[ Upstream commit b809d04099 ]
In mana_hwc_rx_event_handler(), rx_req_idx is derived from
sge->address in DMA-coherent memory. In Confidential VMs
(SEV-SNP/TDX), this memory is shared unencrypted and HW can modify
WQE contents at any time. No bounds check exists on rx_req_idx,
which can lead to an out-of-bounds access into reqs[].
Add bounds check on rx_req_idx in mana_hwc_rx_event_handler() before
using it to index the reqs[] array.
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Aditya Garg <gargaditya@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://patch.msgid.link/20260520051553.857120-1-gargaditya@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35f0f0a253 ]
In mana_hwc_rx_event_handler(), resp->response.hwc_msg_id is read from
DMA-coherent memory and bounds-checked, then mana_hwc_handle_resp()
re-reads the same field from the same DMA buffer for test_bit() and
pointer arithmetic.
DMA-coherent memory is mapped uncacheable on x86 and is shared,
unencrypted, in Confidential VMs (SEV-SNP/TDX), so each load goes
directly to host-visible memory. A H/W can modify the value
between the check and the use, bypassing the bounds validation.
Fix this by reading hwc_msg_id exactly once using READ_ONCE() into a
stack-local variable in mana_hwc_rx_event_handler(), and passing the
validated value as a parameter to mana_hwc_handle_resp().
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Link: https://patch.msgid.link/20260514194156.466823-1-ernis@linux.microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ac85bcfd4 ]
The BPC, RGAC1 and RGAC2 registers control the handling of link-local
frames with reserved MAC DAs (01:80:C2:00:00:0x). These frames are
correctly trapped to the CPU port, but the egress VLAN tag attribute was
set to MT7530_VLAN_EG_UNTAGGED which causes the switch to strip any
VLAN tags from trapped frames before they reach the CPU.
This causes VLAN-tagged link-local frames (STP BPDUs, LLDP, PTP Peer
Delay Requests) to arrive at the CPU without their VLAN tag, so they
are delivered to the base network interface instead of the VLAN
sub-interface. The DSA local_termination selftest confirms this: all
link-local protocol tests on VLAN upper interfaces fail.
Set the EG_TAG attribute to MT7530_VLAN_EG_DISABLED (system default)
so that the switch does not modify VLAN tags in trapped frames. This
way VLAN-tagged frames retain their original tag and are delivered to
the correct VLAN sub-interface, matching the behavior of non-trapped
frames which pass through without VLAN tag modification.
Fixes: 69ddba9d17 ("net: dsa: mt7530: fix handling of all link-local frames")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/891e0cd34db2a5fe20ceb73283a81fb5f71427ca.1778766629.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7603a0c7d2 ]
The mt753x_bpdu_port_fw enum is globally used for manipulating the process
of deciding the forwardable ports, specifically concerning the CPU port(s).
Therefore, rename it and the values in it to mt753x_to_cpu_fw.
Change FOLLOW_MFC to SYSTEM_DEFAULT to be on par with the switch documents.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 3ac85bcfd4 ("net: dsa: mt7530: preserve VLAN tags on trapped link-local frames")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e824e40d0e ]
The DSA forwarding selftests bridge_vlan_aware.sh and
bridge_vlan_unaware.sh configure the bridge with ageing_time set to
LOW_AGEING_TIME (1000 centiseconds, i.e. 10 seconds) and then run
learning_test() in lib.sh, which expects a learned FDB entry to be
removed after ageing_time + 10 seconds. On MT7530/MT7531 the entry
persisted past the deadline and the "Found FDB record when should
not" assertion failed.
With msecs=10000, the algorithm in mt7530_set_ageing_time() finds
AGE_CNT=0 and AGE_UNIT=9 as the first exact match (starting the
search from tmp_age_count=0). The per-entry aging counter is
initialized to AGE_CNT when a MAC address is learned, so with
AGE_CNT=0 new entries start with a counter value of 0, which the
hardware treats as "already aged" and never removes, effectively
disabling aging.
Fix this by starting the search from tmp_age_count=1 to ensure
entries always have a non-zero initial aging counter. For a
10-second ageing time this yields AGE_CNT=1 and AGE_UNIT=4 instead:
the timer ticks every 5 seconds and entries are removed after 2
ticks.
Starting the search at AGE_CNT=1 raises the minimum representable
ageing time from 1 to 2 seconds. Without bounds, a stale ageing_time
of 1 second would now make the loop fall through without setting
age_count and age_unit, leaving them uninitialized when written to
the MT7530_AAC hardware register. Set ds->ageing_time_min and
ds->ageing_time_max so the DSA core validates the range before the
callback is invoked, and drop the now-redundant range check from
mt7530_set_ageing_time().
Fixes: ea6d5c924e ("net: dsa: mt7530: support setting ageing time")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/7788ded12dc07b1bce329ec35fa70f4b45f3f9b7.1778766629.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 497041d763 ]
MT7531 standalone and MMIO variants found in MT7988 and EN7581 share
most basic properties. Despite that, assisted_learning_on_cpu_port and
mtu_enforcement_ingress were only applied for MT7531 but not for MT7988
or EN7581, causing the expected issues on MMIO devices.
Apply both settings equally also for MT7988 and EN7581 by moving both
assignments form mt7531_setup() to mt7531_setup_common().
