commit 24e0e61db3 upstream.
In AHCI 1.3.1, the register description for CAP.SSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Slumber state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Slumber requests."
In AHCI 1.3.1, the register description for CAP.PSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Partial state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Partial requests."
Ensure that we always set the corresponding bits in PxSCTL.IPM, such that
a device is not allowed to initiate transitions to power states which are
unsupported by the HBA.
DevSleep is always initiated by the HBA, however, for completeness, set the
corresponding bit in PxSCTL.IPM such that agressive link power management
cannot transition to DevSleep if DevSleep is not supported.
sata_link_scr_lpm() is used by libahci, ata_piix and libata-pmp.
However, only libahci has the ability to read the CAP/CAP2 register to see
if these features are supported. Therefore, in order to not introduce any
regressions on ata_piix or libata-pmp, create flags that indicate that the
respective feature is NOT supported. This way, the behavior for ata_piix
and libata-pmp should remain unchanged.
This change is based on a patch originally submitted by Runa Guo-oc.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Fixes: 1152b2617a ("libata: implement sata_link_scr_lpm() and make ata_dev_set_feature() global")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 25e73b7e3f ]
It was reported that under certain circumstances GCC emits ENDBR
instructions for _THIS_IP_ usage. Specifically, when it appears at the
start of a basic block -- but not elsewhere.
Since _THIS_IP_ is never used for control flow, these ENDBR
instructions are completely superfluous. Override the _THIS_IP_
definition for x86_64 to avoid this.
Less ENDBR instructions is better.
Fixes: 156ff4a544 ("x86/ibt: Base IBT bits")
Reported-by: David Kaplan <David.Kaplan@amd.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230802110323.016197440@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d58cdfae6a ]
Add a helper to initialize a bvec based of a page pointer. This will help
removing various open code bvec initializations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20230203150634.3199647-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 1f0bbf2894 ("nvmet-tcp: pass iov_len instead of sg->length to bvec_set_page()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19d6634d87 ]
Add unlocked variant of dma_buf_map/unmap_attachment() that will
be used by drivers that don't take the reservation lock explicitly.
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221017172229.42269-3-dmitry.osipenko@collabora.com
Stable-dep-of: a2cb9cd6a3 ("misc: fastrpc: Fix incorrect DMA mapping unmap request")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12e6ac69cc ]
Some NXP processors using ChipIdea USB IP have a bug when frame babble is
detected.
Issue description:
In USB camera test, our controller is host in HS mode. In ISOC IN, when
device sends data across the micro frame, it causes the babble in host
controller. This will clear the PE bit. In spec, it also requires to set
the PEC bit and then set the PCI bit. Without the PCI interrupt, the
software does not know the PE is cleared.
This will add a flag CI_HDRC_HAS_PORTSC_PEC_MISSED to some impacted
platform datas. And the ehci host driver will assert PEC by SW when
specific conditions are satisfied.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230809024432.535160-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7ed3465da ]
When compiling with gcc 13 and CONFIG_FORTIFY_SOURCE=y, the following
warning appears:
In function ‘fortify_memcpy_chk’,
inlined from ‘size_entry_mwt’ at net/bridge/netfilter/ebtables.c:2118:2:
./include/linux/fortify-string.h:592:25: error: call to ‘__read_overflow2_field’
declared with attribute warning: detected read beyond size of field (2nd parameter);
maybe use struct_group()? [-Werror=attribute-warning]
592 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The compiler is complaining:
memcpy(&offsets[1], &entry->watchers_offset,
sizeof(offsets) - sizeof(offsets[0]));
where memcpy reads beyong &entry->watchers_offset to copy
{watchers,target,next}_offset altogether into offsets[]. Silence the
warning by wrapping these three up via struct_group().
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d11a69873d ]
Arm platforms use is_default_overflow_handler() to determine if the
hw_breakpoint code should single-step over the breakpoint trigger or
let the custom handler deal with it.
Since bpf_overflow_handler() currently isn't recognized as a default
handler, attaching a BPF program to a PERF_TYPE_BREAKPOINT event causes
it to keep firing (the instruction triggering the data abort exception
is never skipped). For example:
# bpftrace -e 'watchpoint:0x10000:4:w { print("hit") }' -c ./test
Attaching 1 probe...
hit
hit
[...]
^C
(./test performs a single 4-byte store to 0x10000)
This patch replaces the check with uses_default_overflow_handler(),
which accounts for the bpf_overflow_handler() case by also testing
if one of the perf_event_output functions gets invoked indirectly,
via orig_default_handler.
