana 39d4:00:02.0: Failed to send mana message: -110, 0x0
[ 528.618326] mana 39d4:00:02.0 enP14804s2: Failed to create WQ object: -110
To fix it, move posting of rx wqe before complete(&ctx->comp_event).
Cc: stable@vger.kernel.org
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27ec3c57fc upstream.
mwifiex_band_2ghz and mwifiex_band_5ghz are statically allocated, but
used and modified in driver instances. Duplicate them before using
them in driver instances so that different driver instances do not
influence each other.
This was observed on a board which has one PCIe and one SDIO mwifiex
adapter. It blew up in mwifiex_setup_ht_caps(). This was called with
the statically allocated struct which is modified in this function.
Cc: stable@vger.kernel.org
Fixes: d6bffe8bb5 ("mwifiex: support for creation of AP interface")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240809-mwifiex-duplicate-static-structs-v1-1-6837b903b1a4@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80a1e7b83b upstream.
It is done everywhere in cxgb4 code, e.g. in is_filter_exact_match()
There is no reason it should not be done here
Found by Linux Verification Center (linuxtesting.org) with SVACE
Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru>
Cc: stable@vger.kernel.org
Fixes: 12b276fbf6 ("cxgb4: add support to create hash filters")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240819075408.92378-1-kniv@yandex-team.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 797a68c9de ]
If a multicast address is removed but there are still some multicast
addresses, that address would remain programmed into the frame filter.
Fix this by explicitly setting the enable bit for each filter.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822154059.1066595-3-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ae738dfef ]
If promiscuous mode is disabled when there are fewer than four multicast
addresses, then it will not be reflected in the hardware. Fix this by
always clearing the promiscuous mode flag even when we program multicast
addresses.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822154059.1066595-2-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 528876d867 ]
If an ATU violation was caused by a CPU Load operation, the SPID could
be larger than DSA_MAX_PORTS (the size of mv88e6xxx_chip.ports[] array).
Fixes: 75c05a74e7 ("net: dsa: mv88e6xxx: Fix counting of ATU violations")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240819235251.1331763-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8646384d80 ]
In applications where the switch ports must perform 802.1X based
authentication and are therefore locked, ATU violation interrupts are
quite to be expected as part of normal operation. The problem is that
they currently spam the kernel log, even if rate limited.
Create a series of trace points, all derived from the same event class,
which log these violations to the kernel's trace buffer, which is both
much faster and much easier to ignore than printing to a serial console.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_atu_full_violation
mv88e6xxx:mv88e6xxx_atu_miss_violation
mv88e6xxx:mv88e6xxx_atu_member_violation
$ trace-cmd record -e mv88e6xxx sleep 10
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 528876d867 ("net: dsa: mv88e6xxx: Fix out-of-bound access")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bf24ad09b ]
When an ATU violation occurs, the switch uses the ATU FID register to
report the FID of the MAC address that incurred the violation. It would
be good for the driver to know the FID value for purposes such as
logging and CPU-based authentication.
Up until now, the driver has been calling the mv88e6xxx_g1_atu_op()
function to read ATU violations, but that doesn't do exactly what we
want, namely it calls mv88e6xxx_g1_atu_fid_write() with FID 0.
(side note, the documentation for the ATU Get/Clear Violation command
says that writes to the ATU FID register have no effect before the
operation starts, it's only that we disregard the value that this
register provides once the operation completes)
So mv88e6xxx_g1_atu_fid_write() is not what we want, but rather
mv88e6xxx_g1_atu_fid_read(). However, the latter doesn't exist, we need
to write it.
The remainder of mv88e6xxx_g1_atu_op() except for
mv88e6xxx_g1_atu_fid_write() is still needed, namely to send a
GET_CLR_VIOLATION command to the ATU. In principle we could have still
kept calling mv88e6xxx_g1_atu_op(), but the MDIO writes to the ATU FID
register are pointless, but in the interest of doing less CPU work per
interrupt, write a new function called mv88e6xxx_g1_read_atu_violation()
and call it.
The FID will be the port default FID as set by mv88e6xxx_port_set_fid()
if the VID from the packet cannot be found in the VTU. Otherwise it is
the FID derived from the VTU entry associated with that VID.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 528876d867 ("net: dsa: mv88e6xxx: Fix out-of-bound access")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c50e747596 ]
The dpaa2_switch_add_bufs() function returns the number of bufs that it
was able to add. It returns BUFS_PER_CMD (7) for complete success or a
smaller number if there are not enough pages available. However, the
error checking is looking at the total number of bufs instead of the
number which were added on this iteration. Thus the error checking
only works correctly for the first iteration through the loop and
subsequent iterations are always counted as a success.
