commit 288b4fa179 upstream.
This reverts commit 18fc7c435b.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this code, the patch means that certain tegra_xusb_probe() will
fail if the firmware supports power-domains but CONFIG_PM is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 18fc7c435b ("usb: xhci: tegra: Fix error check")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/8baace8d-fb4b-41a4-ad5f-848ae643a23b@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c55afcbeaa upstream.
The ohci_hcd_at91_drv_suspend() sets ohci->rh_state to OHCI_RH_HALTED when
suspend which will let the ohci_irq() skip the interrupt after resume. And
nobody to handle this interrupt.
According to the comment in ohci_hcd_at91_drv_suspend(), it need to reset
when resume from suspend(MEM) to fix by setting "hibernated" argument of
ohci_resume().
Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230626152713.18950-1-aarongt.shen@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9b0328d0b upstream.
Some ZHAOXIN xHCI controllers follow usb3.1 spec, but only support
gen1 speed 5Gbps. While in Linux kernel, if xHCI suspport usb3.1,
root hub speed will show on 10Gbps.
To fix this issue of ZHAOXIN xHCI platforms, read usb speed ID
supported by xHCI to determine root hub speed. And add a quirk
XHCI_ZHAOXIN_HOST for this issue.
[fix warning about uninitialized symbol -Mathias]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-11-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a865a6522 upstream.
On some ZHAOXIN hosts, xHCI will prefetch TRB for performance
improvement. However this TRB prefetch mechanism may cross page boundary,
which may access memory not allocated by xHCI driver. In order to fix
this issue, two pages was allocated for a segment and only the first
page will be used. And add a quirk XHCI_ZHAOXIN_TRB_FETCH for this issue.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-10-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f927728186 upstream.
On ZHAOXIN ZX-100 project, xHCI can't work normally after resume
from system Sx state. To fix this issue, when resume from system
Sx state, reinitialize xHCI instead of restore.
So, Add XHCI_RESET_ON_RESUME quirk for ZX-100 to fix issue of
resuming from system Sx state.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-9-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe82f16aaf upstream.
This incorrect tracking caused unnecessary ring expansion in some
usecases which over days of use consume a lot of memory.
xhci driver tries to keep track of free transfer blocks (TRBs) on the
ring buffer, but failed to add back some cancelled transfers that were
turned into no-op operations instead of just moving past them.
This can happen if there are several queued pending transfers which
then are cancelled in reverse order.
Solve this by counting the numer of steps we move the dequeue pointer
once we complete a transfer, and add it to the number of free trbs
instead of just adding the trb number of the current transfer.
This way we ensure we count the no-op trbs on the way as well.
Fixes: 55f6153d8c ("xhci: remove extra loop in interrupt context")
Cc: stable@vger.kernel.org
Reported-by: Miller Hunter <MillerH@hearthnhome.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217242
Tested-by: Miller Hunter <MillerH@hearthnhome.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230515134059.161110-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a821fc313 upstream.
Donghun reports that a notebook that has an AMD Ryzen 5700U but supports
S3 has problems with USB after resuming from suspend. The issue was
bisected down to commit d1658268e4 ("usb: pci-quirks: disable D3cold on
xhci suspend for s2idle on AMD Renoir").
As this issue only happens on S3, narrow the broken D3cold quirk to only
run in s2idle.
Fixes: d1658268e4 ("usb: pci-quirks: disable D3cold on xhci suspend for s2idle on AMD Renoir")
Reported-and-tested-by: Donghun Yoon <donghun.yoon@lge.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230515134059.161110-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dddb342b5b upstream.
OverCurrent condition is not standardized in the UHCI spec.
Zhaoxin UHCI controllers report OverCurrent bit active off.
In order to handle OverCurrent condition correctly, the uhci-hcd
driver needs to be told to expect the active-off behavior.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230423105952.4526-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 735baf1b23 upstream.
Wire up the debugfs regset device pointer so that the controller is
resumed before accessing registers to avoid crashing or locking up if it
happens to be runtime suspended.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: stable@vger.kernel.org # 4.15: 30332eeefe: debugfs: regset32: Add Runtime PM support
Cc: stable@vger.kernel.org # 4.15
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230405090342.7363-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecaa490243 upstream.
