commit 44d0fb387b upstream.
The current uses of PageAnon in page table check functions can lead to
type confusion bugs between struct page and slab [1], if slab pages are
accidentally mapped into the user space. This is because slab reuses the
bits in struct page to store its internal states, which renders PageAnon
ineffective on slab pages.
Since slab pages are not expected to be mapped into the user space, this
patch adds BUG_ON(PageSlab(page)) checks to make sure that slab pages
are not inadvertently mapped. Otherwise, there must be some bugs in the
kernel.
Reported-by: syzbot+fcf1a817ceb50935ce99@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/lkml/000000000000258e5e05fae79fc1@google.com/ [1]
Fixes: df4e817b71 ("mm: page table check")
Cc: <stable@vger.kernel.org> # 5.17
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Acked-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Link: https://lore.kernel.org/r/20230515130958.32471-5-lrh2000@pku.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0143d148d1 upstream.
The current implementation of usbdev_mmap uses usb_alloc_coherent to
allocate memory pages that will later be mapped into the user space.
Meanwhile, usb_alloc_coherent employs three different methods to
allocate memory, as outlined below:
* If hcd->localmem_pool is non-null, it uses gen_pool_dma_alloc to
allocate memory;
* If DMA is not available, it uses kmalloc to allocate memory;
* Otherwise, it uses dma_alloc_coherent.
However, it should be noted that gen_pool_dma_alloc does not guarantee
that the resulting memory will be page-aligned. Furthermore, trying to
map slab pages (i.e., memory allocated by kmalloc) into the user space
is not resonable and can lead to problems, such as a type confusion bug
when PAGE_TABLE_CHECK=y [1].
To address these issues, this patch introduces hcd_alloc_coherent_pages,
which addresses the above two problems. Specifically,
hcd_alloc_coherent_pages uses gen_pool_dma_alloc_align instead of
gen_pool_dma_alloc to ensure that the memory is page-aligned. To replace
kmalloc, hcd_alloc_coherent_pages directly allocates pages by calling
__get_free_pages.
Reported-by: syzbot+fcf1a817ceb50935ce99@syzkaller.appspotmail.comm
Closes: https://lore.kernel.org/lkml/000000000000258e5e05fae79fc1@google.com/ [1]
Fixes: f7d34b445a ("USB: Add support for usbfs zerocopy.")
Fixes: ff2437befd ("usb: host: Fix excessive alignment restriction for local memory allocations")
Cc: stable@vger.kernel.org
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230515130958.32471-2-lrh2000@pku.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe2ccc6c29 upstream.
Since commit ec6cef9cd9 ("Bluetooth: Fix SMP channel registration for
unconfigured controllers") the debugfs interface for unconfigured
controllers will be created when the controller is configured.
There is however currently nothing preventing a controller from being
configured multiple time (e.g. setting the device address using btmgmt)
which results in failed attempts to register the already registered
debugfs entries:
debugfs: File 'features' in directory 'hci0' already present!
debugfs: File 'manufacturer' in directory 'hci0' already present!
debugfs: File 'hci_version' in directory 'hci0' already present!
...
debugfs: File 'quirk_simultaneous_discovery' in directory 'hci0' already present!
Add a controller flag to avoid trying to register the debugfs interface
more than once.
Fixes: ec6cef9cd9 ("Bluetooth: Fix SMP channel registration for unconfigured controllers")
Cc: stable@vger.kernel.org # 4.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 886bc7d6ed ]
rtm_tca_policy is used from net/sched/sch_api.c and net/sched/cls_api.c,
thus should be declared in an include file.
This fixes the following sparse warning:
net/sched/sch_api.c:1434:25: warning: symbol 'rtm_tca_policy' was not declared. Should it be static?
Fixes: e331473fee ("net/sched: cls_api: add missing validation of netlink attributes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c3b74a92a ]
Add READ_ONCE()/WRITE_ONCE() on accesses to the sock flow table.
This also prevents a (smart ?) compiler to remove the condition in:
if (table->ents[index] != newval)
table->ents[index] = newval;
We need the condition to avoid dirtying a shared cache line.
Fixes: fec5e652e5 ("rfs: Receive Flow Steering")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e5c647c3f ]
Add READ_ONCE()/WRITE_ONCE() on accesses to sk->sk_rxhash.
This also prevents a (smart ?) compiler to remove the condition in:
if (sk->sk_rxhash != newval)
sk->sk_rxhash = newval;
We need the condition to avoid dirtying a shared cache line.
Fixes: fec5e652e5 ("rfs: Receive Flow Steering")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2f4c143d7 ]
A remote DoS vulnerability of RPL Source Routing is assigned CVE-2023-2156.
The Source Routing Header (SRH) has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Header | Hdr Ext Len | Routing Type | Segments Left |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CmprI | CmprE | Pad | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. .
. Addresses[1..n] .
. .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The originator of an SRH places the first hop's IPv6 address in the IPv6
header's IPv6 Destination Address and the second hop's IPv6 address as
the first address in Addresses[1..n].
The CmprI and CmprE fields indicate the number of prefix octets that are
shared with the IPv6 Destination Address. When CmprI or CmprE is not 0,
Addresses[1..n] are compressed as follows:
1..n-1 : (16 - CmprI) bytes
n : (16 - CmprE) bytes
Segments Left indicates the number of route segments remaining. When the
value is not zero, the SRH is forwarded to the next hop. Its address
is extracted from Addresses[n - Segment Left + 1] and swapped with IPv6
Destination Address.
When Segment Left is greater than or equal to 2, the size of SRH is not
changed because Addresses[1..n-1] are decompressed and recompressed with
CmprI.
OTOH, when Segment Left changes from 1 to 0, the new SRH could have a
different size because Addresses[1..n-1] are decompressed with CmprI and
recompressed with CmprE.
Let's say CmprI is 15 and CmprE is 0. When we receive SRH with Segment
Left >= 2, Addresses[1..n-1] have 1 byte for each, and Addresses[n] has
16 bytes. When Segment Left is 1, Addresses[1..n-1] is decompressed to
16 bytes and not recompressed. Finally, the new SRH will need more room
in the header, and the size is (16 - 1) * (n - 1) bytes.
Here the max value of n is 255 as Segment Left is u8, so in the worst case,
we have to allocate 3825 bytes in the skb headroom. However, now we only
allocate a small fixed buffer that is IPV6_RPL_SRH_WORST_SWAP_SIZE (16 + 7
bytes). If the decompressed size overflows the room, skb_push() hits BUG()
below [0].
Instead of allocating the fixed buffer for every packet, let's allocate
enough headroom only when we receive SRH with Segment Left 1.
