commit 36dd7a4c62 upstream.
Commit e3fffc1f0b ("devicetree: document new marvell-8xxx and
pwrseq-sd8787 options") documented a compatible string for SD8787 in
the devicetree bindings, but neglected to add it to the mwifiex driver.
Fixes: e3fffc1f0b ("devicetree: document new marvell-8xxx and pwrseq-sd8787 options")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.11+
Cc: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/320de5005ff3b8fd76be2d2b859fd021689c3681.1674827105.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 821de68c1f ]
Unsupported port speed can be set and cause error. Now fixing it
and return an error if setting unsupported speed.
This fix depends on the following, which was included in v6.2-rc1:
commit a61474c41e ("nfp: ethtool: support reporting link modes").
Fixes: 7c69873727 ("nfp: add support for .set_link_ksettings()")
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a61474c41e ]
Add support for reporting link modes,
including `Supported link modes` and `Advertised link modes`,
via ethtool $DEV.
A new command `SPCODE_READ_MEDIA` is added to read info from
management firmware. Also, the mapping table `nfp_eth_media_table`
associates the link modes between NFP and kernel. Both of them
help to support this ability.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/r/20221125113030.141642-1-simon.horman@corigine.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 821de68c1f ("nfp: ethtool: fix the bug of setting unsupported port speed")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f006229135 ]
Debian's gcc-13 [1] throws the following error in
kvaser_usb_hydra_cmd_size():
[1] gcc version 13.0.0 20221214 (experimental) [master r13-4693-g512098a3316] (Debian 13-20221214-1)
| drivers/net/can/usb/kvaser_usb/kvaser_usb_hydra.c:502:65: error:
| array subscript ‘struct kvaser_cmd_ext[0]’ is partly outside array
| bounds of ‘unsigned char[32]’ [-Werror=array-bounds=]
| 502 | ret = le16_to_cpu(((struct kvaser_cmd_ext *)cmd)->len);
kvaser_usb_hydra_cmd_size() returns the size of given command. It
depends on the command number (cmd->header.cmd_no). For extended
commands (cmd->header.cmd_no == CMD_EXTENDED) the above shown code is
executed.
Help gcc to recognize that this code path is not taken in all cases,
by calling kvaser_usb_hydra_cmd_size() directly after assigning the
command number.
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/all/20221219110104.1073881-1-mkl@pengutronix.de
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 791082ec0a ]
Re-enable the function rtl8xxxu_gen2_report_connect.
It informs the firmware when connecting to a network. This makes the
firmware enable the rate control, which makes the upload faster.
It also informs the firmware when disconnecting from a network. In the
past this made reconnecting impossible because it was sending the
auth on queue 0x7 (TXDESC_QUEUE_VO) instead of queue 0x12
(TXDESC_QUEUE_MGNT):
wlp0s20f0u3: send auth to 90:55:de:__:__:__ (try 1/3)
wlp0s20f0u3: send auth to 90:55:de:__:__:__ (try 2/3)
wlp0s20f0u3: send auth to 90:55:de:__:__:__ (try 3/3)
wlp0s20f0u3: authentication with 90:55:de:__:__:__ timed out
Probably the firmware disables the unnecessary TX queues when it
knows it's disconnected.
However, this was fixed in commit edd5747aa1 ("wifi: rtl8xxxu: Fix
skb misuse in TX queue selection").
Fixes: c59f13bbea ("rtl8xxxu: Work around issue with 8192eu and 8723bu devices not reconnecting")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/43200afc-0c65-ee72-48f8-231edd1df493@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f74878433d ]
Commit 26f3a021b3 ("ath11k: allocate smaller chunks of memory for
firmware") and commit f6f92968e1 ("ath11k: qmi: try to allocate a
big block of DMA memory first") change ath11k to allocate the memory
chunks for target twice while wlan load. It fails for the 1st time
because of large memory and then changed to allocate many small chunks
for the 2nd time sometimes as below log.
1st time failed:
[10411.640620] ath11k_pci 0000:05:00.0: qmi firmware request memory request
[10411.640625] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 6881280
[10411.640630] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 3784704
[10411.640658] ath11k_pci 0000:05:00.0: qmi dma allocation failed (6881280 B type 1), will try later with small size
[10411.640671] ath11k_pci 0000:05:00.0: qmi delays mem_request 2
[10411.640677] ath11k_pci 0000:05:00.0: qmi respond memory request delayed 1
2nd time success:
[10411.642004] ath11k_pci 0000:05:00.0: qmi firmware request memory request
[10411.642008] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642012] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642014] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642016] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642018] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642020] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642022] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642024] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642027] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642029] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642031] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 458752
[10411.642033] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 131072
[10411.642035] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642037] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642039] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642041] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642043] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642045] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642047] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 491520
[10411.642049] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
And then commit 5962f370ce ("ath11k: Reuse the available memory after
firmware reload") skip the ath11k_qmi_free_resource() which frees the
memory chunks while recovery, after that, when run recovery test on
WCN6855, a warning happened every time as below and finally leads fail
for recovery.
