[ Upstream commit 62443dc211 ]
`ip6t_eui64`, `xt_mac`, the `bitmap:ip,mac`, `hash:ip,mac`, and
`hash:mac` ipset types, and `nf_log_syslog` access `eth_hdr(skb)`
after either assuming that the skb is associated with an Ethernet
device or checking only that the `ETH_HLEN` bytes at
`skb_mac_header(skb)` lie between `skb->head` and `skb->data`.
Make these paths first verify that the skb is associated with an
Ethernet device, that the MAC header was set, and that it spans at
least a full Ethernet header before accessing `eth_hdr(skb)`.
Suggested-by: Florian Westphal <fw@strlen.de>
Tested-by: Ren Wei <enjou1224z@gmail.com>
Signed-off-by: Zhengchuan Liang <zcliangcn@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ff24f2ecfd upstream.
Session lookups in tp_list matched only on destination address (and
optionally session ID), leaving role validation to the caller. If two
sessions with the same other_end coexisted (one as sender, one as receiver)
a lookup could silently return the wrong one, causing the caller's role to
bail out early, potentially skipping necessary cleanup.
Move the role check into the lookup functions themselves so the correct
entry is always returned, or none at all. Since batadv_tp_start()
legitimately needs to detect any active session to a destination regardless
of role, introduce a dedicated helper for that case rather than bending the
existing lookup semantics.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71dce47f07 upstream.
batadv_tp_sender_shutdown() previously used two separate variables to track
session state: sending (an atomic flag indicating whether the session was
active) and reason (a plain enum storing the stop reason). This introduced
a race window between the two writes: after sending was cleared to 0,
batadv_tp_send() could observe the stopped state and call
batadv_tp_sender_end() before reason was written, causing the wrong stop
reason to be reported to the caller.
Fix this by consolidating both variables into a single atomic send_result,
which holds 0 while the session is running and the stop reason once it
ends.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 149324fc76 upstream.
bluetoothd has a bug with makes it send extra bytes as part of
MGMT_OP_ADD_EXT_ADV_DATA which are now being checked to be the
exact the expected length, relax this so only when the expected
length is greater than the data length to cause an error since
that would result in accessing invalid memory, otherwise just
ignore the extra bytes.
Link: https://lore.kernel.org/linux-bluetooth/20260602204749.210857-1-luiz.dentz@gmail.com/T/#u
Fixes: d3f7d17960 ("Bluetooth: MGMT: validate Add Extended Advertising Data length")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77098e4bea upstream.
The receiver shutdown timer handler, batadv_tp_receiver_shutdown(), is
responsible for releasing the tp_vars reference it holds. However, the
existing logic for coordinating this release with batadv_tp_stop_all() was
flawed.
timer_shutdown_sync() guarantees the timer will not fire again after it
returns, but it returns non-zero only when the timer was pending at the
time of the call. If the timer had already expired (and
batadv_tp_stop_all() would unsucessfully try to rearm itself),
batadv_tp_stop_all() skips its batadv_tp_vars_put(), and
batadv_tp_receiver_shutdown() fails to put its own reference as well.
Fix this by introducing a new atomic variable receiving that is set to 1
when the receiver is initialized and cleared atomically with atomic_xchg()
by whichever side claims it first. Only the side that observes the
transition from 1 to 0 is responsible for releasing the tp_vars timer
reference, eliminating the uncertainty.
Cc: stable@kernel.org
Fixes: 3d3cf6a731 ("batman-adv: stop tp_meter sessions during mesh teardown")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ab24fdebc ]
The MPTCP output path access locklessly the MPTCP-level ack_seq
in multiple times, using possibly different values for the data_ack
in the DSS option and to compute the announced rcv wnd for the same
packet.
Refactor the cote to avoid inconsistencies which may confuse the
peer. Also ensure that the MPTCP level rcv wnd is updated only when
the egress packet actually contains a DSS ack.
Fixes: fa3fe2b150 ("mptcp: track window announced to peer")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260602-net-mptcp-misc-fixes-7-1-rc7-v2-3-856831229976@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e67ba9bb5 ]
ioam6_fill_trace_data() stores the schema contribution to the trace
length in a u8. With bit 22 enabled and the largest schema payload,
sclen becomes 1 + 1020 / 4, wraps from 256 to 0, and bypasses the
remaining-space check. __ioam6_fill_trace_data() then positions the
write cursor without reserving the schema area but still copies the
4-byte schema header and the full schema payload, overrunning the trace
buffer.
Keep sclen in an unsigned int so the remaining-space check and the write
cursor calculation both see the full schema length.
Fixes: 8c6f6fa677 ("ipv6: ioam: IOAM Generic Netlink API")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: Justin Iurman <justin.iurman@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Li hongliang <1468888505@139.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce425dd05d upstream.
When batadv_tp_start() or batadv_tp_init_recv() fail to allocate a new
tp_vars object, the previously incremented bat_priv->tp_num counter is
never decremented. This causes tp_num to drift upward on each allocation
failure. Since only BATADV_TP_MAX_NUM sessions can be started and the count
is never reduced for these failed allocations, it causes to an exhaustion
of throughput meter sessions. In worst case, no new throughput meter
session can be started until the mesh interface is removed.
The error handling must decrement tp_num releasing the lock and aborting
the creation of an throughput meter session
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[ Context ]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d3cf6a731 upstream.
TP meter sessions remain linked on bat_priv->tp_list after the netlink
request has already finished. When the mesh interface is removed,
batadv_mesh_free() currently tears down the mesh without first draining
these sessions.
A running sender thread or a late incoming tp_meter packet can then keep
processing against a mesh instance which is already shutting down.
Synchronize tp_meter with the mesh lifetime by stopping all active
sessions from batadv_mesh_free() and waiting for sender threads to exit
before teardown continues.
