commit b389286d02 upstream.
For G200_SE_A, PLL M setting is wrong, which leads to blank screen,
or "signal out of range" on VGA display.
previous code had "m |= 0x80" which was changed to
m |= ((pixpllcn & BIT(8)) >> 1);
Tested on G200_SE_A rev 42
This line of code was moved to another file with
commit 877507bb95 ("drm/mgag200: Provide per-device callbacks for
PIXPLLC") but can be easily backported before this commit.
v2: * put BIT(7) First to respect MSB-to-LSB (Thomas)
* Add a comment to explain that this bit must be set (Thomas)
Fixes: 2dd040946e ("drm/mgag200: Store values (not bits) in struct mgag200_pll_values")
Cc: stable@vger.kernel.org
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20221013132810.521945-1-jfalempe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92d43bd3bc ]
ipu_src_rect_width() was introduced to support odd screen resolutions
such as 1366x768 by internally rounding up primary plane width to a
multiple of 8 and compensating with reduced horizontal blanking.
This also caused overlay plane width to be rounded up, which was not
intended. Fix overlay plane width by limiting the rounding up to the
primary plane.
drm_rect_width(&new_state->src) >> 16 is the same value as
drm_rect_width(dst) because there is no plane scaling support.
Fixes: 94dfec48fc ("drm/imx: Add 8 pixel alignment fix")
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20221108141420.176696-1-p.zabel@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20221108141420.176696-1-p.zabel@pengutronix.de
Tested-by: Ian Ray <ian.ray@ge.com>
(cherry picked from commit 4333472f8d)
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b754ed6d1 ]
Having a bigger number of FIFO lines held after vsync is only useful to
SoCs using AFBC to give time to the AFBC decoder to be reset, configured
and enabled again.
For SoCs not using AFBC this, on the contrary, is causing on some
displays issues and a few pixels vertical offset in the displayed image.
Conditionally increase the number of lines held after vsync only for
SoCs using AFBC, leaving the default value for all the others.
Fixes: 24e0d4058e ("drm/meson: hold 32 lines after vsync to give time for AFBC start")
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: added fixes tag]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221216-afbc_s905x-v1-0-033bebf780d9@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4217c6ac81 ]
panfrost_gem_create_with_handle() previously returned a BO but with the
only reference being from the handle, which user space could in theory
guess and release, causing a use-after-free. Additionally if the call to
panfrost_gem_mapping_get() in panfrost_ioctl_create_bo() failed then
a(nother) reference on the BO was dropped.
The _create_with_handle() is a problematic pattern, so ditch it and
instead create the handle in panfrost_ioctl_create_bo(). If the call to
panfrost_gem_mapping_get() fails then this means that user space has
indeed gone behind our back and freed the handle. In which case just
return an error code.
Reported-by: Rob Clark <robdclark@chromium.org>
Fixes: f3ba91228e ("drm/panfrost: Add initial panfrost driver")
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221219140130.410578-1-steven.price@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31d70749bf ]
No need to insert PTEs for the PTE window itself, also foreach expects a
length not an end offset, which could be gigantic here with a second
engine.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211206112539.3149779-3-matthew.auld@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08c7c122ad ]
Ensure we add the engine base only after we calculate the qword offset
into the PTE window.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211206112539.3149779-2-matthew.auld@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8eb7fcce34 ]
The scratch page might not be allocated in LMEM(like on DG2), so instead
of using that as the deciding factor for where the paging structures
live, let's just query the pt before mapping it.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211206112539.3149779-1-matthew.auld@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1d4624cd72 upstream.
Some special polaris 10 chips overlap with the polaris11
DID range. Handle this properly in the driver.
v2: use local flags for other function calls.
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47078311b8 upstream.
A problem about modprobe ingenic-drm failed is triggered with the following
log given:
[ 303.561088] Error: Driver 'ingenic-ipu' is already registered, aborting...
modprobe: ERROR: could not insert 'ingenic_drm': Device or resource busy
The reason is that ingenic_drm_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without unregistering ingenic_ipu_driver_ptr, resulting
the ingenic-drm can never be installed later.
