[ Upstream commit 76950f7162 ]
To perform the reserve_crashkernel() operation kexec uses SECTION_SIZE to
find a memblock in a range.
SECTION_SIZE is not defined for nommu systems. Trying to compile kexec in
these conditions results in a build error:
linux/arch/arm/kernel/setup.c: In function ‘reserve_crashkernel’:
linux/arch/arm/kernel/setup.c:1016:25: error: ‘SECTION_SIZE’ undeclared
(first use in this function); did you mean ‘SECTIONS_WIDTH’?
crash_size, SECTION_SIZE);
^~~~~~~~~~~~
SECTIONS_WIDTH
linux/arch/arm/kernel/setup.c:1016:25: note: each undeclared identifier
is reported only once for each function it appears in
linux/scripts/Makefile.build:265: recipe for target 'arch/arm/kernel/setup.o'
failed
Make KEXEC depend on MMU to fix the compilation issue.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8239fc7755 ]
Commit e17b1af96b
"ARM: 8857/1: efi: enable CP15 DMB instructions before cleaning the cache"
added some explicit handling of the CP15BEN bit in the SCTLR system
register, to ensure that CP15 barrier instructions are enabled, even
if we enter the decompressor via the EFI stub.
However, as it turns out, there are other ways in which we may end up
using CP15 barrier instructions without them being enabled. I.e., when
the decompressor startup code skips the cache_on() initially, we end
up calling cache_clean_flush() with the caches and MMU off, in which
case the CP15BEN bit in SCTLR may not be programmed either. And in
fact, cache_on() itself issues CP15 barrier instructions before actually
enabling them by programming the new SCTLR value (and issuing an ISB)
Since these routines are shared between v7 CPUs and older ones that
implement the CPUID extension as well, using the ordinary v7 barrier
instructions in this code is not possible, and so we should enable the
CP15 ones explicitly before issuing them. Note that a v7 ISB is still
required between programming the SCTLR register and using the CP15 barrier
instructions, and we should take care to branch over it if the CP15BEN
bit is already set, given that in that case, the CPU may not support it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf206bca17 ]
An experimental test with the command below gives this error:
rk3188-bqedison2qc.dt.yaml: dwmmc@10218000: wifi@1:
'reg' is a required property
So fix this by adding a reg property to the brcmf sub node.
Also add #address-cells and #size-cells to prevent more warnings.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110134420.11280-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ff15a86d0 ]
Add a fixed regulator and use it as power supply for DSI panel.
Fixes: 18c8866266 ("ARM: dts: stm32: Add display support on stm32f469-disco")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8443ffd1bb ]
Add a device node for the global timer, which is part of the Cortex-A9
MPCore.
The global timer can serve as an accurate (4 ns) clock source for
scheduling and delay loops.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191211135222.26770-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bb1e09c4c ]
Cabling used to connect devices to USBH1 on RDU2 does not meet USB
spec cable quality and cable length requirements to operate at High
Speed, so limit the port to Full Speed only.
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd58a174e5 ]
RDU2 production units come with resistor connecting WP pin to
correpsonding GPIO DNPed for both SD card slots. Drop any WP related
configuration and mark both slots with "disable-wp".
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f9e2df2e6 ]
Few options KALLSYMS_ALL, SCSI, PM_DEVFREQ and mutex/spinlock debugging
were removed with savedefconfig because they were selected by other
options. However these are user-visible options and they might not be
selected in the future. Exactly this happened with commit 0e4a459f56
("tracing: Remove unnecessary DEBUG_FS dependency") removing the
dependency between DEBUG_FS and TRACING.
To avoid losing these options in the future, explicitly mention them in
defconfig.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0388a11074 ]
Add the Performance Monitoring Unit (PMU) device tree node to the H3
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on an OrangePi Zero.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc420c6cee ]
Kmemleak relies on specific symbols to register the read only data
during init (e.g. __start_ro_after_init).
Trying to build an XIP kernel on arm results in the linking error
reported below because when this option is selected read only data
after init are not allowed since .data is read only (.rodata).
arm-linux-gnueabihf-ld: mm/kmemleak.o: in function `kmemleak_init':
kmemleak.c:(.init.text+0x148): undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x14c):
undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x150):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x156):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x162):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x16a):
undefined reference to `__start_ro_after_init'
linux/Makefile:1078: recipe for target 'vmlinux' failed
Fix the issue enabling kmemleak only on non XIP kernels.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e383e871ab upstream.