[0]:
skbuff: skb_under_panic: text:ffffffff81c9f6e2 len:576 put:576 head:ffff8880070b5180 data:ffff8880070b4fb0 tail:0x70 end:0x140 dev:lo
kernel BUG at net/core/skbuff.c:200!
invalid opcode: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 154 Comm: python3 Not tainted 6.4.0-rc4-00190-gc308e9ec0047 #7
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:skb_panic (net/core/skbuff.c:200)
Code: 4f 70 50 8b 87 bc 00 00 00 50 8b 87 b8 00 00 00 50 ff b7 c8 00 00 00 4c 8b 8f c0 00 00 00 48 c7 c7 80 6e 77 82 e8 ad 8b 60 ff <0f> 0b 66 66 2e 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90
RSP: 0018:ffffc90000003da0 EFLAGS: 00000246
RAX: 0000000000000085 RBX: ffff8880058a6600 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff88807dc1c540 RDI: ffff88807dc1c540
RBP: ffffc90000003e48 R08: ffffffff82b392c8 R09: 00000000ffffdfff
R10: ffffffff82a592e0 R11: ffffffff82b092e0 R12: ffff888005b1c800
R13: ffff8880070b51b8 R14: ffff888005b1ca18 R15: ffff8880070b5190
FS: 00007f4539f0b740(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055670baf3000 CR3: 0000000005b0e000 CR4: 00000000007506f0
PKRU: 55555554
Call Trace:
<IRQ>
skb_push (net/core/skbuff.c:210)
ipv6_rthdr_rcv (./include/linux/skbuff.h:2880 net/ipv6/exthdrs.c:634 net/ipv6/exthdrs.c:718)
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:437 (discriminator 5))
ip6_input_finish (./include/linux/rcupdate.h:805 net/ipv6/ip6_input.c:483)
__netif_receive_skb_one_core (net/core/dev.c:5494)
process_backlog (./include/linux/rcupdate.h:805 net/core/dev.c:5934)
__napi_poll (net/core/dev.c:6496)
net_rx_action (net/core/dev.c:6565 net/core/dev.c:6696)
__do_softirq (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/irq.h:142 kernel/softirq.c:572)
do_softirq (kernel/softirq.c:472 kernel/softirq.c:459)
</IRQ>
<TASK>
__local_bh_enable_ip (kernel/softirq.c:396)
__dev_queue_xmit (net/core/dev.c:4272)
ip6_finish_output2 (./include/net/neighbour.h:544 net/ipv6/ip6_output.c:134)
rawv6_sendmsg (./include/net/dst.h:458 ./include/linux/netfilter.h:303 net/ipv6/raw.c:656 net/ipv6/raw.c:914)
sock_sendmsg (net/socket.c:724 net/socket.c:747)
__sys_sendto (net/socket.c:2144)
__x64_sys_sendto (net/socket.c:2156 net/socket.c:2152 net/socket.c:2152)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
RIP: 0033:0x7f453a138aea
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffcc212a1c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007ffcc212a288 RCX: 00007f453a138aea
RDX: 0000000000000060 RSI: 00007f4539084c20 RDI: 0000000000000003
RBP: 00007f4538308e80 R08: 00007ffcc212a300 R09: 000000000000001c
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: ffffffffc4653600 R14: 0000000000000001 R15: 00007f4539712d1b
</TASK>
Modules linked in:
Fixes: 8610c7c6e3 ("net: ipv6: add support for rpl sr exthdr")
Reported-by: Max VA
Closes: https://www.interruptlabs.co.uk/articles/linux-ipv6-route-of-death
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230605180617.67284-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1857c19941 ]
When the HCI_UNREGISTER flag is set, no jobs should be scheduled. Fix
potential race when HCI_UNREGISTER is set after the flag is tested in
hci_cmd_sync_queue.
Fixes: 0b94f2651f ("Bluetooth: hci_sync: Fix queuing commands when HCI_UNREGISTER is set")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf2e1d201 ]
skip_notify_on_dev_down ctl table expects this field
to be an int (4 bytes), not a bool (1 byte).
Because proc_dou8vec_minmax() was added in 5.13,
this patch converts skip_notify_on_dev_down to an int.
Following patch then converts the field to u8 and use proc_dou8vec_minmax().
Fixes: 7c6bb7d2fa ("net/ipv6: Add knob to skip DELROUTE message on device down")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e209fee411 ]
With this commit, all the GIDs ("0 4294967294") can be written to the
"net.ipv4.ping_group_range" sysctl.
Note that 4294967295 (0xffffffff) is an invalid GID (see gid_valid() in
include/linux/uidgid.h), and an attempt to register this number will cause
-EINVAL.
Prior to this commit, only up to GID 2147483647 could be covered.
Documentation/networking/ip-sysctl.rst had "0 4294967295" as an example
value, but this example was wrong and causing -EINVAL.
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Co-developed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Akihiro Suda <akihiro.suda.cz@hco.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed779fe4c9 ]
After the blamed commit, the member key is longer 4-byte aligned. On
platforms that do not support unaligned access, e.g., MIPS32R2 with
unaligned_action set to 1, this will trigger a crash when accessing
an IPv6 pneigh_entry, as the key is cast to an in6_addr pointer.
Change the type of the key to u32 to make it aligned.
Fixes: 62dd93181a ("[IPV6] NDISC: Set per-entry is_router flag in Proxy NA.")
Signed-off-by: Qingfang DENG <qingfang.deng@siflower.com.cn>
Link: https://lore.kernel.org/r/20230601015432.159066-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 627bb528b0 ]
dvb_register_device() dynamically allocates fops with kmemdup()
to set the fops->owner.
And these fops are registered in 'file->f_ops' using replace_fops()
in the dvb_device_open() process, and kfree()d in dvb_free_device().
However, it is not common to use dynamically allocated fops instead
of 'static const' fops as an argument of replace_fops(),
and UAF may occur.
These UAFs can occur on any dvb type using dvb_register_device(),
such as dvb_dvr, dvb_demux, dvb_frontend, dvb_net, etc.
So, instead of kfree() the fops dynamically allocated in
dvb_register_device() in dvb_free_device() called during the
.disconnect() process, kfree() it collectively in exit_dvbdev()
called when the dvbdev.c module is removed.
Link: https://lore.kernel.org/linux-media/20221117045925.14297-4-imv4bel@gmail.com
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4172385b0c ]
A race condition may occur between the .disconnect function, which
is called when the device is disconnected, and the dvb_device_open()
function, which is called when the device node is open()ed.
This results in several types of UAFs.
The root cause of this is that you use the dvb_device_open() function,
which does not implement a conditional statement
that checks 'dvbnet->exit'.
So, add 'remove_mutex` to protect 'dvbnet->exit' and use
locked_dvb_net_open() function to check 'dvbnet->exit'.
