commit 9734fd7a27 ("xhci: use pm_ptr() instead of #ifdef for CONFIG_PM
conditionals") did not quite work properly in the 6.1.y branch where it was
applied to fix a build error when CONFIG_PM was set as it left the following
build errors still present:
ERROR: modpost: "xhci_suspend" [drivers/usb/host/xhci-pci.ko] undefined!
ERROR: modpost: "xhci_resume" [drivers/usb/host/xhci-pci.ko] undefined!
Fix this up by properly placing the #ifdef CONFIG_PM in the xhci-pci.c and
hcd.h files to handle this correctly.
Link: https://lore.kernel.org/r/133dbfa0-4a37-4ae0-bb95-1a35f668ec11@w6rz.net
Signed-off-by: Ron Economos <re@w6rz.net>
Link: https://lore.kernel.org/r/d0919169-ee06-4bdd-b2e3-2f776db90971@roeck-us.net
Reported-by: Guenter Roeck <linux@roeck-us.net>
[ Trimmed the partial revert down to an even smaller bit to only be what
is required to fix the build error - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 130eac4170 upstream.
A recent patch caused an unused-function warning in builds with
CONFIG_PM disabled, after the function became marked 'static':
drivers/usb/host/xhci-pci.c:91:13: error: 'xhci_msix_sync_irqs' defined but not used [-Werror=unused-function]
91 | static void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
| ^~~~~~~~~~~~~~~~~~~
This could be solved by adding another #ifdef, but as there is
a trend towards removing CONFIG_PM checks in favor of helper
macros, do the same conversion here and use pm_ptr() to get
either a function pointer or NULL but avoid the warning.
As the hidden functions reference some other symbols, make
sure those are visible at compile time, at the minimal cost of
a few extra bytes for 'struct usb_device'.
Fixes: 9abe15d55d ("xhci: Move xhci MSI sync function to to xhci-pci")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230328131114.1296430-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfc51e48bc upstream.
This commit addresses an issue related to below kernel panic where
panic_on_warn is enabled. It is caused by the unnecessary use of WARN_ON
in functionsfs_bind, which easily leads to the following scenarios.
1.adb_write in adbd 2. UDC write via configfs
================= =====================
->usb_ffs_open_thread() ->UDC write
->open_functionfs() ->configfs_write_iter()
->adb_open() ->gadget_dev_desc_UDC_store()
->adb_write() ->usb_gadget_register_driver_owner
->driver_register()
->StartMonitor() ->bus_add_driver()
->adb_read() ->gadget_bind_driver()
<times-out without BIND event> ->configfs_composite_bind()
->usb_add_function()
->open_functionfs() ->ffs_func_bind()
->adb_open() ->functionfs_bind()
<ffs->state !=FFS_ACTIVE>
The adb_open, adb_read, and adb_write operations are invoked from the
daemon, but trying to bind the function is a process that is invoked by
UDC write through configfs, which opens up the possibility of a race
condition between the two paths. In this race scenario, the kernel panic
occurs due to the WARN_ON from functionfs_bind when panic_on_warn is
enabled. This commit fixes the kernel panic by removing the unnecessary
WARN_ON.
Kernel panic - not syncing: kernel: panic_on_warn set ...
[ 14.542395] Call trace:
[ 14.542464] ffs_func_bind+0x1c8/0x14a8
[ 14.542468] usb_add_function+0xcc/0x1f0
[ 14.542473] configfs_composite_bind+0x468/0x588
[ 14.542478] gadget_bind_driver+0x108/0x27c
[ 14.542483] really_probe+0x190/0x374
[ 14.542488] __driver_probe_device+0xa0/0x12c
[ 14.542492] driver_probe_device+0x3c/0x220
[ 14.542498] __driver_attach+0x11c/0x1fc
[ 14.542502] bus_for_each_dev+0x104/0x160
[ 14.542506] driver_attach+0x24/0x34
[ 14.542510] bus_add_driver+0x154/0x270
[ 14.542514] driver_register+0x68/0x104
[ 14.542518] usb_gadget_register_driver_owner+0x48/0xf4
[ 14.542523] gadget_dev_desc_UDC_store+0xf8/0x144
[ 14.542526] configfs_write_iter+0xf0/0x138
Fixes: ddf8abd259 ("USB: f_fs: the FunctionFS driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Akash M <akash.m5@samsung.com>
Link: https://lore.kernel.org/r/20241219125221.1679-1-akash.m5@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 057bd54dfc upstream.
Currently afunc_bind sets std_ac_if_desc.bNumEndpoints to 1 if
controls (mute/volume) are enabled. During next afunc_bind call,
bNumEndpoints would be unchanged and incorrectly set to 1 even
if the controls aren't enabled.
Fix this by resetting the value of bNumEndpoints to 0 on every
afunc_bind call.
Fixes: eaf6cbe099 ("usb: gadget: f_uac2: add volume and mute support")
Cc: stable <stable@kernel.org>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20241211115915.159864-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0df11fa8ce upstream.
When device_add(&udev->dev) succeeds and a later call fails,
usb_new_device() does not properly call device_del(). As comment of
device_add() says, 'if device_add() succeeds, you should call
device_del() when you want to get rid of it. If device_add() has not
succeeded, use only put_device() to drop the reference count'.
Found by code review.
Cc: stable <stable@kernel.org>
Fixes: 9f8b17e643 ("USB: make usbdevices export their device nodes instead of using a separate class")
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241218071346.2973980-1-make_ruc2021@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59bfeaf545 upstream.
