commit 06dfcd4098 upstream.
The commit 40b5d2f15c ("net: dsa: mt7530: Add support for EEE features")
brought EEE support but did not enable EEE on MT7531 switch MACs. EEE is
enabled on MT7531 switch MACs by pulling the LAN2LED0 pin low on the board
(bootstrapping), unsetting the EEE_DIS bit on the trap register, or setting
the internal EEE switch bit on the CORE_PLL_GROUP4 register. Thanks to
SkyLake Huang (黃啟澤) from MediaTek for providing information on the
internal EEE switch bit.
There are existing boards that were not designed to pull the pin low.
Because of that, the EEE status currently depends on the board design.
The EEE_DIS bit on the trap pertains to the LAN2LED0 pin which is usually
used to control an LED. Once the bit is unset, the pin will be low. That
will make the active low LED turn on. The pin is controlled by the switch
PHY. It seems that the PHY controls the pin in the way that it inverts the
pin state. That means depending on the wiring of the LED connected to
LAN2LED0 on the board, the LED may be on without an active link.
To not cause this unwanted behaviour whilst enabling EEE on all boards, set
the internal EEE switch bit on the CORE_PLL_GROUP4 register.
My testing on MT7531 shows a certain amount of traffic loss when EEE is
enabled. That said, I haven't come across a board that enables EEE. So
enable EEE on the switch MACs but disable EEE advertisement on the switch
PHYs. This way, we don't change the behaviour of the majority of the boards
that have this switch. The mediatek-ge PHY driver already disables EEE
advertisement on the switch PHYs but my testing shows that it is somehow
enabled afterwards. Disabling EEE advertisement before the PHY driver
initialises keeps it off.
With this change, EEE can now be enabled using ethtool.
Fixes: 40b5d2f15c ("net: dsa: mt7530: Add support for EEE features")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240408-for-net-mt7530-fix-eee-for-mt7531-mt7988-v3-1-84fdef1f008b@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f563c31ff upstream.
The MT7530 switch after reset initialises with a core clock frequency that
works with a 25MHz XTAL connected to it. For 40MHz XTAL, the core clock
frequency must be set to 500MHz.
The mt7530_pll_setup() function is responsible of setting the core clock
frequency. Currently, it runs on MT7530 with 25MHz and 40MHz XTAL. This
causes MT7530 switch with 25MHz XTAL to egress and ingress frames
improperly.
Introduce a check to run it only on MT7530 with 40MHz XTAL.
The core clock frequency is set by writing to a switch PHY's register.
Access to the PHY's register is done via the MDIO bus the switch is also
on. Therefore, it works only when the switch makes switch PHYs listen on
the MDIO bus the switch is on. This is controlled either by the state of
the ESW_P1_LED_1 pin after reset deassertion or modifying bit 5 of the
modifiable trap register.
When ESW_P1_LED_1 is pulled high, PHY indirect access is used. That means
accessing PHY registers via the PHY indirect access control register of the
switch.
When ESW_P1_LED_1 is pulled low, PHY direct access is used. That means
accessing PHY registers via the MDIO bus the switch is on.
For MT7530 switch with 40MHz XTAL on a board with ESW_P1_LED_1 pulled high,
the core clock frequency won't be set to 500MHz, causing the switch to
egress and ingress frames improperly.
Run mt7530_pll_setup() after PHY direct access is set on the modifiable
trap register.
With these two changes, all MT7530 switches with 25MHz and 40MHz, and
P1_LED_1 pulled high or low, will egress and ingress frames properly.
Link: 4a5dd143f2/linux-mt/drivers/net/ethernet/mediatek/gsw_mt7623.c (L1039)
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240320-for-net-mt7530-fix-25mhz-xtal-with-direct-phy-access-v1-1-d92f605f1160@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b79d7c14f4 upstream.
Since the introduction of the OF bindings, DSA has always had a policy that
in case multiple CPU ports are present in the device tree, the numerically
smallest one is always chosen.
The MT7530 switch family, except the switch on the MT7988 SoC, has 2 CPU
ports, 5 and 6, where port 6 is preferable on the MT7531BE switch because
it has higher bandwidth.