[mchehab: fix a checkpatch warning]
Link: https://lore.kernel.org/linux-media/20221117045925.14297-3-imv4bel@gmail.com
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30c6f0bf95 ]
In this patch, we mainly try to handle sending a compressed ack
correctly if it's deferred.
Here are more details in the old logic:
When sack compression is triggered in the tcp_compressed_ack_kick(),
if the sock is owned by user, it will set TCP_DELACK_TIMER_DEFERRED
and then defer to the release cb phrase. Later once user releases
the sock, tcp_delack_timer_handler() should send a ack as expected,
which, however, cannot happen due to lack of ICSK_ACK_TIMER flag.
Therefore, the receiver would not sent an ack until the sender's
retransmission timeout. It definitely increases unnecessary latency.
Fixes: 5d9f4262b7 ("tcp: add SACK compression")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: fuyuanli <fuyuanli@didiglobal.com>
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://lore.kernel.org/netdev/20230529113804.GA20300@didi-ThinkCentre-M920t-N000/
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230531080150.GA20424@didi-ThinkCentre-M920t-N000
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c034203b6a ]
The bug here is that you cannot rely on getting the same socket
from multiple calls to fget() because userspace can influence
that. This is a kind of double fetch bug.
The fix is to delete the svc_alien_sock() function and instead do
the checking inside the svc_addsock() function.
Fixes: 3064639423 ("nfsd: check passed socket's net matches NFSd superblock's one")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: NeilBrown <neilb@suse.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 368d3cb406 ]
page_pool_ring_[un]lock() use in_softirq() to decide which
spin lock variant to use, and when they are called in the
context with in_softirq() being false, spin_lock_bh() is
called in page_pool_ring_lock() while spin_unlock() is
called in page_pool_ring_unlock(), because spin_lock_bh()
has disabled the softirq in page_pool_ring_lock(), which
causes inconsistency for spin lock pair calling.
This patch fixes it by returning in_softirq state from
page_pool_producer_lock(), and use it to decide which
spin lock variant to use in page_pool_producer_unlock().
As pool->ring has both producer and consumer lock, so
rename it to page_pool_producer_[un]lock() to reflect
the actual usage. Also move them to page_pool.c as they
are only used there, and remove the 'inline' as the
compiler may have better idea to do inlining or not.
Fixes: 7886244736 ("net: page_pool: Add bulk support for ptr_ring")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/r/20230522031714.5089-1-linyunsheng@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 542bcea4be ]
We use BH context only for synchronization, so we don't care if it's
actually serving softirq or not.
As a side node, in case of threaded NAPI, in_serving_softirq() will
return false because it's in process context with BH off, making
page_pool_recycle_in_cache() unreachable.
Signed-off-by: Qingfang DENG <qingfang.deng@siflower.com.cn>
Tested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 368d3cb406 ("page_pool: fix inconsistency for page_pool_ring_[un]lock()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5c6de5fa0 ]
The read_skb() logic is incrementing the tcp->copied_seq which is used for
among other things calculating how many outstanding bytes can be read by
the application. This results in application errors, if the application
does an ioctl(FIONREAD) we return zero because this is calculated from
the copied_seq value.
To fix this we move tcp->copied_seq accounting into the recv handler so
that we update these when the recvmsg() hook is called and data is in
fact copied into user buffers. This gives an accurate FIONREAD value
as expected and improves ACK handling. Before we were calling the
tcp_rcv_space_adjust() which would update 'number of bytes copied to
user in last RTT' which is wrong for programs returning SK_PASS. The
bytes are only copied to the user when recvmsg is handled.
Doing the fix for recvmsg is straightforward, but fixing redirect and
SK_DROP pkts is a bit tricker. Build a tcp_psock_eat() helper and then
call this from skmsg handlers. This fixes another issue where a broken
socket with a BPF program doing a resubmit could hang the receiver. This
happened because although read_skb() consumed the skb through sock_drop()
it did not update the copied_seq. Now if a single reccv socket is
redirecting to many sockets (for example for lb) the receiver sk will be
hung even though we might expect it to continue. The hang comes from
not updating the copied_seq numbers and memory pressure resulting from
that.
We have a slight layer problem of calling tcp_eat_skb even if its not
a TCP socket. To fix we could refactor and create per type receiver
handlers. I decided this is more work than we want in the fix and we
already have some small tweaks depending on caller that use the
helper skb_bpf_strparser(). So we extend that a bit and always set
the strparser bit when it is in use and then we can gate the
seq_copied updates on this.
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-9-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 405df89dd5 ]
We noticed some rare sk_buffs were stepping past the queue when system was
under memory pressure. The general theory is to skip enqueueing
sk_buffs when its not necessary which is the normal case with a system
that is properly provisioned for the task, no memory pressure and enough
cpu assigned.
But, if we can't allocate memory due to an ENOMEM error when enqueueing
the sk_buff into the sockmap receive queue we push it onto a delayed
workqueue to retry later. When a new sk_buff is received we then check
if that queue is empty. However, there is a problem with simply checking
the queue length. When a sk_buff is being processed from the ingress queue
but not yet on the sockmap msg receive queue its possible to also recv
a sk_buff through normal path. It will check the ingress queue which is
zero and then skip ahead of the pkt being processed.
Previously we used sock lock from both contexts which made the problem
harder to hit, but not impossible.
To fix instead of popping the skb from the queue entirely we peek the
skb from the queue and do the copy there. This ensures checks to the
queue length are non-zero while skb is being processed. Then finally
when the entire skb has been copied to user space queue or another
socket we pop it off the queue. This way the queue length check allows
bypassing the queue only after the list has been completely processed.
To reproduce issue we run NGINX compliance test with sockmap running and
observe some flakes in our testing that we attributed to this issue.
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: William Findlay <will@isovalent.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-5-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29173d07f7 ]
Sk_buffs are fed into sockmap verdict programs either from a strparser
(when the user might want to decide how framing of skb is done by attaching
another parser program) or directly through tcp_read_sock. The
tcp_read_sock is the preferred method for performance when the BPF logic is
a stream parser.
The flow for Cilium's common use case with a stream parser is,
tcp_read_sock()
sk_psock_verdict_recv
ret = bpf_prog_run_pin_on_cpu()
sk_psock_verdict_apply(sock, skb, ret)
// if system is under memory pressure or app is slow we may
// need to queue skb. Do this queuing through ingress_skb and
// then kick timer to wake up handler
skb_queue_tail(ingress_skb, skb)
schedule_work(work);
The work queue is wired up to sk_psock_backlog(). This will then walk the
ingress_skb skb list that holds our sk_buffs that could not be handled,
but should be OK to run at some later point. However, its possible that
the workqueue doing this work still hits an error when sending the skb.
