[ Upstream commit 317e49358e ]
The devm_free_irq() and devm_request_irq() functions should not be
executed in an atomic context.
During device suspend, all userspace processes and most kernel threads
are frozen. Additionally, we flush all tx/rx status, disable all macb
interrupts, and halt rx operations. Therefore, it is safe to split the
region protected by bp->lock into two independent sections, allowing
devm_free_irq() and devm_request_irq() to run in a non-atomic context.
This modification resolves the following lockdep warning:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:591
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 501, name: rtcwake
preempt_count: 1, expected: 0
RCU nest depth: 1, expected: 0
7 locks held by rtcwake/501:
#0: ffff0008038c3408 (sb_writers#5){.+.+}-{0:0}, at: vfs_write+0xf8/0x368
#1: ffff0008049a5e88 (&of->mutex#2){+.+.}-{4:4}, at: kernfs_fop_write_iter+0xbc/0x1c8
#2: ffff00080098d588 (kn->active#70){.+.+}-{0:0}, at: kernfs_fop_write_iter+0xcc/0x1c8
#3: ffff800081c84888 (system_transition_mutex){+.+.}-{4:4}, at: pm_suspend+0x1ec/0x290
#4: ffff0008009ba0f8 (&dev->mutex){....}-{4:4}, at: device_suspend+0x118/0x4f0
#5: ffff800081d00458 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire+0x4/0x48
#6: ffff0008031fb9e0 (&bp->lock){-.-.}-{3:3}, at: macb_suspend+0x144/0x558
irq event stamp: 8682
hardirqs last enabled at (8681): [<ffff8000813c7d7c>] _raw_spin_unlock_irqrestore+0x44/0x88
hardirqs last disabled at (8682): [<ffff8000813c7b58>] _raw_spin_lock_irqsave+0x38/0x98
softirqs last enabled at (7322): [<ffff8000800f1b4c>] handle_softirqs+0x52c/0x588
softirqs last disabled at (7317): [<ffff800080010310>] __do_softirq+0x20/0x2c
CPU: 1 UID: 0 PID: 501 Comm: rtcwake Not tainted 7.0.0-rc3-next-20260310-yocto-standard+ #125 PREEMPT
Hardware name: ZynqMP ZCU102 Rev1.1 (DT)
Call trace:
show_stack+0x24/0x38 (C)
__dump_stack+0x28/0x38
dump_stack_lvl+0x64/0x88
dump_stack+0x18/0x24
__might_resched+0x200/0x218
__might_sleep+0x38/0x98
__mutex_lock_common+0x7c/0x1378
mutex_lock_nested+0x38/0x50
free_irq+0x68/0x2b0
devm_irq_release+0x24/0x38
devres_release+0x40/0x80
devm_free_irq+0x48/0x88
macb_suspend+0x298/0x558
device_suspend+0x218/0x4f0
dpm_suspend+0x244/0x3a0
dpm_suspend_start+0x50/0x78
suspend_devices_and_enter+0xec/0x560
pm_suspend+0x194/0x290
state_store+0x110/0x158
kobj_attr_store+0x1c/0x30
sysfs_kf_write+0xa8/0xd0
kernfs_fop_write_iter+0x11c/0x1c8
vfs_write+0x248/0x368
ksys_write+0x7c/0xf8
__arm64_sys_write+0x28/0x40
invoke_syscall+0x4c/0xe8
el0_svc_common+0x98/0xf0
do_el0_svc+0x28/0x40
el0_svc+0x54/0x1e0
el0t_64_sync_handler+0x84/0x130
el0t_64_sync+0x198/0x1a0
Fixes: 558e35ccfe ("net: macb: WoL support for GEM type of Ethernet controller")
Cc: stable@vger.kernel.org
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://patch.msgid.link/20260318-macb-irq-v2-1-f1179768ab24@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ adapted WoL register writes to use MACB_BIT(MAG) instead of tmp variable ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f4e090b9 upstream.
The jumbo_frm() chain-mode implementation unconditionally computes
len = nopaged_len - bmax;
where nopaged_len = skb_headlen(skb) (linear bytes only) and bmax is
BUF_SIZE_8KiB or BUF_SIZE_2KiB. However, the caller stmmac_xmit()
decides to invoke jumbo_frm() based on skb->len (total length including
page fragments):
is_jumbo = stmmac_is_jumbo_frm(priv, skb->len, enh_desc);
When a packet has a small linear portion (nopaged_len <= bmax) but a
large total length due to page fragments (skb->len > bmax), the
subtraction wraps as an unsigned integer, producing a huge len value
(~0xFFFFxxxx). This causes the while (len != 0) loop to execute
hundreds of thousands of iterations, passing skb->data + bmax * i
pointers far beyond the skb buffer to dma_map_single(). On IOMMU-less
SoCs (the typical deployment for stmmac), this maps arbitrary kernel
memory to the DMA engine, constituting a kernel memory disclosure and
potential memory corruption from hardware.
Fix this by introducing a buf_len local variable clamped to
min(nopaged_len, bmax). Computing len = nopaged_len - buf_len is then
always safe: it is zero when the linear portion fits within a single
descriptor, causing the while (len != 0) loop to be skipped naturally,
and the fragment loop in stmmac_xmit() handles page fragments afterward.
Fixes: 286a837217 ("stmmac: add CHAINED descriptor mode support (V4)")
Cc: stable@vger.kernel.org
Signed-off-by: Tyllis Xu <LivelyCarpet87@gmail.com>
Link: https://patch.msgid.link/20260401044708.1386919-1-LivelyCarpet87@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b76254c55d upstream.
qca_tty_receive() consumes each input byte before checking whether a
completed frame needs a fresh receive skb. When the current byte completes
a frame, the driver delivers that frame and then allocates a new skb for
the next one.
If that allocation fails, the current code returns i even though data[i]
has already been consumed and may already have completed the delivered
frame. Since serdev interprets the return value as the number of accepted
bytes, this under-reports progress by one byte and can replay the final
byte of the completed frame into a fresh parser state on the next call.
Return i + 1 in that failure path so the accepted-byte count matches the
actual receive-state progress.
Fixes: dfc768fbe6 ("net: qualcomm: add QCA7000 UART driver")
Cc: stable@vger.kernel.org
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260402071207.4036-1-pengpeng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dede39676 upstream.
When dma_map_single() fails in tse_start_xmit(), the function returns
NETDEV_TX_OK without freeing the skb. Since NETDEV_TX_OK tells the
stack the packet was consumed, the skb is never freed, leaking memory
on every DMA mapping failure.
Add dev_kfree_skb_any() before returning to properly free the skb.
Fixes: bbd2190ce9 ("Altera TSE: Add main and header file for Altera Ethernet Driver")
Cc: stable@vger.kernel.org
Signed-off-by: David Carlier <devnexen@gmail.com>
Link: https://patch.msgid.link/20260401211218.279185-1-devnexen@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12cd763275 upstream.
dma_alloc_consistent() may change the size to align it. The new size is
saved in alloced.
