commit 9149c9b0c7 upstream.
This fix addresses STAR 9001285599, which only affects DWC_usb3 version
3.20a. The timer value for PM_LC_TIMER in DWC_usb3 3.20a for the Link
ECN changes is incorrect. If the PM TIMER ECN is enabled via GUCTL2[19],
the link compliance test (TD7.21) may fail. If the ECN is not enabled
(GUCTL2[19] = 0), the controller will use the old timer value (5us),
which is still acceptable for the link compliance test. Therefore, clear
GUCTL2[19] to pass the USB link compliance test: TD 7.21.
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240829094502.26502-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee0d382feb ]
We should verify the bound of the array to assure that host
may not manipulate the index to point past endpoint array.
Found by static analysis.
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240625022306.2568122-1-make24@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d32685a25 ]
Set the host status byte when a data completion error is encountered
otherwise the upper layer may end up using the invalid zero'ed data.
The following output was observed from scsi/sd.c prior to this fix.
[ 11.872824] sd 0:0:0:1: [sdf] tag#9 data cmplt err -75 uas-tag 1 inflight:
[ 11.872826] sd 0:0:0:1: [sdf] tag#9 CDB: Read capacity(16) 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00
[ 11.872830] sd 0:0:0:1: [sdf] Sector size 0 reported, assuming 512.
Signed-off-by: Shantanu Goel <sgoel01@yahoo.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/87msnx4ec6.fsf@yahoo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99516f76db ]
ucsi_register_altmode checks IS_ERR for the alt pointer and treats
NULL as valid. When CONFIG_TYPEC_DP_ALTMODE is not enabled,
ucsi_register_displayport returns NULL which causes a NULL pointer
dereference in trace. Rather than return NULL, call
typec_port_register_altmode to register DisplayPort alternate mode
as a non-controllable mode when CONFIG_TYPEC_DP_ALTMODE is not enabled.
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240510201244.2968152-2-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b6b386f9a ]
Skip submitting URBs, when identical requests were already sent in
tweak_special_requests(). Instead call the completion handler directly
to return the result of the URB.
Even though submitting those requests twice should be harmless, there
are USB devices that react poorly to some duplicated requests.
One example is the ChipIdea controller implementation in U-Boot: The
second SET_CONFIGURATION request makes U-Boot disable and re-enable all
endpoints. Re-enabling an endpoint in the ChipIdea controller, however,
was broken until U-Boot commit b272c8792502 ("usb: ci: Fix gadget
reinit").
Signed-off-by: Simon Holesch <simon@holesch.de>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Reviewed-by: Hongren Zheng <i@zenithal.me>
Tested-by: Hongren Zheng <i@zenithal.me>
Link: https://lore.kernel.org/r/20240519141922.171460-1-simon@holesch.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 740f2e2791 upstream.
Stop Endpoint command on LINK TRB with TC bit set to 1 causes that
internal cycle bit can have incorrect state after command complete.
In consequence empty transfer ring can be incorrectly detected
when EP is resumed.
NOP TRB before LINK TRB avoid such scenario. Stop Endpoint command
is then on NOP TRB and internal cycle bit is not changed and have
correct value.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB953878279F375CCCE6C6F40FDD8E2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a8839bbb8 upstream.
Device attribute group @usb3_hardware_lpm_attr_group is merged by
add_power_attributes(), but it is not unmerged explicitly, fixed by
unmerging it in remove_power_attributes().
Fixes: 655fe4effe ("usbcore: add sysfs support to xHCI usb3 hardware LPM")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20240820-sysfs_fix-v2-1-a9441487077e@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddfcfeba89 upstream.
The probe function never performs any paltform device allocation, thus
error path "undo_platform_dev_alloc" is entirely bogus. It drops the
reference count from the platform device being probed. If error path is
triggered, this will lead to unbalanced device reference counts and
premature release of device resources, thus possible use-after-free when
releasing remaining devm-managed resources.
Fixes: f83fca0707 ("usb: dwc3: add ST dwc3 glue layer to manage dwc3 HC")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20240814093957.37940-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14e497183d upstream.
This commit addresses an issue where the USB core could access an
invalid event buffer address during runtime suspend, potentially causing
SMMU faults and other memory issues in Exynos platforms. The problem
arises from the following sequence.