When this happens the skbuff is requeued on a temporary 'state' struct
kept with the workqueue. This is necessary because its possible to
partially send an skbuff before hitting an error and we need to know how
and where to restart when the workqueue runs next.
Now for the trouble, we don't rekick the workqueue. This can cause a
stall where the skbuff we just cached on the state variable might never
be sent. This happens when its the last packet in a flow and no further
packets come along that would cause the system to kick the workqueue from
that side.
To fix we could do simple schedule_work(), but while under memory pressure
it makes sense to back off some instead of continue to retry repeatedly. So
instead to fix convert schedule_work to schedule_delayed_work and add
backoff logic to reschedule from backlog queue on errors. Its not obvious
though what a good backoff is so use '1'.
To test we observed some flakes whil running NGINX compliance test with
sockmap we attributed these failed test to this bug and subsequent issue.
>From on list discussion. This commit
bec217197b41("skmsg: Schedule psock work if the cached skb exists on the psock")
was intended to address similar race, but had a couple cases it missed.
Most obvious it only accounted for receiving traffic on the local socket
so if redirecting into another socket we could still get an sk_buff stuck
here. Next it missed the case where copied=0 in the recv() handler and
then we wouldn't kick the scheduler. Also its sub-optimal to require
userspace to kick the internal mechanisms of sockmap to wake it up and
copy data to user. It results in an extra syscall and requires the app
to actual handle the EAGAIN correctly.
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: William Findlay <will@isovalent.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-3-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eca9bfafee ]
When receive buffer is small we try to copy out the data from
TCP into a skb maintained by TLS to prevent connection from
stalling. Unfortunately if a single record is made up of a mix
of decrypted and non-decrypted skbs combining them into a single
skb leads to loss of decryption status, resulting in decryption
errors or data corruption.
Similarly when trying to use TCP receive queue directly we need
to make sure that all the skbs within the record have the same
status. If we don't the mixed status will be detected correctly
but we'll CoW the anchor, again collapsing it into a single paged
skb without decrypted status preserved. So the "fixup" code will
not know which parts of skb to re-encrypt.
Fixes: 84c61fe1a7 ("tls: rx: do not use the standard strparser")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14c4be92eb ]
If a record is partially decrypted we'll have to CoW it, anyway,
so go into copy mode and allocate a writable skb right away.
This will make subsequent fix simpler because we won't have to
teach tls_strp_msg_make_copy() how to copy skbs while preserving
decrypt status.
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: eca9bfafee ("tls: rx: strp: preserve decryption status of skbs when needed")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3632679d9e ]
With a raw socket bound to IPPROTO_RAW (ie with hdrincl enabled), the
protocol field of the flow structure, build by raw_sendmsg() /
rawv6_sendmsg()), is set to IPPROTO_RAW. This breaks the ipsec policy
lookup when some policies are defined with a protocol in the selector.
For ipv6, the sin6_port field from 'struct sockaddr_in6' could be used to
specify the protocol. Just accept all values for IPPROTO_RAW socket.
For ipv4, the sin_port field of 'struct sockaddr_in' could not be used
without breaking backward compatibility (the value of this field was never
checked). Let's add a new kind of control message, so that the userland
could specify which protocol is used.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
CC: stable@vger.kernel.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20230522120820.1319391-1-nicolas.dichtel@6wind.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91d0b78c51 ]
Users who want to share a single public IP address for outgoing connections
between several hosts traditionally reach for SNAT. However, SNAT requires
state keeping on the node(s) performing the NAT.
A stateless alternative exists, where a single IP address used for egress
can be shared between several hosts by partitioning the available ephemeral
port range. In such a setup:
1. Each host gets assigned a disjoint range of ephemeral ports.
2. Applications open connections from the host-assigned port range.
3. Return traffic gets routed to the host based on both, the destination IP
and the destination port.
An application which wants to open an outgoing connection (connect) from a
given port range today can choose between two solutions:
1. Manually pick the source port by bind()'ing to it before connect()'ing
the socket.
This approach has a couple of downsides:
a) Search for a free port has to be implemented in the user-space. If
the chosen 4-tuple happens to be busy, the application needs to retry
from a different local port number.
Detecting if 4-tuple is busy can be either easy (TCP) or hard
(UDP). In TCP case, the application simply has to check if connect()
returned an error (EADDRNOTAVAIL). That is assuming that the local
port sharing was enabled (REUSEADDR) by all the sockets.
# Assume desired local port range is 60_000-60_511
s = socket(AF_INET, SOCK_STREAM)
s.setsockopt(SOL_SOCKET, SO_REUSEADDR, 1)
s.bind(("192.0.2.1", 60_000))
s.connect(("1.1.1.1", 53))
# Fails only if 192.0.2.1:60000 -> 1.1.1.1:53 is busy
# Application must retry with another local port
In case of UDP, the network stack allows binding more than one socket
to the same 4-tuple, when local port sharing is enabled
(REUSEADDR). Hence detecting the conflict is much harder and involves
querying sock_diag and toggling the REUSEADDR flag [1].
b) For TCP, bind()-ing to a port within the ephemeral port range means
that no connecting sockets, that is those which leave it to the
network stack to find a free local port at connect() time, can use
the this port.
IOW, the bind hash bucket tb->fastreuse will be 0 or 1, and the port
will be skipped during the free port search at connect() time.
2. Isolate the app in a dedicated netns and use the use the per-netns
ip_local_port_range sysctl to adjust the ephemeral port range bounds.
The per-netns setting affects all sockets, so this approach can be used
only if:
- there is just one egress IP address, or
- the desired egress port range is the same for all egress IP addresses
used by the application.
For TCP, this approach avoids the downsides of (1). Free port search and
4-tuple conflict detection is done by the network stack:
system("sysctl -w net.ipv4.ip_local_port_range='60000 60511'")
s = socket(AF_INET, SOCK_STREAM)
s.setsockopt(SOL_IP, IP_BIND_ADDRESS_NO_PORT, 1)
s.bind(("192.0.2.1", 0))
s.connect(("1.1.1.1", 53))
# Fails if all 4-tuples 192.0.2.1:60000-60511 -> 1.1.1.1:53 are busy
For UDP this approach has limited applicability. Setting the
IP_BIND_ADDRESS_NO_PORT socket option does not result in local source
port being shared with other connected UDP sockets.
Hence relying on the network stack to find a free source port, limits the
number of outgoing UDP flows from a single IP address down to the number
of available ephemeral ports.
To put it another way, partitioning the ephemeral port range between hosts
using the existing Linux networking API is cumbersome.
To address this use case, add a new socket option at the SOL_IP level,
named IP_LOCAL_PORT_RANGE. The new option can be used to clamp down the
ephemeral port range for each socket individually.
