commit c1ae1c59c8 upstream.
Since the fixed commits both zdev->iommu_bitmap and zdev->lazy_bitmap
are allocated as vzalloc(zdev->iommu_pages / 8). The problem is that
zdev->iommu_bitmap is a pointer to unsigned long but the above only
yields an allocation that is a multiple of sizeof(unsigned long) which
is 8 on s390x if the number of IOMMU pages is a multiple of 64.
This in turn is the case only if the effective IOMMU aperture is
a multiple of 64 * 4K = 256K. This is usually the case and so didn't
cause visible issues since both the virt_to_phys(high_memory) reduced
limit and hardware limits use nice numbers.
Under KVM, and in particular with QEMU limiting the IOMMU aperture to
the vfio DMA limit (default 65535), it is possible for the reported
aperture not to be a multiple of 256K however. In this case we end up
with an iommu_bitmap whose allocation is not a multiple of
8 causing bitmap operations to access it out of bounds.
Sadly we can't just fix this in the obvious way and use bitmap_zalloc()
because for large RAM systems (tested on 8 TiB) the zdev->iommu_bitmap
grows too large for kmalloc(). So add our own bitmap_vzalloc() wrapper.
This might be a candidate for common code, but this area of code will
be replaced by the upcoming conversion to use the common code DMA API on
s390 so just add a local routine.
Fixes: 2245932155 ("s390/pci: use virtual memory for iommu bitmap")
Fixes: 13954fd691 ("s390/pci_dma: improve lazy flush for unmap")
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0df9dab891 upstream.
Stop zapping invalidate TDP MMU roots via work queue now that KVM
preserves TDP MMU roots until they are explicitly invalidated. Zapping
roots asynchronously was effectively a workaround to avoid stalling a vCPU
for an extended during if a vCPU unloaded a root, which at the time
happened whenever the guest toggled CR0.WP (a frequent operation for some
guest kernels).
While a clever hack, zapping roots via an unbound worker had subtle,
unintended consequences on host scheduling, especially when zapping
multiple roots, e.g. as part of a memslot. Because the work of zapping a
root is no longer bound to the task that initiated the zap, things like
the CPU affinity and priority of the original task get lost. Losing the
affinity and priority can be especially problematic if unbound workqueues
aren't affined to a small number of CPUs, as zapping multiple roots can
cause KVM to heavily utilize the majority of CPUs in the system, *beyond*
the CPUs KVM is already using to run vCPUs.
When deleting a memslot via KVM_SET_USER_MEMORY_REGION, the async root
zap can result in KVM occupying all logical CPUs for ~8ms, and result in
high priority tasks not being scheduled in in a timely manner. In v5.15,
which doesn't preserve unloaded roots, the issues were even more noticeable
as KVM would zap roots more frequently and could occupy all CPUs for 50ms+.
Consuming all CPUs for an extended duration can lead to significant jitter
throughout the system, e.g. on ChromeOS with virtio-gpu, deleting memslots
is a semi-frequent operation as memslots are deleted and recreated with
different host virtual addresses to react to host GPU drivers allocating
and freeing GPU blobs. On ChromeOS, the jitter manifests as audio blips
during games due to the audio server's tasks not getting scheduled in
promptly, despite the tasks having a high realtime priority.
Deleting memslots isn't exactly a fast path and should be avoided when
possible, and ChromeOS is working towards utilizing MAP_FIXED to avoid the
memslot shenanigans, but KVM is squarely in the wrong. Not to mention
that removing the async zapping eliminates a non-trivial amount of
complexity.
Note, one of the subtle behaviors hidden behind the async zapping is that
KVM would zap invalidated roots only once (ignoring partial zaps from
things like mmu_notifier events). Preserve this behavior by adding a flag
to identify roots that are scheduled to be zapped versus roots that have
already been zapped but not yet freed.
Add a comment calling out why kvm_tdp_mmu_invalidate_all_roots() can
encounter invalid roots, as it's not at all obvious why zapping
invalidated roots shouldn't simply zap all invalid roots.
Reported-by: Pattara Teerapong <pteerapong@google.com>
Cc: David Stevens <stevensd@google.com>
Cc: Yiwei Zhang<zzyiwei@google.com>
Cc: Paul Hsia <paulhsia@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230916003916.2545000-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Tested-by: David Matlack <dmatlack@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ad37b5e30 ]
On mapphone devices we may get lots of noise on the micro-USB port in debug
uart mode until the phy-cpcap-usb driver probes. Let's limit the noise by
using overrun-throttle-ms.
Note that there is also a related separate issue where the charger cable
connected may cause random sysrq requests until phy-cpcap-usb probes that
still remains.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3fdc6087df upstream.
svm_leave_nested() similar to a nested VM exit, get the vCPU out of nested
mode and thus should end the local inhibition of AVIC on this vCPU.
