[ Upstream commit 47c428fce0 ]
Use "0x%x" format for quirks debug print to clarify it's a hexadecimal
value. Improves readability and consistency with other hex outputs.
Signed-off-by: Jiayi Li <lijiayi@kylinos.cn>
Link: https://lore.kernel.org/r/20250603071045.3243699-1-lijiayi@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5c98e8b13 ]
Pending requests will be flushed on disconnect, and the corresponding
TRBs will be turned into No-op TRBs, which are ignored by the xHC
controller once it starts processing the ring.
If the USB debug cable repeatedly disconnects before ring is started
then the ring will eventually be filled with No-op TRBs.
No new transfers can be queued when the ring is full, and driver will
print the following error message:
"xhci_hcd 0000:00:14.0: failed to queue trbs"
This is a normal case for 'in' transfers where TRBs are always enqueued
in advance, ready to take on incoming data. If no data arrives, and
device is disconnected, then ring dequeue will remain at beginning of
the ring while enqueue points to first free TRB after last cancelled
No-op TRB.
s
Solve this by reinitializing the rings when the debug cable disconnects
and DbC is leaving the configured state.
Clear the whole ring buffer and set enqueue and dequeue to the beginning
of ring, and set cycle bit to its initial state.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 220a0ffde0 ]
Decouple allocation of endpoint ring buffer from initialization
of the buffer, and initialization of endpoint context parts from
from the rest of the contexts.
It allows driver to clear up and reinitialize endpoint rings
after disconnect without reallocating everything.
This is a prerequisite for the next patch that prevents the transfer
ring from filling up with cancelled (no-op) TRBs if a debug cable is
reconnected several times without transferring anything.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d63c83d8e upstream.
Yunseong Kim and the syzbot fuzzer both reported a problem in
RT-enabled kernels caused by the way dummy-hcd mixes interrupt
management and spin-locking. The pattern was:
local_irq_save(flags);
spin_lock(&dum->lock);
...
spin_unlock(&dum->lock);
... // calls usb_gadget_giveback_request()
local_irq_restore(flags);
The code was written this way because usb_gadget_giveback_request()
needs to be called with interrupts disabled and the private lock not
held.
While this pattern works fine in non-RT kernels, it's not good when RT
is enabled. RT kernels handle spinlocks much like mutexes; in particular,
spin_lock() may sleep. But sleeping is not allowed while local
interrupts are disabled.
To fix the problem, rewrite the code to conform to the pattern used
elsewhere in dummy-hcd and other UDC drivers:
spin_lock_irqsave(&dum->lock, flags);
...
spin_unlock(&dum->lock);
usb_gadget_giveback_request(...);
spin_lock(&dum->lock);
...
spin_unlock_irqrestore(&dum->lock, flags);
This approach satisfies the RT requirements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Fixes: b4dbda1a22 ("USB: dummy-hcd: disable interrupts during req->complete")
Reported-by: Yunseong Kim <ysk@kzalloc.com>
Closes: <https://lore.kernel.org/linux-usb/5b337389-73b9-4ee4-a83e-7e82bf5af87a@kzalloc.com/>
Reported-by: syzbot+8baacc4139f12fa77909@syzkaller.appspotmail.com
Closes: <https://lore.kernel.org/linux-usb/68ac2411.050a0220.37038e.0087.GAE@google.com/>
Tested-by: syzbot+8baacc4139f12fa77909@syzkaller.appspotmail.com
CC: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
CC: stable@vger.kernel.org
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/bb192ae2-4eee-48ee-981f-3efdbbd0d8f0@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45eae113dc upstream.
This commit addresses a rarely observed endpoint command timeout
which causes kernel panic due to warn when 'panic_on_warn' is enabled
and unnecessary call trace prints when 'panic_on_warn' is disabled.
It is seen during fast software-controlled connect/disconnect testcases.
