[ Upstream commit db6c4dee4c ]
Add SolidRun vendor ID to pci_ids.h
The vendor ID is used in 2 different source files, the SNET vDPA driver
and PCI quirks.
Signed-off-by: Alvaro Karsz <alvaro.karsz@solid-run.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Message-Id: <20230110165638.123745-2-alvaro.karsz@solid-run.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a02426787 ]
The xtables packet traverser performs an unconditional local_bh_disable(),
but the nf_tables evaluation loop does not.
Functions that are called from either xtables or nftables must assume
that they can be called in process context.
inet_twsk_deschedule_put() assumes that no softirq interrupt can occur.
If tproxy is used from nf_tables its possible that we'll deadlock
trying to aquire a lock already held in process context.
Add a small helper that takes care of this and use it.
Link: https://lore.kernel.org/netfilter-devel/401bd6ed-314a-a196-1cdc-e13c720cc8f2@balasys.hu/
Fixes: 4ed8eb6570 ("netfilter: nf_tables: Add native tproxy support")
Reported-and-tested-by: Major Dávid <major.david@balasys.hu>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ddc761829 ]
state_lock, the spinlock type is meant to protect race against concurrent
MHI state transitions. In mhi_ep_set_m0_state(), while the state_lock is
being held, the channels are resumed in mhi_ep_resume_channels() if the
previous state was M3. This causes sleeping in atomic bug, since
mhi_ep_resume_channels() use mutex internally.
Since the state_lock is supposed to be held throughout the state change,
it is not ideal to drop the lock before calling mhi_ep_resume_channels().
So to fix this issue, let's change the type of state_lock to mutex. This
would also allow holding the lock throughout all state transitions thereby
avoiding any potential race.
Cc: <stable@vger.kernel.org> # 5.19
Fixes: e4b7b5f0f3 ("bus: mhi: ep: Add support for suspending and resuming channels")
Reported-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e01c4b7bd4 ]
This patch adds tracepoints for send and recv cases of dlm messages and
dlm rcom messages. In case of send and dlm message we add the dlm rsb
resource name this dlm messages belongs to. This has the advantage to
follow dlm messages on a per lock basis. In case of recv message the
resource name can be extracted by follow the send message sequence
number.
The dlm message DLM_MSG_PURGE doesn't belong to a lock request and will
not set the resource name in a dlm_message trace. The same for all rcom
messages.
There is additional handling required for this debugging functionality
which is tried to be small as possible. Also the midcomms layer gets
aware of lock resource names, for now this is required to make a
connection between sequence number and lock resource names. It is for
debugging purpose only.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Stable-dep-of: 724b6bab0d ("fs: dlm: fix use after free in midcomms commit")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b1a37ed00d upstream.
Presently, when a report is processed, its proposed size, provided by
the user of the API (as Report Size * Report Count) is compared against
the subsystem default HID_MAX_BUFFER_SIZE (16k). However, some
low-level HID drivers allocate a reduced amount of memory to their
buffers (e.g. UHID only allocates UHID_DATA_MAX (4k) buffers), rending
this check inadequate in some cases.
In these circumstances, if the received report ends up being smaller
than the proposed report size, the remainder of the buffer is zeroed.
That is, the space between sizeof(csize) (size of the current report)
and the rsize (size proposed i.e. Report Size * Report Count), which can
be handled up to HID_MAX_BUFFER_SIZE (16k). Meaning that memset()
shoots straight past the end of the buffer boundary and starts zeroing
out in-use values, often resulting in calamity.
This patch introduces a new variable into 'struct hid_ll_driver' where
individual low-level drivers can over-ride the default maximum value of
HID_MAX_BUFFER_SIZE (16k) with something more sympathetic to the
interface.
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ffdb67af0 upstream.
Add a function to get the old MST topology state, required by a
follow-up i915 patch.
While at it clarify the code comment of
drm_atomic_get_new_mst_topology_state() and add _new prefix
to the new state pointer to remind about its difference from the old
state.
v2: Use old_/new_ prefixes for the state pointers. (Ville)
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org # 6.1
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230206114856.2665066-3-imre.deak@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a2b9b123cc ]
Wangxun has verified there is no peer-to-peer between functions for the
below selection of SFxxx, RP1000 and RP2000 NICS. They may be
multi-function devices, but the hardware does not advertise ACS capability.
Add an ACS quirk for these devices so the functions can be in independent
IOMMU groups.
Link: https://lore.kernel.org/r/20230207102419.44326-1-mengyuanlou@net-swift.com
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e16cab9c15 ]
The color matching descriptors defined in the UVC Specification
contain 3 fields with discrete numeric values representing particular
settings. Enumerate those values so that later code setting them can
be more readable.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230202114142.300858-2-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b3517f88f ]
Except for isochronous-configured devices, software may set
Max_Read_Request_Size (MRRS) to any value up to 4096. If a device issues a
read request with size greater than the completer's Max_Payload_Size (MPS),
the completer is required to break the response into multiple completions.
Instead of correctly responding with multiple completions to a large read
request, some LS7A Root Ports respond with a Completer Abort. To prevent
this, the MRRS must be limited to an implementation-specific value.
The OS cannot detect that value, so rely on BIOS to configure MRRS before
booting, and quirk the Root Ports so we never set an MRRS larger than that
BIOS value for any downstream device.