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Co-developed-by: Luxing Yin <tr0jan@lzu.edu.cn>
Signed-off-by: Luxing Yin <tr0jan@lzu.edu.cn>
Signed-off-by: Jiexun Wang <wangjiexun2025@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[ Context ]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05cfe9863e upstream.
Protocol checksum validation fails for IPv6 if there are extension
headers before the protocol header. iph->len already contains its
offset, so use it to fix the problem.
Fixes: 2906f66a56 ("ipvs: SCTP Trasport Loadbalancing Support")
Fixes: 0bbdd42b7e ("IPVS: Extend protocol DNAT/SNAT and state handlers")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Nazar Kalashnikov <nazarkalashnikov0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab185e0c4f ]
For NFT_FIB_RESULT_OIFNAME the destination register is declared with
len = IFNAMSIZ (four 32-bit registers), but on the lookup-fail,
RTN_LOCAL and oif-mismatch paths nft_fib{4,6}_eval() only writes one
register via "*dest = 0". The remaining three registers are left as
whatever was on the stack in nft_do_chain()'s struct nft_regs, and a
downstream expression that loads the register span can leak that
uninitialised kernel stack to userspace.
The NFTA_FIB_F_PRESENT existence check has the same shape: it is only
meaningful for NFT_FIB_RESULT_OIF, yet it was accepted for any result type
while the eval stores a single byte via nft_reg_store8(), leaving the rest
of the declared span stale.
Fix both:
- replace the bare "*dest = 0" in the eval with nft_fib_store_result(),
which strscpy_pad()s the whole IFNAMSIZ for OIFNAME (and is already
used on the other early-return path), and
- restrict NFTA_FIB_F_PRESENT to NFT_FIB_RESULT_OIF and declare its
destination as a single u8, so the marked span matches the one byte
the eval writes.
Fixes: f6d0cbcf09 ("netfilter: nf_tables: add fib expression")
Suggested-by: Florian Westphal <fw@strlen.de>
Cc: stable@vger.kernel.org
Signed-off-by: Davide Ornaghi <d.ornaghi97@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[ kept the tree's existing `ip6_route_lookup`/`rt6_info` machinery (missing `fib6_lookup` refactor) and changed only `*dest = 0;` to `nft_fib_store_result(dest, priv, NULL)` ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 98d0912e9f ]
pskb_carve_inside_header() and pskb_carve_inside_nonlinear() both copy
the old skb_shared_info header into a new buffer via memcpy(), which
includes the destructor_arg pointer (uarg) for MSG_ZEROCOPY skbs.
Neither function calls net_zcopy_get() for the new shinfo, creating an
unaccounted holder: every skb_shared_info with destructor_arg set will
call skb_zcopy_clear() once when freed, but the corresponding
net_zcopy_get() was never called for the new copy. Repeated calls
drive uarg->refcnt to zero prematurely, freeing ubuf_info_msgzc while
TX skbs still hold live destructor_arg pointers.
KASAN reports use-after-free on a freed ubuf_info_msgzc:
BUG: KASAN: slab-use-after-free in skb_release_data+0x77b/0x810
Read of size 8 at addr ffff88801574d3e8 by task poc/220
Call Trace:
skb_release_data+0x77b/0x810
kfree_skb_list_reason+0x13e/0x610
skb_release_data+0x4cd/0x810
sk_skb_reason_drop+0xf3/0x340
skb_queue_purge_reason+0x282/0x440
rds_tcp_inc_free+0x1e/0x30
rds_recvmsg+0x354/0x1780
__sys_recvmsg+0xdf/0x180
Allocated by task 219:
msg_zerocopy_realloc+0x157/0x7b0
tcp_sendmsg_locked+0x2892/0x3ba0
Freed by task 219:
ip_recv_error+0x74a/0xb10
tcp_recvmsg+0x475/0x530
The skb consuming the late access still referenced the same uarg via
shinfo->destructor_arg copied by pskb_carve_inside_nonlinear() without
a refcount bump. This has been verified to be reliably exploitable: a
working proof-of-concept achieves full root privilege escalation from
an unprivileged local user on a default kernel configuration.
The fix follows the pattern of pskb_expand_head() which has the same
memcpy/cloned structure. For pskb_carve_inside_header(), net_zcopy_get()
is placed after skb_orphan_frags() succeeds, so the orphan error path
needs no cleanup. For pskb_carve_inside_nonlinear(), net_zcopy_get() is
placed after all failure points and just before skb_release_data(), so
no error path needs cleanup at all -- matching pskb_expand_head() more
closely and avoiding the need for a balancing net_zcopy_put().
Fixes: 6fa01ccd88 ("skbuff: Add pskb_extract() helper function")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-sonnet-4-6
Signed-off-by: Minh Nguyen <minhnguyen.080505@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260526041240.329462-1-minhnguyen.080505@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c8e620467 ]
l2cap_chan_close() removes the channel from conn->chan_l, which
must be done under conn->lock. cleanup_listen() runs under the
parent sk_lock, so acquiring conn->lock would invert the
established conn->lock -> chan->lock -> sk_lock order.
Instead of calling l2cap_chan_close() directly, schedule
l2cap_chan_timeout with delay 0 to close the channel
asynchronously. The timeout handler already acquires conn->lock
and chan->lock in the correct order.
The timer is only armed when chan->conn is still set: if it is
already NULL, l2cap_conn_del() has already processed this channel
(l2cap_chan_del + l2cap_sock_teardown_cb + l2cap_sock_close_cb),
so there is nothing left to do. If l2cap_conn_del() races in
after the timer is armed, __clear_chan_timer() inside
l2cap_chan_del() cancels it; if the timer has already fired, the
handler returns harmlessly because chan->conn was cleared.
