commit f05f80f217 upstream.
The device ID 0xa70e is defined for the USB3 device controller in the CPU
sub-system of Raptor Lake platform. Hence updating the ID accordingly.
Fixes: bad0d1d726 ("usb: dwc3: pci: Add support for Intel Raptor Lake")
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20221125105327.27945-1-shruthi.sanil@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0dced9c7d upstream.
It can take more than one second to check each connector
when the system is resumed. So if you have, say, eight
connectors, it may take eight seconds for ucsi_resume() to
finish. That's a bit too much.
This will modify ucsi_resume() so that it schedules a work
where the interface is actually resumed instead of checking
the connectors directly. The connections will also be
checked in separate tasks which are queued for each connector
separately.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216706
Fixes: 99f6d43611 ("usb: typec: ucsi: Check the connection on resume")
Cc: <stable@vger.kernel.org>
Reported-by: Todd Brandt <todd.e.brandt@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221123093021.25981-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fed70b61ef upstream.
ADL-N systems have the same issue as ADL-P, where a large boot firmware
delay is seen if USB ports are left in U3 at shutdown. So apply the
XHCI_RESET_TO_DEFAULT quirk to ADL-N as well.
This patch depends on commit 34cd2db408 ("xhci: Add quirk to reset
host back to default state at shutdown").
The issue it fixes is a ~20s boot time delay when booting from S5. It
affects ADL-N devices, and ADL-N support was added starting from v5.16.
Cc: stable@vger.kernel.org
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 188c9c2e0c upstream.
The driver leaves the line speed unchanged in case a requested speed is
not supported. Make sure to handle the case where the current speed is
B0 (hangup) without dividing by zero when determining the clock source.
Fixes: 3aacac02f3 ("USB: serial: f81534: add high baud rate support")
Cc: stable@vger.kernel.org # 4.16
Cc: Ji-Ze Hong (Peter Hong) <hpeter@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a08ca6ebaf upstream.
The driver leaves the line speed unchanged in case a requested speed is
not supported. Make sure to handle the case where the current speed is
B0 (hangup) without dividing by zero when determining the clock source.
Fixes: 268ddb5e9b ("USB: serial: f81232: add high baud rate support")
Cc: stable@vger.kernel.org # 5.2
Cc: Ji-Ze Hong (Peter Hong) <hpeter@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e88906b169 upstream.
The RF sniffers are based on cp210x where the RF frontends
are based on a different USB stack.
RF sniffers can analyze packets meta data including power level
and perform packet injection.
Can be used to perform RF frontend self-test when connected to
a concentrator, ex. arch/arm/boot/dts/imx7d-flex-concentrator.dts
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c92670b16 upstream.
Setup function uvc_function_setup permits control transfer
requests with up to 64 bytes of payload (UVC_MAX_REQUEST_SIZE),
data stage handler for OUT transfer uses memcpy to copy req->actual
bytes to uvc_event->data.data array of size 60. This may result
in an overflow of 4 bytes.
Fixes: cdda479f15 ("USB gadget: video class function driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20221206141301.51305-1-szymon.heidrich@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch modifies the TD_SIZE in TRB before ZLP TRB.
The TD_SIZE in TRB before ZLP TRB must be set to 1 to force
processing ZLP TRB by controller.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20221115092218.421267-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until the endpoint is disabled, its descriptors should remain valid.
When its requests are removed from ep disable, the request completion
routine may attempt to access the endpoint's descriptor. Don't clear the
descriptors before that.
Fixes: f09ddcfcb8 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/45db7c83b209259115bf652af210f8b2b3b1a383.1668561364.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core DWC3 device node was not properly removed by the custom
dwc3_exynos_remove_child() function. Replace it with generic
of_platform_depopulate() which does that job right.