N.B. Hot-added devices are not configured by BIOS, and they power up with
MRRS = 512 bytes, so these devices will be limited to 512 bytes. If the
LS7A limit is smaller, those hot-added devices may not work correctly, but
per [1], hotplug is not supported with this chipset revision.
[1] https://lore.kernel.org/r/073638a7-ae68-2847-ac3d-29e5e760d6af@loongson.cn
[bhelgaas: commit log]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216884
Link: https://lore.kernel.org/r/20230201043018.778499-3-chenhuacai@loongson.cn
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 015d44c2b7 ]
The Cypress EZUSB FX3 UVC example can be configured to report pixel
format "e436eb7e-524f-11ce-9f53-0020af0ba770". This is its GUID for
BGRA/X 8:8:8:8.
The UVC 1.5 spec [1] only defines GUIDs for YUY2, NV12, M420 and I420.
This seems to be an extension documented in the Microsoft Windows Media
Format SDK[2]. This Media Format SDK defines this GUID as corresponding
to `MEDIASUBTYPE_RGB32`, which is confirmed by [4] as `MEDIASUBTYPE_ARGB32`
has different GUID.
Note that in my case, the FX3 UVC can output either channel order,
BGR or RGB or any other mix for that matter. Since Linux commit
1b8dc32286 ("[media] uvcvideo: Add GUID for BGR 8:8:8")
defined a GUID for `MEDIASUBTYPE_RGB24` channel order as BGR, keep
this change consistent and define `MEDIASUBTYPE_RGB32` as BGR as well.
Document [3] also indicates the channel order is BGR.
[1] https://www.usb.org/document-library/video-class-v15-document-set
[2] https://learn.microsoft.com/en-us/windows/win32/wmformat/media-type-identifiers
[3] https://learn.microsoft.com/en-us/windows/win32/directshow/uncompressed-rgb-video-subtypes
[4] https://gix.github.io/media-types/
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ricardo@ribalda.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230126231456.3402323-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b839212988 ]
The memcpy() in uvc_video_decode_meta() intentionally copies across the
length and flags members and into the trailing buf flexible array.
Split the copy so that the compiler can better reason about (the lack
of) buffer overflows here. Avoid the run-time false positive warning:
memcpy: detected field-spanning write (size 12) of single field "&meta->length" at drivers/media/usb/uvc/uvc_video.c:1355 (size 1)
Additionally fix a typo in the documentation for struct uvc_meta_buf.
Reported-by: ionut_n2001@yahoo.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216810
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8133844a8f ]
It is questionable to allow a PCI bridge to go into D3 if it has _S0W
returning D2 or a shallower power state, so modify acpi_pci_bridge_d3(() to
always take the return value of _S0W for the target bridge into account.
That is, make it return 'false' if _S0W returns D2 or a shallower power
state for the target bridge regardless of its ancestor Root Port
properties. Of course, this also causes 'false' to be returned if the Root
Port itself is the target and its _S0W returns D2 or a shallower power
state.
However, still allow bridges without _S0W that are power-manageable via
ACPI to enter D3 to retain the current code behavior in that case.
This fixes problems where a hotplug notification is missed because a bridge
is in D3. That means hot-added devices such as USB4 docks (and the devices
they contain) and Thunderbolt 3 devices may not work.
Link: https://lore.kernel.org/linux-pci/20221031223356.32570-1-mario.limonciello@amd.com/
Link: https://lore.kernel.org/r/12155458.O9o76ZdvQC@kreacher
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c40624930 ]
The Data Capture and Compare(DCC) is a debugging tool that uses the bootconfig
for configuring the register values during boot-time. Increase the max nodes
supported by bootconfig to cater to the requirements of the Data Capture and
Compare Driver.
Link: https://lore.kernel.org/all/1674536682-18404-1-git-send-email-quic_schowdhu@quicinc.com/
Signed-off-by: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0322ef49c1 ]
During the refactoring in the commit below, vsc9953_mdio_read() was
replaced with mscc_miim_read(), which has one extra step: it checks for
the MSCC_MIIM_DATA_ERROR bits before returning the result.
On T1040RDB, there are 8 QSGMII PCSes belonging to the switch, and they
are organized in 2 groups. First group responds to MDIO addresses 4-7
because QSGMIIACR1[MDEV_PORT] is 1, and the second group responds to
MDIO addresses 8-11 because QSGMIIBCR1[MDEV_PORT] is 2. I have double
checked that these values are correctly set in the SERDES, as well as
PCCR1[QSGMA_CFG] and PCCR1[QSGMB_CFG] are both 0b01.
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 4 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 4 reg 0x5 MIIM_DATA 0x3da01, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
As can be seen, the data in MIIM_DATA is still valid despite having the
MSCC_MIIM_DATA_ERROR bits set. The driver as introduced in commit
84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953
switch") was ignoring these bits, perhaps deliberately (although
unbeknownst to me).
This is an old IP and the hardware team cannot seem to be able to help
me track down a plausible reason for these failures. I'll keep
investigating, but in the meantime, this is a direct regression which
must be restored to a working state.
The only thing I can do is keep ignoring the errors as before.
Fixes: b996584523 ("net: dsa: ocelot: felix: utilize shared mscc-miim driver for indirect MDIO access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52cf89f78c ]
The software pedit action didn't get the same love as some of the
other actions and it's still using spinlocks and shared stats in the
datapath.
