[ Upstream commit ab87603b25 ]
When the system attempts to sleep while mtk_t7xx is not ready, the driver
cannot put the device to sleep:
[ 12.472918] mtk_t7xx 0000:57:00.0: [PM] Exiting suspend, modem in invalid state
[ 12.472936] mtk_t7xx 0000:57:00.0: PM: pci_pm_suspend(): t7xx_pci_pm_suspend+0x0/0x20 [mtk_t7xx] returns -14
[ 12.473678] mtk_t7xx 0000:57:00.0: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x1b0 returns -14
[ 12.473711] mtk_t7xx 0000:57:00.0: PM: failed to suspend async: error -14
[ 12.764776] PM: Some devices failed to suspend, or early wake event detected
Mediatek confirmed the device can take a rather long time to complete
its initialization, so wait for up to 20 seconds until init is done.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 212457ccbd ]
clang warns about an unpacked structure inside of a packed one:
drivers/net/wireless/broadcom/b43/b43.h:654:4: error: field data within 'struct b43_iv' is less aligned than 'union (unnamed union at /home/arnd/arm-soc/drivers/net/wireless/broadcom/b43/b43.h:651:2)' and is usually due to 'struct b43_iv' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
The problem here is that the anonymous union has the default alignment
from its members, apparently because the original author mixed up the
placement of the __packed attribute by placing it next to the struct
member rather than the union definition. As the struct itself is
also marked as __packed, there is no need to mark its members, so just
move the annotation to the inner type instead.
As Michael noted, the same problem is present in b43legacy, so
change both at the same time.
Acked-by: Michael Büsch <m@bues.ch>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/oe-kbuild-all/202305160749.ay1HAoyP-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516183442.536589-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8938bc881 ]
The rs_drv_get_rate flow reads the lq_sta to return the optimal rate
for tx frames. This read flow is not protected thereby leaving
a small window, a few instructions wide, open to contention by an
asynchronous rate update. Indeed this race condition was hit and the
update occurred in the middle of the read.
Fix this by locking the lq_sta struct during read.
Signed-off-by: Ariel Malamud <ariel.malamud@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.b52c9ed5c379.I15290b78e0d966c1b68278263776ca9de841d5fe@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20429444e6 ]
When using rtl8192cu with rtl8xxxu driver to connect wifi, there is a
probability of failure, which shows "authentication with ... timed out".
Through debugging, it was found that the RCR register has been inexplicably
modified to an incorrect value, resulting in the nic not being able to
receive authenticated frames.
To fix this problem, add regrcr in rtl8xxxu_priv struct, and store
the RCR value every time the register is written, and use it the next
time the register need to be modified.
Signed-off-by: Yun Lu <luyun@kylinos.cn>
Link: https://lore.kernel.org/all/20230427020512.1221062-1-luyun_611@163.com
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512012055.2990472-1-luyun_611@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c27f3d53d ]
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de4 ("net: dsa: mv88e6xxx: wait after reset deactivation")
Signed-off-by: Andreas Svensson <andreas.svensson@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbfa4b5899 ]
During driver load it reads embedded_cpu bit from initialization
segment, but the initialization segment is readable only after
initialization bit is cleared.
Move the call to mlx5_read_embedded_cpu() right after initialization bit
cleared.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Fixes: 591905ba96 ("net/mlx5: Introduce Mellanox SmartNIC and modify page management logic")
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6193d7030 ]
Allocation failure is outside the critical lock section and should
return immediately rather than jumping to the unlock section.
Also unlock as soon as required and remove the now redundant jump label.
Fixes: 80a2a9026b ("net/mlx5e: Add a lock on tir list")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc362e20cd ]
In the event of a change in XGBE mode, the current auto-negotiation
needs to be reset and the AN cycle needs to be re-triggerred. However,
the current code ignores the return value of xgbe_set_mode(), leading to
false information as the link is declared without checking the status
register.
Fix this by propagating the mode switch status information to
xgbe_phy_status().
Fixes: e57f7a3fea ("amd-xgbe: Prepare for working with more than one type of phy")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d68cb7cf1f ]
Do skb_put() after a new skb has been successfully allocated otherwise
the reused skb leads to skb_panics or incorrect packet sizes.