The CONFIG_ARCH_REQUIRE_GPIOLIB is gone since commit 65053e1a77
("gpio: delete ARCH_[WANTS_OPTIONAL|REQUIRE]_GPIOLIB") and all platforms
should explicitly select GPIOLIB to have it.
Link: https://lore.kernel.org/r/20200130195525.4525-1-krzk@kernel.org
Cc: <stable@vger.kernel.org>
Fixes: 65053e1a77 ("gpio: delete ARCH_[WANTS_OPTIONAL|REQUIRE]_GPIOLIB")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bc81767c5 upstream.
When the ARM accelerated ChaCha driver is built as part of a configuration
that has kernel mode NEON disabled, we expect the compiler to propagate
the build time constant expression IS_ENABLED(CONFIG_KERNEL_MODE_NEON) in
a way that eliminates all the cross-object references to the actual NEON
routines, which allows the chacha-neon-core.o object to be omitted from
the build entirely.
Unfortunately, this fails to work as expected in some cases, and we may
end up with a build error such as
chacha-glue.c:(.text+0xc0): undefined reference to `chacha_4block_xor_neon'
caused by the fact that chacha_doneon() has not been eliminated from the
object code, even though it will never be called in practice.
Let's fix this by adding some IS_ENABLED(CONFIG_KERNEL_MODE_NEON) tests
that are not strictly needed from a logical point of view, but should
help the compiler infer that the NEON code paths are unreachable in
those cases.
Fixes: b36d8c09e7 ("crypto: arm/chacha - remove dependency on generic ...")
Reported-by: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31f3010e60 upstream.
As of commit ac7c3e4ff4 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly"), free_memmap() might not always be inlined, and thus is
triggering a section warning:
WARNING: vmlinux.o(.text.unlikely+0x904): Section mismatch in reference from the function free_memmap() to the function .meminit.text:memblock_free()
Mark it as __init, since the faller (free_unused_memmap) already is.
Fixes: ac7c3e4ff4 ("compiler: enable CONFIG_OPTIMIZE_INLINING forcibly")
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b9dfd986a upstream.
SAM9X60 PMC's has a different PMC. It was not integrated at the moment
commit 01c7031cfa ("ARM: at91: pm: initial PM support for SAM9X60")
was published.
Fixes: 01c7031cfa ("ARM: at91: pm: initial PM support for SAM9X60")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1576062248-18514-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7e0f3fc01 upstream.
The clock rate range for the TCB1 clock is missing. define it in the device
tree.
Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b79 ("ARM: at91/dt: define sama5d3 clocks")
Link: https://lore.kernel.org/r/20200110172007.1253659-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee0aa926dd upstream.
Currently the maximum rate for peripheral clock is calculated based on a
typical 133MHz MCK. The maximum frequency is defined in the datasheet as a
ratio to MCK. Some sama5d3 platforms are using a 166MHz MCK. Update the
device trees to match the maximum rate based on 166MHz.
Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b79 ("ARM: at91/dt: define sama5d3 clocks")
Link: https://lore.kernel.org/r/20200110172007.1253659-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3dd3315ab upstream.
The clock setup on Meson8 cannot achieve a Mali frequency of exactly
182.15MHz. The vendor driver uses "FCLK_DIV7 / 1" for this frequency,
which translates to 2550MHz / 7 / 1 = 364285714Hz.
Update the GPU operating point to that specific frequency to not confuse
myself when comparing the frequency from the .dts with the actual clock
rate on the system.
Fixes: c3ea80b613 ("ARM: dts: meson8b: add the Mali-450 MP2 GPU")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe634a7a9a upstream.
The clock setup on Meson8 cannot achieve a Mali frequency of exactly
182.15MHz. The vendor driver uses "FCLK_DIV7 / 2" for this frequency,
which translates to 2550MHz / 7 / 2 = 182142857Hz.
Update the GPU operating point to that specific frequency to not confuse
myself when comparing the frequency from the .dts with the actual clock
rate on the system.
Fixes: 7d3f6b536e ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01053dadb7 upstream.
clkout1 clock node and its generation tree was missing. Add this based
on the data on TRM and PRCM functional spec.
commit 664ae1ab25 ("ARM: dts: am43xx: add clkctrl nodes") effectively
reverted this commit 8010f13a40 ("ARM: dts: am43xx: add support for
clkout1 clock") which is needed for the ov2659 camera sensor clock
definition hence it is being re-applied here.
Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "clkout1-*ck" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.
