[ Upstream commit 66725039f7 ]
mms114_interrupt() reads a packet of touch data from the device into a
fixed-size on-stack buffer
struct mms114_touch touch[MMS114_MAX_TOUCH];
which holds MMS114_MAX_TOUCH (10) events of MMS114_EVENT_SIZE (8) bytes,
i.e. 80 bytes. The length of the I2C read into it is taken verbatim from
the device:
packet_size = mms114_read_reg(data, MMS114_PACKET_SIZE);
if (packet_size <= 0)
goto out;
...
error = __mms114_read_reg(data, MMS114_INFORMATION, packet_size,
(u8 *)touch);
packet_size is a single device register byte (0x0F) and the only check
is the lower bound packet_size <= 0; it is never bounded against the
size of touch[]. A malfunctioning, malicious or counterfeit controller
(or an attacker tampering with the I2C bus) can report a packet_size of
up to 255, so __mms114_read_reg() writes up to 175 bytes past the end of
touch[] on the IRQ-thread stack: a stack out-of-bounds write that can
overwrite the stack canary, saved registers and the return address.
A well-formed device never reports more than the buffer holds, so reject
an oversized packet and drop the report, consistent with the handler's
other error paths, rather than reading past the buffer.
Fixes: 07b8481d4a ("Input: add MELFAS mms114 touchscreen driver")
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260612-b4-disp-dc4b8dc4-v1-1-d7cb0a828d92@proton.me
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[ changed `&client->dev` to `&data->client->dev` since 6.1's interrupt handler lacks the `client` local variable ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a6ac4e24c1 ]
The MMS134S and MMS136 touch controllers have an event size of 6 bytes
rather than 8 bytes. When __mms114_read_reg() reads the touch data
packet from the device into the touch buffer, the events are packed
tightly at 6-byte intervals. However, the driver iterates through the
events using standard C array indexing (touch[index]), where each
element is sizeof(struct mms114_touch) (8 bytes) apart. As a result, any
touch events beyond the first one are read from incorrect offsets and
parsed improperly.
Fix this by explicitly calculating the byte offset for each touch event
based on the device's specific event size.
Fixes: 53fefdd1d3 ("Input: mms114 - support MMS136")
Fixes: ab10867819 ("Input: mms114 - support MMS134S")
Reported-by: sashiko-bot@kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Reviewed-by: Bryam Vargas <hexlabsecurity@proton.me>
Link: https://patch.msgid.link/20260616050912.1531241-1-dmitry.torokhov@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 062dc4693e upstream.
In sur40_probe(), if video_register_device() fails, the error path jumps to
err_unreg_video. This incorrectly attempts to unregister a video device
that was never successfully registered, and fails to free the V4L2 control
handler (v4l2_ctrl_handler_free) that was initialized immediately prior.
Fix this by introducing an err_free_ctrl label to properly free the V4L2
control handler and bypass video_unregister_device() when video device
registration fails.
Reported-by: sashiko-bot@kernel.org
Cc: stable@vger.kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260616051235.1549517-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9da976eb64 upstream.
In sur40_probe(), input_register_device() was previously called early before
the V4L2 video device and vb2_queue components were fully initialized. If
userspace opened the input device immediately upon registration, sur40_open()
would trigger and start the sur40_poll() worker thread. This worker thread
invokes sur40_process_video() and accesses the uninitialized vb2_queue
structure, leading to a data race and potential system crash.
Furthermore, if V4L2 or video registration failed after input_register_device()
succeeded, the error path fell through to calling input_free_device() on a
successfully registered device instead of input_unregister_device(), corrupting
input core state.
Move input_register_device() to the very end of sur40_probe(). This ensures
the V4L2 and video queue structures are fully initialized before polling can
start, and naturally resolves the error path bug since input_free_device()
is now only called when input registration has not yet occurred.