There's USB error when tegra board is shutting down:
[ 180.919315] usb 2-3: Failed to set U1 timeout to 0x0,error code -113
[ 180.919995] usb 2-3: Failed to set U1 timeout to 0xa,error code -113
[ 180.920512] usb 2-3: Failed to set U2 timeout to 0x4,error code -113
[ 186.157172] tegra-xusb 3610000.usb: xHCI host controller not responding, assume dead
[ 186.157858] tegra-xusb 3610000.usb: HC died; cleaning up
[ 186.317280] tegra-xusb 3610000.usb: Timeout while waiting for evaluate context command
The issue is caused by disabling LPM on already suspended ports.
For USB2 LPM, the LPM is already disabled during port suspend. For USB3
LPM, port won't transit to U1/U2 when it's already suspended in U3,
hence disabling LPM is only needed for ports that are not suspended.
Cc: Wayne Chang <waynec@nvidia.com>
Cc: stable <stable@kernel.org>
Fixes: d920a2ed86 ("usb: Disable USB3 LPM at shutdown")
Signed-off-by: Kai-Heng Feng <kaihengf@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20241206074817.89189-1-kaihengf@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a3d76a0b6 upstream.
Fix the regression introduced by commit d8c6edfa3f ("USB:
usblp: don't call usb_set_interface if there's a single alt"),
which causes that unsupported protocols can also be set via
ioctl when the num_altsetting of the device is 1.
Move the check for protocol support to the earlier stage.
Fixes: d8c6edfa3f ("USB: usblp: don't call usb_set_interface if there's a single alt")
Cc: stable <stable@kernel.org>
Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Link: https://lore.kernel.org/r/20241212143852.671889-1-jerrysteve1101@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13014969cb upstream.
Considering that in some extreme cases, when performing the
unbinding operation, gserial_disconnect has cleared gser->ioport,
which triggers gadget reconfiguration, and then calls gs_read_complete,
resulting in access to a null pointer. Therefore, ep is disabled before
gserial_disconnect sets port to null to prevent this from happening.
Call trace:
gs_read_complete+0x58/0x240
usb_gadget_giveback_request+0x40/0x160
dwc3_remove_requests+0x170/0x484
dwc3_ep0_out_start+0xb0/0x1d4
__dwc3_gadget_start+0x25c/0x720
kretprobe_trampoline.cfi_jt+0x0/0x8
kretprobe_trampoline.cfi_jt+0x0/0x8
udc_bind_to_driver+0x1d8/0x300
usb_gadget_probe_driver+0xa8/0x1dc
gadget_dev_desc_UDC_store+0x13c/0x188
configfs_write_iter+0x160/0x1f4
vfs_write+0x2d0/0x40c
ksys_write+0x7c/0xf0
__arm64_sys_write+0x20/0x30
invoke_syscall+0x60/0x150
el0_svc_common+0x8c/0xf8
do_el0_svc+0x28/0xa0
el0_svc+0x24/0x84
Fixes: c1dca562be ("usb gadget: split out serial core")
Cc: stable <stable@kernel.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Link: https://lore.kernel.org/r/TYUPR06MB621733B5AC690DBDF80A0DCCD2042@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01ea6bf5cb upstream.
Before writing a new value to the register, the old value needs to be
masked out for the new value to be programmed as intended, because at
least in some cases the reset value of that field is 0xf (max value).
At the moment, the dwc3 core initialises the threshold to the maximum
value (0xf), with the option to override it via a DT. No upstream DTs
seem to override it, therefore this commit doesn't change behaviour for
any upstream platform. Nevertheless, the code should be fixed to have
the desired outcome.
Do so.
Fixes: 80caf7d21a ("usb: dwc3: add lpm erratum support")
Cc: stable@vger.kernel.org # 5.10+ (needs adjustment for 5.4)
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241209-dwc3-nyet-fix-v2-1-02755683345b@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdef30e077 upstream.
This fixes data corruption when accessing the internal SD card in mass
storage mode.
I am actually not too sure why. I didn't figure a straightforward way to
reproduce the issue, but i seem to get garbage when issuing a lot (over 50)
of large reads (over 120 sectors) are done in a quick succession. That is,
time seems to matter here -- larger reads are fine if they are done with
some delay between them.
But I'm not great at understanding this sort of things, so I'll assume
the issue other, smarter, folks were seeing with similar phones is the
same problem and I'll just put my quirk next to theirs.
The "Software details" screen on the phone is as follows:
V 04.06
07-08-13
RM-849
(c) Nokia
TL;DR version of the device descriptor:
idVendor 0x0421 Nokia Mobile Phones
idProduct 0x06c2
bcdDevice 4.06
iManufacturer 1 Nokia
iProduct 2 Nokia 208
The patch assumes older firmwares are broken too (I'm unable to test, but
no biggie if they aren't I guess), and I have no idea if newer firmware
exists.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250101212206.2386207-1-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 474538b8dd ]
Stop Endpoint command on an already stopped endpoint fails and may be
misinterpreted as a known hardware bug by the completion handler. This
results in an unnecessary delay with repeated retries of the command.
Avoid queuing this command when endpoint state flags indicate that it's
stopped or halted and the command will fail. If commands are pending on
the endpoint, their completion handlers will process cancelled TDs so
it's done. In case of waiting for external operations like clearing TT
buffer, the endpoint is stopped and cancelled TDs can be processed now.
This eliminates practically all unnecessary retries because an endpoint
with pending URBs is maintained in Running state by the driver, unless
aforementioned commands or other operations are pending on it. This is
guaranteed by xhci_ring_ep_doorbell() and by the fact that it is called
every time any of those operations completes.
The only known exceptions are hardware bugs (the endpoint never starts
at all) and Stream Protocol errors not associated with any TRB, which
cause an endpoint reset not followed by restart. Sounds like a bug.