Signed-off-by: Tomislav Novak <tnovak@meta.com>
Tested-by: Samuel Gosselin <sgosselin@google.com> # arm64
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/linux-arm-kernel/20220923203644.2731604-1-tnovak@fb.com/
Link: https://lore.kernel.org/r/20230605191923.1219974-1-tnovak@meta.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0242737dc4 ]
Some HiSilicon SMMU PMCG suffers the erratum 162001900 that the PMU
disable control sometimes fail to disable the counters. This will lead
to error or inaccurate data since before we enable the counters the
counter's still counting for the event used in last perf session.
This patch tries to fix this by hardening the global disable process.
Before disable the PMU, writing an invalid event type (0xffff) to
focibly stop the counters. Correspondingly restore each events on
pmu::pmu_enable().
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20230814124012.58013-1-yangyicong@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d243b34459 ]
Under PREEMPT_RT, __put_task_struct() indirectly acquires sleeping
locks. Therefore, it can't be called from an non-preemptible context.
One practical example is splat inside inactive_task_timer(), which is
called in a interrupt context:
CPU: 1 PID: 2848 Comm: life Kdump: loaded Tainted: G W ---------
Hardware name: HP ProLiant DL388p Gen8, BIOS P70 07/15/2012
Call Trace:
dump_stack_lvl+0x57/0x7d
mark_lock_irq.cold+0x33/0xba
mark_lock+0x1e7/0x400
mark_usage+0x11d/0x140
__lock_acquire+0x30d/0x930
lock_acquire.part.0+0x9c/0x210
rt_spin_lock+0x27/0xe0
refill_obj_stock+0x3d/0x3a0
kmem_cache_free+0x357/0x560
inactive_task_timer+0x1ad/0x340
__run_hrtimer+0x8a/0x1a0
__hrtimer_run_queues+0x91/0x130
hrtimer_interrupt+0x10f/0x220
__sysvec_apic_timer_interrupt+0x7b/0xd0
sysvec_apic_timer_interrupt+0x4f/0xd0
asm_sysvec_apic_timer_interrupt+0x12/0x20
RIP: 0033:0x7fff196bf6f5
Instead of calling __put_task_struct() directly, we defer it using
call_rcu(). A more natural approach would use a workqueue, but since
in PREEMPT_RT, we can't allocate dynamic memory from atomic context,
the code would become more complex because we would need to put the
work_struct instance in the task_struct and initialize it when we
allocate a new task_struct.
The issue is reproducible with stress-ng:
while true; do
stress-ng --sched deadline --sched-period 1000000000 \
--sched-runtime 800000000 --sched-deadline \
1000000000 --mmapfork 23 -t 20
done
Reported-by: Hu Chunyu <chuhu@redhat.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Valentin Schneider <vschneid@redhat.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230614122323.37957-2-wander@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa99e5f87b ]
Andrei Vagin reported bind() regression with strace logs.
If we bind() a TCPv6 socket to ::FFFF:0.0.0.0 and then bind() a TCPv4
socket to 127.0.0.1, the 2nd bind() should fail but now succeeds.
from socket import *
s1 = socket(AF_INET6, SOCK_STREAM)
s1.bind(('::ffff:0.0.0.0', 0))
s2 = socket(AF_INET, SOCK_STREAM)
s2.bind(('127.0.0.1', s1.getsockname()[1]))
During the 2nd bind(), if tb->family is AF_INET6 and sk->sk_family is
AF_INET in inet_bind2_bucket_match_addr_any(), we still need to check
if tb has the v4-mapped-v6 wildcard address.
The example above does not work after commit 5456262d2b ("net: Fix
incorrect address comparison when searching for a bind2 bucket"), but
the blamed change is not the commit.
Before the commit, the leading zeros of ::FFFF:0.0.0.0 were treated
as 0.0.0.0, and the sequence above worked by chance. Technically, this
case has been broken since bhash2 was introduced.
Note that if we bind() two sockets to 127.0.0.1 and then ::FFFF:0.0.0.0,
the 2nd bind() fails properly because we fall back to using bhash to
detect conflicts for the v4-mapped-v6 address.
Fixes: 28044fc1d4 ("net: Add a bhash2 table hashed by port and address")
Reported-by: Andrei Vagin <avagin@google.com>
Closes: https://lore.kernel.org/netdev/ZPuYBOFC8zsK6r9T@google.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cdc3223e7 ]
Some code defines the IPv6 wildcard address as a local variable and
use it with memcmp() or ipv6_addr_equal().
Let's use in6addr_any and ipv6_addr_any() instead.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aa99e5f87b ("tcp: Fix bind() regression for v4-mapped-v6 wildcard address.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cdd9f1aae ]
ip6_sock_set_addr_preferences() second argument should be an integer.