Transition the action to rcu and percpu stats as this improves the
action's performance dramatically on multiple cpu deployments.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: e9e42292ea ("net/sched: act_pedit: fix action bind logic")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68ba446395 ]
With this refcnt added in sctp_stream_priorities, we don't need to
traverse all streams to check if the prio is used by other streams
when freeing one stream's prio in sctp_sched_prio_free_sid(). This
can avoid a nested loop (up to 65535 * 65535), which may cause a
stuck as Ying reported:
watchdog: BUG: soft lockup - CPU#23 stuck for 26s! [ksoftirqd/23:136]
Call Trace:
<TASK>
sctp_sched_prio_free_sid+0xab/0x100 [sctp]
sctp_stream_free_ext+0x64/0xa0 [sctp]
sctp_stream_free+0x31/0x50 [sctp]
sctp_association_free+0xa5/0x200 [sctp]
Note that it doesn't need to use refcount_t type for this counter,
as its accessing is always protected under the sock lock.
v1->v2:
- add a check in sctp_sched_prio_set to avoid the possible prio_head
refcnt overflow.
Fixes: 9ed7bfc795 ("sctp: fix memory leak in sctp_stream_outq_migrate()")
Reported-by: Ying Xu <yinxu@redhat.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/825eb0c905cb864991eba335f4a2b780e543f06b.1677085641.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdf6491193 ]
pernet tracking doesn't work correctly because other netns might have
set NETLINK_LISTEN_ALL_NSID on its event socket.
In this case its expected that events originating in other net
namespaces are also received.
Making pernet-tracking work while also honoring NETLINK_LISTEN_ALL_NSID
requires much more intrusive changes both in netlink and nfnetlink,
f.e. adding a 'setsockopt' callback that lets nfnetlink know that the
event socket entered (or left) ALL_NSID mode.
Move to global tracking instead: if there is an event socket anywhere
on the system, all net namespaces which have conntrack enabled and
use autobind mode will allocate the ecache extension.
netlink_has_listeners() returns false only if the given group has no
subscribers in any net namespace, the 'net' argument passed to
nfnetlink_has_listeners is only used to derive the protocol (nfnetlink),
it has no other effect.
For proper NETLINK_LISTEN_ALL_NSID-aware pernet tracking of event
listeners a new netlink_has_net_listeners() is also needed.
Fixes: 90d1daa458 ("netfilter: conntrack: add nf_conntrack_events autodetect mode")
Reported-by: Bryce Kahle <bryce.kahle@datadoghq.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f3a9ae990 ]
Commit 3db1de0e58 ("f2fs: change the current atomic write way")
removed old tracepoints, but it missed to add new one, this patch
fixes to introduce trace_f2fs_replace_atomic_write_block to trace
atomic_write commit flow.
Fixes: 3db1de0e58 ("f2fs: change the current atomic write way")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51de3fc9a8 ]
The rpcif structure is used as a common data structure, shared by the
RPC-IF core driver and by the HyperBus and SPI child drivers.
This poses several problems:
- Most structure members describe private core driver state, which
should not be accessible by the child drivers,
- The structure's lifetime is controlled by the child drivers,
complicating use by the core driver.
Fix this by moving the private core driver state to its own structure,
managed by the RPC-IF core driver, and store it in the core driver's
private data field. This requires absorbing the child's platform
device, as that was stored in the driver's private data field before.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/09fbb6fa67d5a8cd48a08808c9afa2f6a499aa42.1669213027.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 81c1188905 which is
commit f1c006f1c6 upstream.
It is reported to cause problems, as only 2 of the 3 patch series were
applied to the stable branches.
Reported-by: Mike Cloaked <mike.cloaked@gmail.com>
Reported-by: Eric Biggers <ebiggers@kernel.org>
Cc: Yu Kuai <yukuai3@huawei.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Sasha Levin <sashal@kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217174
Link: https://lore.kernel.org/r/ZAuPkCn49urWBN5P@sol.localdomain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee7dc86b6d upstream.
Sbitmap code will need to know how many waiters were actually woken for
its batched wakeups implementation. Return the number of woken
exclusive waiters from __wake_up() to facilitate that.
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Gabriel Krisman Bertazi <krisman@suse.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20221115224553.23594-3-krisman@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef3a3f6a29 upstream.
Disable the VFIO_UPDATE_VADDR capability if mediated devices are present.
Their kernel threads could be blocked indefinitely by a misbehaving
userland while trying to pin/unpin pages while vaddrs are being updated.
Do not allow groups to be added to the container while vaddr's are invalid,
so we never need to block user threads from pinning, and can delete the
vaddr-waiting code in a subsequent patch.
Fixes: c3cbab24db ("vfio/type1: implement interfaces to update vaddr")
Cc: stable@vger.kernel.org
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/1675184289-267876-2-git-send-email-steven.sistare@oracle.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6da6b1d4a7 upstream.
After a memory error happens on a clean folio, a process unexpectedly
receives SIGBUS when it accesses the error page. This SIGBUS killing is
pointless and simply degrades the level of RAS of the system, because the
clean folio can be dropped without any data lost on memory error handling
as we do for a clean pagecache.
When memory_failure() is called on a clean folio, try_to_unmap() is called
twice (one from split_huge_page() and one from hwpoison_user_mappings()).
The root cause of the issue is that pte conversion to hwpoisoned entry is
now done in the first call of try_to_unmap() because PageHWPoison is
already set at this point, while it's actually expected to be done in the
second call. This behavior disturbs the error handling operation like
removing pagecache, which results in the malfunction described above.