Generally, these retries are only expected to happen when the endpoint
fails to start for unknown/no reason, which is a worse problem itself,
and fixing the bug eliminates the retries too.
All cases were tested and found to work as expected. SET_DEQ_PENDING
was produced by patching uvcvideo to unlink URBs in 100us intervals,
which then runs into this case very often. EP_HALTED was produced by
restarting 'cat /dev/ttyUSB0' on a serial dongle with broken cable.
EP_CLEARING_TT by the same, with the dongle on an external hub.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-34-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e21ebe51af ]
xHC hosts from several vendors have the same issue where endpoints start
so slowly that a later queued 'Stop Endpoint' command may complete before
endpoint is up and running.
The 'Stop Endpoint' command fails with context state error as the endpoint
still appears as stopped.
See commit 42b7581376 ("usb: xhci: Limit Stop Endpoint retries") for
details
CC: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241217102122.2316814-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42b7581376 ]
Some host controllers fail to atomically transition an endpoint to the
Running state on a doorbell ring and enter a hidden "Restarting" state,
which looks very much like Stopped, with the important difference that
it will spontaneously transition to Running anytime soon.
A Stop Endpoint command queued in the Restarting state typically fails
with Context State Error and the completion handler sees the Endpoint
Context State as either still Stopped or already Running. Even a case
of Halted was observed, when an error occurred right after the restart.
The Halted state is already recovered from by resetting the endpoint.
The Running state is handled by retrying Stop Endpoint.
The Stopped state was recognized as a problem on NEC controllers and
worked around also by retrying, because the endpoint soon restarts and
then stops for good. But there is a risk: the command may fail if the
endpoint is "stopped for good" already, and retries will fail forever.
The possibility of this was not realized at the time, but a number of
cases were discovered later and reproduced. Some proved difficult to
deal with, and it is outright impossible to predict if an endpoint may
fail to ever start at all due to a hardware bug. One such bug (albeit
on ASM3142, not on NEC) was found to be reliably triggered simply by
toggling an AX88179 NIC up/down in a tight loop for a few seconds.
An endless retries storm is quite nasty. Besides putting needless load
on the xHC and CPU, it causes URBs never to be given back, paralyzing
the device and connection/disconnection logic for the whole bus if the
device is unplugged. User processes waiting for URBs become unkillable,
drivers and kworker threads lock up and xhci_hcd cannot be reloaded.
For peace of mind, impose a timeout on Stop Endpoint retries in this
case. If they don't succeed in 100ms, consider the endpoint stopped
permanently for some reason and just give back the unlinked URBs. This
failure case is rare already and work is under way to make it rarer.
Start this work today by also handling one simple case of race with
Reset Endpoint, because it costs just two lines to implement.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-32-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: e21ebe51af ("xhci: Turn NEC specific quirk for handling Stop Endpoint errors generic")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd9d55d190 ]
Two NEC uPD720200 adapters have been observed to randomly misbehave:
a Stop Endpoint command fails with Context Error, the Output Context
indicates Stopped state, and the endpoint keeps running. Very often,
Set TR Dequeue Pointer is seen to fail next with Context Error too,
in addition to problems from unexpectedly completed cancelled work.
The pathology is common on fast running isoc endpoints like uvcvideo,
but has also been reproduced on a full-speed bulk endpoint of pl2303.
It seems all EPs are affected, with risk proportional to their load.
Reproduction involves receiving any kind of stream and closing it to
make the device driver cancel URBs already queued in advance.
Deal with it by retrying the command like in the Running state.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: e21ebe51af ("xhci: Turn NEC specific quirk for handling Stop Endpoint errors generic")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1134289b6b ]
When using dma_map_sg() to map the scatterlist with iommu enabled,
the entries in the scatterlist can be mergerd into less but longer
entries in the function __finalise_sg(). So that the number of
valid mapped entries is actually smaller than ureq->num_reqs,and
there are still some invalid entries in the scatterlist with
dma_addr=0xffffffff and len=0. Writing these invalid sg entries
into the dma_desc can cause a data transmission error.
The function dma_map_sg() returns the number of valid map entries
and the return value is assigned to usb_request::num_mapped_sgs in
function usb_gadget_map_request_by_dev(). So that just write valid
mapped entries into dma_desc according to the usb_request::num_mapped_sgs,
and set the IOC bit if it's the last valid mapped entry.
This patch poses no risk to no-iommu situation, cause
ureq->num_mapped_sgs equals ureq->num_sgs while using dma_direct_map_sg()
to map the scatterlist whith iommu disabled.
Signed-off-by: Peng Hongchi <hongchi.peng@siengine.com>
Link: https://lore.kernel.org/r/20240523100315.7226-1-hongchi.peng@siengine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0aca19e403 ]
Some platforms (e.g. ti,j721e-usb, ti,am64-usb) require
this bit to be set to workaround a lockup issue with PHY
short suspend intervals [1]. Add a platform quirk flag
to indicate if Suspend Residency should be enabled.
[1] - https://www.ti.com/lit/er/sprz457h/sprz457h.pdf
i2409 - USB: USB2 PHY locks up due to short suspend
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240516044537.16801-2-r-gunasekaran@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a48f744bef upstream.
When the USB3 PHY is not defined in the Linux device tree, there could
still be a case where there is a USB3 PHY active on the board and enabled
by the first stage bootloader. If serdes clock is being used then the USB
will fail to enumerate devices in 2.0 only mode.
To solve this, make sure that the PIPE clock is deselected whenever the
USB3 PHY is not defined and guarantees that the USB2 only mode will work
in all cases.
