commit 3a38a829c8 upstream.
The function platform_get_resource was replaced with
devm_platform_ioremap_resource_byname and is called using 0 as name.
This eventually ends up in platform_get_resource_byname in the call
stack, where it causes a null pointer in strcmp.
if (type == resource_type(r) && !strcmp(r->name, name))
It should have been replaced with devm_platform_ioremap_resource.
Fixes: bd69058f50 ("net: ll_temac: Use devm_platform_ioremap_resource_byname()")
Signed-off-by: Claus Hansen Ries <chr@terma.com>
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/cca18f9c630a41c18487729770b492bb@terma.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 045a5b645d upstream.
Since the dump_data (struct iwl_fwrt_dump_data) is a union,
it's not safe to unconditionally access and use the 'trig'
member, it might be 'desc' instead. Access it only if it's
known to be 'trig' rather than 'desc', i.e. if ini-debug
is present.
Cc: stable@vger.kernel.org
Fixes: 0eb50c674a ("iwlwifi: yoyo: send hcmd to fw after dump collection completes.")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.e2976bc58b29.I72fbd6135b3623227de53d8a2bb82776066cb72b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71cbd32e3d ]
The previous commit fixed a bug that led to a NULL peer->device being
dereferenced. It's actually easier and faster performance-wise to
instead get the device from ctx->wg. This semantically makes more sense
too, since ctx->wg->peer_allowedips.seq is compared with
ctx->allowedips_seq, basing them both in ctx. This also acts as a
defence in depth provision against freed peers.
Cc: stable@vger.kernel.org
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55b6c73867 ]
If all peers are removed via wg_peer_remove_all(), rather than setting
peer_list to empty, the peer is added to a temporary list with a head on
the stack of wg_peer_remove_all(). If a netlink dump is resumed and the
cursored peer is one that has been removed via wg_peer_remove_all(), it
will iterate from that peer and then attempt to dump freed peers.
Fix this by instead checking peer->is_dead, which was explictly created
for this purpose. Also move up the device_update_lock lockdep assertion,
since reading is_dead relies on that.
It can be reproduced by a small script like:
echo "Setting config..."
ip link add dev wg0 type wireguard
wg setconf wg0 /big-config
(
while true; do
echo "Showing config..."
wg showconf wg0 > /dev/null
done
) &
sleep 4
wg setconf wg0 <(printf "[Peer]\nPublicKey=$(wg genkey)\n")
Resulting in:
BUG: KASAN: slab-use-after-free in __lock_acquire+0x182a/0x1b20
Read of size 8 at addr ffff88811956ec70 by task wg/59
CPU: 2 PID: 59 Comm: wg Not tainted 6.8.0-rc2-debug+ #5
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x70
print_address_description.constprop.0+0x2c/0x380
print_report+0xab/0x250
kasan_report+0xba/0xf0
__lock_acquire+0x182a/0x1b20
lock_acquire+0x191/0x4b0
down_read+0x80/0x440
get_peer+0x140/0xcb0
wg_get_device_dump+0x471/0x1130
Cc: stable@vger.kernel.org
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Reported-by: Lillian Berry <lillian@star-ark.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f9952e8d8 ]
The __string() and __assign_str() helper macros of the TRACE_EVENT() macro
are going through some optimizations where only the source string of
__string() will be used and the __assign_str() source will be ignored and
later removed.
To make sure that there's no issues, a new check is added between the
__string() src argument and the __assign_str() src argument that does a
strcmp() to make sure they are the same string.
The hclgevf trace events have:
__assign_str(devname, &hdev->nic.kinfo.netdev->name);
Which triggers the warning:
hclgevf_trace.h:34:39: error: passing argument 1 of ‘strcmp’ from incompatible pointer type [-Werror=incompatible-pointer-types]
34 | __assign_str(devname, &hdev->nic.kinfo.netdev->name);
[..]
arch/x86/include/asm/string_64.h:75:24: note: expected ‘const char *’ but argument is of type ‘char (*)[16]’
75 | int strcmp(const char *cs, const char *ct);
| ~~~~~~~~~~~~^~
Because __assign_str() now has:
WARN_ON_ONCE(__builtin_constant_p(src) ? \
strcmp((src), __data_offsets.dst##_ptr_) : \
(src) != __data_offsets.dst##_ptr_); \
The problem is the '&' on hdev->nic.kinfo.netdev->name. That's because
that name is:
char name[IFNAMSIZ]
Where passing an address '&' of a char array is not compatible with strcmp().
The '&' is not necessary, remove it.
Link: https://lore.kernel.org/linux-trace-kernel/20240313093454.3909afe7@gandalf.local.home
Cc: netdev <netdev@vger.kernel.org>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Yufeng Mo <moyufeng@huawei.com>
Cc: Huazhong Tan <tanhuazhong@huawei.com>
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Jijie Shao <shaojijie@huawei.com>
Fixes: d8355240cf ("net: hns3: add trace event support for PF/VF mailbox")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f7352557a ]
This is the candidate patch of CVE-2023-47233 :
https://nvd.nist.gov/vuln/detail/CVE-2023-47233
In brcm80211 driver,it starts with the following invoking chain
to start init a timeout worker:
->brcmf_usb_probe
->brcmf_usb_probe_cb
->brcmf_attach
->brcmf_bus_started
->brcmf_cfg80211_attach
->wl_init_priv
->brcmf_init_escan
->INIT_WORK(&cfg->escan_timeout_work,
brcmf_cfg80211_escan_timeout_worker);
If we disconnect the USB by hotplug, it will call
brcmf_usb_disconnect to make cleanup. The invoking chain is :
brcmf_usb_disconnect
->brcmf_usb_disconnect_cb
->brcmf_detach
->brcmf_cfg80211_detach
->kfree(cfg);
While the timeout woker may still be running. This will cause
a use-after-free bug on cfg in brcmf_cfg80211_escan_timeout_worker.