Fixes: 664ae1ab25 ("ARM: dts: am43xx: add clkctrl nodes")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d39d86cd4 upstream.
Pull-ups for SAM9 UART/USART TX lines were disabled in a previous
commit. However, several chips in the SAM9 family require pull-ups to
prevent the TX lines from falling (and causing an endless break
condition) when the transceiver is disabled.
From the SAM9G20 datasheet, 32.5.1: "To prevent the TXD line from
falling when the USART is disabled, the use of an internal pull up
is mandatory.". This commit reenables the pull-ups for all chips having
that sentence in their datasheets.
Fixes: 5e04822f7d ("ARM: dts: at91: fixes uart pinctrl, set pullup on rx, clear pullup on tx")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Cc: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20191203142147.875227-1-inguin@gmx.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3388d506 upstream.
For a little over a year, U-Boot has configured the flow controller to
perform automatic RAM re-repair on off->on power transitions of the CPU
rail[1]. This is mandatory for correct operation of Tegra124. However,
RAM re-repair relies on certain clocks, which the kernel must enable and
leave running. PLLP is one of those clocks. This clock is shut down
during LP1 in order to save power. Enable bypass (which I believe routes
osc_div_clk, essentially the crystal clock, to the PLL output) so that
this clock signal toggles even though the PLL is not active. This is
required so that LP1 power mode (system suspend) operates correctly.
The bypass configuration must then be undone when resuming from LP1, so
that all peripheral clocks run at the expected rate. Without this, many
peripherals won't work correctly; for example, the UART baud rate would
be incorrect.
NVIDIA's downstream kernel code only does this if not compiled for
Tegra30, so the added code is made conditional upon the chip ID.
NVIDIA's downstream code makes this change conditional upon the active
CPU cluster. The upstream kernel currently doesn't support cluster
switching, so this patch doesn't test the active CPU cluster ID.
[1] 3cc7942a4ae5 ARM: tegra: implement RAM repair
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3cc4e1d44 upstream.
max_pfn, as set in arch/arm/mm/init.c:
static void __init find_limits(unsigned long *min,
unsigned long *max_low,
unsigned long *max_high)
{
*max_low = PFN_DOWN(memblock_get_current_limit());
*min = PFN_UP(memblock_start_of_DRAM());
*max_high = PFN_DOWN(memblock_end_of_DRAM());
}
with memblock_end_of_DRAM() pointing to the next byte after DRAM. As
such, max_pfn points to the PFN after the end of DRAM.
Thus when using max_pfn to check DMA masks, we should subtract one when
checking DMA ranges against it.
Commit 8bf1268f48 ("ARM: dma-api: fix off-by-one error in
__dma_supported()") fixed the same issue, but missed this spot.
This issue was found while working on the sun4i-csi v4l2 driver on the
Allwinner R40 SoC. On Allwinner SoCs, DRAM is offset at 0x40000000, and
we are starting to use of_dma_configure() with the "dma-ranges" property
in the device tree to have the DMA API handle the offset.
In this particular instance, dma-ranges was set to the same range as the
actual available (2 GiB) DRAM. The following error appeared when the
driver attempted to allocate a buffer:
sun4i-csi 1c09000.csi: Coherent DMA mask 0x7fffffff (pfn 0x40000-0xc0000)
covers a smaller range of system memory than the DMA zone pfn 0x0-0xc0001
sun4i-csi 1c09000.csi: dma_alloc_coherent of size 307200 failed
Fixing the off-by-one error makes things work.
Link: http://lkml.kernel.org/r/20191224030239.5656-1-wens@kernel.org
Fixes: 11a5aa3256 ("ARM: dma-mapping: check DMA mask against available memory")
Fixes: 9f28cde0bc ("ARM: another fix for the DMA mapping checks")
Fixes: ab746573c4 ("ARM: dma-mapping: allow larger DMA mask than supported")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6ae256afd upstream.
On AArch64 you can do a sign-extended load to either a 32-bit or 64-bit
register, and we should only sign extend the register up to the width of
the register as specified in the operation (by using the 32-bit Wn or
64-bit Xn register specifier).
As it turns out, the architecture provides this decoding information in
the SF ("Sixty-Four" -- how cute...) bit.
Let's take advantage of this with the usual 32-bit/64-bit header file
dance and do the right thing on AArch64 hosts.
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191212195055.5541-1-christoffer.dall@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cfbb484de upstream.