1. In dwc3_gadget_suspend, there is a chance of a timeout when
moving the USB core to the halt state after clearing the
run/stop bit by software.
2. In dwc3_core_exit, the event buffer is cleared regardless of
the USB core's status, which may lead to an SMMU faults and
other memory issues. if the USB core tries to access the event
buffer address.
To prevent this hardware quirk on Exynos platforms, this commit ensures
that the event buffer address is not cleared by software when the USB
core is active during runtime suspend by checking its status before
clearing the buffer address.
Cc: stable <stable@kernel.org>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240815064836.1491-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b00583eca upstream.
USB_DEVICE(0x1901, 0x0006) may send data before cdc_acm is ready, which
may be misinterpreted in the default N_TTY line discipline.
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Acked-by: Oliver Neuku <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240814072905.2501-1-ian.ray@gehealthcare.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit cfcd544a99 ("usb: typec: tcpm: unregister existing source
caps before re-registration"), quilt, and git, applied the diff to the
incorrect function, which would cause bad problems if exercised in a
device with these capabilities.
Fix this all up (including the follow-up fix in commit 4053696594
("usb: typec: tcpm: fix use-after-free case in
tcpm_register_source_caps") to be in the correct function.
Fixes: 4053696594 ("usb: typec: tcpm: fix use-after-free case in tcpm_register_source_caps")
Fixes: cfcd544a99 ("usb: typec: tcpm: unregister existing source caps before re-registration")
Reported-by: Charles Yo <charlesyo@google.com>
Cc: Kyle Tso <kyletso@google.com>
Cc: Amit Sunil Dhamne <amitsd@google.com>
Cc: Ondrej Jirman <megi@xff.cz>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dddc00f255 upstream.
This reverts commit 52a39f2cf6.
Based on review comments, it was applied too soon and needs more work.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20231005081716.GA13853@pendragon.ideasonboard.com
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 89d7f96299 ]
On some SoC's like SA8295P where the tertiary controller is host-only
capable, GEVTADDRHI/LO, GEVTSIZ, GEVTCOUNT registers are not accessible.
Trying to access them leads to a crash.
For DRD/Peripheral supported controllers, event buffer setup is done
again in gadget_pullup. Skip setup or cleanup of event buffers if
controller is host-only capable.
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-4-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87850f6cc2 ]
This fixes a W=1 warning about sprintf writing up to 16 bytes into a
buffer of size 14. There is no practical relevance because there are not
more than 32 endpoints.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/6754df25c56aae04f8110594fad2cd2452b1862a.1708709120.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52a39f2cf6 ]
The uvc_video_enable function of the uvc-gadget driver is dequeing and
immediately deallocs all requests on its disable codepath. This is not
save since the dequeue function is async and does not ensure that the
requests are left unlinked in the controller driver.
By adding the ep_free_request into the completion path of the requests
we ensure that the request will be properly deallocated.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230911140530.2995138-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit af8e119f52 upstream.
re-enumerating full-speed devices after a failed address device command
can trigger a NULL pointer dereference.
Full-speed devices may need to reconfigure the endpoint 0 Max Packet Size
value during enumeration. Usb core calls usb_ep0_reinit() in this case,
which ends up calling xhci_configure_endpoint().
On Panther point xHC the xhci_configure_endpoint() function will
additionally check and reserve bandwidth in software. Other hosts do
this in hardware
If xHC address device command fails then a new xhci_virt_device structure
is allocated as part of re-enabling the slot, but the bandwidth table
pointers are not set up properly here.
This triggers the NULL pointer dereference the next time usb_ep0_reinit()
is called and xhci_configure_endpoint() tries to check and reserve
bandwidth
[46710.713538] usb 3-1: new full-speed USB device number 5 using xhci_hcd
[46710.713699] usb 3-1: Device not responding to setup address.
[46710.917684] usb 3-1: Device not responding to setup address.
[46711.125536] usb 3-1: device not accepting address 5, error -71
[46711.125594] BUG: kernel NULL pointer dereference, address: 0000000000000008
[46711.125600] #PF: supervisor read access in kernel mode
[46711.125603] #PF: error_code(0x0000) - not-present page
[46711.125606] PGD 0 P4D 0
[46711.125610] Oops: Oops: 0000 [#1] PREEMPT SMP PTI
[46711.125615] CPU: 1 PID: 25760 Comm: kworker/1:2 Not tainted 6.10.3_2 #1
[46711.125620] Hardware name: Gigabyte Technology Co., Ltd.