Failure to do so, can lead to hangs on guest reboot.
Raise the KVM_REQ_APICV_UPDATE request to refresh the AVIC state of the
current vCPU in this case.
Fixes: f44509f849 ("KVM: x86: SVM: allow AVIC to co-exist with a nested guest running")
Cc: stable@vger.kernel.org
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230928173354.217464-4-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dcf37abf9 upstream.
In later revisions of AMD's APM, there is a new 'incomplete IPI' exit code:
"Invalid IPI Vector - The vector for the specified IPI was set to an
illegal value (VEC < 16)"
Note that tests on Zen2 machine show that this VM exit doesn't happen and
instead AVIC just does nothing.
Add support for this exit code by doing nothing, instead of filling
the kernel log with errors.
Also replace an unthrottled 'pr_err()' if another unknown incomplete
IPI exit happens with vcpu_unimpl()
(e.g in case AMD adds yet another 'Invalid IPI' exit reason)
Cc: <stable@vger.kernel.org>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230928173354.217464-3-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8647c52e95 upstream.
Mask off xfeatures that aren't exposed to the guest only when saving guest
state via KVM_GET_XSAVE{2} instead of modifying user_xfeatures directly.
Preserving the maximal set of xfeatures in user_xfeatures restores KVM's
ABI for KVM_SET_XSAVE, which prior to commit ad856280dd ("x86/kvm/fpu:
Limit guest user_xfeatures to supported bits of XCR0") allowed userspace
to load xfeatures that are supported by the host, irrespective of what
xfeatures are exposed to the guest.
There is no known use case where userspace *intentionally* loads xfeatures
that aren't exposed to the guest, but the bug fixed by commit ad856280dd
was specifically that KVM_GET_SAVE{2} would save xfeatures that weren't
exposed to the guest, e.g. would lead to userspace unintentionally loading
guest-unsupported xfeatures when live migrating a VM.
Restricting KVM_SET_XSAVE to guest-supported xfeatures is especially
problematic for QEMU-based setups, as QEMU has a bug where instead of
terminating the VM if KVM_SET_XSAVE fails, QEMU instead simply stops
loading guest state, i.e. resumes the guest after live migration with
incomplete guest state, and ultimately results in guest data corruption.
Note, letting userspace restore all host-supported xfeatures does not fix
setups where a VM is migrated from a host *without* commit ad856280dd,
to a target with a subset of host-supported xfeatures. However there is
no way to safely address that scenario, e.g. KVM could silently drop the
unsupported features, but that would be a clear violation of KVM's ABI and
so would require userspace to opt-in, at which point userspace could
simply be updated to sanitize the to-be-loaded XSAVE state.
Reported-by: Tyler Stachecki <stachecki.tyler@gmail.com>
Closes: https://lore.kernel.org/all/20230914010003.358162-1-tstachecki@bloomberg.net
Fixes: ad856280dd ("x86/kvm/fpu: Limit guest user_xfeatures to supported bits of XCR0")
Cc: stable@vger.kernel.org
Cc: Leonardo Bras <leobras@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Message-Id: <20230928001956.924301-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18164f66e6 upstream.
Plumb an xfeatures mask into __copy_xstate_to_uabi_buf() so that KVM can
constrain which xfeatures are saved into the userspace buffer without
having to modify the user_xfeatures field in KVM's guest_fpu state.
KVM's ABI for KVM_GET_XSAVE{2} is that features that are not exposed to
guest must not show up in the effective xstate_bv field of the buffer.
Saving only the guest-supported xfeatures allows userspace to load the
saved state on a different host with a fewer xfeatures, so long as the
target host supports the xfeatures that are exposed to the guest.
KVM currently sets user_xfeatures directly to restrict KVM_GET_XSAVE{2} to
the set of guest-supported xfeatures, but doing so broke KVM's historical
ABI for KVM_SET_XSAVE, which allows userspace to load any xfeatures that
are supported by the *host*.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230928001956.924301-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit: 63e44bc520
Check the memory operand of INS/OUTS before emulating the instruction.
The #VC exception can get raised from user-space, but the memory operand
can be manipulated to access kernel memory before the emulation actually
begins and after the exception handler has run.
[ bp: Massage commit message. ]
Fixes: 597cfe4821 ("x86/boot/compressed/64: Setup a GHCB-based VC Exception handler")
Reported-by: Tom Dohrmann <erbse.13@gmx.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit: b9cb9c4558
Check the IO permission bitmap (if present) before emulating IOIO #VC
exceptions for user-space. These permissions are checked by hardware
already before the #VC is raised, but due to the VC-handler decoding
race it needs to be checked again in software.
