[ Upstream commit b76bbf835d ]
Newer variants of Ixora boards require a power-up delay when powering up
the CAN transceiver of up to 1ms.
Cc: stable@vger.kernel.org
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 858d83ca4b ]
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3aa1a82fb ]
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc35e253d0 ]
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11ab7ad6f7 ]
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0b929f587 ]
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c248e53597 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change the node name and pass the required properties to fix the
following dt-schema warnings:
imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?'
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fb7b2a2f0 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following dt-schema warnings:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e1d7cc478 ]
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68c711b882 ]
Node names should be generic. Use 'rtc' as node name to fix
the following dt-schema warning:
imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f55da4cc3 ]
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d4ac04fa7 ]
imx7d uses two ports for 'in-ports', so the syntax port@<num> has to
be used. imx7d has both port and port@1 nodes present, raising these
error:
funnel@30041000: in-ports: More than one condition true in oneOf schema
funnel@30041000: Unevaluated properties are not allowed
('in-ports' was unexpected)
Fix this by also using port@0 for imx7s as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 710dd03464 ]
The USB SS PHY interrupt needs to be provided by the PDC interrupt
controller in order to be able to wake the system up from low-power
states.
Fixes: fea4b41022 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231213173131.29436-4-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de95f13939 ]
The USB DP/DM HS PHY interrupts need to be provided by the PDC interrupt
controller in order to be able to wake the system up from low-power
states and to be able to detect disconnect events, which requires
triggering on falling edges.
A recent commit updated the trigger type but failed to change the
interrupt provider as required. This leads to the current Linux driver
failing to probe instead of printing an error during suspend and USB
wakeup not working as intended.
Fixes: d0ec3c4c11 ("ARM: dts: qcom: sdx55: fix USB wakeup interrupt types")
Fixes: fea4b41022 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231213173131.29436-3-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84228d5e29 ]
The kernel hangs for a good 12 seconds without any info being printed to
dmesg, very early in the boot process, if this regulator is not enabled.
Force-enable it to work around this issue, until we know more about the
underlying problem.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 8620cc2f99 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2")
Cc: stable@vger.kernel.org # v5.8+
Link: https://lore.kernel.org/r/20231206221556.15348-2-paul@crapouillou.net
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0ec3c4c11 ]
The DP/DM wakeup interrupts are edge triggered and which edge to trigger
on depends on use-case and whether a Low speed or Full/High speed device
is connected.
Fixes: fea4b41022 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231120164331.8116-2-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfc3c6743d ]
The binding erroneously decreed that the SCMI variants of the ST
evaluation kits are compatible with the non-SCMI variants.
This is not correct, as a kernel or bootloader compatible with the non-SCMI
variant is not necessarily able to function, when direct access
to resources is replaced by having to talk SCMI to the secure monitor.
The binding has been adjusted to reflect thus, so synchronize the device
trees now.
Fixes: 5b7e58313a ("ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554557542e ]
The XOADC is present at the address 0x197 rather than just 197. It
doesn't change a lot (since the driver hardcodes all register
addresses), but the DT should present correct address anyway.
Fixes: c4b70883ee ("ARM: dts: add XOADC and IIO HWMON to APQ8064")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230928110309.1212221-3-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b6a51aab5 ]
With subtle timings changes, we can now sometimes get an external abort on
non-linefetch error booting am3 devices at sysc_reset(). This is because
of a missing reset delay needed for the usb target module.
Looks like we never enabled the delay earlier for am3, although a similar
issue was seen earlier with a similar usb setup for dm814x as described in
commit ebf2441480 ("ARM: OMAP2+: Use srst_udelay for USB on dm814x").
Cc: stable@vger.kernel.org
Fixes: 0782e8572c ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e5caee2ba ]
This node can access any part of the L3 configuration registers space,
including CLK1 and CLK2 which are 0x800000 offset. Restore this area
size to include these areas.
Fixes: 7f2659ce65 ("ARM: dts: Move dra7 l3 noc to a separate node")
Signed-off-by: Andrew Davis <afd@ti.com>
Message-ID: <20231113181604.546444-1-afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63ef8fc9bc ]
Per root-node.yaml, 'model' is a required property.
Pass it to fix the following dt-schema warning:
imx28-xea.dtb: /: 'model' is a required property
from schema $id: http://devicetree.org/schemas/root-node.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Fixes: 445ae16ac1 ("ARM: dts: imx28: Add DTS description of imx28 based XEA board")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d951f8f5f2 ]
Since commit c7e73b5051 ("ARM: imx: mach-imx6ul: remove 14x14 EVK
specific PHY fixup")thet Ethernet PHY is no longer configured via code
in board file.