Change the free size to match the allocation size.
Fixes: 5b435de0d7 ("net: wireless: add brcm80211 drivers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260218130741.46566-3-fourier.thomas@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25369b2222 upstream.
USB drivers bind to USB interfaces and any device managed resources
should have their lifetime tied to the interface rather than parent USB
device. This avoids issues like memory leaks when drivers are unbound
without their devices being physically disconnected (e.g. on probe
deferral or configuration changes).
Fix the USB anchor lifetime so that it is released on driver unbind.
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Cc: stable@vger.kernel.org # 4.7
Cc: Vishal Thanki <vishalthanki@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20260327113219.1313748-1-johan@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 789b06f9f3 upstream.
Currently we execute `SET_NETDEV_DEV(dev, &priv->lowerdev->dev)` for
the virt_wifi net devices. However, unregistering a virt_wifi device in
netdev_run_todo() can happen together with the device referenced by
SET_NETDEV_DEV().
It can result in use-after-free during the ethtool operations performed
on a virt_wifi device that is currently being unregistered. Such a net
device can have the `dev.parent` field pointing to the freed memory,
but ethnl_ops_begin() calls `pm_runtime_get_sync(dev->dev.parent)`.
Let's remove SET_NETDEV_DEV for virt_wifi to avoid bugs like this:
==================================================================
BUG: KASAN: slab-use-after-free in __pm_runtime_resume+0xe2/0xf0
Read of size 2 at addr ffff88810cfc46f8 by task pm/606
Call Trace:
<TASK>
dump_stack_lvl+0x4d/0x70
print_report+0x170/0x4f3
? __pfx__raw_spin_lock_irqsave+0x10/0x10
kasan_report+0xda/0x110
? __pm_runtime_resume+0xe2/0xf0
? __pm_runtime_resume+0xe2/0xf0
__pm_runtime_resume+0xe2/0xf0
ethnl_ops_begin+0x49/0x270
ethnl_set_features+0x23c/0xab0
? __pfx_ethnl_set_features+0x10/0x10
? kvm_sched_clock_read+0x11/0x20
? local_clock_noinstr+0xf/0xf0
? local_clock+0x10/0x30
? kasan_save_track+0x25/0x60
? __kasan_kmalloc+0x7f/0x90
? genl_family_rcv_msg_attrs_parse.isra.0+0x150/0x2c0
genl_family_rcv_msg_doit+0x1e7/0x2c0
? __pfx_genl_family_rcv_msg_doit+0x10/0x10
? __pfx_cred_has_capability.isra.0+0x10/0x10
? stack_trace_save+0x8e/0xc0
genl_rcv_msg+0x411/0x660
? __pfx_genl_rcv_msg+0x10/0x10
? __pfx_ethnl_set_features+0x10/0x10
netlink_rcv_skb+0x121/0x380
? __pfx_genl_rcv_msg+0x10/0x10
? __pfx_netlink_rcv_skb+0x10/0x10
? __pfx_down_read+0x10/0x10
genl_rcv+0x23/0x30
netlink_unicast+0x60f/0x830
? __pfx_netlink_unicast+0x10/0x10
? __pfx___alloc_skb+0x10/0x10
netlink_sendmsg+0x6ea/0xbc0
? __pfx_netlink_sendmsg+0x10/0x10
? __futex_queue+0x10b/0x1f0
____sys_sendmsg+0x7a2/0x950
? copy_msghdr_from_user+0x26b/0x430
? __pfx_____sys_sendmsg+0x10/0x10
? __pfx_copy_msghdr_from_user+0x10/0x10
___sys_sendmsg+0xf8/0x180
? __pfx____sys_sendmsg+0x10/0x10
? __pfx_futex_wait+0x10/0x10
? fdget+0x2e4/0x4a0
__sys_sendmsg+0x11f/0x1c0
? __pfx___sys_sendmsg+0x10/0x10
do_syscall_64+0xe2/0x570
? exc_page_fault+0x66/0xb0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
This fix may be combined with another one in the ethtool subsystem:
https://lore.kernel.org/all/20260322075917.254874-1-alex.popov@linux.com/T/#u
Fixes: d43c65b05b ("ethtool: runtime-resume netdev parent in ethnl_ops_begin")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20260324224607.374327-1-alex.popov@linux.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 494fc029f6 ]
Sinc commit 79a6d1bfe1 ("can: gs_usb: gs_usb_receive_bulk_callback():
unanchor URL on usb_submit_urb() error") a failing resubmit URB will print
an info message.
In the case of a short read where netdev has not yet been assigned,
initialize as NULL to avoid dereferencing an undefined value. Also report
the error value of the failed resubmit.
Fixes: 79a6d1bfe1 ("can: gs_usb: gs_usb_receive_bulk_callback(): unanchor URL on usb_submit_urb() error")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/all/20260119181904.1209979-1-kuba@kernel.org/
Link: https://patch.msgid.link/20260120-gs_usb-fix-error-message-v1-1-6be04de572bc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ruohan Lan <ruohanlan@aliyun.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79a6d1bfe1 ]
In commit 7352e1d593 ("can: gs_usb: gs_usb_receive_bulk_callback(): fix
URB memory leak"), the URB was re-anchored before usb_submit_urb() in
gs_usb_receive_bulk_callback() to prevent a leak of this URB during
cleanup.
However, this patch did not take into account that usb_submit_urb() could
fail. The URB remains anchored and
usb_kill_anchored_urbs(&parent->rx_submitted) in gs_can_close() loops
infinitely since the anchor list never becomes empty.
To fix the bug, unanchor the URB when an usb_submit_urb() error occurs,
also print an info message.
Fixes: 7352e1d593 ("can: gs_usb: gs_usb_receive_bulk_callback(): fix URB memory leak")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/all/20260110223836.3890248-1-kuba@kernel.org/
Link: https://patch.msgid.link/20260116-can_usb-fix-reanchor-v1-1-9d74e7289225@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ruohan Lan <ruohanlan@aliyun.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7352e1d593 ]
In gs_can_open(), the URBs for USB-in transfers are allocated, added to the
parent->rx_submitted anchor and submitted. In the complete callback
gs_usb_receive_bulk_callback(), the URB is processed and resubmitted. In
gs_can_close() the URBs are freed by calling
usb_kill_anchored_urbs(parent->rx_submitted).
However, this does not take into account that the USB framework unanchors
the URB before the complete function is called. This means that once an
in-URB has been completed, it is no longer anchored and is ultimately not
released in gs_can_close().
Fix the memory leak by anchoring the URB in the
gs_usb_receive_bulk_callback() to the parent->rx_submitted anchor.