Confusingly, there are three SPSR layouts that a kernel may need to deal
with:
(1) An AArch64 SPSR_ELx view of an AArch64 pstate
(2) An AArch64 SPSR_ELx view of an AArch32 pstate
(3) An AArch32 SPSR_* view of an AArch32 pstate
When the KVM AArch32 support code deals with SPSR_{EL2,HYP}, it's either
dealing with #2 or #3 consistently. On arm64 the PSR_AA32_* definitions
match the AArch64 SPSR_ELx view, and on arm the PSR_AA32_* definitions
match the AArch32 SPSR_* view.
However, when we inject an exception into an AArch32 guest, we have to
synthesize the AArch32 SPSR_* that the guest will see. Thus, an AArch64
host needs to synthesize layout #3 from layout #2.
This patch adds a new host_spsr_to_spsr32() helper for this, and makes
use of it in the KVM AArch32 support code. For arm64 we need to shuffle
the DIT bit around, and remove the SS bit, while for arm we can use the
value as-is.
I've open-coded the bit manipulation for now to avoid having to rework
the existing PSR_* definitions into PSR64_AA32_* and PSR32_AA32_*
definitions. I hope to perform a more thorough refactoring in future so
that we can handle pstate view manipulation more consistently across the
kernel tree.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200108134324.46500-4-mark.rutland@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c2483f154 upstream.
When KVM injects an exception into a guest, it generates the CPSR value
from scratch, configuring CPSR.{M,A,I,T,E}, and setting all other
bits to zero.
This isn't correct, as the architecture specifies that some CPSR bits
are (conditionally) cleared or set upon an exception, and others are
unchanged from the original context.
This patch adds logic to match the architectural behaviour. To make this
simple to follow/audit/extend, documentation references are provided,
and bits are configured in order of their layout in SPSR_EL2. This
layout can be seen in the diagram on ARM DDI 0487E.a page C5-426.
Note that this code is used by both arm and arm64, and is intended to
fuction with the SPSR_EL2 and SPSR_HYP layouts.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200108134324.46500-3-mark.rutland@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A couple of fixes have come in that would be good to include in this
release:
- A fix for amount of memory on Beaglebone Black. Surfaced now since
GRUB2 doesn't update memory size in the booted kernel.
- A fix to make SPI interfaces work on am43x-epos-evm.
- Small Kconfig fix for OPTEE (adds a depend on MMU) to avoid build
failures.
-----BEGIN PGP SIGNATURE-----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=xQ63
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A couple of fixes have come in that would be good to include in this
release:
- A fix for amount of memory on Beaglebone Black. Surfaced now since
GRUB2 doesn't update memory size in the booted kernel.
- A fix to make SPI interfaces work on am43x-epos-evm.
- Small Kconfig fix for OPTEE (adds a depend on MMU) to avoid build
failures"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
tee: optee: Fix compilation issue with nommu
ARM: dts: am335x-boneblack-common: fix memory size
Looks like we have wrong default memory size for beaglebone black,
it has at least 512 MB of RAM and not 256 MB. This causes an issue
when booted with GRUB2 that does not seem to pass memory info to
the kernel.
And for am43x-epos-evm the SPI pin directions need to be configured
for SPI to work.
-----BEGIN PGP SIGNATURE-----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=XXZc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-fixes-whenever-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few minor fixes for omaps
Looks like we have wrong default memory size for beaglebone black,
it has at least 512 MB of RAM and not 256 MB. This causes an issue
when booted with GRUB2 that does not seem to pass memory info to
the kernel.
And for am43x-epos-evm the SPI pin directions need to be configured
for SPI to work.
* tag 'omap-for-fixes-whenever-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
ARM: dts: am335x-boneblack-common: fix memory size
Link: https://lore.kernel.org/r/pull-1579895109-287828@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Set d0 and d1 pin directions for spi0 and spi1 as per their pinmux.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Updates to the Generic Timer architecture allow ID_PFR1.GenTimer to
have values other than 0 or 1 while still preserving backward
compatibility. At the moment, Linux is quite strict in the way it
handles this field at early boot and will not configure arch timer if
it doesn't find the value 1.
Since here use ubfx for arch timer version extraction (hyb-stub build
with -march=armv7-a, so it is safe)
To help backports (even though the code was correct at the time of writing)
Fixes: 8ec58be9f3 ("ARM: virt: arch_timers: enable access to physical timers")
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
I've been sitting on these longer than I meant, so the patch count is
a bit higher than ideal for this part of the release. There's also some
reverts of double-applied patches that brings the diffstat up a bit.
With that said, the biggest changes are:
- Revert of duplicate i2c device addition on two Aspeed (BMC) Devicetrees.
