commit f58d0a9b4c upstream.
Packets bound for peers can queue up prior to the device private key
being set. For example, if persistent keepalive is set, a packet is
queued up to be sent as soon as the device comes up. However, if the
private key hasn't been set yet, the handshake message never sends, and
no timer is armed to retry, since that would be pointless.
But, if a user later sets a private key, the expectation is that those
queued packets, such as a persistent keepalive, are actually sent. So
adjust the configuration logic to account for this edge case, and add a
test case to make sure this works.
Maxim noticed this with a wg-quick(8) config to the tune of:
[Interface]
PostUp = wg set %i private-key somefile
[Peer]
PublicKey = ...
Endpoint = ...
PersistentKeepalive = 25
Here, the private key gets set after the device comes up using a PostUp
script, triggering the bug.
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Cc: stable@vger.kernel.org
Reported-by: Maxim Cournoyer <maxim.cournoyer@gmail.com>
Tested-by: Maxim Cournoyer <maxim.cournoyer@gmail.com>
Link: https://lore.kernel.org/wireguard/87fs7xtqrv.fsf@gmail.com/
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7387943fa3 upstream.
Using `% nr_cpumask_bits` is slow and complicated, and not totally
robust toward dynamic changes to CPU topologies. Rather than storing the
next CPU in the round-robin, just store the last one, and also return
that value. This simplifies the loop drastically into a much more common
pattern.
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Cc: stable@vger.kernel.org
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Manuel Leiner <manuel.leiner@gmx.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 525c469e5d upstream.
For some cases as below, we may encounter the unpreditable chip stats
in driver probe()
* The system reboot flow do not work properly, such as kernel oops while
rebooting, and then the driver do not go back to default status at
this moment.
* Similar to the flow above. If the device was enabled in BIOS or UEFI,
the system may switch to Linux without driver fully shutdown.
To avoid the problem, force push the device back to default in probe()
* mt7921e_mcu_fw_pmctrl() : return control privilege to chip side.
* mt7921_wfsys_reset() : cleanup chip config before resource init.
Error log
[59007.600714] mt7921e 0000:02:00.0: ASIC revision: 79220010
[59010.889773] mt7921e 0000:02:00.0: Message 00000010 (seq 1) timeout
[59010.889786] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59014.217839] mt7921e 0000:02:00.0: Message 00000010 (seq 2) timeout
[59014.217852] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59017.545880] mt7921e 0000:02:00.0: Message 00000010 (seq 3) timeout
[59017.545893] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59020.874086] mt7921e 0000:02:00.0: Message 00000010 (seq 4) timeout
[59020.874099] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59024.202019] mt7921e 0000:02:00.0: Message 00000010 (seq 5) timeout
[59024.202033] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59027.530082] mt7921e 0000:02:00.0: Message 00000010 (seq 6) timeout
[59027.530096] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59030.857888] mt7921e 0000:02:00.0: Message 00000010 (seq 7) timeout
[59030.857904] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59034.185946] mt7921e 0000:02:00.0: Message 00000010 (seq 8) timeout
[59034.185961] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59037.514249] mt7921e 0000:02:00.0: Message 00000010 (seq 9) timeout
[59037.514262] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59040.842362] mt7921e 0000:02:00.0: Message 00000010 (seq 10) timeout
[59040.842375] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59040.923845] mt7921e 0000:02:00.0: hardware init failed
Cc: stable@vger.kernel.org
Fixes: 5c14a5f944 ("mt76: mt7921: introduce mt7921e support")
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Juan Martinez <juan.martinez@amd.com>
Co-developed-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Message-ID: <39fcb7cee08d4ab940d38d82f21897483212483f.1688569385.git.deren.wu@mediatek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b719ebc37a upstream.
Serialize the ath10k implementation of the wake_tx_queue ops.
ath10k_mac_op_wake_tx_queue() must not run concurrent since it's using
ieee80211_txq_schedule_start().
The intend of this patch is to sort out an issue discovered in the discussion
referred to by the Link tag.
I can't test it with real hardware and thus just implemented the per-ac queue
lock Felix suggested. One obvious alternative to the per-ac lock would be to
bring back the txqs_lock commit bb2edb7335 ("ath10k: migrate to mac80211 txq
scheduling") dropped.
