commit f956052e00 upstream.
font.data may not initialize all memory spaces depending on the implementation
of vc->vc_sw->con_font_get. This may cause info-leak, so to prevent this, it
is safest to modify it to initialize the allocated memory space to 0, and it
generally does not affect the overall performance of the system.
Cc: stable@vger.kernel.org
Reported-by: syzbot+955da2d57931604ee691@syzkaller.appspotmail.com
Fixes: 05e2600cb0 ("VT: Bump font size limitation to 64x128 pixels")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Link: https://lore.kernel.org/r/20241010174619.59662-1-aha310510@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 602babaa84 ]
Commit af224ca2df (serial: core: Prevent unsafe uart port access, part
3) added few uport == NULL checks. It added one to uart_shutdown(), so
the commit assumes, uport can be NULL in there. But right after that
protection, there is an unprotected "uart_port_dtr_rts(uport, false);"
call. That is invoked only if HUPCL is set, so I assume that is the
reason why we do not see lots of these reports.
Or it cannot be NULL at this point at all for some reason :P.
Until the above is investigated, stay on the safe side and move this
dereference to the if too.
I got this inconsistency from Coverity under CID 1585130. Thanks.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240805102046.307511-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Adapted over commit 5701cb8bf5 ("tty: Call ->dtr_rts() parameter
active consistently") not in the tree]
Signed-off-by: Tomas Krcka <krckatom@amazon.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40d7903386 ]
When sending data using DMA at high baudrate (4 Mbdps in local test case) to
a device with small RX buffer which keeps asserting RTS after every received
byte, it is possible that the iMX UART driver would not recognize the falling
edge of RTS input signal and get stuck, unable to transmit any more data.
This condition happens when the following sequence of events occur:
- imx_uart_mctrl_check() is called at some point and takes a snapshot of UART
control signal status into sport->old_status using imx_uart_get_hwmctrl().
The RTSS/TIOCM_CTS bit is of interest here (*).
- DMA transfer occurs, the remote device asserts RTS signal after each byte.
The i.MX UART driver recognizes each such RTS signal change, raises an
interrupt with USR1 register RTSD bit set, which leads to invocation of
__imx_uart_rtsint(), which calls uart_handle_cts_change().
- If the RTS signal is deasserted, uart_handle_cts_change() clears
port->hw_stopped and unblocks the port for further data transfers.
- If the RTS is asserted, uart_handle_cts_change() sets port->hw_stopped
and blocks the port for further data transfers. This may occur as the
last interrupt of a transfer, which means port->hw_stopped remains set
and the port remains blocked (**).
- Any further data transfer attempts will trigger imx_uart_mctrl_check(),
which will read current status of UART control signals by calling
imx_uart_get_hwmctrl() (***) and compare it with sport->old_status .
- If current status differs from sport->old_status for RTS signal,
uart_handle_cts_change() is called and possibly unblocks the port
by clearing port->hw_stopped .
- If current status does not differ from sport->old_status for RTS
signal, no action occurs. This may occur in case prior snapshot (*)
was taken before any transfer so the RTS is deasserted, current
snapshot (***) was taken after a transfer and therefore RTS is
deasserted again, which means current status and sport->old_status
are identical. In case (**) triggered when RTS got asserted, and
made port->hw_stopped set, the port->hw_stopped will remain set
because no change on RTS line is recognized by this driver and
uart_handle_cts_change() is not called from here to unblock the
port->hw_stopped.
Update sport->old_status in __imx_uart_rtsint() accordingly to make
imx_uart_mctrl_check() detect such RTS change. Note that TIOCM_CAR
and TIOCM_RI bits in sport->old_status do not suffer from this problem.
Fixes: ceca629e0b ("[ARM] 2971/1: i.MX uart handle rts irq")
Cc: stable <stable@kernel.org>
Reviewed-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20241002184133.19427-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 968d64578e ]
Convert uart_handle_cts_change() to bool which is more appropriate
than unsigned int.
Rename status to active to better describe what the parameter means.
While at it, make the comment about the active parameter easier to
parse.
Cleanup callsites from operations that are not necessary with bool.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-10-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 40d7903386 ("serial: imx: Update mctrl old_status on RTSD interrupt")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0388a152fc ]
Convert status parameter for ->dcd_change() and
uart_handle_dcd_change() to bool which matches to how the parameter is
used.