[ 159.570318] BUG: Bad page state in process kworker/u16:5 pfn:33300
[ 159.570320] page:0000000096ffdbb9 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x33300
[ 159.570324] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
[ 159.570329] raw: 000fffffc0000000 0000000000000000 dead000000000122 0000000000000000
[ 159.570332] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[ 159.570334] page dumped because: nonzero _refcount
[ 159.570440] firewire_ohci syscopyarea sysfillrect psmouse sdhci_pci ahci sysimgblt firewire_core fb_sys_fops libahci crc_itu_t cqhci drm sdhci e1000e wmi video
[ 159.570460] CPU: 2 PID: 217 Comm: kworker/u16:5 Kdump: loaded Tainted: G B 5.19.0-rc1-wt-ath+ #3
[ 159.570465] Hardware name: LENOVO 418065C/418065C, BIOS 83ET63WW (1.33 ) 07/29/2011
[ 159.570467] Workqueue: qmi_msg_handler qmi_data_ready_work [qmi_helpers]
[ 159.570475] Call Trace:
[ 159.570476] <TASK>
[ 159.570478] dump_stack_lvl+0x49/0x5f
[ 159.570486] dump_stack+0x10/0x12
[ 159.570493] bad_page+0xab/0xf0
[ 159.570502] check_free_page_bad+0x66/0x70
[ 159.570511] __free_pages_ok+0x530/0x9a0
[ 159.570517] ? __dev_printk+0x58/0x6b
[ 159.570525] ? _dev_printk+0x56/0x72
[ 159.570534] ? qmi_decode+0x119/0x470 [qmi_helpers]
[ 159.570543] __free_pages+0x91/0xd0
[ 159.570548] dma_free_contiguous+0x50/0x60
[ 159.570556] dma_direct_free+0xe5/0x140
[ 159.570564] dma_free_attrs+0x35/0x50
[ 159.570570] ath11k_qmi_msg_mem_request_cb+0x2ae/0x3c0 [ath11k]
[ 159.570620] qmi_invoke_handler+0xac/0xe0 [qmi_helpers]
[ 159.570630] qmi_handle_message+0x6d/0x180 [qmi_helpers]
[ 159.570643] qmi_data_ready_work+0x2ca/0x440 [qmi_helpers]
[ 159.570656] process_one_work+0x227/0x440
[ 159.570667] worker_thread+0x31/0x3d0
[ 159.570676] ? process_one_work+0x440/0x440
[ 159.570685] kthread+0xfe/0x130
[ 159.570692] ? kthread_complete_and_exit+0x20/0x20
[ 159.570701] ret_from_fork+0x22/0x30
[ 159.570712] </TASK>
The reason is because when wlan start to recovery, the type, size and
count is not same for the 1st and 2nd QMI_WLFW_REQUEST_MEM_IND message,
Then it leads the parameter size is not correct for the dma_free_coherent().
For the chunk[1], the actual dma size is 524288 which allocate in the
2nd time of the initial wlan load phase, and the size which pass to
dma_free_coherent() is 3784704 which is got in the 1st time of recovery
phase, then warning above happened.
Change to use prev_size of struct target_mem_chunk for the paramter of
dma_free_coherent() since prev_size is the real size of last load/recovery.
Also change to check both type and size of struct target_mem_chunk to
reuse the memory to avoid mismatch buffer size for target. Then the
warning disappear and recovery success. When the 1st QMI_WLFW_REQUEST_MEM_IND
for recovery arrived, the trunk[0] is freed in ath11k_qmi_alloc_target_mem_chunk()
and then dma_alloc_coherent() failed caused by large size, and then
trunk[1] is freed in ath11k_qmi_free_target_mem_chunk(), the left 18
trunks will be reuse for the 2nd QMI_WLFW_REQUEST_MEM_IND message.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 5962f370ce ("ath11k: Reuse the available memory after firmware reload")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220928073832.16251-1-quic_wgong@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fa0b526f8 ]
The result of nlmsg_find_attr() 'br_spec' is dereferenced in
nla_for_each_nested(), but it can take NULL value in nla_find() function,
which will result in an error.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 51616018dd ("i40e: Add support for getlink, setlink ndo ops")
Signed-off-by: Natalia Petrova <n.petrova@fintech.ru>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230209172833.3596034-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0967bf8377 upstream.
Include the second VLAN HLEN into account when computing the maximum
MTU size as other drivers do.
Fixes: fabf1bce10 ("ixgbe: Prevent unsupported configurations with XDP")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 207ce626ad upstream.