Fix it by deleting the timer and canceling the worker in
brcmf_cfg80211_detach.
Fixes: e756af5b30 ("brcmfmac: add e-scan support.")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Cc: stable@vger.kernel.org
[arend.vanspriel@broadcom.com: keep timer delete as is and cancel work just before free]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240107072504.392713-1-arend.vanspriel@broadcom.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69ddba9d17 ]
Currently, the MT753X switches treat frames with :01-0D and :0F MAC DAs as
regular multicast frames, therefore flooding them to user ports.
On page 205, section "8.6.3 Frame filtering" of the active standard, IEEE
Std 802.1Q™-2022, it is stated that frames with 01:80:C2:00:00:00-0F as MAC
DA must only be propagated to C-VLAN and MAC Bridge components. That means
VLAN-aware and VLAN-unaware bridges. On the switch designs with CPU ports,
these frames are supposed to be processed by the CPU (software). So we make
the switch only forward them to the CPU port. And if received from a CPU
port, forward to a single port. The software is responsible of making the
switch conform to the latter by setting a single port as destination port
on the special tag.
This switch intellectual property cannot conform to this part of the
standard fully. Whilst the REV_UN frame tag covers the remaining :04-0D and
:0F MAC DAs, it also includes :22-FF which the scope of propagation is not
supposed to be restricted for these MAC DAs.
Set frames with :01-03 MAC DAs to be trapped to the CPU port(s). Add a
comment for the remaining MAC DAs.
Note that the ingress port must have a PVID assigned to it for the switch
to forward untagged frames. A PVID is set by default on VLAN-aware and
VLAN-unaware ports. However, when the network interface that pertains to
the ingress port is attached to a vlan_filtering enabled bridge, the user
can remove the PVID assignment from it which would prevent the link-local
frames from being trapped to the CPU port. I am yet to see a way to forward
link-local frames while preventing other untagged frames from being
forwarded too.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8bf353577 ]
Whether VLAN-aware or not, on every VID VLAN table entry that has the CPU
port as a member of it, frames are set to egress the CPU port with the VLAN
tag stacked. This is so that VLAN tags can be appended after hardware
special tag (called DSA tag in the context of Linux drivers).
For user ports on a VLAN-unaware bridge, frame ingressing the user port
egresses CPU port with only the special tag.
For user ports on a VLAN-aware bridge, frame ingressing the user port
egresses CPU port with the special tag and the VLAN tag.
This causes issues with link-local frames, specifically BPDUs, because the
software expects to receive them VLAN-untagged.
There are two options to make link-local frames egress untagged. Setting
CONSISTENT or UNTAGGED on the EG_TAG bits on the relevant register.
CONSISTENT means frames egress exactly as they ingress. That means
egressing with the VLAN tag they had at ingress or egressing untagged if
they ingressed untagged. Although link-local frames are not supposed to be
transmitted VLAN-tagged, if they are done so, when egressing through a CPU
port, the special tag field will be broken.
BPDU egresses CPU port with VLAN tag egressing stacked, received on
software:
00:01:25.104821 AF Unknown (382365846), length 106:
| STAG | | VLAN |
0x0000: 0000 6c27 614d 4143 0001 0000 8100 0001 ..l'aMAC........
0x0010: 0026 4242 0300 0000 0000 0000 6c27 614d .&BB........l'aM
0x0020: 4143 0000 0000 0000 6c27 614d 4143 0000 AC......l'aMAC..
0x0030: 0000 1400 0200 0f00 0000 0000 0000 0000 ................
BPDU egresses CPU port with VLAN tag egressing untagged, received on
software:
00:23:56.628708 AF Unknown (25215488), length 64:
| STAG |
0x0000: 0000 6c27 614d 4143 0001 0000 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
BPDU egresses CPU port with VLAN tag egressing tagged, received on
software:
00:01:34.311963 AF Unknown (25215488), length 64:
| Mess |
0x0000: 0000 6c27 614d 4143 0001 0001 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
To prevent confusing the software, force the frame to egress UNTAGGED
instead of CONSISTENT. This way, frames can't possibly be received TAGGED
by software which would have the special tag field broken.
VLAN Tag Egress Procedure
For all frames, one of these options set the earliest in this order will
apply to the frame:
- EG_TAG in certain registers for certain frames.
This will apply to frame with matching MAC DA or EtherType.
- EG_TAG in the address table.
This will apply to frame at its incoming port.
- EG_TAG in the PVC register.
This will apply to frame at its incoming port.
- EG_CON and [EG_TAG per port] in the VLAN table.
This will apply to frame at its outgoing port.
- EG_TAG in the PCR register.
This will apply to frame at its outgoing port.
EG_TAG in certain registers for certain frames:
PPPoE Discovery_ARP/RARP: PPP_EG_TAG and ARP_EG_TAG in the APC register.