The MT7530 driver developers had 3 options:
- to modify DSA when the MT7531 switch support was introduced, such as to
prefer the better port
- to declare both CPU ports in device trees as CPU ports, and live with the
sub-optimal performance resulting from not preferring the better port
- to declare just port 6 in the device tree as a CPU port
Of course they chose the path of least resistance (3rd option), kicking the
can down the road. The hardware description in the device tree is supposed
to be stable - developers are not supposed to adopt the strategy of
piecemeal hardware description, where the device tree is updated in
lockstep with the features that the kernel currently supports.
Now, as a result of the fact that they did that, any attempts to modify the
device tree and describe both CPU ports as CPU ports would make DSA change
its default selection from port 6 to 5, effectively resulting in a
performance degradation visible to users with the MT7531BE switch as can be
seen below.
Without preferring port 6:
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-20.00 sec 374 MBytes 157 Mbits/sec 734 sender
[ 5][TX-C] 0.00-20.00 sec 373 MBytes 156 Mbits/sec receiver
[ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 778 Mbits/sec 0 sender
[ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 777 Mbits/sec receiver
With preferring port 6:
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 856 Mbits/sec 273 sender
[ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 855 Mbits/sec receiver
[ 7][RX-C] 0.00-20.00 sec 1.72 GBytes 737 Mbits/sec 15 sender
[ 7][RX-C] 0.00-20.00 sec 1.71 GBytes 736 Mbits/sec receiver
Using one port for WAN and the other ports for LAN is a very popular use
case which is what this test emulates.
As such, this change proposes that we retroactively modify stable kernels
(which don't support the modification of the CPU port assignments, so as to
let user space fix the problem and restore the throughput) to keep the
mt7530 driver preferring port 6 even with device trees where the hardware
is more fully described.
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff221029a5 upstream.
MT7531_CPU_PMAP represents the destination port mask for trapped-to-CPU
frames (further restricted by PCR_MATRIX).
Currently the driver sets the first CPU port as the single port in this bit
mask, which works fine regardless of whether the device tree defines port
5, 6 or 5+6 as CPU ports. This is because the logic coincides with DSA's
logic of picking the first CPU port as the CPU port that all user ports are
affine to, by default.
An upcoming change would like to influence DSA's selection of the default
CPU port to no longer be the first one, and in that case, this logic needs
adaptation.
Since there is no observed leakage or duplication of frames if all CPU
ports are defined in this bit mask, simply include them all.
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c24cd679b0 ]
The TX and RX DMA Channels used by the driver to exchange data with CPSW
are not guaranteed to be in a clean state during driver initialization.
The Bootloader could have used the same DMA Channels without cleaning them
up in the event of failure. Thus, reset and disable the DMA Channels to
ensure that they are in a clean state before using them.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240417095425.2253876-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d59cf049c8 ]
This switch intellectual property provides a bit on the ARL global control
register which controls allowing mirroring frames which are received on the
local port (monitor port). This bit is unset after reset.
This ability must be enabled to fully support the port mirroring feature on
this switch intellectual property.
Therefore, this patch fixes the traffic not being reflected on a port,
which would be configured like below:
tc qdisc add dev swp0 clsact
tc filter add dev swp0 ingress matchall skip_sw \
action mirred egress mirror dev swp0
As a side note, this configuration provides the hairpinning feature for a
single port.
Fixes: 37feab6076 ("net: dsa: mt7530: add support for port mirroring")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8bbc07ac5 ]
vhost_worker will call tun call backs to receive packets. If too many
illegal packets arrives, tun_do_read will keep dumping packet contents.
When console is enabled, it will costs much more cpu time to dump
packet and soft lockup will be detected.
net_ratelimit mechanism can be used to limit the dumping rate.
PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980"
#0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253
#1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3
#2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e
#3 [fffffe00003fced0] do_nmi at ffffffff8922660d
#4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663
[exception RIP: io_serial_in+20]
RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002
RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000
RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0
RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f
R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020
R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#5 [ffffa655314979e8] io_serial_in at ffffffff89792594
#6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470
#7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6
#8 [ffffa65531497a20] uart_console_write at ffffffff8978b605
#9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558
#10 [ffffa65531497ac8] console_unlock at ffffffff89316124
#11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07
#12 [ffffa65531497b68] printk at ffffffff89318306
#13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765
#14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun]
#15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun]
#16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net]
#17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost]
#18 [ffffa65531497f10] kthread at ffffffff892d2e72
#19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f
Fixes: ef3db4a595 ("tun: avoid BUG, dump packet on GSO errors")
Signed-off-by: Lei Chen <lei.chen@smartx.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20240415020247.2207781-1-lei.chen@smartx.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7327871572 ]
The check for flags is done to not pass empty lookups to adding switch
rule functions. Since metadata is always added to lookups there is no
need to check against the flag.
It is also fixing the problem with such rule:
$ tc filter add dev gtp_dev ingress protocol ip prio 0 flower \
enc_dst_port 2123 action drop
Switch block in case of GTP can't parse the destination port, because it
should always be set to GTP specific value. The same with ethertype. The
result is that there is no other matching criteria than GTP tunnel. In
this case flags is 0, rule can't be added only because of defensive
check against flags.
Fixes: 9a225f81f5 ("ice: Support GTP-U and GTP-C offload in switchdev")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef965764c ]
When disabling aRFS under the `priv->state_lock`, any scheduled
aRFS works are canceled using the `cancel_work_sync` function,
which waits for the work to end if it has already started.
However, while waiting for the work handler, the handler will
try to acquire the `state_lock` which is already acquired.
The worker acquires the lock to delete the rules if the state
is down, which is not the worker's responsibility since
disabling aRFS deletes the rules.
Add an aRFS state variable, which indicates whether the aRFS is
enabled and prevent adding rules when the aRFS is disabled.
Kernel log:
======================================================
WARNING: possible circular locking dependency detected
6.7.0-rc4_net_next_mlx5_5483eb2 #1 Tainted: G I
------------------------------------------------------
ethtool/386089 is trying to acquire lock:
ffff88810f21ce68 ((work_completion)(&rule->arfs_work)){+.+.}-{0:0}, at: __flush_work+0x74/0x4e0
but task is already holding lock:
ffff8884a1808cc0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_ethtool_set_channels+0x53/0x200 [mlx5_core]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&priv->state_lock){+.+.}-{3:3}:
__mutex_lock+0x80/0xc90
arfs_handle_work+0x4b/0x3b0 [mlx5_core]
process_one_work+0x1dc/0x4a0
worker_thread+0x1bf/0x3c0
kthread+0xd7/0x100
ret_from_fork+0x2d/0x50
ret_from_fork_asm+0x11/0x20
-> #0 ((work_completion)(&rule->arfs_work)){+.+.}-{0:0}:
__lock_acquire+0x17b4/0x2c80
lock_acquire+0xd0/0x2b0
__flush_work+0x7a/0x4e0
__cancel_work_timer+0x131/0x1c0
arfs_del_rules+0x143/0x1e0 [mlx5_core]
mlx5e_arfs_disable+0x1b/0x30 [mlx5_core]
mlx5e_ethtool_set_channels+0xcb/0x200 [mlx5_core]
ethnl_set_channels+0x28f/0x3b0
ethnl_default_set_doit+0xec/0x240
genl_family_rcv_msg_doit+0xd0/0x120
genl_rcv_msg+0x188/0x2c0
netlink_rcv_skb+0x54/0x100
genl_rcv+0x24/0x40
netlink_unicast+0x1a1/0x270
netlink_sendmsg+0x214/0x460