[ The variable usbcan was renamed to parent in
commit b6980ad3a9 ("can: gs_usb: uniformly use "parent" as variable name for struct gs_usb")
introduced in v6.6. To backport to v5.15, replace parent with usbcan. ]
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260105-gs_usb-fix-memory-leak-v2-1-cc6ed6438034@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ruohan Lan <ruohanlan@aliyun.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c0fd0fe745 upstream.
ftgmac100_alloc_rings() allocates rx_skbs, tx_skbs, rxdes, txdes, and
rx_scratch in stages. On intermediate failures it returned -ENOMEM
directly, leaking resources allocated earlier in the function.
Rework the failure path to use staged local unwind labels and free
allocated resources in reverse order before returning -ENOMEM. This
matches common netdev allocation cleanup style.
Fixes: d72e01a043 ("ftgmac100: Use a scratch buffer for failed RX allocations")
Cc: stable@vger.kernel.org
Signed-off-by: Yufan Chen <yufan.chen@linux.dev>
Link: https://patch.msgid.link/20260328163257.60836-1-yufan.chen@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afa9a05e6c upstream.
vxlan_na_create() walks ND options according to option-provided
lengths. A malformed option can make the parser advance beyond the
computed option span or use a too-short source LLADDR option payload.
Validate option lengths against the remaining NS option area before
advancing, and only read source LLADDR when the option is large enough
for an Ethernet address.
Fixes: 4b29dba9c0 ("vxlan: fix nonfunctional neigh_reduce()")
Cc: stable@vger.kernel.org
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Tested-by: Ao Zhou <n05ec@lzu.edu.cn>
Co-developed-by: Yuan Tan <tanyuan98@outlook.com>
Signed-off-by: Yuan Tan <tanyuan98@outlook.com>
Suggested-by: Xin Liu <bird@lzu.edu.cn>
Signed-off-by: Yang Yang <n05ec@lzu.edu.cn>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260326034441.2037420-4-n05ec@lzu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d049e56b17 upstream.
The variable valuesize is declared as u8 but accumulates the total
length of all SSIDs to scan. Each SSID contributes up to 33 bytes
(IEEE80211_MAX_SSID_LEN + 1), and with WILC_MAX_NUM_PROBED_SSID (10)
SSIDs the total can reach 330, which wraps around to 74 when stored
in a u8.
This causes kmalloc to allocate only 75 bytes while the subsequent
memcpy writes up to 331 bytes into the buffer, resulting in a 256-byte
heap buffer overflow.
Widen valuesize from u8 to u32 to accommodate the full range.
Fixes: c5c77ba18e ("staging: wilc1000: Add SDIO/SPI 802.11 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Yasuaki Torimaru <yasuakitorimaru@gmail.com>
Link: https://patch.msgid.link/20260324100624.983458-1-yasuakitorimaru@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10dc35f6a4 ]
Avoid printing the misleading "kernel answers: No data available" devlink
output when querying firmware or pending firmware version fails
(e.g. MLX5 fw state errors / flash failures).
FW can fail on loading the pending flash image and get its version due
to various reasons, examples:
mlxfw: Firmware flash failed: key not applicable, err (7)
mlx5_fw_image_pending: can't read pending fw version while fw state is 1
and the resulting:
$ devlink dev info
kernel answers: No data available
Instead, just report 0 or 0xfff.. versions in case of failure to indicate
a problem, and let other information be shown.
after the fix:
$ devlink dev info
pci/0000:00:06.0:
driver mlx5_core
serial_number xxx...
board.serial_number MT2225300179
versions:
fixed:
fw.psid MT_0000000436
running:
fw.version 22.41.0188
fw 22.41.0188
stored:
fw.version 255.255.65535
fw 255.255.65535
Fixes: 9c86b07e30 ("net/mlx5: Added fw version query command")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260330194015.53585-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0f367a4f4 ]
The additional resources allocated with clk_register_fixed_rate() need
to be released with clk_unregister_fixed_rate(), otherwise they are lost.
Fixes: 83a77e9ec4 ("net: macb: Added PCI wrapper for Platform Driver.")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Link: https://patch.msgid.link/20260330184542.626619-2-pchelkin@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce8fe5287b ]
platform_device_unregister() may still want to use the registered clks
during runtime resume callback.
Note that there is a commit d82d5303c4 ("net: macb: fix use after free
on rmmod") that addressed the similar problem of clk vs platform device
unregistration but just moved the bug to another place.
Save the pointers to clks into local variables for reuse after platform
device is unregistered.
BUG: KASAN: use-after-free in clk_prepare+0x5a/0x60
Read of size 8 at addr ffff888104f85e00 by task modprobe/597
CPU: 2 PID: 597 Comm: modprobe Not tainted 6.1.164+ #114
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.1-0-g3208b098f51a-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xba
print_report+0x17f/0x496
kasan_report+0xd9/0x180
clk_prepare+0x5a/0x60
macb_runtime_resume+0x13d/0x410 [macb]
pm_generic_runtime_resume+0x97/0xd0
__rpm_callback+0xc8/0x4d0
rpm_callback+0xf6/0x230
rpm_resume+0xeeb/0x1a70
__pm_runtime_resume+0xb4/0x170
bus_remove_device+0x2e3/0x4b0
device_del+0x5b3/0xdc0
platform_device_del+0x4e/0x280
platform_device_unregister+0x11/0x50
pci_device_remove+0xae/0x210
device_remove+0xcb/0x180
device_release_driver_internal+0x529/0x770
driver_detach+0xd4/0x1a0
bus_remove_driver+0x135/0x260
driver_unregister+0x72/0xb0
pci_unregister_driver+0x26/0x220
__do_sys_delete_module+0x32e/0x550
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
</TASK>
Allocated by task 519:
kasan_save_stack+0x2c/0x50
kasan_set_track+0x21/0x30
__kasan_kmalloc+0x8e/0x90
__clk_register+0x458/0x2890
clk_hw_register+0x1a/0x60
__clk_hw_register_fixed_rate+0x255/0x410
clk_register_fixed_rate+0x3c/0xa0
macb_probe+0x1d8/0x42e [macb_pci]
local_pci_probe+0xd7/0x190
pci_device_probe+0x252/0x600
really_probe+0x255/0x7f0
__driver_probe_device+0x1ee/0x330
driver_probe_device+0x4c/0x1f0
__driver_attach+0x1df/0x4e0
bus_for_each_dev+0x15d/0x1f0
bus_add_driver+0x486/0x5e0
driver_register+0x23a/0x3d0
do_one_initcall+0xfd/0x4d0
do_init_module+0x18b/0x5a0
load_module+0x5663/0x7950
__do_sys_finit_module+0x101/0x180
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Freed by task 597:
kasan_save_stack+0x2c/0x50
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x50
__kasan_slab_free+0x106/0x180
__kmem_cache_free+0xbc/0x320
clk_unregister+0x6de/0x8d0
macb_remove+0x73/0xc0 [macb_pci]
pci_device_remove+0xae/0x210
device_remove+0xcb/0x180
device_release_driver_internal+0x529/0x770
driver_detach+0xd4/0x1a0
bus_remove_driver+0x135/0x260
driver_unregister+0x72/0xb0
pci_unregister_driver+0x26/0x220
__do_sys_delete_module+0x32e/0x550
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Fixes: d82d5303c4 ("net: macb: fix use after free on rmmod")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Link: https://patch.msgid.link/20260330184542.626619-1-pchelkin@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 393e0b4f17 ]
The XAXIDMA_BD_CTRL_LENGTH_MASK and XAXIDMA_BD_STS_ACTUAL_LEN_MASK
macros were defined as 0x007FFFFF (23 bits), but the AXI DMA IP
product guide (PG021) specifies the buffer length field as bits 25:0
(26 bits). Update both masks to match the IP documentation.