Rename status to active to better describe what the parameter means.
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 40d7903386 ("serial: imx: Update mctrl old_status on RTSD interrupt")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f16dd10ba3 upstream.
The write to RP2_GLOBAL_CMD followed by an immediate read of
RP2_GLOBAL_CMD in rp2_reset_asic() is intented to flush out the write,
however by then the device is already in reset and cannot respond to a
memory cycle access.
On platforms such as the Raspberry Pi 4 and others using the
pcie-brcmstb.c driver, any memory access to a device that cannot respond
is met with a fatal system error, rather than being substituted with all
1s as is usually the case on PC platforms.
Swapping the delay and the read ensures that the device has finished
resetting before we attempt to read from it.
Fixes: 7d9f49afa4 ("serial: rp2: New driver for Comtrol RocketPort 2 cards")
Cc: stable <stable@kernel.org>
Suggested-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240906225435.707837-1-florian.fainelli@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9f6613b16 upstream.
In RS485 mode, the RTS pin is driven high by hardware when the transmitter
is operating. This behaviour cannot be changed. This means that the driver
should claim that it supports SER_RS485_RTS_ON_SEND and not
SER_RS485_RTS_AFTER_SEND.
Otherwise, when configuring the port with the SER_RS485_RTS_ON_SEND, one
get the following warning:
kern.warning kernel: atmel_usart_serial atmel_usart_serial.2.auto:
ttyS1 (1): invalid RTS setting, using RTS_AFTER_SEND instead
which is contradictory with what's really happening.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Cc: stable <stable@kernel.org>
Tested-by: Alexander Dahl <ada@thorsis.com>
Fixes: af47c491e3 ("serial: atmel: Fill in rs485_supported")
Link: https://lore.kernel.org/r/20240808060637.19886-1-othacehe@gnu.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6eabce6608 upstream.
Calling ioctl TIOCSSERIAL with an invalid baud_base can
result in uartclk being zero, which will result in a
divide by zero error in uart_get_divisor(). The check for
uartclk being zero in uart_set_info() needs to be done
before other settings are made as subsequent calls to
ioctl TIOCSSERIAL for the same port would be impacted if
the uartclk check was done where uartclk gets set.
Oops: divide error: 0000 PREEMPT SMP KASAN PTI
RIP: 0010:uart_get_divisor (drivers/tty/serial/serial_core.c:580)
Call Trace:
<TASK>
serial8250_get_divisor (drivers/tty/serial/8250/8250_port.c:2576
drivers/tty/serial/8250/8250_port.c:2589)
serial8250_do_set_termios (drivers/tty/serial/8250/8250_port.c:502
drivers/tty/serial/8250/8250_port.c:2741)
serial8250_set_termios (drivers/tty/serial/8250/8250_port.c:2862)
uart_change_line_settings (./include/linux/spinlock.h:376
./include/linux/serial_core.h:608 drivers/tty/serial/serial_core.c:222)
uart_port_startup (drivers/tty/serial/serial_core.c:342)
uart_startup (drivers/tty/serial/serial_core.c:368)
uart_set_info (drivers/tty/serial/serial_core.c:1034)
uart_set_info_user (drivers/tty/serial/serial_core.c:1059)
tty_set_serial (drivers/tty/tty_io.c:2637)
tty_ioctl (drivers/tty/tty_io.c:2647 drivers/tty/tty_io.c:2791)
__x64_sys_ioctl (fs/ioctl.c:52 fs/ioctl.c:907
fs/ioctl.c:893 fs/ioctl.c:893)
do_syscall_64 (arch/x86/entry/common.c:52
(discriminator 1) arch/x86/entry/common.c:83 (discriminator 1))
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Reported-by: syzkaller <syzkaller@googlegroups.com>
Cc: stable@vger.kernel.org
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Rule: add
Link: https://lore.kernel.org/stable/1721148848-9784-1-git-send-email-george.kennedy%40oracle.com
Link: https://lore.kernel.org/r/1721219078-3209-1-git-send-email-george.kennedy@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a3d8728ab0 ]
At the default TX trigger level of 2 in non-DMA mode (meaning that an
interrupt is generated when less than 2 characters are left in the
FIFO), we have observed frequent buffer underruns at 115200 Baud on an
i.MX8M Nano. This can cause communication issues if the receiving side
expects a continuous transfer.