- Move of two device nodes that got applied to the wrong part of the
tree on ASpeed G6.
- Regulator fix for Beaglebone X15 (adding 12/5V supplies)
- Use interrupts for keys on Amlogic SM1 to avoid missed polls
In addition to that, there is a collection of smaller DT fixes:
- Power supply assignment fixes for i.MX6
- Fix of interrupt line for magnetometer on i.MX8 Librem5 devkit
- Build fixlets (selects) for davinci/omap2+
- More interrupt number fixes for Stratix10, Amlogic SM1, etc.
- ... and more similar fixes across different platforms
And some non-DT stuff:
- optee fix to register multiple shared pages properly
- Clock calculation fixes for MMP3
- Clock fixes for OMAP as well
-----BEGIN PGP SIGNATURE-----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=MMJu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I've been sitting on these longer than I meant, so the patch count is
a bit higher than ideal for this part of the release. There's also
some reverts of double-applied patches that brings the diffstat up a
bit.
With that said, the biggest changes are:
- Revert of duplicate i2c device addition on two Aspeed (BMC)
Devicetrees.
- Move of two device nodes that got applied to the wrong part of the
tree on ASpeed G6.
- Regulator fix for Beaglebone X15 (adding 12/5V supplies)
- Use interrupts for keys on Amlogic SM1 to avoid missed polls
In addition to that, there is a collection of smaller DT fixes:
- Power supply assignment fixes for i.MX6
- Fix of interrupt line for magnetometer on i.MX8 Librem5 devkit
- Build fixlets (selects) for davinci/omap2+
- More interrupt number fixes for Stratix10, Amlogic SM1, etc.
- ... and more similar fixes across different platforms
And some non-DT stuff:
- optee fix to register multiple shared pages properly
- Clock calculation fixes for MMP3
- Clock fixes for OMAP as well"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
MAINTAINERS: Add myself as the co-maintainer for Actions Semi platforms
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
ARM: omap2plus: select RESET_CONTROLLER
ARM: davinci: select CONFIG_RESET_CONTROLLER
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
ARM: dts: mmp3: Fix the TWSI ranges
clk: mmp2: Fix the order of timer mux parents
ARM: mmp: do not divide the clock rate
arm64: dts: rockchip: Fix IR on Beelink A1
optee: Fix multi page dynamic shm pool alloc
...
BeagleBone Black series is equipped with 512MB RAM
whereas only 256MB is included from am335x-bone-common.dtsi
This leads to an issue with unusual setups when devicetree
is loaded by GRUB2 directly.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Fix i.MX8MM SDMA1 AHB clock setting to remove a "Timeout waiting for CH0"
error seen with UART1.
- Correct compatible of RV3029 RTC device on imx6q-dhcom board.
- Correct interrupt trigger type for magnetometer on board
imx8mq-librem5-devkit.
- A series from Anson Huang to fix vdd3p0 power supplier for a few NXP
development board.
- Fix imx6q-icore-mipi board to use 1.5 version of i.Core MX6DL, so
that Ethernet interface on the board works properly.
- Fix Toradex Colibri board to get NAND flash support back.
- Fix SGTL5000 VDDIO regulator connection for imx6q-dhcom, which
is connected to PMIC SW2 output rather than a fixed 3V3 rail.
- Fix 'reg' of CPU node on imx7ulp to get rid of a warning given by
kernel.
- Fix endian setting for DCFG on LS1028A SoC, so that register access
of DCFG becomes correct.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl4Xz5gUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM44xgf+J/WZaUY9S9tvl9w9kMdmmB71WSVY
qCgWTS6FUvw7AiJ+4mUzXXTP+Wwb0c1wBtvI4FRk6MhkHEc1nSkhJ5I9++bDD7BV
2ktAIJmC2uSHdazq/wjDMi4T6LGnmRv1xKkEvib2/CBVzET9PoGJY2stS8R0r2xf
WwCvMb0Lc7Twp0/nlY+h8ItHL50ZZuBSqW83P26zQdImHKMwRiAdlFa7eiZu82nV
sPadYbtf07yUfeLpUfYXo/nFZ+Q2c+tJGUNxm0hXGvc+FaWS4MM44luBTN2fpaVl
vAg2LKvdaWGbDZk0Q6WQdMsleDaHs3JdbaNrqBePbYyTnMll8N31ek3PWg==
=Hv2B
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.5, round 2:
- Fix i.MX8MM SDMA1 AHB clock setting to remove a "Timeout waiting for CH0"
error seen with UART1.