In practice this had no functional impact, since Ethernet frames are
far smaller than 2^23 bytes and the extra bits were always zero, but
the masks should still reflect the hardware specification.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Suraj Gupta <suraj.gupta2@amd.com>
Reviewed-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20260327073238.134948-2-suraj.gupta2@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb417456c7 ]
When driver signals carrier up via netif_carrier_on() its internal
link_up state isn't updated immediately. This leads to inconsistent
speed/duplex in /proc/net/bonding/bondX where the speed and duplex
is shown as unknown while ethtool shows correct values. Fix this by
using netif_carrier_ok() for link checking in get_ksettings function.
Fixes: 84421b99ce ("tg3: Update link_up flag for phylib devices")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ba8bda9a08 upstream.
A UAF issue occurs when the virtio_net driver is configured with napi_tx=N
and the device's IFF_XMIT_DST_RELEASE flag is cleared
(e.g., during the configuration of tc route filter rules).
When IFF_XMIT_DST_RELEASE is removed from the net_device, the network stack
expects the driver to hold the reference to skb->dst until the packet
is fully transmitted and freed. In virtio_net with napi_tx=N,
skbs may remain in the virtio transmit ring for an extended period.
If the network namespace is destroyed while these skbs are still pending,
the corresponding dst_ops structure has freed. When a subsequent packet
is transmitted, free_old_xmit() is triggered to clean up old skbs.
It then calls dst_release() on the skb associated with the stale dst_entry.
Since the dst_ops (referenced by the dst_entry) has already been freed,
a UAF kernel paging request occurs.
fix it by adds skb_dst_drop(skb) in start_xmit to explicitly release
the dst reference before the skb is queued in virtio_net.
Call Trace:
Unable to handle kernel paging request at virtual address ffff80007e150000
CPU: 2 UID: 0 PID: 6236 Comm: ping Kdump: loaded Not tainted 7.0.0-rc1+ #6 PREEMPT
...
percpu_counter_add_batch+0x3c/0x158 lib/percpu_counter.c:98 (P)
dst_release+0xe0/0x110 net/core/dst.c:177
skb_release_head_state+0xe8/0x108 net/core/skbuff.c:1177
sk_skb_reason_drop+0x54/0x2d8 net/core/skbuff.c:1255
dev_kfree_skb_any_reason+0x64/0x78 net/core/dev.c:3469
napi_consume_skb+0x1c4/0x3a0 net/core/skbuff.c:1527
__free_old_xmit+0x164/0x230 drivers/net/virtio_net.c:611 [virtio_net]
free_old_xmit drivers/net/virtio_net.c:1081 [virtio_net]
start_xmit+0x7c/0x530 drivers/net/virtio_net.c:3329 [virtio_net]
...
Reproduction Steps:
NETDEV="enp3s0"
config_qdisc_route_filter() {
tc qdisc del dev $NETDEV root
tc qdisc add dev $NETDEV root handle 1: prio
tc filter add dev $NETDEV parent 1:0 \
protocol ip prio 100 route to 100 flowid 1:1
ip route add 192.168.1.100/32 dev $NETDEV realm 100
}
test_ns() {
ip netns add testns
ip link set $NETDEV netns testns
ip netns exec testns ifconfig $NETDEV 10.0.32.46/24
ip netns exec testns ping -c 1 10.0.32.1
ip netns del testns
}
config_qdisc_route_filter
test_ns
sleep 2
test_ns
Fixes: f2fc6a5458 ("[NETNS][IPV6] route6 - move ip6_dst_ops inside the network namespace")
Cc: stable@vger.kernel.org
Signed-off-by: xietangxin <xietangxin@yeah.net>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Fixes: 0287587884 ("net: better IFF_XMIT_DST_RELEASE support")
Link: https://patch.msgid.link/20260312025406.15641-1-xietangxin@yeah.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 72d96e4e24 ]
There's a potential mismatch between the memory reserved for statistics
and the amount of memory written.
gem_get_sset_count() correctly computes the number of stats based on the
active queues, whereas gem_get_ethtool_stats() indiscriminately copies
data using the maximum number of queues, and in the case the number of
active queues is less than MACB_MAX_QUEUES, this results in a OOB write
as observed in the KASAN splat.
==================================================================
BUG: KASAN: vmalloc-out-of-bounds in gem_get_ethtool_stats+0x54/0x78
[macb]
Write of size 760 at addr ffff80008080b000 by task ethtool/1027
CPU: [...]
Tainted: [E]=UNSIGNED_MODULE
Hardware name: raspberrypi rpi/rpi, BIOS 2025.10 10/01/2025
Call trace:
show_stack+0x20/0x38 (C)
dump_stack_lvl+0x80/0xf8
print_report+0x384/0x5e0
kasan_report+0xa0/0xf0
kasan_check_range+0xe8/0x190
__asan_memcpy+0x54/0x98
gem_get_ethtool_stats+0x54/0x78 [macb
926c13f3af83b0c6fe64badb21ec87d5e93fcf65]
dev_ethtool+0x1220/0x38c0
dev_ioctl+0x4ac/0xca8
sock_do_ioctl+0x170/0x1d8
sock_ioctl+0x484/0x5d8
__arm64_sys_ioctl+0x12c/0x1b8
invoke_syscall+0xd4/0x258
el0_svc_common.constprop.0+0xb4/0x240
do_el0_svc+0x48/0x68
el0_svc+0x40/0xf8
el0t_64_sync_handler+0xa0/0xe8
el0t_64_sync+0x1b0/0x1b8
The buggy address belongs to a 1-page vmalloc region starting at
0xffff80008080b000 allocated at dev_ethtool+0x11f0/0x38c0
The buggy address belongs to the physical page:
page: refcount:1 mapcount:0 mapping:0000000000000000
index:0xffff00000a333000 pfn:0xa333
flags: 0x7fffc000000000(node=0|zone=0|lastcpupid=0x1ffff)
raw: 007fffc000000000 0000000000000000 dead000000000122 0000000000000000
raw: ffff00000a333000 0000000000000000 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff80008080b080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff80008080b100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff80008080b180: 00 00 00 00 00 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
^
ffff80008080b200: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffff80008080b280: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
==================================================================
Fix it by making sure the copied size only considers the active number of
queues.