IGMP_MLD: IGMP_EG_TAG and MLD_EG_TAG in the IMC register.
BPDU and PAE: BPDU_EG_TAG and PAE_EG_TAG in the BPC register.
REV_01 and REV_02: R01_EG_TAG and R02_EG_TAG in the RGAC1 register.
REV_03 and REV_0E: R03_EG_TAG and R0E_EG_TAG in the RGAC2 register.
REV_10 and REV_20: R10_EG_TAG and R20_EG_TAG in the RGAC3 register.
REV_21 and REV_UN: R21_EG_TAG and RUN_EG_TAG in the RGAC4 register.
With this change, it can be observed that a bridge interface with stp_state
and vlan_filtering enabled will properly block ports now.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50e60de381 ]
For PF to AF interrupt vector and VF to AF vector same
interrupt handler is registered which is causing race condition.
When two interrupts are raised to two CPUs at same time
then two cores serve same event corrupting the data.
Fixes: 7304ac4567 ("octeontx2-af: Add mailbox IRQ and msg handlers")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfcf6355f5 ]
When PF sending link status messages to VF, it is possible
that by the time link_event_task work function is executed
VF might have brought down. Hence before sending VF link
status message check whether VF is up to receive it.
Fixes: ad513ed938 ("octeontx2-vf: Link event notification support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7558ce0d97 ]
Only one execution context for the workqueue used for PF and
VFs mailbox communication is incorrect since multiple works are
queued simultaneously by all the VFs and PF link UP messages.
Hence use default number of execution contexts by passing zero
as max_active to alloc_workqueue function. With this fix in place,
modify UP messages also to wait until completion.
Fixes: d424b6c024 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 289f974674 ]
BACKGROUND
==========
When multiple work items are queued to a workqueue, their execution order
doesn't match the queueing order. They may get executed in any order and
simultaneously. When fully serialized execution - one by one in the queueing
order - is needed, an ordered workqueue should be used which can be created
with alloc_ordered_workqueue().
However, alloc_ordered_workqueue() was a later addition. Before it, an
ordered workqueue could be obtained by creating an UNBOUND workqueue with
@max_active==1. This originally was an implementation side-effect which was
broken by 4c16bd327c ("workqueue: restore WQ_UNBOUND/max_active==1 to be
ordered"). Because there were users that depended on the ordered execution,
5c0338c687 ("workqueue: restore WQ_UNBOUND/max_active==1 to be ordered")
made workqueue allocation path to implicitly promote UNBOUND workqueues w/
@max_active==1 to ordered workqueues.
While this has worked okay, overloading the UNBOUND allocation interface
this way creates other issues. It's difficult to tell whether a given
workqueue actually needs to be ordered and users that legitimately want a
min concurrency level wq unexpectedly gets an ordered one instead. With
planned UNBOUND workqueue updates to improve execution locality and more
prevalence of chiplet designs which can benefit from such improvements, this
isn't a state we wanna be in forever.
This patch series audits all callsites that create an UNBOUND workqueue w/
@max_active==1 and converts them to alloc_ordered_workqueue() as necessary.
WHAT TO LOOK FOR
================
The conversions are from
alloc_workqueue(WQ_UNBOUND | flags, 1, args..)
to
alloc_ordered_workqueue(flags, args...)
which don't cause any functional changes. If you know that fully ordered
execution is not ncessary, please let me know. I'll drop the conversion and
instead add a comment noting the fact to reduce confusion while conversion
is in progress.
If you aren't fully sure, it's completely fine to let the conversion
through. The behavior will stay exactly the same and we can always
reconsider later.
As there are follow-up workqueue core changes, I'd really appreciate if the
patch can be routed through the workqueue tree w/ your acks. Thanks.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sunil Goutham <sgoutham@marvell.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Ratheesh Kannoth <rkannoth@marvell.com>
Cc: Srujana Challa <schalla@marvell.com>
Cc: Geetha sowjanya <gakula@marvell.com>
Cc: netdev@vger.kernel.org
Stable-dep-of: 7558ce0d97 ("octeontx2-pf: Use default max_active works instead of one")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a88e0f936b ]
A single line of interrupt is used to receive up notifications
and down reply messages from AF to PF (similarly from PF to its VF).
PF acts as bridge and forwards VF messages to AF and sends respsones
back from AF to VF. When an async event like link event is received
by up message when PF is in middle of forwarding VF message then
mailbox errors occur because PF state machine is corrupted.
Since VF is a separate driver or VF driver can be in a VM it is
not possible to serialize from the start of communication at VF.
Hence to differentiate between type of messages at PF this patch makes
sender to set mbox data register with distinct values for up and down
messages. Sender also checks whether previous interrupt is received
before triggering current interrupt by waiting for mailbox data register
to become zero.
Fixes: 5a6d7c9dae ("octeontx2-pf: Mailbox communication with AF")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8299ffe3dc ]
CPT HW would trigger the CPT AF FLT interrupt when CPT engines
hits some uncorrectable errors and AF is the one which receives
the interrupt and recovers the engines.
This patch adds a mailbox for CPT VFs to request for CPT faulted
and recovered engines info.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: a88e0f936b ("octeontx2: Detect the mbox up or down message via register")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9adb04ff62 ]
Optimize CPT PF identification in mbox handling for faster
mbox response by doing it at AF driver probe instead of
every mbox message.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: a88e0f936b ("octeontx2: Detect the mbox up or down message via register")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f58cf765e8 ]
On OcteonTX2 SoC, the admin function (AF) is the only one with all
priviliges to configure HW and alloc resources, PFs and it's VFs
have to request AF via mailbox for all their needs.