__sock_sendmsg+0x38/0x60
__sys_sendto+0x113/0x170
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x46/0x4e
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&priv->state_lock);
lock((work_completion)(&rule->arfs_work));
lock(&priv->state_lock);
lock((work_completion)(&rule->arfs_work));
*** DEADLOCK ***
3 locks held by ethtool/386089:
#0: ffffffff82ea7210 (cb_lock){++++}-{3:3}, at: genl_rcv+0x15/0x40
#1: ffffffff82e94c88 (rtnl_mutex){+.+.}-{3:3}, at: ethnl_default_set_doit+0xd3/0x240
#2: ffff8884a1808cc0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_ethtool_set_channels+0x53/0x200 [mlx5_core]
stack backtrace:
CPU: 15 PID: 386089 Comm: ethtool Tainted: G I 6.7.0-rc4_net_next_mlx5_5483eb2 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x60/0xa0
check_noncircular+0x144/0x160
__lock_acquire+0x17b4/0x2c80
lock_acquire+0xd0/0x2b0
? __flush_work+0x74/0x4e0
? save_trace+0x3e/0x360
? __flush_work+0x74/0x4e0
__flush_work+0x7a/0x4e0
? __flush_work+0x74/0x4e0
? __lock_acquire+0xa78/0x2c80
? lock_acquire+0xd0/0x2b0
? mark_held_locks+0x49/0x70
__cancel_work_timer+0x131/0x1c0
? mark_held_locks+0x49/0x70
arfs_del_rules+0x143/0x1e0 [mlx5_core]
mlx5e_arfs_disable+0x1b/0x30 [mlx5_core]
mlx5e_ethtool_set_channels+0xcb/0x200 [mlx5_core]
ethnl_set_channels+0x28f/0x3b0
ethnl_default_set_doit+0xec/0x240
genl_family_rcv_msg_doit+0xd0/0x120
genl_rcv_msg+0x188/0x2c0
? ethnl_ops_begin+0xb0/0xb0
? genl_family_rcv_msg_dumpit+0xf0/0xf0
netlink_rcv_skb+0x54/0x100
genl_rcv+0x24/0x40
netlink_unicast+0x1a1/0x270
netlink_sendmsg+0x214/0x460
__sock_sendmsg+0x38/0x60
__sys_sendto+0x113/0x170
? do_user_addr_fault+0x53f/0x8f0
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x46/0x4e
</TASK>
Fixes: 45bf454ae8 ("net/mlx5e: Enabling aRFS mechanism")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240411115444.374475-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37cc10da3a ]
The cited patch introduces the concept of buckets in LAG in hash mode.
However, the patch doesn't clear the number of buckets in the LAG
deactivation. This results in using the wrong number of buckets in
case user create a hash mode LAG and afterwards create a non-hash
mode LAG.
Hence, restore buckets number to default after hash mode LAG
deactivation.
Fixes: 352899f384 ("net/mlx5: Lag, use buckets in hash mode")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240411115444.374475-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 56f78615bc upstream.
After the commit d2689b6a86 ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset operation, in which the default mac
address from the device is read, is not executed from bind operation and
the random address, that is pregenerated just in case, is direclty written
the first time in the device, so the default one from the device is not
even read. This writing is not dangerous because is volatile and the
default mac address is not missed.
In order to avoid this and keep the simplification to have only one
reset and reduce the delays, restore the reset from bind operation and
remove the reset that is commanded from open operation. The behavior is
the same but everything is ready for usbnet_probe.
Tested with ASIX AX88179 USB Gigabit Ethernet devices.
Restore the old behavior for the rest of possible devices because I don't
have the hardware to test.
cc: stable@vger.kernel.org # 6.6+
Fixes: d2689b6a86 ("net: usb: ax88179_178a: avoid two consecutive device resets")
Reported-by: Jarkko Palviainen <jarkko.palviainen@gmail.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20240417085524.219532-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf02d9fe00 ]
ENA has two types of TX queues:
- queues which only process TX packets arriving from the network stack
- queues which only process TX packets forwarded to it by XDP_REDIRECT
or XDP_TX instructions
The ena_free_tx_bufs() cycles through all descriptors in a TX queue
and unmaps + frees every descriptor that hasn't been acknowledged yet
by the device (uncompleted TX transactions).
The function assumes that the processed TX queue is necessarily from
the first category listed above and ends up using napi_consume_skb()
for descriptors belonging to an XDP specific queue.
This patch solves a bug in which, in case of a VF reset, the
descriptors aren't freed correctly, leading to crashes.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7e4171806 ]
Missing IO completions check is called every second (HZ jiffies).
This commit fixes several issues with this check:
1. Duplicate queues check:
Max of 4 queues are scanned on each check due to monitor budget.
