commit 8e42c301ce upstream.
Currently there is no support for earlycon on the AM654 UART
controller. This commit adds it.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231031131242.15516-1-rwahl@gmx.de
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6bb057418 upstream.
Starting RX DMA on THRI interrupt is too early because TX may not have
finished yet.
This change is inspired by commit 90b8596ac4 ("serial: 8250: Prevent
starting up DMA Rx on THRI interrupt") and fixes DMA issues I had with
an AM62 SoC that is using the 8250 OMAP variant.
Cc: stable@vger.kernel.org
Fixes: c26389f998 ("serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs")
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231101171431.16495-1-rwahl@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8973ab7a24 upstream.
This fixes commit 439c7183e5 ("serial: 8250: 8250_omap: Disable RX
interrupt after DMA enable") which unfortunately set the
UART_HAS_RHR_IT_DIS bit in the UART_OMAP_IER2 register and never
cleared it.
Cc: stable@vger.kernel.org
Fixes: 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231031110909.11695-1-rwahl@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08ce9a1b72 upstream.
This device has a silicon bug that makes it report a timeout interrupt
but no data in the FIFO.
The datasheet states the following in the errata section 18.1.4:
"If the host reads the receive FIFO at the same time as a
time-out interrupt condition happens, the host might read 0xCC
(time-out) in the Interrupt Indication Register (IIR), but bit 0
of the Line Status Register (LSR) is not set (means there is no
data in the receive FIFO)."
The errata description seems to indicate it concerns only polled mode of
operation when reading bit 0 of the LSR register. However, tests have
shown and NXP has confirmed that the RXLVL register also yields 0 when
the bug is triggered, and hence the IRQ driven implementation in this
driver is equally affected.
This bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.
Fix this by always reading one byte from the FIFO when this condition
is detected in order to clear the interrupt. This approach was
confirmed to be correct by NXP through their support channels.
Tested by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Co-Developed-by: Maxim Popov <maxim.snafu@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231123072818.1394539-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58ac1b3799 upstream.
Since there is no guarantee that the memory returned by
dma_alloc_coherent() is associated with a 'struct page', using the
architecture specific phys_to_page() is wrong, but using
virt_to_page() would be as well.
Stop using sg lists altogether and just use the *_single() functions
instead. This also simplifies the code a bit since the scatterlists in
this driver always have only one entry anyway.
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
gc: Add a commit log from the initial thread:
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
Fixes: cb06ff102e ("ARM: PL011: Add support for Rx DMA buffer polling.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20231122171503.235649-1-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4a778303e upstream.
Retrieve rs485 devicetree properties on registration of sc16is7xx ports in
case they are attached to an rs485 transceiver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-7-hugo@hugovil.com
Cc: Hugo Villeneuve <hugo@hugovil.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77a82cebf0 upstream.
According to the IOControl register bits description in the page 31 of
the product datasheet, we know the bit 3 of IOControl register is
softreset, this bit will self-clearing once the reset finish.
In the probe, the softreset bit is set, and when we read this register
from debugfs/regmap interface, we found the softreset bit is still
setting, this confused us for a while. Finally we found this register
is cached, to read the real value from register, we could put it
into the regmap_volatile().
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20230724034727.17335-1-hui.wang@canonical.com
Cc: Hugo Villeneuve <hugo@hugovil.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4876dacac upstream.
Some of the later revisions of the Brainboxes PX cards are based
on the Oxford Semiconductor chipset. Due to the chip's unique setup
these cards need to be initialised.
Previously these were tested against a reference card with the same broken
baudrate on another PC, cancelling out the effect. With this patch they
work and can transfer/receive find against an FTDI-based device.
Add all of the cards which require this setup to the quirks table.
Thanks to Maciej W. Rozycki for clarification on this chip.
Fixes: ef5a03a26c ("tty: 8250: Add support for Brainboxes PX cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB7899D222A4AB2A4E8C57108FC4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33092fb3af upstream.
The UC-257 is a serial + LPT card, so remove it from this driver.
A patch has been submitted to add it to parport_serial instead.
Additionaly, the UC-431 does not use this card ID, only the UC-420
does. The 431 is a 3-port card and there is no generic 3-port configuration
available, so remove reference to it from this driver.
Fixes: 152d1afa83 ("tty: Add support for Brainboxes UC cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB78995ADF7394C74AD4CF3357C4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae62c49c0c upstream.