The following is one such endpoint command timeout that we observed:
1. Connect
=======
->dwc3_thread_interrupt
->dwc3_ep0_interrupt
->configfs_composite_setup
->composite_setup
->usb_ep_queue
->dwc3_gadget_ep0_queue
->__dwc3_gadget_ep0_queue
->__dwc3_ep0_do_control_data
->dwc3_send_gadget_ep_cmd
2. Disconnect
==========
->dwc3_thread_interrupt
->dwc3_gadget_disconnect_interrupt
->dwc3_ep0_reset_state
->dwc3_ep0_end_control_data
->dwc3_send_gadget_ep_cmd
In the issue scenario, in Exynos platforms, we observed that control
transfers for the previous connect have not yet been completed and end
transfer command sent as a part of the disconnect sequence and
processing of USB_ENDPOINT_HALT feature request from the host timeout.
This maybe an expected scenario since the controller is processing EP
commands sent as a part of the previous connect. It maybe better to
remove WARN_ON in all places where device endpoint commands are sent to
avoid unnecessary kernel panic due to warn.
Cc: stable <stable@kernel.org>
Co-developed-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250808125315.1607-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58577118cc upstream.
During a device-initiated disconnect, the End Transfer command resets
the event filter, allowing a new xferNotReady event to be generated
before the controller is fully halted. Processing this late event
incorrectly triggers a Start Transfer, which prevents the controller
from halting and results in a DSTS.DEVCTLHLT bit polling timeout.
Ignore the late xferNotReady event if the controller is already in a
disconnected state.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250807090700.2397190-1-khtsai@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98da66a70a upstream.
Since 'bcs->Residue' has the data type '__le32', convert it to the
correct byte order of the CPU using this driver when assigning it to
the local variable 'residue'.
Cc: stable <stable@kernel.org>
Fixes: 50a6cb932d ("USB: usb_storage: add ums-realtek driver")
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Link: https://lore.kernel.org/r/20250813145247.184717-3-thorsten.blum@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9420f4757 upstream.
Increase the External ROM access timeouts to prevent failures during
programming of External SPI EEPROM chips. The current timeouts are
too short for some SPI EEPROMs used with uPD720201 controllers.
The current timeout for Chip Erase in renesas_rom_erase() is 100 ms ,
the current timeout for Sector Erase issued by the controller before
Page Program in renesas_fw_download_image() is also 100 ms. Neither
timeout is sufficient for e.g. the Macronix MX25L5121E or MX25V5126F.
MX25L5121E reference manual [1] page 35 section "ERASE AND PROGRAMMING
PERFORMANCE" and page 23 section "Table 8. AC CHARACTERISTICS (Temperature
= 0°C to 70°C for Commercial grade, VCC = 2.7V ~ 3.6V)" row "tCE" indicate
that the maximum time required for Chip Erase opcode to complete is 2 s,
and for Sector Erase it is 300 ms .
MX25V5126F reference manual [2] page 47 section "13. ERASE AND PROGRAMMING
PERFORMANCE (2.3V - 3.6V)" and page 42 section "Table 8. AC CHARACTERISTICS
(Temperature = -40°C to 85°C for Industrial grade, VCC = 2.3V - 3.6V)" row
"tCE" indicate that the maximum time required for Chip Erase opcode to
complete is 3.2 s, and for Sector Erase it is 400 ms .
Update the timeouts such, that Chip Erase timeout is set to 5 seconds,
and Sector Erase timeout is set to 500 ms. Such lengthy timeouts ought
to be sufficient for majority of SPI EEPROM chips.
[1] https://www.macronix.com/Lists/Datasheet/Attachments/8634/MX25L5121E,%203V,%20512Kb,%20v1.3.pdf
[2] https://www.macronix.com/Lists/Datasheet/Attachments/8750/MX25V5126F,%202.5V,%20512Kb,%20v1.1.pdf
Fixes: 2478be82de ("usb: renesas-xhci: Add ROM loader for uPD720201")
Cc: stable <stable@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://lore.kernel.org/r/20250802225526.25431-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fe06185e1 upstream.
The USB core will unmap urb->transfer_dma after SETUP stage completes.
Then the USB controller will access unmapped memory when it received
device descriptor. If iommu is equipped, the entire test can't be
completed due to the memory accessing is blocked.