Fixes: 9678f3361a ("usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode")
Cc: stable@vger.kernel.org
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/1733163111-1414816-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cfbca86f6 upstream.
Considering that in some extreme cases,
when u_serial driver is accessed by multiple threads,
Thread A is executing the open operation and calling the gs_open,
Thread B is executing the disconnect operation and calling the
gserial_disconnect function,The port->port_usb pointer will be set to NULL.
E.g.
Thread A Thread B
gs_open() gadget_unbind_driver()
gs_start_io() composite_disconnect()
gs_start_rx() gserial_disconnect()
... ...
spin_unlock(&port->port_lock)
status = usb_ep_queue() spin_lock(&port->port_lock)
spin_lock(&port->port_lock) port->port_usb = NULL
gs_free_requests(port->port_usb->in) spin_unlock(&port->port_lock)
Crash
This causes thread A to access a null pointer (port->port_usb is null)
when calling the gs_free_requests function, causing a crash.
If port_usb is NULL, the release request will be skipped as it
will be done by gserial_disconnect.
So add a null pointer check to gs_start_io before attempting
to access the value of the pointer port->port_usb.
Call trace:
gs_start_io+0x164/0x25c
gs_open+0x108/0x13c
tty_open+0x314/0x638
chrdev_open+0x1b8/0x258
do_dentry_open+0x2c4/0x700
vfs_open+0x2c/0x3c
path_openat+0xa64/0xc60
do_filp_open+0xb8/0x164
do_sys_openat2+0x84/0xf0
__arm64_sys_openat+0x70/0x9c
invoke_syscall+0x58/0x114
el0_svc_common+0x80/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x38/0x68
Fixes: c1dca562be ("usb gadget: split out serial core")
Cc: stable@vger.kernel.org
Suggested-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Acked-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/TYUPR06MB62178DC3473F9E1A537DCD02D2362@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef42b906df upstream.
The refcounts of the OF nodes obtained by of_get_child_by_name() calls
in anx7411_typec_switch_probe() are not decremented. Replace them with
device_get_named_child_node() calls and store the return values to the
newly created fwnode_handle fields in anx7411_data, and call
fwnode_handle_put() on them in the error path and in the unregister
functions.
Fixes: e45d7337dc ("usb: typec: anx7411: Use of_get_child_by_name() instead of of_find_node_by_name()")
Cc: stable@vger.kernel.org
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241126014909.3687917-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 645d56e4cc upstream.
An fwnode_handle and usb_role_switch are obtained with an incremented
refcount in anx7411_typec_port_probe(), however the refcounts are not
decremented in the error path. The fwnode_handle is also not decremented
in the .remove() function. Therefore, call fwnode_handle_put() and
usb_role_switch_put() accordingly.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Cc: stable@vger.kernel.org
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241121023429.962848-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97264eaaba upstream.
If the clocks priv->iclk and priv->fclk were not enabled in ehci_hcd_sh_probe,
they should not be disabled in any path.
Conversely, if they was enabled in ehci_hcd_sh_probe, they must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 63c8455222 ("usb: ehci-hcd: Add support for SuperH EHCI.")
Cc: stable@vger.kernel.org # ff30bd6a66: sh: clk: Fix clk_enable() to return 0 on NULL clk
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241121114700.2100520-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cf1bd88f1 upstream.
On Raspberry Pis without onboard USB hub frequent device reconnects
can trigger a interrupt storm after DWC2 entered host clock gating.
This is caused by a race between _dwc2_hcd_suspend() and the port
interrupt, which sets port_connect_status. The issue occurs if
port_connect_status is still 1, but there is no connection anymore:
usb 1-1: USB disconnect, device number 25
dwc2 3f980000.usb: _dwc2_hcd_suspend: port_connect_status: 1
dwc2 3f980000.usb: Entering host clock gating.
Disabling IRQ #66
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.0-gc1bb81b13202-dirty #322
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1d01f20 to 0xc1d01f68)
1f20: 0004ef3c 00000001 00000000 00000000 c1d09780 c1f6bb5c c1d04e54 c1c60ca8
1f40: c1d04e94 00000000 00000000 c1d092a8 c1f6af20 c1d01f70 c1211b98 c1212f40
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<e3a25c00>] dwc2_handle_common_intr
[<58bf98a3>] usb_hcd_irq
Disabling IRQ #66
So avoid this by reading the connection status directly.
Fixes: 113f86d0c3 ("usb: dwc2: Update partial power down entering by system suspend")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-4-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8d3e4a734 upstream.
On Rasperry Pis without onboard USB hub the power cycle during
power connect init only disable the port but never enabled it again:
usb usb1-port1: attempt power cycle
The port relevant part in dwc2_hcd_hub_control() is skipped in case
port_connect_status = 0 under the assumption the core is or will be soon
in device mode. But this assumption is wrong, because after ClearPortFeature
USB_PORT_FEAT_POWER the port_connect_status will also be 0 and
SetPortFeature (incl. USB_PORT_FEAT_POWER) will be a no-op.
Fix the behavior of dwc2_hcd_hub_control() by replacing the
port_connect_status check with dwc2_is_device_mode().
Link: https://github.com/raspberrypi/linux/issues/6247
Fixes: 7359d482eb ("staging: HCD files for the DWC2 driver")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 336f72d3cb upstream.