Fixes: 512286bbd4 ("net: macb: Added some queue statistics")
Signed-off-by: Paolo Valerio <pvalerio@redhat.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260323191634.2185840-1-pvalerio@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70b439bf06 ]
Currently, enetc_get_ringparam() only provides rx_pending and tx_pending,
but 'ethtool --show-ring' no longer displays these fields. Because the
ringparam retrieval path has moved to the new netlink interface, where
rings_fill_reply() emits the *x_pending only if the *x_max_pending values
are non-zero. So rx_max_pending and tx_max_pending to are added to
enetc_get_ringparam() to fix the issue.
Note that the maximum tx/rx ring size of hardware is 64K, but we haven't
added set_ringparam() to make the ring size configurable. To avoid users
mistakenly believing that the ring size can be increased, so set
the *x_max_pending to priv->*x_bd_count.
Fixes: e4a1717b67 ("ethtool: provide ring sizes with RINGS_GET request")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260320094222.706339-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbcb3cfcdc ]
The use of IONIC_CMD_LIF_SETATTR in the MAC address update path causes
the ionic firmware to update the LIF's identity in its persistent state.
Since the firmware state is maintained across host warm boots and driver
reloads, any MAC change on the Physical Function (PF) becomes "sticky.
This is problematic because it causes ethtool -P to report the
user-configured MAC as the permanent factory address, which breaks
system management tools that rely on a stable hardware identity.
While Virtual Functions (VFs) need this hardware-level programming to
properly handle MAC assignments in guest environments, the PF should
maintain standard transient behavior. This patch gates the
ionic_program_mac call using is_virtfn so that PF MAC changes remain
local to the netdev filters and do not overwrite the firmware's
permanent identity block.
Fixes: 19058be7c4 ("ionic: VF initial random MAC address if no assigned mac")
Signed-off-by: Mohammad Heib <mheib@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Link: https://patch.msgid.link/20260317170806.35390-1-mheib@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15fba71533 ]
The TRENDnet TUC-ET2G is a RTL8156 based usb ethernet adapter. Add its
vendor and product IDs.
Signed-off-by: Valentin Spreckels <valentin@spreckels.dev>
Link: https://patch.msgid.link/20260226195409.7891-2-valentin@spreckels.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b487318496 ]
Smatch reports:
drivers/net/dsa/bcm_sf2.c:997 bcm_sf2_sw_resume() warn:
'priv->clk' from clk_prepare_enable() not released on lines: 983,990.
The clock enabled by clk_prepare_enable() in bcm_sf2_sw_resume()
is not released if bcm_sf2_sw_rst() or bcm_sf2_cfp_resume() fails.
Add the missing clk_disable_unprepare() calls in the error paths
to properly release the clock resource.
Fixes: e9ec5c3bd2 ("net: dsa: bcm_sf2: request and handle clocks")
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Anas Iqbal <mohd.abd.6602@gmail.com>
Link: https://patch.msgid.link/20260318084212.1287-1-mohd.abd.6602@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a63baadf0 ]
mvpp2_bm_switch_buffers() unconditionally calls
mvpp2_bm_pool_update_priv_fc() when switching between per-cpu and
shared buffer pool modes. This function programs CM3 flow control
registers via mvpp2_cm3_read()/mvpp2_cm3_write(), which dereference
priv->cm3_base without any NULL check.
When the CM3 SRAM resource is not present in the device tree (the
third reg entry added by commit 60523583b0 ("dts: marvell: add CM3
SRAM memory to cp11x ethernet device tree")), priv->cm3_base remains
NULL and priv->global_tx_fc is false. Any operation that triggers
mvpp2_bm_switch_buffers(), for example an MTU change that crosses
the jumbo frame threshold, will crash:
Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000000
Mem abort info:
ESR = 0x0000000096000006
EC = 0x25: DABT (current EL), IL = 32 bits
pc : readl+0x0/0x18
lr : mvpp2_cm3_read.isra.0+0x14/0x20
Call trace:
readl+0x0/0x18
mvpp2_bm_pool_update_fc+0x40/0x12c
mvpp2_bm_pool_update_priv_fc+0x94/0xd8
mvpp2_bm_switch_buffers.isra.0+0x80/0x1c0
mvpp2_change_mtu+0x140/0x380
__dev_set_mtu+0x1c/0x38
dev_set_mtu_ext+0x78/0x118
dev_set_mtu+0x48/0xa8
dev_ifsioc+0x21c/0x43c
dev_ioctl+0x2d8/0x42c
sock_ioctl+0x314/0x378
Every other flow control call site in the driver already guards
hardware access with either priv->global_tx_fc or port->tx_fc.
mvpp2_bm_switch_buffers() is the only place that omits this check.
Add the missing priv->global_tx_fc guard to both the disable and
re-enable calls in mvpp2_bm_switch_buffers(), consistent with the
rest of the driver.
Fixes: 3a616b92a9 ("net: mvpp2: Add TX flow control support for jumbo frames")
Signed-off-by: Muhammad Hammad Ijaz <mhijaz@amazon.com>
Reviewed-by: Gunnar Kudrjavets <gunnarku@amazon.com>
Link: https://patch.msgid.link/20260316193157.65748-1-mhijaz@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34b11cc56e ]
If hardware doesn't support RX Flow Filters, rx_fs_lock spinlock is not
initialized leading to the following assertion splat triggerable via
set_rxnfc callback.
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 1 PID: 949 Comm: syz.0.6 Not tainted 6.1.164+ #113
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.1-0-g3208b098f51a-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x8d/0xba lib/dump_stack.c:106
assign_lock_key kernel/locking/lockdep.c:974 [inline]
register_lock_class+0x141b/0x17f0 kernel/locking/lockdep.c:1287
__lock_acquire+0x74f/0x6c40 kernel/locking/lockdep.c:4928
lock_acquire kernel/locking/lockdep.c:5662 [inline]
lock_acquire+0x190/0x4b0 kernel/locking/lockdep.c:5627
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x33/0x50 kernel/locking/spinlock.c:162
gem_del_flow_filter drivers/net/ethernet/cadence/macb_main.c:3562 [inline]
gem_set_rxnfc+0x533/0xac0 drivers/net/ethernet/cadence/macb_main.c:3667
ethtool_set_rxnfc+0x18c/0x280 net/ethtool/ioctl.c:961
__dev_ethtool net/ethtool/ioctl.c:2956 [inline]
dev_ethtool+0x229c/0x6290 net/ethtool/ioctl.c:3095
dev_ioctl+0x637/0x1070 net/core/dev_ioctl.c:510
sock_do_ioctl+0x20d/0x2c0 net/socket.c:1215
sock_ioctl+0x577/0x6d0 net/socket.c:1320
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x18c/0x210 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:46 [inline]
do_syscall_64+0x35/0x80 arch/x86/entry/common.c:76
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
A more straightforward solution would be to always initialize rx_fs_lock,
just like rx_fs_list. However, in this case the driver set_rxnfc callback
would return with a rather confusing error code, e.g. -EINVAL. So deny
set_rxnfc attempts directly if the RX filtering feature is not supported
by hardware.
