[ Upstream commit 2ab6b437c6 ]
The pinmux for LED3 and LED4 are incorrectly attached to the
omap3_pmx_core when they should be connected to the omap3_pmx_wkup
pin mux. This was likely masked by the fact that the bootloader
used to do all the pinmuxing.
Fixes: 0dbf99542c ("ARM: dts: am3517-evm: Add User LEDs and Pushbutton")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-ID: <20231005000402.50879-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09f8ee81b6 ]
Fixed regulator put under "regulators" node will not be populated,
unless simple-bus or something similar is used. Drop the "regulators"
wrapper node to fix this.
Fixes: 2c5e596524 ("ARM: dts: Add MDM9615 dtsi")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230924183914.51414-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edc6ef026f ]
On blanche, the GPIO keyboard fails to probe with:
sh-pfc e6060000.pinctrl: could not map pin config for "GP_11_02"
Fix this by correcting the name for this pin to "GP_11_2".
Fixes: 1f27fedead ("ARM: dts: blanche: Configure pull-up for SOFT_SW and SW25 GPIO keys")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/203128eca2261ffc33b83637818dd39c488f42b0.1693408326.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b9a4a67c6 ]
We are using a wrong mcbsp functional clock. The interconnect target module
driver provided clock for mcbsp is not same as the mcbsp functional clock
known as the gfclk main_clk. The mcbsp functional clocks for mcbsp should
have been added before we dropped the legacy platform data.
Additionally we are also missing the clock aliases for the clocks used by
the audio driver if reparenting is needed. This causes audio driver errors
like "CLKS: could not clk_get() prcm_fck" for mcbsp as reported by Andreas.
The mcbsp clock aliases too should have been added before we dropped the
legacy platform data.
Let's add the clocks and aliases with a single patch to fix the issue
similar to omap4. On omap5, there is no mcbsp4 instance on the l4_per
interconnect.
Fixes: b1da0fa21b ("ARM: OMAP2+: Drop legacy platform data for omap5 mcbsp")
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Reported-by: Andreas Kemnade <andreas@kemnade.info>
Reported-by: Péter Ujfalusi <peter.ujfalusi@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc2d819dd7 ]
We are using a wrong mcbsp functional clock. The interconnect target module
driver provided clock for mcbsp is not same as the mcbsp functional clock
known as the gfclk main_clk. The mcbsp functional clocks for mcbsp should
have been added before we dropped the legacy platform data.
Additionally we are also missing the clock aliases for the clocks used by
the audio driver if reparenting is needed. This causes audio driver errors
like "CLKS: could not clk_get() prcm_fck" for mcbsp as reported by Andreas.
The mcbsp clock aliases too should have been added before we dropped the
legacy platform data.
Let's add the clocks and aliases with a single patch to fix the issue.
Fixes: 349355ce3a ("ARM: OMAP2+: Drop legacy platform data for omap4 mcbsp")
Reported-by: Andreas Kemnade <andreas@kemnade.info>
Reported-by: Péter Ujfalusi <peter.ujfalusi@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad37b5e30 ]
On mapphone devices we may get lots of noise on the micro-USB port in debug
uart mode until the phy-cpcap-usb driver probes. Let's limit the noise by
using overrun-throttle-ms.
Note that there is also a related separate issue where the charger cable
connected may cause random sysrq requests until phy-cpcap-usb probes that
still remains.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac08bda156 ]
Commit 0840242e88 ("ARM: dts: Configure clock parent for pwm vibra")
attempted to fix the PWM settings but ended up causin an additional clock
reparenting error:
clk: failed to reparent abe-clkctrl:0060:24 to sys_clkin_ck: -22
Only timer9 is in the PER domain and can use the sys_clkin_ck clock source.