The Raspberry Pi can suffer on interrupt storms on HCD resume. The dwc2
driver sometimes misses to enable HCD_FLAG_HW_ACCESSIBLE before re-enabling
the interrupts. This causes a situation where both handler ignore a incoming
port interrupt and force the upper layers to disable the dwc2 interrupt
line. This leaves the USB interface in a unusable state:
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 6.10.0-rc3
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1b01f20 to 0xc1b01f68)
1f20: 0005c0d4 00000001 00000000 00000000 c1b09780 c1d6b32c c1b04e54 c1a5eae8
1f40: c1b04e90 00000000 00000000 00000000 c1d6a8a0 c1b01f70 c11d2da8 c11d4160
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<f539e0f4>] dwc2_handle_common_intr
[<75cd278b>] usb_hcd_irq
Disabling IRQ #66
So enable the HCD_FLAG_HW_ACCESSIBLE flag in case there is a port
connection.
Fixes: c74c26f6e3 ("usb: dwc2: Fix partial power down exiting by system resume")
Closes: https://lore.kernel.org/linux-usb/3fd0c2fb-4752-45b3-94eb-42352703e1fd@gmx.net/T/
Link: https://lore.kernel.org/all/5e8cbce0-3260-2971-484f-fc73a3b2bd28@synopsys.com/
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d2ada0522 upstream.
If the current USB request was aborted, the spi thread would not respond
to any further requests. This is because the "curr_urb" pointer would
not become NULL, so no further requests would be taken off the queue.
The solution here is to set the "urb_done" flag, as this will cause the
correct handling of the URB. Also clear interrupts that should only be
expected if an URB is in progress.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20241124221430.1106080-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2e0eee470 upstream.
The DWC3_EP_RESOURCE_ALLOCATED flag ensures that the resource of an
endpoint is only assigned once. Unless the endpoint is reset, don't
clear this flag. Otherwise we may set endpoint resource again, which
prevents the driver from initiate transfer after handling a STALL or
endpoint halt to the control endpoint.
Cc: stable@vger.kernel.org
Fixes: b311048c17 ("usb: dwc3: gadget: Rewrite endpoint allocation flow")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/00122b7cc5be06abef461776e7cc9f5ebc8bc1cb.1713229786.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9044ad57b6 upstream.
Don't flush all pending DbC data requests when an endpoint halts.
An endpoint may halt and xHC DbC triggers a STALL error event if there's
an issue with a bulk data transfer. The transfer should restart once xHC
DbC receives a ClearFeature(ENDPOINT_HALT) request from the host.
Once xHC DbC restarts it will start from the TRB pointed to by dequeue
field in the endpoint context, which might be the same TRB we got the
STALL event for. Turn the TRB to a no-op in this case to make sure xHC
DbC doesn't reuse and tries to retransmit this same TRB after we already
handled it, and gave its corresponding data request back.
Other STALL events might be completely bogus.
Lukasz Bartosik discovered that xHC DbC might issue spurious STALL events
if hosts sends a ClearFeature(ENDPOINT_HALT) request to non-halted
endpoints even without any active bulk transfers.
Assume STALL event is spurious if it reports 0 bytes transferred, and
the endpoint stopped on the STALLED TRB.
Don't give back the data request corresponding to the TRB in this case.
The halted status is per endpoint. Track it with a per endpoint flag
instead of the driver invented DbC wide DS_STALLED state.
DbC remains in DbC-Configured state even if endpoints halt. There is no
Stalled state in the DbC Port state Machine (xhci section 7.6.6)
Reported-by: Łukasz Bartosik <ukaszb@chromium.org>
Closes: https://lore.kernel.org/linux-usb/20240725074857.623299-1-ukaszb@chromium.org/
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 548f48b66c ]
As per USBSTS register description about UEI:
When completion of a USB transaction results in an error condition, this
bit is set by the Host/Device Controller. This bit is set along with the
USBINT bit, if the TD on which the error interrupt occurred also had its
interrupt on complete (IOC) bit set.
UI is set only when IOC set. Add checking UEI to fix miss call
isr_tr_complete_handler() when IOC have not set and transfer error happen.
Acked-by: Peter Chen <peter.chen@kernel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240926022906.473319-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d2fb074de ]
The driver cannot issue the End Transfer command to the SETUP transfer.
Don't clear DWC3_EP_TRANSFER_STARTED flag to make sure that the driver
won't send Start Transfer command again, which can cause no-resource
error. For example this can occur if the host issues a reset to the
device.
Cc: stable@vger.kernel.org
Fixes: 76cb323f80 ("usb: dwc3: ep0: clear all EP0 flags")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d3d618185fd614bb7426352a9fc1199641d3b5f5.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72fca8371f ]
The DWC3_EP_RESOURCE_ALLOCATED flag ensures that the resource of an
endpoint is only assigned once. Unless the endpoint is reset, don't
clear this flag. Otherwise we may set endpoint resource again, which
prevents the driver from initiate transfer after handling a STALL or
endpoint halt to the control endpoint.
Commit f2e0eee470 ("usb: dwc3: ep0: Don't reset resource alloc flag")
was fixing the initial issue, but did this only for physical ep1. Since
the function dwc3_ep0_stall_and_restart is resetting the flags for both
physical endpoints, this also has to be done for ep0.
Cc: stable@vger.kernel.org
Fixes: b311048c17 ("usb: dwc3: gadget: Rewrite endpoint allocation flow")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240814-dwc3hwep0reset-v2-1-29e1d7d923ea@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 5d2fb074de ("usb: dwc3: ep0: Don't clear ep0 DWC3_EP_TRANSFER_STARTED")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b311048c17 ]
The driver dwc3 deviates from the programming guide in regard to
endpoint configuration. It does this command sequence:
DEPSTARTCFG -> DEPXFERCFG -> DEPCFG
Instead of the suggested flow:
DEPSTARTCFG -> DEPCFG -> DEPXFERCFG
The reasons for this deviation were as follow, quoted:
1) The databook says to do %DWC3_DEPCMD_DEPSTARTCFG for every
%USB_REQ_SET_CONFIGURATION and %USB_REQ_SET_INTERFACE
(8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more
%DWC3_DEPCMD_DEPXFERCFG for new endpoint on alt setting
(8.1.6).