Fixes: bb2edb7335 ("ath10k: migrate to mac80211 txq scheduling")
Reported-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/519b5bb9-8899-ae7c-4eff-f3116cdfdb56@nbd.name
CC: <stable@vger.kernel.org>
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230323165527.156414-1-alexander@wetzel-home.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14bb236b29 ]
MAC block on CN10K (RPM) supports hardware timestamp configuration. The
previous patch which added timestamp configuration support has a bug.
Though the netdev driver requests to disable timestamp configuration,
the driver is always enabling it.
This patch fixes the same.
Fixes: d148920868 ("octeontx2-af: cn10k: RPM hardware timestamp configuration")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a372d66af4 ]
incl_srcpt has the limitation, mentioned in commit b4638af888 ("net:
dsa: sja1105: always enable the INCL_SRCPT option"), that frames with a
MAC DA of 01:80:c2:xx:yy:zz will be received as 01:80:c2:00:00:zz unless
PTP RX timestamping is enabled.
The incl_srcpt option was initially unconditionally enabled, then that
changed with commit 42824463d3 ("net: dsa: sja1105: Limit use of
incl_srcpt to bridge+vlan mode"), then again with b4638af888 ("net:
dsa: sja1105: always enable the INCL_SRCPT option"). Bottom line is that
it now needs to be always enabled, otherwise the driver does not have a
reliable source of information regarding source_port and switch_id for
link-local traffic (tag_8021q VLANs may be imprecise since now they
identify an entire bridging domain when ports are not standalone).
If we accept that PTP RX timestamping (and therefore, meta frame
generation) is always enabled in hardware, then that limitation could be
avoided and packets with any MAC DA can be properly received, because
meta frames do contain the original bytes from the MAC DA of their
associated link-local packet.
This change enables meta frame generation unconditionally, which also
has the nice side effects of simplifying the switch control path
(a switch reset is no longer required on hwtstamping settings change)
and the tagger data path (it no longer needs to be informed whether to
expect meta frames or not - it always does).
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84bef5b603 ]
PPTP uses pppox sockets (struct pppox_sock). These sockets don't embed
an inet_sock structure, so it's invalid to call inet_sk() on them.
Therefore, the ip_route_output_ports() call in pptp_connect() has two
problems:
* The tos variable is set with RT_CONN_FLAGS(sk), which calls
inet_sk() on the pppox socket.
* ip_route_output_ports() tries to retrieve routing flags using
inet_sk_flowi_flags(), which is also going to call inet_sk() on the
pppox socket.
While PPTP doesn't use inet sockets, it's actually really layered on
top of IP and therefore needs a proper way to do fib lookups. So let's
define pptp_route_output() to get a struct rtable from a pptp socket.
Let's also replace the ip_route_output_ports() call of pptp_xmit() for
consistency.
In practice, this means that:
* pptp_connect() sets ->flowi4_tos and ->flowi4_flags to zero instead
of using bits of unrelated struct pppox_sock fields.
* pptp_xmit() now respects ->sk_mark and ->sk_uid.
* pptp_xmit() now calls the security_sk_classify_flow() security
hook, thus allowing to set ->flowic_secid.
* pptp_xmit() now passes the pppox socket to xfrm_lookup_route().
Found by code inspection.
Fixes: 00959ade36 ("PPTP: PPP over IPv4 (Point-to-Point Tunneling Protocol)")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79ebb53772 ]
with the addition of new MAC blocks like CN10K RPM and CN10KB
RPM_USX, LMACs are noncontiguous and CGX blocks are also
noncontiguous. But during RVU driver initialization, the driver
is assuming they are contiguous and trying to access
cgx or lmac with their id which is resulting in kernel panic.
This patch fixes the issue by adding proper checks.
[ 23.219150] pc : cgx_lmac_read+0x38/0x70
[ 23.219154] lr : rvu_program_channels+0x3f0/0x498
[ 23.223852] sp : ffff000100d6fc80
[ 23.227158] x29: ffff000100d6fc80 x28: ffff00010009f880 x27:
000000000000005a
[ 23.234288] x26: ffff000102586768 x25: 0000000000002500 x24:
fffffffffff0f000
Fixes: 91c6945ea1 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e7bc57b97 ]
Firmware configures NIX block mapping for all MAC blocks.
The current implementation reads the configuration and
creates the mapping between RVU PF and NIX blocks. But
this configuration is only valid for silicons that support
multiple blocks. For all other silicons, all MAC blocks
map to NIX0.
This patch corrects the mapping by adding a check for the same.