Fixes: 25189d08e5 ("x86/sev-es: Add support for handling IOIO exceptions")
Reported-by: Tom Dohrmann <erbse.13@gmx.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Tom Dohrmann <erbse.13@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit: a37cd2a59d
A virt scenario can be constructed where MMIO memory can be user memory.
When that happens, a race condition opens between when the hardware
raises the #VC and when the #VC handler gets to emulate the instruction.
If the MOVS is replaced with a MOVS accessing kernel memory in that
small race window, then write to kernel memory happens as the access
checks are not done at emulation time.
Disable MMIO emulation in user mode temporarily until a sensible use
case appears and justifies properly handling the race window.
Fixes: 0118b604c2 ("x86/sev-es: Handle MMIO String Instructions")
Reported-by: Tom Dohrmann <erbse.13@gmx.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Tom Dohrmann <erbse.13@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a16eb25b09 upstream.
Per the SDM, "When the local APIC handles a performance-monitoring
counters interrupt, it automatically sets the mask flag in the LVT
performance counter register." Add this behavior to KVM's local APIC
emulation.
Failure to mask the LVTPC entry results in spurious PMIs, e.g. when
running Linux as a guest, PMI handlers that do a "late_ack" spew a large
number of "dazed and confused" spurious NMI warnings.
Fixes: f5132b0138 ("KVM: Expose a version 2 architectural PMU to a guests")
Cc: stable@vger.kernel.org
Signed-off-by: Jim Mattson <jmattson@google.com>
Tested-by: Mingwei Zhang <mizhang@google.com>
Signed-off-by: Mingwei Zhang <mizhang@google.com>
Link: https://lore.kernel.org/r/20230925173448.3518223-3-mizhang@google.com
[sean: massage changelog, correct Fixes]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d9cea8a55 ]
On 8xx, PAGE_NONE is handled by setting _PAGE_NA instead of clearing
_PAGE_USER.
But then pte_user() returns 1 also for PAGE_NONE.
As _PAGE_NA prevent reads, add a specific version of pte_read()
that returns 0 when _PAGE_NA is set instead of always returning 1.
Fixes: 351750331f ("powerpc/mm: Introduce _PAGE_NA")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/57bcfbe578e43123f9ed73e040229b80f1ad56ec.1695659959.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d35652a5fc upstream.
Fei has reported that KASAN triggers during apply_alternatives() on
a 5-level paging machine:
BUG: KASAN: out-of-bounds in rcu_is_watching()
Read of size 4 at addr ff110003ee6419a0 by task swapper/0/0
...
__asan_load4()
rcu_is_watching()
trace_hardirqs_on()
text_poke_early()
apply_alternatives()
...
On machines with 5-level paging, cpu_feature_enabled(X86_FEATURE_LA57)
gets patched. It includes KASAN code, where KASAN_SHADOW_START depends on
__VIRTUAL_MASK_SHIFT, which is defined with cpu_feature_enabled().
KASAN gets confused when apply_alternatives() patches the
KASAN_SHADOW_START users. A test patch that makes KASAN_SHADOW_START
static, by replacing __VIRTUAL_MASK_SHIFT with 56, works around the issue.
Fix it for real by disabling KASAN while the kernel is patching alternatives.
[ mingo: updated the changelog ]
Fixes: 6657fca06e ("x86/mm: Allow to boot without LA57 if CONFIG_X86_5LEVEL=y")
Reported-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231012100424.1456-1-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0eee815ba upstream.
Eddie reported that newer kernels were crashing during boot on his 476
FSP2 system:
kernel tried to execute user page (b7ee2000) - exploit attempt? (uid: 0)
BUG: Unable to handle kernel instruction fetch
Faulting instruction address: 0xb7ee2000
Oops: Kernel access of bad area, sig: 11 [#1]
BE PAGE_SIZE=4K FSP-2
Modules linked in:
CPU: 0 PID: 61 Comm: mount Not tainted 6.1.55-d23900f.ppcnf-fsp2 #1
Hardware name: ibm,fsp2 476fpe 0x7ff520c0 FSP-2
NIP: b7ee2000 LR: 8c008000 CTR: 00000000
REGS: bffebd83 TRAP: 0400 Not tainted (6.1.55-d23900f.ppcnf-fs p2)
MSR: 00000030 <IR,DR> CR: 00001000 XER: 20000000
GPR00: c00110ac bffebe63 bffebe7e bffebe88 8c008000 00001000 00000d12 b7ee2000
GPR08: 00000033 00000000 00000000 c139df10 48224824 1016c314 10160000 00000000
GPR16: 10160000 10160000 00000008 00000000 10160000 00000000 10160000 1017f5b0
GPR24: 1017fa50 1017f4f0 1017fa50 1017f740 1017f630 00000000 00000000 1017f4f0
NIP [b7ee2000] 0xb7ee2000
LR [8c008000] 0x8c008000
Call Trace:
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
---[ end trace 0000000000000000 ]---
The problem is in ret_from_syscall where the check for
icache_44x_need_flush is done. When the flush is needed the code jumps
out-of-line to do the flush, and then intends to jump back to continue
the syscall return.