SUNRPC attempts to set IPV6_PREFER_SRC_PUBLIC were
translated to IPV6_PREFER_SRC_TMP
Fixes: 18d5ad6232 ("ipv6: add ip6_sock_set_addr_preferences")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230911154213.713941-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 271de525e1 ]
The commit 64696c40d0 ("bpf: Add __bpf_prog_{enter,exit}_struct_ops for struct_ops trampoline")
removed prog->active check for struct_ops prog. The bpf_lsm
and bpf_iter is also using trampoline. Like struct_ops, the bpf_lsm
and bpf_iter have fixed hooks for the prog to attach. The
kernel does not call the same hook in a recursive way.
This patch also removes the prog->active check for
bpf_lsm and bpf_iter.
A later patch has a test to reproduce the recursion issue
for a sleepable bpf_lsm program.
This patch appends the '_recur' naming to the existing
enter and exit functions that track the prog->active counter.
New __bpf_prog_{enter,exit}[_sleepable] function are
added to skip the prog->active tracking. The '_struct_ops'
version is also removed.
It also moves the decision on picking the enter and exit function to
the new bpf_trampoline_{enter,exit}(). It returns the '_recur' ones
for all tracing progs to use. For bpf_lsm, bpf_iter,
struct_ops (no prog->active tracking after 64696c40d0), and
bpf_lsm_cgroup (no prog->active tracking after 69fd337a97),
it will return the functions that don't track the prog->active.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20221025184524.3526117-2-martin.lau@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 7645629f7d ("bpf: Invoke __bpf_prog_exit_sleepable_recur() on recursion in kern_sys_bpf().")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 719c5e37e9 ]
Previously, the defines for phy_device flags in the Micrel driver were
ambiguous in their representation. They were intended to be bit masks
but were mistakenly defined as bit positions. This led to the following
issues:
- MICREL_KSZ8_P1_ERRATA, designated for KSZ88xx switches, overlapped
with MICREL_PHY_FXEN and MICREL_PHY_50MHZ_CLK.
- Due to this overlap, the code path for MICREL_PHY_FXEN, tailored for
the KSZ8041 PHY, was not executed for KSZ88xx PHYs.
- Similarly, the code associated with MICREL_PHY_50MHZ_CLK wasn't
triggered for KSZ88xx.
To rectify this, all three flags have now been explicitly converted to
use the `BIT()` macro, ensuring they are defined as bit masks and
preventing potential overlaps in the future.
Fixes: 49011e0c15 ("net: phy: micrel: ksz886x/ksz8081: add cabletest support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8423be8926 ]
Route hints when the nexthop is part of a multipath group causes packets
in the same receive batch to be sent to the same nexthop irrespective of
the multipath hash of the packet. So, do not extract route hint for
packets whose destination is part of a multipath group.
A new SKB flag IP6SKB_MULTIPATH is introduced for this purpose, set the
flag when route is looked up in fib6_select_path() and use it in
ip6_can_use_hint() to check for the existence of the flag.
Fixes: 197dbf24e3 ("ipv6: introduce and uses route look hints for list input.")
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ac66cb03a ]
Route hints when the nexthop is part of a multipath group causes packets
in the same receive batch to be sent to the same nexthop irrespective of
the multipath hash of the packet. So, do not extract route hint for
packets whose destination is part of a multipath group.
A new SKB flag IPSKB_MULTIPATH is introduced for this purpose, set the
flag when route is looked up in ip_mkroute_input() and use it in
ip_extract_route_hint() to check for the existence of the flag.
Fixes: 02b2494161 ("ipv4: use dst hint for ipv4 list receive")
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e6300e7b3 ]
Every time sk->sk_forward_alloc is read locklessly,
add a READ_ONCE().
Add sk_forward_alloc_add() helper to centralize updates,
to reduce number of WRITE_ONCE().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aae7625ff ]
New skbs allocated via nf_send_reset() have skb->dev == NULL.
fib*_rules_early_flow_dissect helpers already have a 'struct net'
argument but its not passed down to the flow dissector core, which
will then WARN as it can't derive a net namespace to use:
WARNING: CPU: 0 PID: 0 at net/core/flow_dissector.c:1016 __skb_flow_dissect+0xa91/0x1cd0
[..]
ip_route_me_harder+0x143/0x330
nf_send_reset+0x17c/0x2d0 [nf_reject_ipv4]
nft_reject_inet_eval+0xa9/0xf2 [nft_reject_inet]
nft_do_chain+0x198/0x5d0 [nf_tables]
nft_do_chain_inet+0xa4/0x110 [nf_tables]
nf_hook_slow+0x41/0xc0
ip_local_deliver+0xce/0x110
..