This patch adds a new mailbox for CPT VFs to request for CPT LF
reset.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: a88e0f936b ("octeontx2: Detect the mbox up or down message via register")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07ea567d84 ]
When CPT engine has uncorrectable errors, it will get halted and
must be disabled and re-enabled. This patch adds code for the same.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: a88e0f936b ("octeontx2: Detect the mbox up or down message via register")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d27e2da94a ]
Fix race condition leading to system crash during EEH error handling
During EEH error recovery, the bnx2x driver's transmit timeout logic
could cause a race condition when handling reset tasks. The
bnx2x_tx_timeout() schedules reset tasks via bnx2x_sp_rtnl_task(),
which ultimately leads to bnx2x_nic_unload(). In bnx2x_nic_unload()
SGEs are freed using bnx2x_free_rx_sge_range(). However, this could
overlap with the EEH driver's attempt to reset the device using
bnx2x_io_slot_reset(), which also tries to free SGEs. This race
condition can result in system crashes due to accessing freed memory
locations in bnx2x_free_rx_sge()
799 static inline void bnx2x_free_rx_sge(struct bnx2x *bp,
800 struct bnx2x_fastpath *fp, u16 index)
801 {
802 struct sw_rx_page *sw_buf = &fp->rx_page_ring[index];
803 struct page *page = sw_buf->page;
....
where sw_buf was set to NULL after the call to dma_unmap_page()
by the preceding thread.
EEH: Beginning: 'slot_reset'
PCI 0011:01:00.0#10000: EEH: Invoking bnx2x->slot_reset()
bnx2x: [bnx2x_io_slot_reset:14228(eth1)]IO slot reset initializing...
bnx2x 0011:01:00.0: enabling device (0140 -> 0142)
bnx2x: [bnx2x_io_slot_reset:14244(eth1)]IO slot reset --> driver unload
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc0080000025065fc
Oops: Kernel access of bad area, sig: 11 [#1]
.....
Call Trace:
[c000000003c67a20] [c00800000250658c] bnx2x_io_slot_reset+0x204/0x610 [bnx2x] (unreliable)
[c000000003c67af0] [c0000000000518a8] eeh_report_reset+0xb8/0xf0
[c000000003c67b60] [c000000000052130] eeh_pe_report+0x180/0x550
[c000000003c67c70] [c00000000005318c] eeh_handle_normal_event+0x84c/0xa60
[c000000003c67d50] [c000000000053a84] eeh_event_handler+0xf4/0x170
[c000000003c67da0] [c000000000194c58] kthread+0x1c8/0x1d0
[c000000003c67e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64
To solve this issue, we need to verify page pool allocations before
freeing.
Fixes: 4cace675d6 ("bnx2x: Alloc 4k fragment for each rx ring buffer element")
Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240315205535.1321-1-thinhtr@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32fa4366cc ]
read_poll_timeout inside phy_read_poll_timeout can set val negative
in some cases (for example, __mdiobus_read inside phy_read can return
-EOPNOTSUPP).
Supposedly, commit 4ec7329517 ("net: phylib: fix phy_read*_poll_timeout()")
should fix problems with wrong-signed vals, but I do not see how
as val is sent to phy_read as is and __val = phy_read (not val)
is checked for sign.
Change val type for signed to allow better error handling as done in other
phy_read_poll_timeout callers. This will not fix any error handling
by itself, but allows, for example, to modify cond with appropriate
sign check or check resulting val separately.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 014068dcb5 ("net: phy: genphy_loopback: add link speed configuration")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f490c492e9 ]
On MT7530, the HT_XTAL_FSEL field of the HWTRAP register stores a 2-bit
value that represents the frequency of the crystal oscillator connected to
the switch IC. The field is populated by the state of the ESW_P4_LED_0 and
ESW_P4_LED_0 pins, which is done right after reset is deasserted.
ESW_P4_LED_0 ESW_P3_LED_0 Frequency
-----------------------------------------
0 0 Reserved
0 1 20MHz
1 0 40MHz
1 1 25MHz
On MT7531, the XTAL25 bit of the STRAP register stores this. The LAN0LED0
pin is used to populate the bit. 25MHz when the pin is high, 40MHz when
it's low.
These pins are also used with LEDs, therefore, their state can be set to
something other than the bootstrapping configuration. For example, a link
may be established on port 3 before the DSA subdriver takes control of the
switch which would set ESW_P3_LED_0 to high.
Currently on mt7530_setup() and mt7531_setup(), 1000 - 1100 usec delay is
described between reset assertion and deassertion. Some switch ICs in real
life conditions cannot always have these pins set back to the bootstrapping
configuration before reset deassertion in this amount of delay. This causes
wrong crystal frequency to be selected which puts the switch in a
nonfunctional state after reset deassertion.
The tests below are conducted on an MT7530 with a 40MHz crystal oscillator
by Justin Swartz.
With a cable from an active peer connected to port 3 before reset, an
incorrect crystal frequency (0b11 = 25MHz) is selected:
[1] [3] [5]
: : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
_____________________________
ESW_P3_LED_0 |__________________________
: : : :
: : [4]...:
: :
[2]................:
[1] Reset is asserted.