Regarding 1), DEPSTARTCFG resets the endpoints' resource and can be a
problem if used with SET_INTERFACE request of a multiple interface
configuration. But we can still satisfy the programming guide
requirement by assigning the endpoint resource as part of
usb_ep_enable(). We will only reset endpoint resources on controller
initialization and SET_CONFIGURATION request.
Regarding 2), the later versions of the programming guide were updated
to clarify this flow (see "Alternate Initialization on SetInterface
Request" of the programming guide). As long as the platform has enough
physical endpoints, we can assign resource to a new endpoint.
The order of the command sequence will not be a problem to most
platforms for the current implementation of the dwc3 driver. However,
this order is required in different scenarios (such as initialization
during controller's hibernation restore). Let's keep the flow consistent
and follow the programming guide.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/c143583a5afb087deb8c3aa5eb227ee23515f272.1706754219.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 5d2fb074de ("usb: dwc3: ep0: Don't clear ep0 DWC3_EP_TRANSFER_STARTED")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b7fc65f514 upstream.
The dwc3_request->num_queued_sgs is decremented on completion. If a
partially completed request is handled, then the
dwc3_request->num_queued_sgs no longer reflects the total number of
num_queued_sgs (it would be cleared).
Correctly check the number of request SG entries remained to be prepare
and queued. Failure to do this may cause null pointer dereference when
accessing non-existent SG entry.
Cc: stable@vger.kernel.org
Fixes: c96e6725db ("usb: dwc3: gadget: Correct the logic for queuing sgs")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d07a7c4aa0fcf746cdca0515150dbe5c52000af7.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02a6982b0c upstream.
The check whether the TRB ring is full or empty in dwc3_calc_trbs_left()
is insufficient. It assumes there are active TRBs if there's any request
in the started_list. However, that's not the case for requests with a
large SG list.
That is, if we have a single usb request that requires more TRBs than
the total TRBs in the TRB ring, the queued TRBs will be available when
all the TRBs in the ring are completed. But the request is only
partially completed and remains in the started_list. With the current
logic, the TRB ring is empty, but dwc3_calc_trbs_left() returns 0.
Fix this by additionally checking for the request->num_trbs for active
TRB count.
Cc: stable@vger.kernel.org
Fixes: 51f1954ad8 ("usb: dwc3: gadget: Fix dwc3_calc_trbs_left()")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/708dc62b56b77da1f704cc2ae9b6ddb1f2dbef1f.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fc137386c upstream.
There is a possibility that a request's callback could be invoked from
usb_ep_queue() (call trace below, supplemented with missing calls):
req->complete from usb_gadget_giveback_request
(drivers/usb/gadget/udc/core.c:999)
usb_gadget_giveback_request from musb_g_giveback
(drivers/usb/musb/musb_gadget.c:147)
musb_g_giveback from rxstate
(drivers/usb/musb/musb_gadget.c:784)
rxstate from musb_ep_restart
(drivers/usb/musb/musb_gadget.c:1169)
musb_ep_restart from musb_ep_restart_resume_work
(drivers/usb/musb/musb_gadget.c:1176)
musb_ep_restart_resume_work from musb_queue_resume_work
(drivers/usb/musb/musb_core.c:2279)
musb_queue_resume_work from musb_gadget_queue
(drivers/usb/musb/musb_gadget.c:1241)
musb_gadget_queue from usb_ep_queue
(drivers/usb/gadget/udc/core.c:300)
According to the docstring of usb_ep_queue(), this should not happen:
"Note that @req's ->complete() callback must never be called from within
usb_ep_queue() as that can create deadlock situations."
In fact, a hardware lockup might occur in the following sequence:
1. The gadget is initialized using musb_gadget_enable().
2. Meanwhile, a packet arrives, and the RXPKTRDY flag is set, raising an
interrupt.
3. If IRQs are enabled, the interrupt is handled, but musb_g_rx() finds an
empty queue (next_request() returns NULL). The interrupt flag has
already been cleared by the glue layer handler, but the RXPKTRDY flag
remains set.
4. The first request is enqueued using usb_ep_queue(), leading to the call
of req->complete(), as shown in the call trace above.
5. If the callback enables IRQs and another packet is waiting, step (3)
repeats. The request queue is empty because usb_g_giveback() removes the
request before invoking the callback.
6. The endpoint remains locked up, as the interrupt triggered by hardware
setting the RXPKTRDY flag has been handled, but the flag itself remains
set.
For this scenario to occur, it is only necessary for IRQs to be enabled at
some point during the complete callback. This happens with the USB Ethernet
gadget, whose rx_complete() callback calls netif_rx(). If called in the
task context, netif_rx() disables the bottom halves (BHs). When the BHs are
re-enabled, IRQs are also enabled to allow soft IRQs to be processed. The
gadget itself is initialized at module load (or at boot if built-in), but
the first request is enqueued when the network interface is brought up,
triggering rx_complete() in the task context via ioctl(). If a packet
arrives while the interface is down, it can prevent the interface from
receiving any further packets from the USB host.
The situation is quite complicated with many parties involved. This
particular issue can be resolved in several possible ways:
1. Ensure that callbacks never enable IRQs. This would be difficult to
enforce, as discovering how netif_rx() interacts with interrupts was
already quite challenging and u_ether is not the only function driver.
