commit 262d7a52ba upstream.
Under certain circumstances we send two EFLUSH commands, resulting in two
EFLUSH ack packets, while only expecting a single EFLUSH ack.
This can cause the driver Tx flush completion to get out of sync.
To avoid this problem, don't enable the "Transmit buffer flush done" (TFD)
interrupt and remove the code handling it.
Now we only send EFLUSH command after receiving status packet with
"Init detected" (IDET) bit set.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf7ac55e99 upstream.
The listen-only bit was never cleared, causing the controller to
always use listen-only mode, if previously set.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c589557dd1 upstream.
Empty the "Shared receive buffer" (SRB) in probe, to assure we start in a
known state, and don't process any irrelevant packets.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aed0e6ca7d upstream.
Set can.state to CAN_STATE_STOPPED in kvaser_pciefd_stop().
Without this fix, wrong CAN state was repported after the interface was
brought down.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c46e78ba9a ]
The XPCS expects clause 73 (copper backplane) autoneg to follow the
ethtool autoneg bit. It actually did that until the blamed
commit inaptly replaced state->an_enabled (coming from ethtool) with
phylink_autoneg_inband() (coming from the device tree or struct
phylink_config), as part of an unrelated phylink_pcs API conversion.
Russell King suggests that state->an_enabled from the original code was
just a proxy for the ethtool Autoneg bit, and that the correct way of
restoring the functionality is to check for this bit in the advertising
mask.
Fixes: 11059740e6 ("net: pcs: xpcs: convert to phylink_pcs_ops")
Link: https://lore.kernel.org/netdev/ZGNt2MFeRolKGFck@shell.armlinux.org.uk/
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60829145f1 ]
In suspend and resume cycle, the removal and rescan of device ends
up in NULL pointer dereference.
During driver initialization, if the ipc_imem_wwan_channel_init()
fails to get the valid device capabilities it returns an error and
further no resource (wwan struct) will be allocated. Now in this
situation if driver removal procedure is initiated it would result
in NULL pointer exception since unallocated wwan struct is dereferenced
inside ipc_wwan_deinit().
ipc_imem_run_state_worker() to handle the called functions return value
and to release the resource in failure case. It also reports the link
down event in failure cases. The user space application can handle this
event to do a device reset for restoring the device communication.
Fixes: 3670970dd8 ("net: iosm: shared memory IPC interface")
Reported-by: Samuel Wein PhD <sam@samwein.com>
Closes: https://lore.kernel.org/netdev/20230427140819.1310f4bd@kernel.org/T/
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60d758659f ]
In igb_hash_mc_addr() the expression:
"mc_addr[4] >> 8 - bit_shift", right shifting "mc_addr[4]"
shift by more than 7 bits always yields zero, so hash becomes not so different.
Add initialization with bit_shift = 1 and add a loop condition to ensure
bit_shift will be always in [1..8] range.
Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1323e0c6e1 ]
According to datasheet, the command opcode must be specified
into bits [14:12] of the Extended Port Control register (EPC).
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marco Migliore <m.migliore@tiesse.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 412cd77a2c ]
cas_saturn_firmware_init() allocates some memory using vmalloc(). This
memory is freed in the .remove() function but not it the error handling
path of the probe.
Add the missing vfree() to avoid a memory leak, should an error occur.
Fixes: fcaa40669c ("cassini: use request_firmware")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab00af85d2 ]
The error handling in tun_get_user is very scattered.
This patch unifies error handling, reduces duplication of code, and
makes the logic clearer.
Signed-off-by: Chuang Wang <nashuiliang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 82b2bc2794 ("tun: Fix memory leak for detached NAPI queue.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 682b6dc29d ]
If the firmware sends us a corrupted MCC response with
n_channels much larger than the command response can be,
we might copy far too much (uninitialized) memory and
even crash if the n_channels is large enough to make it
run out of the one page allocated for the FW response.
Fix that by checking the lengths. Doing a < comparison
would be sufficient, but the firmware should be doing
it correctly, so check more strictly.
Fixes: dcaf9f5ecb ("iwlwifi: mvm: add MCC update FW API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.d7b233139eb4.I51fd319df8e9d41881fc8450e83d78049518a79a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3ae69180b ]
The DBGI dump is (unsurprisingly) of type DBGI, not SRAM.
This leads to bad register accesses because the union is
built differently, there's no allocation ID, and thus the
allocation ID ends up being 0x8000.
Note that this was already wrong for DRAM vs. SMEM since
they use different parts of the union, but the allocation
ID is at the same place, so it worked.
