commit b642f4c5f3 upstream.
txs may be dropped if the frame is aggregated in AMSDU. When the problem
shows up, some SKBs would be hold in driver to cause network stopped
temporarily. Even if the problem can be recovered by txs timeout handling,
mt7921 still need to disable txs in AMSDU to avoid this issue.
Cc: stable@vger.kernel.org
Fixes: 163f4d22c1 ("mt76: mt7921: add MAC support")
Reviewed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 569820befb upstream.
enetc_phc_index is only used via symbol_get, which was only ever
intended for very internal symbols like this one. Use EXPORT_SYMBOL_GPL
for it so that symbol_get can enforce only being used on
EXPORT_SYMBOL_GPL symbols.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfedba3b2c upstream.
When building for power4, newer binutils don't recognise the "dcbfl"
extended mnemonic.
dcbfl RA, RB is equivalent to dcbf RA, RB, 1.
Switch to "dcbf" to avoid the build error.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e74216b8de ]
The commit 14af9963ba ("bonding: Support macvlans on top of tlb/rlb mode
bonds") aims to enable the use of macvlans on top of rlb bond mode. However,
the current rlb bond mode only handles ARP packets to update remote neighbor
entries. This causes an issue when a macvlan is on top of the bond, and
remote devices send packets to the macvlan using the bond's MAC address
as the destination. After delivering the packets to the macvlan, the macvlan
will rejects them as the MAC address is incorrect. Consequently, this commit
makes macvlan over bond non-functional.
To address this problem, one potential solution is to check for the presence
of a macvlan port on the bond device using netif_is_macvlan_port(bond->dev)
and return NULL in the rlb_arp_xmit() function. However, this approach
doesn't fully resolve the situation when a VLAN exists between the bond and
macvlan.
So let's just do a partial revert for commit 14af9963ba in rlb_arp_xmit().
As the comment said, Don't modify or load balance ARPs that do not originate
locally.
Fixes: 14af9963ba ("bonding: Support macvlans on top of tlb/rlb mode bonds")
Reported-by: susan.zheng@veritas.com
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2117816
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9525a3c38a ]
Add check for pf->vf not being NULL before dereferencing
pf->vf[vsi->vf_id] in updating VSI filter sync.
Add a similar check before dereferencing !pf->vf[vsi->vf_id].trusted
in the condition for clearing promisc mode bit.
Fixes: c87c938f62 ("i40e: Add VF VLAN pruning")
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de43975721 ]
The IGC_PTM_CTRL_SHRT_CYC defines the time between two consecutive PTM
requests. The bit resolution of this field is six bits. That bit five was
missing in the mask. This patch comes to correct the typo in the
IGC_PTM_CTRL_SHRT_CYC macro.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://lore.kernel.org/r/20230821171721.2203572-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ecff05e6c ]
This reverts commit 7255355a06.
After this commit we are not able to attach VF to VM:
virsh attach-interface v0 hostdev --managed 0000:41:01.0 --mac 52:52:52:52:52:52
error: Failed to attach interface
error: Cannot set interface MAC to 52:52:52:52:52:52 for ifname enp65s0f0np0 vf 0: Resource temporarily unavailable
ice_check_vf_ready_for_cfg() already contain waiting for reset.
New condition in ice_check_vf_ready_for_reset() causing only problems.
Fixes: 7255355a06 ("ice: Fix ice VF reset during iavf initialization")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10083aef78 ]
The driver is misconfiguring the hardware for some values of MTU such that
it could use multiple descriptors to receive a packet when it could have
simply used one.
Change the driver to use a round-up instead of the result of a shift, as
the shift can truncate the lower bits of the size, and result in the
problem noted above. It also aligns this driver with similar code in i40e.
The insidiousness of this problem is that everything works with the wrong
size, it's just not working as well as it could, as some MTU sizes end up
using two or more descriptors, and there is no way to tell that is
happening without looking at ice_trace or a bus analyzer.