Fix this by checking only the bufs added in the current iteration.
Fixes: 0b1b713704 ("staging: dpaa2-switch: handle Rx path on control interface")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/eec27f30-b43f-42b6-b8ee-04a6f83423b6@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4c5c5d2ef ]
If the active slave is cleared manually the xfrm state is not flushed.
This leads to xfrm add/del imbalance and adding the same state multiple
times. For example when the device cannot handle anymore states we get:
[ 1169.884811] bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA
because it's filled with the same state after multiple active slave
clearings. This change also has a few nice side effects: user-space
gets a notification for the change, the old device gets its mac address
and promisc/mcast adjusted properly.
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95c90e4ad8 ]
We must check if there is an active slave before dereferencing the pointer.
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc59b9a5f7 ]
Fix the return type which should be bool.
Fixes: 955b785ec6 ("bonding: fix suspicious RCU usage in bond_ipsec_offload_ok()")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58a63729c9 ]
After napi_complete_done() is called when NAPI is polling in the current
process context, another NAPI may be scheduled and start running in
softirq on another CPU and may ring the doorbell before the current CPU
does. When combined with unnecessary rings when there is no need to arm
the CQ, it triggers error paths in the hardware.
This patch fixes this by calling napi_complete_done() after doorbell
rings. It limits the number of unnecessary rings when there is
no need to arm. MANA hardware specifies that there must be one doorbell
ring every 8 CQ wraparounds. This driver guarantees one doorbell ring as
soon as the number of consumed CQEs exceeds 4 CQ wraparounds. In practical
workloads, the 4 CQ wraparounds proves to be big enough that it rarely
exceeds this limit before all the napi weight is consumed.
To implement this, add a per-CQ counter cq->work_done_since_doorbell,
and make sure the CQ is armed as soon as passing 4 wraparounds of the CQ.
Cc: stable@vger.kernel.org
Fixes: e1b5683ff6 ("net: mana: Move NAPI from EQ to CQ")
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Long Li <longli@microsoft.com>
Link: https://patch.msgid.link/1723219138-29887-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e2969a0d6 ]
Add checking for vf id of mailbox, in order to avoid array
out-of-bounds risk.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bea747f3f ]
Since NUM_XMIT_BUFFS is always 1, building m68k with sun3_defconfig and
-Warraybounds, this build warning is visible[1]:
drivers/net/ethernet/i825xx/sun3_82586.c: In function 'sun3_82586_timeout':
drivers/net/ethernet/i825xx/sun3_82586.c:990:122: warning: array subscript 1 is above array bounds of 'volatile struct transmit_cmd_struct *[1]' [-Warray-bounds=]
990 | printk("%s: command-stats: %04x %04x\n",dev->name,swab16(p->xmit_cmds[0]->cmd_status),swab16(p->xmit_cmds[1]->cmd_status));
| ~~~~~~~~~~~~^~~
...
drivers/net/ethernet/i825xx/sun3_82586.c:156:46: note: while referencing 'xmit_cmds'
156 | volatile struct transmit_cmd_struct *xmit_cmds[NUM_XMIT_BUFFS];
Avoid accessing index 1 since it doesn't exist.
Link: https://github.com/KSPP/linux/issues/325 [1]
Cc: Sam Creasey <sammy@sammy.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20240206161651.work.876-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 048449fc66 ]
During debugfs command handling transport function is used directly,
this bypasses the locking used by runtime operation function
and leads to a kernel warning when two commands are
sent in parallel.
Fix it by using runtime operations function when sending
debugfs command.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.4f80ac90658a.Ia1dfa1195c919f3002fe08db3eefbd2bfa921bbf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c6a0b1f0a ]
In RFKILL we first set the RFKILL bit, then we abort scan
(if one exists) by waiting for the notification from FW
and notifying mac80211. And then we stop the device.
But in case we have a scan ongoing in the period of time between
rfkill on and before the device is stopped - we will not wait for the
FW notification because of the iwl_mvm_is_radio_killed() condition,
and then the scan_status and uid_status are misconfigured,
(scan_status is cleared but uid_status not)
and when the notification suddenly arrives (before stopping the device)
we will get into the assert about scan_status and uid_status mismatch.