Fix handling of the tsync interrupt to compare the pin number with
IGB_N_SDP instead of IGB_N_EXTTS/IGB_N_PEROUT and fix the indexing to
the perout array.
Fixes: cf99c1dd7b ("igb: move PEROUT and EXTTS isr logic to separate functions")
Reported-by: Matt Corallo <ntp-lists@mattcorallo.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230213185822.3960072-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d54cb1767 upstream.
Commit a97f8783a9 ("igb: unbreak I2C bit-banging on i350") introduced
code to change I2C settings to bit banging unconditionally.
However, this patch introduced a regression: On an Intel S2600CWR
Server Board with three NICs:
- 1x dual-port copper
Intel I350 Gigabit Network Connection [8086:1521] (rev 01)
fw 1.63, 0x80000dda
- 2x quad-port SFP+ with copper SFP Avago ABCU-5700RZ
Intel I350 Gigabit Fiber Network Connection [8086:1522] (rev 01)
fw 1.52.0
the SFP NICs no longer get link at all. Reverting commit a97f8783a9
or switching to the Intel out-of-tree driver both fix the problem.
Per the igb out-of-tree driver, I2C bit banging on i350 depends on
support for an external thermal sensor (ETS). However, commit
a97f8783a9 added bit banging unconditionally. Additionally, the
out-of-tree driver always calls init_thermal_sensor_thresh on probe,
while our driver only calls init_thermal_sensor_thresh only in
igb_reset(), and only if an ETS is present, ignoring the internal
thermal sensor. The affected SFPs don't provide an ETS. Per Intel,
the behaviour is a result of i350 firmware requirements.
This patch fixes the problem by aligning the behaviour to the
out-of-tree driver:
- split igb_init_i2c() into two functions:
- igb_init_i2c() only performs the basic I2C initialization.
- igb_set_i2c_bb() makes sure that E1000_CTRL_I2C_ENA is set
and enables bit-banging.
- igb_probe() only calls igb_set_i2c_bb() if an ETS is present.
- igb_probe() calls init_thermal_sensor_thresh() unconditionally.
- igb_reset() aligns its behaviour to igb_probe(), i. e., call
igb_set_i2c_bb() if an ETS is present and call
init_thermal_sensor_thresh() unconditionally.
Fixes: a97f8783a9 ("igb: unbreak I2C bit-banging on i350")
Tested-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Co-developed-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230214185549.1306522-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05d7623a89 upstream.
When setting 'snps,force_thresh_dma_mode' DT property, the following
warning is always emitted, regardless the status of force_sf_dma_mode:
dwmac-starfive 10020000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
Do not print the rather misleading message when DMA store and forward
mode is already disabled.
Fixes: e2a240c7d3 ("driver:net:stmmac: Disable DMA store and forward mode if platform data force_thresh_dma_mode is set.")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230210202126.877548-1-cristian.ciocaltea@collabora.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2038cc5928 upstream.
In bnxt_reserve_rings(), there is logic to check that the number of TX
rings reserved is enough to cover all the mqprio TCs, but it fails to
account for the TX XDP rings. So the check will always fail if there
are mqprio TCs and TX XDP rings. As a result, the driver always fails
to initialize after the XDP program is attached and the device will be
brought down. A subsequent ifconfig up will also fail because the
number of TX rings is set to an inconsistent number. Fix the check to
properly account for TX XDP rings. If the check fails, set the number
of TX rings back to a consistent number after calling netdev_reset_tc().
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4562c65ec8 upstream.
So far changing the period by just setting new period values while
running did not work.
The order as indicated by the publicly available reference manual of the i.MX8MP [1]
indicates a sequence:
* initiate the programming sequence
* set the values for PPS period and start time
* start the pulse train generation.
This is currently not used in dwmac5_flex_pps_config(), which instead does:
* initiate the programming sequence and immediately start the pulse train generation
* set the values for PPS period and start time
This caused the period values written not to take effect until the FlexPPS output was
disabled and re-enabled again.
This patch fix the order and allows the period to be set immediately.
[1] https://www.nxp.com/webapp/Download?colCode=IMX8MPRM
Fixes: 9a8a02c9d4 ("net: stmmac: Add Flexible PPS support")
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230210143937.3427483-1-j.zink@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c68f345b7c upstream.
syzbot reported that act_len in kalmia_send_init_packet() is
uninitialized when passing it to the first usb_bulk_msg error path. Jiri
Pirko noted that it's pointless to pass it in the error path, and that
the value that would be printed in the second error path would be the
value of act_len from the first call to usb_bulk_msg.[1]
With this in mind, let's just not pass act_len to the usb_bulk_msg error
paths.
1: https://lore.kernel.org/lkml/Y9pY61y1nwTuzMOa@nanopsycho/
Fixes: d40261236e ("net/usb: Add Samsung Kalmia driver for Samsung GT-B3730")
Reported-and-tested-by: syzbot+cd80c5ef5121bfe85b55@syzkaller.appspotmail.com
Signed-off-by: Miko Larsson <mikoxyzzz@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f09049417 upstream.