The option can be used only to narrow down the per-netns local port
range. If the per-socket range lies outside of the per-netns range, the
latter takes precedence.
UAPI-wise, the low and high range bounds are passed to the kernel as a pair
of u16 values in host byte order packed into a u32. This avoids pointer
passing.
PORT_LO = 40_000
PORT_HI = 40_511
s = socket(AF_INET, SOCK_STREAM)
v = struct.pack("I", PORT_HI << 16 | PORT_LO)
s.setsockopt(SOL_IP, IP_LOCAL_PORT_RANGE, v)
s.bind(("127.0.0.1", 0))
s.getsockname()
# Local address between ("127.0.0.1", 40_000) and ("127.0.0.1", 40_511),
# if there is a free port. EADDRINUSE otherwise.
[1] 232b432c1d/2022-02-connectx/connectx.py (L116)
Reviewed-by: Marek Majkowski <marek@cloudflare.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 3632679d9e ("ipv{4,6}/raw: fix output xfrm lookup wrt protocol")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c7dd225bc2 upstream.
SW Steering uses RC QP for writing STEs to ICM. This writingis done in LB
(loopback), and FL (force-loopback) QP is preferred for performance. FL is
available when RoCE is enabled or disabled based on RoCE caps.
This patch adds reading of FL capability from HCA caps in addition to the
existing reading from RoCE caps, thus fixing the case where we didn't
have loopback enabled when RoCE was disabled.
Fixes: 7304d603a5 ("net/mlx5: DR, Add support for force-loopback QP")
Signed-off-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9510965747 upstream.
Constant 'C4_CHANNEL' does not exist on the firmware side. Value 0xC is
reserved for 'C7_1' instead.
Fixes: 04afbbbb1c ("ASoC: Intel: Skylake: Update the topology interface structure")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 335b422346 upstream.
Commit bf5e758f02 ("genirq/msi: Simplify sysfs handling") reworked the
creation of sysfs entries for MSI IRQs. The creation used to be in
msi_domain_alloc_irqs_descs_locked after calling ops->domain_alloc_irqs.
Then it moved into __msi_domain_alloc_irqs which is an implementation of
domain_alloc_irqs. However, Xen comes with the only other implementation
of domain_alloc_irqs and hence doesn't run the sysfs population code
anymore.
Commit 6c796996ee ("x86/pci/xen: Fixup fallout from the PCI/MSI
overhaul") set the flag MSI_FLAG_DEV_SYSFS for the xen msi_domain_info
but that doesn't actually have an effect because Xen uses it's own
domain_alloc_irqs implementation.
Fix this by making use of the fallback functions for sysfs population.
Fixes: bf5e758f02 ("genirq/msi: Simplify sysfs handling")
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20230503131656.15928-1-mheyne@amazon.de
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f15afbd34d upstream.
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. It was spotted by UBSAN.
So let's just fix this by using the BIT() helper for all SB_* flags.
Fixes: e462ec50cb ("VFS: Differentiate mount flags (MS_*) from internal superblock flags")
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Message-Id: <20230424051835.374204-1-gehao@kylinos.cn>
[brauner@kernel.org: use BIT() for all SB_* flags]
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19b8766459 upstream.
Each physical partition can provide multiple services each with UUID.
Each such service can be presented as logical partition with a unique
combination of VM ID and UUID. The number of distinct UUID in a system
will be less than or equal to the number of logical partitions.
However, currently it fails to register more than one logical partition
or service within a physical partition as the device name contains only
VM ID while both VM ID and UUID are maintained in the partition information.
The kernel complains with the below message:
| sysfs: cannot create duplicate filename '/devices/arm-ffa-8001'
| CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7 #8
| Hardware name: FVP Base RevC (DT)
| Call trace:
| dump_backtrace+0xf8/0x118
| show_stack+0x18/0x24
| dump_stack_lvl+0x50/0x68
| dump_stack+0x18/0x24
| sysfs_create_dir_ns+0xe0/0x13c
| kobject_add_internal+0x220/0x3d4
| kobject_add+0x94/0x100
| device_add+0x144/0x5d8
| device_register+0x20/0x30
| ffa_device_register+0x88/0xd8
| ffa_setup_partitions+0x108/0x1b8
| ffa_init+0x2ec/0x3a4
| do_one_initcall+0xcc/0x240
| do_initcall_level+0x8c/0xac
| do_initcalls+0x54/0x94
| do_basic_setup+0x1c/0x28
| kernel_init_freeable+0x100/0x16c
| kernel_init+0x20/0x1a0
| ret_from_fork+0x10/0x20
| kobject_add_internal failed for arm-ffa-8001 with -EEXIST, don't try to
| register things with the same name in the same directory.
| arm_ffa arm-ffa: unable to register device arm-ffa-8001 err=-17
| ARM FF-A: ffa_setup_partitions: failed to register partition ID 0x8001
By virtue of being random enough to avoid collisions when generated in a
distributed system, there is no way to compress UUID keys to the number
of bits required to identify each. We can eliminate '-' in the name but
it is not worth eliminating 4 bytes and add unnecessary logic for doing
that. Also v1.0 doesn't provide the UUID of the partitions which makes
it hard to use the same for the device name.
So to keep it simple, let us alloc an ID using ida_alloc() and append the
same to "arm-ffa" to make up a unique device name. Also stash the id value
in ffa_dev to help freeing the ID later when the device is destroyed.
Fixes: e781858488 ("firmware: arm_ffa: Add initial FFA bus support for device enumeration")
Reported-by: Lucian Paul-Trifu <lucian.paul-trifu@arm.com>
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-3-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 939a116142 upstream.
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c00bc80462 upstream.
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa8118 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c21f11d182 upstream.
In mutex_init() lockdep identifies a lock by defining a special static
key for each lock class. However if we wrap the macro in a function,
like in drmm_mutex_init(), we end up generating:
int drmm_mutex_init(struct drm_device *dev, struct mutex *lock)
{
static struct lock_class_key __key;
__mutex_init((lock), "lock", &__key);
....
}
The static __key here is what lockdep uses to identify the lock class,
however since this is just a normal function the key here will be
created once, where all callers then use the same key. In effect the
mutex->depmap.key will be the same pointer for different
drmm_mutex_init() callers. This then results in impossible lockdep
splats since lockdep thinks completely unrelated locks are the same lock
class.
To fix this turn drmm_mutex_init() into a macro such that it generates a
different "static struct lock_class_key __key" for each invocation,
which looks to be inline with what mutex_init() wants.
v2:
- Revamp the commit message with clearer explanation of the issue.
- Rather export __drmm_mutex_release() than static inline.
