commit 2c507ce90e upstream.
Kernel uses `struct virtio_net_ctrl_rss` to save command-specific-data
for both the VIRTIO_NET_CTRL_MQ_HASH_CONFIG and
VIRTIO_NET_CTRL_MQ_RSS_CONFIG commands.
According to the VirtIO standard, "Field reserved MUST contain zeroes.
It is defined to make the structure to match the layout of
virtio_net_rss_config structure, defined in 5.1.6.5.7.".
Yet for the VIRTIO_NET_CTRL_MQ_HASH_CONFIG command case, the `max_tx_vq`
field in struct virtio_net_ctrl_rss, which corresponds to the
`reserved` field in struct virtio_net_hash_config, is not zeroed,
thereby violating the VirtIO standard.
This patch solves this problem by zeroing this field in
virtnet_init_default_rss().
Cc: Andrew Melnychenko <andrew@daynix.com>
Cc: stable@vger.kernel.org
Fixes: c7114b1249 ("drivers/net/virtio_net: Added basic RSS support.")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230810110405.25558-1-yin31149@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 43d00e102d ]
ADQ and switchdev are not supported simultaneously. Enabling both at the
same time can result in nullptr dereference.
To prevent this, check if ADQ is active when changing devlink mode to
switchdev mode, and check if switchdev is active when enabling ADQ.
Fixes: fbc7b27af0 ("ice: enable ndo_setup_tc support for mqprio_qdisc")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230816193405.1307580-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eb9625a3a ]
While performing certain power-off sequences, PCI drivers are
called to suspend and resume their underlying devices through
PCI PM (power management) interface. However this NIC hardware
does not support PCI PM suspend/resume operations so system wide
suspend/resume leads to bad MFW (management firmware) state which
causes various follow-up errors in driver when communicating with
the device/firmware afterwards.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding
system to go into suspended/standby mode.
Without this fix device/firmware does not recover unless system
is power cycled.
Fixes: 2950219d87 ("qede: Add basic network device support")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230816150711.59035-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa165e1949 ]
In efx_init_tc(), move the setting of efx->tc->up after the
flow_indr_dev_register() call, so that if it fails, efx_fini_tc()
won't call flow_indr_dev_unregister().
Fixes: 5b2e12d51b ("sfc: bind indirect blocks for TC offload on EF100")
Suggested-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/a81284d7013aba74005277bd81104e4cfbea3f6f.1692114888.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23d775f12d ]
If the switch is reset during active EEPROM transactions, as in
just after an SoC reset after power up, the I2C bus transaction
may be cut short leaving the EEPROM internal I2C state machine
in the wrong state. When the switch is reset again, the bad
state machine state may result in data being read from the wrong
memory location causing the switch to enter unexpected mode
rendering it inoperational.
Fixes: a3dcb3e7e7 ("net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset")
Signed-off-by: Alfred Lee <l00g33k@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815001323.24739-1-l00g33k@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f2beb8874 ]
Change "write" into the actual "read" word.
Change parameters description.
Fixes: 7073f46e44 ("i40e: Add AQ commands for NVM Update for X722")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 751969e5b1 ]
Return an error if a field's mask is neither full nor empty. When a mask
is only partial the field is not being used for rule programming but it
gives a wrong impression it is used. Fix by returning an error on any
partial mask to make it clear they are not supported.
The ip_ver assignment is moved earlier in code to allow using it in
iavf_validate_fdir_fltr_masks.
Fixes: 527691bf06 ("iavf: Support IPv4 Flow Director filters")
Fixes: e90cbc257a ("iavf: Support IPv6 Flow Director filters")
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dafcbce071 ]
Similar to commit 01f4fd2708 ("bonding: Fix incorrect deletion of
ETH_P_8021AD protocol vid from slaves"), we can trigger BUG_ON(!vlan_info)
in unregister_vlan_dev() with the following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add team1 type team
# ip netns exec ns1 ip link add team_slave type veth peer veth2
# ip netns exec ns1 ip link set team_slave master team1
# ip netns exec ns1 ip link add link team_slave name team_slave.10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link team1 name team1.10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set team_slave nomaster
# ip netns del ns1
Add S-VLAN tag related features support to team driver. So the team driver
will always propagate the VLAN info to its slaves.