Fix it by calling map_urb_for_dma() again for IN stage. To reduce
redundant map for urb->transfer_buffer, this will also set
URB_NO_TRANSFER_DMA_MAP flag before first map_urb_for_dma() to skip
dma map for urb->transfer_buffer and clear URB_NO_TRANSFER_DMA_MAP
flag before second map_urb_for_dma().
Fixes: 216e0e563d ("usb: core: hcd: use map_urb_for_dma for single step set feature urb")
Cc: stable <stable@kernel.org>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250806083955.3325299-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e664036cf3 upstream.
Another SanDisk 3.2Gen1 Flash Drive also need DELAY_INIT quick,
or it will randomly work incorrectly on Huawei hisi platforms
when doing reboot test.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250801082728.469406-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 086a0e516f ]
Make sure to drop the reference to the dwc3 device taken by
of_find_device_by_node() on probe errors and on driver unbind.
Fixes: 6dd2565989 ("usb: dwc3: add imx8mp dwc3 glue layer driver")
Cc: stable@vger.kernel.org # 5.12
Cc: Li Jun <jun.li@nxp.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1473e9e767 ]
Make sure to drop the reference to the control device taken by
of_find_device_by_node() during probe when the driver is unbound.
Fixes: 8934d3e4d0 ("usb: musb: omap2430: Don't use omap_get_control_dev()")
Cc: stable@vger.kernel.org # 3.13
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb020bf522 ]
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230405141009.3400693-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 1473e9e767 ("usb: musb: omap2430: fix device leak at unbind")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1e61f6ab08 ]
This patch fixes a race condition communication error, which ends up in
PD hard resets when losing the race. Some systems, like the Radxa ROCK
5B are powered through USB-C without any backup power source and use a
FUSB302 chip to do the PD negotiation. This means it is quite important
to avoid hard resets, since that effectively kills the system's
power-supply.
I've found the following race condition while debugging unplanned power
loss during booting the board every now and then:
1. lots of TCPM/FUSB302/PD initialization stuff
2. TCPM ends up in SNK_WAIT_CAPABILITIES (tcpm_set_pd_rx is enabled here)
3. the remote PD source does not send anything, so TCPM does a SOFT RESET
4. TCPM ends up in SNK_WAIT_CAPABILITIES for the second time
(tcpm_set_pd_rx is enabled again, even though it is still on)
At this point I've seen broken CRC good messages being send by the
FUSB302 with a logic analyzer sniffing the CC lines. Also it looks like
messages are being lost and things generally going haywire with one of
the two sides doing a hard reset once a broken CRC good message was send
to the bus.
I think the system is running into a race condition, that the FIFOs are
being cleared and/or the automatic good CRC message generation flag is
being updated while a message is already arriving.
Let's avoid this by caching the PD RX enabled state, as we have already
processed anything in the FIFOs and are in a good state. As a side
effect that this also optimizes I2C bus usage :)
As far as I can tell the problem theoretically also exists when TCPM
enters SNK_WAIT_CAPABILITIES the first time, but I believe this is less
critical for the following reason:
On devices like the ROCK 5B, which are powered through a TCPM backed
USB-C port, the bootloader must have done some prior PD communication
(initial communication must happen within 5 seconds after plugging the
USB-C plug). This means the first time the kernel TCPM state machine
reaches SNK_WAIT_CAPABILITIES, the remote side is not sending messages
actively. On other devices a hard reset simply adds some extra delay and
things should be good afterwards.
Fixes: c034a43e72 ("staging: typec: Fairchild FUSB302 Type-c chip driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704-fusb302-race-condition-fix-v1-1-239012c0e27a@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Adjust context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93b400f495 upstream.
Make sure to drop the references taken to the child devices by
of_find_device_by_node() during probe on driver unbind.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Cc: stable@vger.kernel.org # 5.2
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20250724091910.21092-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 868837b0a9 upstream.
Make sure to drop the reference to the companion device taken during
probe when the driver is unbound.