To maintain strict LIFO (Last-In, First-Out) teardown ordering, also move
input_unregister_device() to the very beginning of sur40_disconnect(). This
guarantees that the input polling worker thread is stopped before V4L2
video components or control handlers are unregistered.
Reported-by: sashiko-bot@kernel.org
Cc: stable@vger.kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260616051235.1549517-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adea84ee6c upstream.
If the touchscreen controller reports a touch ID of 0, the driver
calculates the slot ID as touch->id - 1, which underflows to UINT_MAX.
This is passed to input_mt_slot() as -1.
Since the input core ignores negative slot values, the active slot remains
unchanged. The driver then reports the touch coordinates for the previously
active slot, corrupting its state.
Fix this by rejecting touch reports with ID 0.
Fixes: 07b8481d4a ("Input: add MELFAS mms114 touchscreen driver")
Cc: stable@vger.kernel.org
Reported-by: sashiko-bot@kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260704060115.353049-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 478cdd736f upstream.
tw_interrupt() accumulates each non-zero serial byte into a fixed
three-byte buffer with a running index that is only reset once a full
packet has been received *and* the device's two Y bytes agree:
tw->data[tw->idx++] = data;
if (tw->idx == TW_LENGTH && tw->data[1] == tw->data[2]) {
...
tw->idx = 0;
}
The reset is gated on tw->data[1] == tw->data[2], a value the device
controls. A malicious, malfunctioning or counterfeit Touchwindow
peripheral can stream non-zero bytes whose 2nd and 3rd bytes differ: the
index reaches TW_LENGTH without the equality holding, is never reset, and
keeps growing, so tw->data[tw->idx++] walks off the end of the three-byte
array and the rest of the heap-allocated struct tw, one attacker-chosen
byte at a time -- an unbounded, device-driven heap out-of-bounds write.
Reset the index on every completed packet and report an event only when
the two Y bytes match, like the other serio touchscreen drivers do.
Fixes: 11ea3173d5 ("Input: add driver for Touchwin serial touchscreens")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Link: https://patch.msgid.link/20260613-b4-disp-69921bfd-v1-1-82c036899959@proton.me
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ed62a96e0 upstream.
goodix_ts_read_input_report() copies the number of touch points reported
by the device into an on-stack buffer
u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
which is sized for at most GOODIX_MAX_CONTACTS (10) contacts. The only
runtime check bounds the per-interrupt count against ts->max_touch_num,
but that value is taken verbatim from a 4-bit field of the device
configuration block and is never clamped:
ts->max_touch_num = ts->config[MAX_CONTACTS_LOC] & 0x0f;
The nibble can be 0..15, so a malfunctioning, malicious or counterfeit
controller (or an attacker tampering with the I2C bus) can advertise up
to 15 contacts. goodix_ts_read_input_report() then accepts a touch_num
of up to 15 and the second goodix_i2c_read() writes
ts->contact_size * (touch_num - 1) bytes past the one-contact header into
point_data - up to 30 bytes (45 with the 9-byte report format) beyond the
92-byte buffer: a stack out-of-bounds write.
Clamp max_touch_num to GOODIX_MAX_CONTACTS, the number of contacts
point_data[] is sized for, when reading it from the configuration.
Fixes: a7ac7c95d4 ("Input: goodix - use max touch number from device config")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Link: https://patch.msgid.link/20260612-b4-disp-6844625d-v1-1-df0aed080c9d@proton.me
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baa0210fb6 upstream.
When a configuration file provides an object size that is larger than the
driver's known mxt_obj_size(object), the driver intends to discard the
extra bytes.
The loop iterates using for (i = 0; i < size; i++). Inside the loop, the
condition to skip processing extra bytes is:
if (i > mxt_obj_size(object))
continue;
Since i is a 0-based index, the valid indices for the object are 0 through
mxt_obj_size(object) - 1.
When i == mxt_obj_size(object), the condition evaluates to false, and the
code processes the byte instead of discarding it.