Once reaching the budget, this check exits under the assumption that
the next check will continue to scan the remainder of the queues,
but in practice, next check will first scan the last already scanned
queue which is not necessary and may cause the full queue scan to
last a couple of seconds longer.
The fix is to start every check with the next queue to scan.
For example, on 8 IO queues:
Bug: [0,1,2,3], [3,4,5,6], [6,7]
Fix: [0,1,2,3], [4,5,6,7]
2. Unbalanced queues check:
In case the number of active IO queues is not a multiple of budget,
there will be checks which don't utilize the full budget
because the full scan exits when reaching the last queue id.
The fix is to run every TX completion check with exact queue budget
regardless of the queue id.
For example, on 7 IO queues:
Bug: [0,1,2,3], [4,5,6], [0,1,2,3]
Fix: [0,1,2,3], [4,5,6,0], [1,2,3,4]
The budget may be lowered in case the number of IO queues is less
than the budget (4) to make sure there are no duplicate queues on
the same check.
For example, on 3 IO queues:
Bug: [0,1,2,0], [1,2,0,1]
Fix: [0,1,2], [0,1,2]
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Amit Bernstein <amitbern@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 713a85195a ]
Small unsigned types are promoted to larger signed types in
the case of multiplication, the result of which may overflow.
In case the result of such a multiplication has its MSB
turned on, it will be sign extended with '1's.
This changes the multiplication result.
Code example of the phenomenon:
-------------------------------
u16 x, y;
size_t z1, z2;
x = y = 0xffff;
printk("x=%x y=%x\n",x,y);
z1 = x*y;
z2 = (size_t)x*y;
printk("z1=%lx z2=%lx\n", z1, z2);
Output:
-------
x=ffff y=ffff
z1=fffffffffffe0001 z2=fffe0001
The expected result of ffff*ffff is fffe0001, and without the
explicit casting to avoid the unwanted sign extension we got
fffffffffffe0001.
This commit adds an explicit casting to avoid the sign extension
issue.
Fixes: 689b2bdaaa ("net: ena: add functions for handling Low Latency Queues in ena_com")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17c5601132 ]
In Clause 5 of IEEE Std 802-2014, two sublayers of the data link layer
(DLL) of the Open Systems Interconnection basic reference model (OSI/RM)
are described; the medium access control (MAC) and logical link control
(LLC) sublayers. The MAC sublayer is the one facing the physical layer.
In 8.2 of IEEE Std 802.1Q-2022, the Bridge architecture is described. A
Bridge component comprises a MAC Relay Entity for interconnecting the Ports
of the Bridge, at least two Ports, and higher layer entities with at least
a Spanning Tree Protocol Entity included.
Each Bridge Port also functions as an end station and shall provide the MAC
Service to an LLC Entity. Each instance of the MAC Service is provided to a
distinct LLC Entity that supports protocol identification, multiplexing,
and demultiplexing, for protocol data unit (PDU) transmission and reception
by one or more higher layer entities.
It is described in 8.13.9 of IEEE Std 802.1Q-2022 that in a Bridge, the LLC
Entity associated with each Bridge Port is modeled as being directly
connected to the attached Local Area Network (LAN).
On the switch with CPU port architecture, CPU port functions as Management
Port, and the Management Port functionality is provided by software which
functions as an end station. Software is connected to an IEEE 802 LAN that
is wholly contained within the system that incorporates the Bridge.
Software provides access to the LLC Entity associated with each Bridge Port
by the value of the source port field on the special tag on the frame
received by software.
We call frames that carry control information to determine the active
topology and current extent of each Virtual Local Area Network (VLAN),
i.e., spanning tree or Shortest Path Bridging (SPB) and Multiple VLAN
Registration Protocol Data Units (MVRPDUs), and frames from other link
constrained protocols, such as Extensible Authentication Protocol over LAN
(EAPOL) and Link Layer Discovery Protocol (LLDP), link-local frames. They
are not forwarded by a Bridge. Permanently configured entries in the
filtering database (FDB) ensure that such frames are discarded by the
Forwarding Process. In 8.6.3 of IEEE Std 802.1Q-2022, this is described in
detail:
Each of the reserved MAC addresses specified in Table 8-1
(01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]) shall be
permanently configured in the FDB in C-VLAN components and ERs.