Fixes: 39facfa01c ("usb: gadget: udc: renesas_usb3: Add register of usb role switch")
Cc: stable@vger.kernel.org # 4.19
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d1b02e5d7 upstream.
After a recent change in clang to expose uninitialized warnings from
const variables [1], there is a warning in cxacru_heavy_init():
drivers/usb/atm/cxacru.c:1104:6: error: variable 'bp' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
1104 | if (instance->modem_type->boot_rom_patch) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/atm/cxacru.c:1113:39: note: uninitialized use occurs here
1113 | cxacru_upload_firmware(instance, fw, bp);
| ^~
drivers/usb/atm/cxacru.c:1104:2: note: remove the 'if' if its condition is always true
1104 | if (instance->modem_type->boot_rom_patch) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/atm/cxacru.c:1095:32: note: initialize the variable 'bp' to silence this warning
1095 | const struct firmware *fw, *bp;
| ^
| = NULL
While the warning is technically correct that bp is conditionally passed
uninitialized to cxacru_upload_firmware(), it is ultimately a false
positive warning on the uninitialized use of bp because the same
condition that initializes bp, instance->modem_type->boot_rom_patch, is
the same one that gates the use of bp within cxacru_upload_firmware().
As this warning occurs in clang's frontend before inlining occurs, it
cannot know that these conditions are indentical to avoid the warning.
Manually inline cxacru_upload_firmware() into cxacru_heavy_init(), as
that is its only callsite, so that clang can see that bp is initialized
and used under the same condition, clearing up the warning without any
functional changes to the code (LLVM was already doing this inlining
later).
Cc: stable@vger.kernel.org
Fixes: 1b0e614652 ("[PATCH] USB ATM: driver for the Conexant AccessRunner chipset cxacru")
Closes: https://github.com/ClangBuiltLinux/linux/issues/2102
Link: 2464313eef [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20250722-usb-cxacru-fix-clang-21-uninit-warning-v2-1-6708a18decd2@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64690a90cd upstream.
On the devices that need their endpoints to get an
initial clear_halt, this needs to be done before
the devices can be opened. That means it needs to be
before the devices are registered.
Fixes: 15bf722e6f ("cdc-acm: Add support of ATOL FPrint fiscal printers")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250717141259.2345605-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7616f006db upstream.
The current power direction of an USB-C port also influences the
power_supply's online status, so a power role change should also update
the power_supply.
Fixes an issue on some systems where plugging in a normal USB device in
for the first time after a reboot will cause upower to erroneously
consider the system to be connected to AC power.
Cc: stable <stable@kernel.org>
Fixes: 0e6371fbfb ("usb: typec: ucsi: Report power supply changes")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250721-fix-ucsi-pwr-dir-notify-v1-1-e53d5340cb38@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf16f40836 upstream.
usb_parse_ss_endpoint_companion() checks descriptor type before length,
enabling a potentially odd read outside of the buffer size.
Fix this up by checking the size first before looking at any of the
fields in the descriptor.
Signed-off-by: Xinyu Liu <katieeliu@tencent.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 503bbde34c ]
Checking for the endpoint type is no reason for a WARN, as that can
cause a reboot. A driver not checking the endpoint type must not cause a
reboot, as there is just no point in this. We cannot prevent a device
from doing something incorrect as a reaction to a transfer. Hence
warning for a mere assumption being wrong is not sensible.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250612122149.2559724-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df9a825f33 ]
If pmc_usb_probe is called before SCU IPC is registered, pmc_usb_probe
will fail.
Return -EPROBE_DEFER when pmc_usb_probe doesn't get SCU IPC device, so
the probe function can be called again after SCU IPC is initialized.
Signed-off-by: Tomasz Michalec <tmichalec@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250610154058.1859812-1-tmichalec@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b9c60e440 ]
When a USB4 dock is unplugged from a system it won't respond to ring
events. The PCI core handles the surprise removal event and notifies
all PCI drivers. The XHCI PCI driver sets a flag that the device is
being removed as well.
