[ Upstream commit 78adb4bcf9 ]
In normal operation, each populated queue item has
next_to_watch pointing to the last TX desc of the packet,
while each cleaned item has it set to 0. In particular,
next_to_use that points to the next (necessarily clean)
item to use has next_to_watch set to 0.
When the TX queue is used both by an application using
AF_XDP with ZEROCOPY as well as a second non-XDP application
generating high traffic, the queue pointers can get in
an invalid state where next_to_use points to an item
where next_to_watch is NOT set to 0.
However, the implementation assumes at several places
that this is never the case, so if it does hold,
bad things happen. In particular, within the loop inside
of igc_clean_tx_irq(), next_to_clean can overtake next_to_use.
Finally, this prevents any further transmission via
this queue and it never gets unblocked or signaled.
Secondly, if the queue is in this garbled state,
the inner loop of igc_clean_tx_ring() will never terminate,
completely hogging a CPU core.
The reason is that igc_xdp_xmit_zc() reads next_to_use
before acquiring the lock, and writing it back
(potentially unmodified) later. If it got modified
before locking, the outdated next_to_use is written
pointing to an item that was already used elsewhere
(and thus next_to_watch got written).
Fixes: 9acf59a752 ("igc: Enable TX via AF_XDP zero-copy")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230717175444.3217831-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95b6814855 ]
High XDP load triggers the netdev watchdog:
|NETDEV WATCHDOG: enp3s0 (igc): transmit queue 2 timed out
The reason is the Tx queue transmission start (txq->trans_start) is not updated
in XDP code path. Therefore, add it for all XDP transmission functions.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 78adb4bcf9 ("igc: Prevent garbled TX queue with XDP ZEROCOPY")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fcd7c7b3a ]
Current driver enables backpressure for LBK interfaces.
But these interfaces do not support this feature.
Hence, this patch fixes the issue by skipping the
backpressure configuration for these interfaces.
Fixes: 75f3627099 ("octeontx2-pf: Support to enable/disable pause frames via ethtool").
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20230716093741.28063-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c34743daca ]
The reset task is currently scheduled from the watchdog or adminq tasks.
First, all direct calls to schedule the reset task are replaced with the
iavf_schedule_reset(), which is modified to accept the flag showing the
type of reset.
To prevent the reset task from starting once iavf_remove() starts, we need
to check the __IAVF_IN_REMOVE_TASK bit before we schedule it. This is now
easily added to iavf_schedule_reset().
Finally, remove the check for IAVF_FLAG_RESET_NEEDED in the watchdog task.
It is redundant since all callers who set the flag immediately schedules
the reset task.
Fixes: 3ccd54ef44 ("iavf: Fix init state closure on remove")
Fixes: 14756b2ae2 ("iavf: Fix __IAVF_RESETTING state usage")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1639a1731 ]
A driver's lock (crit_lock) is used to serialize all the driver's tasks.
Lockdep, however, shows a circular dependency between rtnl and
crit_lock. This happens when an ndo that already holds the rtnl requests
the driver to reset, since the reset task (in some paths) tries to grab
rtnl to either change real number of queues of update netdev features.
[566.241851] ======================================================
[566.241893] WARNING: possible circular locking dependency detected
[566.241936] 6.2.14-100.fc36.x86_64+debug #1 Tainted: G OE
[566.241984] ------------------------------------------------------
[566.242025] repro.sh/2604 is trying to acquire lock:
[566.242061] ffff9280fc5ceee8 (&adapter->crit_lock){+.+.}-{3:3}, at: iavf_close+0x3c/0x240 [iavf]
[566.242167]
but task is already holding lock:
[566.242209] ffffffff9976d350 (rtnl_mutex){+.+.}-{3:3}, at: iavf_remove+0x6b5/0x730 [iavf]
[566.242300]
which lock already depends on the new lock.