A simple call graph is shown as below:
ingenic_drm_init()
platform_driver_register() # ingenic_ipu_driver_ptr are registered
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without unregister ingenic_ipu_driver_ptr
Fixing this problem by checking the return value of
platform_driver_register() and do platform_unregister_drivers() if
error happened.
Fixes: fc1acf317b ("drm/ingenic: Add support for the IPU")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20221104064512.8569-1-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9cdf41306 upstream.
intel_dsi->ports contains bitmask of enabled ports and correspondingly
logic for selecting port for VBT packet sending must use port specific
bitmask when deciding appropriate port.
Fixes: 08c59dde71 ("drm/i915/dsi: fix VBT send packet port selection for ICL+")
Cc: stable@vger.kernel.org
Signed-off-by: Mikko Kovanen <mikko.kovanen@aavamobile.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/DBBPR09MB466592B16885D99ABBF2393A91119@DBBPR09MB4665.eurprd09.prod.outlook.com
(cherry picked from commit 8d58bb7991)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cf949c7fa upstream.
Invalid userspace dma surface copies could potentially overflow
the memcpy from the surface to the snooped image leading to crashes.
To fix it the dimensions of the copybox have to be validated
against the expected size of the snooped cursor.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Fixes: 2ac863719e ("vmwgfx: Snoop DMA transfers with non-covering sizes")
Cc: <stable@vger.kernel.org> # v3.2+
Reviewed-by: Michael Banack <banackm@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026031936.1004280-1-zack@kde.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fdc2d490e upstream.
A typical DP-MST unplug removes a KMS connector. However care must
be taken to properly synchronize with user-space. The expected
sequence of events is the following:
1. The kernel notices that the DP-MST port is gone.
2. The kernel marks the connector as disconnected, then sends a
uevent to make user-space re-scan the connector list.
3. User-space notices the connector goes from connected to disconnected,
disables it.
4. Kernel handles the IOCTL disabling the connector. On success,
the very last reference to the struct drm_connector is dropped and
drm_connector_cleanup() is called.
5. The connector is removed from the list, and a uevent is sent to tell
user-space that the connector disappeared.
The very last step was missing. As a result, user-space thought the
connector still existed and could try to disable it again. Since the
kernel no longer knows about the connector, that would end up with
EINVAL and confused user-space.
Fix this by sending a hotplug uevent from drm_connector_cleanup().
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: stable@vger.kernel.org
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Jonas Ådahl <jadahl@redhat.com>
Tested-by: Jonas Ådahl <jadahl@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221017153150.60675-2-contact@emersion.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3153eebb7a ]
Bspecs has updated recently to remove the restriction to disable
DDI/Transcoder before setting PHY test pattern. This update is to
address PHY compliance test failures observed on a port with LTTPR.
The issue is that when Transc. is disabled, the main link signals fed
to LTTPR will be dropped invalidating link training, which will affect
the quality of the phy test pattern when the transcoder is enabled again.
