commit 9c33663af9 upstream.
This patch adds code to check HCI_UART_PROTO_READY flag before
accessing hci_uart->proto. It fixes the race condition in
hci_uart_tty_ioctl() between HCIUARTSETPROTO and HCIUARTGETPROTO.
This issue bug found by Yu Hao and Weiteng Chen:
BUG: general protection fault in hci_uart_tty_ioctl [1]
The information of C reproducer can also reference the link [2]
Reported-by: Yu Hao <yhao016@ucr.edu>
Closes: https://lore.kernel.org/all/CA+UBctC3p49aTgzbVgkSZ2+TQcqq4fPDO7yZitFT5uBPDeCO2g@mail.gmail.com/ [1]
Reported-by: Weiteng Chen <wchen130@ucr.edu>
Closes: https://lore.kernel.org/lkml/CA+UBctDPEvHdkHMwD340=n02rh+jNRJNNQ5LBZNA+Wm4Keh2ow@mail.gmail.com/T/ [2]
Signed-off-by: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88e72239ea upstream.
Commit 272970be3d ("Bluetooth: hci_qca: Fix driver shutdown on closed
serdev") will cause below regression issue:
BT can't be enabled after below steps:
cold boot -> enable BT -> disable BT -> warm reboot -> BT enable failure
if property enable-gpios is not configured within DT|ACPI for QCA6390.
The commit is to fix a use-after-free issue within qca_serdev_shutdown()
by adding condition to avoid the serdev is flushed or wrote after closed
but also introduces this regression issue regarding above steps since the
VSC is not sent to reset controller during warm reboot.
Fixed by sending the VSC to reset controller within qca_serdev_shutdown()
once BT was ever enabled, and the use-after-free issue is also fixed by
this change since the serdev is still opened before it is flushed or wrote.
Verified by the reported machine Dell XPS 13 9310 laptop over below two
kernel commits:
commit e00fc2700a3f ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of bluetooth-next tree.
commit b23d98d46d ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of linus mainline tree.
Fixes: 272970be3d ("Bluetooth: hci_qca: Fix driver shutdown on closed serdev")
Cc: stable@vger.kernel.org
Reported-by: Wren Turkal <wt@penguintechs.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218726
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Wren Turkal <wt@penguintechs.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd336649ba upstream.
The default device address apparently comes from the NVM configuration
file and can differ quite a bit between controllers.
Store the default address when parsing the configuration file and use it
to determine whether the controller has been provisioned with an
address.
This makes sure that devices without a unique address start as
unconfigured unless a valid address has been provided in the devicetree.
Fixes: 32868e126c ("Bluetooth: qca: fix invalid device address check")
Cc: stable@vger.kernel.org # 6.5
Cc: Doug Anderson <dianders@chromium.org>
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c39332d0 upstream.
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This address is now used to determine if a controller has a valid
address or if one needs to be provided through devicetree or by user
space before the controller can be used.
It turns out that the WCN3991 controllers used in Chromium Trogdor
machines use a different default address, 39:98:00:00:5a:ad, which also
needs to be marked as invalid so that the correct address is fetched
from the devicetree.
Qualcomm has unfortunately not yet provided any answers as to whether
the 39:98 encodes a hardware id and if there are other variants of the
default address that needs to be handled by the driver.
For now, add the Trogdor WCN3991 default address to the device address
check to avoid having these controllers start with the default address
instead of their assigned addresses.
Fixes: 32868e126c ("Bluetooth: qca: fix invalid device address check")
Cc: stable@vger.kernel.org # 6.5
Cc: Doug Anderson <dianders@chromium.org>
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 32868e126c ]
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This was previously believed to be due to lack of persistent storage for
the address but it may also be due to integrators opting to not use the
on-chip OTP memory and instead store the address elsewhere (e.g. in
storage managed by secure world firmware).
According to Qualcomm, at least WCN6750, WCN6855 and WCN7850 have
on-chip OTP storage for the address.
As the device type alone cannot be used to determine when the address is
valid, instead read back the address during setup() and only set the
HCI_QUIRK_USE_BDADDR_PROPERTY flag when needed.
This specifically makes sure that controllers that have been provisioned
with an address do not start as unconfigured.