[566.242353]
the existing dependency chain (in reverse order) is:
[566.242401]
-> #1 (rtnl_mutex){+.+.}-{3:3}:
[566.242451] __mutex_lock+0xc1/0xbb0
[566.242489] iavf_init_interrupt_scheme+0x179/0x440 [iavf]
[566.242560] iavf_watchdog_task+0x80b/0x1400 [iavf]
[566.242627] process_one_work+0x2b3/0x560
[566.242663] worker_thread+0x4f/0x3a0
[566.242696] kthread+0xf2/0x120
[566.242730] ret_from_fork+0x29/0x50
[566.242763]
-> #0 (&adapter->crit_lock){+.+.}-{3:3}:
[566.242815] __lock_acquire+0x15ff/0x22b0
[566.242869] lock_acquire+0xd2/0x2c0
[566.242901] __mutex_lock+0xc1/0xbb0
[566.242934] iavf_close+0x3c/0x240 [iavf]
[566.242997] __dev_close_many+0xac/0x120
[566.243036] dev_close_many+0x8b/0x140
[566.243071] unregister_netdevice_many_notify+0x165/0x7c0
[566.243116] unregister_netdevice_queue+0xd3/0x110
[566.243157] iavf_remove+0x6c1/0x730 [iavf]
[566.243217] pci_device_remove+0x33/0xa0
[566.243257] device_release_driver_internal+0x1bc/0x240
[566.243299] pci_stop_bus_device+0x6c/0x90
[566.243338] pci_stop_and_remove_bus_device+0xe/0x20
[566.243380] pci_iov_remove_virtfn+0xd1/0x130
[566.243417] sriov_disable+0x34/0xe0
[566.243448] ice_free_vfs+0x2da/0x330 [ice]
[566.244383] ice_sriov_configure+0x88/0xad0 [ice]
[566.245353] sriov_numvfs_store+0xde/0x1d0
[566.246156] kernfs_fop_write_iter+0x15e/0x210
[566.246921] vfs_write+0x288/0x530
[566.247671] ksys_write+0x74/0xf0
[566.248408] do_syscall_64+0x58/0x80
[566.249145] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[566.249886]
other info that might help us debug this:
[566.252014] Possible unsafe locking scenario:
[566.253432] CPU0 CPU1
[566.254118] ---- ----
[566.254800] lock(rtnl_mutex);
[566.255514] lock(&adapter->crit_lock);
[566.256233] lock(rtnl_mutex);
[566.256897] lock(&adapter->crit_lock);
[566.257388]
*** DEADLOCK ***
The deadlock can be triggered by a script that is continuously resetting
the VF adapter while doing other operations requiring RTNL, e.g:
while :; do
ip link set $VF up
ethtool --set-channels $VF combined 2
ip link set $VF down
ip link set $VF up
ethtool --set-channels $VF combined 4
ip link set $VF down
done
Any operation that triggers a reset can substitute "ethtool --set-channles"
As a fix, add a new task "finish_config" that do all the work which
needs rtnl lock. With the exception of iavf_remove(), all work that
require rtnl should be called from this task.
As for iavf_remove(), at the point where we need to call
unregister_netdevice() (and grab rtnl_lock), we make sure the finish_config
task is not running (cancel_work_sync()) to safely grab rtnl. Subsequent
finish_config work cannot restart after that since the task is guarded
by the __IAVF_IN_REMOVE_TASK bit in iavf_schedule_finish_config().
Fixes: 5ac49f3c27 ("iavf: use mutexes for locking of critical sections")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2ed2403f1 ]
There was a fail when trying to add the interface to bonding
right after changing the MTU on the interface. It was caused
by bonding interface unable to open the interface due to
interface being in __RESETTING state because of MTU change.
Add new reset_waitqueue to indicate that reset has finished.
Add waiting for reset to finish in callbacks which trigger hw reset:
iavf_set_priv_flags(), iavf_change_mtu() and iavf_set_ringparam().
We use a 5000ms timeout period because on Hyper-V based systems,
this operation takes around 3000-4000ms. In normal circumstances,
it doesn't take more than 500ms to complete.
Add a function iavf_wait_for_reset() to reuse waiting for reset code and
use it also in iavf_set_channels(), which already waits for reset.
We don't use error handling in iavf_set_channels() as this could
cause the device to be in incorrect state if the reset was scheduled
but hit timeout or the waitng function was interrupted by a signal.
Fixes: 4e5e6b5d9d ("iavf: Fix return of set the new channel count")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Co-developed-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4aadf0f59 ]
Make all possible functions static.
Move iavf_force_wb() up to avoid forward declaration.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: c2ed2403f1 ("iavf: Wait for reset in callbacks which trigger it")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dcbdf2928 ]
When the user disables rxvlan offloading and then changes the number of
channels, all VLAN ports are unable to receive traffic.
Changing the number of channels triggers a VFR reset. During re-init, when
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is received, we do:
1 - set the IAVF_FLAG_SETUP_NETDEV_FEATURES flag
2 - call
iavf_set_vlan_offload_features(adapter, 0, netdev->features);
The second step sends to the PF the __default__ features, in this case
aq_required |= IAVF_FLAG_AQ_ENABLE_CTAG_VLAN_STRIPPING
While the first step forces the watchdog task to call
netdev_update_features() -> iavf_set_features() ->
iavf_set_vlan_offload_features(adapter, netdev->features, features).
Since the user disabled the "rxvlan", this sets:
aq_required |= IAVF_FLAG_AQ_DISABLE_CTAG_VLAN_STRIPPING
When we start processing the AQ commands, both flags are enabled. Since we
process DISABLE_XTAG first then ENABLE_XTAG, this results in the PF
enabling the rxvlan offload. This breaks all communications on the VLAN
net devices.