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f866fbc842 ]
UDP sendmsg() is lockless, so ip_select_ident_segs()
can very well be run from multiple cpus [1]
Convert inet->inet_id to an atomic_t, but implement
a dedicated path for TCP, avoiding cost of a locked
instruction (atomic_add_return())
Note that this patch will cause a trivial merge conflict
because we added inet->flags in net-next tree.
v2: added missing change in
drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_cm.c
(David Ahern)
[1]
BUG: KCSAN: data-race in __ip_make_skb / __ip_make_skb
read-write to 0xffff888145af952a of 2 bytes by task 7803 on cpu 1:
ip_select_ident_segs include/net/ip.h:542 [inline]
ip_select_ident include/net/ip.h:556 [inline]
__ip_make_skb+0x844/0xc70 net/ipv4/ip_output.c:1446
ip_make_skb+0x233/0x2c0 net/ipv4/ip_output.c:1560
udp_sendmsg+0x1199/0x1250 net/ipv4/udp.c:1260
inet_sendmsg+0x63/0x80 net/ipv4/af_inet.c:830
sock_sendmsg_nosec net/socket.c:725 [inline]
sock_sendmsg net/socket.c:748 [inline]
____sys_sendmsg+0x37c/0x4d0 net/socket.c:2494
___sys_sendmsg net/socket.c:2548 [inline]
__sys_sendmmsg+0x269/0x500 net/socket.c:2634
__do_sys_sendmmsg net/socket.c:2663 [inline]
__se_sys_sendmmsg net/socket.c:2660 [inline]
__x64_sys_sendmmsg+0x57/0x60 net/socket.c:2660
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
read to 0xffff888145af952a of 2 bytes by task 7804 on cpu 0:
ip_select_ident_segs include/net/ip.h:541 [inline]
ip_select_ident include/net/ip.h:556 [inline]
__ip_make_skb+0x817/0xc70 net/ipv4/ip_output.c:1446
ip_make_skb+0x233/0x2c0 net/ipv4/ip_output.c:1560
udp_sendmsg+0x1199/0x1250 net/ipv4/udp.c:1260
inet_sendmsg+0x63/0x80 net/ipv4/af_inet.c:830
sock_sendmsg_nosec net/socket.c:725 [inline]
sock_sendmsg net/socket.c:748 [inline]
____sys_sendmsg+0x37c/0x4d0 net/socket.c:2494
___sys_sendmsg net/socket.c:2548 [inline]
__sys_sendmmsg+0x269/0x500 net/socket.c:2634
__do_sys_sendmmsg net/socket.c:2663 [inline]
__se_sys_sendmmsg net/socket.c:2660 [inline]
__x64_sys_sendmmsg+0x57/0x60 net/socket.c:2660
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x184d -> 0x184e
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7804 Comm: syz-executor.1 Not tainted 6.5.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/26/2023
==================================================================
Fixes: 23f57406b8 ("ipv4: avoid using shared IP generator for connected sockets")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f534f6581e ]
veth and vxcan need to make sure the ifindexes of the peer
are not negative, core does not validate this.
Using iproute2 with user-space-level checking removed:
Before:
# ./ip link add index 10 type veth peer index -1
# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether 52:54:00:74:b2:03 brd ff:ff:ff:ff:ff:ff
10: veth1@veth0: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 8a:90:ff:57:6d:5d brd ff:ff:ff:ff:ff:ff
-1: veth0@veth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ae:ed:18:e6:fa:7f brd ff:ff:ff:ff:ff:ff
Now:
$ ./ip link add index 10 type veth peer index -1
Error: ifindex can't be negative.
This problem surfaced in net-next because an explicit WARN()
was added, the root cause is older.
Fixes: e6f8f1a739 ("veth: Allow to create peer link with given ifindex")
Fixes: a8f820a380 ("can: add Virtual CAN Tunnel driver (vxcan)")
Reported-by: syzbot+5ba06978f34abb058571@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32bbe64a13 ]
The fixed_phy_register() function returns error pointers and never
returns NULL. Update the checks accordingly.
Fixes: b0ba512e25 ("net: bcmgenet: enable driver to work without a device tree")
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23a14488ea ]
The fixed_phy_register() function returns error pointers and never
returns NULL. Update the checks accordingly.
Fixes: c25b23b8a3 ("bgmac: register fixed PHY for ARM BCM470X / BCM5301X chipsets")
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e94b590abf ]
802.1X PAE frames are link-local frames, therefore they must be trapped to
the CPU port. Currently, the MT753X switches treat 802.1X PAE frames as
regular multicast frames, therefore flooding them to user ports. To fix
this, set 802.1X PAE frames to be trapped to the CPU port(s).