Fixes: adcf20dcd2 ("usb: dwc3: exynos: Use of_platform API to create dwc3 core pdev")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20221110154131.2577-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During handling Clear Halt Endpoint Feature request, driver invokes
Reset Endpoint command. Because this command has some issue with
transition endpoint from Running to Idle state the driver must
stop the endpoint by using Stop Endpoint command.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20221110063005.370656-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there's a disconnection while operating in eSS, there may be a delay
in VBUS drop response from the connector. In that case, the internal
link state may drop to operate in usb2 speed while the controller thinks
the VBUS is still high. The driver must make sure to disable
GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed.
The End Transfer command may be called, and only that command needs to
go through at this point. Let's keep it simple and unconditionally
disable GUSB2PHYCFG.SUSPHY whenever we issue the command.
This scenario is not seen in real hardware. In a rare case, our
prototype type-c controller/interface may have a slow response
triggerring this issue.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5651117207803c26e2f22ddf4e5ce9e865dcf7c7.1668045468.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since e219a712bc (usb: gadget: uvc: add v4l2 try_format api call) the
try_format function is available. With this function includes checks for
valid configurations programmed in the configfs. We use this function to
ensure to return valid values on the set_format callback.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Fixes: e219a712bc ("usb: gadget: uvc: add v4l2 try_format api call")
Link: https://lore.kernel.org/r/20221026182240.363055-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids for 6.1.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCY3YdbAAKCRALxc3C7H1l
CG7TAQCAET51PBuwY6sxj0Fc2JvvdsY7iF7gOXO2x4dzoKbTGwEA9V3CTQFcJAwF
Iapf67+p42TdUePhJHwT+V4Ii+Bwdww=
=R8+X
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.1-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
"USB-serial fixes for 6.1-rc6
Here are some new modem device ids for 6.1.
All have been in linux-next with no reported issues."
* tag 'usb-serial-6.1-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add u-blox LARA-L6 modem
USB: serial: option: add u-blox LARA-R6 00B modem
USB: serial: option: remove old LARA-R6 PID
USB: serial: option: add Fibocom FM160 0x0111 composition
USB: serial: option: add Sierra Wireless EM9191
Add LARA-L6 PIDs for three different USB compositions.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In default mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
In CDC-ECM mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
[ johan: drop PID defines in favour of comments ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The official LARA-R6 (00B) modem uses 0x908b PID. LARA-R6 00B does not
implement a QMI interface on port 4, the reservation (RSVD(4)) has been
added to meet other companies that implement QMI on that interface.
LARA-R6 00B USB composition exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove the UBLOX_PRODUCT_R6XX 0x90fa association since LARA-R6 00B final
product uses a new USB composition with different PID. 0x90fa PID used
only by LARA-R6 internal prototypes.
Move 0x90fa PID directly in the option_ids array since used by other
Qualcomm based modem vendors as pointed out in:
https://lore.kernel.org/all/6572c4e6-d8bc-b8d3-4396-d879e4e76338@gmail.com
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Before adding this quirk, this (mechanical keyboard) device would not be
recognized, logging:
new full-speed USB device number 56 using xhci_hcd
unable to read config index 0 descriptor/start: -32
chopping to 0 config(s)
It would take dozens of plugging/unpuggling cycles for the keyboard to
be recognized. Keyboard seems to simply work after applying this quirk.
This issue had been reported by users in two places already ([1], [2])
but nobody tried upstreaming a patch yet. After testing I believe their
suggested fix (DELAY_INIT + NO_LPM + DEVICE_QUALIFIER) was probably a
little overkill. I assume this particular combination was tested because
it had been previously suggested in [3], but only NO_LPM seems
sufficient for this device.
[1]: https://qiita.com/float168/items/fed43d540c8e2201b543
[2]: https://blog.kostic.dev/posts/making-the-realforce-87ub-work-with-usb30-on-Ubuntu/
[3]: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1678477
Cc: stable@vger.kernel.org
Signed-off-by: Nicolas Dumazet <ndumazet@google.com>
Link: https://lore.kernel.org/r/20221109122946.706036-1-ndumazet@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When usb 3.0 hub connect with one USB 2.0 device and NO USB 3.0 device,
some usb hub reports endless port reset message.