Fixes: ae8223de3d ("net: macb: Added support for RX filtering")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Link: https://patch.msgid.link/20260316103826.74506-2-pchelkin@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit deb353d9bb ]
Since upstream commit e75665dd09 ("wifi: wlcore: ensure skb headroom
before skb_push"), wl1271_tx_allocate() and with it
wl1271_prepare_tx_frame() returns -EAGAIN if pskb_expand_head() fails.
However, in wlcore_tx_work_locked(), a return value of -EAGAIN from
wl1271_prepare_tx_frame() is interpreted as the aggregation buffer being
full. This causes the code to flush the buffer, put the skb back at the
head of the queue, and immediately retry the same skb in a tight while
loop.
Because wlcore_tx_work_locked() holds wl->mutex, and the retry happens
immediately with GFP_ATOMIC, this will result in an infinite loop and a
CPU soft lockup. Return -ENOMEM instead so the packet is dropped and
the loop terminates.
The problem was found by an experimental code review agent based on
gemini-3.1-pro while reviewing backports into v6.18.y.
Assisted-by: Gemini:gemini-3.1-pro
Fixes: e75665dd09 ("wifi: wlcore: ensure skb headroom before skb_push")
Cc: Peter Astrand <astrand@lysator.liu.se>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://patch.msgid.link/20260318064636.3065925-1-linux@roeck-us.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ffba24665 ]
igc_xmit_frame() misses updating skb->tail when the packet size is
shorter than the minimum one.
Use skb_put_padto() in alignment with other Intel Ethernet drivers.
Fixes: 0507ef8a03 ("igc: Add transmit and receive fastpath and interrupt handlers")
Signed-off-by: Kohei Enju <kohei@enjuk.jp>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 069c8f5aeb ]
syzbot reports "task hung in rpm_resume"
This is caused by aqc111_suspend calling
the PM variant of its write_cmd routine.
The simplified call trace looks like this:
rpm_suspend()
usb_suspend_both() - here udev->dev.power.runtime_status == RPM_SUSPENDING
aqc111_suspend() - called for the usb device interface
aqc111_write32_cmd()
usb_autopm_get_interface()
pm_runtime_resume_and_get()
rpm_resume() - here we call rpm_resume() on our parent
rpm_resume() - Here we wait for a status change that will never happen.
At this point we block another task which holds
rtnl_lock and locks up the whole networking stack.
Fix this by replacing the write_cmd calls with their _nopm variants
Reported-by: syzbot+48dc1e8dfc92faf1124c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=48dc1e8dfc92faf1124c
Fixes: e58ba4544c ("net: usb: aqc111: Add support for wake on LAN by MAGIC packet")
Signed-off-by: Nikola Z. Ivanov <zlatistiv@gmail.com>
Link: https://patch.msgid.link/20260313141643.1181386-1-zlatistiv@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa103fc8f5 ]
A potential race condition exists in mana_hwc_destroy_channel() where
hwc->caller_ctx is freed before the HWC's Completion Queue (CQ) and
Event Queue (EQ) are destroyed. This allows an in-flight CQ interrupt
handler to dereference freed memory, leading to a use-after-free or
NULL pointer dereference in mana_hwc_handle_resp().
mana_smc_teardown_hwc() signals the hardware to stop but does not
synchronize against IRQ handlers already executing on other CPUs. The
IRQ synchronization only happens in mana_hwc_destroy_cq() via
mana_gd_destroy_eq() -> mana_gd_deregister_irq(). Since this runs
after kfree(hwc->caller_ctx), a concurrent mana_hwc_rx_event_handler()
can dereference freed caller_ctx (and rxq->msg_buf) in
mana_hwc_handle_resp().
Fix this by reordering teardown to reverse-of-creation order: destroy
the TX/RX work queues and CQ/EQ before freeing hwc->caller_ctx. This
ensures all in-flight interrupt handlers complete before the memory they
access is freed.
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Dipayaan Roy <dipayanroy@linux.microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/abHA3AjNtqa1nx9k@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62ea8b77ed ]
Currently when the HWC creation fails, the error handling is flawed,
e.g. if mana_hwc_create_channel() -> mana_hwc_establish_channel() fails,
the resources acquired in mana_hwc_init_queues() is not released.
Enhance mana_hwc_destroy_channel() to do the proper cleanup work and
call it accordingly.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fa103fc8f5 ("net: mana: fix use-after-free in mana_hwc_destroy_channel() by reordering teardown")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cfc3bc02b ]
Some systems require more than 5ms to get into WoL mode. Increase the
timeout value to 50ms.
Fixes: c51de7f397 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260312191852.3904571-1-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8dbdc6e38 ]
There is an AB-BA deadlock when both LEDS_TRIGGER_NETDEV and
LED_TRIGGER_PHY are enabled:
[ 1362.049207] [<8054e4b8>] led_trigger_register+0x5c/0x1fc <-- Trying to get lock "triggers_list_lock" via down_write(&triggers_list_lock);
[ 1362.054536] [<80662830>] phy_led_triggers_register+0xd0/0x234
[ 1362.060329] [<8065e200>] phy_attach_direct+0x33c/0x40c
[ 1362.065489] [<80651fc4>] phylink_fwnode_phy_connect+0x15c/0x23c
[ 1362.071480] [<8066ee18>] mtk_open+0x7c/0xba0
[ 1362.075849] [<806d714c>] __dev_open+0x280/0x2b0
[ 1362.080384] [<806d7668>] __dev_change_flags+0x244/0x24c
[ 1362.085598] [<806d7698>] dev_change_flags+0x28/0x78
[ 1362.090528] [<807150e4>] dev_ioctl+0x4c0/0x654 <-- Hold lock "rtnl_mutex" by calling rtnl_lock();
[ 1362.094985] [<80694360>] sock_ioctl+0x2f4/0x4e0
[ 1362.099567] [<802e9c4c>] sys_ioctl+0x32c/0xd8c
[ 1362.104022] [<80014504>] syscall_common+0x34/0x58
Here LED_TRIGGER_PHY is registering LED triggers during phy_attach
while holding RTNL and then taking triggers_list_lock.