When that flag is set don't show messages in the cleanup path for
marking the controller dead.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250717073107.488599-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f72b9aa821 ]
There is a subtle contradiction between sections of the xHCI 1.2 spec
regarding the initialization of Input Endpoint Context fields. Section
4.8.2 ("Endpoint Context Initialization") states that all fields should
be initialized to 0. However, Section 6.2.3 ("Endpoint Context", p.453)
specifies that the Average TRB Length (avg_trb_len) field shall be
greater than 0, and explicitly notes (p.454): "Software shall set
Average TRB Length to '8' for control endpoints."
Strictly setting all fields to 0 during initialization conflicts with
the specific recommendation for control endpoints. In practice, setting
avg_trb_len = 0 is not meaningful for the hardware/firmware, as the
value is used for bandwidth calculation.
Motivation: Our company is developing a custom Virtual xHC hardware
platform that strictly follows the xHCI spec and its recommendations.
During validation, we observed that enumeration fails and a parameter
error (TRB Completion Code = 5) is reported if avg_trb_len for EP0 is
not set to 8 as recommended by Section 6.2.3. This demonstrates the
importance of assigning a meaningful, non-zero value to avg_trb_len,
even in virtualized or emulated environments.
This patch explicitly sets avg_trb_len to 8 for EP0 in
xhci_setup_addressable_virt_dev(), as recommended in Section 6.2.3, to
prevent potential issues with xHCI host controllers that enforce the
spec strictly.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220033
Signed-off-by: Jay Chen <shawn2000100@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250717073107.488599-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65fc0fc137 ]
When a USB4 dock is unplugged from a system it won't respond to ring
events. The PCI core handles the surprise removal event and notifies
all PCI drivers. The XHCI PCI driver sets a flag that the device is
being removed, and when the device stops responding a flag is also
added to indicate it's dying.
When that flag is set don't bother to show warnings about a missing
controller.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250717073107.488599-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af833e7f7d ]
ucsi_psy_get_current_max would return 0mA as the maximum current if
UCSI detected a BC or a Default USB Power sporce.
The comment in this function is true that we can't tell the difference
between DCP/CDP or SDP chargers, but we can guarantee that at least 1-unit
of USB 1.1/2.0 power is available, which is 100mA, which is a better
fallback value than 0, which causes some userspaces, including the ChromeOS
power manager, to regard this as a power source that is not providing
any power.
In reality, 100mA is guaranteed from all sources in these classes.
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Jameson Thies <jthies@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250717200805.3710473-1-bleung@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7919407eca ]
When encounters some errors like these:
xhci_hcd 0000:4a:00.2: xHCI dying or halted, can't queue_command
xhci_hcd 0000:4a:00.2: FIXME: allocate a command ring segment
usb usb5-port6: couldn't allocate usb_device
It's hard to know whether xhc_state is dying or halted. So it's better
to print xhc_state's value which can help locate the resaon of the bug.
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20250725060117.1773770-1-suhui@nfschina.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 151c0aa896 upstream.
1. In func configfs_composite_bind() -> composite_os_desc_req_prepare():
if kmalloc fails, the pointer cdev->os_desc_req will be freed but not
set to NULL. Then it will return a failure to the upper-level function.
2. in func configfs_composite_bind() -> composite_dev_cleanup():
it will checks whether cdev->os_desc_req is NULL. If it is not NULL, it
will attempt to use it.This will lead to a use-after-free issue.
BUG: KASAN: use-after-free in composite_dev_cleanup+0xf4/0x2c0
Read of size 8 at addr 0000004827837a00 by task init/1
CPU: 10 PID: 1 Comm: init Tainted: G O 5.10.97-oh #1
kasan_report+0x188/0x1cc
__asan_load8+0xb4/0xbc
composite_dev_cleanup+0xf4/0x2c0
configfs_composite_bind+0x210/0x7ac
udc_bind_to_driver+0xb4/0x1ec
usb_gadget_probe_driver+0xec/0x21c
gadget_dev_desc_UDC_store+0x264/0x27c
Fixes: 37a3a53342 ("usb: gadget: OS Feature Descriptors support")
Cc: stable <stable@kernel.org>
Signed-off-by: Tao Xue <xuetao09@huawei.com>
Link: https://lore.kernel.org/r/20250721093908.14967-1-xuetao09@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 43007b89fb ]
When multiple Apple devices are connected concurrently, the
apple-mfi-fastcharge driver fails to probe the subsequent devices with
the following error:
sysfs: cannot create duplicate filename '/class/power_supply/apple_mfi_fastcharge'
apple-mfi-fastcharge 5-2.4.3.3: probe of 5-2.4.3.3 failed with error -17
This happens because the driver uses a fixed power supply name
("apple_mfi_fastcharge") for all devices, causing a sysfs name
conflict when a second device is connected.