This causes the code to calculate byte_offset = reg + i - cfg->start_ofs
and writes the byte there, overwriting exactly one byte of the adjacent
instance or object.
Update the boundary check to skip extra bytes correctly by using >=.
Fixes: 50a77c658b ("Input: atmel_mxt_ts - download device config using firmware loader")
Cc: stable@vger.kernel.org
Assisted-by: Gemini:gemini-3.1-pro
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://patch.msgid.link/20260504185448.4055973-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2905281cbd upstream.
nexio_read_data() pulls data_len and x_len from a packed __be16 header
in the device's interrupt packet and then walks packet->data[0..x_len)
and packet->data[x_len..data_len) comparing each byte against a
threshold.
Both fields are 16-bit on the wire (max 65535). The existing
adjustments shave at most 0x100 / 0x80 off, so the loop bound can still
reach roughly 0xfeff. The URB transfer buffer for NEXIO is rept_size
(1024) bytes from usb_alloc_coherent(), with the first 7 occupied by the
packed header — so packet->data[] has 1017 valid bytes. read_data()
callbacks are not given urb->actual_length, and nothing else bounds the
walk.
A device that lies about its length can get a ~64 KiB out-of-bounds read
past the coherent DMA allocation. The first index whose byte exceeds
NEXIO_THRESHOLD lands in begin_x / begin_y and from there into the
reported touch coordinates, so adjacent kernel memory contents leak to
userspace as ABS_X / ABS_Y events. Far enough out, the read can also
hit an unmapped page and fault.
Fix this all by clamping data_len to the buffer's data[] capacity and
x_len to data_len.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 5197424cdc ("Input: usbtouchscreen - add NEXIO (or iNexio) support")
Cc: stable <stable@kernel.org>
Assisted-by: gkh_clanker_t1000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026042026-chlorine-epidermis-fd6d@gregkh
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 248d3a73a0 upstream.
The current validation 'wire_order[i] > ARRAY_SIZE(config_pins)' allows
wire_order[i] to equal ARRAY_SIZE(config_pins), which causes out-of-bounds
access when used as index in 'config_pins[wire_order[i]]'.
Since config_pins has 4 elements (indices 0-3), the valid range for
wire_order should be 0-3. Fix the off-by-one error by using >= instead
of > in the validation check.
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Link: https://patch.msgid.link/20251114062817.852698-1-junjie.cao@intel.com
Fixes: bb76dc09dd ("input: ti_am33x_tsc: Order of TSC wires, made configurable")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb04e8b1d2 ]
We only had a couple of array[] declarations, and changing them to just
use 'MAX()' instead of 'max()' fixes the issue.
This will allow us to simplify our min/max macros enormously, since they
can now unconditionally use temporary variables to avoid using the
argument values multiple times.
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eliav Farber <farbere@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7866ee0a9 upstream.
The reset GPIO is not toggled in any critical section where it couldn't
sleep, allow the reset GPIO to sleep. This allows the driver to operate
reset GPIOs connected to I2C GPIO expanders.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Link: https://lore.kernel.org/r/20251005023335.166483-1-marek.vasut@mailbox.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d176708ffc upstream.
Use the new soc_intel_is_byt() helper from linux/platform_data/x86/soc.h.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131143539.109142-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 208989744a ]
Ensure that the touchscreen response has correct "report id" byte
before processing the touch data and discard other messages.
Fixes: 42370681bd ("Input: Add support for ILITEK Lego Series")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240805085511.43955-3-francesco@dolcini.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d0b18cd5d ]
For different reasons i2c transaction may fail or report id in the
message may be wrong. Avoid closing the frame in this case as it will
result in all contacts being dropped, indicating that nothing is
touching the screen anymore, while usually it is not the case.
Fixes: 42370681bd ("Input: Add support for ILITEK Lego Series")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240805085511.43955-2-francesco@dolcini.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccbfea78ad ]
In case the touch controller is not connected, this message keeps scrolling
on the console indefinitelly. Ratelimit it to avoid filling kernel logs.