The new uart_write() function is only called from suspend/resume code, causing
a build warning when those are left out:
drivers/tty/serial/8250/8250_omap.c:169:13: error: 'uart_write' defined but not used [-Werror=unused-function]
Remove the #ifdefs and use the modern pm_ops/pm_sleep_ops and their wrappers
to let the compiler see where it's used but still drop the dead code.
Fixes: 398cecc248 ("serial: 8250: omap: Fix imprecise external abort for omap_8250_pm()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230517202012.634386-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 560706eff7 ]
We now get errors on system suspend if no_console_suspend is set as
reported by Thomas. The errors started with commit 20a41a6261 ("serial:
8250_omap: Use force_suspend and resume for system suspend").
Let's fix the issue by checking for console_suspend_enabled in the system
suspend and resume path.
Note that with this fix the checks for console_suspend_enabled in
omap8250_runtime_suspend() become useless. We now keep runtime PM usage
count for an attached kernel console starting with commit bedb404e91
("serial: 8250_port: Don't use power management for kernel console").
Fixes: 20a41a6261 ("serial: 8250_omap: Use force_suspend and resume for system suspend")
Cc: stable <stable@kernel.org>
Cc: Udit Kumar <u-kumar1@ti.com>
Reported-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230926061319.15140-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 398cecc248 ]
We must idle the uart only after serial8250_unregister_port(). Otherwise
unbinding the uart via sysfs while doing cat on the port produces an
imprecise external abort:
mem_serial_in from omap_8250_pm+0x44/0xf4
omap_8250_pm from uart_hangup+0xe0/0x194
uart_hangup from __tty_hangup.part.0+0x37c/0x3a8
__tty_hangup.part.0 from uart_remove_one_port+0x9c/0x22c
uart_remove_one_port from serial8250_unregister_port+0x60/0xe8
serial8250_unregister_port from omap8250_remove+0x6c/0xd0
omap8250_remove from platform_remove+0x28/0x54
Turns out the driver needs to have runtime PM functional before the
driver probe calls serial8250_register_8250_port(). And it needs
runtime PM after driver remove calls serial8250_unregister_port().
On probe, we need to read registers before registering the port in
omap_serial_fill_features_erratas(). We do that with custom uart_read()
already.
On remove, after serial8250_unregister_port(), we need to write to the
uart registers to idle the device. Let's add a custom uart_write() for
that.
Currently the uart register access depends on port->membase to be
initialized, which won't work after serial8250_unregister_port().
Let's use priv->membase instead, and use it for runtime PM related
functions to remove the dependency to port->membase for early and
late register access.
Note that during use, we need to check for a valid port in the runtime PM
related functions. This is needed for the optional wakeup configuration.
We now need to set the drvdata a bit earlier so it's available for the
runtime PM functions.
With the port checks in runtime PM functions, the old checks for priv in
omap8250_runtime_suspend() and omap8250_runtime_resume() functions are no
longer needed and are removed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230508082014.23083-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 560706eff7 ("serial: 8250_omap: Fix errors with no_console_suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8679328eb8 ]
Commit 44b27aec9d ("serial: core, 8250: set RS485 termination GPIO in
serial core") enabled support for RS485 termination GPIOs behind i2c
expanders by setting the GPIO outside of the critical section protected
by the port spinlock. Access to the i2c expander may sleep, which
caused a splat with the port spinlock held.
Commit 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in
driver-specific way") erroneously regressed that by spinlocking the
GPIO manipulation again.
Fix by moving uart_rs485_config() (the function manipulating the GPIO)
outside of the spinlocked section and acquiring the spinlock inside of
uart_rs485_config() for the invocation of ->rs485_config() only.
This gets us one step closer to pushing the spinlock down into the
->rs485_config() callbacks which actually need it. (Some callbacks
do not want to be spinlocked because they perform sleepable register
accesses, see e.g. sc16is7xx_config_rs485().)
Stack trace for posterity:
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 56 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch
Call trace:
rcu_note_context_switch
__schedule
schedule
schedule_timeout
wait_for_completion_timeout
bcm2835_i2c_xfer
__i2c_transfer
i2c_transfer
i2c_transfer_buffer_flags
regmap_i2c_write
_regmap_raw_write_impl
_regmap_bus_raw_write
_regmap_write
_regmap_update_bits
regmap_update_bits_base
pca953x_gpio_set_value
gpiod_set_raw_value_commit
gpiod_set_value_nocheck
gpiod_set_value_cansleep
uart_rs485_config
uart_add_one_port
pl011_register_port
pl011_probe
Fixes: 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Suggested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.1+
Link: https://lore.kernel.org/r/f3a35967c28b32f3c6432d0aa5936e6a9908282d.1695307688.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 826736a6c7 ]
uart_change_speed() changes more than just speed so rename it to more
generic uart_change_line_settings().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8679328eb8 ("serial: Reduce spinlocked portion of uart_rs485_config()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cce7fc8b29 upstream.