Previously the quirk was skipped when no iommu was present. The same
rationale for skipping the quirk also applies in the iommu.passthrough=1
case.
Skip applying the XHCI_ZERO_64B_REGS quirk if the device's iommu domain is
passthrough.
Fixes: 12de0a35c9 ("xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers")
Cc: stable <stable@kernel.org>
Signed-off-by: D Scott Phillips <scott@os.amperecomputing.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230330143056.1390020-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6caea4855 upstream.
The command allocated to set exit latency LPM values need to be freed in
case the command is never queued. This would be the case if there is no
change in exit latency values, or device is missing.
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Link: https://lore.kernel.org/linux-usb/24263902-c9b3-ce29-237b-1c3d6918f4fe@alu.unizg.hr
Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Fixes: 5c2a380a5a ("xhci: Allocate separate command structures for each LPM command")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230330143056.1390020-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c7f9d2e41 upstream.
When we set the dual-role port to Host mode, we observed the following
splat:
[ 167.057718] BUG: sleeping function called from invalid context at
include/linux/sched/mm.h:229
[ 167.057872] Workqueue: events tegra_xusb_usb_phy_work
[ 167.057954] Call trace:
[ 167.057962] dump_backtrace+0x0/0x210
[ 167.057996] show_stack+0x30/0x50
[ 167.058020] dump_stack_lvl+0x64/0x84
[ 167.058065] dump_stack+0x14/0x34
[ 167.058100] __might_resched+0x144/0x180
[ 167.058140] __might_sleep+0x64/0xd0
[ 167.058171] slab_pre_alloc_hook.constprop.0+0xa8/0x110
[ 167.058202] __kmalloc_track_caller+0x74/0x2b0
[ 167.058233] kvasprintf+0xa4/0x190
[ 167.058261] kasprintf+0x58/0x90
[ 167.058285] tegra_xusb_find_port_node.isra.0+0x58/0xd0
[ 167.058334] tegra_xusb_find_port+0x38/0xa0
[ 167.058380] tegra_xusb_padctl_get_usb3_companion+0x38/0xd0
[ 167.058430] tegra_xhci_id_notify+0x8c/0x1e0
[ 167.058473] notifier_call_chain+0x88/0x100
[ 167.058506] atomic_notifier_call_chain+0x44/0x70
[ 167.058537] tegra_xusb_usb_phy_work+0x60/0xd0
[ 167.058581] process_one_work+0x1dc/0x4c0
[ 167.058618] worker_thread+0x54/0x410
[ 167.058650] kthread+0x188/0x1b0
[ 167.058672] ret_from_fork+0x10/0x20
The function tegra_xusb_padctl_get_usb3_companion eventually calls
tegra_xusb_find_port and this in turn calls kasprintf which might sleep
and so cannot be called from an atomic context.
Fix this by moving the call to tegra_xusb_padctl_get_usb3_companion to
the tegra_xhci_id_work function where it is really needed.
Fixes: f836e78430 ("usb: xhci-tegra: Add OTG support")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Link: https://lore.kernel.org/r/20230327095548.1599470-1-haotienh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0fbd2cda92 ]
Walking the dram->cs array was seen as accesses beyond the first array
item by the compiler. Instead, use the array index directly. This allows
for run-time bounds checking under CONFIG_UBSAN_BOUNDS as well. Seen
with GCC 13 with -fstrict-flex-arrays:
In function 'xhci_mvebu_mbus_config',
inlined from 'xhci_mvebu_mbus_init_quirk' at ../drivers/usb/host/xhci-mvebu.c:66:2:
../drivers/usb/host/xhci-mvebu.c:37:28: warning: array subscript 0 is outside array bounds of 'const struct mbus_dram_window[0]' [-Warray-bounds=]
37 | writel(((cs->size - 1) & 0xffff0000) | (cs->mbus_attr << 8) |
| ~~^~~~~~
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230204183651.never.663-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c26e682afc ]
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20230202153235.2412790-7-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a95f62d581 ]
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: Olav Kongas <ok@artecdesign.ee>
Link: https://lore.kernel.org/r/20230202153235.2412790-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b4040f452 ]
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230202153235.2412790-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1523c4dbc ]
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20230202153235.2412790-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a3f82c79c ]
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230202153235.2412790-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7efe3fc7c ]
To update the I/O pins, the registers are read/modified/written. The
read operation incorrectly always read the first register. Although
wrong, there wasn't any impact as all the output pins are always
written, and the inputs are read only anyway.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20230207033337.18112-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5d3d01ae15 upstream.