Fix this by waiting for FW notif when rfkill is on but the device isn't
disabled yet.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.c43b69aa2c77.Icc7b5efb47974d6f499156ff7510b786e177993b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7bcea9c27 ]
While converting struct ieee80211_tim_ie::virtual_map to be a flexible
array it was observed that the TIM IE processing in cw1200_rx_cb()
could potentially process a malformed IE in a manner that could result
in a buffer over-read. Add logic to verify that the TIM IE length is
large enough to hold a valid TIM payload before processing it.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831-ieee80211_tim_ie-v3-1-e10ff584ab5d@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be5e816d00 ]
When config TC during the reset process, may cause a deadlock, the flow is
as below:
pf reset start
│
▼
......
setup tc │
│ ▼
▼ DOWN: napi_disable()
napi_disable()(skip) │
│ │
▼ ▼
...... ......
│ │
▼ │
napi_enable() │
▼
UINIT: netif_napi_del()
│
▼
......
│
▼
INIT: netif_napi_add()
│
▼
...... global reset start
│ │
▼ ▼
UP: napi_enable()(skip) ......
│ │
▼ ▼
...... napi_disable()
In reset process, the driver will DOWN the port and then UINIT, in this
case, the setup tc process will UP the port before UINIT, so cause the
problem. Adds a DOWN process in UINIT to fix it.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8445d9d3c0 ]
Currently, if hns3 PF or VF FLR reset failed after five times retry,
the reset done process will directly release the semaphore
which has already released in hclge_reset_prepare_general.
This will cause down operation fail.
So this patch fixes it by adding reset state judgement. The up operation is
only called after successful PF FLR reset.
Fixes: 8627bdedc4 ("net: hns3: refactor the precedure of PF FLR")
Fixes: f28368bb45 ("net: hns3: refactor the procedure of VF FLR")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df934abb18 ]
A recent change to the driver exposed a bug where the MAC RX
filters (unicast MAC, broadcast MAC, and multicast MAC) are
configured and enabled before the RX path is fully initialized.
The result of this bug is that after the PHY is started packets
that match these MAC RX filters start to flow into the RX FIFO.
And then, after rx_init() is completed, these packets will go
into the driver RX ring as well. If enough packets are received
to fill the RX ring (default size is 128 packets) before the call
to request_irq() completes, the driver RX function becomes stuck.
This bug is intermittent but is most likely to be seen where the
oob_net0 interface is connected to a busy network with lots of
broadcast and multicast traffic.
All the MAC RX filters must be disabled until the RX path is ready,
i.e. all initialization is done and all the IRQs are installed.
Fixes: f7442a634a ("mlxbf_gige: call request_irq() after NAPI initialized")
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240809163612.12852-1-davthompson@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa63c6434b ]
The VSC73xx has a busy flag used during MDIO operations. It is raised
when MDIO read/write operations are in progress. Without it, PHYs are
misconfigured and bus operations do not work as expected.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb7e33d01d ]
Switch the delay loop during the Arbiter empty check from
vsc73xx_adjust_link() to use read_poll_timeout(). Functionally,
one msleep() call is eliminated at the end of the loop in the timeout
case.
As Russell King suggested:
"This [change] avoids the issue that on the last iteration, the code reads
the register, tests it, finds the condition that's being waiting for is
false, _then_ waits and end up printing the error message - that last
wait is rather useless, and as the arbiter state isn't checked after
waiting, it could be that we had success during the last wait."
Suggested-by: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://lore.kernel.org/r/20240417205048.3542839-2-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: fa63c6434b ("net: dsa: vsc73xx: check busy flag in MDIO operations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b9eebc2c7 ]
In the 'vsc73xx_phy_write' function, the register value is missing,
and the phy write operation always sends zeros.
This commit passes the value variable into the proper register.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ff2f816e2 ]
In axiethernet header fix register defines comment description to be
inline with IP documentation. It updates MAC configuration register,
MDIO configuration register and frame filter control description.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbc796be17 ]
Previously, an ethtool rx flow with no attrs would not be added to the
NIC as it has no rules to configure the hw with, but it would be
reported as successful to the caller (return code 0). This is confusing
for the user as ethtool then reports "Added rule $num", but no rule was
actually added.
This change corrects that by instead reporting these wrong rules as
-EINVAL.
Fixes: b29c61dac3 ("net/mlx5e: Ethtool steering flow validation refactoring")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20240808144107.2095424-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e037a26ead ]
Testing uncovered that even when the taprio gate is closed, some packets
still transmit.
According to i225/6 hardware errata [1], traffic might overflow the
planned QBV window. This happens because MAC maintains an internal buffer,
primarily for supporting half duplex retries. Therefore, even when the
gate closes, residual MAC data in the buffer may still transmit.
To mitigate this for i226, reduce the MAC's internal buffer from 192 bytes
to the recommended 88 bytes by modifying the RETX_CTL register value.