[ 190.324169] usb 2-1: new SuperSpeed USB device number 88 using xhci-hcd
[ 190.352834] hub 2-1:1.0: USB hub found
[ 190.356995] hub 2-1:1.0: 4 ports detected
[ 190.700056] usb 2-1: USB disconnect, device number 88
[ 192.472139] usb 2-1: new SuperSpeed USB device number 89 using xhci-hcd
[ 192.500820] hub 2-1:1.0: USB hub found
[ 192.504977] hub 2-1:1.0: 4 ports detected
[ 192.852066] usb 2-1: USB disconnect, device number 89
The reason is the runtime pm state of USB2.0 port is active and
USB 3.0 port is suspend, so parent device is active state.
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb2/power/runtime_status
suspended
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb1/power/runtime_status
active
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/power/runtime_status
active
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/power/runtime_status
active
So xhci_cdns3_suspend_quirk() have not called. U3 configure is not applied.
move U3 configure into host start. Reinit again in resume function in case
controller power lost during suspend.
Cc: stable@vger.kernel.org 5.10
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221026190749.2280367-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a deadlock in ci_otg_del_timer(), the process is
shown below:
(thread 1) | (thread 2)
ci_otg_del_timer() | ci_otg_hrtimer_func()
... |
spin_lock_irqsave() //(1) | ...
... |
hrtimer_cancel() | spin_lock_irqsave() //(2)
(block forever)
We hold ci->lock in position (1) and use hrtimer_cancel() to
wait ci_otg_hrtimer_func() to stop, but ci_otg_hrtimer_func()
also need ci->lock in position (2). As a result, the
hrtimer_cancel() in ci_otg_del_timer() will be blocked forever.
This patch extracts hrtimer_cancel() from the protection of
spin_lock_irqsave() in order that the ci_otg_hrtimer_func()
could obtain the ci->lock.
What`s more, there will be no race happen. Because the
"next_timer" is always under the protection of
spin_lock_irqsave() and we only check whether "next_timer"
equals to NUM_OTG_FSM_TIMERS in the following code.
Fixes: 3a316ec4c9 ("usb: chipidea: use hrtimer for otg fsm timers")
Cc: stable <stable@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220918033312.94348-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change breaks device tree based platforms with PHY device and use
usb-role-switch instead of an extcon switch. extcon_find_edev_by_node()
will return EPROBE_DEFER if it can not find a device so probing without
an extcon device will be deferred indefinitely. Fix this by
explicitly checking for usb-role-switch.
At least the out-of-tree USB3 support on Apple silicon based platforms
using dwc3 with tipd USB Type-C and PD controller is affected by this
issue.
Fixes: d182c2e1bc ("usb: dwc3: Don't switch OTG -> peripheral if extcon is present")
Cc: stable@kernel.org
Signed-off-by: Janne Grunau <j@jannau.net>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20221106214804.2814-1-j@jannau.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If reading TPS_REG_INT_EVENT1/2 fails in the interrupt handler event1
and event2 may be uninitialized when they are used to determine
IRQ_HANDLED vs. IRQ_NONE in the error path.
Fixes: c7260e29dd ("usb: typec: tipd: Add short-circuit for no irqs")
Fixes: 45188f27b3 ("usb: typec: tipd: Add support for Apple CD321X")
Cc: stable <stable@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/20221102161542.30669-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point to enter safe mode during DP/TBT configuration
if the DP/TBT was already configured in mux. This is because safe
mode is only applicable when there is a need to reconfigure the
pins in order to avoid damage within/to port partner.
In some chrome systems, IOM/mux is already configured before OS
comes up. Thus, when driver is probed, it blindly enters safe
mode due to PD negotiations but only after gfx driver lowers
dp_phy_ownership, will the IOM complete safe mode and send an
ack to PMC.