Increasing the level to 8 makes the UART trigger an interrupt earlier,
giving the kernel enough time to refill the FIFO, at the cost of
triggering one interrupt per ~24 instead of ~30 bytes of transmitted
data (as the i.MX UART has a 32 byte FIFO).
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240508133744.35858-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c128a1b052 upstream.
Errata i2310[0] says, Erroneous timeout can be triggered,
if this Erroneous interrupt is not cleared then it may leads
to storm of interrupts.
Commit 9d141c1e61 ("serial: 8250_omap: Implementation of Errata i2310")
which added the workaround but missed ensuring RX FIFO is really empty
before applying the errata workaround as recommended in the errata text.
Fix this by adding back check for UART_OMAP_RX_LVL to be 0 for
workaround to take effect.
[0] https://www.ti.com/lit/pdf/sprz536 page 23
Fixes: 9d141c1e61 ("serial: 8250_omap: Implementation of Errata i2310")
Cc: stable@vger.kernel.org
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Closes: https://lore.kernel.org/all/e96d0c55-0b12-4cbf-9d23-48963543de49@ti.com/
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240625160725.2102194-1-u-kumar1@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9706fc87b4 upstream.
With commit a81dbd0463 ("serial: imx: set receiver level before
starting uart") we set the receiver level to its default value. This
caused a regression when using SDMA, where the receiver level is 9
instead of 8 (default). This change will first check if the receiver
level is zero and only then set it to the default. This still avoids the
interrupt storm when the receiver level is zero.
Fixes: a81dbd0463 ("serial: imx: set receiver level before starting uart")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240703112543.148304-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c92a8bd53 upstream.
Most of the colfires have up to 5 UARTs but MCF54418 has up-to 10 !
Change the maximum value authorized.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@yoseli.org>
Cc: stable <stable@kernel.org>
Fixes: 2545cf6e94 ("m68knommu: allow 4 coldfire serial ports")
Link: https://lore.kernel.org/r/20240620-upstream-uart-v1-1-a9d0d95fb19e@yoseli.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a81dbd0463 upstream.
Set the receiver level to something > 0 before calling imx_uart_start_rx
in rs485_config. This is necessary to avoid an interrupt storm that
might prevent the system from booting. This was seen on an i.MX7 device
when the rs485-rts-active-low property was active in the device tree.
Fixes: 6d215f83e5 ("serial: imx: warn user when using unsupported configuration")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240621153829.183780-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6bd23e0c2b ]
... and use it to limit the virtual terminals to just N_TTY. They are
kind of special, and in particular, the "con_write()" routine violates
the "writes cannot sleep" rule that some ldiscs rely on.
This avoids the
BUG: sleeping function called from invalid context at kernel/printk/printk.c:2659
when N_GSM has been attached to a virtual console, and gsmld_write()
calls con_write() while holding a spinlock, and con_write() then tries
to get the console lock.
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Daniel Starke <daniel.starke@siemens.com>
Reported-by: syzbot <syzbot+dbac96d8e73b61aa559c@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=dbac96d8e73b61aa559c
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20240423163339.59780-1-torvalds@linux-foundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e533e4c62e ]
By waiting at most 1 second for USR2_TXDC to be set, we avoid a potential
deadlock.
In case of the timeout, there is not much we can do, so we simply ignore
the transmitter state and optimistically try to continue.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/919647898c337a46604edcabaf13d42d80c0915d.1712837613.git.esben@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22130dae05 ]
When there's no irq(this can be due to various reasons, for example,
no irq from HW support, or we just want to use poll solution, and so
on), falling back to poll is still better than no support at all.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20230806092056.2467-3-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 87d80bfbd5 ("serial: 8250_dw: Don't use struct dw8250_data outside of 8250_dw")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5208e7ced5 upstream.
The FIFO is 64 bytes, but the FCR is configured to fire the TX interrupt
when the FIFO is half empty (bit 3 = 0). Thus, we should only write 32
bytes when a TX interrupt occurs.