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Link: https://lore.kernel.org/r/124a7d54-5a18-4be7-9a76-a12017f6cce5@quicinc.com/
Fixes: 5971752de4 ("Bluetooth: hci_qca: Set HCI_QUIRK_USE_BDADDR_PROPERTY for wcn3990")
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bb23f07cb6 upstream.
Add missing MODULE_FIRMWARE declarations for firmware referenced in
btrtl.c.
Signed-off-by: Dan Gora <dan.gora@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40d442f969 upstream.
A recent commit fixed the code that parses the firmware files before
downloading them to the controller but introduced a memory leak in case
the sanity checks ever fail.
Make sure to free the firmware buffer before returning on errors.
Fixes: f905ae0be4b7 ("Bluetooth: qca: add missing firmware sanity checks")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cda0d6a198 upstream.
Add the missing sanity checks and move the 255-byte build-id buffer off
the stack to avoid leaking stack data through debugfs in case the
build-info reply is malformed.
Fixes: c0187b0bd3 ("Bluetooth: btqca: Add support to read FW build version for WCN3991 BTSoC")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0adcf6be14 upstream.
Add the missing sanity check when fetching the board id to avoid leaking
slab data when later requesting the firmware.
Fixes: a7f8dedb4b ("Bluetooth: qca: add support for QCA2066")
Cc: stable@vger.kernel.org # 6.7
Cc: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a112d3c72a upstream.
The NVM configuration files used by WCN3988 and WCN3990/1/8 have two
sets of configuration tags that are enclosed by a type-length header of
type four which the current parser fails to account for.
Instead the driver happily parses random data as if it were valid tags,
something which can lead to the configuration data being corrupted if it
ever encounters the words 0x0011 or 0x001b.
As is clear from commit b63882549b ("Bluetooth: btqca: Fix the NVM
baudrate tag offcet for wcn3991") the intention has always been to
process the configuration data also for WCN3991 and WCN3998 which
encodes the baud rate at a different offset.
Fix the parser so that it can handle the WCN3xxx configuration files,
which has an enclosing type-length header of type four and two sets of
TLV tags enclosed by a type-length header of type two and three,
respectively.
Note that only the first set, which contains the tags the driver is
currently looking for, will be parsed for now.
With the parser fixed, the software in-band sleep bit will now be set
for WCN3991 and WCN3998 (as it is for later controllers) and the default
baud rate 3200000 may be updated by the driver also for WCN3xxx
controllers.
Notably the deep-sleep feature bit is already set by default in all
configuration files in linux-firmware.
Fixes: 4219d46868 ("Bluetooth: btqca: Add wcn3990 firmware download support.")
Cc: stable@vger.kernel.org # 4.19
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e4edfa1e2 upstream.
Add the missing sanity checks when parsing the firmware files before
downloading them to avoid accessing and corrupting memory beyond the
vmalloced buffer.
Fixes: 83e81961ff ("Bluetooth: btqca: Introduce generic QCA ROME support")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a7f8dedb4b ]
This patch adds support for QCA2066 firmware patch and NVM downloading.
as the RF performance of QCA2066 SOC chip from different foundries may
vary. Therefore we use different NVM to configure them based on board ID.
Changes in v2
- optimize the function qca_generate_hsp_nvm_name
- remove redundant debug code for function qca_read_fw_board_id
Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 32868e126c ("Bluetooth: qca: fix invalid device address check")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 73e87c0a49 upstream.
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
wakeup() is called for a non-serdev controller during suspend.
Just return true for now to restore the original behaviour and address
the crash with pre-6.2 kernels, which do not have commit e9b3e5b8c6
("Bluetooth: hci_qca: only assign wakeup with serial port support") that
causes the crash to happen already at setup() time.
Fixes: c1a74160ea ("Bluetooth: hci_qca: Add device_may_wakeup support")
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d05fc8223 ]
Any return value from gpiod_get_optional() other than a pointer to a
GPIO descriptor or a NULL-pointer is an error and the driver should
abort probing. That being said: commit 56d074d26c ("Bluetooth: hci_qca:
don't use IS_ERR_OR_NULL() with gpiod_get_optional()") no longer sets
power_ctrl_enabled on NULL-pointer returned by
devm_gpiod_get_optional(). Restore this behavior but bail-out on errors.
While at it: also bail-out on error returned when trying to get the
"swctrl" GPIO.