Since, that never happens, we see IPC timeout.
Hence, allow safe mode only when pin reconfiguration is not
required, which makes sense.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Cc: stable <stable@kernel.org>
Signed-off-by: Rajat Khandelwal <rajat.khandelwal@linux.intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221024171611.181468-1-rajat.khandelwal@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6000b8d900.
The offending commit disabled the USB core PHY management as the dwc3
already manages the PHYs in question.
Unfortunately some platforms have started relying on having USB core
also controlling the PHY and this is specifically currently needed on
some Exynos platforms for PHY calibration or connected device may fail
to enumerate.
The PHY calibration was previously handled in the dwc3 driver, but to
work around some issues related to how the dwc3 driver interacts with
xhci (e.g. using multiple drivers) this was moved to USB core by commits
34c7ed72f4 ("usb: core: phy: add support for PHY calibration") and
a0a465569b ("usb: dwc3: remove generic PHY calibrate() calls").
The same PHY obviously should not be controlled from two different
places, which for example do no agree on the PHY mode or power state
during suspend, but as the offending patch was backported to stable,
let's revert it for now.
Reported-by: Stefan Agner <stefan@agner.ch>
Link: https://lore.kernel.org/lkml/808bdba846bb60456adf10a3016911ee@agner.ch/
Fixes: 6000b8d900 ("usb: dwc3: disable USB core PHY management")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20221103144648.14197-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
What the code does is to not check the return value from
devm_gpiod_get() and then avoid using an erroneous GPIO descriptor
with IS_ERR_OR_NULL().
This will miss real errors from the GPIO core that should not be
ignored, such as probe deferral.
Instead request the GPIO as explicitly optional, which means that
if it doesn't exist, the descriptor returned will be NULL.
Then we can add error handling and also avoid just doing this on
the device tree path, and simplify the site where the optional
GPIO descriptor is used.
There were some problems with cleaning up this GPIO descriptor
use in the past, but this is the proper way to deal with it.
Cc: Rafał Miłecki <rafal@milecki.pl>
Cc: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20221107090753.1404679-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A use-after-free bugfix in the smscufx driver and various minor
error path fixes, smaller build fixes, sysfs fixes and
typos in comments in the stifb, sisfb, da8xxfb, xilinxfb, sm501fb,
gbefb and cyber2000fb drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCY16ulQAKCRD3ErUQojoP
XyvDAP9ZhF0SjbnRBwHAU9ZYC7XpCwcoqBRWFCCU7mmmbkXrJAD9F1LcEwZPGyn/
5/hiTwzM8ioJz6HB3r04M88bl4b1cwI=
=SnCh
-----END PGP SIGNATURE-----
Merge tag 'fbdev-for-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes from Helge Deller:
"A use-after-free bugfix in the smscufx driver and various minor error
path fixes, smaller build fixes, sysfs fixes and typos in comments in
the stifb, sisfb, da8xxfb, xilinxfb, sm501fb, gbefb and cyber2000fb
drivers"
* tag 'fbdev-for-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: cyber2000fb: fix missing pci_disable_device()
fbdev: sisfb: use explicitly signed char
fbdev: smscufx: Fix several use-after-free bugs
fbdev: xilinxfb: Make xilinxfb_release() return void
fbdev: sisfb: fix repeated word in comment
fbdev: gbefb: Convert sysfs snprintf to sysfs_emit
fbdev: sm501fb: Convert sysfs snprintf to sysfs_emit
fbdev: stifb: Fall back to cfb_fillrect() on 32-bit HCRX cards
fbdev: da8xx-fb: Fix error handling in .remove()
fbdev: MIPS supports iomem addresses
The gadget driver may have a certain expectation of how the request
completion flow should be from to its configuration. Make sure the
controller driver respect that. That is, don't set IMI (Interrupt on
Missed Isoc) when usb_request->no_interrupt is set. Also, the driver
should only set IMI to the last TRB of a chain.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/ced336c84434571340c07994e3667a0ee284fefe.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When servicing a transfer completion event, the dwc3 driver will reclaim
TRBs of started requests up to the request associated with the interrupt
event. Currently we don't check for interrupt due to missed isoc, and
the driver may attempt to reclaim TRBs beyond the associated event. This
causes invalid memory access when the hardware still owns the TRB. If
there's a missed isoc TRB with IMI (interrupt on missed isoc), make sure
to stop servicing further.