However the branch back to label 1b doesn't return to the correct
location, instead branching back just prior to the return to userspace,
causing bogus register values to be used by the rfi.
The breakage was introduced by commit 6f76a01173
("powerpc/syscall: implement system call entry/exit logic in C for PPC32") which
inadvertently removed the "1" label and reused it elsewhere.
Fix it by adding named local labels in the correct locations. Note that
the return label needs to be outside the ifdef so that CONFIG_PPC_47x=n
compiles.
Fixes: 6f76a01173 ("powerpc/syscall: implement system call entry/exit logic in C for PPC32")
Cc: stable@vger.kernel.org # v5.12+
Reported-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/linuxppc-dev/fdaadc46-7476-9237-e104-1d2168526e72@linux.ibm.com/
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://msgid.link/20231010114750.847794-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f454b18e07 upstream.
Fix erratum #1485 on Zen4 parts where running with STIBP disabled can
cause an #UD exception. The performance impact of the fix is negligible.
Reported-by: René Rebe <rene@exactcode.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: René Rebe <rene@exactcode.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/D99589F4-BC5D-430B-87B2-72C20370CF57@exactcode.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e53899771a upstream.
We found that a panic can occur when a vsyscall is made while LBR sampling
is active. If the vsyscall is interrupted (NMI) for perf sampling, this
call sequence can occur (most recent at top):
__insn_get_emulate_prefix()
insn_get_emulate_prefix()
insn_get_prefixes()
insn_get_opcode()
decode_branch_type()
get_branch_type()
intel_pmu_lbr_filter()
intel_pmu_handle_irq()
perf_event_nmi_handler()
Within __insn_get_emulate_prefix() at frame 0, a macro is called:
peek_nbyte_next(insn_byte_t, insn, i)
Within this macro, this dereference occurs:
(insn)->next_byte
Inspecting registers at this point, the value of the next_byte field is the
address of the vsyscall made, for example the location of the vsyscall
version of gettimeofday() at 0xffffffffff600000. The access to an address
in the vsyscall region will trigger an oops due to an unhandled page fault.
To fix the bug, filtering for vsyscalls can be done when
determining the branch type. This patch will return
a "none" branch if a kernel address if found to lie in the
vsyscall region.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: JP Kobryn <inwardvessel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cd2a30b96 upstream.
The dts file of the MediaTek MT8195 demo board has been updated to include
new reserved memory regions.
These reserved memory regions are:
- SCP
- VPU,
- Sound DMA
- APU.
These regions are defined with the "shared-dma-pool" compatible property.
In addition, the existing reserved memory regions have been reordered by
their addresses to improve readability and maintainability of the DTS
file.
Cc: stable@vger.kernel.org # 6.1, 6.4, 6.5
Fixes: e4a4175201 ("arm64: dts: mediatek: mt8195-demo: fix the memory size of node secmon")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230905034511.11232-2-macpaul.lin@mediatek.com
Link: https://lore.kernel.org/r/20231003-mediatek-fixes-v6-7-v1-3-dad7cd62a8ff@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f1b0d3d73 ]
The RISC-V architecture does not expose sub-registers, and hold all
32-bit values in a sign-extended format [1] [2]:
| The compiler and calling convention maintain an invariant that all
| 32-bit values are held in a sign-extended format in 64-bit
| registers. Even 32-bit unsigned integers extend bit 31 into bits
| 63 through 32. Consequently, conversion between unsigned and
| signed 32-bit integers is a no-op, as is conversion from a signed
| 32-bit integer to a signed 64-bit integer.
While BPF, on the other hand, exposes sub-registers, and use
zero-extension (similar to arm64/x86).
This has led to some subtle bugs, where a BPF JITted program has not
sign-extended the a0 register (return value in RISC-V land), passed
the return value up the kernel, e.g.:
| int from_bpf(void);
|
| long foo(void)
| {
| return from_bpf();
| }
Here, a0 would be 0xffff_ffff, instead of the expected
0xffff_ffff_ffff_ffff.
Internally, the RISC-V JIT uses a5 as a dedicated register for BPF
return values.
Keep a5 zero-extended, but explicitly sign-extend a0 (which is used
outside BPF land). Now that a0 (RISC-V ABI) and a5 (BPF ABI) differs,
a0 is only moved to a5 for non-BPF native calls (BPF_PSEUDO_CALL).