[ 1362.191101] [<806c2640>] register_netdevice_notifier+0x60/0x168 <-- Trying to get lock "rtnl_mutex" via rtnl_lock();
[ 1362.197073] [<805504ac>] netdev_trig_activate+0x194/0x1e4
[ 1362.202490] [<8054e28c>] led_trigger_set+0x1d4/0x360 <-- Hold lock "triggers_list_lock" by down_read(&triggers_list_lock);
[ 1362.207511] [<8054eb38>] led_trigger_write+0xd8/0x14c
[ 1362.212566] [<80381d98>] sysfs_kf_bin_write+0x80/0xbc
[ 1362.217688] [<8037fcd8>] kernfs_fop_write_iter+0x17c/0x28c
[ 1362.223174] [<802cbd70>] vfs_write+0x21c/0x3c4
[ 1362.227712] [<802cc0c4>] ksys_write+0x78/0x12c
[ 1362.232164] [<80014504>] syscall_common+0x34/0x58
Here LEDS_TRIGGER_NETDEV is being enabled on an LED. It first takes
triggers_list_lock and then RTNL. A classical AB-BA deadlock.
phy_led_triggers_registers() does not require the RTNL, it does not
make any calls into the network stack which require protection. There
is also no requirement the PHY has been attached to a MAC, the
triggers only make use of phydev state. This allows the call to
phy_led_triggers_registers() to be placed elsewhere. PHY probe() and
release() don't hold RTNL, so solving the AB-BA deadlock.
Reported-by: Shiji Yang <yangshiji66@outlook.com>
Closes: https://lore.kernel.org/all/OS7PR01MB13602B128BA1AD3FA38B6D1FFBC69A@OS7PR01MB13602.jpnprd01.prod.outlook.com/
Fixes: 06f502f57d ("leds: trigger: Introduce a NETDEV trigger")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://patch.msgid.link/20260222152601.1978655-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
[ dropped `is_on_sfp_module` guards and `CONFIG_PHYLIB_LEDS`/`of_phy_leds` logic ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03cc8f90d0 ]
The lbs_free_adapter() function uses timer_delete() (non-synchronous)
for both command_timer and tx_lockup_timer before the structure is
freed. This is incorrect because timer_delete() does not wait for
any running timer callback to complete.
If a timer callback is executing when lbs_free_adapter() is called,
the callback will access freed memory since lbs_cfg_free() frees the
containing structure immediately after lbs_free_adapter() returns.
Both timer callbacks (lbs_cmd_timeout_handler and lbs_tx_lockup_handler)
access priv->driver_lock, priv->cur_cmd, priv->dev, and other fields,
which would all be use-after-free violations.
Use timer_delete_sync() instead to ensure any running timer callback
has completed before returning.
This bug was introduced in commit 8f641d93c3 ("libertas: detect TX
lockups and reset hardware") where del_timer() was used instead of
del_timer_sync() in the cleanup path. The command_timer has had the
same issue since the driver was first written.
Fixes: 8f641d93c3 ("libertas: detect TX lockups and reset hardware")
Fixes: 954ee164f4 ("[PATCH] libertas: reorganize and simplify init sequence")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Hodges <git@danielhodges.dev>
Link: https://patch.msgid.link/20260206195356.15647-1-git@danielhodges.dev
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[ del_timer() => timer_delete_sync() ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1aa5ef892 upstream.
Current clk_csr_i setting of Loongson STMMAC (including LS7A1000/2000
and LS2K1000/2000/3000) are copy & paste from other drivers. In fact,
Loongson STMMAC use 125MHz clocks and need 62 freq division to within
2.5MHz, meeting most PHY MDC requirement. So fix by setting clk_csr_i
to 100-150MHz, otherwise some PHYs may link fail.
Cc: stable@vger.kernel.org
Fixes: 30bba69d7d ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/20260203062901.2158236-1-chenhuacai@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2503d08f8a upstream.
Normal RX/TX interrupts are enabled later, in arc_emac_open(), so probe
should not see interrupt delivery in the usual case. However, hardware may
still present stale or latched interrupt status left by firmware or the
bootloader.
If probe later unwinds after devm_request_irq() has installed the handler,
such a stale interrupt can still reach arc_emac_intr() during teardown and
race with release of the associated net_device.
Avoid that window by putting the device into a known quiescent state before
requesting the IRQ: disable all EMAC interrupt sources and clear any
pending EMAC interrupt status bits. This keeps the change hardware-focused
and minimal, while preventing spurious IRQ delivery from leftover state.
Fixes: e4f2379db6 ("ethernet/arc/arc_emac - Add new driver")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Link: https://patch.msgid.link/20260309132409.584966-1-fanwu01@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb4903b335 upstream.
Executing ethtool -m can fail reporting a netlink I/O error while firmware
link management holds the i2c bus used to communicate with the module.
According to Intel(R) Ethernet Controller E810 Datasheet Rev 2.8 [1]
Section 3.3.10.4 Read/Write SFF EEPROM (0x06EE)
request should to be retried upon receiving EBUSY from firmware.
Commit e9c9692c8a ("ice: Reimplement module reads used by ethtool")
implemented it only for part of ice_get_module_eeprom(), leaving all other
calls to ice_aq_sff_eeprom() vulnerable to returning early on getting
EBUSY without retrying.
Remove the retry loop from ice_get_module_eeprom() and add Admin Queue
(AQ) command with opcode 0x06EE to the list of commands that should be
retried on receiving EBUSY from firmware.
Cc: stable@vger.kernel.org
Fixes: e9c9692c8a ("ice: Reimplement module reads used by ethtool")
Signed-off-by: Jakub Staniszewski <jakub.staniszewski@linux.intel.com>
Co-developed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Signed-off-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://www.intel.com/content/www/us/en/content-details/613875/intel-ethernet-controller-e810-datasheet.html [1]
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dabffd0854 upstream.
MANA hardware requires at least one doorbell ring every 8 wraparounds
of the CQ. The driver rings the doorbell as a form of flow control to
inform hardware that CQEs have been consumed.
The NAPI poll functions mana_poll_tx_cq() and mana_poll_rx_cq() can
poll up to CQE_POLLING_BUFFER (512) completions per call. If the CQ
has fewer than 512 entries, a single poll call can process more than
4 wraparounds without ringing the doorbell. The doorbell threshold
check also uses ">" instead of ">=", delaying the ring by one extra
CQE beyond 4 wraparounds. Combined, these issues can cause the driver
to exceed the 8-wraparound hardware limit, leading to missed
completions and stalled queues.
Fix this by capping the number of CQEs polled per call to 4 wraparounds
of the CQ in both TX and RX paths. Also change the doorbell threshold
from ">" to ">=" so the doorbell is rung as soon as 4 wraparounds are
reached.
Cc: stable@vger.kernel.org
Fixes: 58a63729c9 ("net: mana: Fix doorbell out of order violation and avoid unnecessary doorbell rings")
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260226192833.1050807-1-longli@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9cc0e440f upstream.
Do not configure Latency Tolerance Messaging (LTM) on USB 2.0 hardware.
The LAN7850 is a High-Speed (USB 2.0) only device and does not support
SuperSpeed features like LTM. Currently, the driver unconditionally
attempts to configure LTM registers during initialization. On the
LAN7850, these registers do not exist, resulting in writes to invalid
or undocumented memory space.