Fix this by generating unique names using the USB bus and device
number (e.g., "apple_mfi_fastcharge_5-12"). This ensures each
connected device gets a unique power supply entry in sysfs.
The change requires storing a copy of the power_supply_desc structure
in the per-device mfi_device struct, since the name pointer needs to
remain valid for the lifetime of the power supply registration.
Fixes: 249fa8217b ("USB: Add driver to control USB fast charge for iOS devices")
Signed-off-by: Charalampos Mitrodimas <charmitro@posteo.net>
Link: https://lore.kernel.org/r/20250602-apple-mfi-fastcharge-duplicate-sysfs-v1-1-5d84de34fac6@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9e496a9fb ]
The variable `of_match` was incorrectly declared as a `bool`.
It is assigned the return value of of_match_device(), which is a pointer of
type `const struct of_device_id *`.
Fixes: 16b7e0cccb ("USB: xhci-plat: fix legacy PHY double init")
Signed-off-by: Seungjin Bae <eeodqql09@gmail.com>
Link: https://lore.kernel.org/r/20250619055746.176112-2-eeodqql09@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87ed257acb ]
For mxs PHY, if there is a vbus but the bus is not enumerated, we need
to force the dp/dm as SE0 from the controller side. If not, there is
possible USB wakeup due to unstable dp/dm, since there is possible no
pull on dp/dm, such as there is a USB charger on the port.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627110353.1879477-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7a62611fa ]
Add USB PHY event for below situation:
- usb role changed
- vbus connect
- vbus disconnect
- gadget driver is enumerated
USB PHY driver can get the last event after above situation occurs
and deal with different situations.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627110353.1879477-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bec15191d5 upstream.
This patch fixes Type-C compliance test TD 4.7.6 - Try.SNK DRP Connect
SNKAS.
tVbusON has a limit of 275ms when entering SRC_ATTACHED. Compliance
testers can interpret the TryWait.Src to Attached.Src transition after
Try.Snk as being in Attached.Src the entire time, so ~170ms is lost
to the debounce timer.
Setting the data role can be a costly operation in host mode, and when
completed after 100ms can cause Type-C compliance test check TD 4.7.5.V.4
to fail.
Turn VBUS on before tcpm_set_roles to meet timing requirement.
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250618230606.3272497-2-rdbabiera@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a50da8491 upstream.
The funciton tcpm_acc_attach is not setting the proper state when
calling tcpm_set_role. The function tcpm_set_role is currently only
handling TYPEC_STATE_USB. For the tcpm_acc_attach to switch into other
modal states tcpm_set_role needs to be extended by an extra state
parameter. This patch is handling the proper state change when calling
tcpm_acc_attach.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-3-b99f44badce8@pengutronix.de
Stable-dep-of: bec15191d5 ("usb: typec: tcpm: apply vbus before data bringup in tcpm_src_attach")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64843d0ba9 upstream.
Since the function tcpm_acc_attach is not setting the data and role for
for the sink case we extend it to check for it first.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-1-b99f44badce8@pengutronix.de
Stable-dep-of: bec15191d5 ("usb: typec: tcpm: apply vbus before data bringup in tcpm_src_attach")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef8abc0ba4 upstream.
Leaving the USB BCR asserted prevents the associated GDSC to turn on. This
blocks any subsequent attempts of probing the device, e.g. after a probe
deferral, with the following showing in the log:
[ 1.332226] usb30_prim_gdsc status stuck at 'off'
Leave the BCR deasserted when exiting the driver to avoid this issue.