Similar "bugs" could be hidden in other drivers as well.
2. Disable MUSB interrupts in musb_g_giveback() before calling the callback
and re-enable them afterwars (by calling musb_{dis,en}able_interrupts(),
for example). This would ensure that MUSB interrupts are not handled
during the callback, even if IRQs are enabled. In fact, it would allow
IRQs to be enabled when releasing the lock. However, this feels like an
inelegant hack.
3. Modify the interrupt handler to clear the RXPKTRDY flag if the request
queue is empty. While this approach also feels like a hack, it wastes
CPU time by attempting to handle incoming packets when the software is
not ready to process them.
4. Flush the Rx FIFO instead of calling rxstate() in musb_ep_restart().
This ensures that the hardware can receive packets when there is at
least one request in the queue. Once IRQs are enabled, the interrupt
handler will be able to correctly process the next incoming packet
(eventually calling rxstate()). This approach may cause one or two
packets to be dropped (two if double buffering is enabled), but this
seems to be a minor issue, as packet loss can occur when the software is
not yet ready to process them. Additionally, this solution makes the
gadget driver compliant with the rule mentioned in the docstring of
usb_ep_queue().
There may be additional solutions, but from these four, the last one has
been chosen as it seems to be the most appropriate, as it addresses the
"bad" behavior of the driver.
Fixes: baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
Cc: stable@vger.kernel.org
Signed-off-by: Hubert Wiśniewski <hubert.wisniewski.25632@gmail.com>
Link: https://lore.kernel.org/r/4ee1ead4525f78fb5909a8cbf99513ad0082ad21.camel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51cdd69d6a upstream.
This reverts commit ec6ce7075e.
Fix installation of WinUSB driver using OS descriptors. Without the
fix the drivers are not installed correctly and the property
'DeviceInterfaceGUID' is missing on host side.
The original change was based on the assumption that the interface
number is in the high byte of wValue but it is in the low byte,
instead. Unfortunately, the fix is based on MS documentation which is
also wrong.
The actual USB request for OS descriptors (using USB analyzer) looks
like:
Offset 0 1 2 3 4 5 6 7
0x000 C1 A1 02 00 05 00 0A 00
C1: bmRequestType (device to host, vendor, interface)
A1: nas magic number
0002: wValue (2: nas interface)
0005: wIndex (5: get extended property i.e. nas interface GUID)
008E: wLength (142)
The fix was tested on Windows 10 and Windows 11.
Cc: stable@vger.kernel.org
Fixes: ec6ce7075e ("usb: gadget: composite: fix OS descriptors w_value logic")
Signed-off-by: Michal Vrastil <michal.vrastil@hidglobal.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Peter korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20241113235433.20244-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 484c3bab2d upstream.
xhci_invalidate_cancelled_tds() may not work correctly if the hardware
is modifying endpoint or stream contexts at the same time by executing
a Set TR Dequeue command. And even if it worked, it would be unable to
queue Set TR Dequeue for the next stream, failing to clear xHC cache.
On stream endpoints, a chain of Set TR Dequeue commands may take some
time to execute and we may want to cancel more TDs during this time.
Currently this leads to Stop Endpoint completion handler calling this
function without testing for SET_DEQ_PENDING, which will trigger the
aforementioned problems when it happens.
On all endpoints, a halt condition causes Reset Endpoint to be queued
and an error status given to the class driver, which may unlink more
URBs in response. Stop Endpoint is queued and its handler may execute
concurrently with Set TR Dequeue queued by Reset Endpoint handler.
(Reset Endpoint handler calls this function too, but there seems to
be no possibility of it running concurrently with Set TR Dequeue).
Fix xhci_invalidate_cancelled_tds() to work correctly under a pending
Set TR Dequeue. Bail out of the function when SET_DEQ_PENDING is set,
then make the completion handler call the function again and also call
xhci_giveback_invalidated_tds(), which needs to be called next.
This seems to fix another potential bug, where the handler would call
xhci_invalidate_cancelled_tds(), which may clear some deferred TDs if
a sanity check fails, and the TDs wouldn't be given back promptly.
Said sanity check seems to be wrong and prone to false positives when
the endpoint halts, but fixing it is beyond the scope of this change,
besides ensuring that cleared TDs are given back properly.
Fixes: 5ceac4402f ("xhci: Handle TD clearing for multiple streams case")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-33-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40c9748267 upstream.
If the clock sehci->clk was not enabled in spear_ehci_hcd_drv_probe,
it should not be disabled in any path.