[2] Period of 1000 - 1100 usec.
[3] Reset is deasserted.
[4] Period of 315 usec. HWTRAP register is populated with incorrect
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
Increase the delay between reset_control_assert() and
reset_control_deassert(), and gpiod_set_value_cansleep(priv->reset, 0) and
gpiod_set_value_cansleep(priv->reset, 1) to 5000 - 5100 usec. This amount
ensures a higher possibility that the switch IC will have these pins back
to the bootstrapping configuration before reset deassertion.
With a cable from an active peer connected to port 3 before reset, the
correct crystal frequency (0b10 = 40MHz) is selected:
[1] [2-1] [3] [5]
: : : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
___________________ _______
ESW_P3_LED_0 |_________| |__________________
: : : : :
: [2-2]...: [4]...:
[2]................:
[1] Reset is asserted.
[2] Period of 5000 - 5100 usec.
[2-1] ESW_P3_LED_0 goes low.
[2-2] Remaining period of 5000 - 5100 usec.
[3] Reset is deasserted.
[4] Period of 310 usec. HWTRAP register is populated with bootstrapped
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
ESW_P3_LED_0 low period before reset deassertion:
5000 usec
- 5100 usec
TEST RESET HOLD
# (usec)
---------------------
1 5410
2 5440
3 4375
4 5490
5 5475
6 4335
7 4370
8 5435
9 4205
10 4335
11 3750
12 3170
13 4395
14 4375
15 3515
16 4335
17 4220
18 4175
19 4175
20 4350
Min 3170
Max 5490
Median 4342.500
Avg 4466.500
Revert commit 2920dd92b9 ("net: dsa: mt7530: disable LEDs before reset").
Changing the state of pins via reset assertion is simpler and more
efficient than doing so by setting the LED controller off.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Co-developed-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7db7775ea ]
Commit d3256efd8e ("veth: allow enabling NAPI even without XDP") tried to fix
the fact that GRO was not possible without XDP, because veth did not use NAPI
without XDP. However, it also introduced the behaviour that GRO is always
enabled, when XDP is enabled.
While it might be desired for most cases, it is confusing for the user at best
as the GRO flag suddenly changes, when an XDP program is attached. It also
introduces some complexities in state management as was partially addressed in
commit fe9f801355 ("net: veth: clear GRO when clearing XDP even when down").
But the biggest problem is that it is not possible to disable GRO at all, when
an XDP program is attached, which might be needed for some use cases.
Fix this by not touching the GRO flag on XDP enable/disable as the code already
supports switching to NAPI if either GRO or XDP is requested.
Link: https://lore.kernel.org/lkml/20240311124015.38106-1-ignat@cloudflare.com/
Fixes: d3256efd8e ("veth: allow enabling NAPI even without XDP")
Fixes: fe9f801355 ("net: veth: clear GRO when clearing XDP even when down")
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea80e3ed09 ]
A patch to resolve an issue was found in MediaTek's GPL-licensed SDK:
In the mtk_ppe_stop() function, the PPE scan mode is not disabled before
disabling the PPE. This can potentially lead to a hang during the process
of disabling the PPE.
Without this patch, the PPE may experience a hang during the reboot test.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/b40da332dfe763932a82f9f62a4709457a15dd6c
Fixes: ba37b7caf1 ("net: ethernet: mtk_eth_soc: add support for initializing the PPE")
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1b85ef15a ]
Clearing bit MAC_MCR_FORCE_LINK which forces the link down too early
can result in MAC ending up in a broken/blocked state.
Fix this by handling this bit in the .mac_link_up and .mac_link_down
calls instead of in .mac_finish.
Fixes: b8fc9f3082 ("net: ethernet: mediatek: Add basic PHYLINK support")
Suggested-by: Mason-cw Chang <Mason-cw.Chang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e642921dfe ]
Use wake_up API instead of wake_up_interruptible, since
wait_event_timeout API is used for waiting on command completion.
Fixes: 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84e95149bd ]
The kmalloc_array() in nfp_fl_lag_do_work() will return null, if
the physical memory has run out. As a result, if we dereference
the acti_netdevs, the null pointer dereference bugs will happen.
This patch adds a check to judge whether allocation failure occurs.
If it happens, the delayed work will be rescheduled and try again.
Fixes: bb9a8d0311 ("nfp: flower: monitor and offload LAG groups")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Link: https://lore.kernel.org/r/20240308142540.9674-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8a5c731fd ]
The logic for enabling the TX clock shift is inverse of enabling the RX
clock shift. The TX clock shift is disabled when DP83822_TX_CLK_SHIFT is
set. Correct the current behavior and always write the delay configuration
to ensure consistent delay settings regardless of bootloader configuration.
Reference: https://www.ti.com/lit/ds/symlink/dp83822i.pdf p. 69
Fixes: 8095295292 ("net: phy: DP83822: Add setting the fixed internal delay")
Signed-off-by: Tim Pambor <tp@osasysteme.de>
Link: https://lore.kernel.org/r/20240305110608.104072-1-tp@osasysteme.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d80f79dd ]
Currently, the mac port is fixed to configured as full dplex mode in
hclge_mac_init() when driver initialization or reset restore. Users may
change the mode to half duplex with ethtool, so it may cause the user
configuration dropped after reset.
To fix it, don't change the duplex mode when resetting.