Reported-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reported-by: Sarah Walker <sarah.walker@imgtec.com>
Fixes: e13f13e039 ("drm: Add DRM-managed mutex_init()")
Cc: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Jocelyn Falempe <jfalempe@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230519090733.489019-1-matthew.auld@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1389062650 upstream.
Many of the older USB drivers in the Linux USB stack were written
based simply on a vendor's device specification. They use the
endpoint information in the spec and assume these endpoints will
always be present, with the properties listed, in any device matching
the given vendor and product IDs.
While that may have been true back then, with spoofing and fuzzing it
is not true any more. More and more we are finding that those old
drivers need to perform at least a minimum of checking before they try
to use any endpoint other than ep0.
To make this checking as simple as possible, we now add a couple of
utility routines to the USB core. usb_check_bulk_endpoints() and
usb_check_int_endpoints() take an interface pointer together with a
list of endpoint addresses (numbers and directions). They check that
the interface's current alternate setting includes endpoints with
those addresses and that each of these endpoints has the right type:
bulk or interrupt, respectively.
Although we already have usb_find_common_endpoints() and related
routines meant for a similar purpose, they are not well suited for
this kind of checking. Those routines find endpoints of various
kinds, but only one (either the first or the last) of each kind, and
they don't verify that the endpoints' addresses agree with what the
caller expects.
In theory the new routines could be more general: They could take a
particular altsetting as their argument instead of always using the
interface's current altsetting. In practice I think this won't matter
too much; multiple altsettings tend to be used for transferring media
(audio or visual) over isochronous endpoints, not bulk or interrupt.
Drivers for such devices will generally require more sophisticated
checking than these simplistic routines provide.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/dd2c8e8c-2c87-44ea-ba17-c64b97e201c9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae9b15fbe6 upstream.
When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.
team0
|
+------+------+-----+-----+
| | | | |
team1 team2 team3 ... team200
If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.
But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.
Reproducer:
ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
ip link add team$i master team0 type team
ethtool -K team$i lro on
done
ethtool -K team0 lro off
In order to fix it, the notifier_ctx member of bonding/team is introduced.
Reported-by: syzbot+60748c96cf5c6df8e581@syzkaller.appspotmail.com
Fixes: fd867d51f8 ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230517143010.3596250-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99d4645062 ]
Set TPM_CHIP_FLAG_SUSPENDED in tpm_pm_suspend() and reset in
tpm_pm_resume(). While the flag is set, tpm_hwrng() gives back zero
bytes. This prevents hwrng from racing during resume.
Cc: stable@vger.kernel.org
Fixes: 6e592a065d ("tpm: Move Linux RNG connection to hwrng")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c8862de05 ]
TPM chip bootstrapping was removed from tpm_chip_register(), and it
was relocated to tpm_tis_core. This breaks all drivers which are not
based on tpm_tis because the chip will not get properly initialized.
Take the corrective steps:
1. Rename tpm_chip_startup() as tpm_chip_bootstrap() and make it one-shot.
2. Call tpm_chip_bootstrap() in tpm_chip_register(), which reverts the
things as tehy used to be.
Cc: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Fixes: 548eb516ec ("tpm, tpm_tis: startup chip before testing for interrupts")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/all/ZEjqhwHWBnxcaRV5@xpf.sh.intel.com/
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 99d4645062 ("tpm: Prevent hwrng from activating during resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 948f072ada ]
Since the ->xprt_ctxt pointer was added to svc_deferred_req, it has not
been sufficient to use kfree() to free a deferred request. We may need
to free the ctxt as well.
As freeing the ctxt is all that ->xpo_release_rqst() does, we repurpose
it to explicit do that even when the ctxt is not stored in an rqst.
So we now have ->xpo_release_ctxt() which is given an xprt and a ctxt,
which may have been taken either from an rqst or from a dreq. The
caller is now responsible for clearing that pointer after the call to
->xpo_release_ctxt.
We also clear dr->xprt_ctxt when the ctxt is moved into a new rqst when
revisiting a deferred request. This ensures there is only one pointer
to the ctxt, so the risk of double freeing in future is reduced. The
new code in svc_xprt_release which releases both the ctxt and any
rq_deferred depends on this.
Fixes: 773f91b2cf ("SUNRPC: Fix NFSD's request deferral on RDMA transports")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c5a7680e6 ]
struct platform_driver::remove returning an integer made driver authors
expect that returning an error code was proper error handling. However
the driver core ignores the error and continues to remove the device
because there is nothing the core could do anyhow and reentering the
remove callback again is only calling for trouble.
So this is an source for errors typically yielding resource leaks in the
error path.
As there are too many platform drivers to neatly convert them all to
return void in a single go, do it in several steps after this patch:
a) Convert all drivers to implement .remove_new() returning void instead
of .remove() returning int;
b) Change struct platform_driver::remove() to return void and so make
it identical to .remove_new();
c) Change all drivers back to .remove() now with the better prototype;
d) drop struct platform_driver::remove_new().
While this touches all drivers eventually twice, steps a) and c) can be
done one driver after another and so reduces coordination efforts
immensely and simplifies review.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221209150914.3557650-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 17955aba78 ("ASoC: fsl_micfil: Fix error handler with pm_runtime_enable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0b081d17a ]
With KCSAN enabled, end_of_stack() can get out-of-lined. Force it
inline.
Fixes the following warnings:
vmlinux.o: warning: objtool: check_stackleak_irqoff+0x2b: call to end_of_stack() leaves .noinstr.text section
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/cc1b4d73d3a428a00d206242a68fdf99a934ca7b.1681320026.git.jpoimboe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91b6d02ddc ]
The ATS2851 based controller advertises support for command "LE Set Random
Private Address Timeout" but does not actually implement it, impeding the
controller initialization.
Add the quirk HCI_QUIRK_BROKEN_SET_RPA_TIMEOUT to unblock the controller
initialization.
< HCI Command: LE Set Resolvable Private... (0x08|0x002e) plen 2
Timeout: 900 seconds
> HCI Event: Command Status (0x0f) plen 4
LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 1
Status: Unknown HCI Command (0x01)
Co-developed-by: imoc <wzj9912@gmail.com>
Signed-off-by: imoc <wzj9912@gmail.com>
Signed-off-by: Raul Cheleguini <raul.cheleguini@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8194f1ef5a ]
Some adapters (e.g. RTL8723CS) advertise that they have more than
2 pages for local ext features, but they don't support any features
declared in these pages. RTL8723CS reports max_page = 2 and declares
support for sync train and secure connection, but it responds with
either garbage or with error in status on corresponding commands.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3478c68f6 ]
In ip_vs_sync_conn_v0() copy is made to struct ip_vs_sync_conn_options.