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 348c976be0 ]
The field 'virtual router' was extended to 12 bits in Spectrum-4.
Therefore, the element 'MLXSW_AFK_ELEMENT_VIRT_ROUTER_MSB' needs 3 bits for
Spectrum < 4 and 4 bits for Spectrum >= 4.
The elements are stored in an internal storage scratchpad. Currently, the
MSB is defined there as 3 bits. It means that for Spectrum-4, only 2K VRFs
can be used for multicast routing, as the highest bit is not really used by
the driver. Fix the definition of 'VIRT_ROUTER_MSB' to use 4 bits. Adjust
the definitions of 'virtual router' field in the blocks accordingly - use
'_avoid_size_check' for Spectrum-2 instead of for Spectrum-4. Fix the mask
in parse function to use 4 bits.
Fixes: 6d5d8ebb88 ("mlxsw: Rename virtual router flex key element")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/79bed2b70f6b9ed58d4df02e9798a23da648015b.1692268427.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dc63b9cfd ]
The two most significant bits of the "local_port" field in the SSPR
register are always cleared since they are overwritten by the deprecated
and overlapping "sub_port" field.
On systems with more than 255 local ports (e.g., Spectrum-4), this
results in the firmware maintaining invalid mappings between system port
and local port. Specifically, two different systems ports (0x1 and
0x101) point to the same local port (0x1), which eventually leads to
firmware errors.
Fix by removing the deprecated "sub_port" field.
Fixes: fd24b29a1b ("mlxsw: reg: Align existing registers to use extended local_port field")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/9b909a3033c8d3d6f67f237306bef4411c5e6ae4.1692268427.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc2de151ab ]
Currently, in Spectrum-2 and above, time stamps are extracted from the CQE
into the time stamp fields in 'struct mlxsw_skb_cb', only when the CQE
time stamp type is UTC. The time stamps are read directly from the CQE and
software can get the time stamp in UTC format using CQEv2.
From Spectrum-4, the time stamps that are read from the CQE are allowed
to be also from MIRROR_UTC type.
Therefore, we get a warning [1] from the driver that the time stamp fields
were not set, when LLDP control packet is sent.
Allow the time stamp type to be MIRROR_UTC and set the time stamp in this
case as well.
[1]
WARNING: CPU: 11 PID: 0 at drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c:1409 mlxsw_sp2_ptp_hwtstamp_fill+0x1f/0x70 [mlxsw_spectrum]
[...]
Call Trace:
<IRQ>
mlxsw_sp2_ptp_receive+0x3c/0x80 [mlxsw_spectrum]
mlxsw_core_skb_receive+0x119/0x190 [mlxsw_core]
mlxsw_pci_cq_tasklet+0x3c9/0x780 [mlxsw_pci]
tasklet_action_common.constprop.0+0x9f/0x110
__do_softirq+0xbb/0x296
irq_exit_rcu+0x79/0xa0
common_interrupt+0x86/0xa0
</IRQ>
<TASK>
Fixes: 4735402173 ("mlxsw: spectrum: Extend to support Spectrum-4 ASIC")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/bcef4d044ef608a4e258d33a7ec0ecd91f480db5.1692268427.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 043d5f68d0 ]
There are two network devices(veth1 and veth3) in ns1, and ipvlan1 with
L3S mode and ipvlan2 with L2 mode are created based on them as
figure (1). In this case, ipvlan_register_nf_hook() will be called to
register nf hook which is needed by ipvlans in L3S mode in ns1 and value
of ipvl_nf_hook_refcnt is set to 1.