Note that only the last TRB of chained TRBs has its status updated with
missed isoc.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Reported-by: Jeff Vanhoof <jdv1029@gmail.com>
Reported-by: Dan Vacura <w36195@motorola.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/b29acbeab531b666095dfdafd8cb5c7654fbb3e1.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 19905240ae.
It was a new feature, and it doesn't even work properly yet, so revert
it from this branch as it is not needed for 6.1-final.
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@kernel.org>
Fixes: 19905240ae ("usb: gadget: uvc: limit isoc_sg to super speed gadgets")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoints are normally deleted from the bandwidth list when they are
dropped, before the virt device is freed.
If xHC host is dying or being removed then the endpoints aren't dropped
cleanly due to functions returning early to avoid interacting with a
non-accessible host controller.
So check and delete endpoints that are still on the bandwidth list when
freeing the virt device.
Solves a list_del corruption kernel crash when unbinding xhci-pci,
caused by xhci_mem_cleanup() when it later tried to delete already freed
endpoints from the bandwidth list.
This only affects hosts that use software bandwidth checking, which
currenty is only the xHC in intel Panther Point PCH (Ivy Bridge)
Cc: stable@vger.kernel.org
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-5-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For optimal power consumption of USB4 routers the XHCI PCIe endpoint
used for tunneling must be in D3. Historically this is accomplished
by a long list of PCIe IDs that correspond to these endpoints because
the xhci_hcd driver will not default to allowing runtime PM for all
devices.
As both AMD and Intel have released new products with new XHCI controllers
this list continues to grow. In reviewing the XHCI specification v1.2 on
page 607 there is already a requirement that the PCI power management
states D3hot and D3cold must be supported.
In the quirk list, use this to indicate that runtime PM should be allowed
on XHCI controllers. The following controllers are known to be xHC 1.2 and
dropped explicitly:
* AMD Yellow Carp
* Intel Alder Lake
* Intel Meteor Lake
* Intel Raptor Lake
[keep PCI ID for Alder Lake PCH for recently added quirk -Mathias]
Cc: stable@vger.kernel.org
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://www.intel.com/content/dam/www/public/us/en/documents/technical-specifications/extensible-host-controler-interface-usb-xhci.pdf
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-4-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems based on Alder Lake P see significant boot time delay if
boot firmware tries to control usb ports in unexpected link states.
This is seen with self-powered usb devices that survive in U3 link
suspended state over S5.
A more generic solution to power off ports at shutdown was attempted in
commit 83810f84ec ("xhci: turn off port power in shutdown")
but it caused regression.
Add host specific XHCI_RESET_TO_DEFAULT quirk which will reset host and
ports back to default state in shutdown.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-3-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This appears to fix the error:
"xhci_hcd <address>; ERROR Transfer event TRB DMA ptr not part of
current TD ep_index 2 comp_code 13" that appear spuriously (or pretty
often) when using a r8152 USB3 ethernet adapter with integrated hub.
ASM1042 reports as a 0.96 controller, but appears to behave more like 1.0
Inspired by this email thread: https://markmail.org/thread/7vzqbe7t6du6qsw3
Cc: stable@vger.kernel.org
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-2-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To ensure that child node is found, don't rely on child's node name
which can take different value, but on child's compatible name.