Fixes: c5a73b632b ("octeontx2-af: Map NIX block from CGX connection")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08fc75735f ]
The line cards array is not freed in the error path of
mlxsw_m_linecards_init(), which can lead to a memory leak. Fix by
freeing the array in the error path, thereby making the error path
identical to mlxsw_m_linecards_fini().
Fixes: 01328e23a4 ("mlxsw: minimal: Extend module to port mapping with slot index")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230630012647.1078002-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cf62c8177 ]
Switch in MAXLEN register stores the maximum size of a data frame.
The MTU size is 18 bytes smaller than the frame size.
The current settings are causing problems with packet forwarding.
This patch fixes the MTU settings to proper values.
Fixes: fb77ffc6ec ("net: dsa: vsc73xx: make the MTU configurable")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230628194327.1765644-1-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48538ccb82 ]
All ibmvnic resets, make a call to netdev_tx_reset_queue() when
re-opening the device. netdev_tx_reset_queue() resets the num_queued
and num_completed byte counters. These stats are used in Byte Queue
Limit (BQL) algorithms. The difference between these two stats tracks
the number of bytes currently sitting on the physical NIC. ibmvnic
increases the number of queued bytes though calls to
netdev_tx_sent_queue() in the drivers xmit function. When, VIOS reports
that it is done transmitting bytes, the ibmvnic device increases the
number of completed bytes through calls to netdev_tx_completed_queue().
It is important to note that the driver batches its transmit calls and
num_queued is increased every time that an skb is added to the next
batch, not necessarily when the batch is sent to VIOS for transmission.
Unlike other reset types, a NON FATAL reset will not flush the sub crq
tx buffers. Therefore, it is possible for the batched skb array to be
partially full. So if there is call to netdev_tx_reset_queue() when
re-opening the device, the value of num_queued (0) would not account
for the skb's that are currently batched. Eventually, when the batch
is sent to VIOS, the call to netdev_tx_completed_queue() would increase
num_completed to a value greater than the num_queued. This causes a
BUG_ON crash:
ibmvnic 30000002: Firmware reports error, cause: adapter problem.
Starting recovery...
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
------------[ cut here ]------------
kernel BUG at lib/dynamic_queue_limits.c:27!
Oops: Exception in kernel mode, sig: 5
[....]
NIP dql_completed+0x28/0x1c0
LR ibmvnic_complete_tx.isra.0+0x23c/0x420 [ibmvnic]
Call Trace:
ibmvnic_complete_tx.isra.0+0x3f8/0x420 [ibmvnic] (unreliable)
ibmvnic_interrupt_tx+0x40/0x70 [ibmvnic]
__handle_irq_event_percpu+0x98/0x270
---[ end trace ]---
Therefore, do not reset the dql stats when performing a NON_FATAL reset.
Fixes: 0d97338818 ("ibmvnic: Introduce xmit_more support using batched subCRQ hcalls")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 046f753da6 ]
Fixes a bug where on the M1 mac mini initramfs-tools fails to
include the necessary firmware into the initrd.
Fixes: c4dab50697 ("tg3: Download 57766 EEE service patch firmware")
Signed-off-by: Tobias Heider <me@tobhe.de>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/ZJt7LKzjdz8+dClx@tobhe.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4638af888 ]
Link-local traffic on bridged SJA1105 ports is sometimes tagged by the
hardware with source port information (when the port is under a VLAN
aware bridge).
The tag_8021q source port identification has become more loose
("imprecise") and will report a plausible rather than exact bridge port,
when under a bridge (be it VLAN-aware or VLAN-unaware). But link-local
traffic always needs to know the precise source port.
Modify the driver logic (and therefore: the tagging protocol itself) to
always include the source port information with link-local packets,
regardless of whether the port is standalone, under a VLAN-aware or
VLAN-unaware bridge. This makes it possible for the tagging driver to
give priority to that information over the tag_8021q VLAN header.
The big drawback with INCL_SRCPT is that it makes it impossible to
distinguish between an original MAC DA of 01:80:C2:XX:YY:ZZ and
01:80:C2:AA:BB:ZZ, because the tagger just patches MAC DA bytes 3 and 4
with zeroes. Only if PTP RX timestamping is enabled, the switch will
generate a META follow-up frame containing the RX timestamp and the
original bytes 3 and 4 of the MAC DA. Those will be used to patch up the
original packet. Nonetheless, in the absence of PTP RX timestamping, we
have to live with this limitation, since it is more important to have
the more precise source port information for link-local traffic.