Cc: stable <stable@kernel.org>
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250709132900.3408752-1-krishna.kurapati@oss.qualcomm.com
[ adapted to individual clock management API instead of bulk clock operations ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67a59f8219 upstream.
When unplugging the USB cable or disconnecting a gadget in usb peripheral mode with
echo "" > /sys/kernel/config/usb_gadget/<your_gadget>/UDC,
/sys/class/udc/musb-hdrc.0/state does not change from USB_STATE_CONFIGURED.
Testing on dwc2/3 shows they both update the state to USB_STATE_NOTATTACHED.
Add calls to usb_gadget_set_state in musb_g_disconnect and musb_gadget_stop
to fix both cases.
Fixes: 49401f4169 ("usb: gadget: introduce gadget state tracking")
Cc: stable@vger.kernel.org
Co-authored-by: Yehowshua Immanuel <yehowshua.immanuel@twosixtech.com>
Signed-off-by: Yehowshua Immanuel <yehowshua.immanuel@twosixtech.com>
Signed-off-by: Drew Hamilton <drew.hamilton@zetier.com>
Link: https://lore.kernel.org/r/20250701154126.8543-1-drew.hamilton@zetier.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21acc656a0 upstream.
Instead of manipulating musb->xceiv->otg->state directly, use the newly
introduced musb_get_state() and musb_set_state() inline functions.
Later, these inline functions will be modified to get rid of the
musb->xceiv dependency, which prevents the musb code from using the
generic PHY subsystem.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-2-paul@crapouillou.net
Stable-dep-of: 67a59f8219 ("usb: musb: fix gadget state on disconnect")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2521106fc7 upstream.
Hub driver warm-resets ports in SS.Inactive or Compliance mode to
recover a possible connected device. The port reset code correctly
detects if a connection is lost during reset, but hub driver
port_event() fails to take this into account in some cases.
port_event() ends up using stale values and assumes there is a
connected device, and will try all means to recover it, including
power-cycling the port.
Details:
This case was triggered when xHC host was suspended with DbC (Debug
Capability) enabled and connected. DbC turns one xHC port into a simple
usb debug device, allowing debugging a system with an A-to-A USB debug
cable.
xhci DbC code disables DbC when xHC is system suspended to D3, and
enables it back during resume.
We essentially end up with two hosts connected to each other during
suspend, and, for a short while during resume, until DbC is enabled back.
The suspended xHC host notices some activity on the roothub port, but
can't train the link due to being suspended, so xHC hardware sets a CAS
(Cold Attach Status) flag for this port to inform xhci host driver that
the port needs to be warm reset once xHC resumes.
CAS is xHCI specific, and not part of USB specification, so xhci driver
tells usb core that the port has a connection and link is in compliance
mode. Recovery from complinace mode is similar to CAS recovery.
xhci CAS driver support that fakes a compliance mode connection was added
in commit 8bea2bd37d ("usb: Add support for root hub port status CAS")
Once xHCI resumes and DbC is enabled back, all activity on the xHC
roothub host side port disappears. The hub driver will anyway think
port has a connection and link is in compliance mode, and hub driver
will try to recover it.
The port power-cycle during recovery seems to cause issues to the active
DbC connection.
Fix this by clearing connect_change flag if hub_port_reset() returns
-ENOTCONN, thus avoiding the whole unnecessary port recovery and
initialization attempt.
Cc: stable@vger.kernel.org
Fixes: 8bea2bd37d ("usb: Add support for root hub port status CAS")
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250623133947.3144608-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bd9c80263 upstream.
Delayed work that prevents USB3 hubs from runtime-suspending too early
needed to be flushed in hub_quiesce() to resolve issues detected on
QC SC8280XP CRD board during suspend resume testing.
This flushing did however trigger new issues on Raspberry Pi 3B+, which
doesn't have USB3 ports, and doesn't queue any post resume delayed work.
The flushed 'hub->init_work' item is used for several purposes, and
is originally initialized with a 'NULL' work function. The work function
is also changed on the fly, which may contribute to the issue.