So convert TTU_IGNORE_HWPOISON into TTU_HWPOISON and set TTU_HWPOISON only
when we really intend to convert pte to hwpoison entry. This can prevent
other callers of try_to_unmap() from accidentally converting to hwpoison
entries.
Link: https://lkml.kernel.org/r/20230221085905.1465385-1-naoya.horiguchi@linux.dev
Fixes: a42634a6c0 ("readahead: Use a folio in read_pages()")
Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f57aec443c upstream.
A loop of the form:
while true; do modprobe cxl_pci; modprobe -r cxl_pci; done
...fails with the following crash signature:
BUG: kernel NULL pointer dereference, address: 0000000000000040
[..]
RIP: 0010:cxl_internal_send_cmd+0x5/0xb0 [cxl_core]
[..]
Call Trace:
<TASK>
cxl_pmem_ctl+0x121/0x240 [cxl_pmem]
nvdimm_get_config_data+0xd6/0x1a0 [libnvdimm]
nd_label_data_init+0x135/0x7e0 [libnvdimm]
nvdimm_probe+0xd6/0x1c0 [libnvdimm]
nvdimm_bus_probe+0x7a/0x1e0 [libnvdimm]
really_probe+0xde/0x380
__driver_probe_device+0x78/0x170
driver_probe_device+0x1f/0x90
__device_attach_driver+0x85/0x110
bus_for_each_drv+0x7d/0xc0
__device_attach+0xb4/0x1e0
bus_probe_device+0x9f/0xc0
device_add+0x445/0x9c0
nd_async_device_register+0xe/0x40 [libnvdimm]
async_run_entry_fn+0x30/0x130
...namely that the bottom half of async nvdimm device registration runs
after the CXL has already torn down the context that cxl_pmem_ctl()
needs. Unlike the ACPI NFIT case that benefits from launching multiple
nvdimm device registrations in parallel from those listed in the table,
CXL is already marked PROBE_PREFER_ASYNCHRONOUS. So provide for a
synchronous registration path to preclude this scenario.
Fixes: 21083f5152 ("cxl/pmem: Register 'pmem' / cxl_nvdimm devices")
Cc: <stable@vger.kernel.org>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4971c268b8 upstream.
Commit 98de59bfe4 ("take calculation of final prot in
security_mmap_file() into a helper") moved the code to update prot, to be
the actual protections applied to the kernel, to a new helper called
mmap_prot().
However, while without the helper ima_file_mmap() was getting the updated
prot, with the helper ima_file_mmap() gets the original prot, which
contains the protections requested by the application.
A possible consequence of this change is that, if an application calls
mmap() with only PROT_READ, and the kernel applies PROT_EXEC in addition,
that application would have access to executable memory without having this
event recorded in the IMA measurement list. This situation would occur for
example if the application, before mmap(), calls the personality() system
call with READ_IMPLIES_EXEC as the first argument.
Align ima_file_mmap() parameters with those of the mmap_file LSM hook, so
that IMA can receive both the requested prot and the final prot. Since the
requested protections are stored in a new variable, and the final
protections are stored in the existing variable, this effectively restores
the original behavior of the MMAP_CHECK hook.
Cc: stable@vger.kernel.org
Fixes: 98de59bfe4 ("take calculation of final prot in security_mmap_file() into a helper")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1c97a1b4e upstream.
When arch_prepare_optimized_kprobe calculating jump destination address,
it copies original instructions from jmp-optimized kprobe (see
__recover_optprobed_insn), and calculated based on length of original
instruction.
arch_check_optimized_kprobe does not check KPROBE_FLAG_OPTIMATED when
checking whether jmp-optimized kprobe exists.
As a result, setup_detour_execution may jump to a range that has been
overwritten by jump destination address, resulting in an inval opcode error.
For example, assume that register two kprobes whose addresses are
<func+9> and <func+11> in "func" function.
The original code of "func" function is as follows:
0xffffffff816cb5e9 <+9>: push %r12
0xffffffff816cb5eb <+11>: xor %r12d,%r12d
0xffffffff816cb5ee <+14>: test %rdi,%rdi
0xffffffff816cb5f1 <+17>: setne %r12b
0xffffffff816cb5f5 <+21>: push %rbp
1.Register the kprobe for <func+11>, assume that is kp1, corresponding optimized_kprobe is op1.
After the optimization, "func" code changes to:
0xffffffff816cc079 <+9>: push %r12
0xffffffff816cc07b <+11>: jmp 0xffffffffa0210000
0xffffffff816cc080 <+16>: incl 0xf(%rcx)
0xffffffff816cc083 <+19>: xchg %eax,%ebp
0xffffffff816cc084 <+20>: (bad)
0xffffffff816cc085 <+21>: push %rbp
Now op1->flags == KPROBE_FLAG_OPTIMATED;
2. Register the kprobe for <func+9>, assume that is kp2, corresponding optimized_kprobe is op2.
register_kprobe(kp2)
register_aggr_kprobe
alloc_aggr_kprobe
__prepare_optimized_kprobe
arch_prepare_optimized_kprobe
__recover_optprobed_insn // copy original bytes from kp1->optinsn.copied_insn,
// jump address = <func+14>
3. disable kp1:
disable_kprobe(kp1)
__disable_kprobe
...
if (p == orig_p || aggr_kprobe_disabled(orig_p)) {
ret = disarm_kprobe(orig_p, true) // add op1 in unoptimizing_list, not unoptimized
orig_p->flags |= KPROBE_FLAG_DISABLED; // op1->flags == KPROBE_FLAG_OPTIMATED | KPROBE_FLAG_DISABLED
...
