[ Upstream commit e43212e0f5 ]
Configure ip-polling register to enable polling for all voltage monitor
channels.
This enables reading the voltage values for all inputs other than just
input 0.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-7-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91a9e063cd ]
Fix voltage allocation and reading to support all channels in all VMs.
Prior to this change allocation and reading were done only for the first
channel in each VM.
This change counts the total number of channels for allocation, and takes
into account the channel offset when reading the sample data register.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-6-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 227a3a2fc3 ]
According to Moortec Embedded Voltage Monitor (MEVM) series 3 data
sheet, the minimum input signal is -100mv and maximum input signal
is +1000mv.
The equation used to convert the digital word to voltage uses mixed
types (*val signed and n unsigned), and on 64 bit machines also has
different size, since sizeof(u32) = 4 and sizeof(long) = 8.
So when measuring a negative input, n will be small enough, such that
PVT_N_CONST * n < PVT_R_CONST, and the result of
(PVT_N_CONST * n - PVT_R_CONST) will overflow to a very big positive
32 bit number. Then when storing the result in *val it will be the same
value just in 64 bit (instead of it representing a negative number which
will what happen when sizeof(long) = 4).
When -1023 <= (PVT_N_CONST * n - PVT_R_CONST) <= -1
dividing the number by 1024 should result of in 0, but because ">> 10"
is used, and the sign bit is used to fill the vacated bit positions, it
results in -1 (0xf...fffff) which is wrong.
This change fixes the sign problem and supports negative values by
casting n to long and replacing the shift right with div operation.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-5-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb9195bd66 ]
This issue is relevant when "intel,vm-map" is set in device-tree, and
defines a lower number of VMs than actually supported.
This change is needed for all places that use pvt->v_num or vm_num
later on in the code.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-4-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81114fc3d2 ]
Bug - in case "intel,vm-map" is missing in device-tree ,'num' is set
to 0, and no voltage channel infos are allocated.
The reason num is set to 0 when "intel,vm-map" is missing is to set the
entire pvt->vm_idx[] with incremental channel numbers, but it didn't
take into consideration that same num is used later in devm_kcalloc().
If "intel,vm-map" does exist there is no need to set the unspecified
channels with incremental numbers, because the unspecified channels
can't be accessed in pvt_read_in() which is the only other place besides
the probe functions that uses pvt->vm_idx[].
This change fixes the bug by moving the incremental channel numbers
setting to be done only if "intel,vm-map" property is defined (starting
loop from 0), and removing 'num = 0'.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-3-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1f05f65bdd upstream.
The tps23861 registers are little-endian, and regmap_read_bulk() does
not do byte order conversion. On BE machines, the bytes were swapped,
and the interpretation of the resistance value was incorrect.
To make it work on both big and little-endian machines, use
le16_to_cpu() to convert the resitance register to host byte order.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Fixes: fff7b8ab22 ("hwmon: add Texas Instruments TPS23861 driver")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220905142806.110598-1-mr.nuke.me@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5918036cfa ]
Adding a MODULE_ALIAS() to drivetemp will make the driver easier
for modprobe to autoprobe.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220712214624.1845158-1-linus.walleij@linaro.org
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd2d53c367 ]
Some devices like the Fujitsu Celsius W380 do contain
a working sch56xx hardware monitoring device, but do
not contain the necessary DMI onboard device.
Do not check for the presence of an suitable onboard device
on these machines. The list of affected machines was created
using data collected by the Linux Hardware Project.
Tested on a Fujitsu Esprimo P720, but sadly not on a affected
machine.
Fixes: 393935baa4 (hwmon: (sch56xx-common) Add automatic module loading on supported devices)
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220604220200.2567-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d4edccc9b ]
Taking a lock at the beginning of .remove() doesn't prevent new readers.
With the existing approach it can happen, that a read occurs just when
the lock was taken blocking the reader until the lock is released at the
end of the remove callback which then accessed *data that is already
freed then.
To actually fix this problem the hwmon core needs some adaption. Until
this is implemented take the optimistic approach of assuming that all
readers are gone after hwmon_device_unregister() and
sysfs_remove_group() as most other drivers do. (And once the core
implements that, taking the lock would deadlock.)
So drop the lock, move the reset to after device unregistration to keep
the device in a workable state until it's deregistered. Also add a error
message in case the reset fails and return 0 anyhow. (Returning an error
code, doesn't stop the platform device unregistration and only results
in a little helpful error message before the devm cleanup handlers are
called.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220725194344.150098-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 385e5f5705 ]
A user reported that the program dell-bios-fan-control
worked on his Dell XPS 13 7390 to switch off automatic
fan control.
Since it uses the same mechanism as the dell_smm_hwmon
module, add this model to the fan control whitelist.
Compile-tested only.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220612041806.11367-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f4e6960f4f upstream.