Fixes: 3df91ea20e ("Bluetooth: Revert to mutexes from RCU list")
Cc: <stable@vger.kernel.org> # 0b58004: Bluetooth: fix UAF in l2cap_sock_cleanup_listen() vs l2cap_conn_del()
Signed-off-by: Siwei Zhang <oss@fourdim.xyz>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 50c2d91c5d ]
When a packet arrives with map_seq < ack_seq < end_seq, the beginning
of the packet has already been acknowledged but the end contains new
data. Currently the entire packet is dropped as "old data," forcing
the sender to retransmit.
Instead, skip the already-acked bytes by adjusting the skb offset and
enqueue only the new portion. Update bytes_received and ack_seq to
reflect the new data consumed.
A previous attempt at this fix has been sent by Paolo Abeni [1], but had
issues [2]: it also added a zero-window check and changed rcv_wnd_sent
initialization, which caused test regressions. This version addresses
only the partial packet handling without modifying receive window
accounting.
Fixes: ab174ad8ef ("mptcp: move ooo skbs into msk out of order queue.")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/c9b426a4e163aa3c4fe8b80c79f1a610f47ae7d8.1763075056.git.pabeni@redhat.com [1]
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/600 [2]
Signed-off-by: Shardul Bankar <shardul.b@mpiricsoftware.com>
[pabeni@redhat.com: update map]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260515-net-mptcp-misc-fixes-7-1-rc4-v2-1-701e96419f2f@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
[ dropped `msk->bytes_received += copy_len;` and relocated the `drop:` label to the function end for the existing RCVPRUNED `goto drop;` ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 51e398a3b8 ]
When TCP option space is insufficient (e.g., when sending ADD_ADDR with an
IPv6 address and port while tcp_timestamps is enabled), the original code
jumped to out_unlock without clearing the addr_signal flag. This caused
mptcp_pm_add_timer to keep rescheduling indefinitely, not sending ADD_ADDR,
preventing subsequent addresses in the endpoint list from being announced.
Handle this case by clearing the ADD_ADDR signal and skipping the matching
ADD_ADDR retransmission entry. The skip path cancels the matching timer
(with id check) and advances PM state progression, preserving forward
progress to subsequent PM work.
This cancellation is inherently best-effort. A concurrent add_timer
callback may already be running and may acquire pm.lock before the
cancel path updates entry state. In that case, one final ADD_ADDR
transmit attempt can still be executed.
Once the cancel path sets entry->retrans_times to ADD_ADDR_RETRANS_MAX,
the callback-side retrans_times check suppresses further ADD_ADDR
retransmissions.
Note that when an ADD_ADDR is being prepared, a pure-ACK is queued. On
the output side, it means that it is fine to skip non-pure-ACK packets,
when drop_other_suboptions is set: a pure-ACK will be processed soon
after.
Fixes: 00cfd77b90 ("mptcp: retransmit ADD_ADDR when timeout")
Cc: stable@vger.kernel.org
Signed-off-by: Li Xiasong <lixiasong1@huawei.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260515-net-mptcp-misc-fixes-7-1-rc4-v2-2-701e96419f2f@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de4eda9de2 ]
READ/WRITE proved to be actively confusing - the meanings are
"data destination, as used with read(2)" and "data source, as
used with write(2)", but people keep interpreting those as
"we read data from it" and "we write data to it", i.e. exactly
the wrong way.
Call them ITER_DEST and ITER_SOURCE - at least that is harder
to misinterpret...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Stable-dep-of: a4f0b00178 ("vsock/virtio: reset connection on receiving queue overflow")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d4ea0dfd75 ]
Reported by Sashiko:
The function ipv6_hop_ioam() accesses
__in6_dev_get(skb->dev)->cnf.ioam6_enabled without validating the returned
idev pointer. Because addrconf_ifdown() can concurrently clear dev->ip6_ptr
via RCU, __in6_dev_get() can return NULL during interface teardown, which
could cause a NULL pointer dereference when processing an IOAM Hop-by-Hop
option.
Let's add a check and use SKB_DROP_REASON_IPV6DISABLED accordingly.
Fixes: 9ee11f0fff ("ipv6: ioam: Data plane support for Pre-allocated Trace")
Cc: stable@vger.kernel.org
Signed-off-by: Justin Iurman <justin.iurman@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260517183059.29140-1-justin.iurman@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aaec7096f9 ]
HSR node-list and node-status generic-netlink operations run under
rcu_read_lock(). They walk hsr->node_db through hsr_get_next_node() and
hsr_get_node_data(), but RTM_DELLINK teardown removes the same node table
with plain list_del() and frees each node immediately.
That lets a generic-netlink reader hold a struct hsr_node pointer across
hsr_dellink(). In a KASAN build, widening the reader window after
hsr_get_next_node() obtains the node reproduces a slab-use-after-free
when the reader copies node->macaddress_A; the freeing stack is
hsr_del_nodes() from hsr_dellink().
Use list_del_rcu() and defer the free through the existing
hsr_free_node_rcu() callback. This matches the lifetime rule used by the
HSR prune paths, which already delete nodes with list_del_rcu() and
call_rcu().
Fixes: b9a1e62740 ("hsr: implement dellink to clean up resources")
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Link: https://patch.msgid.link/20260513233838.3064715-2-michael.bommarito@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ replaced `list_del`+`call_rcu(hsr_free_node_rcu)` with `list_del_rcu`+`kfree_rcu(node, rcu_head)` ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e83f5e24da ]
bt_sock_poll() walks the accept queue without synchronization, while
child teardown can unlink the same socket and drop its last reference.
The unsynchronized accept queue walk has existed since the initial
Bluetooth import.
Protect accept_q with a dedicated lock for queue updates and polling.