This fixes a problem observed on the PXA168 that dropped a bunch of TX
bytes during large transmissions.
Fixes: ab28f51c77 ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20240519191929.122202-1-doug@schmorgal.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b19ab7ee2c upstream.
When lookahead has "consumed" some characters (la_count > 0),
n_tty_receive_buf_standard() and n_tty_receive_buf_closing() for
characters beyond the la_count are given wrong cp/fp offsets which
leads to duplicating and losing some characters.
If la_count > 0, correct buffer pointers and make count consistent too
(the latter is not strictly necessary to fix the issue but seems more
logical to adjust all variables immediately to keep state consistent).
Reported-by: Vadym Krevs <vkrevs@yahoo.com>
Fixes: 6bb6fa6908 ("tty: Implement lookahead to process XON/XOFF timely")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218834
Tested-by: Vadym Krevs <vkrevs@yahoo.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240514140429.12087-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8492bd91aa ]
When using a high speed clock with a low baud rate, the 4x prescaler is
automatically selected if required. In that case, sc16is7xx_set_baud()
properly configures the chip registers, but returns an incorrect baud
rate by not taking into account the prescaler value. This incorrect baud
rate is then fed to uart_update_timeout().
For example, with an input clock of 80MHz, and a selected baud rate of 50,
sc16is7xx_set_baud() will return 200 instead of 50.
Fix this by first changing the prescaler variable to hold the selected
prescaler value instead of the MCR bitfield. Then properly take into
account the selected prescaler value in the return value computation.
Also add better documentation about the divisor value computation.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240430200431.4102923-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e57cefc44 ]
To better show why the limit is what it is, since we have only 16 bits for
the divisor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-13-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8492bd91aa ("serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aae20f6e34 ]
The to-be-fixed commit removed locking when invalidating the DMA RX
descriptors on shutdown. It overlooked that there is still a rx_timer
running which may still access the protected data. So, re-add the
locking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Closes: https://lore.kernel.org/r/ee6c9e16-9f29-450e-81da-4a8dceaa8fc7@de.bosch.com
Fixes: 2c4ee23530 ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-7-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a8e4ab0c9 ]
Replace incorrect include with the proper one for sched_set_fifo()
declaration.
Fixes: 28d2f209cd ("sched,serial: Convert to sched_set_fifo()")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409154253.3043822-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e60955dbec ]
Sparse is not happy about misuse of bitwise types:
.../max3100.c:194:13: warning: incorrect type in assignment (different base types)
.../max3100.c:194:13: expected unsigned short [addressable] [usertype] etx
.../max3100.c:194:13: got restricted __be16 [usertype]
.../max3100.c:202:15: warning: cast to restricted __be16
Fix this by choosing proper types for the respective variables.
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 712a1fcb38 ]
The removal of the last MAX3100 device triggers the removal of
the driver. However, code doesn't update the respective global
variable and after insmod — rmmod — insmod cycle the kernel
oopses:
max3100 spi-PRP0001:01: max3100_probe: adding port 0
BUG: kernel NULL pointer dereference, address: 0000000000000408
...
RIP: 0010:serial_core_register_port+0xa0/0x840
...
max3100_probe+0x1b6/0x280 [max3100]
spi_probe+0x8d/0xb0
Update the actual state so next time UART driver will be registered
again.
Hugo also noticed, that the error path in the probe also affected
by having the variable set, and not cleared. Instead of clearing it
move the assignment after the successfull uart_register_driver() call.
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240402195306.269276-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77ab53371a ]
uart_handle_cts_change() has to be called with port lock taken,
Since we run it in a separate work, the lock may not be taken at
the time of running. Make sure that it's taken by explicitly doing
that. Without it we got a splat:
WARNING: CPU: 0 PID: 10 at drivers/tty/serial/serial_core.c:3491 uart_handle_cts_change+0xa6/0xb0
...
Workqueue: max3100-0 max3100_work [max3100]
RIP: 0010:uart_handle_cts_change+0xa6/0xb0
...
max3100_handlerx+0xc5/0x110 [max3100]
max3100_work+0x12a/0x340 [max3100]
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4244f830a5 upstream.