[46711.125623] Workqueue: usb_hub_wq hub_event [usbcore]
[46711.125668] RIP: 0010:xhci_reserve_bandwidth (drivers/usb/host/xhci.c
Fix this by making sure bandwidth table pointers are set up correctly
after a failed address device command, and additionally by avoiding
checking for bandwidth in cases like this where no actual endpoints are
added or removed, i.e. only context for default control endpoint 0 is
evaluated.
Reported-by: Karel Balej <balejk@matfyz.cz>
Closes: https://lore.kernel.org/linux-usb/D3CKQQAETH47.1MUO22RTCH2O3@matfyz.cz/
Cc: stable@vger.kernel.org
Fixes: 651aaf36a7 ("usb: xhci: Handle USB transaction error on address command")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240815141117.2702314-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a444bea37 upstream.
Upstream commit aba3a8d01d ("usb: gadget: u_serial: add suspend
resume callbacks") added started_delayed flag, so that new ports
which are opened after USB suspend can start IO while resuming.
But if the port was already opened, and gadget suspend kicks in
afterwards, start_delayed will never be set. This causes resume
to bail out before calling gs_start_io(). Fix this by setting
start_delayed during suspend.
Fixes: aba3a8d01d ("usb: gadget: u_serial: add suspend resume callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240730125754.576326-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 973a578916 upstream.
Make sure the descriptor has been set before looking at maxpacket.
This fixes a null pointer panic in this case.
This may happen if the gadget doesn't properly set up the endpoint
for the current speed, or the gadget descriptors are malformed and
the descriptor for the speed/endpoint are not found.
No current gadget driver is known to have this problem, but this
may cause a hard-to-find bug during development of new gadgets.
Fixes: 54f83b8c8e ("USB: gadget: Reject endpoints with 0 maxpacket value")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Wulff <crwulff@gmail.com>
Link: https://lore.kernel.org/r/20240725010419.314430-2-crwulff@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00af4f3dda upstream.
This driver is intended as a "client" end of the console connection.
When connected to a host it's supposed to receive debug logs, and
possibly allow to interact with whatever debug console is available
there. Feeding messages back, depending on a configuration may cause log
messages be executed as shell commands (which can be really bad if one
is unlucky, imagine a log message like "prevented running `rm -rf
/home`"). In case of Xen, it exposes sysrq-like debug interface, and
feeding it its own logs will pretty quickly hit 'R' for "instant
reboot".
Contrary to a classic serial console, the USB one cannot be configured
ahead of time, as the device shows up only when target OS is up. And at
the time device is opened to execute relevant ioctl, it's already too
late, especially when logs start flowing shortly after device is
initialized.
Avoid the issue by changing default to no echo for this type of devices.
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
[ johan: amend summary; disable also ECHONL ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afdcfd3d6f upstream.
At a few places the driver carries stale pointers
to references that can still be used. Make sure that does not happen.
This strictly speaking closes ZDI-CAN-22273, though there may be
similar races in the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240709113851.14691-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79989bd4ab upstream.
Usb device connect may not be detected after runtime resume if
xHC is reset during resume.
In runtime resume cases xhci_resume() will only resume roothubs if there
are pending port events. If the xHC host is reset during runtime resume
due to a Save/Restore Error (SRE) then these pending port events won't be
detected as PORTSC change bits are not immediately set by host after reset.
Unconditionally resume roothubs if xHC is reset during resume to ensure
device connections are detected.
Also return early with error code if starting xHC fails after reset.
Issue was debugged and a similar solution suggested by Remi Pommarel.
Using this instead as it simplifies future refactoring.
Reported-by: Remi Pommarel <repk@triplefau.lt>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218987
Suggested-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240627145523.1453155-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a368ecde8a upstream.
Syzbot has identified a bug in usbcore (see the Closes: tag below)
caused by our assumption that the reserved bits in an endpoint
descriptor's bEndpointAddress field will always be 0. As a result of
the bug, the endpoint_is_duplicate() routine in config.c (and possibly
other routines as well) may believe that two descriptors are for
distinct endpoints, even though they have the same direction and
endpoint number. This can lead to confusion, including the bug
identified by syzbot (two descriptors with matching endpoint numbers
and directions, where one was interrupt and the other was bulk).