Cc: Stanislav Fomichev <sdf@google.com>
Cc: David Ahern <dsahern@kernel.org>
Cc: Ido Schimmel <idosch@nvidia.com>
Fixes: 812fa71f0d ("netfilter: Dissect flow after packet mangling")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217826
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230830110043.30497-1-fw@strlen.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 687fe7dfb7 ]
Remove option having i2c client contain raw gpio number instead of proper
IRQ number. There are no users of this facility in mainline and it will
allow cleaning up the driver code with regard to wakeup handling, etc.
Link: https://lore.kernel.org/r/20230724053024.352054-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: cc141c35af ("Input: tca6416-keypad - fix interrupt enable disbalance")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 115f1a5c42 upstream.
We have many places using this expression:
SKB_DATA_ALIGN(sizeof(struct skb_shared_info))
Use of SKB_HEAD_ALIGN() will allow to clean them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[Ajay: Regenerated the patch for v6.1.y]
Signed-off-by: Ajay Kaher <akaher@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6df1b22129 upstream.
lru_gen_folio will be chained into per-node lists by the coming
lrugen->list.
Link: https://lkml.kernel.org/r/20221222041905.2431096-3-yuzhao@google.com
Signed-off-by: Yu Zhao <yuzhao@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Larabel <Michael@MichaelLarabel.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cf9d015be upstream.
After commit c28cd1f343 ("clk: Mark a fwnode as initialized when using
CLK_OF_DECLARE() macro"), drivers/clk/mvebu/kirkwood.c fails to build:
drivers/clk/mvebu/kirkwood.c:358:1: error: expected identifier or '('
CLK_OF_DECLARE(98dx1135_clk, "marvell,mv98dx1135-core-clock",
^
include/linux/clk-provider.h:1367:21: note: expanded from macro 'CLK_OF_DECLARE'
static void __init name##_of_clk_init_declare(struct device_node *np) \
^
<scratch space>:124:1: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
drivers/clk/mvebu/kirkwood.c:358:1: error: invalid digit 'd' in decimal constant
include/linux/clk-provider.h:1372:34: note: expanded from macro 'CLK_OF_DECLARE'
OF_DECLARE_1(clk, name, compat, name##_of_clk_init_declare)
^
<scratch space>:125:3: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
drivers/clk/mvebu/kirkwood.c:358:1: error: invalid digit 'd' in decimal constant
include/linux/clk-provider.h:1372:34: note: expanded from macro 'CLK_OF_DECLARE'
OF_DECLARE_1(clk, name, compat, name##_of_clk_init_declare)
^
<scratch space>:125:3: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
drivers/clk/mvebu/kirkwood.c:358:1: error: invalid digit 'd' in decimal constant
include/linux/clk-provider.h:1372:34: note: expanded from macro 'CLK_OF_DECLARE'
OF_DECLARE_1(clk, name, compat, name##_of_clk_init_declare)
^
<scratch space>:125:3: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
C function names must start with either an alphabetic letter or an
underscore. To avoid generating invalid function names from clock names,
add two underscores to the beginning of the identifier.
Fixes: c28cd1f343 ("clk: Mark a fwnode as initialized when using CLK_OF_DECLARE() macro")
Suggested-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230308-clk_of_declare-fix-v1-1-317b741e2532@kernel.org
Reviewed-by: Saravana Kannan <saravanak@google.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c28cd1f343 upstream.
We already mark fwnodes as initialized when they are registered as clock
providers. We do this so that fw_devlink can tell when a clock driver
doesn't use the driver core framework to probe/initialize its device.
This ensures fw_devlink doesn't block the consumers of such a clock
provider indefinitely.
However, some users of CLK_OF_DECLARE() macros don't use the same node
that matches the macro as the node for the clock provider, but they
initialize the entire node. To cover these cases, also mark the nodes
that match the macros as initialized when the init callback function is
called.
An example of this is "stericsson,u8500-clks" that's handled using
CLK_OF_DECLARE() and looks something like this:
clocks {
compatible = "stericsson,u8500-clks";
prcmu_clk: prcmu-clock {
#clock-cells = <1>;
};
prcc_pclk: prcc-periph-clock {
#clock-cells = <2>;
};
prcc_kclk: prcc-kernel-clock {
#clock-cells = <2>;
};
prcc_reset: prcc-reset-controller {
#reset-cells = <2>;
};
...
};
This patch makes sure that "clocks" is marked as initialized so that
fw_devlink knows that all nodes under it have been initialized. If the
driver creates struct devices for some of the subnodes, fw_devlink is
smart enough to know to wait for those devices to probe, so no special
handling is required for those cases.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/lkml/CACRpkdamxDX6EBVjKX5=D3rkHp17f5pwGdBVhzFU90-0MHY6dQ@mail.gmail.com/
Fixes: 4a032827da ("of: property: Simplify of_link_to_phandle()")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20230302014639.297514-1-saravanak@google.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f236433064 upstream.