In case the leaf driver wants to use IRQ polling (irq = 0) and
IIR register shows that an interrupt happened in the 8250 hardware
the IRQ data can be NULL. In such a case we need to skip the wake
event as we came to this path from the timer interrupt and quite
likely system is already awake.
Without this fix we have got an Oops:
serial8250: ttyS0 at I/O 0x3f8 (irq = 0, base_baud = 115200) is a 16550A
...
BUG: kernel NULL pointer dereference, address: 0000000000000010
RIP: 0010:serial8250_handle_irq+0x7c/0x240
Call Trace:
? serial8250_handle_irq+0x7c/0x240
? __pfx_serial8250_timeout+0x10/0x10
Fixes: 0ba9e3a13c ("serial: 8250: Add missing wakeup event reporting")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230831222555.614426-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0499942928 ]
Commit 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
and commit 21144bab4f ("sc16is7xx: Handle modem status lines")
changed the function of the GPIOs pins to act as modem control
lines without any possibility of selecting GPIO function.
As a consequence, applications that depends on GPIO lines configured
by default as GPIO pins no longer work as expected.
Also, the change to select modem control lines function was done only
for channel A of dual UART variants (752/762). This was not documented
in the log message.
Allow to specify GPIO or modem control line function in the device
tree, and for each of the ports (A or B).
Do so by using the new device-tree property named
"nxp,modem-control-line-ports" (property added in separate patch).
When registering GPIO chip controller, mask-out GPIO pins declared as
modem control lines according to this new DT property.
Fixes: 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
Fixes: 21144bab4f ("sc16is7xx: Handle modem status lines")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230807214556.540627-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dabc54a457 ]
Commit c8f71b49ee ("serial: sc16is7xx: setup GPIO controller later
in probe") moved GPIO setup code later in probe function. Doing so
also required to move ports cleanup code (out_ports label) after the
GPIO cleanup code.
After these moves, the out_thread label becomes misplaced and makes
part of the cleanup code illogical.
This patch remove the now obsolete out_thread label and make GPIO
setup code jump to out_ports label if it fails.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230807214556.540627-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 0499942928 ("serial: sc16is7xx: fix regression with GPIO configuration")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5abd01145d ]
In tegra_uart_hw_init(), the return value of clk_prepare_enable() should
be checked since it might fail.
Fixes: e9ea096dd2 ("serial: tegra: add serial driver")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Link: https://lore.kernel.org/r/20230817105406.228674-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9608f1887 ]
The global pointer 'sprd_port' may not zero when sprd_probe returns
failure, that is a risk for sprd_port to be accessed afterward, and
may lead to unexpected errors.
For example:
There are two UART ports, UART1 is used for console and configured in
kernel command line, i.e. "console=";
The UART1 probe failed and the memory allocated to sprd_port[1] was
released, but sprd_port[1] was not set to NULL;
In UART2 probe, the same virtual address was allocated to sprd_port[2],
and UART2 probe process finally will go into sprd_console_setup() to
register UART1 as console since it is configured as preferred console
(filled to console_cmdline[]), but the console parameters (sprd_port[1])
belong to UART2.
So move the sprd_port[] assignment to where the port already initialized
can avoid the above issue.
Fixes: b7396a38fb ("tty/serial: Add Spreadtrum sc9836-uart driver support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20230725064053.235448-1-chunyan.zhang@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9baeea723c upstream.
When configuring a pin as an output pin with a value of logic 0, we
end up as having a value of logic 1 on the output pin. Setting a
logic 0 a second time (or more) after that will correctly output a
logic 0 on the output pin.
By default, all GPIO pins are configured as inputs. When we enter
sc16is7xx_gpio_direction_output() for the first time, we first set the
desired value in IOSTATE, and then we configure the pin as an output.
The datasheet states that writing to IOSTATE register will trigger a
transfer of the value to the I/O pin configured as output, so if the
pin is configured as an input, nothing will be transferred.
Therefore, set the direction first in IODIR, and then set the desired
value in IOSTATE.
This is what is done in NXP application note AN10587.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2861ed4d6e upstream.
The sc16is7xx_config_rs485() function is called only for the second
port (index 1, channel B), causing initialization problems for the
first port.