"
ads7846 spi2.1: spi_sync --> -22
"
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240708211913.171243-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38a38f5a36 ]
When support for Silead touchscreens was orginal added some touchscreens
with older firmware versions only supported 5 fingers and this was made
the default requiring the setting of a "silead,max-fingers=10" uint32
device-property for all touchscreen models which do support 10 fingers.
There are very few models with the old 5 finger fw, so in practice the
setting of the "silead,max-fingers=10" is boilerplate which needs to
be copy and pasted to every touchscreen config.
Reporting that 10 fingers are supported on devices which only support
5 fingers doesn't cause any problems for userspace in practice, since
at max 4 finger gestures are supported anyways. Drop the max_fingers
configuration and simply always assume 10 fingers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20240525193854.39130-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f0fad0382 ]
The caller of this function treats all non-zero values as an error, so
the return value of i2c_master_recv() cannot be returned directly.
This fixes touch reporting when there are more than 6 active touches.
Fixes: ef536abd3a ("Input: ili210x - define and use chip operations structure")
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Link: https://lore.kernel.org/r/20240523085624.2295988-1-jkeeping@inmusicbrands.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa9f4275b2 ]
To discard false readings, one should use "ti,penirq-recheck-delay-usecs".
Checking get_pendown_state() at the beginning, most of the time fails
causing malfunctioning.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230126105227.47648-4-l.ellero@asem.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13f82ca387 ]
Controllers that report pressure (e.g. ADS7846) use 5 commands and the
correct sequence is READ_X, READ_Y, READ_Z1, READ_Z2, PWRDOWN.
Controllers that don't report pressure (e.g. ADS7845/ADS7843) use only 3
commands and the correct sequence should be READ_X, READ_Y, PWRDOWN. But
the sequence sent was incorrect: READ_X, READ_Y, READ_Z1.
Fix this by setting the third (and last) command to PWRDOWN.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230126105227.47648-3-l.ellero@asem.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 423622a90a upstream.
Add a special case for gpio_count == 1 && gpio_int_idx == 0 to
goodix_add_acpi_gpio_mappings().
It seems that on newer x86/ACPI devices the reset and irq GPIOs are no
longer listed as GPIO resources instead there is only 1 GpioInt resource
and _PS0 does the whole reset sequence for us.
This means that we must call acpi_device_fix_up_power() on these devices
to ensure that the chip is reset before we try to use it.
This part was already fixed in commit 3de93e6ed2 ("Input: goodix - call
acpi_device_fix_up_power() in some cases") by adding a call to
acpi_device_fix_up_power() to the generic "Unexpected ACPI resources"
catch all.
But it turns out that this case on some hw needs some more special
handling. Specifically the firmware may bootup with the IRQ pin in
output mode. The reset sequence from ACPI _PS0 (executed by
acpi_device_fix_up_power()) should put the pin in input mode,
but the GPIO subsystem has cached the direction at bootup, causing
request_irq() to fail due to gpiochip_lock_as_irq() failure:
[ 9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0
[ 9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060
[ 9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8
[ 9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ
[ 9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio
[ 9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5
Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0
which adds an ACPI GPIO lookup table for the int GPIO even though we cannot
use it for reset purposes (as there is no reset GPIO).
Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call
succeed, which will explicitly set the direction to input fixing the issue.
Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since
there is only 1 GPIO in the ACPI resources the reset entry in that
lookup table will amount to a no-op.
Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5bca3688bd ]
rpi_firmware_get() take reference, we need to release it in error paths
as well. Use devm_rpi_firmware_get() helper to handling the resources.
Also remove the existing rpi_firmware_put().
Fixes: 0b9f28fed3 ("Input: add official Raspberry Pi's touchscreen driver")
Fixes: 3b8ddff780 ("input: raspberrypi-ts: Release firmware handle when not needed")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20221223074657.810346-1-linmq006@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8a0432bab6 upstream.