Commit c3963bc0a0 ("hwmon: (nct6775) Split core and platform
driver") introduced a slight change in nct6775_suspend() in order to
avoid an otherwise-needless symbol export for nct6775_update_device(),
replacing a call to that function with a simple dev_get_drvdata()
instead.
As it turns out, there is no guarantee that nct6775_update_device()
is ever called prior to suspend. If this happens, the resume function
ends up writing bad data into the various chip registers, which results
in a crash shortly after resume.
To fix the problem, just add the symbol export and return to using
nct6775_update_device() as was employed previously.
Reported-by: Zoltán Kővágó <dirty.ice.hu@gmail.com>
Tested-by: Zoltán Kővágó <dirty.ice.hu@gmail.com>
Fixes: c3963bc0a0 ("hwmon: (nct6775) Split core and platform driver")
Cc: stable@kernel.org
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220810052646.13825-1-zev@bewilderbeest.net
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If platform_device_add() fails, it no need to call platform_device_del(), split
platform_device_unregister() into platform_device_del/put(), so platform_device_put()
can be called separately.
Fixes: 8808a793f0 ("ibmaem: new driver for power/energy/temp meters in IBM System X hardware")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220701074153.4021556-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Drop the redundant word 'the' in the comments following
/*
* Set PHASE registers on all pages to 0xff to ensure that phase
* specific commands will apply to all phases of a given page (rail).
* This only affects the READ_IOUT and READ_TEMPERATURE2 registers.
* READ_IOUT will return the sum of currents of all phases of a rail,
* and READ_TEMPERATURE2 will return the maximum temperature detected
* for the [the - DROP] phases of the rail.
*/
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Link: https://lore.kernel.org/r/20220622063231.20612-1-jiangjian@cdjrlc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently, the response to the power cap command overwrites the
first eight bytes of the poll response, since the commands use
the same buffer. This means that user's get the wrong data between
the time of sending the power cap and the next poll response update.
Fix this by specifying a different buffer for the power cap command
response.
Fixes: 5b5513b880 ("hwmon: Add On-Chip Controller (OCC) hwmon driver")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628203029.51747-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This fixes a regression where coma lead to concatenating board names
and broke module loading for C8H.
Fixes: 5b4285c57b ("hwmon: (asus-ec-sensors) fix Formula VIII definition")
Signed-off-by: Michael Carns <mike@carns.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220615122544.140340-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unbinding the driver or removing the parent device at the same time
as using the OCC active sysfs file can cause the driver to unregister
the hwmon device twice. Prevent this by locking the occ mutex in the
shutdown function.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220606185455.21126-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If no memory can be allocated, some resources still need to be released as
already done in the other error handling paths.
Fixes: 752b927951 ("hwmon: (aquacomputer_d5next) Add support for Aquacomputer Octo")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/be6b955d50de140fcc96bd116150b435021bf567.1653225250.git.christophe.jaillet@wanadoo.fr
Reviewed-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make sure that the support of PEC is determined before the read of other
registers. Otherwise the validation of PEC can trigger an error on the read
of STATUS_BYTE or STATUS_WORD registers.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without the move of the code, at the second load of
the driver (or bind) the STATUS_BYTE or STATUS_WORD register is always
read with PEC enabled, which is likely to cause a read error resulting
with fail of a driver load (or bind).
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220519233334.438621-1-dev_public@wujek.eu
Fixes: 75d2b2b06b ("hwmon: (pmbus) disable PEC if not enabled")
Fixes: 4e5418f787 ("hwmon: (pmbus_core) Check adapter PEC support")
[groeck: Added Fixes: tags, dropped continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Building arm:allmodconfig may fail with the following error.
In function 'fortify_memcpy_chk',
inlined from 'bitmap_copy' at include/linux/bitmap.h:261:2,
inlined from 'bitmap_copy_clear_tail' at include/linux/bitmap.h:270:2,
inlined from 'bitmap_from_u64' at include/linux/bitmap.h:622:2,
inlined from 'check_populated_dimms' at
drivers/hwmon/peci/dimmtemp.c:284:2:
include/linux/fortify-string.h:344:25: error:
call to '__write_overflow_field' declared with attribute warning:
detected write beyond size of field (1st parameter)
The problematic code is
bitmap_from_u64(priv->dimm_mask, dimm_mask);
dimm_mask is declared as u64, but the bitmap in priv->dimm_mask is only
24 bit wide. On 32-bit systems, this results in writes over the end of
the bitmap.
Fix the problem by using u32 instead of u64 for dimm_mask. This is
currently sufficient, and a compile time check to ensure that the number
of dimms does not exceed the bit map size is already in place.
Fixes: 73bc1b885d ("hwmon: peci: Add dimmtemp driver")
Cc: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some lm90 compatible devices can operate in an extended temperature mode.
This feature is now enabled if the property is set in the corresponding
device tree node.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220517135614.8185-2-holger.brunck@hitachienergy.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ida_alloc()/ida_free() instead of deprecated
ida_simple_get()/ida_simple_remove() .