Commit ca07e1c1e4 ("drivers:usb:fsl:Make fsl ehci drv an independent
driver module") changed DRV_NAME which was used for MODULE_ALIAS as well.
Starting from this the module alias didn't match the platform device
name created in fsl-mph-dr-of.c
Change DRV_NAME to match the driver name for host mode in fsl-mph-dr-of.
This is needed for module autoloading on ls1021a.
Fixes: ca07e1c1e4 ("drivers:usb:fsl:Make fsl ehci drv an independent driver module")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20230120122714.3848784-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74622f0a81 upstream.
USB3 ports on xHC hosts may have retimers that cause too long
exit latency to work with native USB3 U1/U2 link power management states.
For now only use usb_acpi_port_lpm_incapable() to evaluate if port lpm
should be disabled while setting up the USB3 roothub.
Other ways to identify lpm incapable ports can be added here later if
ACPI _DSM does not exist.
Limit this to Intel hosts for now, this is to my knowledge only
an Intel issue.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0522b9a165 upstream.
One USB3 roothub port may support link power management, while another
root port on the same xHC can't due to different retimers used for
the ports.
This is the case with Intel Alder Lake, and possible future platforms
where retimers used for USB4 ports cause too long exit latecy to
enable native USB3 lpm U1 and U2 states.
Add a flag in the xhci port structure to indicate if the port is
lpm_incapable, and check it while calculating exit latency.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23a3b8d5a2 upstream.
Allow PCI hosts to check and tune roothub and port settings
before the hub is up and running.
This override is needed to turn off U1 and U2 LPM for some ports
based on per port ACPI _DSM, _UPC, or possibly vendor specific mmio
values for Intel xHC hosts.
Usb core calls the host update_hub_device once it creates a hub.
Entering U1 or U2 link power save state on ports with this limitation
will cause link to fail, turning the usb device unusable in that setup.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2bc47c43e upstream.
Make sure xhci_free_dev() and xhci_kill_endpoint_urbs() do not race
and cause null pointer dereference when host suddenly dies.
Usb core may call xhci_free_dev() which frees the xhci->devs[slot_id]
virt device at the same time that xhci_kill_endpoint_urbs() tries to
loop through all the device's endpoints, checking if there are any
cancelled urbs left to give back.
hold the xhci spinlock while freeing the virt device
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8fb5bc76e upstream.
When the host controller is not responding, all URBs queued to all
endpoints need to be killed. This can cause a kernel panic if we
dereference an invalid endpoint.
Fix this by using xhci_get_virt_ep() helper to find the endpoint and
checking if the endpoint is valid before dereferencing it.
[233311.853271] xhci-hcd xhci-hcd.1.auto: xHCI host controller not responding, assume dead
[233311.853393] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
[233311.853964] pc : xhci_hc_died+0x10c/0x270
[233311.853971] lr : xhci_hc_died+0x1ac/0x270
[233311.854077] Call trace:
[233311.854085] xhci_hc_died+0x10c/0x270
[233311.854093] xhci_stop_endpoint_command_watchdog+0x100/0x1a4
[233311.854105] call_timer_fn+0x50/0x2d4
[233311.854112] expire_timers+0xac/0x2e4
[233311.854118] run_timer_softirq+0x300/0xabc
[233311.854127] __do_softirq+0x148/0x528
[233311.854135] irq_exit+0x194/0x1a8
[233311.854143] __handle_domain_irq+0x164/0x1d0
[233311.854149] gic_handle_irq.22273+0x10c/0x188
[233311.854156] el1_irq+0xfc/0x1a8
[233311.854175] lpm_cpuidle_enter+0x25c/0x418 [msm_pm]
[233311.854185] cpuidle_enter_state+0x1f0/0x764
[233311.854194] do_idle+0x594/0x6ac
[233311.854201] cpu_startup_entry+0x7c/0x80
[233311.854209] secondary_start_kernel+0x170/0x198
Fixes: 50e8725e7c ("xhci: Refactor command watchdog and fix split string.")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Hu <hhhuuu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <0fe978ed-8269-9774-1c40-f8a98c17e838@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a157512097 upstream.