Fixes: d7f9787a76 ("net: dsa: tag_8021q: add support for imprecise RX based on the VBID")
Fixes: 91495f21fc ("net: dsa: tag_8021q: replace the SVL bridging with VLAN-unaware IVL bridging")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2edcfcbb3c ]
The driver implements a workaround for the fact that it doesn't have an
IRQ source to tell it whether PTP frames are available through the
extraction registers, for those frames to be processed and passed
towards the network stack. That workaround is to configure the switch,
through felix_hwtstamp_set() -> felix_update_trapping_destinations(),
to create two copies of PTP packets: one sent over Ethernet to the DSA
master, and one to be consumed through the aforementioned CPU extraction
queue registers.
The reason why we want PTP packets to be consumed through the CPU
extraction registers in the first place is because we want to see their
hardware RX timestamp. With tag_8021q, that is only visible that way,
and it isn't visible with the copy of the packet that's transmitted over
Ethernet.
The problem with the workaround implementation is that it drops the
packet received over Ethernet, in expectation of its copy being present
in the CPU extraction registers. However, if felix_hwtstamp_set() hasn't
run (aka PTP RX timestamping is disabled), the driver will drop the
original PTP frame and there will be no copy of it in the CPU extraction
registers. So, the network stack will simply not see any PTP frame.
Look at the port's trapping configuration to see whether the driver has
previously enabled the CPU extraction registers. If it hasn't, just
don't RX timestamp the frame and let it be passed up the stack by DSA,
which is perfectly fine.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45d0fcb5bc ]
In a future change, the driver will need to determine whether PTP RX
timestamping is enabled on a port (including whether traps were set up
on that port in particular) and that is currently not possible.
The driver supports different RX filters (L2, L4) and kinds of TX
timestamping (one-step, two-step) on its ports, but it saves all
configuration in a single struct hwtstamp_config that is global to the
switch. So, the latest timestamping configuration on one port
(including a request to disable timestamping) affects what gets reported
for all ports, even though the configuration itself is still individual
to each port.
The port timestamping configurations are only coupled because of the
common structure, so replace the hwtstamp_config with a mask of trapped
protocols saved per port. We also have the ptp_cmd to distinguish
between one-step and two-step PTP timestamping, so with those 2 bits of
information we can fully reconstruct a descriptive struct
hwtstamp_config for each port, during the SIOCGHWTSTAMP ioctl.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fd44b82b7 ]
PTP RX timestamping should be enabled when the user requests it, not by
default. If it is enabled by default, it can be problematic when the
ocelot driver is a DSA master, and it sidesteps what DSA tries to avoid
through __dsa_master_hwtstamp_validate().
Additionally, after the change which made ocelot trap PTP packets only
to the CPU at ocelot_hwtstamp_set() time, it is no longer even true that
RX timestamping is enabled by default, because until ocelot_hwtstamp_set()
is called, the PTP traps are actually not set up. So the rx_filter field
of ocelot->hwtstamp_config reflects an incorrect reality.
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a9922e7be ]
ipvlan_queue_xmit() should return NET_XMIT_XXX, but
ipvlan_xmit_mode_l2/l3() returns rx_handler_result_t or NET_RX_XXX
in some cases. ipvlan_rcv_frame() will only return RX_HANDLER_CONSUMED
in ipvlan_xmit_mode_l2/l3() because 'local' is true. It's equal to
NET_XMIT_SUCCESS. But dev_forward_skb() can return NET_RX_SUCCESS or
NET_RX_DROP, and returning NET_RX_DROP(NET_XMIT_DROP) will increase
both ipvlan and ipvlan->phy_dev drops counter.
The skb to forward can be treated as xmitted successfully. This patch
makes ipvlan_queue_xmit() return NET_XMIT_SUCCESS for forward skb.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230626093347.7492-1-cambda@linux.alibaba.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1b355438b ]
efx_net_stats() (.ndo_get_stats64) can be called during an ethtool
selftest, during which time nic_data->mc_stats is NULL as the NIC has
been fini'd. In this case do not attempt to fetch the latest stats
from the hardware, else we will crash on a NULL dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000038
RIP efx_nic_update_stats
abridged calltrace:
efx_ef10_update_stats_pf
efx_net_stats
dev_get_stats
dev_seq_printf_stats
Skipping the read is safe, we will simply give out stale stats.