Fixes: 2d03eacc0b ("net: hns3: Only update mac configuation when necessary")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07a1d6dc90 ]
In hns3_dcbnl_ieee_delapp, should check ieee_delapp not ieee_setapp.
This path fix the wrong judgment.
Fixes: 0ba22bcb22 ("net: hns3: add support config dscp map to tc")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4469c0c5b1 ]
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.
Fixes: 92252eec91 ("net: phy: Add a helper to return the index for of the internal delay")
Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07161b2416 ]
Add check for usbnet_get_endpoints() and return the error if it fails
in order to transfer the error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 19a38d8e0a ("USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support")
Link: https://lore.kernel.org/r/20240305075927.261284-1-nichen@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee14cc9ea1 ]
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The E1000_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read E1000_TSIRC into 'tsicr';
2. handle the interrupts present into 'tsirc' and mark them in 'ack';
3. write 'ack' into E1000_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 00c65578b4 ("igb: enable internal PPS for the i210")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c238adbc57 ]
total_fa_cnt is supposed to include cck_fa_cnt and ofdm_fa_cnt, not just
ofdm_fa_cnt.
Fixes: 960361238b ("rtw88: 8821c: add false alarm statistics")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/f3cb6d17-e4e4-44a7-9c9b-72aed994b5c9@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1dfa21427 ]
Tenda U9 V2.0, which contains RTL8811CU, is practically unusable because
of frequent disconnections:
Feb 23 14:46:45 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:46 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:46:52 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:46:54 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:55 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:47:01 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:47:04 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:47:05 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
This is caused by a mistake in the chip initialisation. This version of
the chip requires loading an extra AGC table right after the main one,
but the extra table is being loaded at the wrong time, in
rtw_chip_board_info_setup().
Move the extra AGC table loading to the right place, in
rtw_phy_load_tables().
The rtw_chip_board_info_setup() can only do "software" things, and
rtw_phy_load_tables() can really do IO.
Fixes: 5d6651fe85 ("rtw88: 8821c: support RFE type2 wifi NIC")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/276c31d8-b9a8-4e54-a3ac-09b74657aff7@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3ec643947 ]
This reverts commit fcf690b0b4.
When using a wilc1000 chip over a spi bus, users can optionally define a
reset gpio and a chip enable gpio. The reset line of wilc1000 is active
low, so to hold the chip in reset, a low (physical) value must be applied.
The corresponding device tree binding documentation was introduced by
commit f31ee3c0a5 ("wilc1000: Document enable-gpios and reset-gpios
properties") and correctly indicates that the reset line is an active-low
signal. The corresponding driver part, brought by commit ec031ac479
("wilc1000: Add reset/enable GPIO support to SPI driver") was applying the
correct logic. But commit fcf690b0b4 ("wifi: wilc1000: use correct
sequence of RESET for chip Power-UP/Down") eventually flipped this logic
and started misusing the gpiod APIs, applying an inverted logic when
powering up/down the chip (for example, setting the reset line to a logic
"1" during power up, which in fact asserts the reset line when device tree
describes the reset line as GPIO_ACTIVE_LOW). As a consequence, any
platform currently using the driver in SPI mode must use a faulty reset
line description in device tree, or else chip will be maintained in reset
and will not even allow to bring up the chip.
Fix reset line usage by inverting back the gpiod APIs usage, setting the
reset line to the logic value "0" when powering the chip, and the logic
value "1" when powering off the chip.
Fixes: fcf690b0b4 ("wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240217-wilc_1000_reset_line-v2-1-b216f433d7d5@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78e886ba2b ]
Avoid the following warnings by removing the ena_select_queue() function
and rely on the net core to do the queue selection, The issue happen
when an skb received from an interface with more queues than ena is
forwarded to the ena interface.
[ 1176.159959] eth0 selects TX queue 11, but real number of TX queues is 8
[ 1176.863976] eth0 selects TX queue 14, but real number of TX queues is 8
[ 1180.767877] eth0 selects TX queue 14, but real number of TX queues is 8
[ 1188.703742] eth0 selects TX queue 14, but real number of TX queues is 8
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Kamal Heib <kheib@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1ea6db35f ]
An old cleanup went a little too far and causes a warning with clang-16
and higher as it breaks control flow integrity (KCFI) rules:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy_shim.c:64:34: error: cast from 'void (*)(struct brcms_phy *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
64 | brcms_init_timer(physhim->wl, (void (*)(void *))fn,
| ^~~~~~~~~~~~~~~~~~~~
Change this one instance back to passing a void pointer so it can be
used with the timer callback interface.
Fixes: d89a4c8060 ("staging: brcm80211: removed void * from softmac phy")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240213100548.457854-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb5942b77c ]
wilc_netdev_cleanup currently triggers a KASAN warning, which can be
observed on interface registration error path, or simply by
removing the module/unbinding device from driver:
echo spi0.1 > /sys/bus/spi/drivers/wilc1000_spi/unbind
==================================================================
BUG: KASAN: slab-use-after-free in wilc_netdev_cleanup+0x508/0x5cc
Read of size 4 at addr c54d1ce8 by task sh/86
CPU: 0 PID: 86 Comm: sh Not tainted 6.8.0-rc1+ #117
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x58
dump_stack_lvl from print_report+0x154/0x500
print_report from kasan_report+0xac/0xd8
kasan_report from wilc_netdev_cleanup+0x508/0x5cc
wilc_netdev_cleanup from wilc_bus_remove+0xc8/0xec
wilc_bus_remove from spi_remove+0x8c/0xac
spi_remove from device_release_driver_internal+0x434/0x5f8
device_release_driver_internal from unbind_store+0xbc/0x108
unbind_store from kernfs_fop_write_iter+0x398/0x584
kernfs_fop_write_iter from vfs_write+0x728/0xf88
vfs_write from ksys_write+0x110/0x1e4
ksys_write from ret_fast_syscall+0x0/0x1c
[...]