When Rx in-band wakeup is enabled, set RTS to true in mtk8250_shutdown()
so the connected device can still send message and trigger IRQ when the
system is suspended.
Fixes: 18c9d4a3c2 ("serial: When UART is suspended, set RTS to false")
Cc: stable <stable@kernel.org>
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Link: https://lore.kernel.org/r/20240424130619.2924456-1-treapking@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 614a19b89c upstream.
There is a scenario when resuming from some power saving states
with no_console_suspend where console output can be generated
before the 8250_bcm7271 driver gets the opportunity to restore
the baud_mux_clk frequency. Since the baud_mux_clk is at its
default frequency at this time the output can be garbled until
the driver gets the opportunity to resume.
Since this is only an issue with console use of the serial port
during that window and the console isn't likely to use baud
rates that require alternate baud_mux_clk frequencies, allow the
driver to select the default_mux_rate if it is accurate enough.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240424222559.1844045-1-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70d7f1427a upstream.
The current implementation uses either gsm0_receive() or gsm1_receive()
depending on whether the user configured the mux in basic or advanced
option mode. Both functions share some state values over the same logical
elements of the frame. However, both frame types differ in their nature.
gsm0_receive() uses non-transparency framing, whereas gsm1_receive() uses
transparency mechanism. Switching between both modes leaves the receive
function in an undefined state when done during frame reception.
Fix this by splitting both states. Add gsm0_receive_state_check_and_fix()
and gsm1_receive_state_check_and_fix() to ensure that gsm->state is reset
after a change of gsm->receive.
Note that gsm->state is only accessed in:
- gsm0_receive()
- gsm1_receive()
- gsm_error()
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20240424054842.7741-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47388e807f upstream.
Assuming the following:
- side A configures the n_gsm in basic option mode
- side B sends the header of a basic option mode frame with data length 1
- side A switches to advanced option mode
- side B sends 2 data bytes which exceeds gsm->len
Reason: gsm->len is not used in advanced option mode.
- side A switches to basic option mode
- side B keeps sending until gsm0_receive() writes past gsm->buf
Reason: Neither gsm->state nor gsm->len have been reset after
reconfiguration.
Fix this by changing gsm->count to gsm->len comparison from equal to less
than. Also add upper limit checks against the constant MAX_MRU in
gsm0_receive() and gsm1_receive() to harden against memory corruption of
gsm->len and gsm->mru.
All other checks remain as we still need to limit the data according to the
user configuration and actual payload size.
Reported-by: j51569436@gmail.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218708
Tested-by: j51569436@gmail.com
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20240424054842.7741-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2aba15ad6 upstream.
Currently, when kdb is compiled with keyboard support, then we will use
schedule_work() to provoke reset of the keyboard status. Unfortunately
schedule_work() gets called from the kgdboc post-debug-exception
handler. That risks deadlock since schedule_work() is not NMI-safe and,
even on platforms where the NMI is not directly used for debugging, the
debug trap can have NMI-like behaviour depending on where breakpoints
are placed.
Fix this by using the irq work system, which is NMI-safe, to defer the
call to schedule_work() to a point when it is safe to call.
Reported-by: Liuye <liu.yeC@h3c.com>
Closes: https://lore.kernel.org/all/20240228025602.3087748-1-liu.yeC@h3c.com/
Cc: stable@vger.kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240424-kgdboc_fix_schedule_work-v2-1-50f5a490aec5@linaro.org
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea2624b5b8 upstream.
When an UART is opened that still has .throttled set from a previous
open, the RX interrupt is enabled but the irq handler doesn't consider
it. This easily results in a stuck irq with the effect to occupy the CPU
in a tight loop.
So reset the throttle state in .startup() to ensure that RX irqs are
handled.
Fixes: d1ec8a2eab ("serial: stm32: update throttle and unthrottle ops for dma mode")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/a784f80d3414f7db723b2ec66efc56e1ad666cbf.1713344161.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13c785323b upstream.
If there is a stuck irq that the handler doesn't address, returning
IRQ_HANDLED unconditionally makes it impossible for the irq core to
detect the problem and disable the irq. So only return IRQ_HANDLED if
an event was handled.