Make sure to also limit the amount of soft reset retries for transaction
errors on streams in cases where the transaction error event doesn't point
to any specific TRB.
In these cases we don't know the TRB or stream ring, but we do know which
endpoint had the error.
To keep error counting simple and functional, move the current err_count
from ring structure to endpoint structure.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03a88b0baf upstream.
Can not set the @shared_hcd to NULL before decrease the usage count
by usb_put_hcd(), this will cause the shared hcd not released.
Fixes: 04284eb74e ("usb: xhci-mtk: add support runtime PM")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20221128063337.18124-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fed70b61ef upstream.
ADL-N systems have the same issue as ADL-P, where a large boot firmware
delay is seen if USB ports are left in U3 at shutdown. So apply the
XHCI_RESET_TO_DEFAULT quirk to ADL-N as well.
This patch depends on commit 34cd2db408 ("xhci: Add quirk to reset
host back to default state at shutdown").
The issue it fixes is a ~20s boot time delay when booting from S5. It
affects ADL-N devices, and ADL-N support was added starting from v5.16.
Cc: stable@vger.kernel.org
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
What the code does is to not check the return value from
devm_gpiod_get() and then avoid using an erroneous GPIO descriptor
with IS_ERR_OR_NULL().
This will miss real errors from the GPIO core that should not be
ignored, such as probe deferral.
Instead request the GPIO as explicitly optional, which means that
if it doesn't exist, the descriptor returned will be NULL.
Then we can add error handling and also avoid just doing this on
the device tree path, and simplify the site where the optional
GPIO descriptor is used.
There were some problems with cleaning up this GPIO descriptor
use in the past, but this is the proper way to deal with it.
Cc: Rafał Miłecki <rafal@milecki.pl>
Cc: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20221107090753.1404679-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoints are normally deleted from the bandwidth list when they are
dropped, before the virt device is freed.
If xHC host is dying or being removed then the endpoints aren't dropped
cleanly due to functions returning early to avoid interacting with a
non-accessible host controller.
So check and delete endpoints that are still on the bandwidth list when
freeing the virt device.
Solves a list_del corruption kernel crash when unbinding xhci-pci,
caused by xhci_mem_cleanup() when it later tried to delete already freed
endpoints from the bandwidth list.
This only affects hosts that use software bandwidth checking, which
currenty is only the xHC in intel Panther Point PCH (Ivy Bridge)
Cc: stable@vger.kernel.org
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-5-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For optimal power consumption of USB4 routers the XHCI PCIe endpoint
used for tunneling must be in D3. Historically this is accomplished
by a long list of PCIe IDs that correspond to these endpoints because
the xhci_hcd driver will not default to allowing runtime PM for all
devices.
As both AMD and Intel have released new products with new XHCI controllers
this list continues to grow. In reviewing the XHCI specification v1.2 on
page 607 there is already a requirement that the PCI power management
states D3hot and D3cold must be supported.
In the quirk list, use this to indicate that runtime PM should be allowed
on XHCI controllers. The following controllers are known to be xHC 1.2 and
dropped explicitly:
* AMD Yellow Carp
* Intel Alder Lake
* Intel Meteor Lake
* Intel Raptor Lake
[keep PCI ID for Alder Lake PCH for recently added quirk -Mathias]
Cc: stable@vger.kernel.org
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://www.intel.com/content/dam/www/public/us/en/documents/technical-specifications/extensible-host-controler-interface-usb-xhci.pdf
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-4-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems based on Alder Lake P see significant boot time delay if
boot firmware tries to control usb ports in unexpected link states.
This is seen with self-powered usb devices that survive in U3 link
suspended state over S5.