Incrementation of xsk_frames inside the for-loop produces
infinite loop, if we have both normal AF_XDP-TX and XDP_TXed
buffers to complete.
Split xsk_frames into 2 variables (xsk_frames and completed_frames)
to eliminate this bug.
Fixes: 29322791bc ("ice: xsk: change batched Tx descriptor cleaning")
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230209160130.1779890-1-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ed577e7e8 upstream.
In TI's AM62x/AM64x SoCs, successful teardown of RX DMA Channel raises an
interrupt. The process of servicing this interrupt involves flushing all
pending RX DMA descriptors and clearing the teardown completion marker
(TDCM). The am65_cpsw_nuss_rx_packets() function invoked from the RX
NAPI callback services the interrupt. Thus, it is necessary to wait for
this handler to run, drain all packets and clear TDCM, before calling
napi_disable() in am65_cpsw_nuss_common_stop() function post channel
teardown. If napi_disable() executes before ensuring that TDCM is
cleared, the TDCM remains set when the interfaces are down, resulting in
an interrupt storm when the interfaces are brought up again.
Since the interrupt raised to indicate the RX DMA Channel teardown is
specific to the AM62x and AM64x SoCs, add a quirk for it.
Fixes: 4f7cce2724 ("net: ethernet: ti: am65-cpsw: add support for am64x cpsw3g")
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230209084432.189222-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d61615c366 upstream.
Code blocks handling BCMA_CHIP_ID_BCM5357 and BCMA_CHIP_ID_BCM53572 were
incorrectly unified. Chip package values are not unique and cannot be
checked independently. They are meaningful only in a context of a given
chip.
Packages BCM5358 and BCM47188 share the same value but then belong to
different chips. Code unification resulted in treating BCM5358 as
BCM47188 and broke its initialization.
Link: https://github.com/openwrt/openwrt/issues/8278
Fixes: cb1b0f90ac ("net: ethernet: bgmac: unify code of the same family")
Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230208091637.16291-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce45ffb815 upstream.
Include the second VLAN HLEN into account when computing the maximum
MTU size as other drivers do.
Fixes: 0c8493d90b ("i40e: add XDP support for pass and drop actions")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9cd6a4418 upstream.
Recently I encountered one case where I cannot increase the MTU size
directly from 1500 to a much bigger value with XDP enabled if the
server is equipped with IXGBE card, which happened on thousands of
servers in production environment. After applying the current patch,
we can set the maximum MTU size to 3K.
This patch follows the behavior of changing MTU as i40e/ice does.
References:
[1] commit 23b44513c3 ("ice: allow 3k MTU for XDP")
[2] commit 0c8493d90b ("i40e: add XDP support for pass and drop actions")
Fixes: fabf1bce10 ("ixgbe: Prevent unsupported configurations with XDP")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43fbca02c2 upstream.
There was a problem reported to us where the addition of a VF with an IPv6
address ending with a particular sequence would cause the parent device on
the PF to no longer be able to respond to neighbor discovery packets.
In this case, we had an ovs-bridge device living on top of a VLAN, which
was on top of a PF, and it would not be able to talk anymore (the neighbor
entry would expire and couldn't be restored).
The root cause of the issue is that if the PF is asked to be in IFF_PROMISC
mode (promiscuous mode) and it had an ipv6 address that needed the
33:33:ff:00:00:04 multicast address to work, then when the VF was added
with the need for the same multicast address, the VF would steal all the
traffic destined for that address.
The ice driver didn't auto-subscribe a request of IFF_PROMISC to the
"multicast replication from other port's traffic" meaning that it won't get
for instance, packets with an exact destination in the VF, as above.
The VF's IPv6 address, which adds a "perfect filter" for 33:33:ff:00:00:04,
results in no packets for that multicast address making it to the PF (which
is in promisc but NOT "multicast replication").
The fix is to enable "multicast promiscuous" whenever the driver is asked
to enable IFF_PROMISC, and make sure to disable it when appropriate.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec76d0c2da upstream.
Commit b3973bb400 ("vmxnet3: set correct hash type based on
rss information") added hashType information into skb. However,
rssType field is populated for eop descriptor. This can lead
to incorrectly reporting of hashType for packets which use
multiple rx descriptors. Multiple rx descriptors are used
for Jumbo frame or LRO packets, which can hit this issue.
This patch moves the RSS codeblock under eop descritor.
Cc: stable@vger.kernel.org
Fixes: b3973bb400 ("vmxnet3: set correct hash type based on rss information")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Peng Li <lpeng@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Link: https://lore.kernel.org/r/20230208223900.5794-1-doshir@vmware.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3eceaed9e ]
There doesn't appear to be a reason to truncate the allocation used for
flow_info, so do a full allocation and remove the unused empty struct.