This fixes unwanted flooding of packets due to unknown unicast
during DA lookup, as well as issues with heterogenous MTU settings.
Fixes: 7f54cc9772 ("net: dsa: mt7530: split-off common parts from mt7531_setup")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/89ed7ec6d4fa0395ac53ad2809742bb1ce61ed12.1745290867.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: e824e40d0e ("net: dsa: mt7530: fix FDB entries not aging out with short timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55dda532bb ]
Fix two instances where we used to directly return the result of
ath11k_wmi_cmd_send(...). Because we did not check the return value, we
also did not free the skb in the error path.
Fixes: 79802b13a4 ("ath11k: implement WoW enable and wakeup commands")
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260506134240.2284016-2-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36a8d04a82 ]
The legacy ARM board file for MACH_MX31ADS was removed in commit
c93197b004 ("ARM: imx: Remove i.MX31 board files"), but a reference
to it remained in the cs89x0 driver. Drop this unused code.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Fixes: c93197b004 ("ARM: imx: Remove i.MX31 board files")
Link: https://patch.msgid.link/20260509023732.42256-1-enelsonmoore@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebd8ec2b30 ]
The gmac_rx() NAPI poll function assembles packets in an
SKB from a ring buffer.
If the ring buffer gets completely emptied during a poll cycle,
we exit gmac_rx(), but the packet is not yet completely
assembled in the SKB, yet the fragment counter frag_nr is
reset to zero on the next invocation.
Solve this by making the RX fragment counter a part of the
port struct, and carry it over between invocations.
Reset the fragment counter only right after calling
napi_gro_frags(), on error (after calling napi_free_frags())
or if stopping the port.
Reset it in some place where not strictly necessary just to
emphasize what is going on.
This was found by Sashiko during normal patch review.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Link: https://sashiko.dev/#/patchset/20260505-gemini-ethernet-fix-v2-1-997c31d06079%40kernel.org
Signed-off-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260509-gemini-ethernet-fixes-v1-3-6c5d20ddc35b@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b266bacba7 ]
In gmac_rx() (drivers/net/ethernet/cortina/gemini.c), when
gmac_get_queue_page() returns NULL for the second page of a multi-page
fragment, the driver logs an error and continues — but does not free the
partially assembled skb that was being assembled via napi_build_skb() /
napi_get_frags().
Free the in-progress partially assembled skb via napi_free_frags()
and increase the number of dropped frames appropriately
and assign the skb pointer NULL to make sure it is not lingering
around, matching the pattern already used elsewhere in the driver.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Andreas Haarmann-Thiemann <eitschman@nebelreich.de>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/20260505-gemini-ethernet-fix-v2-1-997c31d06079@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06937db21e ]
The SKB used to assemble packets from fragments in gmac_rx()
is static local, but the Gemini has two ethernet ports, meaning
there can be races between the ports on a bad day if a device
is using both.
Make the RX SKB a per-port variable and carry it over between
invocations in the port struct instead.
Zero the pointer once we call napi_gro_frags(), on error (after
calling napi_free_frags()) or if the port is stopped.
Zero it in some place where not strictly necessary just to
emphasize what is going on.
This was found by Sashiko during normal patch review.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Link: https://sashiko.dev/#/patchset/20260505-gemini-ethernet-fix-v2-1-997c31d06079%40kernel.org
Signed-off-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260509-gemini-ethernet-fixes-v1-2-6c5d20ddc35b@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ded1f36ba ]
Move the mutex_lock() call up to prevent that DCB settings change after
the first ice_query_port_ets() call. The second ice_query_port_ets()
call in ice_dcb_rebuild() is already protected by pf->tc_mutex.
This also fixes a bug in an error path, as before taking the first
"goto dcb_error" in the function jumped over mutex_lock() to
mutex_unlock().
This bug has been detected by the clang thread-safety analyzer.
Cc: intel-wired-lan@lists.osuosl.org
Fixes: 242b5e068b ("ice: Fix DCB rebuild after reset")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260506-jk-iwl-net-2026-05-04-v2-6-a5ea4dc837a9@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5d49b568c1 upstream.
ixgbevf_clean_rx_irq() prunes frames whose source MAC matches the VF's
own address (VEPA multicast workaround) by freeing the skb and
continuing to the next descriptor:
dev_kfree_skb_irq(skb);
continue;
The skb pointer is declared outside the while loop and persists across
iterations. Because the continue skips the "skb = NULL" reset at the
bottom of the loop, the next iteration enters the "else if (skb)" path
and calls ixgbevf_add_rx_frag() on the freed skb, dereferencing
skb_shinfo(skb)->nr_frags - a use-after-free in NAPI softirq context.
The sibling driver iavf already handles this correctly by nulling the
pointer before continuing. Apply the same pattern here.
I do not have ixgbevf hardware; the bug was found by static analysis
(scan_drop_continue_loops.py + semgrep drop_continue_in_loop, multi-tool
corroboration with the highest score in the scan). The UAF was confirmed
under KASAN by loading a test module that reproduces the exact code
pattern (alloc skb, kfree_skb, then read skb_shinfo(skb)->nr_frags):
BUG: KASAN: slab-use-after-free in ixgbevf_uaf_test_init+0x100/0x1000
Read of size 8 at addr 000000006163ae78 by task insmod/30
freed 208-byte region [000000006163adc0, 000000006163ae90)
QEMU emulates igb (82576) but not ixgbe (82599), and the igbvf VF
driver does not include the VEPA source pruning path, so a full
end-to-end reproduction with emulated hardware was not possible.