Fix all of this but set the allocation ID in a way that
the offset calculation ends up without any offset.
Fixes: 34bc27783a ("iwlwifi: yoyo: fix DBGI_SRAM ini dump header.")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.19a302ae4c65.I12272599f7c1930666157b9d5e7f81fe9ec4c421@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2d8b7f257 ]
Lockdep points out that we can deadlock here by calling
cancel_delayed_work_sync() because that might be already
running and gotten interrupted by the NAPI soft-IRQ.
Even just calling something that can sleep is wrong in
this context though.
Luckily, it doesn't even really matter since the things
we need to do are idempotent, so just drop the _sync().
Fixes: e5d153ec54 ("iwlwifi: mvm: fix CSA AP side")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.b1813c823b4d.I9d20cc06d24fa40b6774d3dd95ea5e2bf8dd015b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7255355a06 ]
Fix the current implementation that causes ice_trigger_vf_reset()
to start resetting the VF even when the VF-NIC is still initializing.
When we reset NIC with ice driver it can interfere with
iavf-vf initialization e.g. during consecutive resets induced by ice
iavf ice
| |
|<-----------------|
| ice resets vf
iavf |
reset |
start |
|<-----------------|
| ice resets vf
| causing iavf
| initialization
| error
| |
iavf
reset
end
This leads to a series of -53 errors
(failed to init adminq) from the IAVF.
Change the state of the vf_state field to be not active when the IAVF
is still initializing. Make sure to wait until receiving the message on
the message box to ensure that the vf is ready and initializded.
In simple terms we use the ACTIVE flag to make sure that the ice
driver knows if the iavf is ready for another reset
iavf ice
| |
| |
|<------------- ice resets vf
iavf vf_state != ACTIVE
reset |
start |
| |
| |
iavf |
reset-------> vf_state == ACTIVE
end ice resets vf
| |
| |
Fixes: c54d209c78 ("ice: Wait for VF to be reset/ready before configuration")
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa4a15c85c ]
When hardware is reset, the VF relies on the VFGEN_RSTAT register to detect
when the VF is finished resetting. This is a tri-state register where 0
indicates a reset is in progress, 1 indicates the hardware is done
resetting, and 2 indicates that the software is done resetting.
Currently the PF driver relies on the device hardware resetting VFGEN_RSTAT
when a global reset occurs. This works ok, but it does mean that the VF
might not immediately notice a reset when the driver first detects that the
global reset is occurring.
This is also problematic for Scalable IOV, because there is no read/write
equivalent VFGEN_RSTAT register for the Scalable VSI type. Instead, the
Scalable IOV VFs will need to emulate this register.
To support this, introduce a new VF operation, clear_reset_state, which is
called when the PF driver first detects a global reset. The Single Root IOV
implementation can just write to VFGEN_RSTAT to ensure it's cleared
immediately, without waiting for the actual hardware reset to begin. The
Scalable IOV implementation will use this as part of its tracking of the
reset status to allow properly reporting the emulated VFGEN_RSTAT to the VF
driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 7255355a06 ("ice: Fix ice VF reset during iavf initialization")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 225c657945 ]
Removing the phy_stop() from bcmgenet_netif_stop() ended up causing
warnings from the PHY library that phy_start() is called from the
RUNNING state since we are no longer stopping the PHY state machine
during bcmgenet_suspend().
Restore the call to phy_stop() but make it conditional on being called
from the close or suspend path.
Fixes: c96e731c93 ("net: bcmgenet: connect and disconnect from the PHY state machine")
Fixes: 93e0401e0f ("net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230515025608.2587012-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93e0401e0f ]
The call to phy_stop() races with the later call to phy_disconnect(),
resulting in concurrent phy_suspend() calls being run from different
CPUs. The final call to phy_disconnect() ensures that the PHY is
stopped and suspended, too.
Fixes: c96e731c93 ("net: bcmgenet: connect and disconnect from the PHY state machine")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bffdc38f9 ]
can_put_echo_skb() checks for the enabled IFF_ECHO flag and the
correct ETH_P type of the given skbuff. When implementing the CAN XL
support the new check for ETH_P_CANXL has been forgotten.
Fixes: fb08cba12b ("can: canxl: update CAN infrastructure for CAN XL frames")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230506184515.39241-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5306623a98 ]
When initializing XDP in virtnet_open(), some rq xdp initialization
may hit an error causing net device open failed. However, previous
rqs have already initialized XDP and enabled NAPI, which is not the
expected behavior. Need to roll back the previous rq initialization
to avoid leaks in error unwinding of init code.