GCC does not like having a reference to an object that has been
partially allocated, as bounds checking may become impossible when
such an object is passed to other code. Seen with GCC 13:
../drivers/net/ethernet/mediatek/mtk_ppe.c: In function 'mtk_foe_entry_commit_subflow':
../drivers/net/ethernet/mediatek/mtk_ppe.c:623:18: warning: array subscript 'struct mtk_flow_entry[0]' is partly outside array bounds of 'unsigned char[48]' [-Warray-bounds=]
623 | flow_info->l2_data.base_flow = entry;
| ^~
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Mark Lee <Mark-MC.Lee@mediatek.com>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230127223853.never.014-kees@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54aa39a513 ]
Currently in phy_init_eee() the driver unconditionally configures the PHY
to stop RX_CLK after entering Rx LPI state. This causes an LPI interrupt
storm on my qcs404-base board.
Change the PHY initialization so that for "qcom,qcs404-ethqos" compatible
device RX_CLK continues to run even in Rx LPI state.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fcde9fe25 ]
While running this selftest which usually passes:
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
if I start PTP timestamping then run it again (debug prints added by me),
the unknown IPv6 MC traffic is seen by the CPU port even when it should
have been dropped:
~/selftests/drivers/net/dsa# ptp4l -i swp0 -2 -P -m
ptp4l[225.410]: selected /dev/ptp1 as PTP clock
[ 225.445746] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_add: port 0 adding L2 PTP trap
[ 225.453815] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP event trap
[ 225.462703] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP general trap
[ 225.471768] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP event trap
[ 225.480651] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP general trap
ptp4l[225.488]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[225.488]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
^C
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [FAIL]
reception succeeded, but should have failed
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
The PGID_MCIPV6 is configured correctly to not flood to the CPU,
I checked that.
Furthermore, when I disable back PTP RX timestamping (ptp4l doesn't do
that when it exists), packets are RX filtered again as they should be:
~/selftests/drivers/net/dsa# hwstamp_ctl -i swp0 -r 0
[ 218.202854] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_del: port 0 removing L2 PTP trap
[ 218.212656] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP event trap
[ 218.222975] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP general trap
[ 218.233133] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP event trap
[ 218.242251] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP general trap
current settings:
tx_type 1
rx_filter 12
new settings:
tx_type 1
rx_filter 0
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
So it's clear that something in the PTP RX trapping logic went wrong.
Looking a bit at the code, I can see that there are 4 typos, which
populate "ipv4" VCAP IS2 key filter fields for IPv6 keys.
VCAP IS2 keys of type OCELOT_VCAP_KEY_IPV4 and OCELOT_VCAP_KEY_IPV6 are
handled by is2_entry_set(). OCELOT_VCAP_KEY_IPV4 looks at
&filter->key.ipv4, and OCELOT_VCAP_KEY_IPV6 at &filter->key.ipv6.
Simply put, when we populate the wrong key field, &filter->key.ipv6
fields "proto.mask" and "proto.value" remain all zeroes (or "don't care").
So is2_entry_set() will enter the "else" of this "if" condition:
if (msk == 0xff && (val == IPPROTO_TCP || val == IPPROTO_UDP))
and proceed to ignore the "proto" field. The resulting rule will match
on all IPv6 traffic, trapping it to the CPU.
This is the reason why the local_termination.sh selftest sees it,
because control traps are stronger than the PGID_MCIPV6 used for
flooding (from the forwarding data path).
But the problem is in fact much deeper. We trap all IPv6 traffic to the
CPU, but if we're bridged, we set skb->offload_fwd_mark = 1, so software
forwarding will not take place and IPv6 traffic will never reach its
destination.
The fix is simple - correct the typos.
I was intentionally inaccurate in the commit message about the breakage
occurring when any PTP timestamping is enabled. In fact it only happens
when L4 timestamping is requested (HWTSTAMP_FILTER_PTP_V2_EVENT or
HWTSTAMP_FILTER_PTP_V2_L4_EVENT). But ptp4l requests a larger RX
timestamping filter than it needs for "-2": HWTSTAMP_FILTER_PTP_V2_EVENT.
I wanted people skimming through git logs to not think that the bug
doesn't affect them because they only use ptp4l in L2 mode.
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230207183117.1745754-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c966153d12 ]
Parameters 'queue_index' and 'napi_id' are passed in a swapped order.
Fix it here.
Fixes: 23233e577e ("net: ethernet: mtk_eth_soc: rely on page_pool for single page buffers")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b27517627 ]
On some platforms, 100/1000/2500 speeds seem to have sometimes problems
reporting false positive tx unit hang during stressful UDP traffic. Likely
other Intel drivers introduce responses to a tx hang. Update the 'tx hang'
comparator with the comparison of the head and tail of ring pointers and
restore the tx_timeout_factor to the previous value (one).