Some usb hubs will negotiate DisplayPort Alt mode with the device
but will then negotiate a data role swap after entering the alt
mode. The data role swap causes the device to unregister all alt
modes, however the usb hub will still send Attention messages
even after failing to reregister the Alt Mode. type_altmode_attention
currently does not verify whether or not a device's altmode partner
exists, which results in a NULL pointer error when dereferencing
the typec_altmode and typec_altmode_ops belonging to the altmode
partner.
Verify the presence of a device's altmode partner before sending
the Attention message to the Alt Mode driver.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230814180559.923475-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cd474e573 upstream.
Interrupts are blocked in SDEI context, per the SDEI spec: "The client
interrupts cannot preempt the event handler." If we crashed in the SDEI
handler-running context (as with ACPI's AGDI) then we need to clean up the
SDEI state before proceeding to the crash kernel so that the crash kernel
can have working interrupts.
Track the active SDEI handler per-cpu so that we can COMPLETE_AND_RESUME
the handler, discarding the interrupted context.
Fixes: f5df269618 ("arm64: kernel: Add arch-specific SDEI entry code and CPU masking")
Signed-off-by: D Scott Phillips <scott@os.amperecomputing.com>
Cc: stable@vger.kernel.org
Reviewed-by: James Morse <james.morse@arm.com>
Tested-by: Mihai Carabas <mihai.carabas@oracle.com>
Link: https://lore.kernel.org/r/20230627002939.2758-1-scott@os.amperecomputing.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4f39c9f14 upstream.
The goal is to support a bpf_redirect() from an ethernet device (ingress)
to a ppp device (egress).
The l2 header is added automatically by the ppp driver, thus the ethernet
header should be removed.
CC: stable@vger.kernel.org
Fixes: 27b29f6305 ("bpf: add bpf_redirect() helper")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Siwar Zitouni <siwar.zitouni@6wind.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 62ec209209 ]
Change scsi_host_lookup() hostnum argument type from unsigned short to
unsigned int to match the type used everywhere else.
Fixes: 6d49f63b41 ("[SCSI] Make host_no an unsigned int")
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Link: https://lore.kernel.org/r/a02497e7-c12b-ef15-47fc-3f0a0b00ffce@cybernetics.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 276e14e6c3 ]
Some digitizers (notably XP-Pen Artist 24) do not report the Invert
usage when erasing. This causes the device to be permanently stuck with
the BTN_TOOL_RUBBER tool after sending Eraser, as Invert is the only
usage that can release the tool. In this state, Touch and Inrange are
no longer reported to userspace, rendering the pen unusable.
Prior to commit 87562fcd13 ("HID: input: remove the need for
HID_QUIRK_INVERT"), BTN_TOOL_RUBBER was never set and Eraser events were
simply translated into BTN_TOUCH without causing an inconsistent state.
Introduce HID_QUIRK_NOINVERT for such digitizers and detect them during
hidinput_configure_usage(). This quirk causes the tool to be released
as soon as Eraser is reported as not set. Set BTN_TOOL_RUBBER in
input->keybit when mapping Eraser.
Fixes: 87562fcd13 ("HID: input: remove the need for HID_QUIRK_INVERT")
Co-developed-by: Nils Fuhler <nils@nilsfuhler.de>
Signed-off-by: Nils Fuhler <nils@nilsfuhler.de>
Signed-off-by: Illia Ostapyshyn <ostapyshyn@sra.uni-hannover.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 948a77aaec ]
The adap_configured() callback was called with the adap->lock mutex
held if the 'configured' argument was false, and without the adap->lock
mutex held if that argument was true.
That was very confusing, and so split this up in a adap_unconfigured()
callback and a high-level configured() callback.
This also makes it easier to understand when the mutex is held: all
low-level adap_* callbacks are called with the mutex held. All other
callbacks are called without that mutex held.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: f1b5716430 ("media: cec: add optional adap_configured callback")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da53c36ddd ]
A potential deadlock was found by Zheng Zhang with a local syzkaller
instance.
The problem is that when a non-blocking CEC transmit is canceled by calling
cec_data_cancel, that in turn can call the high-level received() driver
callback, which can call cec_transmit_msg() to transmit a new message.
The cec_data_cancel() function is called with the adap->lock mutex held,
and cec_transmit_msg() tries to take that same lock.
The root cause is that the received() callback can either be used to pass
on a received message (and then adap->lock is not held), or to report a
canceled transmit (and then adap->lock is held).