Also extract helper functions of disable and enable queue pairs.
Use newly introduced disable helper function in error unwinding and
virtnet_close. Use enable helper function in virtnet_open.
Fixes: 754b8a21a9 ("virtio_net: setup xdp_rxq_info")
Signed-off-by: Feng Liu <feliu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27369c9c2b ]
To easily audit the code, better to keep the device stop()
sequence to be mirror of the device open() sequence.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5306623a98 ("virtio_net: Fix error unwinding of XDP initialization")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b45d5ff8c ]
The timeout of the cmdq reset command has been increased to
resolve the reset timeout issue in the full VF scenario.
The timeout of other cmdq commands remains unchanged.
Fixes: 8d307f8e8c ("net: hns3: create new set of unified hclge_comm_cmd_send APIs")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 814d0c7860 ]
Currently the hns3 vf function reset delays 5000ms before vf rebuild
process. In product applications, this delay is too long for application
configurations and causes configuration timeout.
According to the tests, 500ms delay is enough for reset process except PF
FLR. So this patch modifies delay to 500ms in these scenarios.
Fixes: 6988eb2a9b ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f14db07064 ]
To prevent the system from abnormally sending PFC frames after an
abnormal reset. The hns3 driver notifies the firmware to disable pfc
before reset.
Fixes: 35d93a3004 ("net: hns3: adjust the process of PF reset")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89f6bfb071 ]
In function hns3_dump_tx_queue_info, The print buffer is not enough when
the tx BD number is configured to 32760. As a result several BD
information wouldn't be displayed.
So fix it by increasing the tx queue print buffer length.
Fixes: 630a6738da ("net: hns3: adjust string spaces of some parameters of tx bd info in debugfs")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec52b69c04 ]
When ports are in standalone mode, they should have learning disabled to
avoid adding new entries in the MAC lookup table which might be used by
other bridge ports to forward packets. While adding that, also make sure
learning is enabled for CPU port.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebe9bc5095 ]
stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e4b45f20c ]
Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 134120b066 ]
By default we would not want RXFCS and RXALL features enabled as they are
mainly intended for debugging purposes. This does not stop users from
enabling them later on as needed.
Fixes: 8e57daf706 ("sfc_ef100: RX path for EF100")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Co-developed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b01db2740 ]
Introduce the W/A for packet errors seen with short cables (<1m) between
two DP83867 PHYs.
The W/A recommended by DM requires FFE Equalizer Configuration tuning by
writing value 0x0E81 to DSP_FFE_CFG register (0x012C), surrounded by hard
and soft resets as follows:
write_reg(0x001F, 0x8000); //hard reset
write_reg(DSP_FFE_CFG, 0x0E81);
write_reg(0x001F, 0x4000); //soft reset
Since DP83867 PHY DM says "Changing this register to 0x0E81, will not
affect Long Cable performance.", enable the W/A by default.
Fixes: 2a10154abc ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f816b9829b ]
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230510200020.1534610-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9fff67d2d ]
While running traffics for a long time, randomly an RX descriptor
filled with value "0" from REO destination ring is received.
This descriptor which is invalid causes the wrong SKB (SKB stored in
the IDR lookup with buffer id "0") to be fetched which in turn
causes SKB memory corruption issue and the same leads to crash
after some time.
Changed the start id for idr allocation to "1" and the buffer id "0"
is reserved for error validation. Introduced Sanity check to validate
the descriptor, before processing the SKB.
Crash Signature :
Unable to handle kernel paging request at virtual address 3f004900
PC points to "b15_dma_inv_range+0x30/0x50"
LR points to "dma_cache_maint_page+0x8c/0x128".