Fixes: bad17234ba ("ixgbevf: Change receive model to use double buffered page based receives")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260515182419.1597859-8-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f51e4b3b55 upstream.
LMAC rings reuse the shared rdp/wrp pointer buffers without going
through the normal SRNG hw-init path that zeros non-LMAC ring
pointers. After restart, ath11k_hal_srng_clear() can therefore hand
stale hp/tp state from the previous firmware instance back to the new
one.
Clear the shared pointer buffers while keeping the allocations in
place so restart still avoids reallocating SRNG DMA memory, but starts
with fresh ring-pointer state.
Fixes: 32be3ca4cf ("wifi: ath11k: HAL SRNG: don't deinitialize and re-initialize again")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/all/CAOPSVF04q6uvVdq8GTRLHBrVMdpt9=o9wVcFMc6f-yhmSBcZqQ@mail.gmail.com/
Signed-off-by: Kyle Farnung <kfarnung@gmail.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260513-kfarnung-ath11k-srng-clear-pointer-state-v1-1-bc700dd8b333@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a1730245e upstream.
Setting RBUF_EEE_EN | RBUF_PM_EN in RBUF_ENERGY_CTRL breaks the RX
path on GENET hardware once MAC EEE becomes active. RX traffic stops
flowing while the link stays up and the usual descriptor/RX error
counters remain quiet. In that state the MAC still accepts frames
(rbuf_ovflow_cnt keeps climbing) but RBUF no longer forwards them to
DMA, so rx_packets is no longer incremented at the netdev level. On
some boards the corruption ends up as a paging fault in
skb_release_data via bcmgenet_rx_poll on an LPI exit.
Reproduced on Pi 4B (BCM2711 + BCM54213PE) and confirmed by Florian
Fainelli on an internal Broadcom 4908-family board with the same crash
signature. RBUF_PM_EN is not publicly documented.
This shows up more often now that phy_support_eee() enables EEE by
default, but it also affects older kernels as soon as TX LPI is
turned on via ethtool, so it is not specific to recent changes.
Always clear RBUF_EEE_EN | RBUF_PM_EN in bcmgenet_eee_enable_set so
the bits stay off across resets. UMAC and TBUF setup is left alone so
TX-side EEE keeps working.
Link: https://github.com/raspberrypi/linux/issues/7304
Fixes: 6ef398ea60 ("net: bcmgenet: add EEE support")
Cc: stable@vger.kernel.org
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260520184320.652053-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5d93b2c40 upstream.
The memory allocated in ipc_protocol_init() is not freed on the error
paths that follow in ipc_imem_init(). Fix that by calling the
corresponding release function ipc_protocol_deinit() in the error path.
Fixes: 3670970dd8 ("net: iosm: shared memory IPC interface")
Cc: stable@vger.kernel.org
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Link: https://patch.msgid.link/20260519062815.55545-1-nihaal@cse.iitm.ac.in
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f2b28b79d ]
There are actually 2 problems:
- deleting the last element doesn't require the memmove of elements
[i + 1, end) over it. Actually, element i+1 is out of bounds.
- The memmove itself should move size - i - 1 elements, because the last
element is out of bounds.
The out-of-bounds element still remains out of bounds after being
accessed, so the problem is only that we touch it, not that it becomes
in active use. But I suppose it can lead to issues if the out-of-bounds
element is part of an unmapped page.
Fixes: 6666cebc5e ("net: dsa: sja1105: Add support for VLAN operations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318115716.2124395-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Rajani Kantha <681739313@139.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2c308cf342 upstream.
The shutdown handler aq_pci_shutdown() unconditionally calls
pci_wake_from_d3(pdev, false), clearing the PCI PME_En bit even when
wake-on-LAN has been configured. While aq_nic_shutdown() correctly
programs the NIC firmware via aq_nic_set_power() to listen for magic
packets, the PCI subsystem will not propagate the resulting PME wake
event from D3, so the system never wakes after poweroff.
WOL from suspend (S3) is unaffected because aq_suspend_common() does
not touch pci_wake_from_d3() and relies on the PM core's wake
configuration via device_may_wakeup().
This affects all atlantic-supported NICs (AQC107/108/111/112/113);
users have reported that WOL works if the atlantic driver is never
loaded, but breaks once it has run its shutdown path.
Pass the configured WOL state to pci_wake_from_d3() instead of a
literal false, so the PCI PME_En bit is preserved when the user has
armed WOL via ethtool.
Fixes: 90869ddfef ("net: aquantia: Implement pci shutdown callback")
Cc: stable@vger.kernel.org
Signed-off-by: Zoran Ilievski <goodboy@rexbytes.com>
Reviewed-by: Sukhdeep Singh <sukhdeeps@marvell.com>
Link: https://patch.msgid.link/20260511064002.1857-1-goodboy@rexbytes.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 678b713ece upstream.
PTP pin structs are allocated early in probe, but never cleaned up.
Fix this by calling i40e_ptp_free_pins in the error path.
To support this, i40e_ptp_free_pins is added to the header and
pin_config is correctly nullified after being freed.