Fixes: 8ad227ff89 ("net: vlan: add 802.1ad support")
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230814032301.2804971-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 096516d092 ]
The 54810 does not support c45. The mmd_phy_indirect accesses return
arbirtary values leading to odd behavior like saying it supports EEE
when it doesn't. We also see that reading/writing these non-existent
MMD registers leads to phy instability in some cases.
Fixes: b14995ac25 ("net: phy: broadcom: Add BCM54810 PHY entry")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/1691901708-28650-1-git-send-email-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28458c8000 ]
tx_timeout_task is canceled too early when removing the driver. Nothing
prevents .ndo_tx_timeout from triggering and queuing the work again.
Better cancel it after the netdev is unregistered.
It's harmless for octep_tx_timeout_task to run in the window between the
unregistration and cancelation, because it checks netif_running.
Fixes: 862cd659a6 ("octeon_ep: Add driver framework and device initialization")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://lore.kernel.org/r/20230810150114.107765-3-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c461e394d ]
On Zynq UltraScale+ MPSoC ubuntu platform when systemctl issues suspend,
network manager bring down the interface and goes into suspend. When it
wakes up it again enables the interface.
This leads to xilinx-psgtr "PLL lock timeout" on interface bringup, as
the power management controller power down the entire FPD (including
SERDES) if none of the FPD devices are in use and serdes is not
initialized on resume.
$ sudo rtcwake -m no -s 120 -v
$ sudo systemctl suspend <this does ifconfig eth1 down>
$ ifconfig eth1 up
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
phy phy-fd400000.phy.0: phy poweron failed --> -110
macb driver is called in this way:
1. macb_close: Stop network interface. In this function, it
reset MACB IP and disables PHY and network interface.
2. macb_suspend: It is called in kernel suspend flow. But because
network interface has been disabled(netif_running(ndev) is
false), it does nothing and returns directly;
3. System goes into suspend state. Some time later, system is
waken up by RTC wakeup device;
4. macb_resume: It does nothing because network interface has
been disabled;
5. macb_open: It is called to enable network interface again. ethernet
interface is initialized in this API but serdes which is power-off
by PMUFW during FPD-off suspend is not initialized again and so
we hit GT PLL lock issue on open.
To resolve this PLL timeout issue always do PS GTR initialization
when ethernet device is configured as non-wakeup source.
Fixes: f22bd29ba1 ("net: macb: Fix ZynqMP SGMII non-wakeup source resume failure")
Fixes: 8b73fa3ae0 ("net: macb: Added ZynqMP-specific initialization")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1691414091-2260697-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc941e548b ]
Uwe reports:
"Most PHYs signal WoL using an interrupt. So disabling interrupts [at
shutdown] breaks WoL at least on PHYs covered by the marvell driver."
Discussing with Ioana, the problem which was trying to be solved was:
"The board in question is a LS1021ATSN which has two AR8031 PHYs that
share an interrupt line. In case only one of the PHYs is probed and
there are pending interrupts on the PHY#2 an IRQ storm will happen
since there is no entity to clear the interrupt from PHY#2's registers.
PHY#1's driver will get stuck in .handle_interrupt() indefinitely."
Further confirmation that "the two AR8031 PHYs are on the same MDIO
bus."
With WoL using interrupts to wake the system, in such a case, the
system will begin booting with an asserted interrupt. Thus, we need to
cope with an interrupt asserted during boot.
Solve this instead by disabling interrupts during PHY probe. This will
ensure in Ioana's situation that both PHYs of the same type sharing an
interrupt line on a common MDIO bus will have their interrupt outputs
disabled when the driver probes the device, but before we hook in any
interrupt handlers - thus avoiding the interrupt storm.
A better fix would be for platform firmware to disable the interrupting
devices at source during boot, before control is handed to the kernel.
Fixes: e2f016cf77 ("net: phy: add a shutdown procedure")
Link: 20230804071757.383971-1-u.kleine-koenig@pengutronix.de
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 829c6524d6 ]
The reference of pdev->dev is taken by of_find_device_by_node, so
it should be released when not need anymore.
Fixes: 7dc54d3b8d ("net: pcs: add Renesas MII converter driver")
Signed-off-by: Xiang Yang <xiangyang3@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51b813176f ]
Commit 25266128fe ("virtio-net: fix race between set queues and
probe") tries to fix the race between set queues and probe by calling
_virtnet_set_queues() before DRIVER_OK is set. This violates virtio
spec. Fixing this by setting queues after virtio_device_ready().
Note that rtnl needs to be held for userspace requests to change the
number of queues. So we are serialized in this way.