4. unregister kp2
__unregister_kprobe_top
...
if (!kprobe_disabled(ap) && !kprobes_all_disarmed) {
optimize_kprobe(op)
...
if (arch_check_optimized_kprobe(op) < 0) // because op1 has KPROBE_FLAG_DISABLED, here not return
return;
p->kp.flags |= KPROBE_FLAG_OPTIMIZED; // now op2 has KPROBE_FLAG_OPTIMIZED
}
"func" code now is:
0xffffffff816cc079 <+9>: int3
0xffffffff816cc07a <+10>: push %rsp
0xffffffff816cc07b <+11>: jmp 0xffffffffa0210000
0xffffffff816cc080 <+16>: incl 0xf(%rcx)
0xffffffff816cc083 <+19>: xchg %eax,%ebp
0xffffffff816cc084 <+20>: (bad)
0xffffffff816cc085 <+21>: push %rbp
5. if call "func", int3 handler call setup_detour_execution:
if (p->flags & KPROBE_FLAG_OPTIMIZED) {
...
regs->ip = (unsigned long)op->optinsn.insn + TMPL_END_IDX;
...
}
The code for the destination address is
0xffffffffa021072c: push %r12
0xffffffffa021072e: xor %r12d,%r12d
0xffffffffa0210731: jmp 0xffffffff816cb5ee <func+14>
However, <func+14> is not a valid start instruction address. As a result, an error occurs.
Link: https://lore.kernel.org/all/20230216034247.32348-3-yangjihong1@huawei.com/
Fixes: f66c0447cc ("kprobes: Set unoptimized flag after unoptimizing code")
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Cc: stable@vger.kernel.org
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 868a6fc0ca upstream.
Since the following commit:
commit f66c0447cc ("kprobes: Set unoptimized flag after unoptimizing code")
modified the update timing of the KPROBE_FLAG_OPTIMIZED, a optimized_kprobe
may be in the optimizing or unoptimizing state when op.kp->flags
has KPROBE_FLAG_OPTIMIZED and op->list is not empty.
The __recover_optprobed_insn check logic is incorrect, a kprobe in the
unoptimizing state may be incorrectly determined as unoptimizing.
As a result, incorrect instructions are copied.
The optprobe_queued_unopt function needs to be exported for invoking in
arch directory.
Link: https://lore.kernel.org/all/20230216034247.32348-2-yangjihong1@huawei.com/
Fixes: f66c0447cc ("kprobes: Set unoptimized flag after unoptimizing code")
Cc: stable@vger.kernel.org
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36632d0629 upstream.
Zero-length arrays are deprecated[1]. Replace struct io_uring_buf_ring's
"bufs" with a flexible array member. (How is the size of this array
verified?) Detected with GCC 13, using -fstrict-flex-arrays=3:
In function 'io_ring_buffer_select',
inlined from 'io_buffer_select' at io_uring/kbuf.c:183:10:
io_uring/kbuf.c:141:23: warning: array subscript 255 is outside the bounds of an interior zero-length array 'struct io_uring_buf[0]' [-Wzero-length-bounds]
141 | buf = &br->bufs[head];
| ^~~~~~~~~~~~~~~
In file included from include/linux/io_uring.h:7,
from io_uring/kbuf.c:10:
include/uapi/linux/io_uring.h: In function 'io_buffer_select':
include/uapi/linux/io_uring.h:628:41: note: while referencing 'bufs'
628 | struct io_uring_buf bufs[0];
| ^~~~
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
Fixes: c7fb19428d ("io_uring: add support for ring mapped supplied buffers")
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: stable@vger.kernel.org
Cc: io-uring@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230105190507.gonna.131-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d987150b53 ]
[why & how]
__drm_dbg() parameter set format is wrong and not aligned with the
format under CONFIG_DRM_USE_DYNAMIC_DEBUG is on. Fix it.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0ab772c1f ]
Fix a bug in trace point definition for devlink health report, as
TP_STRUCT_entry of reporter_name should get reporter_name and not msg.
Note no fixes tag as this is a harmless bug as both reporter_name and
msg are strings and TP_fast_assign for this entry is correct.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04ffde1319 ]
While there is logic about the difference between ksize and usize,
copy_struct_from_user() didn't check the size of the destination buffer
(when it was known) against ksize. Add this check so there is an upper
bounds check on the possible memset() call, otherwise lower bounds
checks made by callers will trigger bounds warnings under -Warray-bounds.