This has been an issue since i40e_ptp_alloc_pins was introduced.
Fixes: 1050713026 ("i40e: add support for PTP external synchronization clock")
Reported-by: Kohei Enju <kohei@enjuk.jp>
Cc: stable@vger.kernel.org
Signed-off-by: Matt Vollrath <tactii@gmail.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Kohei Enju <kohei@enjuk.jp>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260506-jk-iwl-net-2026-05-04-v2-2-a5ea4dc837a9@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aa6c6d9ee0 ]
bareudp_fill_metadata_dst() passes bareudp->sock to
udp_tunnel6_dst_lookup() in the IPv6 path without a NULL check.
The socket is only created in bareudp_open() and NULLed in
bareudp_stop(), so calling this function while the device is down
triggers a NULL dereference via sock->sk.
BUG: kernel NULL pointer dereference, address: 0000000000000018
RIP: 0010:udp_tunnel6_dst_lookup (net/ipv6/ip6_udp_tunnel.c:160)
Call Trace:
<TASK>
bareudp_fill_metadata_dst (drivers/net/bareudp.c:532)
do_execute_actions (net/openvswitch/actions.c:901)
ovs_execute_actions (net/openvswitch/actions.c:1589)
ovs_packet_cmd_execute (net/openvswitch/datapath.c:700)
genl_family_rcv_msg_doit (net/netlink/genetlink.c:1114)
genl_rcv_msg (net/netlink/genetlink.c:1209)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
</TASK>
Add a NULL check returning -ESHUTDOWN, consistent with the xmit paths
in the same driver.
Fixes: 571912c69f ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260426165350.1663137-2-bestswngs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc47e86dbf ]
At the moment ip6_dst_lookup_tunnel() is used only by bareudp.
Ideally, other UDP tunnel implementations should use it, but to do so
the function needs to accept new parameters that are specific for UDP
tunnels, such as the ports.
Prepare for these changes by renaming the function to
udp_tunnel6_dst_lookup() and move it to file
net/ipv6/ip6_udp_tunnel.c.
This is similar to what already done for IPv4 in commit bf3fcbf7e7
("ipv4: rename and move ip_route_output_tunnel()").
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aa6c6d9ee0 ("bareudp: fix NULL pointer dereference in bareudp_fill_metadata_dst()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72fc68c635 ]
We want to make the function more generic so that it can be used by
other UDP tunnel implementations such as geneve and vxlan. To do that,
add the following arguments:
- source and destination UDP port;
- ifindex of the output interface, needed by vxlan;
- the tos, because in some cases it is not taken from struct
ip_tunnel_info (for example, when it's inherited from the inner
packet);
- the dst cache, because not all tunnel types (e.g. vxlan) want to
use the one from struct ip_tunnel_info.
With these parameters, the function no longer needs the full struct
ip_tunnel_info as argument and we can pass only the relevant part of
it (struct ip_tunnel_key).
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aa6c6d9ee0 ("bareudp: fix NULL pointer dereference in bareudp_fill_metadata_dst()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78f3655adc ]
The function is now UDP-specific, the protocol is always IPPROTO_UDP.
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aa6c6d9ee0 ("bareudp: fix NULL pointer dereference in bareudp_fill_metadata_dst()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf3fcbf7e7 ]
At the moment ip_route_output_tunnel() is used only by bareudp.
Ideally, other UDP tunnel implementations should use it, but to do so
the function needs to accept new parameters that are specific for UDP
tunnels, such as the ports.
Prepare for these changes by renaming the function to
udp_tunnel_dst_lookup() and move it to file
net/ipv4/udp_tunnel_core.c.
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aa6c6d9ee0 ("bareudp: fix NULL pointer dereference in bareudp_fill_metadata_dst()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46f74a3f7d ]
Table 7-121 in datasheet says we have to set register 0xc6
to value 0x10 before CLK_O_SEL can be modified. No more infos
about this field found in datasheet. With this fix, setting
of CLK_O_SEL field in IO_MUX_CFG register worked through dts
property "ti,clk-output-sel" on a DP83869HMRGZR.
Signed-off-by: Heiko Schocher <hs@nabladev.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 01db923e83 ("net: phy: dp83869: Add TI dp83869 phy")
Link: https://patch.msgid.link/20260425031339.3318-1-hs@nabladev.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adbe2cdf75 ]
When rtl8150_start_xmit() fails to submit the tx URB, the URB is never
handed to the USB core and write_bulk_callback() will not run. The
driver returns NETDEV_TX_OK, which tells the networking stack that the
skb has been consumed, but nothing actually frees the skb on this
error path:
dev->tx_skb = skb;
...
if ((res = usb_submit_urb(dev->tx_urb, GFP_ATOMIC))) {
...
/* no kfree_skb here */
}
return NETDEV_TX_OK;
This leaks the skb on every submit failure and also leaves dev->tx_skb
pointing at memory that the driver itself may later free, which is
fragile.