v2: Update commit message (Clint)
v3: Add missing Signed-off in v2
v4: Update Bspec and commit message for pre-gen12 (Jani)
Bspec: 50482, 7555
Fixes: 8cdf727119 ("drm/i915/dp: Program vswing, pre-emphasis, test-pattern")
Cc: Imre Deak <imre.deak@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
CC: Jani Nikula <jani.nikula@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221123220926.170034-1-khaled.almahallawy@intel.com
(cherry picked from commit be4a847652)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ad811cc08 ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/gpu/drm/sti/sti_hda.c:637:16: error: incompatible function pointer types initializing 'enum drm_mode_status (*)(struct drm_connector *, struct drm_display_mode *)' with an expression of type 'int (struct drm_connector *, struct drm_display_mode *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.mode_valid = sti_hda_connector_mode_valid,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/sti/sti_dvo.c:376:16: error: incompatible function pointer types initializing 'enum drm_mode_status (*)(struct drm_connector *, struct drm_display_mode *)' with an expression of type 'int (struct drm_connector *, struct drm_display_mode *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.mode_valid = sti_dvo_connector_mode_valid,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/sti/sti_hdmi.c:1035:16: error: incompatible function pointer types initializing 'enum drm_mode_status (*)(struct drm_connector *, struct drm_display_mode *)' with an expression of type 'int (struct drm_connector *, struct drm_display_mode *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.mode_valid = sti_hdmi_connector_mode_valid,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
->mode_valid() in 'struct drm_connector_helper_funcs' expects a return
type of 'enum drm_mode_status', not 'int'. Adjust the return type of
sti_{dvo,hda,hdmi}_connector_mode_valid() to match the prototype's to
resolve the warning and CFI failure.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221102155623.3042869-1-nathan@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96d845a67b ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_rgb.c:74:16: error: incompatible function pointer types initializing 'enum drm_mode_status (*)(struct drm_connector *, struct drm_display_mode *)' with an expression of type 'int (struct drm_connector *, struct drm_display_mode *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.mode_valid = fsl_dcu_drm_connector_mode_valid,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
->mode_valid() in 'struct drm_connector_helper_funcs' expects a return
type of 'enum drm_mode_status', not 'int'. Adjust the return type of
fsl_dcu_drm_connector_mode_valid() to match the prototype's to resolve
the warning and CFI failure.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221102154215.78059-1-nathan@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5842abd985 ]
[WHY]
Corruption can occur in LB if vready_offset is not large enough.
DML calculates vready_offset for each pipe, but we currently select the
top pipe's vready_offset, which is not necessarily enough for all pipes
in the group.
[HOW]
Wherever program_global_sync is currently called, iterate through the
entire pipe group and find the highest vready_offset.
Reviewed-by: Dillon Varone <Dillon.Varone@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fc1ba4aa5 ]
[Why&How]
Firmware headers dictate that gpio_pin array only has a size of 8. The
count returned from vbios however is greater than 8.
Fix this by not using array indexing but incrementing the pointer since
gpio_pin definition in atomfirmware.h is hardcoded to size 8
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 890d637523 ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/gpu/drm/mediatek/mtk_hdmi.c:1407:16: error: incompatible function pointer types initializing 'enum drm_mode_status (*)(struct drm_bridge *, const struct drm_display_info *, const struct drm_display_mode *)' with an expression of type 'int (struct drm_bridge *, const struct drm_display_info *, const struct drm_display_mode *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.mode_valid = mtk_hdmi_bridge_mode_valid,
^~~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
->mode_valid() in 'struct drm_bridge_funcs' expects a return type of
'enum drm_mode_status', not 'int'. Adjust the return type of
mtk_hdmi_bridge_mode_valid() to match the prototype's to resolve the
warning and CFI failure.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 442cf8e22b ]
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Cc: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107192545.9896-8-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bfaa28000 ]
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Link: https://patchwork.freedesktop.org/patch/msgid/20221107192545.9896-7-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2a1c5ca50 ]
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107192545.9896-5-ville.syrjala@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4d0ef7520 ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/gpu/drm/amd/amdgpu/../pm/swsmu/amdgpu_smu.c:3008:29: error: incompatible function pointer types initializing 'int (*)(void *, uint32_t, long *, uint32_t)' (aka 'int (*)(void *, unsigned int, long *, unsigned int)') with an expression of type 'int (void *, enum PP_OD_DPM_TABLE_COMMAND, long *, uint32_t)' (aka 'int (void *, enum PP_OD_DPM_TABLE_COMMAND, long *, unsigned int)') [-Werror,-Wincompatible-function-pointer-types-strict]
.odn_edit_dpm_table = smu_od_edit_dpm_table,
^~~~~~~~~~~~~~~~~~~~~
1 error generated.
There are only two implementations of ->odn_edit_dpm_table() in 'struct
amd_pm_funcs': smu_od_edit_dpm_table() and pp_odn_edit_dpm_table(). One
has a second parameter type of 'enum PP_OD_DPM_TABLE_COMMAND' and the
other uses 'u32'. Ultimately, smu_od_edit_dpm_table() calls
->od_edit_dpm_table() from 'struct pptable_funcs' and
pp_odn_edit_dpm_table() calls ->odn_edit_dpm_table() from 'struct
pp_hwmgr_func', which both have a second parameter type of 'enum
PP_OD_DPM_TABLE_COMMAND'.