Seen under GCC 13:
In function 'copy_struct_from_user',
inlined from 'iommufd_fops_ioctl' at
../drivers/iommu/iommufd/main.c:333:8:
../include/linux/fortify-string.h:59:33: warning: '__builtin_memset' offset [57, 4294967294] is out of the bounds [0, 56] of object 'buf' with type 'union ucmd_buffer' [-Warray-bounds=]
59 | #define __underlying_memset __builtin_memset
| ^
../include/linux/fortify-string.h:453:9: note: in expansion of macro '__underlying_memset'
453 | __underlying_memset(p, c, __fortify_size); \
| ^~~~~~~~~~~~~~~~~~~
../include/linux/fortify-string.h:461:25: note: in expansion of macro '__fortify_memset_chk'
461 | #define memset(p, c, s) __fortify_memset_chk(p, c, s, \
| ^~~~~~~~~~~~~~~~~~~~
../include/linux/uaccess.h:334:17: note: in expansion of macro 'memset'
334 | memset(dst + size, 0, rest);
| ^~~~~~
../drivers/iommu/iommufd/main.c: In function 'iommufd_fops_ioctl':
../drivers/iommu/iommufd/main.c:311:27: note: 'buf' declared here
311 | union ucmd_buffer buf;
| ^~~
Cc: Christian Brauner <brauner@kernel.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alexander Potapenko <glider@google.com>
Acked-by: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/lkml/20230203193523.never.667-kees@kernel.org/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cae5ded53 ]
Currently, RCU_LOCKDEP_WARN() checks the condition before checking
to see if lockdep is still enabled. This is necessary to avoid the
false-positive splats fixed by commit 3066820034 ("rcu: Reject
RCU_LOCKDEP_WARN() false positives"). However, the current state can
result in false-positive splats during early boot before lockdep is fully
initialized. This commit therefore checks debug_lockdep_rcu_enabled()
both before and after checking the condition, thus avoiding both sets
of false-positive error reports.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a5d7e9bad ]
In order to avoid WARN/BUG from generating nested or even recursive
warnings, force rcu_is_watching() true during
WARN/lockdep_rcu_suspicious().
Notably things like unwinding the stack can trigger rcu_dereference()
warnings, which then triggers more unwinding which then triggers more
warnings etc..
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230126151323.408156109@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1c006f1c6 ]
Currently parent pd can be freed before child pd:
t1: remove cgroup C1
blkcg_destroy_blkgs
blkg_destroy
list_del_init(&blkg->q_node)
// remove blkg from queue list
percpu_ref_kill(&blkg->refcnt)
blkg_release
call_rcu
t2: from t1
__blkg_release
blkg_free
schedule_work
t4: deactivate policy
blkcg_deactivate_policy
pd_free_fn
// parent of C1 is freed first
t3: from t2
blkg_free_workfn
pd_free_fn
If policy(for example, ioc_timer_fn() from iocost) access parent pd from
child pd after pd_offline_fn(), then UAF can be triggered.
Fix the problem by delaying 'list_del_init(&blkg->q_node)' from
blkg_destroy() to blkg_free_workfn(), and using a new disk level mutex to
synchronize blkg_free_workfn() and blkcg_deactivate_policy().
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230119110350.2287325-4-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47d586913f ]
Currently, filp_close() and generic_shutdown_super() use printk() to log
messages when bugs are detected. This is problematic because infrastructure
like syzkaller has no idea that this message indicates a bug.
In addition, some people explicitly want their kernels to BUG() when kernel
data corruption has been detected (CONFIG_BUG_ON_DATA_CORRUPTION).
And finally, when generic_shutdown_super() detects remaining inodes on a
system without CONFIG_BUG_ON_DATA_CORRUPTION, it would be nice if later
accesses to a busy inode would at least crash somewhat cleanly rather than
walking through freed memory.
To address all three, use CHECK_DATA_CORRUPTION() when kernel bugs are
detected.
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd115c0409 ]
Consolidate the code that computes the flags to be used when creating a
device link from a fwnode link.
Fixes: 2de9d8e0d2 ("driver core: fw_devlink: Improve handling of cyclic dependencies")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-8-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a6dfdf8b3 ]
To improve detection and handling of dependency cycles, we need to be
able to mark fwnode links as being part of cycles. fwnode links marked
as being part of a cycle should not block their consumers from probing.
Fixes: 2de9d8e0d2 ("driver core: fw_devlink: Improve handling of cyclic dependencies")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-7-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67cad5c670 ]
fw_devlink uses DL_FLAG_SYNC_STATE_ONLY device link flag for two
purposes:
1. To allow a parent device to proxy its child device's dependency on a
supplier so that the supplier doesn't get its sync_state() callback
before the child device/consumer can be added and probed. In this
usage scenario, we need to ignore cycles for ensure correctness of
sync_state() callbacks.
2. When there are dependency cycles in firmware, we don't know which of
those dependencies are valid. So, we have to ignore them all wrt
probe ordering while still making sure the sync_state() callbacks
come correctly.
However, when detecting dependency cycles, there can be multiple
dependency cycles between two devices that we need to detect. For
example:
A -> B -> A and A -> C -> B -> A.
To detect multiple cycles correct, we need to be able to differentiate
DL_FLAG_SYNC_STATE_ONLY device links used for (1) vs (2) above.
To allow this differentiation, add a DL_FLAG_CYCLE that can be use to
mark use case (2). We can then use the DL_FLAG_CYCLE to decide which
DL_FLAG_SYNC_STATE_ONLY device links to follow when looking for
dependency cycles.
Fixes: 2de9d8e0d2 ("driver core: fw_devlink: Improve handling of cyclic dependencies")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-6-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a863678038 ]
Current some drivers(like iscsi) call transport_register_device()
failed, they don't call transport_destroy_device() to release the
memory allocated in transport_setup_device(), because they don't
know what was done, it should be internal thing to release the
resource in register function. So fix this leak by calling destroy
function inside register function.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221110102307.3492557-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33a0a1e3b3 ]
kobject_get_path() does not modify the kobject passed to it, so make the
pointer constant.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20221001165315.2690141-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 3bb2a01caa ("kobject: Fix slab-out-of-bounds in fill_kobj_path()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df24ac7a2e ]
Currently nfsd4_setup_inter_ssc returns the vfsmount of the source
server's export when the mount completes. After the copy is done
nfsd4_cleanup_inter_ssc is called with the vfsmount of the source
server and it searches nfsd_ssc_mount_list for a matching entry
to do the clean up.