Each of the reserved MAC addresses specified in Table 8-2
(01-80-C2-00-00-[01,02,03,04,05,06,07,08,09,0A,0E]) shall be permanently
configured in the FDB in S-VLAN components.
Each of the reserved MAC addresses specified in Table 8-3
(01-80-C2-00-00-[01,02,04,0E]) shall be permanently configured in the FDB
in TPMR components.
The FDB entries for reserved MAC addresses shall specify filtering for all
Bridge Ports and all VIDs. Management shall not provide the capability to
modify or remove entries for reserved MAC addresses.
The addresses in Table 8-1, Table 8-2, and Table 8-3 determine the scope of
propagation of PDUs within a Bridged Network, as follows:
The Nearest Bridge group address (01-80-C2-00-00-0E) is an address that
no conformant Two-Port MAC Relay (TPMR) component, Service VLAN (S-VLAN)
component, Customer VLAN (C-VLAN) component, or MAC Bridge can forward.
PDUs transmitted using this destination address, or any other addresses
that appear in Table 8-1, Table 8-2, and Table 8-3
(01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]), can
therefore travel no further than those stations that can be reached via a
single individual LAN from the originating station.
The Nearest non-TPMR Bridge group address (01-80-C2-00-00-03), is an
address that no conformant S-VLAN component, C-VLAN component, or MAC
Bridge can forward; however, this address is relayed by a TPMR component.
PDUs using this destination address, or any of the other addresses that
appear in both Table 8-1 and Table 8-2 but not in Table 8-3
(01-80-C2-00-00-[00,03,05,06,07,08,09,0A,0B,0C,0D,0F]), will be relayed
by any TPMRs but will propagate no further than the nearest S-VLAN
component, C-VLAN component, or MAC Bridge.
The Nearest Customer Bridge group address (01-80-C2-00-00-00) is an
address that no conformant C-VLAN component, MAC Bridge can forward;
however, it is relayed by TPMR components and S-VLAN components. PDUs
using this destination address, or any of the other addresses that appear
in Table 8-1 but not in either Table 8-2 or Table 8-3
(01-80-C2-00-00-[00,0B,0C,0D,0F]), will be relayed by TPMR components and
S-VLAN components but will propagate no further than the nearest C-VLAN
component or MAC Bridge.
Because the LLC Entity associated with each Bridge Port is provided via CPU
port, we must not filter these frames but forward them to CPU port.
In a Bridge, the transmission Port is majorly decided by ingress and egress
rules, FDB, and spanning tree Port State functions of the Forwarding
Process. For link-local frames, only CPU port should be designated as
destination port in the FDB, and the other functions of the Forwarding
Process must not interfere with the decision of the transmission Port. We
call this process trapping frames to CPU port.
Therefore, on the switch with CPU port architecture, link-local frames must
be trapped to CPU port, and certain link-local frames received by a Port of
a Bridge comprising a TPMR component or an S-VLAN component must be
excluded from it.
A Bridge of the switch with CPU port architecture cannot comprise a
Two-Port MAC Relay (TPMR) component as a TPMR component supports only a
subset of the functionality of a MAC Bridge. A Bridge comprising two Ports
(Management Port doesn't count) of this architecture will either function
as a standard MAC Bridge or a standard VLAN Bridge.
Therefore, a Bridge of this architecture can only comprise S-VLAN
components, C-VLAN components, or MAC Bridge components. Since there's no
TPMR component, we don't need to relay PDUs using the destination addresses
specified on the Nearest non-TPMR section, and the proportion of the
Nearest Customer Bridge section where they must be relayed by TPMR
components.
One option to trap link-local frames to CPU port is to add static FDB
entries with CPU port designated as destination port. However, because that
Independent VLAN Learning (IVL) is being used on every VID, each entry only
applies to a single VLAN Identifier (VID). For a Bridge comprising a MAC
Bridge component or a C-VLAN component, there would have to be 16 times
4096 entries. This switch intellectual property can only hold a maximum of
2048 entries. Using this option, there also isn't a mechanism to prevent
link-local frames from being discarded when the spanning tree Port State of
the reception Port is discarding.