Allocated by task 1:
kasan_save_track+0x30/0x5c
__kasan_kmalloc+0x8c/0x94
__kmalloc_node+0x1cc/0x3e4
kvmalloc_node+0x48/0x180
alloc_netdev_mqs+0x68/0x11dc
alloc_etherdev_mqs+0x28/0x34
wilc_netdev_ifc_init+0x34/0x8ec
wilc_cfg80211_init+0x690/0x910
wilc_bus_probe+0xe0/0x4a0
spi_probe+0x158/0x1b0
really_probe+0x270/0xdf4
__driver_probe_device+0x1dc/0x580
driver_probe_device+0x60/0x140
__driver_attach+0x228/0x5d4
bus_for_each_dev+0x13c/0x1a8
bus_add_driver+0x2a0/0x608
driver_register+0x24c/0x578
do_one_initcall+0x180/0x310
kernel_init_freeable+0x424/0x484
kernel_init+0x20/0x148
ret_from_fork+0x14/0x28
Freed by task 86:
kasan_save_track+0x30/0x5c
kasan_save_free_info+0x38/0x58
__kasan_slab_free+0xe4/0x140
kfree+0xb0/0x238
device_release+0xc0/0x2a8
kobject_put+0x1d4/0x46c
netdev_run_todo+0x8fc/0x11d0
wilc_netdev_cleanup+0x1e4/0x5cc
wilc_bus_remove+0xc8/0xec
spi_remove+0x8c/0xac
device_release_driver_internal+0x434/0x5f8
unbind_store+0xbc/0x108
kernfs_fop_write_iter+0x398/0x584
vfs_write+0x728/0xf88
ksys_write+0x110/0x1e4
ret_fast_syscall+0x0/0x1c
[...]
David Mosberger-Tan initial investigation [1] showed that this
use-after-free is due to netdevice unregistration during vif list
traversal. When unregistering a net device, since the needs_free_netdev has
been set to true during registration, the netdevice object is also freed,
and as a consequence, the corresponding vif object too, since it is
attached to it as private netdevice data. The next occurrence of the loop
then tries to access freed vif pointer to the list to move forward in the
list.
Fix this use-after-free thanks to two mechanisms:
- navigate in the list with list_for_each_entry_safe, which allows to
safely modify the list as we go through each element. For each element,
remove it from the list with list_del_rcu
- make sure to wait for RCU grace period end after each vif removal to make
sure it is safe to free the corresponding vif too (through
unregister_netdev)
Since we are in a RCU "modifier" path (not a "reader" path), and because
such path is expected not to be concurrent to any other modifier (we are
using the vif_mutex lock), we do not need to use RCU list API, that's why
we can benefit from list_for_each_entry_safe.
[1] https://lore.kernel.org/linux-wireless/ab077dbe58b1ea5de0a3b2ca21f275a07af967d2.camel@egauge.net/
Fixes: 8399918f30 ("staging: wilc1000: use RCU list to maintain vif interfaces list")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240212-wilc_rework_deinit-v1-1-9203ae56c27f@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5bd4041cd ]
The firmware (later) actually uses the values even for keys
that are invalid as far as the host is concerned, later in
rekeying, and then only sets the low 48 bits since the PNs
are only 48 bits over the air. It does, however, compare the
full 64 bits later, obviously causing problems.
Remove the memset and use kzalloc instead to avoid any old
heap data leaking to the firmware. We already init all the
other fields in the struct anyway. This leaves the data set
to zero for any unused fields, so the firmware can look at
them safely even if they're not used right now.
Fixes: 79e561f0f0 ("iwlwifi: mvm: d3: implement RSC command version 5")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.462101146fef.I10f3855b99417af4247cff04af78dcbc6cb75c9c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f0e4aede0 ]
In the for statement of lbs_allocate_cmd_buffer(), if the allocation of
cmdarray[i].cmdbuf fails, both cmdarray and cmdarray[i].cmdbuf needs to
be freed. Otherwise, there will be memleaks in lbs_allocate_cmd_buffer().
Fixes: 876c9d3aeb ("[PATCH] Marvell Libertas 8388 802.11b/g USB driver")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126075336.2825608-1-alexious@zju.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b802e7b7e7 ]
Currently in ath11k_peer_assoc_h_he() rx_mcs_80 and rx_mcs_160
are used to calculate max_nss, see
if (support_160)
max_nss = min(rx_mcs_80, rx_mcs_160);
else
max_nss = rx_mcs_80;
Kernel test robot complains on uninitialized symbols:
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_160'.
drivers/net/wireless/ath/ath11k/mac.c:2323 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
This is because there are some code paths that never set them, so
the assignment of max_nss can come from uninitialized variables.
This could result in some unknown issues since a wrong peer_nss
might be passed to firmware.