The problems with this approach are (1) the need to search the
nfsd_ssc_mount_list and (2) the code has to handle the case where
the matching entry is not found which looks ugly.
The enhancement is instead of nfsd4_setup_inter_ssc returning the
vfsmount, it returns the nfsd4_ssc_umount_item which has the
vfsmount embedded in it. When nfsd4_cleanup_inter_ssc is called
it's passed with the nfsd4_ssc_umount_item directly to do the
clean up so no searching is needed and there is no need to handle
the 'not found' case.
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
[ cel: adjusted whitespace and variable/function names ]
Reviewed-by: Olga Kornievskaia <kolga@netapp.com>
Stable-dep-of: 34e8f9ec4c ("NFSD: fix leaked reference count of nfsd4_ssc_umount_item")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdff966bfd ]
Add struct snd_pcm_substream forward declaration
Fixes: 078a85f280 ("ASoC: dapm: Only power up active channels from a DAI")
Signed-off-by: Lucas Tanure <lucas.tanure@collabora.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230215132851.1626881-1-lucas.tanure@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03a8610555 ]
In certain circumstances, such as when creating I2C-connected HID
devices, we want to pass and retain some quirks (axis inversion, etc).
The source of such quirks may be device tree, or DMI data, or something
else not readily available to the HID core itself and therefore cannot
be reconstructed easily. To allow this, introduce "initial_quirks" field
in hid_device structure and use it when determining the final set of
quirks.
This fixes the problem with i2c-hid setting up device-tree sourced
quirks too late and losing them on device rebind, and also allows to
sever the tie between hid-code and i2c-hid when applying DMI-based
quirks.
Fixes: b60d3c803d ("HID: i2c-hid-of: Expose the touchscreen-inverted properties")
Fixes: a2f416bf06 ("HID: multitouch: Add quirks for flipped axes")
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Tested-by: Allen Ballway <ballway@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/Y+LYwu3Zs13hdVDy@google.com
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d045bceff5 ]
Some motherboards have multiple HDA codecs connected to the serial bus.
The current code may create multiple mixer controls with the almost
identical identification.
The current code use id.device field from the control element structure
to store the codec address to avoid such clashes for multiple codecs.
Unfortunately, the user space do not handle this correctly. For mixer
controls, only name and index are used for the identifiers.
This patch fixes this problem to compose the index using the codec
address as an offset in case, when the control already exists. It is
really unlikely that one codec will create 10 similar controls.
This patch adds new kernel module parameter 'ctl_dev_id' to allow
select the old behaviour, too. The CONFIG_SND_HDA_CTL_DEV_ID Kconfig
option sets the default value.
BugLink: https://github.com/alsa-project/alsa-lib/issues/294
BugLink: https://github.com/alsa-project/alsa-lib/issues/205
Fixes: 54d1740315 ("[ALSA] hda-codec - Fix connection list parsing")
Fixes: 1afe206ab6 ("ALSA: hda - Try to find an empty control index when it's occupied")
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230202092013.4066998-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86bd0c4a2a ]
The Exynos UFS controller only supports scatter/gather list elements that
are aligned on a 4 KiB boundary. Fix DMA alignment in case PAGE_SIZE !=
4096. Rename UFSHCD_QUIRK_ALIGN_SG_WITH_PAGE_SIZE into
UFSHCD_QUIRK_4KB_DMA_ALIGNMENT.
Cc: Kiwoong Kim <kwmad.kim@samsung.com>
Fixes: 2b2bfc8aa5 ("scsi: ufs: Introduce a quirk to allow only page-aligned sg entries")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9d27c6be5 ]
The MIPI DCS specification demands that brightness values are sent in
big endian byte order. It also states that one parameter (i.e. one byte)
shall be sent/received for 8 bit wide values, and two parameters shall
be used for values that are between 9 and 16 bits wide.
Add new functions to properly handle 16-bit brightness in big endian,
since the two 8- and 16-bit cases are distinct from each other.
[richard: use separate functions instead of switch/case]
[richard: split into 16-bit component]
Fixes: 1a9d759331 ("drm/dsi: Implement DCS set/get display brightness")
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Link: https://android.googlesource.com/kernel/msm/+/754affd62d0ee268c686c53169b1dbb7deac8550
[richard: fix 16-bit brightness_get]
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Tested-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230116224909.23884-2-mailingradian@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8f185e39b ]
The call "skb_copy_from_linear_data(skb, inl + 1, spc)" triggers a FORTIFY
memcpy() warning on ppc64 platform:
In function ‘fortify_memcpy_chk’,
inlined from ‘skb_copy_from_linear_data’ at ./include/linux/skbuff.h:4029:2,
inlined from ‘build_inline_wqe’ at drivers/net/ethernet/mellanox/mlx4/en_tx.c:722:4,
inlined from ‘mlx4_en_xmit’ at drivers/net/ethernet/mellanox/mlx4/en_tx.c:1066:3:
./include/linux/fortify-string.h:513:25: error: call to ‘__write_overflow_field’ declared with
attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()?