For timer8, the there is no sys_clkin_ck available as it's in the ABE
domain, instead it should use syc_clk_div_ck. However, for power
management, we want to use the always on sys_32k_ck instead.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes: 0840242e88 ("ARM: dts: Configure clock parent for pwm vibra")
Depends-on: 61978617e9 ("ARM: dts: Add minimal support for Droid Bionic xt875")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fff6f6d6e ]
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Stable-dep-of: ac08bda156 ("ARM: dts: ti: omap: motorola-mapphone: Fix abe_clkctrl warning on boot")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f15fc7c0f ]
There is no reg property for pwm-omap-dmtimer.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Stable-dep-of: ac08bda156 ("ARM: dts: ti: omap: motorola-mapphone: Fix abe_clkctrl warning on boot")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6469b2fead ]
Fix "thermal_sys: cpu_thermal: Failed to read thermal-sensors cells: -2"
error on boot for omap3/4. This is caused by wrong addressing in the dts
for bandgap sensor for single sensor instances.
Note that omap4-cpu-thermal.dtsi is shared across omap4/5 and dra7, so
we can't just change the addressing in omap4-cpu-thermal.dtsi.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes: a761d517bb ("ARM: dts: omap3: Add cpu_thermal zone")
Fixes: 0bbf6c54d1 ("arm: dts: add omap4 CPU thermal data")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c74379afd ]
There is no syna,nosleep property in Synaptics RMI4 touchscreen:
qcom-msm8974pro-sony-xperia-shinano-castor.dtb: synaptics@2c: rmi4-f01@1: 'syna,nosleep' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: ab80661883 ("ARM: dts: qcom: msm8974: Add Sony Xperia Z2 Tablet")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230720115335.137354-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31fba16c19 ]
The node names for functions of Synaptics RMI4 touchscreen must be as
"rmi4-fXX", as required by bindings and Linux driver.
qcom-msm8974pro-sony-xperia-shinano-castor.dtb: synaptics@2c: Unevaluated properties are not allowed ('rmi-f01@1', 'rmi-f11@11' were unexpected)
Fixes: ab80661883 ("ARM: dts: qcom: msm8974: Add Sony Xperia Z2 Tablet")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230720115335.137354-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43db692681 ]
There is no syna,f11-flip-x property, so assume intention was to use
touchscreen-inverted-x.
Fixes: ab80661883 ("ARM: dts: qcom: msm8974: Add Sony Xperia Z2 Tablet")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230720115335.137354-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3f3fc32e5 ]
The previous values were completely bogus, and resulted in the computed
DPI ratio being much lower than reality, causing applications and UIs to
misbehave.
The new values were measured by myself with a ruler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Fixes: 8620cc2f99 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2")
Cc: <stable@vger.kernel.org> # v5.8+
Link: https://lore.kernel.org/r/20230714153720.336990-1-paul@crapouillou.net
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91994e5907 ]
Linksys ea6500-v2 have 256MB of ram. Currently we only use 128MB.
Expand the definition to use all the available RAM.
Fixes: 03e96644d7 ("ARM: dts: BCM5301X: Add basic DT for Linksys EA6500 V2")
Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230712014017.28123-1-ansuelsmth@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5ed7a5c1f ]
Using GCC_DCD_XO_CLK as the XO clock for SDHCI controller is not correct,
it seems that I somehow made a mistake of passing it instead of the fixed
XO clock.
Fixes: 04b3b72b5b ("ARM: dts: qcom: ipq4019: Add SDHCI controller node")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811110150.229966-1-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44ad820780 ]
Both Luxul's XAP devices (XAP-810 and XAP-1440) are access points that
use a non-default design. They don't include switch but have a single
Ethernet port and BCM54210E PHY connected to the Ethernet controller's
MDIO bus.
Support for those devices regressed due to two changes:
1. Describing MDIO bus with switch
After commit 9fb90ae6ca ("ARM: dts: BCM53573: Describe on-SoC BCM53125
rev 4 switch") Linux stopped probing for MDIO devices.
2. Dropping hardcoded BCM54210E delays
In commit fea7fda7f5 ("net: phy: broadcom: Fix RGMII delays
configuration for BCM54210E") support for other PHY modes was added but
that requires a proper "phy-mode" value in DT.
Both above changes are correct (they don't need to be reverted or
anything) but they need this fix for DT data to be correct and for Linux
to work properly.