Free the skb with dev_kfree_skb_any() in the error path and clear
dev->tx_skb so no stale pointer is left behind.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Morduan Zang <zhangdandan@uniontech.com>
Link: https://patch.msgid.link/E7D3E1C013C5A859+20260424015517.9574-1-zhangdandan@uniontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23f0e34c64 ]
syzbot reported a KASAN slab-use-after-free read in rtl8150_start_xmit()
when accessing skb->len for tx statistics after usb_submit_urb() has
been called:
BUG: KASAN: slab-use-after-free in rtl8150_start_xmit+0x71f/0x760
drivers/net/usb/rtl8150.c:712
Read of size 4 at addr ffff88810eb7a930 by task kworker/0:4/5226
The URB completion handler write_bulk_callback() frees the skb via
dev_kfree_skb_irq(dev->tx_skb). The URB may complete on another CPU
in softirq context before usb_submit_urb() returns in the submitter,
so by the time the submitter reads skb->len the skb has already been
queued to the per-CPU completion_queue and freed by net_tx_action():
CPU A (xmit) CPU B (USB completion softirq)
------------ ------------------------------
dev->tx_skb = skb;
usb_submit_urb() --+
|-------> write_bulk_callback()
| dev_kfree_skb_irq(dev->tx_skb)
| net_tx_action()
| napi_skb_cache_put() <-- free
netdev->stats.tx_bytes |
+= skb->len; <-- UAF read
Fix it by caching skb->len before submitting the URB and using the
cached value when updating the tx_bytes counter.
The pre-existing tx_bytes semantics are preserved: the counter tracks
the original frame length (skb->len), not the ETH_ZLEN/USB-alignment
padded "count" value that is handed to the device. Changing that
would be a user-visible accounting change and is out of scope for
this UAF fix.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: syzbot+3f46c095ac0ca048cb71@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/69e69ee7.050a0220.24bfd3.002b.GAE@google.com/
Closes: https://syzkaller.appspot.com/bug?extid=3f46c095ac0ca048cb71
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Zhan Jun <zhanjun@uniontech.com>
Link: https://patch.msgid.link/809895186B866C10+20260423004913.136655-1-zhangdandan@uniontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2674d603a9 ]
RCU readers that identified a net device as a VRF port using
netif_is_l3_slave() assume that a subsequent call to
netdev_master_upper_dev_get_rcu() will return a VRF device. They then
continue to dereference its l3mdev operations.
This assumption is not always correct and can result in a NPD [1]. There
is no RCU synchronization when removing a port from a VRF, so it is
possible for an RCU reader to see a new master device (e.g., a bridge)
that does not have l3mdev operations.
Fix by adding RCU synchronization after clearing the IFF_L3MDEV_SLAVE
flag. Skip this synchronization when a net device is removed from a VRF
as part of its deletion and when the VRF device itself is deleted. In
the latter case an RCU grace period will pass by the time RTNL is
released.
[1]
BUG: kernel NULL pointer dereference, address: 0000000000000000
[...]
RIP: 0010:l3mdev_fib_table_rcu (net/l3mdev/l3mdev.c:181)
[...]
Call Trace:
<TASK>
l3mdev_fib_table_by_index (net/l3mdev/l3mdev.c:201 net/l3mdev/l3mdev.c:189)
__inet_bind (net/ipv4/af_inet.c:499 (discriminator 3))
inet_bind_sk (net/ipv4/af_inet.c:469)
__sys_bind (./include/linux/file.h:62 (discriminator 1) ./include/linux/file.h:83 (discriminator 1) net/socket.c:1951 (discriminator 1))
__x64_sys_bind (net/socket.c:1969 (discriminator 1) net/socket.c:1967 (discriminator 1) net/socket.c:1967 (discriminator 1))
do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1))
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Fixes: fdeea7be88 ("net: vrf: Set slave's private flag before linking")
Reported-by: Haoze Xie <royenheart@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Yuan Tan <yuantan098@gmail.com>
Closes: https://lore.kernel.org/netdev/20260419145332.3988923-1-n05ec@lzu.edu.cn/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20260423063607.1208202-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35eaa6d8d6 ]
Syzbot reports a KMSAN uninit-value originating from
nsim_dev_trap_skb_build, with the allocation also
being performed in the same function.
Fix this by calling skb_put_zero instead of skb_put to
guarantee zero initialization of the whole IP header.
Closes: https://syzkaller.appspot.com/bug?extid=23d7fcd204e3837866ff
Fixes: da58f90f11 ("netdevsim: Add devlink-trap support")
Signed-off-by: Nikola Z. Ivanov <zlatistiv@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260426201434.742030-1-zlatistiv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4078c5611d ]
There is a mismatch between the passed arguments and the actual
nfp_encode_basic_qdr() function parameter names:
static int nfp_encode_basic_qdr(u64 addr, int dest_island, int cpp_tgt,
int mode, bool addr40, int isld1,
int isld0)
{
...
But "dest_island" and "cpp_tgt" are swapped at every call-site.
For example:
return nfp_encode_basic_qdr(*addr, cpp_tgt, dest_island,
mode, addr40, isld1, isld0);
As a result, nfp_encode_basic_qdr() receives "dest_island" as CPP target
type, which is always NFP_CPP_TARGET_QDR(2) for these calls, and "cpp_tgt"
as the destination island ID, which can accidentally match or be outside
the valid NFP_CPP_TARGET_* types (e.g. '-1' for any destination).
Since code already worked for years, also add extra pr_warn() to error
paths in nfp_encode_basic_qdr() to help identify any potential address
verification failures.
Detected using the static analysis tool - Svace.