Fixes: f92e1869d7 ("Add Mellanox BlueField Gigabit Ethernet driver")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230524194908.147145-1-tbogendoerfer@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdf274750f ]
As part of switchdev mode disablement, driver changes port netdevice
profile from uplink to nic. If this process is triggered by health
recovery flow (PCI reset, for ex.) profile attach would fail because all
fw commands aborted when internal error flag is set. As a result, nic
netdevice profile is not attached and driver fails to rollback to uplink
profile, which leave driver in broken state and cause crash later.
To handle broken state do netdevice profile initialization only instead
of full attachment and release mdev resources on driver suspend as
expected. Actual netdevice attachment is done during driver load.
Fixes: c4d7eb5768 ("net/mxl5e: Add change profile method")
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 341a80de24 ]
mlx5 driver needs to parse traces with event_id inside the range of
first_string_trace and num_string_trace. However, mlx5 is parsing all
events with event_id >= first_string_trace.
Fix it by checking for the correct range.
Fixes: c71ad41ccb ("net/mlx5: FW tracer, events handling")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4646da057 ]
There is no point in recovery during device removal. Also, if health
work started need to wait for it to avoid races and NULL pointer
access.
Hence, drain health WQ before removing device.
Fixes: 1958fc2f07 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 824c8dc4a4 ]
mlx5 health mechanism is using devlink APIs, which are using devlink
notify APIs. After the cited patch, using devlink notify APIs after
devlink is unregistered triggers a WARN_ON().
Hence, drain health WQ before devlink is unregistered.
Fixes: cf53021740 ("devlink: Notify users when objects are accessible")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit a71f388045.
Commit a71f388045 ("thermal/drivers/mellanox: Use generic
thermal_zone_get_trip() function") was backported as a dependency of the
fix in upstream commit 6d206b1ea9 ("mlxsw: core_thermal: Fix fan speed
in maximum cooling state"). However, it is dependent on changes in the
thermal core that were merged in v6.3. Without them, the mlxsw driver is
unable to register its thermal zone:
mlxsw_spectrum 0000:03:00.0: Failed to register thermal zone
mlxsw_spectrum 0000:03:00.0: cannot register bus device
mlxsw_spectrum: probe of 0000:03:00.0 failed with error -22
Fix this by reverting this commit and instead fix the small conflict
with the above mentioned fix. Tested using the test case mentioned in
the change log of the fix:
# cat /sys/class/thermal/thermal_zone2/cdev0/type
mlxsw_fan
# echo 10 > /sys/class/thermal/thermal_zone2/cdev0/cur_state
# cat /sys/class/hwmon/hwmon1/name
mlxsw
# cat /sys/class/hwmon/hwmon1/pwm1
255
After setting the fan to its maximum cooling state (10), it operates at
100% duty cycle instead of being stuck at 0 RPM.
Fixes: a71f388045 ("thermal/drivers/mellanox: Use generic thermal_zone_get_trip() function")
Reported-by: Joe Botha <joe@atomic.ac>
Tested-by: Joe Botha <joe@atomic.ac>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb5edce271 ]
Upon physical link change, firmware reports to the kernel about the
change along with the details like speed, lmac_type_id, etc.
Kernel derives lmac_type based on lmac_type_id received from firmware.
In a few scenarios, firmware returns an invalid lmac_type_id, which
is resulting in below kernel panic. This patch adds the missing
validation of the lmac_type_id field.
Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 35.321595] Modules linked in:
[ 35.328982] CPU: 0 PID: 31 Comm: kworker/0:1 Not tainted
5.4.210-g2e3169d8e1bc-dirty #17
[ 35.337014] Hardware name: Marvell CN103XX board (DT)
[ 35.344297] Workqueue: events work_for_cpu_fn
[ 35.352730] pstate: 40400089 (nZcv daIf +PAN -UAO)
[ 35.360267] pc : strncpy+0x10/0x30
[ 35.366595] lr : cgx_link_change_handler+0x90/0x180
Fixes: 61071a871e ("octeontx2-af: Forward CGX link notifications to PFs")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 457d7fb03e ]
If we do get multiple notifications from firmware, then
we might have allocated 'notif', but don't free it. Fix
that by checking for duplicates before allocation.