Fixes: 25266128fe ("virtio-net: fix race between set queues and probe")
Reported-by: Dragos Tatulea <dtatulea@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f62d221a4 ]
In virtnet_probe(), if the device doesn't provide a MAC address the
driver assigns a random one.
As we modify the MAC address we need to notify the device to allow it
to update all the related information.
The problem can be seen with vDPA and mlx5_vdpa driver as it doesn't
assign a MAC address by default. The virtio_net device uses a random
MAC address (we can see it with "ip link"), but we can't ping a net
namespace from another one using the virtio-vdpa device because the
new MAC address has not been provided to the hardware:
RX packets are dropped since they don't go through the receive filters,
TX packets go through unaffected.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 51b813176f ("virtio-net: set queues after driver_ok")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ce29c17dc ]
igc_configure_rx_ring() function will be called as part of XDP program
setup. If Rx hardware timestamp is enabled prio to XDP program setup,
this timestamp enablement will be overwritten when buffer size is
written into SRRCTL register.
Thus, this commit read the register value before write to SRRCTL
register. This commit is tested by using xdp_hw_metadata bpf selftest
tool. The tool enables Rx hardware timestamp and then attach XDP program
to igc driver. It will display hardware timestamp of UDP packet with
port number 9092. Below are detail of test steps and results.
Command on DUT:
sudo ./xdp_hw_metadata <interface name>
Command on Link Partner:
echo -n skb | nc -u -q1 <destination IPv4 addr> 9092
Result before this patch:
skb hwtstamp is not found!
Result after this patch:
found skb hwtstamp = 1677800973.642836757
Optionally, read PHC to confirm the values obtained are almost the same:
Command:
sudo ./testptp -d /dev/ptp0 -g
Result:
clock time: 1677800973.913598978 or Fri Mar 3 07:49:33 2023
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.14+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e58f30246c ]
In commit 7beecaf7d5 ("net: phy: at803x: improve the WOL feature"), it
seems not correct to use a wol_en bit in a 1588 Control Register which is
only available on AR8031/AR8033(share the same phy_id) to determine if WoL
is enabled. Change it back to use AT803X_INTR_ENABLE_WOL for determining
the WoL status which is applicable on all chips supporting wol. Also update
the at803x_set_wol() function to only update the 1588 register on chips
having it. After this change, disabling wol at probe from commit
d7cd5e06c9 ("net: phy: at803x: disable WOL at probe") is no longer
needed. Change it to just disable the WoL bit in 1588 register for
AR8031/AR8033 to be aligned with AT803X_INTR_ENABLE_WOL in probe.
Fixes: 7beecaf7d5 ("net: phy: at803x: improve the WOL feature")
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Viorel Suman <viorel.suman@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 988e8d90b3 ]
Use devm_regulator_get_enable_optional() instead of hand writing it. It
saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: e58f30246c ("net: phy: at803x: fix the wol setting functions")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6db541ae27 upstream.
If a login request fails, the recovery process should be protected
against parallel resets. It is a known issue that freeing and
registering CRQ's in quick succession can result in a failover CRQ from
the VIOS. Processing a failover during login recovery is dangerous for
two reasons:
1. This will result in two parallel initialization processes, this can
cause serious issues during login.
2. It is possible that the failover CRQ is received but never executed.
We get notified of a pending failover through a transport event CRQ.
The reset is not performed until a INIT CRQ request is received.
Previously, if CRQ init fails during login recovery, then the ibmvnic
irq is freed and the login process returned error. If failover_pending
is true (a transport event was received), then the ibmvnic device
would never be able to process the reset since it cannot receive the
CRQ_INIT request due to the irq being freed. This leaved the device
in a inoperable state.
Therefore, the login failure recovery process must be hardened against
these possible issues. Possible failovers (due to quick CRQ free and
init) must be avoided and any issues during re-initialization should be
dealt with instead of being propagated up the stack. This logic is
similar to that of ibmvnic_probe().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-5-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23cc5f6674 upstream.
Perform a partial reset before sending a login request if any of the
following are true:
1. If a previous request times out. This can be dangerous because the
VIOS could still receive the old login request at any point after
the timeout. Therefore, it is best to re-register the CRQ's and
sub-CRQ's before retrying.
2. If the previous request returns an error that is not described in
PAPR. PAPR provides procedures if the login returns with partial
success or aborted return codes (section L.5.1) but other values
do not have a defined procedure. Previously, these conditions
just returned error from the login function rather than trying
to resolve the issue.