For the sc16is7xx driver, port->membase and port->mapbase are not set,
and their default values are 0. And we set port->iobase to the device
index. This means that when the first device is registered using the
uart_add_one_port() function, the following values will be in the port
structure:
port->membase = 0
port->mapbase = 0
port->iobase = 0
Therefore, the function uart_configure_port() in serial_core.c will
exit early because of the following check:
/*
* If there isn't a port here, don't do anything further.
*/
if (!port->iobase && !port->mapbase && !port->membase)
return;
Typically, I2C and SPI drivers do not set port->membase and
port->mapbase.
The max310x driver sets port->membase to ~0 (all ones). By
implementing the same change in this driver, uart_configure_port() is
now correctly executed for all ports.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ece7b754b upstream.
The operating-performance-point vote needs to be dropped when shutting
down the port to avoid wasting power by keeping resources like power
domains in an unnecessarily high performance state (e.g. when a UART
connected Bluetooth controller is not in use).
Fixes: a5819b548a ("tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state")
Cc: stable@vger.kernel.org # 5.9
Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230714130214.14552-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dfe2aeb226 ]
Unloading a hardware specific 8250 driver can produce error "Unable to
handle kernel paging request at virtual address" about ten seconds after
unloading the driver. This happens on uart_hangup() calling
uart_change_pm().
Turns out commit 04e82793f0 ("serial: 8250: Reinit port->pm on port
specific driver unbind") was only a partial fix. If the hardware specific
driver has initialized port->pm function, we need to clear port->pm too.
Just reinitializing port->ops does not do this. Otherwise serial8250_pm()
will call port->pm() instead of serial8250_do_pm().
Fixes: 04e82793f0 ("serial: 8250: Reinit port->pm on port specific driver unbind")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230804131553.52927-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 282069845a upstream.
Do not read the data register to clear the error flags for lpuart32
platforms, the additional read may cause the receive FIFO underflow
since the DMA has already read the data register.
Actually all lpuart32 platforms support write 1 to clear those error
bits, let's use this method to better clear the error flags.
Fixes: 42b68768e5 ("serial: fsl_lpuart: DMA support for 32-bit variant")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230801022304.24251-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6bd6cd29c9 ]
Returning early from stm32_usart_serial_remove() results in a resource
leak as several cleanup functions are not called. The driver core ignores
the return value and there is no possibility to clean up later.
uart_remove_one_port() only returns non-zero if there is some
inconsistency (i.e. stm32_usart_driver.state[port->line].uart_port == NULL).
This should never happen, and even if it does it's a bad idea to exit
early in the remove callback without cleaning up.
This prepares changing the prototype of struct platform_driver::remove to
return void. See commit 5c5a7680e6 ("platform: Provide a remove callback
that returns no value") for further details about this quest.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512173810.131447-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9b8fef6345 upstream.
This function is called indirectly from the platform driver probe
function. Even if the driver is built in, it may be probed after
free_initmem() due to deferral or unbinding/binding via sysfs.
Thus the function cannot be marked as __init.
Fixes: 45c054d081 ("tty: serial: add driver for the SiFive UART")
Cc: stable <stable@kernel.org>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20230624060159.3401369-1-samuel.holland@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 748c5ea8b8 upstream.
Preserve the original value of the Divisor Latch Fraction (DLF) register.
When the DLF register is modified without preservation, it can disrupt
the baudrate settings established by firmware or bootloader, leading to
data corruption and the generation of unreadable or distorted characters.
Fixes: 701c5e73b2 ("serial: 8250_dw: add fractional divisor support")
Cc: stable <stable@kernel.org>
Signed-off-by: Ruihong Luo <colorsu1922@gmail.com>
Link: https://lore.kernel.org/stable/20230713004235.35904-1-colorsu1922%40gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230713004235.35904-1-colorsu1922@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dd8752a14 upstream.
The runtime PM state should not be changed by drivers that do not
implement runtime PM even if it happens to work around a bug in PM core.
With the wake irq arming now fixed, drop the bogus runtime PM state
update which left the device in active state (and could potentially
prevent a parent device from suspending).
Fixes: f3974413cf ("tty: serial: qcom_geni_serial: Wakeup IRQ cleanup")
Cc: 5.6+ <stable@vger.kernel.org> # 5.6+
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a82d62f708 upstream.
This reverts commit eb26dfe8aa.