To fix the bug, we will clear the reserved bits in bEndpointAddress
when we parse the descriptor. (Note that both the USB-2.0 and USB-3.1
specs say these bits are "Reserved, reset to zero".) This requires us
to make a copy of the descriptor earlier in usb_parse_endpoint() and
use the copy instead of the original when checking for duplicates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+8693a0bb9c10b554272a@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/0000000000003d868e061bc0f554@google.com/
Fixes: 0a8fd13462 ("USB: fix problems with duplicate endpoint addresses")
CC: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/205a5edc-7fef-4159-b64a-80374b6b101a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d3c721e68 upstream.
Userspace provided string 's' could trivially have the length zero. Left
unchecked this will firstly result in an OOB read in the form
`if (str[0 - 1] == '\n') followed closely by an OOB write in the form
`str[0 - 1] = '\0'`.
There is already a validating check to catch strings that are too long.
Let's supply an additional check for invalid strings that are too short.
Signed-off-by: Lee Jones <lee@kernel.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240705074339.633717-1-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3859e85de3 upstream.
START BP-850K is a dot matrix printer that crashes when
it receives a Set-Interface request and needs USB_QUIRK_NO_SET_INTF
to work properly.
Cc: stable <stable@kernel.org>
Signed-off-by: jinxiaobo <jinxiaobo@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://lore.kernel.org/r/202E4B2BD0F0FEA4+20240702154408.631201-1-wangyuli@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c15a688e49 upstream.
Since commit c49cfa9170 ("USB: serial: use generic method if no
alternative is provided in usb serial layer"), USB serial core calls the
generic resume implementation when the driver has not provided one.
This can trigger a crash on resume with mos7840 since support for
multiple read URBs was added back in 2011. Specifically, both port read
URBs are now submitted on resume for open ports, but the context pointer
of the second URB is left set to the core rather than mos7840 port
structure.
Fix this by implementing dedicated suspend and resume functions for
mos7840.
Tested with Delock 87414 USB 2.0 to 4x serial adapter.
Signed-off-by: Dmitry Smirnov <d.smirnov@inbox.lv>
[ johan: analyse crash and rewrite commit message; set busy flag on
resume; drop bulk-in check; drop unnecessary usb_kill_urb() ]
Fixes: d83b405383 ("USB: serial: add support for multiple read urbs")
Cc: stable@vger.kernel.org # 3.3
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 948554f1bb which is
commit 66cb618bf0 upstream.
In backporting it to stable kernels, it causes a severe regression on
many systems, so revert it for now.
Reported-by: Tim Lewis <elatllat@gmail.com>
Link: https://lore.kernel.org/r/CA+3zgmvct7BWib9A7O1ykUf=0nZpdbdpXBdPWOCqfPuyCT3fug@mail.gmail.com
Reported-by: <matthias@bodenbinder.de>
Link: https://lore.kernel.org/r/bug-219039-208809@https.bugzilla.kernel.org/
Cc: Niklas Neronin <niklas.neronin@linux.intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Michał Pecio <michal.pecio@gmail.com>
Cc: <ZeroBeat@gmx.de>
Cc: Salvatore Bonaccorso <carnil@debian.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 66cb618bf0 ]
Some transfer events don't always point to a TRB, and consequently don't
have a endpoint ring. In these cases, function handle_tx_event() should
not proceed, because if 'ep->skip' is set, the pointer to the endpoint
ring is used.
To prevent a potential failure and make the code logical, return after
checking the completion code for a Transfer event without TRBs.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8e1ec117ef upstream.
Sometimes errors are seen, when doing DR swap, like:
[ 24.672481] ucsi-stm32g0-i2c 0-0035: UCSI_GET_PDOS failed (-5)
[ 24.720188] ucsi-stm32g0-i2c 0-0035: ucsi_handle_connector_change:
GET_CONNECTOR_STATUS failed (-5)
There may be some race, which lead to read CCI, before the command complete
flag is set, hence returning -EIO. Similar fix has been done also in
ucsi_acpi [1].