To ensure that the free in efx_ef10_fini_nic() does not race against
efx_ef10_update_stats_pf(), which could cause a TOCTTOU bug, take the
efx->stats_lock in fini_nic (it is already held across update_stats).
Fixes: d3142c193d ("sfc: refactor EF10 stats handling")
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1bc9fc4a0 ]
64-bit DMA detection will fail if axienet was started before (by boot
loader, boot ROM, etc). In this state axienet will not start properly.
XAXIDMA_TX_CDESC_OFFSET + 4 register (MM2S_CURDESC_MSB) is used to detect
64-bit DMA capability here. But datasheet says: When DMACR.RS is 1
(axienet is in enabled state), CURDESC_PTR becomes Read Only (RO) and
is used to fetch the first descriptor. So iowrite32()/ioread32() trick
to this register to detect 64-bit DMA will not work.
So move axienet reset before 64-bit DMA detection.
Fixes: f735c40ed9 ("net: axienet: Autodetect 64-bit DMA capability")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20230622192245.116864-1-fido_max@inbox.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4fc88ad2a ]
Commit 49725ffc15 ("net: stmmac: power up/down serdes in
stmmac_open/release") correctly added a call to the serdes_powerdown()
callback to stmmac_release() but did not remove the one from
stmmac_remove() which leads to a doubled call to serdes_powerdown().
This can lead to all kinds of problems: in the case of the qcom ethqos
driver, it caused an unbalanced regulator disable splat.
Fixes: 49725ffc15 ("net: stmmac: power up/down serdes in stmmac_open/release")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Junxiao Chang <junxiao.chang@intel.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230621135537.376649-1-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2aa083acea ]
Since 'ieee80211_queue_delayed_work()' expects timeout in
jiffies and not milliseconds, 'msecs_to_jiffies()' should
be used in 'ath_restart_work()' and '__ath9k_flush()'.
Fixes: d63ffc45c5 ("ath9k: rename tx_complete_work to hw_check_work")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230613134655.248728-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2db72b8a70 ]
We've already done the 'decryption' here, so tell
mac80211 it need not do it again.
Fixes: b1fdc2505a ("iwlwifi: mvm: advertise BIGTK client support if available")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230620125813.a50cf68fbf2e.Ieceacbe3789d81ea02ae085ad8d1f8813a33c31b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1902f1953b ]
rxq can be NULL only when trans_pcie->rxq is NULL and entry->entry
is zero. For the case when entry->entry is not equal to 0, rxq
won't be NULL even if trans_pcie->rxq is NULL. Modify checker to
check for trans_pcie->rxq.
Fixes: abc599efa6 ("iwlwifi: pcie: don't crash when rx queues aren't allocated in interrupt")
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230614123446.5a5eb3889a4a.I375a1d58f16b48cd2044e7b7caddae512d7c86fd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96fb6f47db ]
In mac80211, it's required that we pull from TXQs by calling
ieee80211_tx_dequeue() only with softirqs disabled. However,
in iwl_mvm_queue_state_change() we're often called with them
enabled, e.g. from flush if anything was flushed, triggering
a mac80211 warning.
Fix that by disabling the softirqs across the TX call.
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230614123446.0feef7fa81db.I4dd62542d955b40dd8f0af34fa4accb9d0d17c7e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16e0077e14 ]
Add check for ioremap() and return the error if it fails in order to
guarantee the success of ioremap(), same as in
ath11k_qmi_load_file_target_mem().
Fixes: 6ac04bdc5e ("ath11k: Use reserved host DDR addresses from DT for PCI devices")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230608022858.27405-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75086cc6de ]
On EDMA capable hardware, ath9k_txq_list_has_key() can enter infinite
loop if it is called while all txq_fifos have packets that use different
key that the one we are looking for. Fix it by exiting the loop if all
txq_fifos have been checked already.