This caused Ethernet to stop working.
Fix this problem by describing the clocks and clock-names to the
Ethernet PHY node so that the KSZ8081 chip can be clocked correctly.
Fixes: c7e73b5051 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific PHY fixup")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ab6b437c6 ]
The pinmux for LED3 and LED4 are incorrectly attached to the
omap3_pmx_core when they should be connected to the omap3_pmx_wkup
pin mux. This was likely masked by the fact that the bootloader
used to do all the pinmuxing.
Fixes: 0dbf99542c ("ARM: dts: am3517-evm: Add User LEDs and Pushbutton")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-ID: <20231005000402.50879-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09f8ee81b6 ]
Fixed regulator put under "regulators" node will not be populated,
unless simple-bus or something similar is used. Drop the "regulators"
wrapper node to fix this.
Fixes: 2c5e596524 ("ARM: dts: Add MDM9615 dtsi")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230924183914.51414-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edc6ef026f ]
On blanche, the GPIO keyboard fails to probe with:
sh-pfc e6060000.pinctrl: could not map pin config for "GP_11_02"
Fix this by correcting the name for this pin to "GP_11_2".
Fixes: 1f27fedead ("ARM: dts: blanche: Configure pull-up for SOFT_SW and SW25 GPIO keys")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/203128eca2261ffc33b83637818dd39c488f42b0.1693408326.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b9a4a67c6 ]
We are using a wrong mcbsp functional clock. The interconnect target module
driver provided clock for mcbsp is not same as the mcbsp functional clock
known as the gfclk main_clk. The mcbsp functional clocks for mcbsp should
have been added before we dropped the legacy platform data.
Additionally we are also missing the clock aliases for the clocks used by
the audio driver if reparenting is needed. This causes audio driver errors
like "CLKS: could not clk_get() prcm_fck" for mcbsp as reported by Andreas.
The mcbsp clock aliases too should have been added before we dropped the
legacy platform data.
Let's add the clocks and aliases with a single patch to fix the issue
similar to omap4. On omap5, there is no mcbsp4 instance on the l4_per
interconnect.
Fixes: b1da0fa21b ("ARM: OMAP2+: Drop legacy platform data for omap5 mcbsp")
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Reported-by: Andreas Kemnade <andreas@kemnade.info>
Reported-by: Péter Ujfalusi <peter.ujfalusi@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc2d819dd7 ]
We are using a wrong mcbsp functional clock. The interconnect target module
driver provided clock for mcbsp is not same as the mcbsp functional clock
known as the gfclk main_clk. The mcbsp functional clocks for mcbsp should
have been added before we dropped the legacy platform data.
Additionally we are also missing the clock aliases for the clocks used by
the audio driver if reparenting is needed. This causes audio driver errors
like "CLKS: could not clk_get() prcm_fck" for mcbsp as reported by Andreas.
The mcbsp clock aliases too should have been added before we dropped the
legacy platform data.
Let's add the clocks and aliases with a single patch to fix the issue.
Fixes: 349355ce3a ("ARM: OMAP2+: Drop legacy platform data for omap4 mcbsp")
Reported-by: Andreas Kemnade <andreas@kemnade.info>
Reported-by: Péter Ujfalusi <peter.ujfalusi@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad37b5e30 ]
On mapphone devices we may get lots of noise on the micro-USB port in debug
uart mode until the phy-cpcap-usb driver probes. Let's limit the noise by
using overrun-throttle-ms.
Note that there is also a related separate issue where the charger cable
connected may cause random sysrq requests until phy-cpcap-usb probes that
still remains.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac08bda156 ]
Commit 0840242e88 ("ARM: dts: Configure clock parent for pwm vibra")
attempted to fix the PWM settings but ended up causin an additional clock
reparenting error:
clk: failed to reparent abe-clkctrl:0060:24 to sys_clkin_ck: -22
Only timer9 is in the PER domain and can use the sys_clkin_ck clock source.