Fixes: f5c5936d6b ("usb: dwc3: st: Fix node's child name")
Cc: stable <stable@kernel.org>
Cc: Jerome Audu <jerome.audu@st.com>
Reported-by: Felipe Balbi <felipe@balbi.sh>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220930142018.890535-1-patrice.chotard@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The overhead of preparing sg data is high for transfers with limited
payload. When transferring isoc over high-speed usb the maximum payload
is rather small which is a good argument no to use sg. This patch is
changing the uvc_video_encode_isoc_sg encode function only to be used
for super speed gadgets.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20221017221141.3134818-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With char becoming unsigned by default, and with `char` alone being
ambiguous and based on architecture, signed chars need to be marked
explicitly as such. This fixes warnings like:
drivers/video/fbdev/sis/init301.c:3549 SiS_GetCRT2Data301() warn: 'SiS_Pr->SiS_EModeIDTable[ModeIdIndex]->ROMMODEIDX661' is unsigned
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-usb@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Helge Deller <deller@gmx.de>
When port is connected and then disconnected, the state stays as
configured. Which is incorrect as the port is no longer configured,
but in a not attached state.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: efed421a94 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/1664997235-18198-1-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking the connection status of every port on resume. This
fixes an issue where the partner device is not unregistered
properly after resume if it was unplugged while the system
was suspended.
The function ucsi_check_connection() is also modified so
that it can be used also for registering the connection on
top of unregistering it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=210425
Fixes: a94ecde41f ("usb: typec: ucsi: ccg: enable runtime pm support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221007100951.43798-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit fc274c1e99 ("USB: gadget: Add a new bus for gadgets"),
the gadget devices are proper driver core devices, which caused each
device to request pinmux settings:
aspeed_vhub 1e6a0000.usb-vhub: Initialized virtual hub in USB2 mode
aspeed-g5-pinctrl 1e6e2080.pinctrl: pin A7 already requested by 1e6a0000.usb-vhub; cannot claim for gadget.0
aspeed-g5-pinctrl 1e6e2080.pinctrl: pin-232 (gadget.0) status -22
aspeed-g5-pinctrl 1e6e2080.pinctrl: could not request pin 232 (A7) from group USB2AD on device aspeed-g5-pinctrl
g_mass_storage gadget.0: Error applying setting, reverse things back
The vhub driver has already claimed the pins, so prevent the gadgets
from requesting them too by setting the magic of_node_reused flag. This
causes the driver core to skip the mux request.
Reported-by: Zev Weiss <zev@bewilderbeest.net>
Reported-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Fixes: fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
Cc: stable@vger.kernel.org
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Link: https://lore.kernel.org/r/20221017053006.358520-1-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uvc_video_encode_isoc_sg, the uvc_request's sg list is
incorrectly being populated leading to corrupt video being
received by the remote end. When building the sg list the
usage of buf->sg's 'dma_length' field is not correct and
instead its 'length' field should be used.
Fixes: e81e7f9a0e ("usb: gadget: uvc: add scatter gather support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jeff Vanhoof <qjv001@motorola.com>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20221018215044.765044-5-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is a transmission error the buffer will be returned too early,
causing a memory fault as subsequent requests for that buffer are still
queued up to be sent. Refactor the error handling to wait for the final
request to come in before reporting back the buffer to userspace for all
transfer types (bulk/isoc/isoc_sg). This ensures userspace knows if the
frame was successfully sent.
Fixes: e81e7f9a0e ("usb: gadget: uvc: add scatter gather support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20221018215044.765044-4-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the re-use of the previous completion status in 0d1c407b1a
("usb: dwc3: gadget: Return proper request status") it could be possible
that the next frame would also get dropped if the current frame has a
missed isoc error. Ensure that an interrupt is requested for the start
of a new frame.
Fixes: fc78941d81 ("usb: gadget: uvc: decrease the interrupt load to a quarter")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20221018215044.765044-2-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget driver may wait on the request completion when it sets the
USB_GADGET_DELAYED_STATUS. Make sure that the End Transfer command can
go through if the dwc->delayed_status is set so that the request can
complete. When the delayed_status is set, the Setup packet is already
processed, and the next phase should be either Data or Status. It's
unlikely that the host would cancel the control transfer and send a new
Setup packet during End Transfer command. But if that's the case, we can
try again when ep0state returns to EP0_SETUP_PHASE.