The Android Lenovo Yoga Book X90F / X90L uses the same goodix touchscreen
with 9 bytes touch reports for its touch keyboard as the already supported
Windows Lenovo Yoga Book X91F/L, add a DMI match for this to
the nine_bytes_report DMI table.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230315134442.71787-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a85fbd6498 ]
As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.
We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:
devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.
Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).
Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.
Fixes: afe10358e4 ("Input: elants_i2c - wire up regulator support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221117123805.1.I9959ac561dd6e1e8e1ce7085e4de6167b27c574f@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e37cc624 ]
On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.
On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.
To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().
This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 425fe4709c ]
This controller is used by PinePhone and PinePhone Pro. Support for
the PinePhone Pro will be added in a later patch set.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Jarrah Gosbell <kernel@undef.tools>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220809091200.290492-1-kernel@undef.tools
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6bb7144c3f upstream.
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 102feb1ddf ("Input: exc3000 - factor out vendor data request")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220411105828.22140-1-linmq006@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a2fd46cd3d ]
Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.
Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.
But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca9 ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").
And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.
This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 209bda4741 ]
Refactor reset handling a bit, change the main reset handler
into a new goodix_reset_no_int_sync() helper and add a
goodix_reset() wrapper which calls goodix_int_sync()
separately.
Also push the dev_err() call on reset failure into the
goodix_reset_no_int_sync() and goodix_int_sync() functions,
so that we don't need to have separate dev_err() calls in
all their callers.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2233cb7b6 ]
Add a goodix.h header file, and move the register definitions,
and struct declarations there and add prototypes for various
helper functions.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Since MAINTAINERS needs updating because of this change anyways,
also add myself as co-maintainer.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31ae0102a3 ]
Change the type of the goodix_i2c_write() len parameter to from 'unsigned'
to 'int' to avoid bare use of 'unsigned', changing it to 'int' makes
goodix_i2c_write()' prototype consistent with goodix_i2c_read().
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f76955ab1 ]
The commit 26623eea0d attempted to deal with potential leak of runtime
PM counter when opening the touchscreen device, however it ended up
erroneously dropping the counter in the case of successfully enabling the
device.
Let's address this by using pm_runtime_resume_and_get() and then executing
pm_runtime_put_sync() only when we fail to send "sense on" command to the
device.
Fixes: 26623eea0d ("Input: stmfts - fix reference leak in stmfts_input_open")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e4920d42ce upstream.
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Fixes: 201f3c8035 ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26623eea0d ]
pm_runtime_get_sync() will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in stmfts_input_open, so we should fix it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220317131604.53538-1-zhengyongjun3@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e941dc13fd ]
I observed the following problem with the BT404 touch pad
running the Phosh UI:
When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".
After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).
DOWN
Zinitix-TS 3-0020: finger 0 down (246, 395)
Zinitix-TS 3-0020: finger 1 up (0, 0)
Zinitix-TS 3-0020: finger 2 down (246, 395)
Zinitix-TS 3-0020: finger 3 up (0, 0)
Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
Zinitix-TS 3-0020: finger 0 up (246, 395)
Zinitix-TS 3-0020: finger 2 up (246, 395)
Zinitix-TS 3-0020: finger 4 up (246, 395)
This is one touch and release: i.e. this is all reported on
touch (down) and release.
There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.
Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.
Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.
Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.
After this my Zinitix BT404 touchscreen report fingers
flawlessly.
The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:
if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;
As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bfeb6c21e ]
The Z2 step configuration doesn't erase the SEL_INP_SWC_3_0 bit-field
before setting the ADC channel. This way its value could be corrupted by
the ADC channel selected for the Z1 coordinate.
Fixes: 8c896308fe ("input: ti_am335x_adc: use only FIFO0 and clean up a little")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-3-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73cca71a90 ]
As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".
Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.
Fixes: 1b8be32e69 ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf73ed894e ]
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c8 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 81e818869b upstream.