Fix by removing the call to iavf_set_vlan_offload_features() (second
step). Calling netdev_update_features() from watchdog task is enough for
both init and reset paths.
Fixes: 7598f4b40b ("iavf: Move netdev_update_features() into watchdog task")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: c2ed2403f1 ("iavf: Wait for reset in callbacks which trigger it")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7598f4b40b ]
Remove netdev_update_features() from iavf_adminq_task(), as it can cause
deadlocks due to needing rtnl_lock. Instead use the
IAVF_FLAG_SETUP_NETDEV_FEATURES flag to indicate that netdev features need
to be updated in the watchdog task. iavf_set_vlan_offload_features()
and iavf_set_queue_vlan_tag_loc() can be called directly from
iavf_virtchnl_completion().
Suggested-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: c2ed2403f1 ("iavf: Wait for reset in callbacks which trigger it")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a77ed5c5b7 ]
If the system tries to close the netdev while iavf_reset_task() is
running, __LINK_STATE_START will be cleared and netif_running() will
return false in iavf_reinit_interrupt_scheme(). This will result in
iavf_free_traffic_irqs() not being called and a leak as follows:
[7632.489326] remove_proc_entry: removing non-empty directory 'irq/999', leaking at least 'iavf-enp24s0f0v0-TxRx-0'
[7632.490214] WARNING: CPU: 0 PID: 10 at fs/proc/generic.c:718 remove_proc_entry+0x19b/0x1b0
is shown when pci_disable_msix() is later called. Fix by using the
internal adapter state. The traffic IRQs will always exist if
state == __IAVF_RUNNING.
Fixes: 5b36e8d04b ("i40evf: Enable VF to request an alternate queue allocation")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d6d537dc5 ]
Move the call to of_get_ethdev_address to mtk_add_mac which is part of
the probe function and can hence itself return -EPROBE_DEFER should
of_get_ethdev_address return -EPROBE_DEFER. This allows us to entirely
get rid of the mtk_init function.
The problem of of_get_ethdev_address returning -EPROBE_DEFER surfaced
in situations in which the NVMEM provider holding the MAC address has
not yet be loaded at the time mtk_eth_soc is initially probed. In this
case probing of mtk_eth_soc should be deferred instead of falling back
to use a random MAC address, so once the NVMEM provider becomes
available probing can be repeated.
Fixes: 656e705243 ("net-next: mediatek: add support for MT7623 ethernet")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b685f1a589 ]
CPSW ALE has 75 bit ALE entries which are stored within three 32 bit words.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions assume that the
field will be strictly contained within one word. However, this is not
guaranteed to be the case and it is possible for ALE field entries to span
across up to two words at the most.
Fix the methods to handle getting/setting fields spanning up to two words.
Fixes: db82173f23 ("netdev: driver: ethernet: add cpsw address lookup engine support")
Signed-off-by: Tanmay Patil <t-patil@ti.com>
[s-vadapalli@ti.com: rephrased commit message and added Fixes tag]
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cf3d5567f ]
Now, strncpy() in hns3_dbg_fill_content() use src-length as copy-length,
it may result in dest-buf overflow.
This patch is to fix intel compile warning for csky-linux-gcc (GCC) 12.1.0
compiler.
The warning reports as below:
hclge_debugfs.c:92:25: warning: 'strncpy' specified bound depends on
the length of the source argument [-Wstringop-truncation]
strncpy(pos, items[i].name, strlen(items[i].name));
hclge_debugfs.c:90:25: warning: 'strncpy' output truncated before
terminating nul copying as many bytes from a string as its length
[-Wstringop-truncation]
strncpy(pos, result[i], strlen(result[i]));
strncpy() use src-length as copy-length, it may result in
dest-buf overflow.
So,this patch add some values check to avoid this issue.
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/lkml/202207170606.7WtHs9yS-lkp@intel.com/T/
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 004d25060c ]
In a setup where a Thunderbolt hub connects to Ethernet and a display
through USB Type-C, users may experience a hung task timeout when they
remove the cable between the PC and the Thunderbolt hub.
This is because the igb_down function is called multiple times when
the Thunderbolt hub is unplugged. For example, the igb_io_error_detected
triggers the first call, and the igb_remove triggers the second call.
The second call to igb_down will block at napi_synchronize.