That structure looks like this:
struct ip_vs_sync_conn_options {
struct ip_vs_seq in_seq;
struct ip_vs_seq out_seq;
};
The source of the copy is the in_seq field of struct ip_vs_conn. Whose
type is struct ip_vs_seq. Thus we can see that the source - is not as
wide as the amount of data copied, which is the width of struct
ip_vs_sync_conn_option.
The copy is safe because the next field in is another struct ip_vs_seq.
Make use of struct_group() to annotate this.
Flagged by gcc-13 as:
In file included from ./include/linux/string.h:254,
from ./include/linux/bitmap.h:11,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/paravirt.h:17,
from ./arch/x86/include/asm/cpuid.h:62,
from ./arch/x86/include/asm/processor.h:19,
from ./arch/x86/include/asm/timex.h:5,
from ./include/linux/timex.h:67,
from ./include/linux/time32.h:13,
from ./include/linux/time.h:60,
from ./include/linux/stat.h:19,
from ./include/linux/module.h:13,
from net/netfilter/ipvs/ip_vs_sync.c:38:
In function 'fortify_memcpy_chk',
inlined from 'ip_vs_sync_conn_v0' at net/netfilter/ipvs/ip_vs_sync.c:606:3:
./include/linux/fortify-string.h:529:25: error: call to '__read_overflow2_field' declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror=attribute-warning]
529 | __read_overflow2_field(q_size_field, size);
|
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cc6571f56 ]
When requesting a TX queue at a given index, warn on out-of-bounds
referencing if the index is greater than the allocated number of
queues.
Specifically, since this function is used heavily in the networking
stack use DEBUG_NET_WARN_ON_ONCE to avoid executing a new branch on
every packet.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Link: https://lore.kernel.org/r/20230321150725.127229-2-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35727af2b1 ]
The T241 platform suffers from the T241-FABRIC-4 erratum which causes
unexpected behavior in the GIC when multiple transactions are received
simultaneously from different sources. This hardware issue impacts
NVIDIA server platforms that use more than two T241 chips
interconnected. Each chip has support for 320 {E}SPIs.
This issue occurs when multiple packets from different GICs are
incorrectly interleaved at the target chip. The erratum text below
specifies exactly what can cause multiple transfer packets susceptible
to interleaving and GIC state corruption. GIC state corruption can
lead to a range of problems, including kernel panics, and unexpected
behavior.
>From the erratum text:
"In some cases, inter-socket AXI4 Stream packets with multiple
transfers, may be interleaved by the fabric when presented to ARM
Generic Interrupt Controller. GIC expects all transfers of a packet
to be delivered without any interleaving.
The following GICv3 commands may result in multiple transfer packets
over inter-socket AXI4 Stream interface:
- Register reads from GICD_I* and GICD_N*
- Register writes to 64-bit GICD registers other than GICD_IROUTERn*
- ITS command MOVALL
Multiple commands in GICv4+ utilize multiple transfer packets,
including VMOVP, VMOVI, VMAPP, and 64-bit register accesses."
This issue impacts system configurations with more than 2 sockets,
that require multi-transfer packets to be sent over inter-socket
AXI4 Stream interface between GIC instances on different sockets.
GICv4 cannot be supported. GICv3 SW model can only be supported
with the workaround. Single and Dual socket configurations are not
impacted by this issue and support GICv3 and GICv4."
Link: https://developer.nvidia.com/docs/t241-fabric-4/nvidia-t241-fabric-4-errata.pdf
Writing to the chip alias region of the GICD_In{E} registers except
GICD_ICENABLERn has an equivalent effect as writing to the global
distributor. The SPI interrupt deactivate path is not impacted by
the erratum.
To fix this problem, implement a workaround that ensures read accesses
to the GICD_In{E} registers are directed to the chip that owns the
SPI, and disable GICv4.x features. To simplify code changes, the
gic_configure_irq() function uses the same alias region for both read
and write operations to GICD_ICFGR.
Co-developed-by: Vikram Sethi <vsethi@nvidia.com>
Signed-off-by: Vikram Sethi <vsethi@nvidia.com>
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com> (for SMCCC/SOC ID bits)
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230319024314.3540573-2-sdonthineni@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2c48b2387 ]
Running a preempt-rt (v6.2-rc3-rt1) based kernel on an Ampere Altra
triggers:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46
in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 24, name: cpuhp/0
preempt_count: 0, expected: 0
RCU nest depth: 0, expected: 0
3 locks held by cpuhp/0/24:
#0: ffffda30217c70d0 (cpu_hotplug_lock){++++}-{0:0}, at: cpuhp_thread_fun+0x5c/0x248
#1: ffffda30217c7120 (cpuhp_state-up){+.+.}-{0:0}, at: cpuhp_thread_fun+0x5c/0x248
#2: ffffda3021c711f0 (sdei_list_lock){....}-{3:3}, at: sdei_cpuhp_up+0x3c/0x130
irq event stamp: 36
hardirqs last enabled at (35): [<ffffda301e85b7bc>] finish_task_switch+0xb4/0x2b0
hardirqs last disabled at (36): [<ffffda301e812fec>] cpuhp_thread_fun+0x21c/0x248
softirqs last enabled at (0): [<ffffda301e80b184>] copy_process+0x63c/0x1ac0
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 0 PID: 24 Comm: cpuhp/0 Not tainted 5.19.0-rc3-rt5-[...]
Hardware name: WIWYNN Mt.Jade Server [...]
Call trace:
dump_backtrace+0x114/0x120
show_stack+0x20/0x70
dump_stack_lvl+0x9c/0xd8
dump_stack+0x18/0x34
__might_resched+0x188/0x228
rt_spin_lock+0x70/0x120
sdei_cpuhp_up+0x3c/0x130
cpuhp_invoke_callback+0x250/0xf08
cpuhp_thread_fun+0x120/0x248
smpboot_thread_fn+0x280/0x320
kthread+0x130/0x140
ret_from_fork+0x10/0x20
sdei_cpuhp_up() is called in the STARTING hotplug section,
which runs with interrupts disabled. Use a CPUHP_AP_ONLINE_DYN entry
instead to execute the cpuhp cb later, with preemption enabled.
SDEI originally got its own cpuhp slot to allow interacting
with perf. It got superseded by pNMI and this early slot is not
relevant anymore. [1]
Some SDEI calls (e.g. SDEI_1_0_FN_SDEI_PE_MASK) take actions on the
calling CPU. It is checked that preemption is disabled for them.
_ONLINE cpuhp cb are executed in the 'per CPU hotplug thread'.
Preemption is enabled in those threads, but their cpumask is limited
to 1 CPU.
Move 'WARN_ON_ONCE(preemptible())' statements so that SDEI cpuhp cb
don't trigger them.