Fixes: 4da46a06d4 ("wifi: iwlwifi: mvm: Add support for wowlan info notification")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.116758321cc4.I8bdbcbb38c89ac637eaa20dda58fa9165b25893a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 905d50ddbc ]
As part of version 2 we don't need to have wake_packet_bufsize
and wake_packet_length. The first one is already calculated by the driver,
the latter is sent as part of the wake packet notification.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.3b53213b10d4.Ibf2f15aca614def2d262dd267d1aad65931b58f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: 457d7fb03e ("wifi: iwlwifi: mvm: fix potential memory leak")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d33fc8d036 ]
Use primary channel index to determine which 5 MHz mask should be enable.
This mask is used to prevent noise from channel edge to effect CCA
threshold in wide bandwidth (>= 40 MHZ).
Fixes: 1b00e9236a ("rtw89: 8852c: add set channel of BB part")
Fixes: 6b0698984e ("wifi: rtw89: 8852b: add chip_ops::set_channel")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230406072841.8308-1-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71460c9ec5 ]
By default the VSC8501 and VSC8502 RGMII/GMII/MII RX_CLK output is
disabled. To allow packet forwarding towards the MAC it needs to be
enabled.
For other PHYs supported by this driver the clock output is enabled
by default.
Fixes: d316986331 ("net: phy: mscc: add support for VSC8502")
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c253dfc89 ]
devcom events are sent to all registered component. Following the
cited patch, it is possible for two components, e.g.: two eswitches,
to send devcom events, while both components are registered. This
means eswitch layer will do double un/pairing, which is double
allocation and free of resources, even though only one un/pairing is
needed. flow example:
cpu0 cpu1
---- ----
mlx5_devlink_eswitch_mode_set(dev0)
esw_offloads_devcom_init()
mlx5_devcom_register_component(esw0)
mlx5_devlink_eswitch_mode_set(dev1)
esw_offloads_devcom_init()
mlx5_devcom_register_component(esw1)
mlx5_devcom_send_event()
mlx5_devcom_send_event()
Hence, check whether the eswitches are already un/paired before
free/allocation of resources.
Fixes: 09b278462f ("net: devlink: enable parallel ops on netlink interface")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 57fb54ab9f upstream.
The mscc driver implements support for VSC8502, so its ID should be in
the MODULE_DEVICE_TABLE for automatic loading.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Fixes: d316986331 ("net: phy: mscc: add support for VSC8502")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 640bf95b2c upstream.
Should tc589_config() fail, some resources need to be released as already
done in the remove function.
Fixes: 15b99ac172 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/d8593ae867b24c79063646e36f9b18b0790107cb.1684575975.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f893f57a3 upstream.
From one hand, mlx5 driver is allowing to probe PFs in parallel.
From the other hand, devcom, which is a share resource between PFs, is
registered without any lock. This might resulted in memory problems.
Hence, use the global mlx5_dev_list_lock in order to serialize devcom
registration.
Fixes: fadd59fc50 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af87194352 upstream.
In case devcom allocation is failed, mlx5 is always freeing the priv.
However, this priv might have been allocated by a different thread,
and freeing it might lead to use-after-free bugs.
Fix it by freeing the priv only in case it was allocated by the
running thread.
Fixes: fadd59fc50 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a0a935fb6 upstream.
DEVX can issue a general command, which is not used by mlx5 driver.
In case such command is failed, mlx5 is trying to collect the failure
data, However, mlx5 doesn't create a storage for this command, since
mlx5 doesn't use it. This lead to array-index-out-of-bounds error.
Fix it by checking whether the command is known before collecting the
failure data.
Fixes: 34f46ae0d4 ("net/mlx5: Add command failures data to debugfs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7dd225bc2 upstream.
SW Steering uses RC QP for writing STEs to ICM. This writingis done in LB
(loopback), and FL (force-loopback) QP is preferred for performance. FL is
available when RoCE is enabled or disabled based on RoCE caps.
This patch adds reading of FL capability from HCA caps in addition to the
existing reading from RoCE caps, thus fixing the case where we didn't
have loopback enabled when RoCE was disabled.
Fixes: 7304d603a5 ("net/mlx5: DR, Add support for force-loopback QP")
Signed-off-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2be5bd42a5 upstream.
In case user switch a device from switchdev mode to legacy mode, mlx5
first unpair the E-switch and afterwards unload the uplink vport.
From the other hand, in case user remove or reload a device, mlx5
first unload the uplink vport and afterwards unpair the E-switch.