Here's the call trace:
__schedule+0x3b0/0xddb
? __mod_timer+0x164/0x5d3
schedule+0x44/0xa8
schedule_timeout+0xb2/0x2a4
? run_local_timers+0x4e/0x4e
msleep+0x31/0x38
igb_down+0x12c/0x22a [igb 6615058754948bfde0bf01429257eb59f13030d4]
__igb_close+0x6f/0x9c [igb 6615058754948bfde0bf01429257eb59f13030d4]
igb_close+0x23/0x2b [igb 6615058754948bfde0bf01429257eb59f13030d4]
__dev_close_many+0x95/0xec
dev_close_many+0x6e/0x103
unregister_netdevice_many+0x105/0x5b1
unregister_netdevice_queue+0xc2/0x10d
unregister_netdev+0x1c/0x23
igb_remove+0xa7/0x11c [igb 6615058754948bfde0bf01429257eb59f13030d4]
pci_device_remove+0x3f/0x9c
device_release_driver_internal+0xfe/0x1b4
pci_stop_bus_device+0x5b/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_and_remove_bus_device+0x12/0x19
pciehp_unconfigure_device+0x76/0xe9
pciehp_disable_slot+0x6e/0x131
pciehp_handle_presence_or_link_change+0x7a/0x3f7
pciehp_ist+0xbe/0x194
irq_thread_fn+0x22/0x4d
? irq_thread+0x1fd/0x1fd
irq_thread+0x17b/0x1fd
? irq_forced_thread_fn+0x5f/0x5f
kthread+0x142/0x153
? __irq_get_irqchip_state+0x46/0x46
? kthread_associate_blkcg+0x71/0x71
ret_from_fork+0x1f/0x30
In this case, igb_io_error_detected detaches the network interface
and requests a PCIE slot reset, however, the PCIE reset callback is
not being invoked and thus the Ethernet connection breaks down.
As the PCIE error in this case is a non-fatal one, requesting a
slot reset can be avoided.
This patch fixes the task hung issue and preserves Ethernet
connection by ignoring non-fatal PCIE errors.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230620174732.4145155-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18da174d86 ]
Implement 64 bit per cpu stats to fix the overflow of netdev->stats
on 32 bit platforms. To simplify the code, we use net core
pcpu_sw_netstats infrastructure. One small drawback is some memory
overhead because litex uses just one queue, but we allocate the
counters per cpu.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20230614162035.300-1-jszhang@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e9cb763e9 upstream.
The ENA adapters on our instances occasionally reset. Once recently
logged a UBSAN failure to console in the process:
UBSAN: shift-out-of-bounds in build/linux/drivers/net/ethernet/amazon/ena/ena_com.c:540:13
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 28 PID: 70012 Comm: kworker/u72:2 Kdump: loaded not tainted 5.15.117
Hardware name: Amazon EC2 c5d.9xlarge/, BIOS 1.0 10/16/2017
Workqueue: ena ena_fw_reset_device [ena]
Call Trace:
<TASK>
dump_stack_lvl+0x4a/0x63
dump_stack+0x10/0x16
ubsan_epilogue+0x9/0x36
__ubsan_handle_shift_out_of_bounds.cold+0x61/0x10e
? __const_udelay+0x43/0x50
ena_delay_exponential_backoff_us.cold+0x16/0x1e [ena]
wait_for_reset_state+0x54/0xa0 [ena]
ena_com_dev_reset+0xc8/0x110 [ena]
ena_down+0x3fe/0x480 [ena]
ena_destroy_device+0xeb/0xf0 [ena]
ena_fw_reset_device+0x30/0x50 [ena]
process_one_work+0x22b/0x3d0
worker_thread+0x4d/0x3f0
? process_one_work+0x3d0/0x3d0
kthread+0x12a/0x150
? set_kthread_struct+0x50/0x50
ret_from_fork+0x22/0x30
</TASK>
Apparently, the reset delays are getting so large they can trigger a
UBSAN panic.
Looking at the code, the current timeout is capped at 5000us. Using a
base value of 100us, the current code will overflow after (1<<29). Even
at values before 32, this function wraps around, perhaps
unintentionally.
Cap the value of the exponent used for this backoff at (1<<16) which is
larger than currently necessary, but large enough to support bigger
values in the future.
Cc: stable@vger.kernel.org
Fixes: 4bb7f4cf60 ("net: ena: reduce driver load time")
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/r/20230711013621.GE1926@templeofstupid.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b5ea7ffb7 upstream.
With support for Ethernet PHY LEDs having been added, while
unregistering a MDIO bus and its child device liks PHYs there may be
"late" accesses to the MDIO bus. One typical use case is setting the PHY
LEDs brightness to OFF for instance.
We need to ensure that the MDIO bus controller remains entirely
functional since it runs off the main GENET adapter clock.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20230617155500.4005881-1-andrew@lunn.ch/
Fixes: 9a4e796970 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230622103107.1760280-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8278ee2a26 ]
Due to hardware limitation, MCAM drop rule with
ether_type == 802.1Q and vlan_id == 0 is not supported. Hence rejecting
such rules.
Fixes: dce677da57 ("octeontx2-pf: Add vlan-etype to ntuple filters")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20230710103027.2244139-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bcc62858d ]
The insertion of an empty frame was introduced with
commit db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
in order to ensure that the current cycle has at least one packet if
there is some packet to be scheduled for the next cycle.