Because this loop is called under spin_lock_bh() (see ath_txq_lock) it
causes the following rcu stall:
rcu: INFO: rcu_sched self-detected stall on CPU
ath10k_pci 0000:01:00.0: failed to read temperature -11
rcu: 1-....: (5254 ticks this GP) idle=189/1/0x4000000000000002 softirq=8442983/8442984 fqs=2579
(t=5257 jiffies g=17983297 q=334)
Task dump for CPU 1:
task:hostapd state:R running task stack: 0 pid: 297 ppid: 289 flags:0x0000000a
Call trace:
dump_backtrace+0x0/0x170
show_stack+0x1c/0x24
sched_show_task+0x140/0x170
dump_cpu_task+0x48/0x54
rcu_dump_cpu_stacks+0xf0/0x134
rcu_sched_clock_irq+0x8d8/0x9fc
update_process_times+0xa0/0xec
tick_sched_timer+0x5c/0xd0
__hrtimer_run_queues+0x154/0x320
hrtimer_interrupt+0x120/0x2f0
arch_timer_handler_virt+0x38/0x44
handle_percpu_devid_irq+0x9c/0x1e0
handle_domain_irq+0x64/0x90
gic_handle_irq+0x78/0xb0
call_on_irq_stack+0x28/0x38
do_interrupt_handler+0x54/0x5c
el1_interrupt+0x2c/0x4c
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x74/0x78
ath9k_txq_has_key+0x1bc/0x250 [ath9k]
ath9k_set_key+0x1cc/0x3dc [ath9k]
drv_set_key+0x78/0x170
ieee80211_key_replace+0x564/0x6cc
ieee80211_key_link+0x174/0x220
ieee80211_add_key+0x11c/0x300
nl80211_new_key+0x12c/0x330
genl_family_rcv_msg_doit+0xbc/0x11c
genl_rcv_msg+0xd8/0x1c4
netlink_rcv_skb+0x40/0x100
genl_rcv+0x3c/0x50
netlink_unicast+0x1ec/0x2c0
netlink_sendmsg+0x198/0x3c0
____sys_sendmsg+0x210/0x250
___sys_sendmsg+0x78/0xc4
__sys_sendmsg+0x4c/0x90
__arm64_sys_sendmsg+0x28/0x30
invoke_syscall.constprop.0+0x60/0x100
do_el0_svc+0x48/0xd0
el0_svc+0x14/0x50
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x158/0x15c
This rcu stall is hard to reproduce as is, but changing ATH_TXFIFO_DEPTH
from 8 to 2 makes it reasonably easy to reproduce.
Fixes: ca2848022c ("ath9k: Postpone key cache entry deletion for TXQ frames reference it")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609093744.1985-1-repk@triplefau.lt
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e8b2c88fc ]
The ice_ptp_extts_work() and ice_ptp_periodic_work() functions are both
scheduled on the same kthread worker, pf.ptp.kworker. The
ice_ptp_periodic_work() function sends to the firmware to interact with the
PHY, and must block to wait for responses.
This can cause delay in responding to the PFINT_OICR_TSYN_EVNT interrupt
cause, ultimately resulting in disruption to processing an input signal of
the frequency is high enough. In our testing, even 100 Hz signals get
disrupted.
Fix this by instead processing the signal inside the miscellaneous
interrupt thread prior to handling Tx timestamps.
Use atomic bits in a new pf->misc_thread bitmap in order to safely
communicate which tasks require processing within the
ice_misc_intr_thread_fn(). This ensures the communication of desired tasks
from the ice_misc_intr() are correctly processed without racing even in the
event that the interrupt triggers again before the thread function exits.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e74f562328 ]
It makes no sense to set MMC_PM_KEEP_POWER in shutdown. The flag
indicates to the MMC subsystem to keep the slot powered on during
suspend, but in shutdown the slot should actually be powered off.
Drop this call.
Fixes: 063848c3e1 ("rsi: sdio: Add WOWLAN support for S5 shutdown state")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527222859.273768-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b241e26082 ]
In case WoWlan was never configured during the operation of the system,
the hw->wiphy->wowlan_config will be NULL. rsi_config_wowlan() checks
whether wowlan_config is non-NULL and if it is not, then WARNs about it.
The warning is valid, as during normal operation the rsi_config_wowlan()
should only ever be called with non-NULL wowlan_config. In shutdown this
rsi_config_wowlan() should only ever be called if WoWlan was configured
before by the user.
Add checks for non-NULL wowlan_config into the shutdown hook. While at it,
check whether the wiphy is also non-NULL before accessing wowlan_config .
Drop the single-use wowlan_config variable, just inline it into function
call.
Fixes: 16bbc3eb83 ("rsi: fix null pointer dereference during rsi_shutdown()")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527222833.273741-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75bd32f5ce ]
Currently, on WCN3990, the station disconnect after hardware recovery is
not working as expected. This is because of setting the
IEEE80211_SDATA_DISCONNECT_HW_RESTART flag very early in the hardware
recovery process even before the driver invokes ieee80211_hw_restart().