This issue was identified during a port to the regmap API with strict
register validation enabled. While no functional issues or crashes have
been observed from these invalid writes, bypassing LTM initialization
on the LAN7850 ensures the driver strictly adheres to the hardware's
valid register map.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260305143429.530909-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4f774a0cc upstream.
Do not drop packets with checksum errors at the USB driver level;
pass them to the network stack.
Previously, the driver dropped all packets where the 'Receive Error
Detected' (RED) bit was set, regardless of the specific error type. This
caused packets with only IP or TCP/UDP checksum errors to be dropped
before reaching the kernel, preventing the network stack from accounting
for them or performing software fallback.
Add a mask for hard hardware errors to safely drop genuinely corrupt
frames, while allowing checksum-errored frames to pass with their
ip_summed field explicitly set to CHECKSUM_NONE.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260305143429.530909-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dc26ca99b8 ]
The NIX RAS health reporter recovery routine checks nix_af_rvu_int to
decide whether to re-enable NIX_AF_RAS interrupts. This is the RVU
interrupt status field and is unrelated to RAS events, so the recovery
flow may incorrectly skip re-enabling NIX_AF_RAS interrupts.
Check nix_af_rvu_ras instead before writing NIX_AF_RAS_ENA_W1S.
Fixes: 5ed66306ea ("octeontx2-af: Add devlink health reporters for NIX")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Link: https://patch.msgid.link/20260310184824.1183651-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e94eaef111 ]
If an error is encountered while mapping TX buffers, the driver should
unmap any buffers already mapped for that skb.
Because count is incremented after a successful mapping, it will always
match the correct number of unmappings needed when dma_error is reached.
Decrementing count before the while loop in dma_error causes an
off-by-one error. If any mapping was successful before an unsuccessful
mapping, exactly one DMA mapping would leak.
In these commits, a faulty while condition caused an infinite loop in
dma_error:
Commit 03b1320dfc ("e1000e: remove use of skb_dma_map from e1000e
driver")
Commit 602c0554d7 ("e1000: remove use of skb_dma_map from e1000 driver")
Commit c1fa347f20 ("e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of
unsigned in *_tx_map()") fixed the infinite loop, but introduced the
off-by-one error.
This issue may still exist in the igbvf driver, but I did not address it
in this patch.
Fixes: c1fa347f20 ("e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of unsigned in *_tx_map()")
Assisted-by: Claude:claude-4.6-opus
Signed-off-by: Matt Vollrath <tactii@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e809085f49 ]
Fix following issues in the IPv4 and IPv6 cloud filter handling logic in
both the add and delete paths:
- The source-IP mask check incorrectly compares mask.src_ip[0] against
tcf.dst_ip[0]. Update it to compare against tcf.src_ip[0]. This likely
goes unnoticed because the check is in an "else if" path that only
executes when dst_ip is not set, most cloud filter use cases focus on
destination-IP matching, and the buggy condition can accidentally
evaluate true in some cases.
- memcpy() for the IPv4 source address incorrectly uses
ARRAY_SIZE(tcf.dst_ip) instead of ARRAY_SIZE(tcf.src_ip), although
both arrays are the same size.
- The IPv4 memcpy operations used ARRAY_SIZE(tcf.dst_ip) and ARRAY_SIZE
(tcf.src_ip), Update these to use sizeof(cfilter->ip.v4.dst_ip) and
sizeof(cfilter->ip.v4.src_ip) to ensure correct and explicit copy size.
- In the IPv6 delete path, memcmp() uses sizeof(src_ip6) when comparing
dst_ip6 fields. Replace this with sizeof(dst_ip6) to make the intent
explicit, even though both fields are struct in6_addr.
Fixes: e284fc2804 ("i40e: Add and delete cloud filter")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47bba09b14 ]
In hi3110_open(), the return value of hi3110_power_enable() is not checked.
If power enable fails, the device may not function correctly, while the
driver still returns success.
Add a check for the return value and propagate the error accordingly.
Signed-off-by: Wenyuan Li <2063309626@qq.com>
Link: https://patch.msgid.link/tencent_B5E2E7528BB28AA8A2A56E16C49BD58B8B07@qq.com
Fixes: 57e83fb9b7 ("can: hi311x: Add Holt HI-311x CAN driver")
[mkl: adjust subject, commit message and jump label]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3348be7978 ]
Before the fixed commit, we check slave->new_link during commit
state, which values are only BOND_LINK_{NOCHANGE, UP, DOWN}. After
the commit, we start using slave->link_new_state, which state also could
be BOND_LINK_{FAIL, BACK}.
For example, when we set updelay/downdelay, after a failover,
the slave->link_new_state could be set to BOND_LINK_{FAIL, BACK} in
bond_miimon_inspect(). And later in bond_miimon_commit(), it will treat
it as invalid and print an error, which would cause confusion for users.
[ 106.440254] bond0: (slave veth2): link status down for interface, disabling it in 200 ms
[ 106.440265] bond0: (slave veth2): invalid new link 1 on slave
[ 106.648276] bond0: (slave veth2): link status definitely down, disabling slave
[ 107.480271] bond0: (slave veth2): link status up, enabling it in 200 ms
[ 107.480288] bond0: (slave veth2): invalid new link 3 on slave
[ 107.688302] bond0: (slave veth2): link status definitely up, 10000 Mbps full duplex
Let's handle BOND_LINK_{FAIL, BACK} as valid link states.
Fixes: 1899bb3251 ("bonding: fix state transition issue in link monitoring")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20260304-b4-bond_updelay-v1-2-f72eb2e454d0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 168ff39e47 ]
When booting with the 'ipv6.disable=1' parameter, the nd_tbl is never
initialized because inet6_init() exits before ndisc_init() is called
which initializes it. If an IPv6 packet is injected into the interface,
route_shortcircuit() is called and a NULL pointer dereference happens on
neigh_lookup().
BUG: kernel NULL pointer dereference, address: 0000000000000380
Oops: Oops: 0000 [#1] SMP NOPTI
[...]
RIP: 0010:neigh_lookup+0x20/0x270
[...]
Call Trace:
<TASK>
vxlan_xmit+0x638/0x1ef0 [vxlan]
dev_hard_start_xmit+0x9e/0x2e0
__dev_queue_xmit+0xbee/0x14e0
packet_sendmsg+0x116f/0x1930
__sys_sendto+0x1f5/0x200
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x12f/0x1590
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fix this by adding an early check on route_shortcircuit() when protocol
is ETH_P_IPV6. Note that ipv6_mod_enabled() cannot be used here because
VXLAN can be built-in even when IPv6 is built as a module.
Fixes: e15a00aafa ("vxlan: add ipv6 route short circuit support")
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Link: https://patch.msgid.link/20260304120357.9778-2-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