The Backtrace obtained is as follows:
[<8031716c>] (b15_dma_inv_range) from [<80313a4c>] (dma_cache_maint_page+0x8c/0x128)
[<80313a4c>] (dma_cache_maint_page) from [<80313b90>] (__dma_page_dev_to_cpu+0x28/0xcc)
[<80313b90>] (__dma_page_dev_to_cpu) from [<7fb5dd68>] (ath11k_dp_process_rx+0x1e8/0x4a4 [ath11k])
[<7fb5dd68>] (ath11k_dp_process_rx [ath11k]) from [<7fb53c20>] (ath11k_dp_service_srng+0xb0/0x2ac [ath11k])
[<7fb53c20>] (ath11k_dp_service_srng [ath11k]) from [<7f67bba4>] (ath11k_pci_ext_grp_napi_poll+0x1c/0x78 [ath11k_pci])
[<7f67bba4>] (ath11k_pci_ext_grp_napi_poll [ath11k_pci]) from [<807d5cf4>] (__napi_poll+0x28/0xb8)
[<807d5cf4>] (__napi_poll) from [<807d5f28>] (net_rx_action+0xf0/0x280)
[<807d5f28>] (net_rx_action) from [<80302148>] (__do_softirq+0xd0/0x280)
[<80302148>] (__do_softirq) from [<80320408>] (irq_exit+0x74/0xd4)
[<80320408>] (irq_exit) from [<803638a4>] (__handle_domain_irq+0x90/0xb4)
[<803638a4>] (__handle_domain_irq) from [<805bedec>] (gic_handle_irq+0x58/0x90)
[<805bedec>] (gic_handle_irq) from [<80301a78>] (__irq_svc+0x58/0x8c)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403191533.28114-1-quic_nmaran@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef16799640 ]
A received TKIP key may be up to 32 bytes because it may contain
MIC rx/tx keys too. These are not used by iwl and copying these
over overflows the iwl_keyinfo.key field.
Add a check to not copy more data to iwl_keyinfo.key then will fit.
This fixes backtraces like this one:
memcpy: detected field-spanning write (size 32) of single field "sta_cmd.key.key" at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 (size 16)
WARNING: CPU: 1 PID: 946 at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Hardware name: Dell Inc. Latitude E6430/0H3MT5, BIOS A21 05/08/2017
RIP: 0010:iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Call Trace:
<TASK>
iwl_set_dynamic_key+0x1f0/0x220 [iwldvm]
iwlagn_mac_set_key+0x1e4/0x280 [iwldvm]
drv_set_key+0xa4/0x1b0 [mac80211]
ieee80211_key_enable_hw_accel+0xa8/0x2d0 [mac80211]
ieee80211_key_replace+0x22d/0x8e0 [mac80211]
<snip>
Link: https://www.alionet.org/index.php?topic=1469.0
Link: https://lore.kernel.org/linux-wireless/20230218191056.never.374-kees@kernel.org/
Link: https://lore.kernel.org/linux-wireless/68760035-7f75-1b23-e355-bfb758a87d83@redhat.com/
Cc: Kees Cook <keescook@chromium.org>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2bc600cce ]
For MLO, we cannot use vif->bss_conf.chandef.chan->band, since
that will lead to a NULL-ptr dereference as bss_conf isn't used.
However, in case of real MLO, we also need to take both LMACs
into account if they exist, since the station might be active
on both LMACs at the same time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.3588afc85d79.I11592893bbc191b9548518b8bd782de568a9f848@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a06bfb3c9f ]
When max virtual ap interfaces are configured in all the bands with
ACS and hostapd restart is done every 60s, a crash is observed at
random times.
In this certain scenario, a fragmented packet is received for
self peer, for which rx_tid and rx_frags are not initialized in
datapath. While handling this fragment, crash is observed as the
rx_frag list is uninitialised and when we walk in
ath11k_dp_rx_h_sort_frags, skb null leads to exception.
To address this, before processing received fragments we check
dp_setup_done flag is set to ensure that peer has completed its
dp peer setup for fragment queue, else ignore processing the
fragments.
Call trace:
ath11k_dp_process_rx_err+0x550/0x1084 [ath11k]
ath11k_dp_service_srng+0x70/0x370 [ath11k]
0xffffffc009693a04
__napi_poll+0x30/0xa4
net_rx_action+0x118/0x270
__do_softirq+0x10c/0x244
irq_exit+0x64/0xb4
__handle_domain_irq+0x88/0xac
gic_handle_irq+0x74/0xbc
el1_irq+0xf0/0x1c0
arch_cpu_idle+0x10/0x18
do_idle+0x104/0x248
cpu_startup_entry+0x20/0x64
rest_init+0xd0/0xdc
arch_call_rest_init+0xc/0x14
start_kernel+0x480/0x4b8
Code: f9400281 f94066a2 91405021 b94a0023 (f9406401)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403184155.8670-2-quic_nmaran@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d066a530af ]
If adding a key to firmware fails we leak the allocated ptk_pn.