Signed-off-by: keliu <liuke94@huawei.com>
Link: https://lore.kernel.org/r/20220517063126.2142637-2-liuke94@huawei.com
[groeck: Updated subject to include driver name]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Cc: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Cc: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Various attempts were made recently to "convert" the old
hwmon_device_register() API to devm_hwmon_device_register_with_info()
by just changing the function name without actually converting the
driver. Prevent this from happening by making the 'chip' parameter of
devm_hwmon_device_register_with_info() mandatory.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal subsystem registers a hwmon driver without providing
chip or sysfs group information. This is for legacy reasons and
would be difficult to change. At the same time, we want to enforce
that chip information is provided when registering a hwmon device
using hwmon_device_register_with_info(). To enable this, introduce
a special API for use only by the thermal subsystem.
Acked-by: Rafael J . Wysocki <rafael@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adds support for the ROG STRIX X570-E GAMING WIFI II board and
simplifies formatting for the list of supported models.
Signed-off-by: Debabrata Banerjee <dbavatar@gmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220505073351.123753-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver provides an i2c I/O mechanism for the core nct6775 driver,
as might be used by a BMC. Because the Super I/O chip is shared with
the host CPU in such a scenario (and the host should ultimately be in
control of it), the i2c driver is strictly read-only to avoid
interfering with any usage by the host (aside from the bank-select
register, which seems to be replicated for the i2c interface).
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Renze Nicolai <renze@rnplus.nl>
Link: https://lore.kernel.org/r/20220428012707.24921-3-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Boards such as
* PRO H410T
* PRIME H410M-R
* ROG STRIX X570-E GAMING WIFI II
have got a nct6775 chip, but by default there's no use of it
because of resource conflict with WMI method.
This commit adds such boards to the WMI monitoring list.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Reported-by: renedis <renedis@hotmail.com>
Reported-by: Dmitrii Levchenko <e_dimas@rambler.ru>
Reported-by: Hubert Banas <hubert.banas@gmail.com>
Link: https://lore.kernel.org/r/20220507072933.3013-1-pauk.denis@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some include directives are no longer necessary due to previous driver
changes. Remove them now to further improve driver code clarity.
Mutex usage has ceased since commit 719af4f1a4 ("hwmon: (lm83) Use
regmap").
Ever since commit a0ac840d99 ("hwmon: (lm83) Convert to use
devm_hwmon_device_register_with_groups") functions sysfs_create_group
and sysfs_remove_group are no longer used by the driver.
Signed-off-by: Karl Mehltretter <kmehltretter@gmail.com>
Link: https://lore.kernel.org/r/20220508144601.22796-1-kmehltretter@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pmbus core does not have operations for getting or setting voltage.
Add functions get/set voltage for the dynamic regulator framework.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220503104631.3515715-5-marten.lindahl@axis.com
[groeck: cosmetic alignment / empty line fixes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some pmbus device drivers have device tree support and
may want to use of-thermal to register a thermal zone
OF sensor for those device drivers.
This way we allow describing device tree thermal zones
for pmbus device drivers with device tree support.
This patch achieves this by registering pmbus sensors
with thermal subsystem if they are PSC_TEMPERATURE
and are providing _input hwmon interface.
Cc: Guenter Roeck <linux@roeck-us.net> (maintainer:PMBUS HARDWARE MONITORING DRIVERS)
Cc: Jean Delvare <jdelvare@suse.com> (maintainer:HARDWARE MONITORING)
Cc: linux-hwmon@vger.kernel.org (open list:PMBUS HARDWARE MONITORING DRIVERS)
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Eduardo Valentin <evalenti@kernel.org>
Link: https://lore.kernel.org/r/20220428174926.2150-1-eduval@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make use of enum chips and use a switch statement in load_attenuators()
so that the compiler can tell us if we've failed to cater for a
supported chip.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220323034056.260455-4-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7473, adt7475, adt7476 and adt7490 have pins that can be used for
different functions. On the adt7473 and adt7475 this is pins 5 and 9.
On the adt7476 and adt7490 this is pins 10 and 14.
The first pin can either be PWM2(default) or SMBALERT#. The second pin
can be TACH4(default), THERM#, SMBALERT# or GPIO.
The adt7475 driver has always been able to detect the configuration if
it had been done by an earlier boot stage. Add support for configuring
the pins based on the hardware description in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220323034056.260455-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the temperatur sensor and the fan controller on the
Microchip LAN966x SoC. Apparently, an Analog Bits PVT sensor is used
which can measure temperature and process voltages. But only a forumlae
for the temperature sensor is known. Additionally, the SoC support a fan
tacho input as well as a PWM signal to control the fan.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-5-michael@walle.cc
[groeck: Added missing reference in Documentation/hwmon/index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The polynomial calculation function was moved into lib/ to be able to
reuse it. Move over to this one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-3-michael@walle.cc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