This can cause further issues since most callers of the login
function are not prepared to handle an error when logging in. This
improper cleanup can lead to the device being permanently DOWN'd.
For example, if the VIOS believes that the device is already logged
in then it will return INVALID_STATE (-7). If we never re-register
CRQ's then it will always think that the device is already logged
in. This leaves the device inoperable.
The partial reset involves freeing the sub-CRQs, freeing the CRQ then
registering and initializing a new CRQ and sub-CRQs. This essentially
restarts all communication with VIOS to allow for a fresh login attempt
that will be unhindered by any previous failed attempts.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-4-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d78a671eb8 upstream.
Rather than leaving the DMA unmapping of the login buffers to the
login response handler, move this work into the login release functions.
Previously, these functions were only used for freeing the allocated
buffers. This could lead to issues if there are more than one
outstanding login buffer requests, which is possible if a login request
times out.
If a login request times out, then there is another call to send login.
The send login function makes a call to the login buffer release
function. In the past, this freed the buffers but did not DMA unmap.
Therefore, the VIOS could still write to the old login (now freed)
buffer. It is for this reason that it is a good idea to leave the DMA
unmap call to the login buffers release function.
Since the login buffer release functions now handle DMA unmapping,
remove the duplicate DMA unmapping in handle_login_rsp().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-3-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 411c565b4b upstream.
If the LOGIN CRQ fails to send then we must DMA unmap the response
buffer. Previously, if the CRQ failed then the memory was freed without
DMA unmapping.
Fixes: c98d9cc417 ("ibmvnic: send_login should check for crq errors")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-2-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db17ba719b upstream.
Ensure that all offsets in a login response buffer are within the size
of the allocated response buffer. Any offsets or lengths that surpass
the allocation are likely the result of an incomplete response buffer.
In these cases, a full reset is necessary.
When attempting to login, the ibmvnic device will allocate a response
buffer and pass a reference to the VIOS. The VIOS will then send the
ibmvnic device a LOGIN_RSP CRQ to signal that the buffer has been filled
with data. If the ibmvnic device does not get a response in 20 seconds,
the old buffer is freed and a new login request is sent. With 2
outstanding requests, any LOGIN_RSP CRQ's could be for the older
login request. If this is the case then the login response buffer (which
is for the newer login request) could be incomplete and contain invalid
data. Therefore, we must enforce strict sanity checks on the response
buffer values.
Testing has shown that the `off_rxadd_buff_size` value is filled in last
by the VIOS and will be the smoking gun for these circumstances.
Until VIOS can implement a mechanism for tracking outstanding response
buffers and a method for mapping a LOGIN_RSP CRQ to a particular login
response buffer, the best ibmvnic can do in this situation is perform a
full reset.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aab8e1a200 upstream.
Handling pci errors should fully teardown and load back auxiliary
devices, same as done through mlx5 health recovery flow.
Fixes: 72ed5d5624 ("net/mlx5: Suspend auxiliary devices only in case of PCI device suspend")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d006207625 upstream.
When device is in error state, marked by the flag
MLX5_DEVICE_STATE_INTERNAL_ERROR, the HW and PCI may not be accessible
and so clock update work should be skipped. Furthermore, such access
through PCI in error state, after calling mlx5_pci_disable_device() can
result in failing to recover from pci errors.
Fixes: ef9814deaf ("net/mlx5e: Add HW timestamping (TS) support")
Reported-and-tested-by: Ganesh G R <ganeshgr@linux.ibm.com>
Closes: https://lore.kernel.org/netdev/9bdb9b9d-140a-7a28-f0de-2e64e873c068@nvidia.com
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dc2b3922d upstream.
When querying eswitch functions 0 is a valid number of host VFs. After
introducing ARM SRIOV falling through to getting the max value from PCI
results in using the total VFs allowed on the ARM for the host.
Fixes: 86eec50bea ("net/mlx5: Support querying max VFs from device");
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e3d20617b upstream.
hns3_dbg_fill_content()/hclge_dbg_fill_content() is aim to integrate some
items to a string for content, and we add '\n' and '\0' in the last
two bytes of content.
strscpy() will add '\0' in the last byte of destination buffer(one of
items), it result in finishing content print ahead of schedule and some
dump content truncation.