(1)
ns1 ns2
------------ ------------
veth1--ipvlan1 (L3S)
veth3--ipvlan2 (L2)
(2)
ns1 ns2
------------ ------------
veth1--ipvlan1 (L3S)
ipvlan2 (L2) veth3
| |
|------->-------->--------->--------
migrate
When veth3 migrates from ns1 to ns2 as figure (2), veth3 will register in
ns2 and calls call_netdevice_notifiers with NETDEV_REGISTER event:
dev_change_net_namespace
call_netdevice_notifiers
ipvlan_device_event
ipvlan_migrate_l3s_hook
ipvlan_register_nf_hook(newnet) (I)
ipvlan_unregister_nf_hook(oldnet) (II)
In function ipvlan_migrate_l3s_hook(), ipvl_nf_hook_refcnt in ns1 is not 0
since veth1 with ipvlan1 still in ns1, (I) and (II) will be called to
register nf_hook in ns2 and unregister nf_hook in ns1. As a result,
ipvl_nf_hook_refcnt in ns1 is decreased incorrectly and this in ns2
is increased incorrectly. When the second net namespace is removed, a
reference count leak warning in ipvlan_ns_exit() will be triggered.
This patch add a check before ipvlan_migrate_l3s_hook() is called. The
warning can be triggered as follows:
$ ip netns add ns1
$ ip netns add ns2
$ ip netns exec ns1 ip link add veth1 type veth peer name veth2
$ ip netns exec ns1 ip link add veth3 type veth peer name veth4
$ ip netns exec ns1 ip link add ipv1 link veth1 type ipvlan mode l3s
$ ip netns exec ns1 ip link add ipv2 link veth3 type ipvlan mode l2
$ ip netns exec ns1 ip link set veth3 netns ns2
$ ip net del ns2
Fixes: 3133822f5a ("ipvlan: use pernet operations and restrict l3s hooks to master netns")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20230817145449.141827-1-luwei32@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d44036cad3 ]
The blamed commit resolved a bug where frames would still get stuck at
egress, even though they're smaller than the maxSDU[tc], because the
driver did not take into account the extra 33 ns that the queue system
needs for scheduling the frame.
It now takes that into account, but the arithmetic that we perform in
vsc9959_tas_remaining_gate_len_ps() is buggy, because we operate on
64-bit unsigned integers, so gate_len_ns - VSC9959_TAS_MIN_GATE_LEN_NS
may become a very large integer if gate_len_ns < 33 ns.
In practice, this means that we've introduced a regression where all
traffic class gates which are permanently closed will not get detected
by the driver, and we won't enable oversize frame dropping for them.
Before:
mscc_felix 0000:00:00.5: port 0: max frame size 1526 needs 12400000 ps, 1152000 ps for mPackets at speed 1000
mscc_felix 0000:00:00.5: port 0 tc 0 min gate len 1000000, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 1 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 2 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 3 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 4 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 5 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 6 min gate len 0, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 5120 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 615 octets including FCS
After:
mscc_felix 0000:00:00.5: port 0: max frame size 1526 needs 12400000 ps, 1152000 ps for mPackets at speed 1000
mscc_felix 0000:00:00.5: port 0 tc 0 min gate len 1000000, sending all frames
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 5120 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 615 octets including FCS
Fixes: 11afdc6526 ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230817120111.3522827-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05f3d5bc23 ]
On SDP interfaces, frame oversize and undersize errors are
observed as driver is not considering packet sizes of all
subscribers of the link before updating the link config.
This patch fixes the same.
Fixes: 9b7dd87ac0 ("octeontx2-af: Support to modify min/max allowed packet lengths")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230817063006.10366-1-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2c507ce90e upstream.
Kernel uses `struct virtio_net_ctrl_rss` to save command-specific-data
for both the VIRTIO_NET_CTRL_MQ_HASH_CONFIG and
VIRTIO_NET_CTRL_MQ_RSS_CONFIG commands.
According to the VirtIO standard, "Field reserved MUST contain zeroes.
It is defined to make the structure to match the layout of
virtio_net_rss_config structure, defined in 5.1.6.5.7.".
Yet for the VIRTIO_NET_CTRL_MQ_HASH_CONFIG command case, the `max_tx_vq`
field in struct virtio_net_ctrl_rss, which corresponds to the
`reserved` field in struct virtio_net_hash_config, is not zeroed,
thereby violating the VirtIO standard.
This patch solves this problem by zeroing this field in
virtnet_init_default_rss().
Cc: Andrew Melnychenko <andrew@daynix.com>
Cc: stable@vger.kernel.org
Fixes: c7114b1249 ("drivers/net/virtio_net: Added basic RSS support.")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230810110405.25558-1-yin31149@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 43d00e102d ]
ADQ and switchdev are not supported simultaneously. Enabling both at the
same time can result in nullptr dereference.