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
To fix this add the ACK_PENDING bit for ucsi_stm32g0 and only complete
commands if the completion bit matches.
[1] https://lore.kernel.org/lkml/20240121204123.275441-3-lk@c--e.de/
Fixes: 72849d4fce ("usb: typec: ucsi: stm32g0: add support for stm32g0 controller")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/stable/20240612124656.2305603-1-fabrice.gasnier%40foss.st.com
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240612124656.2305603-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dba7567c2f upstream.
In the aspeed UDC setup, we configure the UDC hardware with the assigned
USB device address.
However, we have an off-by-one in the bitmask, so we're only setting the
lower 6 bits of the address (USB addresses being 7 bits, and the
hardware bitmask being bits 0:6).
This means that device enumeration fails if the assigned address is
greater than 64:
[ 344.607255] usb 1-1: new high-speed USB device number 63 using ehci-platform
[ 344.808459] usb 1-1: New USB device found, idVendor=cc00, idProduct=cc00, bcdDevice= 6.10
[ 344.817684] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 344.825671] usb 1-1: Product: Test device
[ 344.831075] usb 1-1: Manufacturer: Test vendor
[ 344.836335] usb 1-1: SerialNumber: 00
[ 349.917181] usb 1-1: USB disconnect, device number 63
[ 352.036775] usb 1-1: new high-speed USB device number 64 using ehci-platform
[ 352.249432] usb 1-1: device descriptor read/all, error -71
[ 352.696740] usb 1-1: new high-speed USB device number 65 using ehci-platform
[ 352.909431] usb 1-1: device descriptor read/all, error -71
Use the correct mask of 0x7f (rather than 0x3f), and generate this
through the GENMASK macro, so we have numbers that correspond exactly
to the hardware register definition.
Fixes: 055276c132 ("usb: gadget: add Aspeed ast2600 udc driver")
Cc: stable@vger.kernel.org
Reviewed-by: Neal Liu <neal_liu@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240613-aspeed-udc-v2-1-29501ce9cb7a@codeconstruct.com.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7838de15bb upstream.
When config CONFIG_USB_DWC3_DUAL_ROLE is selected, and trigger system
to enter suspend status with below command:
echo mem > /sys/power/state
There will be a deadlock issue occurring. Detailed invoking path as
below:
dwc3_suspend_common()
spin_lock_irqsave(&dwc->lock, flags); <-- 1st
dwc3_gadget_suspend(dwc);
dwc3_gadget_soft_disconnect(dwc);
spin_lock_irqsave(&dwc->lock, flags); <-- 2nd
This issue is exposed by commit c7ebd8149e ("usb: dwc3: gadget: Fix
NULL pointer dereference in dwc3_gadget_suspend") that removes the code
of checking whether dwc->gadget_driver is NULL or not. It causes the
following code is executed and deadlock occurs when trying to get the
spinlock. In fact, the root cause is the commit 5265397f9442("usb: dwc3:
Remove DWC3 locking during gadget suspend/resume") that forgot to remove
the lock of otg mode. So, remove the redundant lock of otg mode during
gadget suspend/resume.
Fixes: 5265397f94 ("usb: dwc3: Remove DWC3 locking during gadget suspend/resume")
Cc: Xu Yang <xu.yang_2@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240618031918.2585799-1-Meng.Li@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2eabb655a9 upstream.
Syzbot is still reporting quite an old issue [1] that occurs due to
incomplete checking of present usb endpoints. As such, wrong
endpoints types may be used at urb sumbitting stage which in turn
triggers a warning in usb_submit_urb().
Fix the issue by verifying that required endpoint types are present
for both in and out endpoints, taking into account cmd endpoint type.
Unfortunately, this patch has not been tested on real hardware.
[1] Syzbot report:
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 0 PID: 8667 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 0 PID: 8667 Comm: kworker/0:4 Not tainted 5.14.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
...