This shouldn't happen in practice, but we should still fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.99446ffd02bc.I82a2ad6ec1395f188e0a1677cc619e3fcb1feac9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58d1b71787 ]
An integer overflow occurs in the iwl_write_to_user_buf() function,
which is called by the iwl_dbgfs_monitor_data_read() function.
static bool iwl_write_to_user_buf(char __user *user_buf, ssize_t count,
void *buf, ssize_t *size,
ssize_t *bytes_copied)
{
int buf_size_left = count - *bytes_copied;
buf_size_left = buf_size_left - (buf_size_left % sizeof(u32));
if (*size > buf_size_left)
*size = buf_size_left;
If the user passes a SIZE_MAX value to the "ssize_t count" parameter,
the ssize_t count parameter is assigned to "int buf_size_left".
Then compare "*size" with "buf_size_left" . Here, "buf_size_left" is a
negative number, so "*size" is assigned "buf_size_left" and goes into
the third argument of the copy_to_user function, causing a heap overflow.
This is not a security vulnerability because iwl_dbgfs_monitor_data_read()
is a debugfs operation with 0400 privileges.
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.2d80ace81532.Iecfba549e0e0be21bbb0324675392e42e75bd5ad@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b655b9a9f8 ]
It is possible that iwl_pci_probe() will fail and free the trans,
then afterwards iwl_pci_remove() will be called and crash by trying
to access trans which is already freed, fix it.
iwlwifi 0000:01:00.0: Detected crf-id 0xa5a5a5a2, cnv-id 0xa5a5a5a2
wfpm id 0xa5a5a5a2
iwlwifi 0000:01:00.0: Can't find a correct rfid for crf id 0x5a2
...
BUG: kernel NULL pointer dereference, address: 0000000000000028
...
RIP: 0010:iwl_pci_remove+0x12/0x30 [iwlwifi]
pci_device_remove+0x3e/0xb0
device_release_driver_internal+0x103/0x1f0
driver_detach+0x4c/0x90
bus_remove_driver+0x5c/0xd0
driver_unregister+0x31/0x50
pci_unregister_driver+0x40/0x90
iwl_pci_unregister_driver+0x15/0x20 [iwlwifi]
__exit_compat+0x9/0x98 [iwlwifi]
__x64_sys_delete_module+0x147/0x260
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.082f6e21341b.I0db21d7fa9a828d571ca886713bd0b5d0b6e1e5c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8384d4a51 ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
warning in clang aims to catch these at compile time, which reveals:
drivers/net/ethernet/pasemi/pasemi_mac.c:1665:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = pasemi_mac_start_tx,
^~~~~~~~~~~~~~~~~~~
1 error generated.
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of
pasemi_mac_start_tx() to match the prototype's to resolve the warning.
While PowerPC does not currently implement support for kCFI, it could in
the future, which means this warning becomes a fatal CFI failure at run
time.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230319-pasemi-incompatible-pointer-types-strict-v1-1-1b9459d8aef0@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c6dddc239 ]
The value of an arithmetic expression is subject
of possible overflow due to a failure to cast operands to a larger data
type before performing arithmetic. Used macro for multiplication instead
operator for avoiding overflow.
Found by Security Code and Linux Verification
Center (linuxtesting.org) with SVACE.
Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230309174347.3515-1-korotkov.maxim.s@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89b89e5215 ]
Apparently the hex passphrase mechanism does not work on newer
chips/firmware (e.g. BCM4387). It seems there was a simple way of
passing it in binary all along, so use that and avoid the hexification.
OpenBSD has been doing it like this from the beginning, so this should
work on all chips.
Also clear the structure before setting the PMK. This was leaking
uninitialized stack contents to the device.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230214092423.15175-6-marcan@marcan.st
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91918ce88d ]
Newer Apple firmwares on chipsets without a hardware RNG require the
host to provide a buffer of 256 random bytes to the device on
initialization. This buffer is present immediately before NVRAM,
suffixed by a footer containing a magic number and the buffer length.
This won't affect chips/firmwares that do not use this feature, so do it
unconditionally for all Apple platforms (those with an Apple OTP).
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230214080034.3828-3-marcan@marcan.st
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfcc8ba45e ]
The memcpy() in ath_key_config() was attempting to write across
neighboring struct members in struct ath_keyval. Introduce a wrapping
struct_group, kv_values, to be the addressable target of the memcpy
without overflowing an individual member. Silences the false positive
run-time warning:
memcpy: detected field-spanning write (size 32) of single field "hk.kv_val" at drivers/net/wireless/ath/key.c:506 (size 16)
Link: https://bbs.archlinux.org/viewtopic.php?id=282254
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230210054310.never.554-kees@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