To prevent this, check if ADQ is active when changing devlink mode to
switchdev mode, and check if switchdev is active when enabling ADQ.
Fixes: fbc7b27af0 ("ice: enable ndo_setup_tc support for mqprio_qdisc")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230816193405.1307580-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eb9625a3a ]
While performing certain power-off sequences, PCI drivers are
called to suspend and resume their underlying devices through
PCI PM (power management) interface. However this NIC hardware
does not support PCI PM suspend/resume operations so system wide
suspend/resume leads to bad MFW (management firmware) state which
causes various follow-up errors in driver when communicating with
the device/firmware afterwards.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding
system to go into suspended/standby mode.
Without this fix device/firmware does not recover unless system
is power cycled.
Fixes: 2950219d87 ("qede: Add basic network device support")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230816150711.59035-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa165e1949 ]
In efx_init_tc(), move the setting of efx->tc->up after the
flow_indr_dev_register() call, so that if it fails, efx_fini_tc()
won't call flow_indr_dev_unregister().
Fixes: 5b2e12d51b ("sfc: bind indirect blocks for TC offload on EF100")
Suggested-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/a81284d7013aba74005277bd81104e4cfbea3f6f.1692114888.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23d775f12d ]
If the switch is reset during active EEPROM transactions, as in
just after an SoC reset after power up, the I2C bus transaction
may be cut short leaving the EEPROM internal I2C state machine
in the wrong state. When the switch is reset again, the bad
state machine state may result in data being read from the wrong
memory location causing the switch to enter unexpected mode
rendering it inoperational.
Fixes: a3dcb3e7e7 ("net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset")
Signed-off-by: Alfred Lee <l00g33k@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815001323.24739-1-l00g33k@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f2beb8874 ]
Change "write" into the actual "read" word.
Change parameters description.
Fixes: 7073f46e44 ("i40e: Add AQ commands for NVM Update for X722")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 751969e5b1 ]
Return an error if a field's mask is neither full nor empty. When a mask
is only partial the field is not being used for rule programming but it
gives a wrong impression it is used. Fix by returning an error on any
partial mask to make it clear they are not supported.
The ip_ver assignment is moved earlier in code to allow using it in
iavf_validate_fdir_fltr_masks.
Fixes: 527691bf06 ("iavf: Support IPv4 Flow Director filters")
Fixes: e90cbc257a ("iavf: Support IPv6 Flow Director filters")
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dafcbce071 ]
Similar to commit 01f4fd2708 ("bonding: Fix incorrect deletion of
ETH_P_8021AD protocol vid from slaves"), we can trigger BUG_ON(!vlan_info)
in unregister_vlan_dev() with the following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add team1 type team
# ip netns exec ns1 ip link add team_slave type veth peer veth2
# ip netns exec ns1 ip link set team_slave master team1
# ip netns exec ns1 ip link add link team_slave name team_slave.10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link team1 name team1.10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set team_slave nomaster
# ip netns del ns1
Add S-VLAN tag related features support to team driver. So the team driver
will always propagate the VLAN info to its slaves.
Fixes: 8ad227ff89 ("net: vlan: add 802.1ad support")
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230814032301.2804971-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 096516d092 ]
The 54810 does not support c45. The mmd_phy_indirect accesses return
arbirtary values leading to odd behavior like saying it supports EEE
when it doesn't. We also see that reading/writing these non-existent
MMD registers leads to phy instability in some cases.
Fixes: b14995ac25 ("net: phy: broadcom: Add BCM54810 PHY entry")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/1691901708-28650-1-git-send-email-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28458c8000 ]
tx_timeout_task is canceled too early when removing the driver. Nothing
prevents .ndo_tx_timeout from triggering and queuing the work again.
Better cancel it after the netdev is unregistered.
It's harmless for octep_tx_timeout_task to run in the window between the
unregistration and cancelation, because it checks netif_running.
Fixes: 862cd659a6 ("octeon_ep: Add driver framework and device initialization")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://lore.kernel.org/r/20230810150114.107765-3-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c461e394d ]
On Zynq UltraScale+ MPSoC ubuntu platform when systemctl issues suspend,
network manager bring down the interface and goes into suspend. When it
wakes up it again enables the interface.