Fixes: 2353ecc6f9 ("bpf, riscv: add BPF JIT for RV64G")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://github.com/riscv/riscv-isa-manual/releases/download/riscv-isa-release-056b6ff-2023-10-02/unpriv-isa-asciidoc.pdf # [2]
Link: https://github.com/riscv-non-isa/riscv-elf-psabi-doc/releases/download/draft-20230929-e5c800e661a53efe3c2678d71a306323b60eb13b/riscv-abi.pdf # [2]
Link: https://lore.kernel.org/bpf/20231004120706.52848-2-bjorn@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fd1fd0104 ]
The current emit_call function is not suitable for kernel function call as
it store return value to bpf R0 register. We can separate it out for common
use. Meanwhile, simplify judgment logic, that is, fixed function address
can use jal or auipc+jalr, while the unfixed can use only auipc+jalr.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Acked-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/bpf/20230215135205.1411105-3-pulehui@huaweicloud.com
Stable-dep-of: 2f1b0d3d73 ("riscv, bpf: Sign-extend return values")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d192615c30 ]
The DSU PMU allows monitoring performance events in the DSU cluster,
which is done by configuring and reading back values from the DSU PMU
system registers. However, for write-access to be allowed by ELs lower
than EL3, the EL3 firmware needs to update the setting on the ACTLR3_EL3
register, as it is disallowed by default.
That configuration is not done on the firmware used by the MT8195 SoC,
as a consequence, booting a MT8195-based machine like
mt8195-cherry-tomato-r2 with CONFIG_ARM_DSU_PMU enabled hangs the kernel
just as it writes to the CLUSTERPMOVSCLR_EL1 register, since the
instruction faults to EL3, and BL31 apparently just re-runs the
instruction over and over.
Mark the DSU PMU node in the Devicetree with status "fail", as the
machine doesn't have a suitable firmware to make use of it from the
kernel, and allowing its driver to probe would hang the kernel.
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230720200753.322133-1-nfraprado@collabora.com
Link: https://lore.kernel.org/r/20231003-mediatek-fixes-v6-7-v1-5-dad7cd62a8ff@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cf5716acbf upstream.
Follow the example of other platforms and extend the PDC resource region
to 0x30000, so that the PDC driver can read the PDC_VERSION register.
Fixes: 397ad94668 ("arm64: dts: qcom: sm8150: Add pdc interrupt controller node")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230905-topic-sm8x50-upstream-pdc-ver-v4-2-fc633c7df84b@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 914988e099 upstream.
Back in 2005, Kyle McMartin removed the 16-byte alignment for
ldcw semaphores on PA 2.0 machines (CONFIG_PA20). This broke
spinlocks on pre PA8800 processors. The main symptom was random
faults in mmap'd memory (e.g., gcc compilations, etc).
Unfortunately, the errata for this ldcw change is lost.
The issue is the 16-byte alignment required for ldcw semaphore
instructions can only be reduced to natural alignment when the
ldcw operation can be handled coherently in cache. Only PA8800
and PA8900 processors actually support doing the operation in
cache.
Aligning the spinlock dynamically adds two integer instructions
to each spinlock.
Tested on rp3440, c8000 and a500.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Link: https://lore.kernel.org/linux-parisc/6b332788-2227-127f-ba6d-55e99ecf4ed8@bell.net/T/#t
Link: https://lore.kernel.org/linux-parisc/20050609050702.GB4641@roadwarrior.mcmartin.ca/
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bc6f7d9d7 upstream.
SNP retrieves the majority of CPUID information from the SNP CPUID page.
But there are times when that information needs to be supplemented by the
hypervisor, for example, obtaining the initial APIC ID of the vCPU from
leaf 1.
The current implementation uses the MSR protocol to retrieve the data from
the hypervisor, even when a GHCB exists. The problem arises when an NMI
arrives on return from the VMGEXIT. The NMI will be immediately serviced
and may generate a #VC requiring communication with the hypervisor.
Since a GHCB exists in this case, it will be used. As part of using the
GHCB, the #VC handler will write the GHCB physical address into the GHCB
MSR and the #VC will be handled.
When the NMI completes, processing resumes at the site of the VMGEXIT
which is expecting to read the GHCB MSR and find a CPUID MSR protocol
response. Since the NMI handling overwrote the GHCB MSR response, the
guest will see an invalid reply from the hypervisor and self-terminate.
Fix this problem by using the GHCB when it is available. Any NMI
received is properly handled because the GHCB contents are copied into
a backup page and restored on NMI exit, thus preserving the active GHCB
request or result.
[ bp: Touchups. ]
Fixes: ee0bfa08a3 ("x86/compressed/64: Add support for SEV-SNP CPUID table in #VC handlers")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/a5856fa1ebe3879de91a8f6298b6bbd901c61881.1690578565.git.thomas.lendacky@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3b3c637e4 upstream.
John David Anglin reported that giving "nr_cpus=1" on the command
line causes a crash, while "maxcpus=1" works.