This can be test by using netperf or iperf3 applications.
Example:
iperf3 -s -p 5001
iperf3 -c 192.168.0.2 --udp -p 5001 --time 600 -b 0
netserver -p 16604
netperf -H 192.168.0.2 -l 600 -p 16604 -t UDP_STREAM -- -m 64000
Fixes: b27b8dc77b ("igc: Increase timeout value for Speed 100/1000/2500")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230206235818.662384-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f0d1451ec ]
Currently, remove and reload flows can run in parallel to module cleanup.
This design is error prone. For example: aux_drivers callbacks are called
from both cleanup and remove flows with different lockings, which can
cause a deadlock[1].
Hence, serialize module cleanup with reload and remove.
[1]
cleanup remove
------- ------
auxiliary_driver_unregister();
devl_lock()
auxiliary_device_delete(mlx5e_aux)
device_lock(mlx5e_aux)
devl_lock()
device_lock(mlx5e_aux)
Fixes: 912cebf420 ("net/mlx5e: Connect ethernet part to auxiliary bus")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 184e1e4474 ]
When tracer is reloaded, the device will log the traces at the
beginning of the log buffer. Also, driver is reading the log buffer in
chunks in accordance to the consumer index.
Hence, zero consumer index when reloading the tracer.
Fixes: 4383cfcc65 ("net/mlx5: Add devlink reload")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db561fed6b ]
Whenever the driver is reading the string DBs into buffers, the driver
is setting the load bit, but the driver never clears this bit.
As a result, in case load bit is on and the driver query the device for
new string DBs, the driver won't read again the string DBs.
Fix it by clearing the load bit when query the device for new string
DBs.
Fixes: 2d69356752 ("net/mlx5: Add support for fw live patch event")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9965bbebae ]
Currently, each core device has VF pages counter which stores number of
fw pages used by its VFs and SFs.
The current design led to a hang when performing firmware reset on DPU,
where the DPU PFs stalled in sriov unload flow due to waiting on release
of SFs pages instead of waiting on only VFs pages.
Thus, Add a separate counter for SF firmware pages, which will prevent
the stall scenario described above.
Fixes: 1958fc2f07 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3bdbaea65 ]
Currently, an independent page counter is used for tracking memory usage
for each function type such as VF, PF and host PF (DPU).
For better code-readibilty, use a single array that stores
the number of allocated memory pages for each function type.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 9965bbebae ("net/mlx5: Expose SF firmware pages counter")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aa5f171d5 ]
ethtool is returning an error for unknown speeds for the IPoIB interface:
$ ethtool ib0
netlink error: failed to retrieve link settings
netlink error: Invalid argument
netlink error: failed to retrieve link settings
netlink error: Invalid argument
Settings for ib0:
Link detected: no
After this change, ethtool will return success and show "unknown speed":
$ ethtool ib0
Settings for ib0:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Full
Auto-negotiation: off
Port: Other
PHYAD: 0
Transceiver: internal
Link detected: no
Fixes: eb234ee9d5 ("net/mlx5e: IPoIB, Add support for get_link_ksettings in ethtool")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8974aa9638 ]
Moving to switchdev mode with rx-vlan-filter on and then setting it off
causes the kernel to crash since fs->vlan is freed during nic profile
cleanup flow.
RX VLAN filtering is not supported in switchdev mode so unset it when
changing to switchdev and restore its value when switching back to
legacy.
trace:
[] RIP: 0010:mlx5e_disable_cvlan_filter+0x43/0x70
[] set_feature_cvlan_filter+0x37/0x40 [mlx5_core]
[] mlx5e_handle_feature+0x3a/0x60 [mlx5_core]
[] mlx5e_set_features+0x6d/0x160 [mlx5_core]
[] __netdev_update_features+0x288/0xa70
[] ethnl_set_features+0x309/0x380
[] ? __nla_parse+0x21/0x30
[] genl_family_rcv_msg_doit.isra.17+0x110/0x150
[] genl_rcv_msg+0x112/0x260
[] ? features_reply_size+0xe0/0xe0
[] ? genl_family_rcv_msg_doit.isra.17+0x150/0x150
[] netlink_rcv_skb+0x4e/0x100
[] genl_rcv+0x24/0x40
[] netlink_unicast+0x1ab/0x290
[] netlink_sendmsg+0x257/0x4f0
[] sock_sendmsg+0x5c/0x70
Fixes: cb67b83292 ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da0c52426c ]
SWITCHDEV_FDB_ADD_TO_BRIDGE event handler that updates FDB entry 'lastuse'
field is only executed for eswitch that owns the entry. However, if peer
entry processed packets at least once it will have hardware counter 'used'
value greater than entry 'lastuse' from that point on, which will cause FDB
entry not being aged out.