Also rework bt_accept_dequeue() to take temporary child references under
the queue lock before dropping it and locking the child socket.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reported-by: Jann Horn <jannh@google.com>
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Signed-off-by: Jiexun Wang <wangjiexun2025@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Jiexun Wang <wangjiexun2025@gmail.com>
Reviewed-by: Jann Horn <jannh@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 464c702fb9 ]
This makes sure peer information is always available via sock when using
bt_sock_alloc.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: e83f5e24da ("Bluetooth: serialize accept_q access")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6bfa273e53 ]
This consolidates code around sk_alloc into bt_sock_alloc which does
take care of common initialization.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: e83f5e24da ("Bluetooth: serialize accept_q access")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3f7d17960 ]
MGMT_OP_ADD_EXT_ADV_DATA is registered as a variable-length command,
with MGMT_ADD_EXT_ADV_DATA_SIZE as the fixed header size. The handler
then uses cp->adv_data_len and cp->scan_rsp_len to validate and copy
cp->data, but it never checks that those bytes are part of the mgmt
command payload.
A short command can therefore make add_ext_adv_data() pass an
out-of-bounds pointer into tlv_data_is_valid(). If the bytes beyond
the command buffer are addressable, they can also be copied into the
advertising instance as scan response data, where the caller can read
them back via MGMT_OP_GET_ADV_INSTANCE. The trigger requires
CAP_NET_ADMIN in the initial user namespace; KASAN reports an 8-byte
slab-out-of-bounds read.
Reject commands whose length does not match the fixed header plus both
advertising data lengths before parsing cp->data.
Fixes: 1241057283 ("Bluetooth: Break add adv into two mgmt commands")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab1513597c ]
bt_accept_dequeue() unlinks a not-yet-accepted child from the parent
accept queue and release_sock()s it before returning, so the returned
sk has no caller reference and is unlocked.
l2cap_sock_cleanup_listen() walks these children on listening-socket
close. A concurrent HCI disconnect drives hci_rx_work ->
l2cap_conn_del() which runs l2cap_chan_del() + l2cap_sock_kill() and
frees the child sk and its l2cap_chan; cleanup_listen() then uses both:
BUG: KASAN: slab-use-after-free in l2cap_sock_kill
l2cap_sock_kill / l2cap_sock_cleanup_listen / __x64_sys_close
Freed by: l2cap_conn_del -> l2cap_sock_close_cb -> l2cap_sock_kill
This is distinct from the two fixes already in this area: commit
e83f5e24da ("Bluetooth: serialize accept_q access") serialises the
accept_q list/poll and takes temporary refs inside bt_accept_dequeue(),
and CVE-2025-39860 serialises the userspace close()/accept() race by
calling cleanup_listen() under lock_sock() in l2cap_sock_release().
Neither covers l2cap_conn_del() running from hci_rx_work, so this UAF
still reproduces on current bluetooth/master.
Take the reference at the source: bt_accept_dequeue() does sock_hold()
while sk is still locked, before release_sock(); callers sock_put().
cleanup_listen() pins the chan with l2cap_chan_hold_unless_zero() under
a brief child sk lock (serialising vs l2cap_sock_teardown_cb()), drops
it before l2cap_chan_lock(), and skips a duplicate l2cap_sock_kill() on
SOCK_DEAD. conn->lock is not taken here: cleanup_listen() runs under
the parent sk lock and that would invert
conn->lock -> chan->lock -> sk_lock (lockdep).
KASAN/SMP: an unprivileged listen/close vs HCI-disconnect race produced
12 use-after-free reports per run before this change; 0, and no lockdep
report, over 1600+ raced iterations after it on bluetooth/master.
Fixes: 15f02b9105 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode")
Cc: stable@vger.kernel.org
Reported-by: Siwei Zhang <oss@fourdim.xyz>
Reviewed-by: Siwei Zhang <oss@fourdim.xyz>
Signed-off-by: Safa Karakuş <safa.karakus@secunnix.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd4d7263d5 ]
As explained in commit e03781879a ("drop_monitor: Require
'CAP_SYS_ADMIN' when joining "events" group"), the "flags" field in the
multicast group structure reuses uAPI flags despite the field not being
exposed to user space. This makes it impossible to extend its use
without adding new uAPI flags, which is inappropriate for internal
kernel checks.
Solve this by adding internal flags (i.e., "GENL_MCAST_*") and convert
the existing users to use them instead of the uAPI flags.
Tested using the reproducers in commit 44ec98ea5e ("psample: Require
'CAP_NET_ADMIN' when joining "packets" group") and commit e03781879a
("drop_monitor: Require 'CAP_SYS_ADMIN' when joining "events" group").
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d1ebfce2c1 ("smb: client: require net admin for CIFS SWN netlink")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3cf1249289 ]
When an ADD_ADDR needs to be retransmitted and another one has already
been prepared -- e.g. multiple ADD_ADDRs have been sent in a row and
need to be retransmitted later -- this additional retransmission will
need to wait.
In this case, the timer was reset to TCP_RTO_MAX / 8, which is ~15
seconds. This delay is unnecessary long: it should just be rescheduled
at the next opportunity, e.g. after the retransmission timeout.
Without this modification, some issues can be seen from time to time in
the selftests when multiple ADD_ADDRs are sent, and the host takes time
to process them, e.g. the "signal addresses, ADD_ADDR timeout" MPTCP
Join selftest, especially with a debug kernel config.
Note that on older kernels, 'timeout' is not available. It should be
enough to replace it by one second (HZ).
Fixes: 00cfd77b90 ("mptcp: retransmit ADD_ADDR when timeout")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260505-net-mptcp-pm-fixes-7-1-rc3-v1-6-fca8091060a4@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ replaced `TCP_RTO_MAX / 8` with `HZ` ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5cd6e0ad79 ]
This mptcp_pm_add_timer() helper is executed as a timer callback in
softirq context. To avoid any data races, the socket lock needs to be
held with bh_lock_sock().