[-Werror=attribute-warning]
513 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Same behaviour on x86 you can get if you use "__always_inline" instead of
"inline" for skb_copy_from_linear_data() in skbuff.h
The call here copies data into inlined tx destricptor, which has 104
bytes (MAX_INLINE) space for data payload. In this case "spc" is known
in compile-time but the destination is used with hidden knowledge
(real structure of destination is different from that the compiler
can see). That cause the fortify warning because compiler can check
bounds, but the real bounds are different. "spc" can't be bigger than
64 bytes (MLX4_INLINE_ALIGN), so the data can always fit into inlined
tx descriptor. The fact that "inl" points into inlined tx descriptor is
determined earlier in mlx4_en_xmit().
Avoid confusing the compiler with "inl + 1" constructions to get to past
the inl header by introducing a flexible array "data" to the struct so
that the compiler can see that we are not dealing with an array of inl
structs, but rather, arbitrary data following the structure. There are
no changes to the structure layout reported by pahole, and the resulting
machine code is actually smaller.
Reported-by: Josef Oskera <joskera@redhat.com>
Link: https://lore.kernel.org/lkml/20230217094541.2362873-1-joskera@redhat.com
Fixes: f68f2ff915 ("fortify: Detect struct member overflows in memcpy() at compile-time")
Cc: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20230218183842.never.954-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 997849c4b9 ]
Currently the freed element in bpf memory allocator may be immediately
reused, for htab map the reuse will reinitialize special fields in map
value (e.g., bpf_spin_lock), but lookup procedure may still access
these special fields, and it may lead to hard-lockup as shown below:
NMI backtrace for cpu 16
CPU: 16 PID: 2574 Comm: htab.bin Tainted: G L 6.1.0+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
RIP: 0010:queued_spin_lock_slowpath+0x283/0x2c0
......
Call Trace:
<TASK>
copy_map_value_locked+0xb7/0x170
bpf_map_copy_value+0x113/0x3c0
__sys_bpf+0x1c67/0x2780
__x64_sys_bpf+0x1c/0x20
do_syscall_64+0x30/0x60
entry_SYSCALL_64_after_hwframe+0x46/0xb0
......
</TASK>
For htab map, just like the preallocated case, these is no need to
initialize these special fields in map value again once these fields
have been initialized. For preallocated htab map, these fields are
initialized through __GFP_ZERO in bpf_map_area_alloc(), so do the
similar thing for non-preallocated htab in bpf memory allocator. And
there is no need to use __GFP_ZERO for per-cpu bpf memory allocator,
because __alloc_percpu_gfp() does it implicitly.
Fixes: 0fd7c5d433 ("bpf: Optimize call_rcu in non-preallocated hash map.")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20230215082132.3856544-2-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 584f374289 ]
Add sock_init_data_uid() to explicitly initialize the socket uid.
To initialise the socket uid, sock_init_data() assumes a the struct
socket* sock is always embedded in a struct socket_alloc, used to
access the corresponding inode uid. This may not be true.
Examples are sockets created in tun_chr_open() and tap_open().
Fixes: 86741ec254 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28319d6dc5 ]
RCU Tasks and PID-namespace unshare can interact in do_exit() in a
complicated circular dependency:
1) TASK A calls unshare(CLONE_NEWPID), this creates a new PID namespace
that every subsequent child of TASK A will belong to. But TASK A
doesn't itself belong to that new PID namespace.
2) TASK A forks() and creates TASK B. TASK A stays attached to its PID
namespace (let's say PID_NS1) and TASK B is the first task belonging
to the new PID namespace created by unshare() (let's call it PID_NS2).
3) Since TASK B is the first task attached to PID_NS2, it becomes the
PID_NS2 child reaper.
4) TASK A forks() again and creates TASK C which get attached to PID_NS2.
Note how TASK C has TASK A as a parent (belonging to PID_NS1) but has
TASK B (belonging to PID_NS2) as a pid_namespace child_reaper.
5) TASK B exits and since it is the child reaper for PID_NS2, it has to
kill all other tasks attached to PID_NS2, and wait for all of them to
die before getting reaped itself (zap_pid_ns_process()).
6) TASK A calls synchronize_rcu_tasks() which leads to
synchronize_srcu(&tasks_rcu_exit_srcu).
7) TASK B is waiting for TASK C to get reaped. But TASK B is under a
tasks_rcu_exit_srcu SRCU critical section (exit_notify() is between
exit_tasks_rcu_start() and exit_tasks_rcu_finish()), blocking TASK A.
8) TASK C exits and since TASK A is its parent, it waits for it to reap
TASK C, but it can't because TASK A waits for TASK B that waits for
TASK C.
Pid_namespace semantics can hardly be changed at this point. But the
coverage of tasks_rcu_exit_srcu can be reduced instead.
The current task is assumed not to be concurrently reapable at this
stage of exit_notify() and therefore tasks_rcu_exit_srcu can be
temporarily relaxed without breaking its constraints, providing a way
out of the deadlock scenario.
[ paulmck: Fix build failure by adding additional declaration. ]
Fixes: 3f95aa81d2 ("rcu: Make TASKS_RCU handle tasks that are almost done exiting")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Suggested-by: Boqun Feng <boqun.feng@gmail.com>
Suggested-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Eric W . Biederman <ebiederm@xmission.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