Fixes: e1ee843488 ("usb: dwc3: gadget: Force sending delayed status during soft disconnect")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3f9f59e5d74efcbaee444cf4b30ef639cc7b124e.1666146954.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the extcon device exists, get the mode from the extcon device. If
the controller is DRD and the driver is unable to determine the mode,
only then default the dr_mode to USB_DR_MODE_PERIPHERAL.
Reported-by: Steev Klimaszewski <steev@kali.org>
Fixes: 7a84e7353e ("Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"")
Cc: stable <stable@kernel.org>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20221017233510.53336-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
linux-next for a couple of months without, to my knowledge, any negative
reports (or any positive ones, come to that).
- Also the Maple Tree from Liam R. Howlett. An overlapping range-based
tree for vmas. It it apparently slight more efficient in its own right,
but is mainly targeted at enabling work to reduce mmap_lock contention.
Liam has identified a number of other tree users in the kernel which
could be beneficially onverted to mapletrees.
Yu Zhao has identified a hard-to-hit but "easy to fix" lockdep splat
(https://lkml.kernel.org/r/CAOUHufZabH85CeUN-MEMgL8gJGzJEWUrkiM58JkTbBhh-jew0Q@mail.gmail.com).
This has yet to be addressed due to Liam's unfortunately timed
vacation. He is now back and we'll get this fixed up.
- Dmitry Vyukov introduces KMSAN: the Kernel Memory Sanitizer. It uses
clang-generated instrumentation to detect used-unintialized bugs down to
the single bit level.
KMSAN keeps finding bugs. New ones, as well as the legacy ones.
- Yang Shi adds a userspace mechanism (madvise) to induce a collapse of
memory into THPs.
- Zach O'Keefe has expanded Yang Shi's madvise(MADV_COLLAPSE) to support
file/shmem-backed pages.
- userfaultfd updates from Axel Rasmussen
- zsmalloc cleanups from Alexey Romanov
- cleanups from Miaohe Lin: vmscan, hugetlb_cgroup, hugetlb and memory-failure
- Huang Ying adds enhancements to NUMA balancing memory tiering mode's
page promotion, with a new way of detecting hot pages.
- memcg updates from Shakeel Butt: charging optimizations and reduced
memory consumption.
- memcg cleanups from Kairui Song.
- memcg fixes and cleanups from Johannes Weiner.
- Vishal Moola provides more folio conversions
- Zhang Yi removed ll_rw_block() :(
- migration enhancements from Peter Xu
- migration error-path bugfixes from Huang Ying
- Aneesh Kumar added ability for a device driver to alter the memory
tiering promotion paths. For optimizations by PMEM drivers, DRM
drivers, etc.
- vma merging improvements from Jakub Matěn.
- NUMA hinting cleanups from David Hildenbrand.
- xu xin added aditional userspace visibility into KSM merging activity.
- THP & KSM code consolidation from Qi Zheng.
- more folio work from Matthew Wilcox.
- KASAN updates from Andrey Konovalov.
- DAMON cleanups from Kaixu Xia.
- DAMON work from SeongJae Park: fixes, cleanups.
- hugetlb sysfs cleanups from Muchun Song.
- Mike Kravetz fixes locking issues in hugetlbfs and in hugetlb core.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCY0HaPgAKCRDdBJ7gKXxA
joPjAQDZ5LlRCMWZ1oxLP2NOTp6nm63q9PWcGnmY50FjD/dNlwEAnx7OejCLWGWf
bbTuk6U2+TKgJa4X7+pbbejeoqnt5QU=
=xfWx
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2022-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Yu Zhao's Multi-Gen LRU patches are here. They've been under test in
linux-next for a couple of months without, to my knowledge, any
negative reports (or any positive ones, come to that).