The latter is causing a bug[1], hence, handle pairing of E-switch as
part of uplink un/load APIs.
[1]
In case VF_LAG is used, every tc fdb flow is duplicated to the peer
esw. However, the original esw keeps a pointer to this duplicated
flow, not the peer esw.
e.g.: if user create tc fdb flow over esw0, the flow is duplicated
over esw1, in FW/HW, but in SW, esw0 keeps a pointer to the duplicated
flow.
During module unload while a peer tc fdb flow is still offloaded, in
case the first device to be removed is the peer device (esw1 in the
example above), the peer net-dev is destroyed, and so the mlx5e_priv
is memset to 0.
Afterwards, the peer device is trying to unpair himself from the
original device (esw0 in the example above). Unpair API invoke the
original device to clear peer flow from its eswitch (esw0), but the
peer flow, which is stored over the original eswitch (esw0), is
trying to use the peer mlx5e_priv, which is memset to 0 and result in
bellow kernel-oops.
[ 157.964081 ] BUG: unable to handle page fault for address: 000000000002ce60
[ 157.964662 ] #PF: supervisor read access in kernel mode
[ 157.965123 ] #PF: error_code(0x0000) - not-present page
[ 157.965582 ] PGD 0 P4D 0
[ 157.965866 ] Oops: 0000 [#1] SMP
[ 157.967670 ] RIP: 0010:mlx5e_tc_del_fdb_flow+0x48/0x460 [mlx5_core]
[ 157.976164 ] Call Trace:
[ 157.976437 ] <TASK>
[ 157.976690 ] __mlx5e_tc_del_fdb_peer_flow+0xe6/0x100 [mlx5_core]
[ 157.977230 ] mlx5e_tc_clean_fdb_peer_flows+0x67/0x90 [mlx5_core]
[ 157.977767 ] mlx5_esw_offloads_unpair+0x2d/0x1e0 [mlx5_core]
[ 157.984653 ] mlx5_esw_offloads_devcom_event+0xbf/0x130 [mlx5_core]
[ 157.985212 ] mlx5_devcom_send_event+0xa3/0xb0 [mlx5_core]
[ 157.985714 ] esw_offloads_disable+0x5a/0x110 [mlx5_core]
[ 157.986209 ] mlx5_eswitch_disable_locked+0x152/0x170 [mlx5_core]
[ 157.986757 ] mlx5_eswitch_disable+0x51/0x80 [mlx5_core]
[ 157.987248 ] mlx5_unload+0x2a/0xb0 [mlx5_core]
[ 157.987678 ] mlx5_uninit_one+0x5f/0xd0 [mlx5_core]
[ 157.988127 ] remove_one+0x64/0xe0 [mlx5_core]
[ 157.988549 ] pci_device_remove+0x31/0xa0
[ 157.988933 ] device_release_driver_internal+0x18f/0x1f0
[ 157.989402 ] driver_detach+0x3f/0x80
[ 157.989754 ] bus_remove_driver+0x70/0xf0
[ 157.990129 ] pci_unregister_driver+0x34/0x90
[ 157.990537 ] mlx5_cleanup+0xc/0x1c [mlx5_core]
[ 157.990972 ] __x64_sys_delete_module+0x15a/0x250
[ 157.991398 ] ? exit_to_user_mode_prepare+0xea/0x110
[ 157.991840 ] do_syscall_64+0x3d/0x90
[ 157.992198 ] entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: 04de7dda73 ("net/mlx5e: Infrastructure for duplicated offloading of TC flows")
Fixes: 1418ddd96a ("net/mlx5e: Duplicate offloaded TC eswitch rules under uplink LAG")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e5daf5565 upstream.
When calculating crc for hash index we use the function crc32 that
calculates for little-endian (LE) arch.
Then we convert it to network endianness using htonl(), but it's wrong
to do the conversion in BE archs since the crc32 value is already LE.
The solution is to switch the bytes from the crc result for all types
of arc.
Fixes: 40416d8ede ("net/mlx5: DR, Replace CRC32 implementation to use kernel lib")
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afbed3f748 upstream.
NAPI gets called with budget of 0 from netpoll, which has interrupts
disabled. We should try to free some space on Tx rings and nothing
else.