Commit eb26dfe8aa ("8250: add support for ASIX devices with a FIFO
bug") merged on Jul 13, 2012 adds a quirk for PCI_VENDOR_ID_ASIX
(0x9710). But that ID is the same as PCI_VENDOR_ID_NETMOS defined in
1f8b061050c7 ("[PATCH] Netmos parallel/serial/combo support") merged
on Mar 28, 2005. In pci_serial_quirks array, the NetMos entry always
takes precedence over the ASIX entry even since it was initially
merged, code in that commit is always unreachable.
In my tests, adding the FIFO workaround to pci_netmos_init() makes no
difference, and the vendor driver also does not have such workaround.
Given that the code was never used for over a decade, it's safe to
revert it.
Also, the real PCI_VENDOR_ID_ASIX should be 0x125b, which is used on
their newer AX99100 PCIe serial controllers released on 2016. The FIFO
workaround should not be intended for these newer controllers, and it
was never implemented in vendor driver.
Fixes: eb26dfe8aa ("8250: add support for ASIX devices with a FIFO bug")
Cc: stable <stable@kernel.org>
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230619155743.827859-1-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 639949a703 upstream.
Since commit 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal
active high") RS485 reception no longer works after a transmission.
The following scenario shows the problem:
1) Open a port in RS485 mode
2) Receive data from remote (OK)
3) Transmit data to remote (OK)
4) Receive data from remote (Nothing received)
In RS485 mode, imx_uart_start_tx() calls imx_uart_stop_rx() and, when the
transmission is complete, imx_uart_stop_tx() calls imx_uart_start_rx().
Since the above commit imx_uart_stop_rx() now sets the loopback bit but
imx_uart_start_rx() does not clear it causing the hardware to remain in
loopback mode and not receive external data.
Fix this by moving the existing loopback disable code to a helper function
and calling it from imx_uart_start_rx() too.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230616104838.2729694-1-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 832e231cff upstream.
When the best clk is searched, we iterate over all possible clk.
If we find a better match, the previous one, if any, needs to be freed.
If a better match has already been found, we still need to free the new
one, otherwise it leaks.
Cc: <stable@vger.kernel.org> # v3.3+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 5f5a7a5578 ("serial: samsung: switch to clkdev based clock lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Message-ID: <cf3e0053d2fc7391b2d906a86cd01a5ef15fb9dc.1686412569.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9c09546e9 upstream.
If clk_get_rate() fails, the clk that has just been allocated needs to be
freed.
Cc: <stable@vger.kernel.org> # v3.3+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 5f5a7a5578 ("serial: samsung: switch to clkdev based clock lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Message-ID: <e4baf6039368f52e5a5453982ddcb9a330fc689e.1686412569.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27a826837e upstream.
The atmel_complete_tx_dma() function disables IRQs at the start
of the function by calling spin_lock_irqsave(&port->lock, flags);
There is no need to disable them a second time using the
spin_lock_irq() function and, in fact, doing so is a bug because
it will enable IRQs prematurely when we call spin_unlock_irq().
Just use spin_lock/unlock() instead without disabling or enabling
IRQs.
Fixes: 08f738be88 ("serial: at91: add tx dma support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/cb7c39a9-c004-4673-92e1-be4e34b85368@moroto.mountain
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20a41a6261 ]
We should not rely on autosuspend timeout for system suspend. Instead,
let's use force_suspend and force_resume functions. Otherwise the serial
port controller device may not be idled on suspend.
As we are doing a register write on suspend to configure the serial port,
we still need to runtime PM resume the port on suspend.
While at it, let's switch to pm_runtime_resume_and_get() and check for
errors returned. And let's add the missing line break before return to the
suspend function while at it.
Fixes: 09d8b2bdbc ("serial: 8250: omap: Provide ability to enable/disable UART as wakeup source")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Message-ID: <20230614045922.4798-1-tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25614735a6 ]
omap8250_irq() accesses UART_IER. This register is modified twice
by each console write (serial8250_console_write()) under the port
lock. omap8250_irq() must also take the port lock to guanentee
synchronized access to UART_IER.
Since the port lock is already being taken for the stop_rx() callback
and since it is safe to call cancel_delayed_work() while holding the
port lock, simply extend the port lock region to include UART_IER
access.
Fixes: 1fe0e1fa32 ("serial: 8250_omap: Handle optional overrun-throttle-ms property")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230525093159.223817-8-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51e45fba14 ]
The only user of the start_rx() callback (qcom_geni) directly calls
its own stop_rx() callback. Since stop_rx() requires that the
port->lock is taken and interrupts are disabled, the start_rx()
callback has the same requirement.
Fixes: cfab87c2c2 ("serial: core: Introduce callback for start_rx and do stop_rx in suspend only if this callback implementation is present.")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230525093159.223817-5-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