However, the current implementation does not properly check if
a packet is already scheduled for the current cycle. Currently,
an empty packet is always inserted if and only if
txtime >= end_of_cycle && txtime > last_tx_cycle
but since last_tx_cycle is always either the end of the current
cycle (end_of_cycle) or the end of a previous cycle, the
second part (txtime > last_tx_cycle) is always true unless
txtime == last_tx_cycle.
What actually needs to be checked here is if the last_tx_cycle
was already written within the current cycle, so an empty frame
should only be inserted if and only if
txtime >= end_of_cycle && end_of_cycle > last_tx_cycle.
This patch does not only avoid an unnecessary insertion, but it
can actually be harmful to insert an empty packet if packets
are already scheduled in the current cycle, because it can lead
to a situation where the empty packet is actually processed
as the first packet in the upcoming cycle shifting the packet
with the first_flag even one cycle into the future, finally leading
to a TX hang.
The TX hang can be reproduced on a i225 with:
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <32>
TDT <3c>
next_to_use <3c>
next_to_clean <32>
buffer_info[next_to_clean]
time_stamp <ffff26a8>
next_to_watch <00000000632a1828>
jiffies <ffff27f8>
desc.status <1048000>
Fixes: db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1bca9ac0b ]
It is possible (verified on a running system) that frames are processed
by igc_tx_launchtime with a txtime before the start of the cycle
(baset_est).
However, the result of txtime - baset_est is written into a u32,
leading to a wrap around to a positive number. The following
launchtime > 0 check will only branch to executing launchtime = 0
if launchtime is already 0.
Fix it by using a s32 before checking launchtime > 0.
Fixes: db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7731194fd ]
Turning IRQs off is done by accessing Ethernet controller registers.
That can't be done until device's clock is enabled. It results in a SoC
hang otherwise.
This bug remained unnoticed for years as most bootloaders keep all
Ethernet interfaces turned on. It seems to only affect a niche SoC
family BCM47189. It has two Ethernet controllers but CFE bootloader uses
only the first one.
Fixes: 34322615cb ("net: bgmac: Mask interrupts during probe")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abfb2a58a5 ]
Remove unnecessary early code development check and the WARN_ON
that it uses. The irq alloc and free paths have long been
cleaned up and this check shouldn't have stuck around so long.
Fixes: 77ceb68e29 ("ionic: Add notifyq support")
Signed-off-by: Nitya Sunkad <nitya.sunkad@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7709fbd492 ]
Moved PTP pointer validation before its use to avoid smatch warning.
Also used kzalloc/kfree instead of devm_kzalloc/devm_kfree.
Fixes: 2ef4e45d99 ("octeontx2-af: Add PTP PPS Errata workaround on CN10K silicon")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af42088bda ]
In legacy silicon, promiscuous mode is only modified
through CGX mbox messages. In CN10KB silicon, it is modified
from CGX mbox and NIX. This breaks legacy application
behaviour. Fix this by removing call from NIX.
Fixes: d6c9784baf ("octeontx2-af: Invoke exact match functions if supported")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0503efeadb ]
Current duplex mode was unset in the driver, resulting in the default
parameter being set to 0, which corresponds to half duplex. It might
mislead users to have incorrect expectation about the driver's
transmission capabilities.
Set the default duplex configuration to full, as the driver runs in
full duplex mode at this point.
Fixes: 7e074d5a76 ("gve: Enable Link Speed Reporting in the driver.")
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Message-ID: <20230706044128.2726747-1-junfeng.guo@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21327f81db ]
If we boot with mvneta.txq_number=1, the txq_map is set incorrectly:
MVNETA_CPU_TXQ_ACCESS(1) refers to TX queue 1, but only TX queue 0 is
initialized. Fix this.
Fixes: 50bf8cb6fc ("net: mvneta: Configure XPS support")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/20230705053712.3914-1-klaus.kudielka@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84a192e461 ]
I225/6 hardware can be programmed to start PPS output once
the time in Target Time registers is reached. The time
programmed in these registers should always be into future.
Only then PPS output is triggered when SYSTIM register
reaches the programmed value. There are two modes in i225/6
hardware to program PPS, pulse and clock mode.
There were issues reported where PPS is not generated when
start time is in past.
Example 1, "echo 0 0 0 2 0 > /sys/class/ptp/ptp0/period"
In the current implementation, a value of '0' is programmed
into Target time registers and PPS output is in pulse mode.
Eventually an interrupt which is triggered upon SYSTIM
register reaching Target time is not fired. Thus no PPS
output is generated.