Call Trace:
cxacru_cm+0x3c0/0x8e0 drivers/usb/atm/cxacru.c:649
cxacru_card_status+0x22/0xd0 drivers/usb/atm/cxacru.c:760
cxacru_bind+0x7ac/0x11a0 drivers/usb/atm/cxacru.c:1209
usbatm_usb_probe+0x321/0x1ae0 drivers/usb/atm/usbatm.c:1055
cxacru_usb_probe+0xdf/0x1e0 drivers/usb/atm/cxacru.c:1363
usb_probe_interface+0x315/0x7f0 drivers/usb/core/driver.c:396
call_driver_probe drivers/base/dd.c:517 [inline]
really_probe+0x23c/0xcd0 drivers/base/dd.c:595
__driver_probe_device+0x338/0x4d0 drivers/base/dd.c:747
driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:777
__device_attach_driver+0x20b/0x2f0 drivers/base/dd.c:894
bus_for_each_drv+0x15f/0x1e0 drivers/base/bus.c:427
__device_attach+0x228/0x4a0 drivers/base/dd.c:965
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:487
device_add+0xc2f/0x2180 drivers/base/core.c:3354
usb_set_configuration+0x113a/0x1910 drivers/usb/core/message.c:2170
usb_generic_driver_probe+0xba/0x100 drivers/usb/core/generic.c:238
usb_probe_device+0xd9/0x2c0 drivers/usb/core/driver.c:293
Reported-and-tested-by: syzbot+00c18ee8497dd3be6ade@syzkaller.appspotmail.com
Fixes: 902ffc3c70 ("USB: cxacru: Use a bulk/int URB to access the command endpoint")
Cc: stable <stable@kernel.org>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20240609131546.3932-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e587a7633d upstream.
printer_read() and printer_write() guard against the race
against disable() by checking the dev->interface flag,
which in turn is guarded by a spinlock.
These functions, however, drop the lock on multiple occasions.
This means that the test has to be redone after reacquiring
the lock and before doing IO.
Add the tests.
This also addresses CVE-2024-25741
Fixes: 7f2ca14d2f ("usb: gadget: function: printer: Interface is disabled and returns error")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240620114039.5767-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd80731e5e upstream.
We need to treat super speed plus as super speed, not the default,
which is full speed.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240620093800.28901-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8bdf8a42bc ]
It is possible that also the GET_ERROR command fails. If
that happens, the command completion still needs to be
acknowledged. Otherwise the interface will be stuck until
it's reset.
Reported-by: Ammy Yi <ammy.yi@intel.com>
Fixes: bdc62f2bae ("usb: typec: ucsi: Simplified registration and I/O API")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240531104653.1303519-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de52aca4d9 ]
Some PPM implementation do not like UCSI_ACK_CONNECTOR_CHANGE
without UCSI_ACK_COMMAND_COMPLETE. Moreover, doing this is racy
as it requires sending two UCSI_ACK_CC_CI commands in a row and
the second one will be started with UCSI_CCI_ACK_COMPLETE already
set in CCI.
Bundle the UCSI_ACK_CONNECTOR_CHANGE with the UCSI_ACK_COMMAND_COMPLETE
for the UCSI_GET_CONNECTOR_STATUS command that is sent while
handling a connector change event.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240327224554.1772525-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8bdf8a42bc ("usb: typec: ucsi: Ack also failed Get Error commands")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 920e7522e3 ]
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
Note that the upper limit of ida_simple_get() is exclusive, but the one of
ida_alloc_max() is inclusive. So a -1 has been added when needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/7cd361e2b377a5373968fa7deee4169229992a1e.1713107386.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fb782b5d5 ]
The Lenovo Yoga Tablet 2 Pro 1380 model is the exception to the rule that
devices which use the Crystal Cove PMIC without using ACPI for battery and
AC power_supply class support use the USB-phy for charger detection.
Unlike the Lenovo Yoga Tablet 2 830 / 1050 models this model has an extra
LC824206XA Micro USB switch which does the charger detection.
Add a DMI quirk to not set the "linux,phy_charger_detect" property on
the 1380 model. This quirk matches on the BIOS version to differentiate
the 1380 model from the 830 and 1050 models which otherwise have
the same DMI strings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240406140127.17885-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3295f1b866 ]
The incompatible device in my possession has a sticker that says
"F5U002 Rev 2" and "P80453-B", and lsusb identifies it as
"050d:0002 Belkin Components IEEE-1284 Controller". There is a bug
report from 2007 from Michael Trausch who was seeing the exact same
errors that I saw in 2024 trying to use this cable.
Link: https://lore.kernel.org/all/46DE5830.9060401@trausch.us/
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-5-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