This is confusing, so create a new low-level adap_nb_transmit_canceled
callback that reports back that a non-blocking transmit was canceled.
And the received() callback is only called when a message is received,
as was the case before commit f9d0ecbf56 ("media: cec: correctly pass
on reply results") complicated matters.
Reported-by: Zheng Zhang <zheng.zhang@email.ucr.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: f9d0ecbf56 ("media: cec: correctly pass on reply results")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79038a9944 ]
In some randconfig builds, kernfs ends up being disabled, so there is no prototype
for kernfs_generic_poll()
In file included from kernel/sched/build_utility.c:97:
kernel/sched/psi.c:1479:3: error: implicit declaration of function 'kernfs_generic_poll' is invalid in C99 [-Werror,-Wimplicit-function-declaration]
kernfs_generic_poll(t->of, wait);
^
Add a stub helper for it, as we have it for other kernfs functions.
Fixes: aff037078e ("sched/psi: use kernfs polling functions for PSI trigger polling")
Fixes: 147e1a97c4 ("fs: kernfs: add poll file operation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chengming Zhou <zhouchengming@bytedance.com>
Link: https://lore.kernel.org/r/20230724121823.1357562-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05d56d8079 ]
Fixes the warning:
include/uapi/linux/sync_file.h:77: warning: Function parameter or member 'num_fences' not described in 'sync_file_info'
Fixes: 2d75c88fef ("staging/android: refactor SYNC IOCTLs")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20230724145000.125880-1-robdclark@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbd2a05f29 ]
Instead of using a tiny, static scratch buffer, we should use a kmalloc()-ed
buffer that is allocated when checking for read plus usage. This lets us
use the buffer before decoding any part of the READ_PLUS operation
instead of setting it right before segment decoding, meaning it should
be a little more robust.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Stable-dep-of: bb05a617f0 ("NFSv4.2: Fix READ_PLUS smatch warnings")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e70d0acf0 ]
Many places in the kernel write the Link Control and Root Control PCI
Express Capability Registers without proper concurrency control and this
could result in losing the changes one of the writers intended to make.
Add pcie_cap_lock spinlock into the struct pci_dev and use it to protect
bit changes made in the RMW capability accessors. Protect only a selected
set of registers by differentiating the RMW accessor internally to
locked/unlocked variants using a wrapper which has the same signature as
pcie_capability_clear_and_set_word(). As the Capability Register (pos)
given to the wrapper is always a constant, the compiler should be able to
simplify all the dead-code away.
So far only the Link Control Register (ASPM, hotplug, link retraining,
various drivers) and the Root Control Register (AER & PME) seem to
require RMW locking.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: c7f486567c ("PCI PM: PCIe PME root port service driver")
Fixes: f12eb72a26 ("PCI/ASPM: Use PCI Express Capability accessors")
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Fixes: affa48de84 ("staging/rdma/hfi1: Add support for enabling/disabling PCIe ASPM")
Fixes: 849a9366cb ("misc: rtsx: Add support new chip rts5228 mmc: rtsx: Add support MMC_CAP2_NO_MMC")
Fixes: 3d1e7aa80d ("misc: rtsx: Use pcie_capability_clear_and_set_word() for PCI_EXP_LNKCTL")
Fixes: c0e5f4e73a ("misc: rtsx: Add support for RTS5261")
Fixes: 3df4fce739 ("misc: rtsx: separate aspm mode into MODE_REG and MODE_CFG")
Fixes: 121e9c6b5c ("misc: rtsx: modify and fix init_hw function")
Fixes: 19f3bd548f ("mfd: rtsx: Remove LCTLR defination")
Fixes: 773ccdfd9c ("mfd: rtsx: Read vendor setting from config space")
Fixes: 8275b77a15 ("mfd: rts5249: Add support for RTS5250S power saving")
Fixes: 5da4e04ae4 ("misc: rtsx: Add support for RTS5260")
Fixes: 0f49bfbd0f ("tg3: Use PCI Express Capability accessors")
Fixes: 5e7dfd0fb9 ("tg3: Prevent corruption at 10 / 100Mbps w CLKREQ")
Fixes: b726e493e8 ("r8169: sync existing 8168 device hardware start sequences with vendor driver")
Fixes: e6de30d63e ("r8169: more 8168dp support.")