Fixes: 4cb584e0ee ("nfp: add CPP access core")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Link: https://patch.msgid.link/20260422160536.61855-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c1367a2d7 ]
slhc_uncompress() parses a VJ-compressed TCP header by advancing a
pointer through the packet via decode() and pull16(). Neither helper
bounds-checks against isize, and decode() masks its return with
& 0xffff so it can never return the -1 that callers test for -- those
error paths are dead code.
A short compressed frame whose change byte requests optional fields
lets decode() read past the end of the packet. The over-read bytes
are folded into the cached cstate and reflected into subsequent
reconstructed packets.
Make decode() and pull16() take the packet end pointer and return -1
when exhausted. Add a bounds check before the TCP-checksum read.
The existing == -1 tests now do what they were always meant to.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20260414134126.758795-2-horms@kernel.org/
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260416100147.531855-5-bestswngs@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e76607442d ]
slhc_init() accepts rslots == 0 as a valid configuration, with the
documented meaning of 'no receive compression'. In that case the
allocation loop in slhc_init() is skipped, so comp->rstate stays
NULL and comp->rslot_limit stays 0 (from the kzalloc of struct
slcompress).
The receive helpers do not defend against that configuration.
slhc_uncompress() dereferences comp->rstate[x] when the VJ header
carries an explicit connection ID, and slhc_remember() later assigns
cs = &comp->rstate[...] after only comparing the packet's slot number
to comp->rslot_limit. Because rslot_limit is 0, slot 0 passes the
range check, and the code dereferences a NULL rstate.
The configuration is reachable in-tree through PPP. PPPIOCSMAXCID
stores its argument in a signed int, and (val >> 16) uses arithmetic
shift. Passing 0xffff0000 therefore sign-extends to -1, so val2 + 1
is 0 and ppp_generic.c ends up calling slhc_init(0, 1). Because
/dev/ppp open is gated by ns_capable(CAP_NET_ADMIN), the whole path
is reachable from an unprivileged user namespace. Once the malformed
VJ state is installed, any inbound VJ-compressed or VJ-uncompressed
frame that selects slot 0 crashes the kernel in softirq context:
Oops: general protection fault, probably for non-canonical
address 0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:slhc_uncompress (drivers/net/slip/slhc.c:519)
Call Trace:
<TASK>
ppp_receive_nonmp_frame (drivers/net/ppp/ppp_generic.c:2466)
ppp_input (drivers/net/ppp/ppp_generic.c:2359)
ppp_async_process (drivers/net/ppp/ppp_async.c:492)
tasklet_action_common (kernel/softirq.c:926)
handle_softirqs (kernel/softirq.c:623)
run_ksoftirqd (kernel/softirq.c:1055)
smpboot_thread_fn (kernel/smpboot.c:160)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:164)
</TASK>
Reject the receive side on such instances instead of touching rstate.
slhc_uncompress() falls through to its existing 'bad' label, which
bumps sls_i_error and enters the toss state. slhc_remember() mirrors
that with an explicit sls_i_error increment followed by slhc_toss();
the sls_i_runt counter is not used here because a missing rstate is
an internal configuration state, not a runt packet.
The transmit path is unaffected: the only in-tree caller that picks
rslots from userspace (ppp_generic.c) still supplies tslots >= 1, and
slip.c always calls slhc_init(16, 16), so comp->tstate remains valid
and slhc_compress() continues to work.
Fixes: 4ab42d78e3 ("ppp, slip: Validate VJ compression slot parameters completely")
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260415204130.258866-2-bestswngs@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc1ff87bce ]
RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT
RECOMMENDED for PPPoE. In practice, pppd does not support negotiating
PFC for PPPoE sessions, and the current PPPoE driver assumes an
uncompressed (2-byte) protocol field. However, the generic PPP layer
function ppp_input() is not aware of the negotiation result, and still
accepts PFC frames.
If a peer with a broken implementation or an attacker sends a frame with
a compressed (1-byte) protocol field, the subsequent PPP payload is
shifted by one byte. This causes the network header to be 4-byte
misaligned, which may trigger unaligned access exceptions on some
architectures.
To reduce the attack surface, drop PPPoE PFC frames. Introduce
ppp_skb_is_compressed_proto() helper function to be used in both
ppp_generic.c and pppoe.c to avoid open-coding.
Fixes: 7fb1b8ca8f ("ppp: Move PFC decompression to PPP generic layer")
Signed-off-by: Qingfang Deng <qingfang.deng@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260415022456.141758-2-qingfang.deng@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa3f7fe409 ]
If probe fails after registering the PTP clock and its delayed work,
these resources must be released.
This was not an issue until a 2016 fix moved the e1000e_ptp_init() call
before the jump to err_register.
Fixes: aa524b66c5 ("e1000e: don't modify SYSTIM registers during SIOCSHWTSTAMP ioctl")
Signed-off-by: Matt Vollrath <tactii@gmail.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260416-iwl-net-submission-2026-04-14-v2-12-686c33c9828d@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a24162f188 ]
i40e advertises IFF_SUPP_NOFCS, allowing users to use the SO_NOFCS
socket option. However, this option is silently ignored, as the driver
does not check skb->no_fcs, and always enables FCS insertion offload.
Fix this by removing the advertisement of IFF_SUPP_NOFCS.