Reported-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 599522d9d2 ]
Zen 4 systems running buggy microcode can hit a WARN_ON() in the PMI
handler, as shown below, several times while perf runs. A simple
`perf top` run is enough to render the system unusable:
WARNING: CPU: 18 PID: 20608 at arch/x86/events/amd/core.c:944 amd_pmu_v2_handle_irq+0x1be/0x2b0
This happens because the Performance Counter Global Status Register
(PerfCntGlobalStatus) has one or more bits set which are considered
reserved according to the "AMD64 Architecture Programmer’s Manual,
Volume 2: System Programming, 24593":
https://www.amd.com/system/files/TechDocs/24593.pdf
To make this less intrusive, warn just once if any reserved bit is set
and prompt the user to update the microcode. Also sanitize the value to
what the code is handling, so that the overflow events continue to be
handled for the number of counters that are known to be sane.
Going forward, the following microcode patch levels are recommended
for Zen 4 processors in order to avoid such issues with reserved bits:
Family=0x19 Model=0x11 Stepping=0x01: Patch=0x0a10113e
Family=0x19 Model=0x11 Stepping=0x02: Patch=0x0a10123e
Family=0x19 Model=0xa0 Stepping=0x01: Patch=0x0aa00116
Family=0x19 Model=0xa0 Stepping=0x02: Patch=0x0aa00212
Commit f2eb058afc57 ("linux-firmware: Update AMD cpu microcode") from
the linux-firmware tree has binaries that meet the minimum required
patch levels.
[ sandipan: - add message to prompt users to update microcode
- rework commit message and call out required microcode levels ]
Fixes: 7685665c39 ("perf/x86/amd/core: Add PerfMonV2 overflow handling")
Reported-by: Jirka Hladky <jhladky@redhat.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/all/3540f985652f41041e54ee82aa53e7dbd55739ae.1694696888.git.sandipan.das@amd.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23d2626b84 ]
Kernels older than v5.19 do not support PerfMonV2 and the PMI handler
does not clear the overflow bits of the PerfCntrGlobalStatus register.
Because of this, loading a recent kernel using kexec from an older
kernel can result in inconsistent register states on Zen 4 systems.
The PMI handler of the new kernel gets confused and shows a warning when
an overflow occurs because some of the overflow bits are set even if the
corresponding counters are inactive. These are remnants from overflows
that were handled by the older kernel.
During CPU hotplug, the PerfCntrGlobalCtl and PerfCntrGlobalStatus
registers should always be cleared for PerfMonV2-capable processors.
However, a condition used for NB event constaints applicable only to
older processors currently prevents this from happening. Move the reset
sequence to an appropriate place and also clear the LBR Freeze bit.
Fixes: 21d59e3e2c ("perf/x86/amd/core: Detect PerfMonV2 support")
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/882a87511af40792ba69bb0e9026f19a2e71e8a3.1694696888.git.sandipan.das@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 471470bc70 upstream.
Implement the workaround for ARM Cortex-A520 erratum 2966298. On an
affected Cortex-A520 core, a speculatively executed unprivileged load
might leak data from a privileged load via a cache side channel. The
issue only exists for loads within a translation regime with the same
translation (e.g. same ASID and VMID). Therefore, the issue only affects
the return to EL0.
The workaround is to execute a TLBI before returning to EL0 after all
loads of privileged data. A non-shareable TLBI to any address is
sufficient.
The workaround isn't necessary if page table isolation (KPTI) is
enabled, but for simplicity it will be. Page table isolation should
normally be disabled for Cortex-A520 as it supports the CSV3 feature
and the E0PD feature (used when KASLR is enabled).
Cc: stable@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230921194156.1050055-2-robh@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 479965a2b7 upstream.
ClearBHB support is indicated by the CLRBHB field in ID_AA64ISAR2_EL1.
Following some refactoring the kernel incorrectly checks the BC field
instead. Fix the detection to use the right field.
(Note: The original ClearBHB support had it as FTR_HIGHER_SAFE, but this
patch uses FTR_LOWER_SAFE, which seems more correct.)
Also fix the detection of BC (hinted conditional branches) to use
FTR_LOWER_SAFE, so that it is not reported on mismatched systems.
Fixes: 356137e68a ("arm64/sysreg: Make BHB clear feature defines match the architecture")
Fixes: 8fcc8285c0 ("arm64/sysreg: Convert ID_AA64ISAR2_EL1 to automatic generation")
Cc: stable@vger.kernel.org
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230912133429.2606875-1-kristina.martsenko@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a89c6bcdac ]
Accessing AA64MMFR1_EL1 is expensive in KVM guests, since it is emulated
in the hypervisor. In fact, ARM documentation mentions some feature
registers are not supposed to be accessed frequently by the OS, and
therefore should be emulated for guests [1].