If the socket is in use, retry again soon after, similar to what is done
with the keepalive timer.
Fixes: 00cfd77b90 ("mptcp: retransmit ADD_ADDR when timeout")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260505-net-mptcp-pm-fixes-7-1-rc3-v1-3-fca8091060a4@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ applied hunk to `net/mptcp/pm_netlink.c` instead of `net/mptcp/pm.c` ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 166b783440 ]
When sending an MP_PRIO, closed subflows need to be skipped.
This fixes the case where the initial subflow got closed, re-opened
later, then an MP_PRIO is needed for the same local address.
Note that explicit MP_PRIO cannot be sent during the 3WHS, so it is fine
to use __mptcp_subflow_active().
Fixes: 067065422f ("mptcp: add the outgoing MP_PRIO support")
Cc: stable@vger.kernel.org
Fixes: b29fcfb54c ("mptcp: full disconnect implementation")
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260505-net-mptcp-pm-fixes-7-1-rc3-v1-9-fca8091060a4@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ applied to renamed function `mptcp_pm_nl_mp_prio_send_ack()` in `pm_netlink.c` ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14acf9652e ]
KASAN reproduces a slab-use-after-free in __xfrm_state_delete()'s
hlist_del_rcu calls under syzkaller load on linux-6.12.y stable
(reproduced on 6.12.47, also reachable via the same code path on
torvalds/master and on the ipsec tree). Nine unique signatures cluster
in the xfrm_state lifecycle, the load-bearing one being:
BUG: KASAN: slab-use-after-free in __hlist_del include/linux/list.h:990 [inline]
BUG: KASAN: slab-use-after-free in hlist_del_rcu include/linux/rculist.h:516 [inline]
BUG: KASAN: slab-use-after-free in __xfrm_state_delete net/xfrm/xfrm_state.c
Write of size 8 at addr ffff8881198bcb70 by task kworker/u8:9/435
Workqueue: netns cleanup_net
Call Trace:
__hlist_del / hlist_del_rcu
__xfrm_state_delete
xfrm_state_delete
xfrm_state_flush
xfrm_state_fini
ops_exit_list
cleanup_net
The other observed signatures hit the same slab object from
__xfrm_state_lookup, xfrm_alloc_spi, __xfrm_state_insert and an OOB
write variant of __xfrm_state_delete, all on the byseq/byspi
hash chains.
__xfrm_state_delete() guards its byseq and byspi unhashes with
value-based predicates:
if (x->km.seq)
hlist_del_rcu(&x->byseq);
if (x->id.spi)
hlist_del_rcu(&x->byspi);
while everywhere else in the file (e.g. state_cache, state_cache_input)
the safer hlist_unhashed() check is used. xfrm_alloc_spi() sets
x->id.spi = newspi inside xfrm_state_lock and then immediately inserts
into byspi, but a path that observes x->id.spi != 0 outside of
xfrm_state_lock can still skip-or-hit the byspi unhash inconsistently
with whether x is actually on the list. The same holds for x->km.seq
versus byseq, and the bydst/bysrc unhashes have no predicate at all,
so a second __xfrm_state_delete() on the same object writes through
LIST_POISON pprev.
The defensive change here:
- Use hlist_del_init_rcu() instead of hlist_del_rcu() on bydst,
bysrc, byseq and byspi so a second deletion is a no-op rather
than a write through LIST_POISON pprev. The byseq/byspi nodes
are already initialised in xfrm_state_alloc().
- Test hlist_unhashed() rather than the value predicate for
byseq/byspi, so the unhash decision tracks list state rather than
mutable scalar fields.
Empirical verification: applied this patch on top of v6.12.47, rebuilt,
and re-ran the same syzkaller harness for 1h16m on a previously-crashy
configuration that produced ~100 hits each of slab-use-after-free
Read in xfrm_alloc_spi / Read in __xfrm_state_lookup / Write in
__xfrm_state_delete. After the patch, 7.1M execs across 32 VMs at
~1550 exec/sec produced zero xfrm_state UAF/OOB hits. /proc/slabinfo
confirms the xfrm_state slab is actively allocated and freed during
the run (~143 KiB resident), so the fuzzer is still exercising those
code paths -- they just no longer crash.
Reproduction:
- Linux 6.12.47 x86_64 + KASAN_GENERIC + KASAN_INLINE + KCOV
- syzkaller @ 746545b8b1e4c3a128db8652b340d3df90ce61db
- 32 QEMU/KVM VMs x 2 vCPU on AWS c5.metal bare metal
- 9 unique signatures collected in ~9h, all within xfrm_state
lifecycle
Fixes: fe9f1d8779 ("xfrm: add state hashtable keyed by seq")
Fixes: 7b4dc3600e ("[XFRM]: Do not add a state whose SPI is zero to the SPI hash.")
Reported-by: Michal Kosiorek <mkosiorek121@gmail.com>
Tested-by: Michal Kosiorek <mkosiorek121@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michal Kosiorek <mkosiorek121@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
[ dropped state_cache/state_cache_input unhash hunks and xfrm_nat_keepalive_state_updated() call ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ec54093e6a ]
AH allocates its temporary auth/ICV layout differently when ESN is enabled:
the async ahash setup appends a 4-byte seqhi slot before the ICV or
auth_data area, but the async completion callbacks still reconstruct the
temporary layout as if seqhi were absent.
With an async AH implementation selected, that makes AH copy or compare
the wrong bytes on both the IPv4 and IPv6 paths. In UML repro on IPv4 AH
with ESN and forced async hmac(sha1), ping fails with 100% packet loss,
and the callback logs show the pre-fix drift:
ah4 output_done: esn=1 err=0 icv_off=20 expected_off=24
ah4 input_done: esn=1 auth_off=20 expected_auth_off=24 icv_off=32 expected_icv_off=36
Reconstruct the callback-side layout the same way the setup path built it
by skipping the ESN seqhi slot before locating the saved auth_data or ICV.