Conversely, if it was enabled in spear_ehci_hcd_drv_probe, it must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 7675d6ba43 ("USB: EHCI: make ehci-spear a separate driver")
Cc: stable@vger.kernel.org
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241114230310.432213-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d73dc7b182 ]
[Syzbot reported two possible deadlocks]
The first possible deadlock is:
WARNING: possible recursive locking detected
6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted
--------------------------------------------
syz-executor363/2651 is trying to acquire lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x15d/0x2c0 drivers/usb/misc/chaoskey.c:322
but task is already holding lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x7f/0x2c0 drivers/usb/misc/chaoskey.c:299
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(chaoskey_list_lock);
lock(chaoskey_list_lock);
*** DEADLOCK ***
The second possible deadlock is:
WARNING: possible circular locking dependency detected
6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted
------------------------------------------------------
kworker/0:2/804 is trying to acquire lock:
ffffffff899dadb0 (minor_rwsem){++++}-{3:3}, at: usb_deregister_dev+0x7c/0x1e0 drivers/usb/core/file.c:186
but task is already holding lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_disconnect+0xa8/0x2a0 drivers/usb/misc/chaoskey.c:235
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (chaoskey_list_lock){+.+.}-{3:3}:
__mutex_lock_common kernel/locking/mutex.c:608 [inline]
__mutex_lock+0x175/0x9c0 kernel/locking/mutex.c:752
chaoskey_open+0xdd/0x220 drivers/usb/misc/chaoskey.c:274
usb_open+0x186/0x220 drivers/usb/core/file.c:47
chrdev_open+0x237/0x6a0 fs/char_dev.c:414
do_dentry_open+0x6cb/0x1390 fs/open.c:958
vfs_open+0x82/0x3f0 fs/open.c:1088
do_open fs/namei.c:3774 [inline]
path_openat+0x1e6a/0x2d60 fs/namei.c:3933
do_filp_open+0x1dc/0x430 fs/namei.c:3960
do_sys_openat2+0x17a/0x1e0 fs/open.c:1415
do_sys_open fs/open.c:1430 [inline]
__do_sys_openat fs/open.c:1446 [inline]
__se_sys_openat fs/open.c:1441 [inline]
__x64_sys_openat+0x175/0x210 fs/open.c:1441
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
-> #0 (minor_rwsem){++++}-{3:3}:
check_prev_add kernel/locking/lockdep.c:3161 [inline]
check_prevs_add kernel/locking/lockdep.c:3280 [inline]
validate_chain kernel/locking/lockdep.c:3904 [inline]
__lock_acquire+0x250b/0x3ce0 kernel/locking/lockdep.c:5202
lock_acquire.part.0+0x11b/0x380 kernel/locking/lockdep.c:5825
down_write+0x93/0x200 kernel/locking/rwsem.c:1577
usb_deregister_dev+0x7c/0x1e0 drivers/usb/core/file.c:186
chaoskey_disconnect+0xb7/0x2a0 drivers/usb/misc/chaoskey.c:236
usb_unbind_interface+0x1e8/0x970 drivers/usb/core/driver.c:461
device_remove drivers/base/dd.c:569 [inline]
device_remove+0x122/0x170 drivers/base/dd.c:561
__device_release_driver drivers/base/dd.c:1273 [inline]
device_release_driver_internal+0x44a/0x610 drivers/base/dd.c:1296
bus_remove_device+0x22f/0x420 drivers/base/bus.c:576
device_del+0x396/0x9f0 drivers/base/core.c:3864
usb_disable_device+0x36c/0x7f0 drivers/usb/core/message.c:1418
usb_disconnect+0x2e1/0x920 drivers/usb/core/hub.c:2304
hub_port_connect drivers/usb/core/hub.c:5361 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5661 [inline]
port_event drivers/usb/core/hub.c:5821 [inline]
hub_event+0x1bed/0x4f40 drivers/usb/core/hub.c:5903
process_one_work+0x9c5/0x1ba0 kernel/workqueue.c:3229
process_scheduled_works kernel/workqueue.c:3310 [inline]
worker_thread+0x6c8/0xf00 kernel/workqueue.c:3391
kthread+0x2c1/0x3a0 kernel/kthread.c:389
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(chaoskey_list_lock);
lock(minor_rwsem);
lock(chaoskey_list_lock);
lock(minor_rwsem);
*** DEADLOCK ***
[Analysis]
The first is AA lock, it because wrong logic, it need a unlock.
The second is AB lock, it needs to rearrange the order of lock usage.
Fixes: 422dc0a4d1 ("USB: chaoskey: fail open after removal")
Reported-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com
Reported-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=685e14d04fe35692d3bc
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Tested-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com
Reported-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com
Tested-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com
Tested-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/tencent_84EB865C89862EC22EE94CB3A7C706C59206@qq.com
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 422dc0a4d1 ]
chaoskey_open() takes the lock only to increase the
counter of openings. That means that the mutual exclusion
with chaoskey_disconnect() cannot prevent an increase
of the counter and chaoskey_open() returning a success.
If that race is hit, chaoskey_disconnect() will happily
free all resources associated with the device after
it has dropped the lock, as it has read the counter
as zero.
To prevent this race chaoskey_open() has to check
the presence of the device under the lock.
However, the current per device lock cannot be used,
because it is a part of the data structure to be
freed. Hence an additional global mutex is needed.
The issue is as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+422188bce66e76020e55@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=422188bce66e76020e55
Fixes: 66e3e59189 ("usb: Add driver for Altus Metrum ChaosKey device (v2)")
Rule: add
Link: https://lore.kernel.org/stable/20241002132201.552578-1-oneukum%40suse.com
Link: https://lore.kernel.org/r/20241002132201.552578-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0aa9614ab ]
The IO yurex_write() needs to wait for in order to have a device
ready for writing again can take a long time time.
Consequently the sleep is done in an interruptible state.
Therefore others waiting for yurex_write() itself to finish should
use mutex_lock_interruptible.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Rule: add
Link: https://lore.kernel.org/stable/20240924084415.300557-1-oneukum%40suse.com
Link: https://lore.kernel.org/r/20240924084415.300557-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44feafbaa6 ]
iowarrior_read() uses the iowarrior dev structure, but does not use any
lock on the structure. This can cause various bugs including data-races,
so it is more appropriate to use a mutex lock to safely protect the
iowarrior dev structure. When using a mutex lock, you should split the
branch to prevent blocking when the O_NONBLOCK flag is set.
In addition, it is unnecessary to check for NULL on the iowarrior dev
structure obtained by reading file->private_data. Therefore, it is
better to remove the check.
Fixes: 946b960d13 ("USB: add driver for iowarrior devices.")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Link: https://lore.kernel.org/r/20240919103403.3986-1-aha310510@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