This behavior can be reproduced with a simple AF_PACKET socket:
import socket
s = socket.socket(socket.AF_PACKET, socket.SOCK_RAW)
s.setsockopt(socket.SOL_SOCKET, 43, 1) # SO_NOFCS
s.bind(("eth0", 0))
s.send(b'\xff' * 64)
Previously, send() succeeds but the driver ignores SO_NOFCS.
With this change, send() fails with -EPROTONOSUPPORT, as expected.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Kohei Enju <kohei@enjuk.jp>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260416-iwl-net-submission-2026-04-14-v2-9-686c33c9828d@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7a62edd34 ]
As noted in the blamed commit, the AR8035 and other PHYs from this
family advertise the Extended Next Page support by default, which may be
understood by some partners as this PHY being multi-gig capable.
The fix is to disable XNP advertising, which is done by setting bit 12
of the Auto-Negotiation Advertisement Register (MII_ADVERTISE).
The blamed commit incorrectly uses MDIO_AN_CTRL1_XNP, which is bit 13 as per
802.3 : 45.2.7.1 AN control register (Register 7.0)
BIT 12 in MII_ADVERTISE is wrapped by ADVERTISE_RESV, used by some
drivers such as the aquantia one. 802.3 Clause 28 defines bit 12 as
Extended Next Page ability, at least in recent versions of the standard.
Let's add a define for it and use it in the at803x driver.
Fixes: 3c51fa5d2a ("net: phy: ar803x: disable extended next page bit")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260410171021.1277138-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bb6379416 ]
/dev/ppp open is currently authorized against file->f_cred->user_ns,
while unattached administrative ioctls operate on current->nsproxy->net_ns.
As a result, a local unprivileged user can create a new user namespace
with CLONE_NEWUSER, gain CAP_NET_ADMIN only in that new user namespace,
and still issue PPPIOCNEWUNIT, PPPIOCATTACH, or PPPIOCATTCHAN against
an inherited network namespace.
Require CAP_NET_ADMIN in the user namespace that owns the target network
namespace before handling unattached PPP administrative ioctls.
This preserves normal pppd operation in the network namespace it is
actually privileged in, while rejecting the userns-only inherited-netns
case.
Fixes: 273ec51dd7 ("net: ppp_generic - introduce net-namespace functionality v2")
Signed-off-by: Taegu Ha <hataegu0826@gmail.com>
Link: https://patch.msgid.link/20260409071117.4354-1-hataegu0826@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf9a38803b ]
sixpack_receive_buf() does not properly skip bytes with TTY error flags.
The while loop iterates through the flags buffer but never advances the
data pointer (cp), and passes the original count (including error bytes)
to sixpack_decode(). This causes sixpack_decode() to process bytes that
should have been skipped due to TTY errors. The TTY layer does not
guarantee that cp[i] holds a meaningful value when fp[i] is set, so
passing those positions to sixpack_decode() results in KMSAN reporting
an uninit-value read.
Fix this by processing bytes one at a time, advancing cp on each
iteration, and only passing valid (non-error) bytes to sixpack_decode().
This matches the pattern used by slip_receive_buf() and
mkiss_receive_buf() for the same purpose.
Reported-by: syzbot+ecdb8c9878a81eb21e54@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ecdb8c9878a81eb21e54
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Mashiro Chen <mashiro.chen@mailbox.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260407173101.107352-1-mashiro.chen@mailbox.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1241b384ef ]
In tty, u8 is now used for data, ssize_t for sizes (with possible
negative error codes). Propagate these types to 6pack.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-hams@vger.kernel.org
Cc: netdev@vger.kernel.org
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240808103549.429349-12-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: bf9a38803b ("net: hamradio: 6pack: fix uninit-value in sixpack_receive_buf")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57f3f53d2c ]
The write_ptr points to the next open tx_cb. We want to return the
tx_cb that gets rewinded, so we must rewind the pointer first then
return the tx_cb that it points to. That way the txcb can be correctly
cleaned up.
Fixes: 876dbadd53 ("net: bcmgenet: Fix unmapping of fragments in bcmgenet_xmit()")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260406175756.134567-2-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ef5789d99 ]
port->bc_queue_len_used is read and written locklessly,
add READ_ONCE()/WRITE_ONCE() annotations.
While WRITE_ONCE() in macvlan_fill_info() is not yet needed,
it is a prereq for future RTNL avoidance.
Fixes: d4bff72c84 ("macvlan: Support for high multicast packet rate")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260401103809.3038139-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48afd5124f ]
The old code used ocp_write_byte() to clear the OOBS_POLLING bit
(BIT(8)) in the USB_UPHY_XTAL register, but this doesn't correctly
clear a bit in the upper byte of the 16-bit register.
Fix this by using ocp_write_word() instead.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Chih Kai Hsu <hsu.chih.kai@realtek.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20260326073925.32976-454-nic_swsd@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97daf00745 ]
CONFIG_FSL_DPAA2_ETH and CONFIG_FSL_DPAA2_SWITCH are not
associated, but the compilation of FSL_DPAA2_SWITCH depends on
the compilation of the dpaa2 folder. The files controlled by
CONFIG_FSL_DPAA2_SWITCH in the dpaa2 folder are not controlled
by CONFIG_FSL_DPAA2_ETH, except for the files controlled by
CONFIG_FSL_DPAA2_SWITCH. Therefore, removing the restriction will
not affect the compilation of the files in the directory.