Add d->model mapping for the "9111" model, this fixes uses using
a wrong config_len of 240 bytes while the "9111" model uses
only 186 bytes of config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206164747.197309-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ebfee2bbc upstream.
The eKTH3900/eKTH5312 series do not support the firmware update rules of
Remark ID. Exclude these two series from checking it when updating the
firmware in touch controllers.
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Link: https://lore.kernel.org/r/1639619603-20616-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12f247ab59 upstream.
The "id_buf" buffer is stored in "data->raw_info_block" and freed by
"mxt_free_object_table" in case of error.
Return instead of jumping to avoid a double free.
Addresses-Coverity-ID: 1474582 ("Double free")
Fixes: 068bdb67ef ("Input: atmel_mxt_ts - fix the firmware update")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20211212194257.68879-1-jose.exposito89@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2667f6b7af ]
I have a ST1633 touch controller which fails to probe due to a timeout
waiting for the controller to become ready. Increasing the minimum
delay to 100ms ensures that the probe sequence completes successfully.
The ST1633 datasheet says nothing about the maximum delay here and the
ST1232 I2C protocol document says "wait until" with no notion of a
timeout.
Since this only runs once during probe, being generous with the timout
seems reasonable and most likely the device will become ready
eventually.
(It may be worth noting that I saw this issue with a PREEMPT_RT patched
kernel which probably has tighter wakeups from usleep_range() than other
preemption models.)
Fixes: f605be6a57 ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210929152609.2421483-1-john@metanate.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull input fixes from Dmitry Torokhov:
- a new product ID for the xpad joystick driver
- fixes to resistive-adc-touch and snvs_pwrkey drivers
- a change to touchscreen helpers to make clang happier
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: touchscreen - avoid bitwise vs logical OR warning
Input: xpad - add support for another USB ID of Nacon GC-100
Input: resistive-adc-touch - fix division by zero error on z1 == 0
Input: snvs_pwrkey - add clk handling
For proper pressure calculation we need at least x and z1 to be non
zero. Even worse, in case z1 we may run in to division by zero
error.
Fixes: 60b7db914d ("Input: resistive-adc-touch - rework mapping of channels")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20211007095727.29579-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- several device tree bindings for input devices have been converted to
yaml
- dropped no longer used ixp4xx-beeper and CSR Prima2 PWRC drivers
- analog joystick has been converted to use ktime API and no longer
warn about low resolution timers
- a few driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (24 commits)
Input: analog - always use ktime functions
Input: mms114 - support MMS134S
Input: elan_i2c - reduce the resume time for controller in Whitebox
Input: edt-ft5x06 - added case for EDT EP0110M09
Input: adc-keys - drop bogus __refdata annotation
Input: Fix spelling mistake in Kconfig "useable" -> "usable"
Input: Fix spelling mistake in Kconfig "Modul" -> "Module"
Input: remove dead CSR Prima2 PWRC driver
Input: adp5589-keys - use the right header
Input: adp5588-keys - use the right header
dt-bindings: input: tsc2005: Convert to YAML schema
Input: ep93xx_keypad - prepare clock before using it
dt-bindings: input: sun4i-lradc: Add wakeup-source
dt-bindings: input: Convert Regulator Haptic binding to a schema
dt-bindings: input: Convert Pixcir Touchscreen binding to a schema
dt-bindings: input: Convert ChipOne ICN8318 binding to a schema
Input: pm8941-pwrkey - fix comma vs semicolon issue
dt-bindings: power: reset: qcom-pon: Convert qcom PON binding to yaml
dt-bindings: input: pm8941-pwrkey: Convert pm8941 power key binding to yaml
dt-bindings: power: reset: Change 'additionalProperties' to true
...
The MMS134S like the MMS136 has an event size of 6 bytes.
After this patch, the touchscreen on the Samsung SGH-I407
works fine with PostmarketOS.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210706235951.189289-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