Per RFC 4302, the ESN high-order 32 bits participate in the AH ICV
computation, so the async callbacks must account for the seqhi slot.
Post-fix, the same IPv4 AH+ESN+forced-async-hmac(sha1) UML repro shows
the corrected offset (ah4 output_done: esn=1 err=0 icv_off=24
expected_off=24) and ping succeeds; net/ipv4/ah4.o and net/ipv6/ah6.o
build clean at W=1. IPv6 AH+ESN was not exercised at runtime, and the
change has not been tested against a real async hardware AH engine.
Fixes: d4d573d033 ("{IPv4,xfrm} Add ESN support for AH egress part")
Fixes: d8b2a8600b ("{IPv4,xfrm} Add ESN support for AH ingress part")
Fixes: 26dd70c3fa ("{IPv6,xfrm} Add ESN support for AH egress part")
Fixes: 8d6da6f325 ("{IPv6,xfrm} Add ESN support for AH ingress part")
Cc: stable@vger.kernel.org
Assisted-by: Codex:gpt-5-4
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0a6bfaa0e6 ]
Now that the alignmask for ahash and shash algorithms is always 0,
crypto_ahash_alignmask() always returns 0 and will be removed. In
preparation for this, stop checking crypto_ahash_alignmask() in ah6.c.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: ec54093e6a ("xfrm: ah: account for ESN high bits in async callbacks")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e77f5dd701 ]
Now that the alignmask for ahash and shash algorithms is always 0,
crypto_ahash_alignmask() always returns 0 and will be removed. In
preparation for this, stop checking crypto_ahash_alignmask() in ah4.c.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: ec54093e6a ("xfrm: ah: account for ESN high bits in async callbacks")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 85fa351204 ]
hci_conn lookup and field access must be covered by hdev lock in
hci_user_passkey_notify_evt() and hci_keypress_notify_evt(), otherwise
the connection can be freed concurrently.
Extend the hci_dev_lock critical section to cover all conn usage in both
handlers.
Keep the existing keypress notification behavior unchanged by routing
the early exits through a common unlock path.
Fixes: 92a25256f1 ("Bluetooth: mgmt: Implement support for passkey notification")
Cc: stable@vger.kernel.org
Signed-off-by: Shuvam Pandey <shuvampandey1@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df46016532 ]
Local FDB entries can be rewritten in place by `fdb_delete_local()`, which
updates `f->dst` to another port or to `NULL` while keeping the entry
alive. Several bridge RCU readers inspect `f->dst`, including
`br_fdb_fillbuf()` through the `brforward_read()` sysfs path.
These readers currently load `f->dst` multiple times and can therefore
observe inconsistent values across the check and later dereference.
In `br_fdb_fillbuf()`, this means a concurrent local-FDB update can change
`f->dst` after the NULL check and before the `port_no` dereference,
leading to a NULL-ptr-deref.
Fix this by taking a single `READ_ONCE()` snapshot of `f->dst` in each
affected RCU reader and using that snapshot for the rest of the access
sequence. Also publish the in-place `f->dst` updates in `fdb_delete_local()`
with `WRITE_ONCE()` so the readers and writer use matching access patterns.
Fixes: 960b589f86 ("bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address")
Cc: stable@kernel.org
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Co-developed-by: Yuan Tan <yuantan098@gmail.com>
Signed-off-by: Yuan Tan <yuantan098@gmail.com>
Suggested-by: Xin Liu <bird@lzu.edu.cn>
Tested-by: Ren Wei <enjou1224z@gmail.com>
Signed-off-by: Zhengchuan Liang <zcliangcn@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/6570fabb85ecadb8baaf019efe856f407711c7b9.1776043229.git.zcliangcn@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
[ kept combined-flag check `(dst->flags & (BR_PROXYARP_WIFI | BR_NEIGH_SUPPRESS))` and `cb->args[2]` indexing instead of `br_is_neigh_suppress_enabled()` helper and `ctx->fdb_idx` ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27d5e84e81 ]
Currently, the nameserver doesn't limit the number of nodes it handles.
This can be an attack vector if a malicious client starts registering
random nodes, leading to memory exhaustion.
Hence, limit the maximum number of nodes to 64. Note that, limit of 64 is
chosen based on the current platform requirements. If requirement changes
in the future, this limit can be increased.
Cc: stable@vger.kernel.org
Fixes: 0c2204a4ad ("net: qrtr: Migrate nameservice to kernel from userspace")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://patch.msgid.link/20260409-qrtr-fix-v3-4-00a8a5ff2b51@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ dropped node_count-- hunk since ctrl_cmd_bye() has no delete_node ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a663bac71a ]
>From the MCTP Base specification (DSP0236 v1.2.1), the first byte of
the MCTP header contains a 4 bit reserved field, and 4 bit version.
On our current receive path, we require those 4 reserved bits to be
zero, but the 9500-8i card is non-conformant, and may set these
reserved bits.
DSP0236 states that the reserved bits must be written as zero, and
ignored when read. While the device might not conform to the former,
we should accept these message to conform to the latter.
Relax our check on the MCTP version byte to allow non-zero bits in the
reserved field.
Fixes: 889b7da23a ("mctp: Add initial routing framework")
Signed-off-by: Yuan Zhaoming <yuanzm2@lenovo.com>
Cc: stable@vger.kernel.org
Acked-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260417141340.5306-1-yuanzhaoming901030@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 68efba3644 ]
A node sends the BYE packet when it is about to go down. So the nameserver
should advertise the removal of the node to all remote and local observers
and free the node finally. But currently, the nameserver doesn't free the
node memory even after processing the BYE packet. This causes the node
memory to leak.