Fixes: 8a06127602 ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards")
Fixes: 6f461f6c7c ("e1000e: enable/disable ASPM L0s and L1 and ERT according to hardware errata")
Fixes: 1eae4eb2a1 ("e1000e: Disable L1 ASPM power savings for 82573 mobile variants")
Fixes: 8060e169e0 ("ath9k: Enable extended synch for AR9485 to fix L0s recovery issue")
Fixes: 69ce674bfa ("ath9k: do btcoex ASPM disabling at initialization time")
Fixes: f37f055035 ("mt76: mt76x2e: disable pcie_aspm by default")
Link: https://lore.kernel.org/r/20230717120503.15276-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 278294798a ]
PCI config space access from user space has traditionally been
unrestricted with writes being an understood risk for device operation.
Unfortunately, device breakage or odd behavior from config writes lacks
indicators that can leave driver writers confused when evaluating
failures. This is especially true with the new PCIe Data Object
Exchange (DOE) mailbox protocol where backdoor shenanigans from user
space through things such as vendor defined protocols may affect device
operation without complete breakage.
A prior proposal restricted read and writes completely.[1] Greg and
Bjorn pointed out that proposal is flawed for a couple of reasons.
First, lspci should always be allowed and should not interfere with any
device operation. Second, setpci is a valuable tool that is sometimes
necessary and it should not be completely restricted.[2] Finally
methods exist for full lock of device access if required.
Even though access should not be restricted it would be nice for driver
writers to be able to flag critical parts of the config space such that
interference from user space can be detected.
Introduce pci_request_config_region_exclusive() to mark exclusive config
regions. Such regions trigger a warning and kernel taint if accessed
via user space.
Create pci_warn_once() to restrict the user from spamming the log.
[1] https://lore.kernel.org/all/161663543465.1867664.5674061943008380442.stgit@dwillia2-desk3.amr.corp.intel.com/
[2] https://lore.kernel.org/all/YF8NGeGv9vYcMfTV@kroah.com/
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20220926215711.2893286-2-ira.weiny@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Stable-dep-of: 5e70d0acf0 ("PCI: Add locking to RMW PCI Express Capability Register accessors")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eba4db02a ]
There are 10 more GDSCs that we've not been caring about, and by extension
(and perhaps even more importantly), not putting to sleep. Add them.
Fixes: a66a82f2a5 ("dt-bindings: clock: Add Qualcomm SC8280XP GCC bindings")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230620-topic-sc8280_gccgdsc-v2-2-562c1428c10d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43c9835b14 ]
Currently the write_cache attribute allows enabling the QUEUE_FLAG_WC
flag on devices that never claimed the capability.
Fix that by adding a QUEUE_FLAG_HW_WC flag that is set by
blk_queue_write_cache and guards re-enabling the cache through sysfs.
Note that any rescan that calls blk_queue_write_cache will still
re-enable the write cache as in the current code.
Fixes: 93e9d8e836 ("block: add ability to flag write back caching on a device")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230707094239.107968-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7a2ef0c4b ]
While looking at a bug, I got rather confused by the layout of the
'status' field in ieee80211_tx_info. Apparently, the intention is that
status_driver_data[] is used for driver specific data, and fills up the
size of the union to 40 bytes, just like the other ones.
This is indeed what actually happens, but only because of the
combination of two mistakes:
- "void *status_driver_data[18 / sizeof(void *)];" is intended
to be 18 bytes long but is actually two bytes shorter because of
rounding-down in the division, to a multiple of the pointer
size (4 bytes or 8 bytes).
- The other fields combined are intended to be 22 bytes long, but
are actually 24 bytes because of padding in front of the
unaligned tx_time member, and in front of the pointer array.
The two mistakes cancel out. so the size ends up fine, but it seems
more helpful to make this explicit, by having a multiple of 8 bytes
in the size calculation and explicitly describing the padding.
Fixes: ea5907db2a ("mac80211: fix struct ieee80211_tx_info size")
Fixes: 02219b3abc ("mac80211: add WMM admission control support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230623152443.2296825-2-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a171fbec88 ]
LWTUNNEL_XMIT_CONTINUE is implicitly assumed in ip(6)_finish_output2,
such that any positive return value from a xmit hook could cause
unexpected continue behavior, despite that related skb may have been
freed. This could be error-prone for future xmit hook ops. One of the
possible errors is to return statuses of dst_output directly.
To make the code safer, redefine LWTUNNEL_XMIT_CONTINUE value to
distinguish from dst_output statuses and check the continue
condition explicitly.
Fixes: 3a0af8fd61 ("bpf: BPF for lightweight tunnel infrastructure")
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/96b939b85eda00e8df4f7c080f770970a4c5f698.1692326837.git.yan@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac8a529621 ]
Now there are two indicators of socket memory pressure sit inside
struct mem_cgroup, socket_pressure and tcpmem_pressure, indicating
memory reclaim pressure in memcg->memory and ->tcpmem respectively.