Example 2, "echo 0 0 0 1 0 > /sys/class/ptp/ptp0/period"
Above case, a value of '0' is programmed into Target time
registers and PPS output is in clock mode. Here, HW tries to
catch-up the current time by incrementing Target Time
register. This catch-up time seem to vary according to
programmed PPS period time as per the HW design. In my
experiments, the delay ranged between few tens of seconds to
few minutes. The PPS output is only generated after the
Target time register reaches current time.
In my experiments, I also observed PPS stopped working with
below test and could not recover until module is removed and
loaded again.
1) echo 0 <future time> 0 1 0 > /sys/class/ptp/ptp1/period
2) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period
3) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period
After this PPS did not work even if i re-program with proper
values. I could only get this back working by reloading the
driver.
This patch takes care of calculating and programming
appropriate future time value into Target Time registers.
Fixes: 5e91c72e56 ("igc: Fix PPS delta between two synchronized end-points")
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ac3fc2f42 ]
set TP bit in the 'supported' and 'advertising' fields. i225/226 parts
only support twisted pair copper.
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Signed-off-by: Prasad Koya <prasad@arista.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d543b649ff ]
When kvzalloc_node or kvzalloc failed in mlx5e_ptp_open, the memory
pointed by "c" or "cparams" is not freed, which can lead to a memory
leak. Fix by freeing the array in the error path.
Fixes: 145e5637d9 ("net/mlx5e: Add TX PTP port object support")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3250affdc6 ]
The memory pointed to by the fs->any pointer is not freed in the error
path of mlx5e_fs_tt_redirect_any_create, which can lead to a memory leak.
Fix by freeing the memory in the error path, thereby making the error path
identical to mlx5e_fs_tt_redirect_any_destroy().
Fixes: 0f575c20bf ("net/mlx5e: Introduce Flow Steering ANY API")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884abe45a9 ]
In function accel_fs_tcp_create_groups(), when the ft->g memory is
successfully allocated but the 'in' memory fails to be allocated, the
memory pointed to by ft->g is released once. And in function
accel_fs_tcp_create_table, mlx5e_destroy_flow_table is called to release
the memory pointed to by ft->g again. This will cause double free problem.
Fixes: c062d52ac2 ("net/mlx5e: Receive flow steering framework for accelerated TCP flows")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cca28ceac7 ]
Remove unnecessary delay during the TX ring configuration.
This will cause delay, especially during link down and
link up activity.
Furthermore, old SKUs like as I225 will call the reset_adapter
to reset the controller during TSN mode Gate Control List (GCL)
setting. This will add more time to the configuration of the
real-time use case.
It doesn't mentioned about this delay in the Software User Manual.
It might have been ported from legacy code I210 in the past.
Fixes: 13b5b7fd6a ("igc: Add support for Tx/Rx rings")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f16da6ee6 ]
Remove incorrect check in ice_validate_mqprio_opt() that limits
filter configuration when sum of max_rates of all TCs exceeds
the link speed. The max rate of each TC is unrelated to value
used by other TCs and is valid as long as it is less than link
speed.
Fixes: fbc7b27af0 ("ice: enable ndo_setup_tc support for mqprio_qdisc")
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7a8227b2e7 upstream.
dev_set_rx_mode() grabs a spin_lock, and the lan743x implementation
proceeds subsequently to go to sleep using readx_poll_timeout().
Introduce a helper wrapping the readx_poll_timeout_atomic() function
and use it to replace the calls to readx_polL_timeout().
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Cc: stable@vger.kernel.org
Cc: Bryan Whitehead <bryan.whitehead@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230627035000.1295254-1-moritzf@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14bb236b29 ]
MAC block on CN10K (RPM) supports hardware timestamp configuration. The
previous patch which added timestamp configuration support has a bug.
Though the netdev driver requests to disable timestamp configuration,
the driver is always enabling it.
This patch fixes the same.
Fixes: d148920868 ("octeontx2-af: cn10k: RPM hardware timestamp configuration")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79ebb53772 ]
with the addition of new MAC blocks like CN10K RPM and CN10KB
RPM_USX, LMACs are noncontiguous and CGX blocks are also
noncontiguous. But during RVU driver initialization, the driver
is assuming they are contiguous and trying to access
cgx or lmac with their id which is resulting in kernel panic.
This patch fixes the issue by adding proper checks.
[ 23.219150] pc : cgx_lmac_read+0x38/0x70
[ 23.219154] lr : rvu_program_channels+0x3f0/0x498
[ 23.223852] sp : ffff000100d6fc80
[ 23.227158] x29: ffff000100d6fc80 x28: ffff00010009f880 x27:
000000000000005a
[ 23.234288] x26: ffff000102586768 x25: 0000000000002500 x24:
fffffffffff0f000
Fixes: 91c6945ea1 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e7bc57b97 ]
Firmware configures NIX block mapping for all MAC blocks.