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Closes: https://lore.kernel.org/linux-bluetooth/1713449192-25926-2-git-send-email-quic_zijuhu@quicinc.com/
Fixes: 56d074d26c ("Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Krzysztof Kozlowski<krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e465a07cd ]
Since dracut refers to the module info for defining the required
firmware files and btmtk driver doesn't provide the firmware info for
MT7922, the generate initrd misses the firmware, resulting in the
broken Bluetooth.
This patch simply adds the MODULE_FIRMWARE() for the missing entry
for covering that.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1214133
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b79e040910 ]
If hci_cmd_sync_complete() is triggered and skb is NULL, then
hdev->req_skb is NULL, which will cause this issue.
Reported-and-tested-by: syzbot+830d9e3fa61968246abd@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 77f45cca8b upstream.
The WCN6855 firmware on the Lenovo ThinkPad X13s expects the Bluetooth
device address in big-endian order when setting it using the
EDL_WRITE_BD_ADDR_OPCODE command.
Presumably, this is the case for all non-ROME devices which all use the
EDL_WRITE_BD_ADDR_OPCODE command for this (unlike the ROME devices which
use a different command and expect the address in little-endian order).
Reverse the little-endian address before setting it to make sure that
the address can be configured using tools like btmgmt or using the
'local-bd-address' devicetree property.
Note that this can potentially break systems with boot firmware which
has started relying on the broken behaviour and is incorrectly passing
the address via devicetree in big-endian order.
The only device affected by this should be the WCN3991 used in some
Chromebooks. As ChromeOS updates the kernel and devicetree in lockstep,
the new 'qcom,local-bd-address-broken' property can be used to determine
if the firmware is buggy so that the underlying driver bug can be fixed
without breaking backwards compatibility.
Set the HCI_QUIRK_BDADDR_PROPERTY_BROKEN quirk for such platforms so
that the address is reversed when parsing the address property.
Fixes: 5c0a1001c8 ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org # 5.1
Cc: Balakrishna Godavarthi <quic_bgodavar@quicinc.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Nikita Travkin <nikita@trvn.ru> # sc7180
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4790a73ace upstream.
This reverts commit 7dcd3e014a.
Qualcomm Bluetooth controllers like WCN6855 do not have persistent
storage for the Bluetooth address and must therefore start as
unconfigured to allow the user to set a valid address unless one has
been provided by the boot firmware in the devicetree.
A recent change snuck into v6.8-rc7 and incorrectly started marking the
default (non-unique) address as valid. This specifically also breaks the
Bluetooth setup for some user of the Lenovo ThinkPad X13s.
Note that this is the second time Qualcomm breaks the driver this way
and that this was fixed last year by commit 6945795bc8 ("Bluetooth:
fix use-bdaddr-property quirk"), which also has some further details.
Fixes: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Cc: stable@vger.kernel.org # 6.8
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56d074d26c ]
The optional variants for the gpiod_get() family of functions return NULL
if the GPIO in question is not associated with this device. They return
ERR_PTR() on any other error. NULL descriptors are graciously handled by
GPIOLIB and can be safely passed to any of the GPIO consumer interfaces
as they will return 0 and act as if the function succeeded. If one is
using the optional variant, then there's no point in checking for NULL.
Fixes: 6845667146 ("Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probe")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dcd3e014a ]
BT adapter going into UNCONFIGURED state during BT turn ON when
devicetree has no local-bd-address node.
Bluetooth will not work out of the box on such devices, to avoid this
problem, added check to set HCI_QUIRK_USE_BDADDR_PROPERTY based on
local-bd-address node entry.
When this quirk is not set, the public Bluetooth address read by host
from controller though HCI Read BD Address command is
considered as valid.
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0c1278ac8 ]
Add support for the WCN7850 Bluetooth chipset.
Tested on the SM8550 QRD platform.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 691d54d0f7 ]
Use switch/case to handle soc type specific behaviour,
the permit dropping the qca_is_xxx() inline functions
and make the code clearer and easier to update for new
SoCs.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f904feefe6 ]
Add support for the Bluetooth chip codenamed APACHE which is part of
WCN3988.