One Error log shows as below:
cat mac_list/uc
UC MAC_LIST:
Expected:
UC MAC_LIST:
FUNC_ID MAC_ADDR STATE
pf 00:2b:19:05:03:00 ACTIVE
The destination buffer is length-bounded and not required to be
NUL-terminated, so just change strscpy() to memcpy() to fix it.
Fixes: 1cf3d5567f ("net: hns3: fix strncpy() not using dest-buf length as length issue")
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20230809020902.1941471-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac6257a3ae upstream.
When externel_lb and reset are executed together, a deadlock may
occur:
[ 3147.217009] INFO: task kworker/u321:0:7 blocked for more than 120 seconds.
[ 3147.230483] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 3147.238999] task:kworker/u321:0 state:D stack: 0 pid: 7 ppid: 2 flags:0x00000008
[ 3147.248045] Workqueue: hclge hclge_service_task [hclge]
[ 3147.253957] Call trace:
[ 3147.257093] __switch_to+0x7c/0xbc
[ 3147.261183] __schedule+0x338/0x6f0
[ 3147.265357] schedule+0x50/0xe0
[ 3147.269185] schedule_preempt_disabled+0x18/0x24
[ 3147.274488] __mutex_lock.constprop.0+0x1d4/0x5dc
[ 3147.279880] __mutex_lock_slowpath+0x1c/0x30
[ 3147.284839] mutex_lock+0x50/0x60
[ 3147.288841] rtnl_lock+0x20/0x2c
[ 3147.292759] hclge_reset_prepare+0x68/0x90 [hclge]
[ 3147.298239] hclge_reset_subtask+0x88/0xe0 [hclge]
[ 3147.303718] hclge_reset_service_task+0x84/0x120 [hclge]
[ 3147.309718] hclge_service_task+0x2c/0x70 [hclge]
[ 3147.315109] process_one_work+0x1d0/0x490
[ 3147.319805] worker_thread+0x158/0x3d0
[ 3147.324240] kthread+0x108/0x13c
[ 3147.328154] ret_from_fork+0x10/0x18
In externel_lb process, the hns3 driver call napi_disable()
first, then the reset happen, then the restore process of the
externel_lb will fail, and will not call napi_enable(). When
doing externel_lb again, napi_disable() will be double call,
cause a deadlock of rtnl_lock().
This patch use the HNS3_NIC_STATE_DOWN state to protect the
calling of napi_disable() and napi_enable() in externel_lb
process, just as the usage in ndo_stop() and ndo_start().
Fixes: 04b6ba1435 ("net: hns3: add support for external loopback test")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6265e242f7 upstream.
In some configure flow of hns3 driver, for example, change mtu, it will
disable MAC through firmware before configuration. But firmware disables
MAC asynchronously. The rx traffic may be not stopped in this case.
So fixes it by waiting until mac link is down.
Fixes: a9775bb64a ("net: hns3: fix set and get link ksettings issue")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08469dacfa upstream.
Some nic configurations could only be performed after link is down. So this
patch refactor this API for reuse.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a94c16a2fd upstream.
When the tagging protocol in current use is "ocelot-8021q" and we unbind
the driver, we see this splat:
$ echo '0000:00:00.2' > /sys/bus/pci/drivers/fsl_enetc/unbind
mscc_felix 0000:00:00.5 swp0: left promiscuous mode
sja1105 spi2.0: Link is Down
DSA: tree 1 torn down
mscc_felix 0000:00:00.5 swp2: left promiscuous mode
sja1105 spi2.2: Link is Down
DSA: tree 3 torn down
fsl_enetc 0000:00:00.2 eno2: left promiscuous mode
mscc_felix 0000:00:00.5: Link is Down
------------[ cut here ]------------
RTNL: assertion failed at net/dsa/tag_8021q.c (409)
WARNING: CPU: 1 PID: 329 at net/dsa/tag_8021q.c:409 dsa_tag_8021q_unregister+0x12c/0x1a0
Modules linked in:
CPU: 1 PID: 329 Comm: bash Not tainted 6.5.0-rc3+ #771
pc : dsa_tag_8021q_unregister+0x12c/0x1a0
lr : dsa_tag_8021q_unregister+0x12c/0x1a0
Call trace:
dsa_tag_8021q_unregister+0x12c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
RTNL: assertion failed at net/8021q/vlan_core.c (376)
WARNING: CPU: 1 PID: 329 at net/8021q/vlan_core.c:376 vlan_vid_del+0x1b8/0x1f0
CPU: 1 PID: 329 Comm: bash Tainted: G W 6.5.0-rc3+ #771
pc : vlan_vid_del+0x1b8/0x1f0
lr : vlan_vid_del+0x1b8/0x1f0
dsa_tag_8021q_unregister+0x8c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
DSA: tree 0 torn down
This was somewhat not so easy to spot, because "ocelot-8021q" is not the
default tagging protocol, and thus, not everyone who tests the unbinding
path may have switched to it beforehand. The default
felix_tag_npi_teardown() does not require rtnl_lock() to be held.