Specifically do not try to handle XDP TX or try to refill Rx buffers -
we can't use the page pool from IRQ context. Don't check if IRQs moved,
either, that makes no sense in netpoll. Netpoll calls _all_ the rings
from whatever CPU it happens to be invoked on.
In general do as little as possible, the work quickly adds up when
there's tens of rings to poll.
The immediate stack trace I was seeing is:
__do_softirq+0xd1/0x2c0
__local_bh_enable_ip+0xc7/0x120
</IRQ>
<TASK>
page_pool_put_defragged_page+0x267/0x320
mlx5e_free_xdpsq_desc+0x99/0xd0
mlx5e_poll_xdpsq_cq+0x138/0x3b0
mlx5e_napi_poll+0xc3/0x8b0
netpoll_poll_dev+0xce/0x150
AFAIU page pool takes a BH lock, releases it and since BH is now
enabled tries to run softirqs.
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Fixes: 60bbf7eeef ("mlx5: use page_pool for xdp_return_frame call")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be071cdb16 upstream.
With introduction of post action infrastructure most of the users of encap
attribute had been modified in order to obtain the correct attribute by
calling mlx5e_tc_get_encap_attr() helper instead of assuming encap action
is always on default attribute. However, the cited commit didn't modify
mlx5e_invalidate_encap() which prevents it from destroying correct modify
header action which leads to a warning [0]. Fix the issue by using correct
attribute.
[0]:
Feb 21 09:47:35 c-237-177-40-045 kernel: WARNING: CPU: 17 PID: 654 at drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:684 mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: RIP: 0010:mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: Call Trace:
Feb 21 09:47:35 c-237-177-40-045 kernel: <TASK>
Feb 21 09:47:35 c-237-177-40-045 kernel: mlx5e_tc_fib_event_work+0x8e3/0x1f60 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? mlx5e_take_all_encap_flows+0xe0/0xe0 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lock_downgrade+0x6d0/0x6d0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: process_one_work+0x7c2/0x1310
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x3f0/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? pwq_dec_nr_in_flight+0x230/0x230
Feb 21 09:47:35 c-237-177-40-045 kernel: ? rwlock_bug.part.0+0x90/0x90
Feb 21 09:47:35 c-237-177-40-045 kernel: worker_thread+0x59d/0xec0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? __kthread_parkme+0xd9/0x1d0
Fixes: 8300f22526 ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7aa5038019 upstream.
Check in the mlx5e_ptp_poll_ts_cq context if the ptp tx sq should be woken
up. Before change, the ptp tx sq may never wake up if the ptp tx ts skb
fifo is full when mlx5e_poll_tx_cq checks if the queue should be woken up.
Fixes: 1880bc4e4a ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b17a4971d upstream.
If an error occures after calling nv_mgmt_acquire_sema(), it should be
undone with a corresponding nv_mgmt_release_sema() call.
Add it in the error handling path of the probe as already done in the
remove function.
Fixes: cac1c52c36 ("forcedeth: mgmt unit interface")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Link: https://lore.kernel.org/r/355e9a7d351b32ad897251b6f81b5886fcdc6766.1684571393.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6007612459 upstream.
It was noticing that after a while when unloading/loading the driver and
sending traffic through the switch, it would stop working. It would stop
forwarding any traffic and the only way to get out of this was to do a
power cycle of the board. The root cause seems to be that the switch
core is initialized twice. Apparently initializing twice the switch core
disturbs the pointers in the queue systems in the HW, so after a while
it would stop sending the traffic.
Unfortunetly, it is not possible to use a reset of the switch here,
because the reset line is connected to multiple devices like MDIO,
SGPIO, FAN, etc. So then all the devices will get reseted when the
network driver will be loaded.
So the fix is to check if the core is initialized already and if that is
the case don't initialize it again.
Fixes: db8bcaad53 ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230522120038.3749026-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae9b15fbe6 upstream.
When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.
team0
|
+------+------+-----+-----+
| | | | |
team1 team2 team3 ... team200
If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.
But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.
Reproducer:
ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
ip link add team$i master team0 type team
ethtool -K team$i lro on
done
ethtool -K team0 lro off
In order to fix it, the notifier_ctx member of bonding/team is introduced.
Reported-by: syzbot+60748c96cf5c6df8e581@syzkaller.appspotmail.com
Fixes: fd867d51f8 ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230517143010.3596250-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e01c7f704 upstream.