Process the event on all eswitch instances.
Fixes: ff9b752146 ("net/mlx5: Bridge, support LAG")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e66220948 ]
rq->hw_mtu is used in function en_rx.c/mlx5e_skb_from_cqe_mpwrq_linear()
to catch oversized packets. If FCS is concatenated to the end of the
packet then the check should be updated accordingly.
Rx rings initialization (mlx5e_init_rxq_rq()) invoked for every new set
of channels, as part of mlx5e_safe_switch_params(), unknowingly if it
runs with default configuration or not. Current rq->hw_mtu
initialization assumes default configuration and ignores
params->scatter_fcs_en flag state.
Fix this, by accounting for params->scatter_fcs_en flag state during
rq->hw_mtu initialization.
In addition, updating rq->hw_mtu value during ingress traffic might
lead to packets drop and oversize_pkts_sw_drop counter increase with no
good reason. Hence we remove this optimization and switch the set of
channels with a new one, to make sure we don't get false positives on
the oversize_pkts_sw_drop counter.
Fixes: 102722fc68 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Adham Faris <afaris@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f964f8399d ]
Alternative short title: don't instruct the hardware to match on
EtherType with "protocol 802.1Q" flower filters. It doesn't work for the
reasons detailed below.
With a command such as the following:
tc filter add dev $swp1 ingress chain $(IS1 2) pref 3 \
protocol 802.1Q flower skip_sw vlan_id 200 src_mac $h1_mac \
action vlan modify id 300 \
action goto chain $(IS2 0 0)
the created filter is set by ocelot_flower_parse_key() to be of type
OCELOT_VCAP_KEY_ETYPE, and etype is set to {value=0x8100, mask=0xffff}.
This gets propagated all the way to is1_entry_set() which commits it to
hardware (the VCAP_IS1_HK_ETYPE field of the key). Compare this to the
case where src_mac isn't specified - the key type is OCELOT_VCAP_KEY_ANY,
and is1_entry_set() doesn't populate VCAP_IS1_HK_ETYPE.
The problem is that for VLAN-tagged frames, the hardware interprets the
ETYPE field as holding the encapsulated VLAN protocol. So the above
filter will only match those packets which have an encapsulated protocol
of 0x8100, rather than all packets with VLAN ID 200 and the given src_mac.
The reason why this is allowed to occur is because, although we have a
block of code in ocelot_flower_parse_key() which sets "match_protocol"
to false when VLAN keys are present, that code executes too late.
There is another block of code, which executes for Ethernet addresses,
and has a "goto finished_key_parsing" and skips the VLAN header parsing.
By skipping it, "match_protocol" remains with the value it was
initialized with, i.e. "true", and "proto" is set to f->common.protocol,
or 0x8100.
The concept of ignoring some keys rather than erroring out when they are
present but can't be offloaded is dubious in itself, but is present
since the initial commit fe3490e610 ("net: mscc: ocelot: Hardware
ofload for tc flower filter"), and it's outside of the scope of this
patch to change that.
The problem was introduced when the driver started to interpret the
flower filter's protocol, and populate the VCAP filter's ETYPE field
based on it.
To fix this, it is sufficient to move the code that parses the VLAN keys
earlier than the "goto finished_key_parsing" instruction. This will
ensure that if we have a flower filter with both VLAN and Ethernet
address keys, it won't match on ETYPE 0x8100, because the VLAN key
parsing sets "match_protocol = false".
Fixes: 86b956de11 ("net: mscc: ocelot: support matching on EtherType")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230205192409.1796428-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b6d642510 ]
Frank reports that in a mt7530 setup where some ports are standalone and
some are in a VLAN-aware bridge, 8021q uppers of the standalone ports
lose their VLAN tag on xmit, as seen by the link partner.
This seems to occur because once the other ports join the VLAN-aware
bridge, mt7530_port_vlan_filtering() also calls
mt7530_port_set_vlan_aware(ds, cpu_dp->index), and this affects the way
that the switch processes the traffic of the standalone port.
Relevant is the PVC_EG_TAG bit. The MT7530 documentation says about it:
EG_TAG: Incoming Port Egress Tag VLAN Attribution
0: disabled (system default)
1: consistent (keep the original ingress tag attribute)
My interpretation is that this setting applies on the ingress port, and
"disabled" is basically the normal behavior, where the egress tag format
of the packet (tagged or untagged) is decided by the VLAN table
(MT7530_VLAN_EGRESS_UNTAG or MT7530_VLAN_EGRESS_TAG).
But there is also an option of overriding the system default behavior,
and for the egress tagging format of packets to be decided not by the
VLAN table, but simply by copying the ingress tag format (if ingress was
tagged, egress is tagged; if ingress was untagged, egress is untagged;
aka "consistent). This is useful in 2 scenarios:
- VLAN-unaware bridge ports will always encounter a miss in the VLAN
table. They should forward a packet as-is, though. So we use
"consistent" there. See commit e045124e93 ("net: dsa: mt7530: fix
tagged frames pass-through in VLAN-unaware mode").