A stuck irq is still problematic, but with this change at least it only
makes the UART nonfunctional instead of occupying the (usually only) CPU
by 100% and so stall the whole machine.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5f92603d0dfd8a5b8014b2b10a902d91e0bb881f.1713344161.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1be3226445 upstream.
The mitigation was intended to stop the irq completely. That may be
better than a hard lock-up but it turns out that you get a crash anyway
if you're using pmac_zilog as a serial console:
ttyPZ0: pmz: rx irq flood !
BUG: spinlock recursion on CPU#0, swapper/0
That's because the pr_err() call in pmz_receive_chars() results in
pmz_console_write() attempting to lock a spinlock already locked in
pmz_interrupt(). With CONFIG_DEBUG_SPINLOCK=y, this produces a fatal
BUG splat. The spinlock in question is the one in struct uart_port.
Even when it's not fatal, the serial port rx function ceases to work.
Also, the iteration limit doesn't play nicely with QEMU, as can be
seen in the bug report linked below.
A web search for other reports of the error message "pmz: rx irq flood"
didn't produce anything. So I don't think this code is needed any more.
Remove it.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@kernel.org
Cc: linux-m68k@lists.linux-m68k.org
Link: https://github.com/vivier/qemu-m68k/issues/44
Link: https://lore.kernel.org/all/1078874617.9746.36.camel@gaston/
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@kernel.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/e853cf2c762f23101cd2ddec0cc0c2be0e72685f.1712568223.git.fthain@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54c4ec5f8c upstream.
The uart_handle_cts_change() function in serial_core expects the caller
to hold uport->lock. For example, I have seen the below kernel splat,
when the Bluetooth driver is loaded on an i.MX28 board.
[ 85.119255] ------------[ cut here ]------------
[ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec
[ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs
[ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1
[ 85.151396] Hardware name: Freescale MXS (Device Tree)
[ 85.156679] Workqueue: hci0 hci_power_on [bluetooth]
(...)
[ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4
[ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210
(...)
Cc: stable@vger.kernel.org
Fixes: 4d90bb147e ("serial: core: Document and assert lock requirements for irq helpers")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240320121530.11348-1-emil.kronborg@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67c3775689 upstream.
Any unprivileged user can attach N_GSM0710 ldisc, but it requires
CAP_NET_ADMIN to create a GSM network anyway.
Require initial namespace CAP_NET_ADMIN to do that.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Link: https://lore.kernel.org/r/20230731185942.279611-1-cascardo@canonical.com
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 672448ccf9 upstream.
When about to transmit the function imx_uart_start_tx is called and in
some RS485 configurations this function will call imx_uart_stop_rx. The
problem is that imx_uart_stop_rx will enable loopback in order to
release the RS485 bus, but when loopback is enabled transmitted data
will just be looped to RX.
This patch fixes the above problem by not enabling loopback when about
to transmit.
This driver now works well when used for RS485 half duplex master
configurations.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable <stable@kernel.org>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20240221115304.509811-1-rickaran@axis.com
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1581dafaf0 upstream.
This is the same issue that was fixed for the VGA text buffer in commit
39cdb68c64 ("vt: fix memory overlapping when deleting chars in the
buffer"). The cure is also the same i.e. replace memcpy() with memmove()
due to the overlaping buffers.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Fixes: 81732c3b2f ("tty vt: Fix line garbage in virtual console on command line edition")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/sn184on2-3p0q-0qrq-0218-895349s4753o@syhkavp.arg
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74cb7e0355 upstream.
If the remote uart device is not connected or not enabled after booting
up, the CTS line is high by default. At this time, if we enable the flow
control when opening the device(for example, using “stty -F /dev/ttyLP4
crtscts” command), there will be a pending idle preamble(first writing 0
and then writing 1 to UARTCTRL_TE will queue an idle preamble) that
cannot be sent out, resulting in the uart port fail to close(waiting for
TX empty), so the user space stty will have to wait for a long time or
forever.
This is an LPUART IP bug(idle preamble has higher priority than CTS),
here add a workaround patch to enable TX CTS after enabling UARTCTRL_TE,
so that the idle preamble does not get stuck due to CTS is deasserted.