Fixes: 9fb90ae6ca ("ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230713111145.14864-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b77904ba17 ]
Backlight is supplied by DC5V regulator. The DTS has no PMIC node, so
just add a regulator-fixed to solve it and fix dtbs_check warning:
s5pv210-smdkv210.dtb: backlight: 'power-supply' is a required property
Link: https://lore.kernel.org/r/20230421095721.31857-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Stable-dep-of: 982655cb0e ("ARM: dts: samsung: s5pv210-smdkv210: correct ethernet reg addresses (split)")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3392ef368d ]
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#address-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#size-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
Two properties that need to be added later are "device_type" and
"ranges". Adding "device_type" on its own causes a new warning and the
value of "ranges" needs to be determined yet.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230707114004.2740-3-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05d2c3d552 ]
Such property simply doesn't exist (is not documented or used anywhere).
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: usb@d000: Unevaluated properties are not allowed ('#usb-cells' was unexpected)
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230707114004.2740-2-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit deb7edbc27 ]
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Fixes: 6257dfc1c4 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bcfc3cdc9 ]
The generic ADC channel binding is recommended over legacy one, update the
DT to the modern binding. No functional change. For further details, see
commit which adds the generic binding to STM32 ADC binding document:
'664b9879f5 ("dt-bindings: iio: stm32-adc: add generic channel binding")'
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Stable-dep-of: deb7edbc27 ("ARM: dts: stm32: Add missing detach mailbox for DHCOM SoM")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 966f04a89d ]
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Fixes: 6257dfc1c4 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ee0ef38aa ]
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Fixes: 6257dfc1c4 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c46e9b6cc9 ]
Use STM32 ADC generic bindings instead of legacy bindings on
emtrion GmbH Argon boards.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Stable-dep-of: 0ee0ef38aa ("ARM: dts: stm32: Add missing detach mailbox for emtrion emSBC-Argon")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86684c2481 ]
Comparing .dts files to built .dtb files yielded a few .dts files which
are never built. Add them to the build.
Signed-off-by: Rob Herring <robh@kernel.org>
Stable-dep-of: 92632115fb ("samples/bpf: fix bio latency check with tracepoint")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be18293e47 ]
If the tuning step is not set, the tuning step is set to 1.
For some sd cards, the following Tuning timeout will occur.
Tuning failed, falling back to fixed sampling clock
mmc0: Tuning failed, falling back to fixed sampling clock
So set the default tuning step. This refers to the NXP vendor's
commit below:
https://github.com/nxp-imx/linux-imx/blob/lf-6.1.y/
arch/arm/boot/dts/imx7s.dtsi#L1216-L1217
Fixes: 1e336aa0c0 ("mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a2b96e42a ]
If the tuning step is not set, the tuning step is set to 1.
For some sd cards, the following Tuning timeout will occur.
Tuning failed, falling back to fixed sampling clock
So set the default tuning step. This refers to the NXP vendor's
commit below:
https://github.com/nxp-imx/linux-imx/blob/lf-6.1.y/
arch/arm/boot/dts/imx6sx.dtsi#L1108-L1109
Fixes: 1e336aa0c0 ("mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 762b700982 ]
RTC interrupt level should be set to "LOW". This was revealed by the
introduction of commit:
f181987ef4 ("rtc: m41t80: use IRQ flags obtained from fwnode")
which changed the way IRQ type is obtained.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Stefan Riedmüller <s.riedmueller@phytec.de>
Fixes: 800d595151 ("ARM: dts: imx6: Add initial support for phyBOARD-Mira")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b0d1f2738 ]
The node names should be generic and DT schema expects certain pattern:
imx50-kobo-aura.dtb: gpio-leds: 'on' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
imx6dl-yapp4-draco.dtb: led-controller@30: 'chan@0', 'chan@1', 'chan@2' do not match any of the regexes: '^led@[0-8]$', '^multi-led@[0-8]$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stable-dep-of: 762b700982 ("ARM: dts: imx6: phytec: fix RTC interrupt level")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d14bd943f ]
Fix USB-related warnings in prtrvt, prtvt7, prti6q and prtwd2 device trees
by disabling unused usbphynop1 and usbphynop2 USB PHYs and providing proper
configuration for the over-current detection. This fixes the following
warnings with the current kernel:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over current polarity defined
By the way, fix over-current detection on usbotg port for prtvt7, prti6q
and prtwd2 boards. Only prtrvt do not have OC on USB OTG port.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit edcbdd57de upstream.