Fixes: 7c83a7c539 ("net: dsa: add a second tagger for Ocelot switches based on tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230803134253.2711124-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7791cec23 upstream.
Since the AR8032 part does not support wol, remove related callbacks
from it.
Fixes: 5800091a20 ("net: phy: at803x: add support for AR8032 PHY")
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fb1d8eb23 upstream.
Add fdir_fltr_lock locking in unprotected places.
The change in iavf_fdir_is_dup_fltr adds a spinlock around a loop which
iterates over all filters and looks for a duplicate. The filter can be
removed from list and freed from memory at the same time it's being
compared. All other places where filters are deleted are already
protected with spinlock.
The remaining changes protect adapter->fdir_active_fltr variable so now
all its uses are under a spinlock.
Fixes: 527691bf06 ("iavf: Support IPv4 Flow Director filters")
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230807205011.3129224-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1c936e9af upstream.
In case rhashtable_lookup_insert_fast() fails inside vxlan_vni_add(), the
allocated percpu vni stats are not freed on the error path.
Introduce vxlan_vni_free() which would work as a nice wrapper to free
vxlan_vni_node resources properly.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 4095e0e132 ("drivers: vxlan: vnifilter: per vni stats")
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59eeb23294 upstream.
Using the syzkaller repro with reduced packet size it was discovered
that XDP_PACKET_HEADROOM is not checked in tun_can_build_skb(),
although pad may be incremented in tun_build_skb(). This may end up
with exceeding the PAGE_SIZE limit in tun_build_skb().
Jason Wang <jasowang@redhat.com> proposed to count XDP_PACKET_HEADROOM
always (e.g. without rcu_access_pointer(tun->xdp_prog)) in
tun_can_build_skb() since there's a window during which XDP program
might be attached between tun_can_build_skb() and tun_build_skb().
Fixes: 7df13219d7 ("tun: reserve extra headroom only when XDP is set")
Link: https://syzkaller.appspot.com/bug?extid=f817490f5bd20541b90a
Signed-off-by: Andrew Kanner <andrew.kanner@gmail.com>
Link: https://lore.kernel.org/r/20230803185947.2379988-1-andrew.kanner@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01f4fd2708 upstream.
BUG_ON(!vlan_info) is triggered in unregister_vlan_dev() with
following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add bond0 type bond mode 0
# ip netns exec ns1 ip link add bond_slave_1 type veth peer veth2
# ip netns exec ns1 ip link set bond_slave_1 master bond0
# ip netns exec ns1 ip link add link bond_slave_1 name vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link bond0 name bond0_vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set bond_slave_1 nomaster
# ip netns del ns1
The logical analysis of the problem is as follows:
1. create ETH_P_8021AD protocol vlan10 for bond_slave_1:
register_vlan_dev()
vlan_vid_add()
vlan_info_alloc()
__vlan_vid_add() // add [ETH_P_8021AD, 10] vid to bond_slave_1
2. create ETH_P_8021AD protocol bond0_vlan10 for bond0:
register_vlan_dev()
vlan_vid_add()
__vlan_vid_add()
vlan_add_rx_filter_info()
if (!vlan_hw_filter_capable(dev, proto)) // condition established because bond0 without NETIF_F_HW_VLAN_STAG_FILTER
return 0;
if (netif_device_present(dev))
return dev->netdev_ops->ndo_vlan_rx_add_vid(dev, proto, vid); // will be never called
// The slaves of bond0 will not refer to the [ETH_P_8021AD, 10] vid.
3. detach bond_slave_1 from bond0:
__bond_release_one()
vlan_vids_del_by_dev()
list_for_each_entry(vid_info, &vlan_info->vid_list, list)
vlan_vid_del(dev, vid_info->proto, vid_info->vid);
// bond_slave_1 [ETH_P_8021AD, 10] vid will be deleted.