Change to initialize them to an invalid value at the beginning. This
makes sense because even max_nss gets an invalid value, due to either
or both of them being invalid, we can get an valid peer_nss with
following guard:
arg->peer_nss = min(sta->deflink.rx_nss, max_nss)
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 3db26ecf71 ("ath11k: calculate the correct NSS of peer for HE capabilities")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401311243.NyXwWZxP-lkp@intel.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240202023547.11141-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8d8f39111 ]
EWRD ACPI table contains up to 3 additional sar profiles.
According to the BIOS spec, the table contains a n_profile
variable indicating how many additional profiles exist in the
table.
Currently we check that n_profiles is not <= 0.
But according to the BIOS spec, 0 is a valid value,
and it can't be < 0 anyway because we receive that from ACPI as
an unsigned integer.
Fixes: 39c1a9728f ("iwlwifi: refactor the SAR tables from mvm to acpi")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240129211905.448ea2f40814.Iffd2aadf8e8693e6cb599bee0406a800a0c1e081@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea1d166fae ]
The iwl_fw_ini_debug_info_tlv is used as a string, so we must
ensure the string is terminated correctly before using it.
Fixes: a9248de424 ("iwlwifi: dbg_ini: add TLV allocation new API support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240128084842.be15e858ee89.Ibff93429cf999eafc7b26f3eef4c055dc84984a0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91380f768d ]
Andrei reports that we just silently drop beacons after we
report the key counters, but never report to userspace, so
wpa_supplicant cannot send the WNM action frame. Fix that.
Fixes: b1fdc2505a ("iwlwifi: mvm: advertise BIGTK client support if available")
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240128084842.7d855442cdce.Iba90b26f893dc8c49bfb8be65373cd0a138af12c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24355fcb0d ]
The ath9k_wmi_event_tasklet() used in ath9k_htc assumes that all the data
structures have been fully initialised by the time it runs. However, because of
the order in which things are initialised, this is not guaranteed to be the
case, because the device is exposed to the USB subsystem before the ath9k driver
initialisation is completed.
We already committed a partial fix for this in commit:
8b3046abc9 ("ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()")
However, that commit only aborted the WMI_TXSTATUS_EVENTID command in the event
tasklet, pairing it with an "initialisation complete" bit in the TX struct. It
seems syzbot managed to trigger the race for one of the other commands as well,
so let's just move the existing synchronisation bit to cover the whole
tasklet (setting it at the end of ath9k_htc_probe_device() instead of inside
ath9k_tx_init()).
Link: https://lore.kernel.org/r/ed1d2c66-1193-4c81-9542-d514c29ba8b8.bugreport@ubisectech.com
Fixes: 8b3046abc9 ("ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()")
Reported-by: Ubisectech Sirius <bugreport@ubisectech.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240126140218.1033443-1-toke@toke.dk
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50180c7f8e ]
debugfs_create_dir() returns ERR_PTR and never return NULL.
As Russell suggested, this patch removes the error checking for
debugfs_create_dir(). This is because the DebugFS kernel API is developed
in a way that the caller can safely ignore the errors that occur during
the creation of DebugFS nodes. The debugfs APIs have a IS_ERR() judge in
start_creating() which can handle it gracefully. So these checks are
unnecessary.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20230903030216.1509013-3-ruanjinjie@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12cfc9c8d3 ]
Adding then removing a second vif currently makes the first vif not working
anymore. This is visible for example when we have a first interface
connected to some access point:
- create a wpa_supplicant.conf with some AP credentials
- wpa_supplicant -Dnl80211 -c /etc/wpa_supplicant.conf -i wlan0
- dhclient wlan0
- iw phy phy0 interface add wlan1 type managed
- iw dev wlan1 del
wlan0 does not manage properly traffic anymore (eg: ping not working)
This is due to vif mode being incorrectly reconfigured with some default
values in del_virtual_intf, affecting by default first vif.
Prevent first vif from being affected on second vif removal by removing vif
mode change command in del_virtual_intf
Fixes: 9bc061e880 ("staging: wilc1000: added support to dynamically add/remove interfaces")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-5-54d29463a738@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 328efda22a ]
Commit 09ed8bfc52 ("wilc1000: Rename workqueue from "WILC_wq" to
"NETDEV-wq"") moved workqueue creation in wilc_netdev_ifc_init in order to
set the interface name in the workqueue name. However, while the driver
needs only one workqueue, the wilc_netdev_ifc_init is called each time we
add an interface over a phy, which in turns overwrite the workqueue with a
new one. This can be observed with the following commands:
for i in $(seq 0 10)
do
iw phy phy0 interface add wlan1 type managed
iw dev wlan1 del
done
ps -eo pid,comm|grep wlan
39 kworker/R-wlan0
98 kworker/R-wlan1
102 kworker/R-wlan1
105 kworker/R-wlan1
108 kworker/R-wlan1
111 kworker/R-wlan1
114 kworker/R-wlan1
117 kworker/R-wlan1
120 kworker/R-wlan1
123 kworker/R-wlan1
126 kworker/R-wlan1
129 kworker/R-wlan1
Fix this leakage by putting back hif_workqueue allocation in
wilc_cfg80211_init. Regarding the workqueue name, it is indeed relevant to
set it lowercase, however it is not attached to a specific netdev, so
enforcing netdev name in the name is not so relevant. Still, enrich the
name with the wiphy name to make it clear which phy is using the workqueue.
Fixes: 09ed8bfc52 ("wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-3-54d29463a738@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