On the contrary, mac80211 expects this flag to be set after
ieee80211_hw_restart() is invoked for it to trigger station disconnect.
Set the IEEE80211_SDATA_DISCONNECT_HW_RESTART flag in
ath10k_reconfig_complete() instead to fix this.
The other targets are not affected by this change, since the hardware
params flag is not set.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1
Fixes: 2c3fc50591 ("ath10k: Trigger sta disconnect on hardware restart")
Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230518101515.3820-1-quic_youghand@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 061b0cb932 ]
A bad USB device is able to construct a service connection response
message with target endpoint being ENDPOINT0 which is reserved for
HTC_CTRL_RSVD_SVC and should not be modified to be used for any other
services.
Reject such service connection responses.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Reported-by: syzbot+b68fbebe56d8362907e8@syzkaller.appspotmail.com
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230516150427.79469-1-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f8d66a9fb ]
Should ray_config() fail, some resources need to be released as already
done in the remove function.
While at it, remove a useless and erroneous comment. The probe is
ray_probe(), not ray_attach().
Fixes: 15b99ac172 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/8c544d18084f8b37dd108e844f7e79e85ff708ff.1684570373.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 391af06a02 ]
Should wl3501_config() fail, some resources need to be released as already
done in the remove function.
Fixes: 15b99ac172 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7cc9c9316489b7d69b36aeb0edd3123538500b41.1684569865.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b92e4351a ]
Should atmel_config() fail, some resources need to be released as already
done in the remove function.
While at it, remove a useless and erroneous comment. The probe is
atmel_probe(), not atmel_attach().
Fixes: 15b99ac172 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1e65f174607a83348034197fa7d603bab10ba4a9.1684569156.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67a81d911c ]
Should orinoco_cs_config() fail, some resources need to be released as
already done in the remove function.
While at it, remove a useless and erroneous comment. The probe is
orinoco_cs_probe(), not orinoco_cs_attach().
Fixes: 15b99ac172 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/e24735ce4d82901d5f7ea08419eea53bfdde3d65.1684568286.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9252443251 ]
Should spectrum_cs_config() fail, some resources need to be released as
already done in the remove function.
While at it, remove a useless and erroneous comment. The probe is
spectrum_cs_probe(), not spectrum_cs_attach().
Fixes: 15b99ac172 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/c0bc0c21c58ca477fc5521607615bafbf2aef8eb.1684567733.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9aef04fcf ]
The type of "mwifiex_adapter->nd_info" is "struct cfg80211_wowlan_nd_info",
not "struct cfg80211_wowlan_nd_match".
Use struct_size() to ease the computation of the needed size.
The current code over-allocates some memory, so is safe.
But it wastes 32 bytes.
Fixes: 7d7f07d8c5 ("mwifiex: add wowlan net-detect support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7a6074fb056d2181e058a3cc6048d8155c20aec7.1683371982.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ce4bb0912 ]
Mandatory WFA testcase
CT_Security_WPA2Personal_STA_RSNEBoundsVerification-AbsentRSNCap,
performs bounds verfication on Beacon and/or Probe response frames. It
failed and observed the reason to be absence of cipher suite and AKM
suite in RSN information. To fix this, enable the RSN flag before extracting RSN
capabilities.
Fixes: cd21d99e59 ("wifi: wilc1000: validate pairwise and authentication suite offsets")
Signed-off-by: Amisha Patel <amisha.patel@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421181005.4865-1-amisha.patel@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24292e827 ]
For the reasons also described in commit b383e8abed ("wifi: ath9k: avoid
uninit memory read in ath9k_htc_rx_msg()"), ath9k_htc_rx_msg() should
validate pkt_len before accessing the SKB.
For example, the obtained SKB may have been badly constructed with
pkt_len = 8. In this case, the SKB can only contain a valid htc_frame_hdr
but after being processed in ath9k_htc_rx_msg() and passed to
ath9k_wmi_ctrl_rx() endpoint RX handler, it is expected to have a WMI
command header which should be located inside its data payload.
Implement sanity checking inside ath9k_wmi_ctrl_rx(). Otherwise, uninit
memory can be referenced.
Tested on Qualcomm Atheros Communications AR9271 802.11n .
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Reported-and-tested-by: syzbot+f2cb6e0ffdb961921e4d@syzkaller.appspotmail.com
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230424183348.111355-1-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e56c80931 ]
Fix ath9k_hw_verify_hang()/ar9003_hw_detect_mac_hang() register offset
calculation (do not overflow the shift for the second register/queues
above five, use the register layout described in the comments above
ath9k_hw_verify_hang() instead).