This follows guidelines from:
[1] Ethernet Controller I225/I22 Spec Update Rev 2.1 Errata Item 9:
TSN: Packet Transmission Might Cross Qbv Window
[2] I225/6 SW User Manual Rev 1.2.4: Section 8.11.5 Retry Buffer Control
Note that the RETX_CTL register can't be used in TSN mode because half
duplex feature cannot coexist with TSN.
Test Steps:
1. Send taprio cmd to board A:
tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 4 \
map 3 2 1 0 3 3 3 3 3 3 3 3 3 3 3 3 \
queues 1@0 1@1 1@2 1@3 \
base-time 0 \
sched-entry S 0x07 500000 \
sched-entry S 0x0f 500000 \
flags 0x2 \
txtime-delay 0
Note that for TC3, gate should open for 500us and close for another
500us.
3. Take tcpdump log on Board B.
4. Send udp packets via UDP tai app from Board A to Board B.
5. Analyze tcpdump log via wireshark log on Board B. Ensure that the
total time from the first to the last packet received during one cycle
for TC3 does not exceed 500us.
Fixes: 4354621173 ("igc: Add new device ID's")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8897dc54e ]
Remove the Qbv BaseTime restriction for I226 so that the BaseTime can be
scheduled to the future time. A new register bit of Tx Qav Control
(Bit-7: FutScdDis) was introduced to allow I226 scheduling future time as
Qbv BaseTime and not having the Tx hang timeout issue.
Besides, according to datasheet section 7.5.2.9.3.3, FutScdDis bit has to
be configured first before the cycle time and base time.
Indeed the FutScdDis bit is only active on re-configuration, thus we have
to set the BASET_L to zero and then only set it to the desired value.
Please also note that the Qbv configuration flow is moved around based on
the Qbv programming guideline that is documented in the latest datasheet.
Co-developed-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: e037a26ead ("igc: Fix packet still tx after gate close by reducing i226 MAC retry buffer")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 790835fcc0 ]
The launchtime offset should be corrected according to sections 7.5.2.6
Transmit Scheduling Latency of the Intel Ethernet I225/I226 Software
User Manual.
Software can compensate the latency between the transmission scheduling
and the time that packet is transmitted to the network by setting this
GTxOffset register. Without setting this register, there may be a
significant delay between the packet scheduling and the network point.
This patch helps to reduce the latency for each of the link speed.
Before:
10Mbps : 11000 - 13800 nanosecond
100Mbps : 1300 - 1700 nanosecond
1000Mbps : 190 - 600 nanosecond
2500Mbps : 1400 - 1700 nanosecond
After:
10Mbps : less than 750 nanosecond
100Mbps : less than 192 nanosecond
1000Mbps : less than 128 nanosecond
2500Mbps : less than 128 nanosecond
Test Setup:
Talker : Use l2_tai.c to generate the launchtime into packet payload.
Listener: Use timedump.c to compute the delta between packet arrival and
LaunchTime packet payload.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: e037a26ead ("igc: Fix packet still tx after gate close by reducing i226 MAC retry buffer")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f151c147b3 upstream
Enable the mac_managed_pm configuration in the phylink_config
structure to avoid the kernel warning during system resume.
Fixes: 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3862093ee ]
bcm_sf2_mdio_register() calls of_phy_find_device() and then
phy_device_remove() in a loop to remove existing PHY devices.
of_phy_find_device() eventually calls bus_find_device(), which calls
get_device() on the returned struct device * to increment the refcount.
The current implementation does not decrement the refcount, which causes
memory leak.
This commit adds the missing phy_device_free() call to decrement the
refcount via put_device() to balance the refcount.
Fixes: 771089c2a4 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240806011327.3817861-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 08f3a5c380 upstream.
It could lead to error happen because the variable res is not updated if
the call to sr_share_read_word returns an error. In this particular case
error code was returned and res stayed uninitialized. Same issue also
applies to sr_read_reg.
This can be avoided by checking the return value of sr_share_read_word
and sr_read_reg, and propagating the error if the read operation failed.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: c9b37458e9 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f8e82a020 ]
Since the documentation for mlx5_toggle_port_link states that it should
only be used after setting the port register, we add a check for the
return value from mlx5_port_set_eth_ptys to ensure the register was
successfully set before calling it.
Fixes: 667daedaec ("net/mlx5e: Toggle link only after modifying port parameters")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-9-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0aa3ca956c ]
This function has a nested loop. The problem is that both the inside
and outside loop use the same variable as an iterator. I found this
via static analysis so I'm not sure the impact. It could be that it
loops forever or, more likely, the loop exits early.