- Also the Maple Tree from Liam Howlett. An overlapping range-based
tree for vmas. It it apparently slightly more efficient in its own
right, but is mainly targeted at enabling work to reduce mmap_lock
contention.
Liam has identified a number of other tree users in the kernel which
could be beneficially onverted to mapletrees.
Yu Zhao has identified a hard-to-hit but "easy to fix" lockdep splat
at [1]. This has yet to be addressed due to Liam's unfortunately
timed vacation. He is now back and we'll get this fixed up.
- Dmitry Vyukov introduces KMSAN: the Kernel Memory Sanitizer. It uses
clang-generated instrumentation to detect used-unintialized bugs down
to the single bit level.
KMSAN keeps finding bugs. New ones, as well as the legacy ones.
- Yang Shi adds a userspace mechanism (madvise) to induce a collapse of
memory into THPs.
- Zach O'Keefe has expanded Yang Shi's madvise(MADV_COLLAPSE) to
support file/shmem-backed pages.
- userfaultfd updates from Axel Rasmussen
- zsmalloc cleanups from Alexey Romanov
- cleanups from Miaohe Lin: vmscan, hugetlb_cgroup, hugetlb and
memory-failure
- Huang Ying adds enhancements to NUMA balancing memory tiering mode's
page promotion, with a new way of detecting hot pages.
- memcg updates from Shakeel Butt: charging optimizations and reduced
memory consumption.
- memcg cleanups from Kairui Song.
- memcg fixes and cleanups from Johannes Weiner.
- Vishal Moola provides more folio conversions
- Zhang Yi removed ll_rw_block() :(
- migration enhancements from Peter Xu
- migration error-path bugfixes from Huang Ying
- Aneesh Kumar added ability for a device driver to alter the memory
tiering promotion paths. For optimizations by PMEM drivers, DRM
drivers, etc.
- vma merging improvements from Jakub Matěn.
- NUMA hinting cleanups from David Hildenbrand.
- xu xin added aditional userspace visibility into KSM merging
activity.
- THP & KSM code consolidation from Qi Zheng.
- more folio work from Matthew Wilcox.
- KASAN updates from Andrey Konovalov.
- DAMON cleanups from Kaixu Xia.
- DAMON work from SeongJae Park: fixes, cleanups.
- hugetlb sysfs cleanups from Muchun Song.
- Mike Kravetz fixes locking issues in hugetlbfs and in hugetlb core.
Link: https://lkml.kernel.org/r/CAOUHufZabH85CeUN-MEMgL8gJGzJEWUrkiM58JkTbBhh-jew0Q@mail.gmail.com [1]
* tag 'mm-stable-2022-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (555 commits)
hugetlb: allocate vma lock for all sharable vmas
hugetlb: take hugetlb vma_lock when clearing vma_lock->vma pointer
hugetlb: fix vma lock handling during split vma and range unmapping
mglru: mm/vmscan.c: fix imprecise comments
mm/mglru: don't sync disk for each aging cycle
mm: memcontrol: drop dead CONFIG_MEMCG_SWAP config symbol
mm: memcontrol: use do_memsw_account() in a few more places
mm: memcontrol: deprecate swapaccounting=0 mode
mm: memcontrol: don't allocate cgroup swap arrays when memcg is disabled
mm/secretmem: remove reduntant return value
mm/hugetlb: add available_huge_pages() func
mm: remove unused inline functions from include/linux/mm_inline.h
selftests/vm: add selftest for MADV_COLLAPSE of uffd-minor memory
selftests/vm: add file/shmem MADV_COLLAPSE selftest for cleared pmd
selftests/vm: add thp collapse shmem testing
selftests/vm: add thp collapse file and tmpfs testing
selftests/vm: modularize thp collapse memory operations
selftests/vm: dedup THP helpers
mm/khugepaged: add tracepoint to hpage_collapse_scan_file()
mm/madvise: add file and shmem support to MADV_COLLAPSE
...