A more generic solution to power off ports at shutdown was attempted in
commit 83810f84ec ("xhci: turn off port power in shutdown")
but it caused regression.
Add host specific XHCI_RESET_TO_DEFAULT quirk which will reset host and
ports back to default state in shutdown.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-3-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This appears to fix the error:
"xhci_hcd <address>; ERROR Transfer event TRB DMA ptr not part of
current TD ep_index 2 comp_code 13" that appear spuriously (or pretty
often) when using a r8152 USB3 ethernet adapter with integrated hub.
ASM1042 reports as a 0.96 controller, but appears to behave more like 1.0
Inspired by this email thread: https://markmail.org/thread/7vzqbe7t6du6qsw3
Cc: stable@vger.kernel.org
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-2-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch switches the driver from using legacy gpio API to the newer
gpiod API.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220927220504.3744878-2-dmitry.torokhov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci used to test if link power management (LPM) capable USB2 devices
really could enter and exit L1 state link state.
Failed devices were added to a lpm_failed_dev list.
This feature was removed 9 years ago in
commit de68bab4fa ("usb: Don't enable USB 2.0 Link PM by default.")
but lpm_failed_dev member was still left.
Remove it now.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The u32 command was added to struct xhci_hcd over 10 years ago in
commit 9777e3ce90 ("USB: xHCI: bus power management implementation")
It wasn't even used back then, so remove it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Show the completion code of a unsuccessful "enable slot" command.
Add it in a human readable form to the existing error message.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b328f8002 ("xhci: re-initialize the HC during resume if HCE was
set") introduced a new warning message when the host controller error
was set and re-initializing.
This is expected behavior on some designs which already set
`xhci->broken_suspend` so the new warning is alarming to some users.
Modify the code to only show the warning if this was a surprising behavior
to the XHCI driver.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216470
Fixes: 8b328f8002 ("xhci: re-initialize the HC during resume if HCE was set")
Reported-by: Artem S. Tashkinov <aros@gmx.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DbC is already in use, then the allocated memory for the xhci_dbc struct
doesn't get freed before returning NULL, which leads to a memleak.
Fixes: 534675942e ("xhci: dbc: refactor xhci_dbc_init()")
Cc: stable@vger.kernel.org
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_alloc_stream_info() allocates stream context array for stream_info
->stream_ctx_array with xhci_alloc_stream_ctx(). When some error occurs,
stream_info->stream_ctx_array is not released, which will lead to a
memory leak.
We can fix it by releasing the stream_info->stream_ctx_array with
xhci_free_stream_ctx() on the error path to avoid the potential memory
leak.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop another couple of pointless pr_info() calls, and drop a number of
instances of hcd_name variables that are no longer referenced now that
they are no longer printed to the log at driver registration time.
Fixes: 10174220f5 ("usb: reduce kernel log spam on driver registration")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220905111740.352348-1-ardb@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ohci retaining bogus hardware states cause usb disconnect devices
connected before hibernation(s4), this issue occur when ohci-platform
driver build as a module and the built-in ohci-platform driver will
re probe and re enumerate the devices, so there will be no such problem.
Avoid retaining bogus hardware states during resume-from-hibernation.
Previously we had reset the hardware as part of preparing to reinstate
the snapshot image. But we can do better now with the new PM framework,
since we know exactly which resume operations are from hibernation.
According to the commit 'cd1965db05 ("USB: ohci: move ohci_pci_{
suspend,resume} to ohci-hcd.c")' and commit '6ec4beb5c7 ("USB: new
flag for resume-from-hibernation")', the flag "hibernated" is for
resume-from-hibernation and it should be true when usb resume from disk.
When this flag "hibernated" is set, the drivers will reset the hardware
to get rid of any existing state and make sure resume from hibernation
re-enumerates everything for ohci.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Link: https://lore.kernel.org/r/20220902063639.17875-1-zhuyinbo@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves the merge issue in:
drivers/usb/dwc3/gadget.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the HC driver is now passed to the function with its
own parameter (it used to be picked from id->driver_data),
the id parameter serves no purpose.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220831125052.71584-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