This leads to xilinx-psgtr "PLL lock timeout" on interface bringup, as
the power management controller power down the entire FPD (including
SERDES) if none of the FPD devices are in use and serdes is not
initialized on resume.
$ sudo rtcwake -m no -s 120 -v
$ sudo systemctl suspend <this does ifconfig eth1 down>
$ ifconfig eth1 up
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
phy phy-fd400000.phy.0: phy poweron failed --> -110
macb driver is called in this way:
1. macb_close: Stop network interface. In this function, it
reset MACB IP and disables PHY and network interface.
2. macb_suspend: It is called in kernel suspend flow. But because
network interface has been disabled(netif_running(ndev) is
false), it does nothing and returns directly;
3. System goes into suspend state. Some time later, system is
waken up by RTC wakeup device;
4. macb_resume: It does nothing because network interface has
been disabled;
5. macb_open: It is called to enable network interface again. ethernet
interface is initialized in this API but serdes which is power-off
by PMUFW during FPD-off suspend is not initialized again and so
we hit GT PLL lock issue on open.
To resolve this PLL timeout issue always do PS GTR initialization
when ethernet device is configured as non-wakeup source.
Fixes: f22bd29ba1 ("net: macb: Fix ZynqMP SGMII non-wakeup source resume failure")
Fixes: 8b73fa3ae0 ("net: macb: Added ZynqMP-specific initialization")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1691414091-2260697-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc941e548b ]
Uwe reports:
"Most PHYs signal WoL using an interrupt. So disabling interrupts [at
shutdown] breaks WoL at least on PHYs covered by the marvell driver."
Discussing with Ioana, the problem which was trying to be solved was:
"The board in question is a LS1021ATSN which has two AR8031 PHYs that
share an interrupt line. In case only one of the PHYs is probed and
there are pending interrupts on the PHY#2 an IRQ storm will happen
since there is no entity to clear the interrupt from PHY#2's registers.
PHY#1's driver will get stuck in .handle_interrupt() indefinitely."
Further confirmation that "the two AR8031 PHYs are on the same MDIO
bus."
With WoL using interrupts to wake the system, in such a case, the
system will begin booting with an asserted interrupt. Thus, we need to
cope with an interrupt asserted during boot.
Solve this instead by disabling interrupts during PHY probe. This will
ensure in Ioana's situation that both PHYs of the same type sharing an
interrupt line on a common MDIO bus will have their interrupt outputs
disabled when the driver probes the device, but before we hook in any
interrupt handlers - thus avoiding the interrupt storm.
A better fix would be for platform firmware to disable the interrupting
devices at source during boot, before control is handed to the kernel.
Fixes: e2f016cf77 ("net: phy: add a shutdown procedure")
Link: 20230804071757.383971-1-u.kleine-koenig@pengutronix.de
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 829c6524d6 ]
The reference of pdev->dev is taken by of_find_device_by_node, so
it should be released when not need anymore.
Fixes: 7dc54d3b8d ("net: pcs: add Renesas MII converter driver")
Signed-off-by: Xiang Yang <xiangyang3@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51b813176f ]
Commit 25266128fe ("virtio-net: fix race between set queues and
probe") tries to fix the race between set queues and probe by calling
_virtnet_set_queues() before DRIVER_OK is set. This violates virtio
spec. Fixing this by setting queues after virtio_device_ready().
Note that rtnl needs to be held for userspace requests to change the
number of queues. So we are serialized in this way.
Fixes: 25266128fe ("virtio-net: fix race between set queues and probe")
Reported-by: Dragos Tatulea <dtatulea@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f62d221a4 ]
In virtnet_probe(), if the device doesn't provide a MAC address the
driver assigns a random one.
As we modify the MAC address we need to notify the device to allow it
to update all the related information.
The problem can be seen with vDPA and mlx5_vdpa driver as it doesn't
assign a MAC address by default. The virtio_net device uses a random
MAC address (we can see it with "ip link"), but we can't ping a net
namespace from another one using the virtio-vdpa device because the
new MAC address has not been provided to the hardware:
RX packets are dropped since they don't go through the receive filters,
TX packets go through unaffected.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 51b813176f ("virtio-net: set queues after driver_ok")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ce29c17dc ]
igc_configure_rx_ring() function will be called as part of XDP program
setup. If Rx hardware timestamp is enabled prio to XDP program setup,
this timestamp enablement will be overwritten when buffer size is
written into SRRCTL register.