Hence, remove the node from Xarray list and free the node memory during
both success and failure case of ctrl_cmd_bye().
Cc: stable@vger.kernel.org
Fixes: 0c2204a4ad ("net: qrtr: Migrate nameservice to kernel from userspace")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://patch.msgid.link/20260409-qrtr-fix-v3-3-00a8a5ff2b51@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 608a147a88 ]
There is a use after free scenario while iterating through the servers
radix tree despite the ns being a single threaded process. This can
happen when the radix tree APIs are not synchronized with the
rcu_read_lock() APIs.
Convert the radix tree for servers to xarray to take advantage of the
built in rcu lock usage provided by xarray.
Signed-off-by: Chris Lew <quic_clew@quicinc.com>
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 68efba3644 ("net: qrtr: ns: Free the node during ctrl_cmd_bye()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5640227d9a ]
Current code does no bound checking on the number of lookups a client can
perform. Though the code restricts the lookups to local clients, there is
still a possibility of a malicious local client sending a flood of
NEW_LOOKUP messages over the same socket.
Fix this issue by limiting the maximum number of lookups to 64 globally.
Since the nameserver allows only atmost one local observer, this global
lookup count will ensure that the lookups stay within the limit.
Note that, limit of 64 is chosen based on the current platform
requirements. If requirement changes in the future, this limit can be
increased.
Cc: stable@vger.kernel.org
Fixes: 0c2204a4ad ("net: qrtr: Migrate nameservice to kernel from userspace")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://patch.msgid.link/20260409-qrtr-fix-v3-2-00a8a5ff2b51@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ adapted comment block to only mention QRTR_NS_MAX_LOOKUPS and kept kzalloc() instead of kzalloc_obj() due to missing prerequisite commits ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c054e17d9 ]
In tpacket_snd(), when PACKET_VNET_HDR is enabled, vnet_hdr points
directly into the mmap'd TX ring buffer shared with userspace. The
kernel validates the header via __packet_snd_vnet_parse() but then
re-reads all fields later in virtio_net_hdr_to_skb(). A concurrent
userspace thread can modify the vnet_hdr fields between validation
and use, bypassing all safety checks.
The non-TPACKET path (packet_snd()) already correctly copies vnet_hdr
to a stack-local variable. All other vnet_hdr consumers in the kernel
(tun.c, tap.c, virtio_net.c) also use stack copies. The TPACKET TX
path is the only caller of virtio_net_hdr_to_skb() that reads directly
from user-controlled shared memory.
Fix this by copying vnet_hdr from the mmap'd ring buffer to a
stack-local variable before validation and use, consistent with the
approach used in packet_snd() and all other callers.
Fixes: 1d036d25e5 ("packet: tpacket_snd gso and checksum offload")
Signed-off-by: Bingquan Chen <patzilla007@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260418112006.78823-1-patzilla007@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ replaced `vnet_hdr_sz` with `sizeof(vnet_hdr)` and `if (vnet_hdr_sz)` with `if (po->has_vnet_hdr)` ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46d0d6f50d upstream.
To prevent timing attacks, MACs need to be compared in constant
time. Use the appropriate helper function for this.
Fixes: cfb6eeb4c8 ("[TCP]: MD5 Signature Option (RFC2385) support.")
Fixes: 658ddaaf66 ("tcp: md5: RST: getting md5 key from listener")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Link: https://patch.msgid.link/20260302203409.13388-1-ebiggers@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Li hongliang <1468888505@139.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5f8a90ac9 upstream.
When ADD_OUT_STREAMS is denied, SCTP only shrinks the queued chunks and
then lowers outcnt. That leaves removed stream metadata behind, so a
later re-add can reuse a stale ext and hit a null-pointer dereference in
the scheduler get path.
Fix the rollback by tearing down the removed stream state the same way
other stream resizes do. Unschedule the current scheduler state, drop
the removed stream ext state with sctp_stream_outq_migrate(), and then
reschedule the remaining streams.
This keeps scheduler-private RR/FC/PRIO lists consistent while fully
rolling back denied outgoing stream additions.
Fixes: 637784ade2 ("sctp: introduce priority based stream scheduler")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Zhengchuan Liang <zcliangcn@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Signed-off-by: Wyatt Feng <bronzed_45_vested@icloud.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/d78954ecd94954653ee299400e98d74a03a6f7d3.1780603399.git.bronzed_45_vested@icloud.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5eba3e48d7 upstream.
The SCTP exact sock_diag lookup can hold a transport reference, block on
lock_sock(sk), and then resume after sctp_association_free() has marked
the association dead and freed its bind address list.
When that happens, inet_assoc_attr_size() and
inet_diag_msg_sctpasoc_fill() can still dereference association state
that is no longer valid for reporting. In particular,
inet_diag_msg_sctpasoc_fill() may read an empty bind-address list as a
real sctp_sockaddr_entry and trigger an out-of-bounds read from
unrelated association memory.
Reject the association after taking the socket lock if it has been
reaped or detached from the endpoint, and report the lookup as stale.
This keeps the exact dump-one path from formatting torn association
state.
Fixes: 8f840e47f1 ("sctp: add the sctp_diag.c file")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Zhengchuan Liang <zcliangcn@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Signed-off-by: Zhao Zhang <zzhan461@ucr.edu>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/fac6043fa20a2ff68e12958c431836f692c51268.1780113823.git.zzhan461@ucr.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20cf0fb715 upstream.
The RDS IB connection teardown path is written so it can run during
partial startup and on repeated shutdown attempts. It uses NULL
pointers to distinguish resources that are still owned from resources
that have already been released.
When rds_ib_setup_qp() fails after allocating i_sends but before
allocating i_recvs, the sends_out path frees i_sends without clearing
the pointer. A later shutdown pass can still treat that stale pointer
as a live send ring allocation.