- Correct compatible of RV3029 RTC device on imx6q-dhcom board.
- Correct interrupt trigger type for magnetometer on board
imx8mq-librem5-devkit.
- A series from Anson Huang to fix vdd3p0 power supplier for a few NXP
development board.
- Fix imx6q-icore-mipi board to use 1.5 version of i.Core MX6DL, so
that Ethernet interface on the board works properly.
- Fix Toradex Colibri board to get NAND flash support back.
- Fix SGTL5000 VDDIO regulator connection for imx6q-dhcom, which
is connected to PMIC SW2 output rather than a fixed 3V3 rail.
- Fix 'reg' of CPU node on imx7ulp to get rid of a warning given by
kernel.
- Fix endian setting for DCFG on LS1028A SoC, so that register access
of DCFG becomes correct.
* tag 'imx-fixes-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
arm64: dts: imx8mq-librem5-devkit: use correct interrupt for the magnetometer
ARM: dts: imx6q-dhcom: Fix SGTL5000 VDDIO regulator connection
ARM: dts: imx7ulp: fix reg of cpu node
arm64: dts: imx8mm: Change SDMA1 ahb clock for imx8mm
arm64: dts: ls1028a: fix endian setting for dcfg
ARM: dts: imx6q-dhcom: fix rtc compatible
Link: https://lore.kernel.org/r/20200110011836.GW4456@T480
Signed-off-by: Olof Johansson <olof@lixom.net>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 96a9169cf6 ("ARM: dts: imx6sll-evk: Assign corresponding power supply for vdd3p0")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 3feea8805d ("ARM: dts: imx6sl-evk: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 37a4bdead1 ("ARM: dts: imx6sx-sdb: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 93385546ba ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Similar fix has merged for i.Core MX6Q but missed to update for DL.
Fixes: a8039f2dd0 ("ARM: dts: imx6dl: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes for some badly applied patches that went in to 5.5. There is also
a fix for an incorrect i2c address.
-----BEGIN PGP SIGNATURE-----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=JQMa
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.5-devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/fixes
ASPEED device tree fixes for 5.5
Fixes for some badly applied patches that went in to 5.5. There is also
a fix for an incorrect i2c address.
* tag 'aspeed-5.5-devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
Link: https://lore.kernel.org/r/CACPK8XcjazgORXNZBU1ECMukXG4HA8D9VeDxiSPifDk_iB7_dw@mail.gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
With the new omap_prm driver added unconditionally, omap2 builds
fail when the reset controller subsystem is disabled:
drivers/soc/ti/omap_prm.o: In function `omap_prm_probe':
omap_prm.c:(.text+0x2d4): undefined reference to `devm_reset_controller_register'
Link: https://lore.kernel.org/r/20191216132132.3330811-1-arnd@arndb.de
Fixes: 3e99cb214f ("soc: ti: add initial PRM driver with reset control support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Selecting RESET_CONTROLLER is actually required, otherwise we
can get a link failure in the clock driver:
drivers/clk/davinci/psc.o: In function `__davinci_psc_register_clocks':
psc.c:(.text+0x9a0): undefined reference to `devm_reset_controller_register'
drivers/clk/davinci/psc-da850.o: In function `da850_psc0_init':
psc-da850.c:(.text+0x24): undefined reference to `reset_controller_add_lookup'
Link: https://lore.kernel.org/r/20191210195202.622734-1-arnd@arndb.de
Fixes: f962396ce2 ("ARM: davinci: support multiplatform build for ARM v5")
Cc: <stable@vger.kernel.org> # v5.4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The PCA9552 used for fan fault and presence information is at address
61h, not 60h.
Fixes: 2efc118ce3 ("ARM: dts: aspeed: rainier: Add i2c devices")
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: rainier: Add i2c devices", which
was already applied to the tree.
Fixes: 9c44db7096 ("ARM: dts: aspeed: rainier: Add i2c devices")
Reviewed-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Tested-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: tacoma: Enable FMC and SPI
devices" which was already applied as part of "ARM: dts: aspeed: Add
Tacoma machine".
Fixes: 8737481e38 ("ARM: dts: aspeed: tacoma: Enable FMC and SPI devices")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: tacoma: Enable I2C busses", which
was already applied as part of "ARM: dts: aspeed: Add Tacoma machine".
Fixes: 606bcdde67 ("ARM: dts: aspeed: tacoma: Enable I2C busses")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