Also add a check for the SDEI_1_0_FN_SDEI_PRIVATE_RESET SDEI call
which acts on the calling CPU.
[1]:
https://lore.kernel.org/all/5813b8c5-ae3e-87fd-fccc-94c9cd08816d@arm.com/
Suggested-by: James Morse <james.morse@arm.com>
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20230216084920.144064-1-pierre.gondois@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43b4506326 ]
After a couple of years and multiple LTS releases we received a report
that the behavior of O_DIRECTORY | O_CREAT changed starting with v5.7.
On kernels prior to v5.7 combinations of O_DIRECTORY, O_CREAT, O_EXCL
had the following semantics:
(1) open("/tmp/d", O_DIRECTORY | O_CREAT)
* d doesn't exist: create regular file
* d exists and is a regular file: ENOTDIR
* d exists and is a directory: EISDIR
(2) open("/tmp/d", O_DIRECTORY | O_CREAT | O_EXCL)
* d doesn't exist: create regular file
* d exists and is a regular file: EEXIST
* d exists and is a directory: EEXIST
(3) open("/tmp/d", O_DIRECTORY | O_EXCL)
* d doesn't exist: ENOENT
* d exists and is a regular file: ENOTDIR
* d exists and is a directory: open directory
On kernels since to v5.7 combinations of O_DIRECTORY, O_CREAT, O_EXCL
have the following semantics:
(1) open("/tmp/d", O_DIRECTORY | O_CREAT)
* d doesn't exist: ENOTDIR (create regular file)
* d exists and is a regular file: ENOTDIR
* d exists and is a directory: EISDIR
(2) open("/tmp/d", O_DIRECTORY | O_CREAT | O_EXCL)
* d doesn't exist: ENOTDIR (create regular file)
* d exists and is a regular file: EEXIST
* d exists and is a directory: EEXIST
(3) open("/tmp/d", O_DIRECTORY | O_EXCL)
* d doesn't exist: ENOENT
* d exists and is a regular file: ENOTDIR
* d exists and is a directory: open directory
This is a fairly substantial semantic change that userspace didn't
notice until Pedro took the time to deliberately figure out corner
cases. Since no one noticed this breakage we can somewhat safely assume
that O_DIRECTORY | O_CREAT combinations are likely unused.
The v5.7 breakage is especially weird because while ENOTDIR is returned
indicating failure a regular file is actually created. This doesn't make
a lot of sense.
Time was spent finding potential users of this combination. Searching on
codesearch.debian.net showed that codebases often express semantical
expectations about O_DIRECTORY | O_CREAT which are completely contrary
to what our code has done and currently does.
The expectation often is that this particular combination would create
and open a directory. This suggests users who tried to use that
combination would stumble upon the counterintuitive behavior no matter
if pre-v5.7 or post v5.7 and quickly realize neither semantics give them
what they want. For some examples see the code examples in [1] to [3]
and the discussion in [4].
There are various ways to address this issue. The lazy/simple option
would be to restore the pre-v5.7 behavior and to just live with that bug
forever. But since there's a real chance that the O_DIRECTORY | O_CREAT
quirk isn't relied upon we should try to get away with murder(ing bad
semantics) first. If we need to Frankenstein pre-v5.7 behavior later so
be it.
So let's simply return EINVAL categorically for O_DIRECTORY | O_CREAT
combinations. In addition to cleaning up the old bug this also opens up
the possiblity to make that flag combination do something more intuitive
in the future.
Starting with this commit the following semantics apply:
(1) open("/tmp/d", O_DIRECTORY | O_CREAT)
* d doesn't exist: EINVAL
* d exists and is a regular file: EINVAL
* d exists and is a directory: EINVAL
(2) open("/tmp/d", O_DIRECTORY | O_CREAT | O_EXCL)
* d doesn't exist: EINVAL
* d exists and is a regular file: EINVAL
* d exists and is a directory: EINVAL
(3) open("/tmp/d", O_DIRECTORY | O_EXCL)
* d doesn't exist: ENOENT
* d exists and is a regular file: ENOTDIR
* d exists and is a directory: open directory
One additional note, O_TMPFILE is implemented as:
#define __O_TMPFILE 020000000
#define O_TMPFILE (__O_TMPFILE | O_DIRECTORY)
#define O_TMPFILE_MASK (__O_TMPFILE | O_DIRECTORY | O_CREAT)
For older kernels it was important to return an explicit error when
O_TMPFILE wasn't supported. So O_TMPFILE requires that O_DIRECTORY is
raised alongside __O_TMPFILE. It also enforced that O_CREAT wasn't
specified. Since O_DIRECTORY | O_CREAT could be used to create a regular
allowing that combination together with __O_TMPFILE would've meant that
false positives were possible, i.e., that a regular file was created
instead of a O_TMPFILE. This could've been used to trick userspace into
thinking it operated on a O_TMPFILE when it wasn't.
Now that we block O_DIRECTORY | O_CREAT completely the check for O_CREAT
in the __O_TMPFILE branch via if ((flags & O_TMPFILE_MASK) != O_TMPFILE)
can be dropped. Instead we can simply check verify that O_DIRECTORY is
raised via if (!(flags & O_DIRECTORY)) and explain this in two comments.
As Aleksa pointed out O_PATH is unaffected by this change since it
always returned EINVAL if O_CREAT was specified - with or without
O_DIRECTORY.
Link: https://lore.kernel.org/lkml/20230320071442.172228-1-pedro.falcato@gmail.com
Link: https://sources.debian.org/src/flatpak/1.14.4-1/subprojects/libglnx/glnx-dirfd.c/?hl=324#L324 [1]
Link: https://sources.debian.org/src/flatpak-builder/1.2.3-1/subprojects/libglnx/glnx-shutil.c/?hl=251#L251 [2]
Link: https://sources.debian.org/src/ostree/2022.7-2/libglnx/glnx-dirfd.c/?hl=324#L324 [3]
Link: https://www.openwall.com/lists/oss-security/2014/11/26/14 [4]
Reported-by: Pedro Falcato <pedro.falcato@gmail.com>
Cc: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9949e2efb5 ]
Bonding send_peer_notif was defined as u8. Since commit 07a4ddec3c
("bonding: add an option to specify a delay between peer notifications").
the bond->send_peer_notif will be num_peer_notif multiplied by
peer_notif_delay, which is u8 * u32. This would cause the send_peer_notif
overflow easily. e.g.
ip link add bond0 type bond mode 1 miimon 100 num_grat_arp 30 peer_notify_delay 1000
To fix the overflow, let's set the send_peer_notif to u32 and limit
peer_notif_delay to 300s.
Reported-by: Liang Li <liali@redhat.com>
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2090053
Fixes: 07a4ddec3c ("bonding: add an option to specify a delay between peer notifications")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