Commit 0388f9c743 ("arm64: mm: Implement
arch_wants_old_prefaulted_pte()") introduced a read of this register in
the page fault path. But, even when the feature of setting faultaround
pages with the old flag is disabled for a given cpu, we are still paying
the cost of checking the register on every pagefault. This results in an
explosion of vmexit events in KVM guests, which directly impacts the
performance of virtualized workloads. For instance, running kernbench
yields a 15% increase in system time solely due to the increased vmexit
cycles.
This patch avoids the extra cost by using the sanitized cached value.
It should be safe to do so, since this register mustn't change for a
given cpu.
[1] https://developer.arm.com/-/media/Arm%20Developer%20Community/PDF/Learn%20the%20Architecture/Armv8-A%20virtualization.pdf?revision=a765a7df-1a00-434d-b241-357bfda2dd31
Signed-off-by: Gabriel Krisman Bertazi <krisman@suse.de>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20230109151955.8292-1-krisman@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7d3e4e9d3b upstream.
There is no code for this config option and enabling it in defconfig
causes warnings from tools which are detecting unused and obsolete
kernel config flags since the flag will be completely missing from
effective build config after "make olddefconfig".
Fixes yocto kernel recipe build time warning:
WARNING: [kernel config]: This BSP contains fragments with warnings:
...
[INFO]: the following symbols were not found in the active
configuration:
- CONFIG_COMMON_CLK_NPCM8XX
The flag was added with commit 45472f1e53
v5.19-rc4-15-g45472f1e5348 so 6.1 and 6.4 stable kernel trees are
affected.
Fixes: 45472f1e53 ("arm64: defconfig: Add Nuvoton NPCM family support")
Cc: stable@kernel.org
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Bjorn Andersson <quic_bjorande@quicinc.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Cc: Bruce Ashfield <bruce.ashfield@gmail.com>
Cc: Jon Mason <jon.mason@arm.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Ross Burton <ross@burtonini.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mikko Rapeli <mikko.rapeli@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1943feecf8 upstream.
For 64bit kernel without HIGHMEM, high_memory is the virtual address of
the highest physical address in the system. But __va(get_num_physpages()
<< PAGE_SHIFT) is not what we want for high_memory because there may be
holes in the physical address space. On the other hand, max_low_pfn is
calculated from memblock_end_of_DRAM(), which is exactly corresponding
to the highest physical address, so use it for high_memory calculation.
Cc: <stable@vger.kernel.org>
Fixes: d4b6f1562a ("LoongArch: Add Non-Uniform Memory Access (NUMA) support")
Signed-off-by: Chong Qiao <qiaochong@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2761498876 upstream.
The relocation types from 101 to 109 are used by GNU binutils >= 2.41,
add their definitions to use them in later patches.
Link: https://sourceware.org/git/?p=binutils-gdb.git;a=blob;f=include/elf/loongarch.h#l230
Cc: <stable@vger.kernel.org>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 441a5dfcd9 upstream.
All callers except the MMU notifier want to process all address spaces.
Remove the address space ID argument of for_each_tdp_mmu_root_yield_safe()
and switch the MMU notifier to use __for_each_tdp_mmu_root_yield_safe().
Extracted out of a patch by Sean Christopherson <seanjc@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50107e8b2a upstream.
The mmu_notifier path is a bit of a special snowflake, e.g. it zaps only a
single address space (because it's per-slot), and can't always yield.
Because of this, it calls kvm_tdp_mmu_zap_leafs() in ways that no one
else does.
Iterate manually over the leafs in response to an mmu_notifier
invalidation, instead of invoking kvm_tdp_mmu_zap_leafs(). Drop the
@can_yield param from kvm_tdp_mmu_zap_leafs() as its sole remaining
caller unconditionally passes "true".
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230916003916.2545000-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0096d01c4 upstream.
The checks for virtualizing TSC_AUX occur during the vCPU reset processing
path. However, at the time of initial vCPU reset processing, when the vCPU
is first created, not all of the guest CPUID information has been set. In
this case the RDTSCP and RDPID feature support for the guest is not in
place and so TSC_AUX virtualization is not established.
This continues for each vCPU created for the guest. On the first boot of
an AP, vCPU reset processing is executed as a result of an APIC INIT
event, this time with all of the guest CPUID information set, resulting
in TSC_AUX virtualization being enabled, but only for the APs. The BSP
always sees a TSC_AUX value of 0 which probably went unnoticed because,
at least for Linux, the BSP TSC_AUX value is 0.
Move the TSC_AUX virtualization enablement out of the init_vmcb() path and
into the vcpu_after_set_cpuid() path to allow for proper initialization of
the support after the guest CPUID information has been set.
With the TSC_AUX virtualization support now in the vcpu_set_after_cpuid()
path, the intercepts must be either cleared or set based on the guest
CPUID input.