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
Workqueue: mld mld_ifc_work
RIP: 0010:skb_panic net/core/skbuff.c:113 [inline]
RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118
[snip]
Call Trace:
<TASK>
skb_put+0x151/0x210 net/core/skbuff.c:2047
skb_put_zero include/linux/skbuff.h:2422 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline]
cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308
cdc_ncm_tx_fixup+0xa3/0x100
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Cc: stable@vger.kernel.org
Reported-by: syzbot+9f575a1f15fc0c01ed69@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=b982f1059506db48409d
Link: https://lore.kernel.org/all/20211202143437.1411410-1-lee.jones@linaro.org/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230517133808.1873695-2-tudor.ambarus@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91e87045a5 upstream.
Currently, the .port_set_rgmii_delay hook is missing for the 88E6320
family, which causes failure to retrieve an IP address via DHCP.
Add mv88e6320_port_set_rgmii_delay() that allows applying the RGMII
delay for ports 2, 5, and 6, which are the only ports that can be used
in RGMII mode.
Tested on a custom i.MX8MN board connected to an 88E6320 switch.
This change also applies safely to the 88E6321 variant.
The only difference between 88E6320 versus 88E6321 is the temperature
grade and pinout.
They share exactly the same MDIO register map for ports 2, 5, and 6,
which are the only ports that can be used in RGMII mode.
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
[fabio: Improved commit log and extended it to mv88e6321_ops]
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221028163158.198108-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 262d7a52ba upstream.
Under certain circumstances we send two EFLUSH commands, resulting in two
EFLUSH ack packets, while only expecting a single EFLUSH ack.
This can cause the driver Tx flush completion to get out of sync.
To avoid this problem, don't enable the "Transmit buffer flush done" (TFD)
interrupt and remove the code handling it.
Now we only send EFLUSH command after receiving status packet with
"Init detected" (IDET) bit set.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf7ac55e99 upstream.
The listen-only bit was never cleared, causing the controller to
always use listen-only mode, if previously set.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c589557dd1 upstream.
Empty the "Shared receive buffer" (SRB) in probe, to assure we start in a
known state, and don't process any irrelevant packets.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aed0e6ca7d upstream.
Set can.state to CAN_STATE_STOPPED in kvaser_pciefd_stop().
Without this fix, wrong CAN state was repported after the interface was
brought down.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c46e78ba9a ]
The XPCS expects clause 73 (copper backplane) autoneg to follow the
ethtool autoneg bit. It actually did that until the blamed
commit inaptly replaced state->an_enabled (coming from ethtool) with
phylink_autoneg_inband() (coming from the device tree or struct
phylink_config), as part of an unrelated phylink_pcs API conversion.
Russell King suggests that state->an_enabled from the original code was
just a proxy for the ethtool Autoneg bit, and that the correct way of
restoring the functionality is to check for this bit in the advertising
mask.
Fixes: 11059740e6 ("net: pcs: xpcs: convert to phylink_pcs_ops")
Link: https://lore.kernel.org/netdev/ZGNt2MFeRolKGFck@shell.armlinux.org.uk/
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60829145f1 ]
In suspend and resume cycle, the removal and rescan of device ends
up in NULL pointer dereference.
During driver initialization, if the ipc_imem_wwan_channel_init()
fails to get the valid device capabilities it returns an error and
further no resource (wwan struct) will be allocated. Now in this
situation if driver removal procedure is initiated it would result
in NULL pointer exception since unallocated wwan struct is dereferenced
inside ipc_wwan_deinit().
ipc_imem_run_state_worker() to handle the called functions return value
and to release the resource in failure case. It also reports the link
down event in failure cases. The user space application can handle this
event to do a device reset for restoring the device communication.
Fixes: 3670970dd8 ("net: iosm: shared memory IPC interface")
Reported-by: Samuel Wein PhD <sam@samwein.com>
Closes: https://lore.kernel.org/netdev/20230427140819.1310f4bd@kernel.org/T/
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60d758659f ]
In igb_hash_mc_addr() the expression:
"mc_addr[4] >> 8 - bit_shift", right shifting "mc_addr[4]"
shift by more than 7 bits always yields zero, so hash becomes not so different.
Add initialization with bit_shift = 1 and add a loop condition to ensure
bit_shift will be always in [1..8] range.
Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