The firmware for this chip has a slightly different naming scheme
compared to most others. For ROM Version 0x0200 we need to use
apbtfw10.tlv + apnv10.bin and for ROM version 0x201 apbtfw11.tlv +
apnv11.bin
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8153b738bc ]
Use le32_to_cpu for ver.soc_id to fix the following
sparse warning.
drivers/bluetooth/btqca.c:640:24: sparse: warning: restricted
__le32 degrades to integer
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 095327fede ]
Add regulators, GPIOs and changes required to power on/off wcn6855.
Add support for firmware download for wcn6855 which is in the
linux-firmware repository as hpbtfw21.tlv and hpnv21.bin.
Based on the assumption that this is similar to the wcn6750
Tested-on: BTFW.HSP.2.1.0-00538-VER_PATCHZ-1
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44fac8a2fd ]
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/bluetooth/hci_qca.c:1869:37: error: ‘qca_soc_data_wcn6750’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1853:37: error: ‘qca_soc_data_wcn3998’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1841:37: error: ‘qca_soc_data_wcn3991’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1830:37: error: ‘qca_soc_data_wcn3990’
defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d192b697c ]
Set both WIDEBAND_SPEECH_SUPPORTED and VALID_LE_STATES quirks
for QCA2066.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64057f051f ]
Serdev recv_buf() callback is supposed to return the amount of bytes
consumed, therefore an int in between 0 and count.
Do not return negative number in case of issue, just print an error and
return count. This fixes a WARN in ttyport_receive_buf().
Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/
Fixes: 7237c4c9ec ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 187f8b648c ]
We should send hci reset command before bt turn off, which can reset bt
firmware status.
Signed-off-by: Rocky Liao <quic_rjliao@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 92d4abd66f upstream.
When the vhci device is opened in the two-step way, i.e.: open device
then write a vendor packet with requested controller type, the device
shall respond with a vendor packet which includes HCI index of created
interface.
When the virtual HCI is created, the host sends a reset request to the
controller. This request is processed by the vhci_send_frame() function.
However, this request is send by a different thread, so it might happen
that this HCI request will be received before the vendor response is
queued in the read queue. This results in the HCI vendor response and
HCI reset request inversion in the read queue which leads to improper
behavior of btvirt:
> dmesg
[1754256.640122] Bluetooth: MGMT ver 1.22
[1754263.023806] Bluetooth: MGMT ver 1.22
[1754265.043775] Bluetooth: hci1: Opcode 0x c03 failed: -110
In order to synchronize vhci two-step open/setup process with virtual
HCI initialization, this patch adds internal lock when queuing data in
the vhci_send_frame() function.
Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a05334d7f ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with hardware interrupts being disabled.
So replace kfree_skb() with dev_kfree_skb_irq() under
spin_lock_irqsave(). Compile tested only.
Fixes: baac6276c0 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8b5aed313 ]
in nokia_bluetooth_serdev_probe(), check the return value of
clk_prepare_enable() and return the error code if
clk_prepare_enable() returns an unexpected value.
Fixes: 7bb318680e ("Bluetooth: add nokia driver")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 73f7b171b7 upstream.
In btsdio_probe, the data->work is bound with btsdio_work. It will be
started in btsdio_send_frame.
If the btsdio_remove runs with a unfinished work, there may be a race
condition that hdev is freed but used in btsdio_work. Fix it by
canceling the work before do cleanup in btsdio_remove.
Fixes: CVE-2023-1989
Fixes: ddbaf13e36 ("[Bluetooth] Add generic driver for Bluetooth SDIO devices")
Cc: stable@vger.kernel.org
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
[ Denis: Added CVE-2023-1989 and fixes tags. ]
Signed-off-by: Denis Efremov (Oracle) <efremov@linux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fa01eba11f ]
Adding the device ID from the Asus Ally gets the bluetooth working
on the device.
Signed-off-by: Matthew Anderson <ruinairas1992@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 47c5d829a3 upstream.
Since commit 3e4be65eb8 ("Bluetooth: hci_qca: Add poweroff support
during hci down for wcn3990"), the setup callback which registers the
debugfs interface can be called multiple times.
This specifically leads to the following error when powering on the
controller:
debugfs: Directory 'ibs' with parent 'hci0' already present!
Add a driver flag to avoid trying to register the debugfs interface more
than once.
Fixes: 3e4be65eb8 ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990")
Cc: stable@vger.kernel.org # 4.20
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