Fixes: 296d5a17e7 ("KVM: SEV-ES: Use V_TSC_AUX if available instead of RDTSC/MSR_TSC_AUX intercepts")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <4137fbcb9008951ab5f0befa74a0399d2cce809a.1694811272.git.thomas.lendacky@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8d93d5d93 upstream.
svm_recalc_instruction_intercepts() is always called at least once
before the vCPU is started, so the setting or clearing of the RDTSCP
intercept can be dropped from the TSC_AUX virtualization support.
Extracted from a patch by Tom Lendacky.
Cc: stable@vger.kernel.org
Fixes: 296d5a17e7 ("KVM: SEV-ES: Use V_TSC_AUX if available instead of RDTSC/MSR_TSC_AUX intercepts")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6c2adcba5 upstream.
The SGX EPC reclaimer (ksgxd) may reclaim the SECS EPC page for an
enclave and set secs.epc_page to NULL. The SECS page is used for EAUG
and ELDU in the SGX page fault handler. However, the NULL check for
secs.epc_page is only done for ELDU, not EAUG before being used.
Fix this by doing the same NULL check and reloading of the SECS page as
needed for both EAUG and ELDU.
The SECS page holds global enclave metadata. It can only be reclaimed
when there are no other enclave pages remaining. At that point,
virtually nothing can be done with the enclave until the SECS page is
paged back in.
An enclave can not run nor generate page faults without a resident SECS
page. But it is still possible for a #PF for a non-SECS page to race
with paging out the SECS page: when the last resident non-SECS page A
triggers a #PF in a non-resident page B, and then page A and the SECS
both are paged out before the #PF on B is handled.
Hitting this bug requires that race triggered with a #PF for EAUG.
Following is a trace when it happens.
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:sgx_encl_eaug_page+0xc7/0x210
Call Trace:
? __kmem_cache_alloc_node+0x16a/0x440
? xa_load+0x6e/0xa0
sgx_vma_fault+0x119/0x230
__do_fault+0x36/0x140
do_fault+0x12f/0x400
__handle_mm_fault+0x728/0x1110
handle_mm_fault+0x105/0x310
do_user_addr_fault+0x1ee/0x750
? __this_cpu_preempt_check+0x13/0x20
exc_page_fault+0x76/0x180
asm_exc_page_fault+0x27/0x30
Fixes: 5a90d2c3f5 ("x86/sgx: Support adding of pages to an initialized enclave")
Signed-off-by: Haitao Huang <haitao.huang@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20230728051024.33063-1-haitao.huang%40linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27646b2e02 ]
It can be easy to miss that the notifier mechanism invokes the callbacks
in an atomic context, so add some comments to that effect on the two
handlers we register here.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230829063457.54157-4-bgray@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3241f260eb ]
This is called in an atomic context, so is not allowed to sleep if a
user page needs to be faulted in and has nowhere it can be deferred to.
The pagefault_disabled() function is documented as preventing user
access methods from sleeping.
In practice the page will be mapped in nearly always because we are
reading the instruction that just triggered the watchpoint trap.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230829063457.54157-3-bgray@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc879ab3ce ]
thread_change_pc() uses CPU local data, so must be protected from
swapping CPUs while it is reading the breakpoint struct.
The error is more noticeable after 1e60f3564b ("powerpc/watchpoints:
Track perf single step directly on the breakpoint"), which added an
unconditional __this_cpu_read() call in thread_change_pc(). However the
existing __this_cpu_read() that runs if a breakpoint does need to be
re-inserted has the same issue.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230829063457.54157-2-bgray@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8eb8fe67e2 ]
The dcache.cva encoding shown in the comments are wrong, it's for
dcache.cval1 (which is restricted to L1) instead.
Fix this in the comment and in the hardcoded instruction.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Tested-by: Sergey Matyukevich <sergey.matyukevich@syntacore.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guo Ren <guoren@kernel.org>
Tested-by: Drew Fustini <dfustini@baylibre.com>
Link: https://lore.kernel.org/r/20230912072410.2481-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb3255ee8f ]
Fix this makecheck warning:
drivers/parisc/sba_iommu.c:98:19: warning: symbol 'sba_list'
was not declared. Should it be static?
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b23c83ad2c ]
VMCLEAR active VMCSes before any emergency reboot, not just if the kernel
may kexec into a new kernel after a crash. Per Intel's SDM, the VMX
architecture doesn't require the CPU to flush the VMCS cache on INIT. If
an emergency reboot doesn't RESET CPUs, cached VMCSes could theoretically
be kept and only be written back to memory after the new kernel is booted,
i.e. could effectively corrupt memory after reboot.
Opportunistically remove the setting of the global pointer to NULL to make
checkpatch happy.
Cc: Andrew Cooper <Andrew.Cooper3@citrix.com>
Link: https://lore.kernel.org/r/20230721201859.2307736-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