// bond_slave_1->vlan_info will be assigned NULL.
4. delete vlan10 during delete ns1:
default_device_exit_batch()
dev->rtnl_link_ops->dellink() // unregister_vlan_dev() for vlan10
vlan_info = rtnl_dereference(real_dev->vlan_info); // real_dev of vlan10 is bond_slave_1
BUG_ON(!vlan_info); // bond_slave_1->vlan_info is NULL now, bug is triggered!!!
Add S-VLAN tag related features support to bond driver. So the bond driver
will always propagate the VLAN info to its slaves.
Fixes: 8ad227ff89 ("net: vlan: add 802.1ad support")
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230802114320.4156068-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32d0a49d36 upstream.
syzbot/KCSAN reported data-races in macsec whenever dev->stats fields
are updated.
It appears all of these updates can happen from multiple cpus.
Adopt SMP safe DEV_STATS_INC() to update dev->stats fields.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7dfeda6fd upstream.
When unloading the MANA driver, mana_dealloc_queues() waits for the MANA
hardware to complete any inflight packets and set the pending send count
to zero. But if the hardware has failed, mana_dealloc_queues()
could wait forever.
Fix this by adding a timeout to the wait. Set the timeout to 120 seconds,
which is a somewhat arbitrary value that is more than long enough for
functional hardware to complete any sends.
Cc: stable@vger.kernel.org
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Link: https://lore.kernel.org/r/1691576525-24271-1-git-send-email-schakrabarti@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46622219aa upstream.
In the allowedips self-test, nodes are inserted into the tree, but it
generated an even amount of nodes, but for checking maximum node depth,
there is of course the root node, which makes the total number
necessarily odd. With two few nodes added, it never triggered the
maximum depth check like it should have. So, add 129 nodes instead of
128 nodes, and do so with a more straightforward scheme, starting with
all the bits set, and shifting over one each time. Then increase the
maximum depth to 129, and choose a better name for that variable to
make it clear that it represents depth as opposed to bits.
Cc: stable@vger.kernel.org
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20230807132146.2191597-2-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b74bb07cda upstream.
RX full flags are raised if certain types of RX FIFO are full, and then
drop all following MPDU of AMPDU. In order to resume to receive MPDU
when RX FIFO becomes available, we clear the register bits by the
commit a0d99ebb3e ("wifi: rtw89: initialize DMA of CMAC"). But, 8852AE
needs more settings to support this. To quickly fix disconnection problem,
revert the behavior as before.
Fixes: a0d99ebb3e ("wifi: rtw89: initialize DMA of CMAC")
Reported-by: Damian B <bronecki.damian@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217710
Cc: <Stable@vger.kernel.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Damian B <bronecki.damian@gmail.com>
Link: https://lore.kernel.org/r/20230808005426.5327-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 421033deb9 upstream.
On DBDC devices the first (internal) phy is only capable of using
2.4 GHz band, and the 5 GHz band is exposed via a separate phy object,
so avoid the false advertising.
Reported-by: Rani Hod <rani.hod@gmail.com>
Closes: https://github.com/openwrt/openwrt/pull/12361
Fixes: 7660a1bd0c ("mt76: mt7615: register ext_phy if DBDC is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230605073408.8699-1-fercerpav@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c9241f3ce upstream.
Commit 66b2c338ad initializes the "sk_uid" field in the protocol socket
(struct sock) from the "/dev/tapX" device node's owner UID. Per original
commit 86741ec254 ("net: core: Add a UID field to struct sock.",
2016-11-04), that's wrong: the idea is to cache the UID of the userspace
process that creates the socket. Commit 86741ec254 mentions socket() and
accept(); with "tap", the action that creates the socket is
open("/dev/tapX").
Therefore the device node's owner UID is irrelevant. In most cases,
"/dev/tapX" will be owned by root, so in practice, commit 66b2c338ad has
no observable effect:
- before, "sk_uid" would be zero, due to undefined behavior
(CVE-2023-1076),
- after, "sk_uid" would be zero, due to "/dev/tapX" being owned by root.
What matters is the (fs)UID of the process performing the open(), so cache
that in "sk_uid".
Cc: Eric Dumazet <edumazet@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Pietro Borrello <borrello@diag.uniroma1.it>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: 66b2c338ad ("tap: tap_open(): correctly initialize socket uid")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2173435
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bc3047374 upstream.