The current implementation reads the configuration and
creates the mapping between RVU PF and NIX blocks. But
this configuration is only valid for silicons that support
multiple blocks. For all other silicons, all MAC blocks
map to NIX0.
This patch corrects the mapping by adding a check for the same.
Fixes: c5a73b632b ("octeontx2-af: Map NIX block from CGX connection")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08fc75735f ]
The line cards array is not freed in the error path of
mlxsw_m_linecards_init(), which can lead to a memory leak. Fix by
freeing the array in the error path, thereby making the error path
identical to mlxsw_m_linecards_fini().
Fixes: 01328e23a4 ("mlxsw: minimal: Extend module to port mapping with slot index")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230630012647.1078002-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48538ccb82 ]
All ibmvnic resets, make a call to netdev_tx_reset_queue() when
re-opening the device. netdev_tx_reset_queue() resets the num_queued
and num_completed byte counters. These stats are used in Byte Queue
Limit (BQL) algorithms. The difference between these two stats tracks
the number of bytes currently sitting on the physical NIC. ibmvnic
increases the number of queued bytes though calls to
netdev_tx_sent_queue() in the drivers xmit function. When, VIOS reports
that it is done transmitting bytes, the ibmvnic device increases the
number of completed bytes through calls to netdev_tx_completed_queue().
It is important to note that the driver batches its transmit calls and
num_queued is increased every time that an skb is added to the next
batch, not necessarily when the batch is sent to VIOS for transmission.
Unlike other reset types, a NON FATAL reset will not flush the sub crq
tx buffers. Therefore, it is possible for the batched skb array to be
partially full. So if there is call to netdev_tx_reset_queue() when
re-opening the device, the value of num_queued (0) would not account
for the skb's that are currently batched. Eventually, when the batch
is sent to VIOS, the call to netdev_tx_completed_queue() would increase
num_completed to a value greater than the num_queued. This causes a
BUG_ON crash:
ibmvnic 30000002: Firmware reports error, cause: adapter problem.
Starting recovery...
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
------------[ cut here ]------------
kernel BUG at lib/dynamic_queue_limits.c:27!
Oops: Exception in kernel mode, sig: 5
[....]
NIP dql_completed+0x28/0x1c0
LR ibmvnic_complete_tx.isra.0+0x23c/0x420 [ibmvnic]
Call Trace:
ibmvnic_complete_tx.isra.0+0x3f8/0x420 [ibmvnic] (unreliable)
ibmvnic_interrupt_tx+0x40/0x70 [ibmvnic]
__handle_irq_event_percpu+0x98/0x270
---[ end trace ]---
Therefore, do not reset the dql stats when performing a NON_FATAL reset.
Fixes: 0d97338818 ("ibmvnic: Introduce xmit_more support using batched subCRQ hcalls")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 046f753da6 ]
Fixes a bug where on the M1 mac mini initramfs-tools fails to
include the necessary firmware into the initrd.
Fixes: c4dab50697 ("tg3: Download 57766 EEE service patch firmware")
Signed-off-by: Tobias Heider <me@tobhe.de>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/ZJt7LKzjdz8+dClx@tobhe.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45d0fcb5bc ]
In a future change, the driver will need to determine whether PTP RX
timestamping is enabled on a port (including whether traps were set up
on that port in particular) and that is currently not possible.
The driver supports different RX filters (L2, L4) and kinds of TX
timestamping (one-step, two-step) on its ports, but it saves all
configuration in a single struct hwtstamp_config that is global to the
switch. So, the latest timestamping configuration on one port
(including a request to disable timestamping) affects what gets reported
for all ports, even though the configuration itself is still individual
to each port.
The port timestamping configurations are only coupled because of the
common structure, so replace the hwtstamp_config with a mask of trapped
protocols saved per port. We also have the ptp_cmd to distinguish
between one-step and two-step PTP timestamping, so with those 2 bits of
information we can fully reconstruct a descriptive struct
hwtstamp_config for each port, during the SIOCGHWTSTAMP ioctl.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fd44b82b7 ]
PTP RX timestamping should be enabled when the user requests it, not by
default. If it is enabled by default, it can be problematic when the
ocelot driver is a DSA master, and it sidesteps what DSA tries to avoid
through __dsa_master_hwtstamp_validate().
Additionally, after the change which made ocelot trap PTP packets only
to the CPU at ocelot_hwtstamp_set() time, it is no longer even true that
RX timestamping is enabled by default, because until ocelot_hwtstamp_set()
is called, the PTP traps are actually not set up. So the rx_filter field
of ocelot->hwtstamp_config reflects an incorrect reality.