Update the type parameter in both the prototype in 'struct amd_pm_funcs'
and pp_odn_edit_dpm_table() to 'enum PP_OD_DPM_TABLE_COMMAND', which
cleans up the warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0d0f10873 ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/gpu/drm/amd/amdgpu/mxgpu_ai.c:412:15: error: incompatible function pointer types initializing 'void (*)(struct amdgpu_device *, u32, u32, u32, u32)' (aka 'void (*)(struct amdgpu_device *, unsigned int, unsigned int, unsigned int, unsigned int)') with an expression of type 'void (struct amdgpu_device *, enum idh_request, u32, u32, u32)' (aka 'void (struct amdgpu_device *, enum idh_request, unsigned int, unsigned int, unsigned int)') [-Werror,-Wincompatible-function-pointer-types-strict]
.trans_msg = xgpu_ai_mailbox_trans_msg,
^~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
drivers/gpu/drm/amd/amdgpu/mxgpu_nv.c:435:15: error: incompatible function pointer types initializing 'void (*)(struct amdgpu_device *, u32, u32, u32, u32)' (aka 'void (*)(struct amdgpu_device *, unsigned int, unsigned int, unsigned int, unsigned int)') with an expression of type 'void (struct amdgpu_device *, enum idh_request, u32, u32, u32)' (aka 'void (struct amdgpu_device *, enum idh_request, unsigned int, unsigned int, unsigned int)') [-Werror,-Wincompatible-function-pointer-types-strict]
.trans_msg = xgpu_nv_mailbox_trans_msg,
^~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
The type of the second parameter in the prototype should be 'enum
idh_request' instead of 'u32'. Update it to clear up the warnings.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6803dfd3a6 ]
This reverts commit 55eea8ef98.
This quirk is now handled in the DRM core, so we can drop all of
the internal code that was added to handle it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d232afb1f3 ]
In dce6(0,1,4)_create_resource_pool and dce80_create_resource_pool
the allocated memory should be released if construct pool fails.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: gehao <gehao@kylinos.cn>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc7d3fb446 ]
The GC300's features register doesn't specify that a 2D pipe is
available, and like the GC600, its idle register reports zero bits where
modules aren't present.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75818afff6 ]
This patch fixes potential memory leakage and seg fault
in _gpuvm_import_dmabuf() function
Fixes: d4ec4bdc0b ("drm/amdkfd: Allow access for mmapping KFD BOs")
Signed-off-by: Konstantin Meskhidze <konstantin.meskhidze@huawei.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca54639c77 ]
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in amdgpu_atrm_get_bios() with 'pdev' not NULL, we
need to call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak.
Fixes: d38ceaf99e ("drm/amdgpu: add core driver (v4)")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 725a521a18 ]
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in radeon_atrm_get_bios() with 'pdev' not NULL, we
need to call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak.
Fixes: d8ade3526b ("drm/radeon: handle non-VGA class pci devices with ATRM")
Fixes: c61e277587 ("drm/radeon: split ATRM support out from the ATPX handler (v3)")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dca7efe6e ]
Return true early if ASIC is in BACO state already, no need
to talk to SMU. It can fix the issue that driver was not
calling BACO exit at all in runtime pm resume, and a timing
issue leading to a PCI AER error happened eventually.
Fixes: 8795e182b0 ("PCI/portdrv: Don't disable AER reporting in get_port_device_capability()")
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ad4384d53 ]
Add the missing clk_disable_unprepare() before return from
tegra_dc_probe() in the error handling path.
Fixes: f68ba6912b ("drm/tegra: dc: Link DC1 to DC0 on Tegra20")
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b85e285e3d ]
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
So before returning from amdgpu_device_resume|suspend_display_audio(),
pci_dev_put() is called to avoid refcount leak.