Fixes: 3a616b92a9 ("net: mvpp2: Add TX flow control support for jumbo frames")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/eaa8f403-7779-4d81-973d-a9ecddc0bf6f@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9dbebae2e ]
The perfect_match parameter of the update_vlan_hash operation is __le16,
and is correctly converted from host byte-order in the lone caller,
stmmac_vlan_update().
However, the implementations of this caller, dwxgmac2_update_vlan_hash()
and dwxgmac2_update_vlan_hash(), both treat this parameter as host byte
order, using the following pattern:
u32 value = ...
...
writel(value | perfect_match, ...);
This is not correct because both:
1) value is host byte order; and
2) writel expects a host byte order value as it's first argument
I believe that this will break on big endian systems. And I expect it
has gone unnoticed by only being exercised on little endian systems.
The approach taken by this patch is to update the callback, and it's
caller to simply use a host byte order value.
Flagged by Sparse.
Compile tested only.
Fixes: c7ab0b8088 ("net: stmmac: Fallback to VLAN Perfect filtering if HASH is not available")
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ba359c0cd ]
RCU use in bond_should_notify_peers() looks wrong, since it does
rcu_dereference(), leaves the critical section, and uses the
pointer after that.
Luckily, it's called either inside a nested RCU critical section
or with the RTNL held.
Annotate it with rcu_dereference_rtnl() instead, and remove the
inner RCU critical section.
Fixes: 4cb4f97b7e ("bonding: rebuild the lock use for bond_mii_monitor()")
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20240719094119.35c62455087d.I68eb9c0f02545b364b79a59f2110f2cf5682a8e2@changeid
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 36e3b949e3 upstream.
The NIC requires each TSO segment to not span more than 10
descriptors. NIC further requires each descriptor to not exceed
16KB - 1 (GVE_TX_MAX_BUF_SIZE_DQO).
The descriptors for an skb are generated by
gve_tx_add_skb_no_copy_dqo() for DQO RDA queue format.
gve_tx_add_skb_no_copy_dqo() loops through each skb frag and
generates a descriptor for the entire frag if the frag size is
not greater than GVE_TX_MAX_BUF_SIZE_DQO. If the frag size is
greater than GVE_TX_MAX_BUF_SIZE_DQO, it is split into descriptor(s)
of size GVE_TX_MAX_BUF_SIZE_DQO and a descriptor is generated for
the remainder (frag size % GVE_TX_MAX_BUF_SIZE_DQO).
gve_can_send_tso() checks if the descriptors thus generated for an
skb would meet the requirement that each TSO-segment not span more
than 10 descriptors. However, the current code misses an edge case
when a TSO segment spans multiple descriptors within a large frag.
This change fixes the edge case.
gve_can_send_tso() relies on the assumption that max gso size (9728)
is less than GVE_TX_MAX_BUF_SIZE_DQO and therefore within an skb
fragment a TSO segment can never span more than 2 descriptors.
Fixes: a57e5de476 ("gve: DQO: Add TX path")
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240724143431.3343722-1-pkaligineedi@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a17b9f590f upstream.
When changing the interface type we also need to update the bss_num, the
driver private data is searched based on a unique (bss_type, bss_num)
tuple, therefore every time bss_type changes, bss_num must also change.
This fixes for example an issue in which, after the mode changed, a
wireless scan on the changed interface would not finish, leading to
repeated -EBUSY messages to userspace when other scan requests were
sent.
Fixes: c606008b70 ("mwifiex: Properly initialize private structure on interface type changes")
Cc: stable@vger.kernel.org
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240510110458.15475-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97d9fba9a8 upstream.
Currently, netconsole cleans up the netpoll structure before disabling
the target. This approach can lead to race conditions, as message
senders (write_ext_msg() and write_msg()) check if the target is
enabled before using netpoll. The sender can validate that the target is
enabled, but, the netpoll might be de-allocated already, causing
undesired behaviours.
This patch reverses the order of operations:
1. Disable the target
2. Clean up the netpoll structure
This change eliminates the potential race condition, ensuring that
no messages are sent through a partially cleaned-up netpoll structure.
Fixes: 2382b15bcc ("netconsole: take care of NETDEV_UNREGISTER event")
Cc: stable@vger.kernel.org
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240712143415.1141039-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5118072e2 ]
Broadcom switches supported by the b53 driver use a chip-wide jumbo frame
configuration. In the commit referenced with the Fixes tag, the setting
is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient chip-wide maximum frame size for the CPU port.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports. This aligns the driver
to the behavior of other switch drivers.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