When in legacy mode (cgroupv1), the socket memory is charged into
->tcpmem which is independent of ->memory, so socket_pressure has
nothing to do with socket's pressure at all. Things could be worse
by taking socket_pressure into consideration in legacy mode, as a
pressure in ->memory can lead to premature reclamation/throttling
in socket.
While for the default mode (cgroupv2), the socket memory is charged
into ->memory, and ->tcpmem/->tcpmem_pressure are simply not used.
So {socket,tcpmem}_pressure are only used in default/legacy mode
respectively for indicating socket memory pressure. This patch fixes
the pieces of code that make mixed use of both.
Fixes: 8e8ae64524 ("mm: memcontrol: hook up vmpressure to socket pressure")
Signed-off-by: Abel Wu <wuyun.abel@bytedance.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ae4577bc0 ]
The function crypto_drop_spawn expects to be called in process
context. However, when an instance is unregistered while it still
has active users, the last user may cause the instance to be freed
in atomic context.
Fix this by delaying the freeing to a work queue.
Fixes: 6bfd48096f ("[CRYPTO] api: Added spawns")
Reported-by: Florent Revest <revest@chromium.org>
Reported-by: syzbot+d769eed29cc42d75e2a3@syzkaller.appspotmail.com
Reported-by: syzbot+610ec0671f51e838436e@syzkaller.appspotmail.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Florent Revest <revest@chromium.org>
Acked-by: Florent Revest <revest@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5125e757e6 ]
To avoid returning uninitialized or random values when querying the file
descriptor (fd) and accessing probe_addr, it is necessary to clear the
variable prior to its use.
Fixes: 41bdc4b40e ("bpf: introduce bpf subcommand BPF_TASK_FD_QUERY")
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20230709025630.3735-6-laoar.shao@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1ed39ec11 ]
load_nls() take a char * parameter, use it to find nls module in list or
construct the module name to load it.
This change make load_nls() take a const parameter, so we don't need do
some cast like this:
ses->local_nls = load_nls((char *)ctx->local_nls->charset);
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Winston Wen <wentao@uniontech.com>
Reviewed-by: Paulo Alcantara <pc@manguebit.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae440c5da3 ]
Some drivers firmwares parse by themselves slice header and need
num_delta_pocs_of_ref_rps_idx value to parse slice header
short_term_ref_pic_set().
Use one of the 4 reserved bytes to store this value without
changing the v4l2_ctrl_hevc_decode_params structure size and padding.
This value also exist in DXVA API.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: fix typo in num_delta_pocs_of_ref_rps_idx doc]
Stable-dep-of: 297160d411 ("media: mediatek: vcodec: move core context from device to each instance")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2abcc4b5a6 upstream.
module_init_layout_section() choses whether the core module loader
considers a section as init or not. This affects the placement of the
exit section when module unloading is disabled. This code will never run,
so it can be free()d once the module has been initialised.
arm and arm64 need to count the number of PLTs they need before applying
relocations based on the section name. The init PLTs are stored separately
so they can be free()d. arm and arm64 both use within_module_init() to
decide which list of PLTs to use when applying the relocation.
Because within_module_init()'s behaviour changes when module unloading
is disabled, both architecture would need to take this into account when
counting the PLTs.
Today neither architecture does this, meaning when module unloading is
disabled there are insufficient PLTs in the init section to load some
modules, resulting in warnings:
| WARNING: CPU: 2 PID: 51 at arch/arm64/kernel/module-plts.c:99 module_emit_plt_entry+0x184/0x1cc
| Modules linked in: crct10dif_common
| CPU: 2 PID: 51 Comm: modprobe Not tainted 6.5.0-rc4-yocto-standard-dirty #15208
| Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
| pstate: 20400005 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : module_emit_plt_entry+0x184/0x1cc
| lr : module_emit_plt_entry+0x94/0x1cc
| sp : ffffffc0803bba60
[...]
| Call trace:
| module_emit_plt_entry+0x184/0x1cc
| apply_relocate_add+0x2bc/0x8e4
| load_module+0xe34/0x1bd4
| init_module_from_file+0x84/0xc0
| __arm64_sys_finit_module+0x1b8/0x27c
| invoke_syscall.constprop.0+0x5c/0x104
| do_el0_svc+0x58/0x160
| el0_svc+0x38/0x110
| el0t_64_sync_handler+0xc0/0xc4
| el0t_64_sync+0x190/0x194
Instead of duplicating module_init_layout_section()s logic, expose it.
Reported-by: Adam Johnston <adam.johnston@arm.com>
Fixes: 055f23b74b ("module: check for exit sections in layout_sections() instead of module_init_section()")
Cc: stable@vger.kernel.org
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