Solve this by creating a dedicated delayed work item for post resume work,
and flush that delayed work in hub_quiesce()
Cc: stable <stable@kernel.org>
Fixes: a49e1e2e78 ("usb: hub: Fix flushing and scheduling of delayed work that tunes runtime pm")
Reported-by: Mark Brown <broonie@kernel.org>
Closes: https://lore.kernel.org/linux-usb/aF5rNp1l0LWITnEB@finisterre.sirena.org.uk
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # SC8280XP CRD
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250627164348.3982628-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a49e1e2e78 upstream.
Delayed work to prevent USB3 hubs from runtime-suspending immediately
after resume was added in commit 8f5b7e2bec ("usb: hub: fix detection
of high tier USB3 devices behind suspended hubs").
This delayed work needs be flushed if system suspends, or hub needs to
be quiesced for other reasons right after resume. Not flushing it
triggered issues on QC SC8280XP CRD board during suspend/resume testing.
Fix it by flushing the delayed resume work in hub_quiesce()
The delayed work item that allow hub runtime suspend is also scheduled
just before calling autopm get. Alan pointed out there is a small risk
that work is run before autopm get, which would call autopm put before
get, and mess up the runtime pm usage order.
Swap the order of work sheduling and calling autopm get to solve this.
Cc: stable <stable@kernel.org>
Fixes: 8f5b7e2bec ("usb: hub: fix detection of high tier USB3 devices behind suspended hubs")
Reported-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Closes: https://lore.kernel.org/linux-usb/acaaa928-832c-48ca-b0ea-d202d5cd3d6c@oss.qualcomm.com
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Closes: https://lore.kernel.org/linux-usb/c73fbead-66d7-497a-8fa1-75ea4761090a@rowland.harvard.edu
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250626130102.3639861-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f5b7e2bec upstream.
USB3 devices connected behind several external suspended hubs may not
be detected when plugged in due to aggressive hub runtime pm suspend.
The hub driver immediately runtime-suspends hubs if there are no
active children or port activity.
There is a delay between the wake signal causing hub resume, and driver
visible port activity on the hub downstream facing ports.
Most of the LFPS handshake, resume signaling and link training done
on the downstream ports is not visible to the hub driver until completed,
when device then will appear fully enabled and running on the port.
This delay between wake signal and detectable port change is even more
significant with chained suspended hubs where the wake signal will
propagate upstream first. Suspended hubs will only start resuming
downstream ports after upstream facing port resumes.
The hub driver may resume a USB3 hub, read status of all ports, not
yet see any activity, and runtime suspend back the hub before any
port activity is visible.
This exact case was seen when conncting USB3 devices to a suspended
Thunderbolt dock.
USB3 specification defines a 100ms tU3WakeupRetryDelay, indicating
USB3 devices expect to be resumed within 100ms after signaling wake.
if not then device will resend the wake signal.
Give the USB3 hubs twice this time (200ms) to detect any port
changes after resume, before allowing hub to runtime suspend again.
Cc: stable <stable@kernel.org>
Fixes: 2839f5bcfc ("USB: Turn on auto-suspend for USB 3.0 hubs.")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250611112441.2267883-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3014168731 upstream.
When writing an empty string to either 'qw_sign' or 'landingPage'
sysfs attributes, the store functions attempt to access page[l - 1]
before validating that the length 'l' is greater than zero.
This patch fixes the vulnerability by adding a check at the beginning
of os_desc_qw_sign_store() and webusb_landingPage_store() to handle
the zero-length input case gracefully by returning immediately.
Signed-off-by: Xinyu Liu <katieeliu@tencent.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/tencent_B1C9481688D0E95E7362AB2E999DE8048207@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c980666b69 upstream.
NDI (Northern Digital Inc.) is introducing a new product called the
EMGUIDE GEMINI that will use an FTDI chip for USB serial communications.
Add the NDI EMGUIDE GEMINI product ID that uses the NDI Vendor ID
rather than the FTDI Vendor ID, unlike older products.
Signed-off-by: Ryan Mann <rmann@ndigital.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