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20240305015706.1050769-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 801410b26a ]
During the handoff from earlycon to the real console driver, we have
two separate drivers operating on the same device concurrently. In the
case of the 8250 driver these concurrent accesses cause problems due
to the driver's use of banked registers, controlled by LCR.DLAB. It is
possible for the setup(), config_port(), pm() and set_mctrl() callbacks
to set DLAB, which can cause the earlycon code that intends to access
TX to instead access DLL, leading to missed output and corruption on
the serial line due to unintended modifications to the baud rate.
In particular, for setup() we have:
univ8250_console_setup()
-> serial8250_console_setup()
-> uart_set_options()
-> serial8250_set_termios()
-> serial8250_do_set_termios()
-> serial8250_do_set_divisor()
For config_port() we have:
serial8250_config_port()
-> autoconfig()
For pm() we have:
serial8250_pm()
-> serial8250_do_pm()
-> serial8250_set_sleep()
For set_mctrl() we have (for some devices):
serial8250_set_mctrl()
-> omap8250_set_mctrl()
-> __omap8250_set_mctrl()
To avoid such problems, let's make it so that the console is locked
during pre-registration calls to these callbacks, which will prevent
the earlycon driver from running concurrently.
Remove the partial solution to this problem in the 8250 driver
that locked the console only during autoconfig_irq(), as this would
result in a deadlock with the new approach. The console continues
to be locked during autoconfig_irq() because it can only be called
through uart_configure_port().
Although this patch introduces more locking than strictly necessary
(and in particular it also locks during the call to rs485_config()
which is not affected by this issue as far as I can tell), it follows
the principle that it is the responsibility of the generic console
code to manage the earlycon handoff by ensuring that earlycon and real
console driver code cannot run concurrently, and not the individual
drivers.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://linux-review.googlesource.com/id/I7cf8124dcebf8618e6b2ee543fa5b25532de55d8
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240304214350.501253-1-pcc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d27056c24 ]
When trying to instantiate a max14830 device from userspace:
echo max14830 0x60 > /sys/bus/i2c/devices/i2c-2/new_device
we get the following error:
Unable to handle kernel NULL pointer dereference at virtual address...
...
Call trace:
max310x_i2c_probe+0x48/0x170 [max310x]
i2c_device_probe+0x150/0x2a0
...
Add check for validity of devtype to prevent the error, and abort probe
with a meaningful error message.
Fixes: 2e1f2d9a9b ("serial: max310x: implement I2C support")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73b5a5c00b ]
It seems a copy&paste mistake that suspend callback removes the GPIO
device. There is no counterpart of this action, means once suspended
there is no more GPIO device available untile full unbind-bind cycle
is performed. Remove suspicious GPIO device removal in suspend.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240219150627.2101198-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 314c2b3992 ]
The core expects for tx_empty() either TIOCSER_TEMT when the tx is
empty or 0 otherwise. s3c24xx_serial_txempty_nofifo() might return
0x4, and at least uart_get_lsr_info() tries to clear exactly
TIOCSER_TEMT (BIT(1)). Fix tx_empty() to return TIOCSER_TEMT.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-2-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ede8c6f47 ]
Replace g with q.
Helpful when grepping thru source code or logs for
"request" keyword.
Fixes: f65444187a ("serial: New serial driver MAX310X")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e6a92f67c ]
The if (c >= 20 && c <= 0x3f) test added in commit 7a99565f87 is
wrong. 20 is DC4 in ascii and it makes no sense to consider that as the
bottom limit. Instead, it should be 0x20 as in the other test in
the commit above. This is supposed to NOT change anything as we handle
interesting 20-0x20 asciis far before this if.
So for sakeness, change to 0x20 (which is SPACE).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Fixes: 7a99565f87 ("vt: ignore csi sequences with intermediate characters.")
Cc: Martin Hostettler <textshell@uchuujin.de>
Link: https://lore.kernel.org/all/ZaP45QY2WEsDqoxg@neutronstar.dyndns.org/
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b35f8dbbce upstream.
If there is a problem after resetting a port, the do/while() loop that
checks the default value of DIVLSB register may run forever and spam the
I2C bus.
Add a delay before each read of DIVLSB, and a maximum number of tries to
prevent that situation from happening.
Also fail probe if port reset is unsuccessful.
Fixes: 10d8b34a42 ("serial: max310x: Driver rework")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