Commit a096ccca6e initializes the "sk_uid" field in the protocol socket
(struct sock) from the "/dev/net/tun" device node's owner UID. Per
original commit 86741ec254 ("net: core: Add a UID field to struct
sock.", 2016-11-04), that's wrong: the idea is to cache the UID of the
userspace process that creates the socket. Commit 86741ec254 mentions
socket() and accept(); with "tun", the action that creates the socket is
open("/dev/net/tun").
Therefore the device node's owner UID is irrelevant. In most cases,
"/dev/net/tun" will be owned by root, so in practice, commit a096ccca6e
has no observable effect:
- before, "sk_uid" would be zero, due to undefined behavior
(CVE-2023-1076),
- after, "sk_uid" would be zero, due to "/dev/net/tun" being owned by root.
What matters is the (fs)UID of the process performing the open(), so cache
that in "sk_uid".
Cc: Eric Dumazet <edumazet@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Pietro Borrello <borrello@diag.uniroma1.it>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: a096ccca6e ("tun: tun_chr_open(): correctly initialize socket uid")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2173435
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b99225b4fe upstream.
The SL-A300, B500/5600, and C700 devices no longer auto-load because of
"usbnet: Remove over-broad module alias from zaurus."
This patch adds IDs for those 3 devices.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217632
Fixes: 16adf5d079 ("usbnet: Remove over-broad module alias from zaurus.")
Signed-off-by: Ross Maynard <bids.7405@bigpond.com>
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/69b5423b-2013-9fc9-9569-58e707d9bafb@bigpond.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b755c25fbc ]
When both supported and previous version have the same major version,
and the firmwares are missing, the driver ends in a loop requesting the
same (previous) version over and over again:
[ 76.327413] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
[ 76.339802] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.352162] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.364502] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.376848] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.389183] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.401522] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.413860] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.426199] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
...
Fix this by inverting the check to that we aren't yet at the previous
version, and also check the minor version.
This also catches the case where both versions are the same, as it was
after commit bb5dbf2cc6 ("net: marvell: prestera: add firmware v4.0
support").
With this fix applied:
[ 88.499622] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
[ 88.511995] Prestera DX 0000:01:00.0: failed to request previous firmware: mrvl/prestera/mvsw_prestera_fw-v4.0.img
[ 88.522403] Prestera DX: probe of 0000:01:00.0 failed with error -2
Fixes: 47f26018a4 ("net: marvell: prestera: try to load previous fw version")
Signed-off-by: Jonas Gorski <jonas.gorski@bisdn.de>
Acked-by: Elad Nachman <enachman@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Taras Chornyi <taras.chornyi@plvision.eu>
Link: https://lore.kernel.org/r/20230802092357.163944-1-jonas.gorski@bisdn.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c635ca45a7 ]
In the cited commit, new type of FS_TYPE_PRIO_CHAINS fs_prio was added
to support multiple parallel namespaces for multi-chains. And we skip
all the flow tables under the fs_node of this type unconditionally,
when searching for the next or previous flow table to connect for a
new table.
As this search function is also used for find new root table when the
old one is being deleted, it will skip the entire FS_TYPE_PRIO_CHAINS
fs_node next to the old root. However, new root table should be chosen
from it if there is any table in it. Fix it by skipping only the flow
tables in the same FS_TYPE_PRIO_CHAINS fs_node when finding the
closest FT for a fs_node.
Besides, complete the connecting from FTs of previous priority of prio
because there should be multiple prevs after this fs_prio type is
introduced. And also the next FT should be chosen from the first flow
table next to the prio in the same FS_TYPE_PRIO_CHAINS fs_prio, if
this prio is the first child.
Fixes: 328edb499f ("net/mlx5: Split FDB fast path prio to multiple namespaces")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/7a95754df479e722038996c97c97b062b372591f.1690803944.git.leonro@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 618d28a535 ]
As find_closest_ft_recursive is called to find the closest FT, the
first parameter of find_closest_ft can be changed from fs_prio to
fs_node. Thus this function is extended to find the closest FT for the
nodes of any type, not only prios, but also the sub namespaces.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/d3962c2b443ec8dde7a740dc742a1f052d5e256c.1690803944.git.leonro@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: c635ca45a7 ("net/mlx5: fs_core: Skip the FTs in the same FS_TYPE_PRIO_CHAINS fs_prio")
Signed-off-by: Sasha Levin <sashal@kernel.org>