Fixes: 3f12acc8d6 ("drm/amdgpu: put the audio codec into suspend state before gpu reset V3")
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6d1918794 ]
If we get an error (other than -ENOENT) we need to propagate that up the
stack. Otherwise if the nvmem driver hasn't probed yet, we'll end up
end up claiming that we support all the OPPs which is not likely to be
true (and on some generations impossible to be true, ie. if there are
conflicting OPPs).
v2: Update commit msg, gc unused label, etc
v3: Add previously missing \n's
Fixes: fe7952c629 ("drm/msm: Add speed-bin support to a618 gpu")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/511690/
Link: https://lore.kernel.org/r/20221115154637.1613968-1-robdclark@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b230555f32 ]
These formats are not subsampled, but that means hsub and vsub should be
1, not 0.
Fixes: 94b292b277 ("drm: drm_fourcc: add NV15, Q410, Q401 YUV formats")
Reported-by: George Kennedy <george.kennedy@oracle.com>
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913144306.17279-1-brian.starkey@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 006ea1b582 ]
Adds a format that is 3 10bit YUV 4:2:0 samples packed into
a 32bit word (with 2 spare bits).
Supported on Broadcom BCM2711 chips.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20211215091739.135042-2-maxime@cerno.tech
Stable-dep-of: b230555f32 ("drm/fourcc: Fix vsub/hsub for Q410 and Q401")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d27252b570 ]
In the PP_OD_EDIT_VDDC_CURVE case the "input_index" variable is capped at
2 but not checked for negative values so it results in an out of bounds
read. This value comes from the user via sysfs.
Fixes: d5bf265394 ("drm/amd/powerplay: added vega20 overdrive support V3")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff446c0f62 ]
Modify dpi power on/off sequence so that the first gpio operation will
take effect.
Fixes: 6bd4763fd5 ("drm/mediatek: set dpi pin mode to gpio low to avoid leakage current")
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10276a20be ]
When the radeon driver reads the bios information from ACPI
table in radeon_acpi_vfct_bios(), it misses to call acpi_put_table()
to release the ACPI memory after the init, so add acpi_put_table()
properly to fix the memory leak.
v2: fix text formatting (Alex)
Fixes: 268ba0a99f ("drm/radeon: implement ACPI VFCT vbios fetch (v3)")
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b964444b2b ]
Use devm_pm_runtime_enable() to enable runtime PM. This way its effect
will be reverted on device unbind/destruction.
Fixes: 6ed9ed484d ("drm/msm/hdmi: Set up runtime PM for HDMI")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/499647/
Link: https://lore.kernel.org/r/20220826093927.851597-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68e674b13b ]
The HDMI driver has code to configure extra GPIOs, which predates
pinctrl support. Nowadays all platforms should use pinctrl instead.
Neither of upstreamed Qualcomm platforms uses these properties, so it's
safe to drop them.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/488858/
Link: https://lore.kernel.org/r/20220609122350.3157529-7-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Stable-dep-of: b964444b2b ("drm/msm/hdmi: use devres helper for runtime PM management")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dba27f1a1 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
We fix it by replacing it with the newest pm_runtime_resume_and_get
to keep usage counter balanced.
Fixes: 34cc0aa254 ("drm/rockchip: Add support for Rockchip Soc LVDS")
Fixes: cca1705c3d ("drm/rockchip: lvds: Add PX30 support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922132107.105419-3-zhangqilong3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f8033d566 ]
Commit 902bc65de0 ("drm/amdgpu/powerplay/psm: return an error in power
state init") made the power state init function return early in case of
failure to get an entry from the powerplay table, but it missed to clean up
the allocated memory for the current power state before returning.
Fixes: 902bc65de0 ("drm/amdgpu/powerplay/psm: return an error in power state init")
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a0cdcd664 ]
adv7533 bridge tries to dynamically switch lanes based on the
mode by detaching and attaching the mipi dsi device.
This approach is incorrect because this method of dynamic switch of
detaching and attaching the mipi dsi device also results in removing
and adding the component which is not necessary.
This approach is also prone to deadlocks. So for example, on the
db410c whenever this path is executed with lockdep enabled,
this results in a deadlock due to below ordering of locks.