Thus, this commit read the register value before write to SRRCTL
register. This commit is tested by using xdp_hw_metadata bpf selftest
tool. The tool enables Rx hardware timestamp and then attach XDP program
to igc driver. It will display hardware timestamp of UDP packet with
port number 9092. Below are detail of test steps and results.
Command on DUT:
sudo ./xdp_hw_metadata <interface name>
Command on Link Partner:
echo -n skb | nc -u -q1 <destination IPv4 addr> 9092
Result before this patch:
skb hwtstamp is not found!
Result after this patch:
found skb hwtstamp = 1677800973.642836757
Optionally, read PHC to confirm the values obtained are almost the same:
Command:
sudo ./testptp -d /dev/ptp0 -g
Result:
clock time: 1677800973.913598978 or Fri Mar 3 07:49:33 2023
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.14+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e58f30246c ]
In commit 7beecaf7d5 ("net: phy: at803x: improve the WOL feature"), it
seems not correct to use a wol_en bit in a 1588 Control Register which is
only available on AR8031/AR8033(share the same phy_id) to determine if WoL
is enabled. Change it back to use AT803X_INTR_ENABLE_WOL for determining
the WoL status which is applicable on all chips supporting wol. Also update
the at803x_set_wol() function to only update the 1588 register on chips
having it. After this change, disabling wol at probe from commit
d7cd5e06c9 ("net: phy: at803x: disable WOL at probe") is no longer
needed. Change it to just disable the WoL bit in 1588 register for
AR8031/AR8033 to be aligned with AT803X_INTR_ENABLE_WOL in probe.
Fixes: 7beecaf7d5 ("net: phy: at803x: improve the WOL feature")
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Viorel Suman <viorel.suman@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 988e8d90b3 ]
Use devm_regulator_get_enable_optional() instead of hand writing it. It
saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: e58f30246c ("net: phy: at803x: fix the wol setting functions")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6db541ae27 upstream.
If a login request fails, the recovery process should be protected
against parallel resets. It is a known issue that freeing and
registering CRQ's in quick succession can result in a failover CRQ from
the VIOS. Processing a failover during login recovery is dangerous for
two reasons:
1. This will result in two parallel initialization processes, this can
cause serious issues during login.
2. It is possible that the failover CRQ is received but never executed.
We get notified of a pending failover through a transport event CRQ.
The reset is not performed until a INIT CRQ request is received.
Previously, if CRQ init fails during login recovery, then the ibmvnic
irq is freed and the login process returned error. If failover_pending
is true (a transport event was received), then the ibmvnic device
would never be able to process the reset since it cannot receive the
CRQ_INIT request due to the irq being freed. This leaved the device
in a inoperable state.
Therefore, the login failure recovery process must be hardened against
these possible issues. Possible failovers (due to quick CRQ free and
init) must be avoided and any issues during re-initialization should be
dealt with instead of being propagated up the stack. This logic is
similar to that of ibmvnic_probe().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-5-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23cc5f6674 upstream.
Perform a partial reset before sending a login request if any of the
following are true:
1. If a previous request times out. This can be dangerous because the
VIOS could still receive the old login request at any point after
the timeout. Therefore, it is best to re-register the CRQ's and
sub-CRQ's before retrying.
2. If the previous request returns an error that is not described in
PAPR. PAPR provides procedures if the login returns with partial
success or aborted return codes (section L.5.1) but other values
do not have a defined procedure. Previously, these conditions
just returned error from the login function rather than trying
to resolve the issue.
This can cause further issues since most callers of the login
function are not prepared to handle an error when logging in. This
improper cleanup can lead to the device being permanently DOWN'd.
For example, if the VIOS believes that the device is already logged
in then it will return INVALID_STATE (-7). If we never re-register
CRQ's then it will always think that the device is already logged
in. This leaves the device inoperable.
The partial reset involves freeing the sub-CRQs, freeing the CRQ then
registering and initializing a new CRQ and sub-CRQs. This essentially
restarts all communication with VIOS to allow for a fresh login attempt
that will be unhindered by any previous failed attempts.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-4-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d78a671eb8 upstream.