Fixes: 222e04830f ("ath9k: Fix MAC HW hang check for AR9003")
Reported-by: Gregg Wonderly <greggwonderly@seqtechllc.com>
Link: https://lore.kernel.org/linux-wireless/E3A9C354-0CB7-420C-ADEF-F0177FB722F4@seqtechllc.com/
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230422212423.26065-1-ps.report@gmx.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84214ab468 ]
When function igc_rx_hash() was introduced in v4.20 via commit 0507ef8a03
("igc: Add transmit and receive fastpath and interrupt handlers"), the
hardware wasn't configured to provide RSS hash, thus it made sense to not
enable net_device NETIF_F_RXHASH feature bit.
The NIC hardware was configured to enable RSS hash info in v5.2 via commit
2121c2712f ("igc: Add multiple receive queues control supporting"), but
forgot to set the NETIF_F_RXHASH feature bit.
The original implementation of igc_rx_hash() didn't extract the associated
pkt_hash_type, but statically set PKT_HASH_TYPE_L3. The largest portions of
this patch are about extracting the RSS Type from the hardware and mapping
this to enum pkt_hash_types. This was based on Foxville i225 software user
manual rev-1.3.1 and tested on Intel Ethernet Controller I225-LM (rev 03).
For UDP it's worth noting that RSS (type) hashing have been disabled both for
IPv4 and IPv6 (see IGC_MRQC_RSS_FIELD_IPV4_UDP + IGC_MRQC_RSS_FIELD_IPV6_UDP)
because hardware RSS doesn't handle fragmented pkts well when enabled (can
cause out-of-order). This results in PKT_HASH_TYPE_L3 for UDP packets, and
hash value doesn't include UDP port numbers. Not being PKT_HASH_TYPE_L4, have
the effect that netstack will do a software based hash calc calling into
flow_dissect, but only when code calls skb_get_hash(), which doesn't
necessary happen for local delivery.
For QA verification testing I wrote a small bpftrace prog:
[0] https://github.com/xdp-project/xdp-project/blob/master/areas/hints/monitor_skb_hash_on_dev.bt
Fixes: 2121c2712f ("igc: Add multiple receive queues control supporting")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/bpf/168182464270.616355.11391652654430626584.stgit@firesoul
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a129b41fe0 ]
This reverts commit da9ef50f54.
This fixes a regression in which the link would come up, but no
communication was possible.
The reverted commit was also removing a comment about
DP83867_PHYCR_FORCE_LINK_GOOD, this is not added back in this commits
since it seems that this is unrelated to the original code change.
Closes: https://lore.kernel.org/all/ZGuDJos8D7N0J6Z2@francesco-nb.int.toradex.com/
Fixes: da9ef50f54 ("net: phy: dp83867: perform soft reset and retain established link")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Link: https://lore.kernel.org/r/20230619154435.355485-1-francesco@dolcini.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7580e0a78e ]
We have seen a bug where the NIC incorrectly changes the length in the
IP header of a padded packet to include the padding bytes. The driver
already has a workaround for this so do the workaround for this NIC too.
This resolves the issue.
The NIC in question identifies itself as follows:
[ 8.828494] be2net 0000:02:00.0: FW version is 10.7.110.31
[ 8.834759] be2net 0000:02:00.0: Emulex OneConnect(be3): PF FLEX10 port 1
02:00.0 Ethernet controller: Emulex Corporation OneConnect 10Gb NIC (be3) (rev 01)
Fixes: ca34fe38f0 ("be2net: fix wrong usage of adapter->generation")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Link: https://lore.kernel.org/r/20230616164549.2863037-1-ross.lagerwall@citrix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8332cf6fd7 ]
LLDP frames are link-local frames, therefore they must be trapped to the
CPU port. Currently, the MT753X switches treat LLDP frames as regular
multicast frames, therefore flooding them to user ports. To fix this, set
LLDP frames to be trapped to the CPU port(s).
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7c6607355 ]
BPDUs are link-local frames, therefore they must be trapped to the CPU
port. Currently, the MT7530 switch treats BPDUs as regular multicast
frames, therefore flooding them to user ports. To fix this, set BPDUs to be
trapped to the CPU port. Group this on mt7530_setup() and
mt7531_setup_common() into mt753x_trap_frames() and call that.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