After renaming NAND controller node name from "qpic-nand" to
"nand-controller", the board DTS/DTSI also have to be updated:
Warning (unit_address_vs_reg): /soc/qpic-nand@79b0000: node has a unit name, but no reg or ranges property
Cc: <stable@vger.kernel.org>
Fixes: 9e1e00f18a ("ARM: dts: qcom: Fix node name for NAND controller node")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230420072811.36947-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fcb79ee3f0 ]
The pinctrl node was missing which change the pin mux to GPIO mode.
Add it so we don't have to rely on the bootloader to set the correct
mode.
Fixes: 79d83b3a45 ("ARM: dts: lan966x: add basic Kontron KSwitch D10 support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230616-feature-d10-dt-cleanups-v1-2-50dd0452b8fe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd274b733b ]
this typo was found by the dtbs_check
| ports:port@5:fixed-link: 'oneOf' conditional failed,
| {'speed': [[1000]], 'duplex-full': True} is not of type 'array'
| 'duplex-full' does not match any of the regexes: 'pinctrl-[0-]..."
this should have been full-duplex;
Fixes: 935327a735 ("ARM: dts: BCM5301X: Add DT for Meraki MR26")
Fixes: ec88a9c344 ("ARM: BCM5301X: Add DT for Meraki MR32")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://lore.kernel.org/r/50522f45566951a9eabd22820647924cc6b4a264.1686238550.git.chunkeey@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3f2778b1b ]
The audio routing flow is not correct, the flow should be from source
(second element in the pair) to sink (first element in the pair). The
flow now is from "HP_OUT" to "Playback", where "Playback" is source
and "HP_OUT" is sink, i.e. the direction is swapped and there is no
direct link between the two either.
Fill in the correct routing, where "HP_OUT" supplies the "Headphone Jack",
"Line In Jack" supplies "LINE_IN" input, "Microphone Jack" supplies "MIC_IN"
input and "Mic Bias" supplies "Microphone Jack".
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0501fdec10 ]
make dtbs_check:
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
PWM specifiers referring to R-Car PWM Timer Controllers should contain
only two cells.
Fix this by dropping the bogus third cell.
Fixes: 6f89dd9e93 ("ARM: dts: iwg20d-q7-common: Add LCD support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6e5c3167424a43faf8c1fa68d9667b3d87dc86d8.1684855911.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98b503c7fb ]
On Meson8 uart_B and uart_C do not work, because they are relying on
incorrect clocks. Change the references of pclk to the correct CLKID
(UART1 for uart_B and UART2 for uart_C), to allow use of the two uarts.
This was originally reported by Hans-Frieder Vogt for Meson8b [0], but
the same bug is also present in meson8.dtsi
[0] https://lore.kernel.org/linux-amlogic/trinity-bf20bcb9-790b-4ab9-99e3-0831ef8257f4-1680878185420@3c-app-gmx-bap55/
Fixes: 57007bfb54 ("ARM: dts: meson8: Fix the UART device-tree schema validation")
Reported-by: Hans-Frieder Vogt <hfdevel@gmx.net> # for meson8b.dtsi
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230516203029.1031174-1-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e60c230588 ]
Add the qcom,controlled-remotely property for the blsp2_bam
controller node. This board requires this, otherwise the board stalls
during the boot for some reason (most probably because TZ mishandles the
protection error and keeps on looping somewhere inside).
Fixes: 62bc817922 dts: msm8974: Add blsp2_bam dma node
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230507190735.2333145-3-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cf765e598 ]
Fix the following error in kernel log due to too long sound card name:
"
asoc-audio-graph-card sound: ASoC: driver name too long 'STM32MP1-AV96-HDMI' -> 'STM32MP1-AV96-H'
"
Fixes: e027da3427 ("ARM: dts: stm32: Add bindings for audio on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