Rather than leaving the DMA unmapping of the login buffers to the
login response handler, move this work into the login release functions.
Previously, these functions were only used for freeing the allocated
buffers. This could lead to issues if there are more than one
outstanding login buffer requests, which is possible if a login request
times out.
If a login request times out, then there is another call to send login.
The send login function makes a call to the login buffer release
function. In the past, this freed the buffers but did not DMA unmap.
Therefore, the VIOS could still write to the old login (now freed)
buffer. It is for this reason that it is a good idea to leave the DMA
unmap call to the login buffers release function.
Since the login buffer release functions now handle DMA unmapping,
remove the duplicate DMA unmapping in handle_login_rsp().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-3-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 411c565b4b upstream.
If the LOGIN CRQ fails to send then we must DMA unmap the response
buffer. Previously, if the CRQ failed then the memory was freed without
DMA unmapping.
Fixes: c98d9cc417 ("ibmvnic: send_login should check for crq errors")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-2-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db17ba719b upstream.
Ensure that all offsets in a login response buffer are within the size
of the allocated response buffer. Any offsets or lengths that surpass
the allocation are likely the result of an incomplete response buffer.
In these cases, a full reset is necessary.
When attempting to login, the ibmvnic device will allocate a response
buffer and pass a reference to the VIOS. The VIOS will then send the
ibmvnic device a LOGIN_RSP CRQ to signal that the buffer has been filled
with data. If the ibmvnic device does not get a response in 20 seconds,
the old buffer is freed and a new login request is sent. With 2
outstanding requests, any LOGIN_RSP CRQ's could be for the older
login request. If this is the case then the login response buffer (which
is for the newer login request) could be incomplete and contain invalid
data. Therefore, we must enforce strict sanity checks on the response
buffer values.
Testing has shown that the `off_rxadd_buff_size` value is filled in last
by the VIOS and will be the smoking gun for these circumstances.
Until VIOS can implement a mechanism for tracking outstanding response
buffers and a method for mapping a LOGIN_RSP CRQ to a particular login
response buffer, the best ibmvnic can do in this situation is perform a
full reset.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aab8e1a200 upstream.
Handling pci errors should fully teardown and load back auxiliary
devices, same as done through mlx5 health recovery flow.
Fixes: 72ed5d5624 ("net/mlx5: Suspend auxiliary devices only in case of PCI device suspend")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d006207625 upstream.
When device is in error state, marked by the flag
MLX5_DEVICE_STATE_INTERNAL_ERROR, the HW and PCI may not be accessible
and so clock update work should be skipped. Furthermore, such access
through PCI in error state, after calling mlx5_pci_disable_device() can
result in failing to recover from pci errors.
Fixes: ef9814deaf ("net/mlx5e: Add HW timestamping (TS) support")
Reported-and-tested-by: Ganesh G R <ganeshgr@linux.ibm.com>
Closes: https://lore.kernel.org/netdev/9bdb9b9d-140a-7a28-f0de-2e64e873c068@nvidia.com
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dc2b3922d upstream.
When querying eswitch functions 0 is a valid number of host VFs. After
introducing ARM SRIOV falling through to getting the max value from PCI
results in using the total VFs allowed on the ARM for the host.
Fixes: 86eec50bea ("net/mlx5: Support querying max VFs from device");
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e3d20617b upstream.
hns3_dbg_fill_content()/hclge_dbg_fill_content() is aim to integrate some
items to a string for content, and we add '\n' and '\0' in the last
two bytes of content.
strscpy() will add '\0' in the last byte of destination buffer(one of
items), it result in finishing content print ahead of schedule and some
dump content truncation.
One Error log shows as below:
cat mac_list/uc
UC MAC_LIST:
Expected:
UC MAC_LIST:
FUNC_ID MAC_ADDR STATE
pf 00:2b:19:05:03:00 ACTIVE
The destination buffer is length-bounded and not required to be
NUL-terminated, so just change strscpy() to memcpy() to fix it.
Fixes: 1cf3d5567f ("net: hns3: fix strncpy() not using dest-buf length as length issue")
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20230809020902.1941471-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