Fixes: f48298d3fb ("staging: dpaa2-switch: move the driver out of staging")
Suggested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Cai Xinchen <caixinchen1@huawei.com>
Link: https://patch.msgid.link/20260312065907.476663-3-caixinchen1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12589892f4 ]
Since the commit 84cba72956 ("dpaa2-switch: integrate
the MAC endpoint support") included dpaa2-mac.o in the driver,
but it didn't select PCS_LYNX, PHYLINK and FSL_XGMAC_MDIO. it
will lead to link error, such as
undefined reference to `phylink_ethtool_ksettings_set'
undefined reference to `lynx_pcs_create_fwnode'
And the same reason as the commit d2624e70a2 ("dpaa2-eth: select
XGMAC_MDIO for MDIO bus support"), enable the FSL_XGMAC_MDIO Kconfig
option in order to have MDIO access to internal and external PHYs.
Because dpaa2-switch uses fsl_mc_driver APIs, add depends on FSL_MC_BUS
&& FSL_MC_DPIO as FSL_DPAA2_SWITCH do.
FSL_XGMAC_MDIO and FSL_MC_BUS depend on OF, thus the dependence of
FSL_MC_BUS can satisfy FSL_XGMAC_MDIO's OF requirement.
Fixes: 84cba72956 ("dpaa2-switch: integrate the MAC endpoint support")
Suggested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Cai Xinchen <caixinchen1@huawei.com>
Link: https://patch.msgid.link/20260312065907.476663-2-caixinchen1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 039cd522dc ]
The irq_prepare_bcn_tasklet is initialized in rtl_pci_init() and
scheduled when RTL_IMR_BCNINT interrupt is triggered by hardware.
But it is never killed in rtl_pci_deinit(). When the rtlwifi card
probe fails or is being detached, the ieee80211_hw is deallocated.
However, irq_prepare_bcn_tasklet may still be running or pending,
leading to use-after-free when the freed ieee80211_hw is accessed
in _rtl_pci_prepare_bcn_tasklet().
Similar to irq_tasklet, add tasklet_kill() in rtl_pci_deinit() to
ensure that irq_prepare_bcn_tasklet is properly terminated before
the ieee80211_hw is released.
The issue was identified through static analysis.
Fixes: 0c8173385e ("rtl8192ce: Add new driver")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260223045522.48377-1-duoming@zju.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 990a73dec3 ]
In mwifiex_11n_aggregate_pkt(), skb_aggr is allocated via
mwifiex_alloc_dma_align_buf(). If mwifiex_is_ralist_valid() returns false,
the function currently returns -1 immediately without freeing the
previously allocated skb_aggr, causing a memory leak.
Since skb_aggr has not yet been queued via skb_queue_tail(), no other
references to this memory exist. Therefore, it has to be freed locally
before returning the error.
Fix this by calling mwifiex_write_data_complete() to free skb_aggr before
returning the error status.
Compile tested only. Issue found using a prototype static analysis tool
and code review.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Jeff Chen <jeff.chen_1@nxp.com>
Link: https://patch.msgid.link/20260119092625.1349934-1-zilin@seu.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cc427d24ac upstream.
Some physical adapters on Power systems do not support segmentation
offload when the MSS is less than 224 bytes. Attempting to send such
packets causes the adapter to freeze, stopping all traffic until
manually reset.
Implement ndo_features_check to disable GSO for packets with small MSS
values. The network stack will perform software segmentation instead.
The 224-byte minimum matches ibmvnic
commit <f10b09ef68> ("ibmvnic: Enforce stronger sanity checks
on GSO packets")
which uses the same physical adapters in SEA configurations.
The issue occurs specifically when the hardware attempts to perform
segmentation (gso_segs > 1) with a small MSS. Single-segment GSO packets
(gso_segs == 1) do not trigger the problematic LSO code path and are
transmitted normally without segmentation.
Add an ndo_features_check callback to disable GSO when MSS < 224 bytes.
Also call vlan_features_check() to ensure proper handling of VLAN packets,
particularly QinQ (802.1ad) configurations where the hardware parser may
not support certain offload features.
Validated using iptables to force small MSS values. Without the fix,
the adapter freezes. With the fix, packets are segmented in software
and transmission succeeds. Comprehensive regression testing completedd
(MSS tests, performance, stability).
Fixes: 8641dd8579 ("ibmveth: Add support for TSO")
Cc: stable@vger.kernel.org
Reviewed-by: Brian King <bjking1@linux.ibm.com>
Tested-by: Shaik Abdulla <shaik.abdulla1@ibm.com>
Tested-by: Naveed Ahmed <naveedaus@in.ibm.com>
Signed-off-by: Mingming Cao <mmc@linux.ibm.com>
Link: https://patch.msgid.link/20260424162917.65725-1-mmc@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f4f78bf85 upstream.
The firmware-controlled key index in b43_rx() can exceed the dev->key[]
array size (58 entries). The existing B43_WARN_ON is non-enforcing in
production builds, allowing an out-of-bounds read.
Make the B43_WARN_ON check enforcing by dropping the frame when the
firmware returns an invalid key index.
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Fixes: e4d6b79518 ("[B43]: add mac80211-based driver for modern BCM43xx devices")
Cc: stable@vger.kernel.org
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Link: https://patch.msgid.link/20260417111145.2694196-1-tristmd@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