-> #1 (crtc_ww_class_acquire){+.+.}-{0:0}:
lock_acquire+0x6c/0x90
drm_modeset_acquire_init+0xf4/0x150
drmm_mode_config_init+0x220/0x770
msm_drm_bind+0x13c/0x654
try_to_bring_up_aggregate_device+0x164/0x1d0
__component_add+0xa8/0x174
component_add+0x18/0x2c
dsi_dev_attach+0x24/0x30
dsi_host_attach+0x98/0x14c
devm_mipi_dsi_attach+0x38/0xb0
adv7533_attach_dsi+0x8c/0x110
adv7511_probe+0x5a0/0x930
i2c_device_probe+0x30c/0x350
really_probe.part.0+0x9c/0x2b0
__driver_probe_device+0x98/0x144
driver_probe_device+0xac/0x14c
__device_attach_driver+0xbc/0x124
bus_for_each_drv+0x78/0xd0
__device_attach+0xa8/0x1c0
device_initial_probe+0x18/0x24
bus_probe_device+0xa0/0xac
deferred_probe_work_func+0x90/0xd0
process_one_work+0x28c/0x6b0
worker_thread+0x240/0x444
kthread+0x110/0x114
ret_from_fork+0x10/0x20
-> #0 (component_mutex){+.+.}-{3:3}:
__lock_acquire+0x1280/0x20ac
lock_acquire.part.0+0xe0/0x230
lock_acquire+0x6c/0x90
__mutex_lock+0x84/0x400
mutex_lock_nested+0x3c/0x70
component_del+0x34/0x170
dsi_dev_detach+0x24/0x30
dsi_host_detach+0x20/0x64
mipi_dsi_detach+0x2c/0x40
adv7533_mode_set+0x64/0x90
adv7511_bridge_mode_set+0x210/0x214
drm_bridge_chain_mode_set+0x5c/0x84
crtc_set_mode+0x18c/0x1dc
drm_atomic_helper_commit_modeset_disables+0x40/0x50
msm_atomic_commit_tail+0x1d0/0x6e0
commit_tail+0xa4/0x180
drm_atomic_helper_commit+0x178/0x3b0
drm_atomic_commit+0xa4/0xe0
drm_client_modeset_commit_atomic+0x228/0x284
drm_client_modeset_commit_locked+0x64/0x1d0
drm_client_modeset_commit+0x34/0x60
drm_fb_helper_lastclose+0x74/0xcc
drm_lastclose+0x3c/0x80
drm_release+0xfc/0x114
__fput+0x70/0x224
____fput+0x14/0x20
task_work_run+0x88/0x1a0
do_exit+0x350/0xa50
do_group_exit+0x38/0xa4
__wake_up_parent+0x0/0x34
invoke_syscall+0x48/0x114
el0_svc_common.constprop.0+0x60/0x11c
do_el0_svc+0x30/0xc0
el0_svc+0x58/0x100
el0t_64_sync_handler+0x1b0/0x1bc
el0t_64_sync+0x18c/0x190
Due to above reasons, remove the dynamic lane switching
code from adv7533 bridge chip and filter out the modes
which would need different number of lanes as compared
to the initialization time using the mode_valid callback.
This can be potentially re-introduced by using the pre_enable()
callback but this needs to be evaluated first whether such an
approach will work so this will be done with a separate change.
changes since RFC:
- Fix commit text and add TODO comment
changes in v2:
- Fix checkpatch formatting errors
Fixes: 62b2f026cd ("drm/bridge: adv7533: Change number of DSI lanes dynamically")
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/16
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://lore.kernel.org/r/1661797363-7564-1-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1665522649-3423-1-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3d6b1bf85 ]
Cheap monitors sometimes advertise YUV modes they don't really have
(HDMI specification mandates YUV support so even monitors without actual
support will often wrongfully advertise it) which results in YUV matches
and user forum complaints of a red tint to light colour display areas in
common desktop environments.
Moving the default RGB fall-back before YUV selection results in RGB
mode matching in most cases, reducing complaints.
Fixes: 6c3c719936 ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Guillaume BRUN <the.cheaterman@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221116143523.2126-1-the.cheaterman@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