- Traffic injected from the CPU port. The operating system is in god
mode; if it wants a packet to exit as VLAN-tagged, it sends it as
VLAN-tagged. Otherwise it sends it as VLAN-untagged*.
*This is true only if we don't consider the bridge TX forwarding offload
feature, which mt7530 doesn't support.
So for now, make the CPU port always stay in "consistent" mode to allow
software VLANs to be forwarded to their egress ports with the VLAN tag
intact, and not stripped.
Link: https://lore.kernel.org/netdev/trinity-e6294d28-636c-4c40-bb8b-b523521b00be-1674233135062@3c-app-gmx-bs36/
Fixes: e045124e93 ("net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230205140713.1609281-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a606ce684 ]
When ice_add_special_words() fails, the 'rm' is not released, which will
lead to a memory leak. Fix this up by going to 'err_unroll' label.
Compile tested only.
Fixes: 8b032a55c1 ("ice: low level support for tunnels")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c793f8ea15 ]
If the user turns on the vf-true-promiscuous-support flag, then Rx VLAN
filtering will be disabled if the VF requests to enable promiscuous
mode. When the VF is in a port VLAN, this is the incorrect behavior
because it will allow the VF to receive traffic outside of its port VLAN
domain. Fortunately this only resulted in the VF(s) receiving broadcast
traffic outside of the VLAN domain because all of the VLAN promiscuous
rules are based on the port VLAN ID. Fix this by setting the
.disable_rx_filtering VLAN op to a no-op when a port VLAN is enabled on
the VF.
Also, make sure to make this fix for both Single VLAN Mode and Double
VLAN Mode enabled devices.
Fixes: c31af68a1b ("ice: Add outer_vlan_ops and VSI specific VLAN ops implementations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7d94b2612 ]
Check all ports instead of just port_count ports. PTP init was only
checking ports 0 to port_count. If the hardware ports are not mapped
starting from 0 then they would be missed, e.g. if only ports 20-30 were
mapped it would attempt to init ports 0-10, resulting in NULL pointers
when attempting to timestamp. Now it will init all mapped ports.
Fixes: 70dfe25cd8 ("net: sparx5: Update extraction/injection for timestamping")
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b69585bfce ]
In one version of the HW there is a remote possibility that it
will miss the doorbell ring. This adds a bit of protection to
be sure we don't stall a queue from a missed doorbell.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Allen Hubbe <allen.hubbe@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e55f0f5bef ]
The same pre-work code is used before each call to
ionic_rx_fill(), so bring it in and make it a part of
the routine.
Signed-off-by: Neel Patel <neel@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: b69585bfce ("ionic: missed doorbell workaround")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8797a0584 ]
Clear the interrupt credits before enabling the queue rather
than after to be sure that the enabled queue starts at 0 and
that we don't wipe away possible credits after enabling the
queue.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Neel Patel <neel.patel@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69ff53e4a4 ]
Jerome provided the information that also the GXL internal PHY doesn't
support MMD register access and EEE. MMD reads return 0xffff, what
results in e.g. completely wrong ethtool --show-eee output.
Therefore use the MMD dummy stubs.
Fixes: d853d145ea ("net: phy: add an option to disable EEE advertisement")
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/84432fe4-0be4-bc82-4e5c-557206b40f56@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9011b028e ]
In zynqmp platforms where firmware supports dynamic SGMII configuration
but has other non-SGMII ethernet devices, it fails them with no packets
received at the RX interface.
To fix this behaviour perform SGMII dynamic configuration only
for the SGMII phy interface.
Fixes: 32cee78181 ("net: macb: Add zynqmp SGMII dynamic configuration support")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reported-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1675340779-27499-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbe83191d4 ]
Since commit ff9fb72bc0 ("debugfs: return error values,
not NULL") changed return value of debugfs_rename() in
error cases from %NULL to %ERR_PTR(-ERROR), we should
also check error values instead of NULL.
Fixes: ff9fb72bc0 ("debugfs: return error values, not NULL")
Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20230202093256.32458-1-zhengqi.arch@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce93fdb5f2 ]
After calling fwnode_phy_find_device(), the phy device refcount is
incremented. Then, when the phy device is attached to a netdev with
phy_attach_direct(), the refcount is also incremented but only
decremented in the caller if phy_attach_direct() fails. Move
phy_device_free() before the "if" to always release it correctly.
Indeed, either phy_attach_direct() failed and we don't want to keep a
reference to the phydev or it succeeded and a reference has been taken
internally.
Fixes: 25396f680d ("net: phylink: introduce phylink_fwnode_phy_connect()")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