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1b355438b ]
efx_net_stats() (.ndo_get_stats64) can be called during an ethtool
selftest, during which time nic_data->mc_stats is NULL as the NIC has
been fini'd. In this case do not attempt to fetch the latest stats
from the hardware, else we will crash on a NULL dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000038
RIP efx_nic_update_stats
abridged calltrace:
efx_ef10_update_stats_pf
efx_net_stats
dev_get_stats
dev_seq_printf_stats
Skipping the read is safe, we will simply give out stale stats.
To ensure that the free in efx_ef10_fini_nic() does not race against
efx_ef10_update_stats_pf(), which could cause a TOCTTOU bug, take the
efx->stats_lock in fini_nic (it is already held across update_stats).
Fixes: d3142c193d ("sfc: refactor EF10 stats handling")
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1bc9fc4a0 ]
64-bit DMA detection will fail if axienet was started before (by boot
loader, boot ROM, etc). In this state axienet will not start properly.
XAXIDMA_TX_CDESC_OFFSET + 4 register (MM2S_CURDESC_MSB) is used to detect
64-bit DMA capability here. But datasheet says: When DMACR.RS is 1
(axienet is in enabled state), CURDESC_PTR becomes Read Only (RO) and
is used to fetch the first descriptor. So iowrite32()/ioread32() trick
to this register to detect 64-bit DMA will not work.
So move axienet reset before 64-bit DMA detection.
Fixes: f735c40ed9 ("net: axienet: Autodetect 64-bit DMA capability")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20230622192245.116864-1-fido_max@inbox.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4fc88ad2a ]
Commit 49725ffc15 ("net: stmmac: power up/down serdes in
stmmac_open/release") correctly added a call to the serdes_powerdown()
callback to stmmac_release() but did not remove the one from
stmmac_remove() which leads to a doubled call to serdes_powerdown().
This can lead to all kinds of problems: in the case of the qcom ethqos
driver, it caused an unbalanced regulator disable splat.
Fixes: 49725ffc15 ("net: stmmac: power up/down serdes in stmmac_open/release")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Junxiao Chang <junxiao.chang@intel.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230621135537.376649-1-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e8b2c88fc ]
The ice_ptp_extts_work() and ice_ptp_periodic_work() functions are both
scheduled on the same kthread worker, pf.ptp.kworker. The
ice_ptp_periodic_work() function sends to the firmware to interact with the
PHY, and must block to wait for responses.
This can cause delay in responding to the PFINT_OICR_TSYN_EVNT interrupt
cause, ultimately resulting in disruption to processing an input signal of
the frequency is high enough. In our testing, even 100 Hz signals get
disrupted.
Fix this by instead processing the signal inside the miscellaneous
interrupt thread prior to handling Tx timestamps.
Use atomic bits in a new pf->misc_thread bitmap in order to safely
communicate which tasks require processing within the
ice_misc_intr_thread_fn(). This ensures the communication of desired tasks
from the ice_misc_intr() are correctly processed without racing even in the
event that the interrupt triggers again before the thread function exits.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84214ab468 ]
When function igc_rx_hash() was introduced in v4.20 via commit 0507ef8a03
("igc: Add transmit and receive fastpath and interrupt handlers"), the
hardware wasn't configured to provide RSS hash, thus it made sense to not
enable net_device NETIF_F_RXHASH feature bit.
The NIC hardware was configured to enable RSS hash info in v5.2 via commit
2121c2712f ("igc: Add multiple receive queues control supporting"), but
forgot to set the NETIF_F_RXHASH feature bit.
The original implementation of igc_rx_hash() didn't extract the associated
pkt_hash_type, but statically set PKT_HASH_TYPE_L3. The largest portions of
this patch are about extracting the RSS Type from the hardware and mapping
this to enum pkt_hash_types. This was based on Foxville i225 software user
manual rev-1.3.1 and tested on Intel Ethernet Controller I225-LM (rev 03).
For UDP it's worth noting that RSS (type) hashing have been disabled both for
IPv4 and IPv6 (see IGC_MRQC_RSS_FIELD_IPV4_UDP + IGC_MRQC_RSS_FIELD_IPV6_UDP)
because hardware RSS doesn't handle fragmented pkts well when enabled (can
cause out-of-order). This results in PKT_HASH_TYPE_L3 for UDP packets, and
hash value doesn't include UDP port numbers. Not being PKT_HASH_TYPE_L4, have
the effect that netstack will do a software based hash calc calling into
flow_dissect, but only when code calls skb_get_hash(), which doesn't
necessary happen for local delivery.
For QA verification testing I wrote a small bpftrace prog:
[0] https://github.com/xdp-project/xdp-project/blob/master/areas/hints/monitor_skb_hash_on_dev.bt
Fixes: 2121c2712f ("igc: Add multiple receive queues control supporting")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/bpf/168182464270.616355.11391652654430626584.stgit@firesoul
Signed-off-by: Sasha Levin <sashal@kernel.org>