For timer8, the there is no sys_clkin_ck available as it's in the ABE
domain, instead it should use syc_clk_div_ck. However, for power
management, we want to use the always on sys_32k_ck instead.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes: 0840242e88 ("ARM: dts: Configure clock parent for pwm vibra")
Depends-on: 61978617e9 ("ARM: dts: Add minimal support for Droid Bionic xt875")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fff6f6d6e ]
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Stable-dep-of: ac08bda156 ("ARM: dts: ti: omap: motorola-mapphone: Fix abe_clkctrl warning on boot")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f15fc7c0f ]
There is no reg property for pwm-omap-dmtimer.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Stable-dep-of: ac08bda156 ("ARM: dts: ti: omap: motorola-mapphone: Fix abe_clkctrl warning on boot")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6469b2fead ]
Fix "thermal_sys: cpu_thermal: Failed to read thermal-sensors cells: -2"
error on boot for omap3/4. This is caused by wrong addressing in the dts
for bandgap sensor for single sensor instances.
Note that omap4-cpu-thermal.dtsi is shared across omap4/5 and dra7, so
we can't just change the addressing in omap4-cpu-thermal.dtsi.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes: a761d517bb ("ARM: dts: omap3: Add cpu_thermal zone")
Fixes: 0bbf6c54d1 ("arm: dts: add omap4 CPU thermal data")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c74379afd ]
There is no syna,nosleep property in Synaptics RMI4 touchscreen:
qcom-msm8974pro-sony-xperia-shinano-castor.dtb: synaptics@2c: rmi4-f01@1: 'syna,nosleep' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: ab80661883 ("ARM: dts: qcom: msm8974: Add Sony Xperia Z2 Tablet")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230720115335.137354-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31fba16c19 ]
The node names for functions of Synaptics RMI4 touchscreen must be as
"rmi4-fXX", as required by bindings and Linux driver.
qcom-msm8974pro-sony-xperia-shinano-castor.dtb: synaptics@2c: Unevaluated properties are not allowed ('rmi-f01@1', 'rmi-f11@11' were unexpected)
Fixes: ab80661883 ("ARM: dts: qcom: msm8974: Add Sony Xperia Z2 Tablet")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230720115335.137354-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43db692681 ]
There is no syna,f11-flip-x property, so assume intention was to use
touchscreen-inverted-x.
Fixes: ab80661883 ("ARM: dts: qcom: msm8974: Add Sony Xperia Z2 Tablet")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230720115335.137354-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3f3fc32e5 ]
The previous values were completely bogus, and resulted in the computed
DPI ratio being much lower than reality, causing applications and UIs to
misbehave.
The new values were measured by myself with a ruler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Fixes: 8620cc2f99 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2")
Cc: <stable@vger.kernel.org> # v5.8+
Link: https://lore.kernel.org/r/20230714153720.336990-1-paul@crapouillou.net
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91994e5907 ]
Linksys ea6500-v2 have 256MB of ram. Currently we only use 128MB.
Expand the definition to use all the available RAM.
Fixes: 03e96644d7 ("ARM: dts: BCM5301X: Add basic DT for Linksys EA6500 V2")
Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230712014017.28123-1-ansuelsmth@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5ed7a5c1f ]
Using GCC_DCD_XO_CLK as the XO clock for SDHCI controller is not correct,
it seems that I somehow made a mistake of passing it instead of the fixed
XO clock.
Fixes: 04b3b72b5b ("ARM: dts: qcom: ipq4019: Add SDHCI controller node")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811110150.229966-1-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44ad820780 ]
Both Luxul's XAP devices (XAP-810 and XAP-1440) are access points that
use a non-default design. They don't include switch but have a single
Ethernet port and BCM54210E PHY connected to the Ethernet controller's
MDIO bus.
Support for those devices regressed due to two changes:
1. Describing MDIO bus with switch
After commit 9fb90ae6ca ("ARM: dts: BCM53573: Describe on-SoC BCM53125
rev 4 switch") Linux stopped probing for MDIO devices.
2. Dropping hardcoded BCM54210E delays
In commit fea7fda7f5 ("net: phy: broadcom: Fix RGMII delays
configuration for BCM54210E") support for other PHY modes was added but
that requires a proper "phy-mode" value in DT.
Both above changes are correct (they don't need to be reverted or
anything) but they need this fix for DT data to be correct and for Linux
to work properly.
Fixes: 9fb90ae6ca ("ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230713111145.14864-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b77904ba17 ]
Backlight is supplied by DC5V regulator. The DTS has no PMIC node, so
just add a regulator-fixed to solve it and fix dtbs_check warning:
s5pv210-smdkv210.dtb: backlight: 'power-supply' is a required property
Link: https://lore.kernel.org/r/20230421095721.31857-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Stable-dep-of: 982655cb0e ("ARM: dts: samsung: s5pv210-smdkv210: correct ethernet reg addresses (split)")
Signed-off-by: Sasha Levin <sashal@kernel.org>