Clear i_sends after vfree() in the error unwind path so the existing
shutdown logic continues to use the correct ownership state.
Fixes: 3b12f73a5c ("rds: ib: add error handle")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Zhengchuan Liang <zcliangcn@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Signed-off-by: Yuqi Xu <xuyq21@lenovo.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Reviewed-by: Allison Henderson <achender@kernel.org>
Link: https://patch.msgid.link/5a0f7624bb9845a7b67d26166a150b59e7f394ce.1779632468.git.xuyq21@lenovo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c05fa14db4 upstream.
When vmci_transport_recv_connecting_server() returns an error,
vmci_transport_recv_listen() calls vsock_remove_pending() but never
calls sk_acceptq_removed(). This leaves sk_ack_backlog incremented
permanently.
Repeated handshake failures (malformed packets, queue pair alloc
failure, event subscribe failure) cause sk_ack_backlog to climb
toward sk_max_ack_backlog. Once it reaches the limit the listener
permanently refuses all new connections with -ECONNREFUSED, a
silent denial of service requiring a process restart to recover.
The two existing sk_acceptq_removed() calls in af_vsock.c do not
cover this path: line 764 checks vsock_is_pending() which returns
false after vsock_remove_pending(), and line 1889 is only reached
on successful accept().
Fix by balancing sk_acceptq_added() with sk_acceptq_removed() on
the error path.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Cc: stable@vger.kernel.org
Signed-off-by: Raf Dickson <rafdog35@gmail.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/20260526104356.469928-1-rafdog35@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57132affbc upstream.
sock_set_timestamping() can fail for different reasons. The returned
value should then be checked.
If sock_set_timestamping() fails for at least one subflow, the first
error is now reported to the userspace, similar to what is done with
other socket options.
Fixes: 9061f24bf8 ("mptcp: sockopt: propagate timestamp request to subflows")
Cc: stable@vger.kernel.org
Reported-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Closes: https://lore.kernel.org/willemdebruijn.kernel.178a41a53d041@gmail.com
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260602-net-mptcp-misc-fixes-7-1-rc7-v2-7-856831229976@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1918b36ed upstream.
Sashiko noted that retransmission with csum enabled can actually
transmit new data, but currently the relevant code does not update
accordingly snd_nxt.
The may cause incoming ack drop and an endless retransmission loop.
Address the issue incrementing snd_nxt as needed.
Fixes: 4e14867d5e ("mptcp: tune re-injections for csum enabled mode")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260602-net-mptcp-misc-fixes-7-1-rc7-v2-2-856831229976@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c381039ade upstream.
espintcp keeps a single in-flight transmit in ctx->partial.
Before building a new sk_msg, espintcp_sendmsg() first tries to flush
that state through espintcp_push_msgs().
For blocking callers, espintcp_push_msgs() may return success even when
the previous partial send is still pending. espintcp_sendmsg() would
then reinitialize emsg->skmsg and reuse ctx->partial while the old
transfer still owns that state.
Do not rebuild the send message when ctx->partial is still in progress.
If espintcp_push_msgs() returns with emsg->len still set, fail the new
send instead of overwriting the live partial state.
This is a memory-safety fix: reusing the live partial-send state can
leave a stale offset attached to a new sk_msg and lead to an out-of-
bounds read in the send path.
tcp_sendmsg_locked() already handles waiting for send buffer memory, so
the fix here is just to preserve espintcp's one-message-at-a-time
transmit state.
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Zhengchuan Liang <zcliangcn@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Assisted-by: Codex:GPT-5.4
Signed-off-by: Wyatt Feng <bronzed_45_vested@icloud.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd21473354 upstream.
net/bluetooth/l2cap_core.c:l2cap_sig_channel() accepts BR/EDR
signaling packets up to the channel MTU and dispatches each command
without enforcing the signaling MTU (MTUsig). A Bluetooth BR/EDR peer
within radio range can send a fixed-channel CID 0x0001 packet that is
larger than MTUsig and contains many L2CAP_ECHO_REQ commands before
pairing. In a real-radio stock-kernel run, one 681-byte signaling
packet containing 168 zero-length ECHO_REQ commands made the target
transmit 168 ECHO_RSP frames over about 220 ms.
Impact: a Bluetooth BR/EDR peer within radio range, before pairing, can
force 168 ECHO_RSP frames from one 681-byte fixed-channel signaling
packet containing packed ECHO_REQ commands.
Define Linux's BR/EDR signaling MTU as the spec minimum of 48 bytes and
reject any larger signaling packet with one L2CAP_COMMAND_REJECT_RSP
carrying L2CAP_REJ_MTU_EXCEEDED before any command is dispatched.
The Bluetooth Core spec wording for MTUExceeded says the reject
identifier shall match the first request command in the packet, and
that packets containing only responses shall be silently discarded.
Linux intentionally deviates from that prescription: silently
discarding desynchronizes the peer because the remote stack never
learns its responses were dropped, and locating the first request
command requires walking command headers past MTUsig, i.e. processing
bytes from a packet we have already decided is too large to process.
We therefore always emit one reject and use the identifier from the
first command header, a single fixed-offset byte read.
The unrestricted BR/EDR signaling parser and ECHO_REQ response path both
trace to the initial git import; no later introducing commit is
available for a Fixes tag.
Cc: stable@vger.kernel.org
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20260518002800.1361430-1-michael.bommarito@gmail.com
Link: https://lore.kernel.org/r/20260520135034.1060859-1-michael.bommarito@gmail.com
Link: https://lore.kernel.org/r/20260521000555.3712030-1-michael.bommarito@gmail.com
Assisted-by: Claude:claude-opus-4-7
Assisted-by: Codex:gpt-5-5-xhigh
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