The remaining option is to utilise the BPC, RGAC1, RGAC2, RGAC3, and RGAC4
registers. Whilst this applies to every VID, it doesn't contain all of the
reserved MAC addresses without affecting the remaining Standard Group MAC
Addresses. The REV_UN frame tag utilised using the RGAC4 register covers
the remaining 01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F] destination
addresses. It also includes the 01-80-C2-00-00-22 to 01-80-C2-00-00-FF
destination addresses which may be relayed by MAC Bridges or VLAN Bridges.
The latter option provides better but not complete conformance.
This switch intellectual property also does not provide a mechanism to trap
link-local frames with specific destination addresses to CPU port by
Bridge, to conform to the filtering rules for the distinct Bridge
components.
Therefore, regardless of the type of the Bridge component, link-local
frames with these destination addresses will be trapped to CPU port:
01-80-C2-00-00-[00,01,02,03,0E]
In a Bridge comprising a MAC Bridge component or a C-VLAN component:
Link-local frames with these destination addresses won't be trapped to
CPU port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F]
In a Bridge comprising an S-VLAN component:
Link-local frames with these destination addresses will be trapped to CPU
port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-00
Link-local frames with these destination addresses won't be trapped to
CPU port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-[04,05,06,07,08,09,0A]
Currently on this switch intellectual property, if the spanning tree Port
State of the reception Port is discarding, link-local frames will be
discarded.
To trap link-local frames regardless of the spanning tree Port State, make
the switch regard them as Bridge Protocol Data Units (BPDUs). This switch
intellectual property only lets the frames regarded as BPDUs bypass the
spanning tree Port State function of the Forwarding Process.
With this change, the only remaining interference is the ingress rules.
When the reception Port has no PVID assigned on software, VLAN-untagged
frames won't be allowed in. There doesn't seem to be a mechanism on the
switch intellectual property to have link-local frames bypass this function
of the Forwarding Process.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240409-b4-for-net-mt7530-fix-link-local-when-stp-discarding-v2-1-07b1150164ac@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33623113a4 ]
The wrong port config is being used if the PCS is reconfigured. Fix this
by correctly using the new config instead of the old one.
Fixes: 946e7fd505 ("net: sparx5: add port module support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240409-link-mode-reconfiguration-fix-v2-1-db6a507f3627@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f436f1869 ]
When creating a new HTB class while the interface is down,
the variable that follows the number of QoS SQs (htb_max_qos_sqs)
may not be consistent with the number of HTB classes.
Previously, we compared these two values to ensure that
the node_qid is lower than the number of QoS SQs, and we
allocated stats for that SQ when they are equal.
Change the check to compare the node_qid with the current
number of leaf nodes and fix the checking conditions to
ensure allocation of stats_list and stats for each node.
Fixes: 214baf2287 ("net/mlx5e: Support HTB offload")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-9-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c6782ad49 ]
Previously, add_rule_fg would only add newly created rules from the
handle into the tree when they had a refcount of 1. On the other hand,
create_flow_handle tries hard to find and reference already existing
identical rules instead of creating new ones.
These two behaviors can result in a situation where create_flow_handle
1) creates a new rule and references it, then
2) in a subsequent step during the same handle creation references it
again,
resulting in a rule with a refcount of 2 that is not linked into the
tree, will have a NULL parent and root and will result in a crash when
the flow group is deleted because del_sw_hw_rule, invoked on rule
deletion, assumes node->parent is != NULL.
This happened in the wild, due to another bug related to incorrect
handling of duplicate pkt_reformat ids, which lead to the code in
create_flow_handle incorrectly referencing a just-added rule in the same
flow handle, resulting in the problem described above. Full details are
at [1].
This patch changes add_rule_fg to add new rules without parents into
the tree, properly initializing them and avoiding the crash. This makes
it more consistent with how rules are added to an FTE in
create_flow_handle.
Fixes: 74491de937 ("net/mlx5: Add multi dest support")
Link: https://lore.kernel.org/netdev/ea5264d6-6b55-4449-a602-214c6f509c1e@163.com/T/#u [1]
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faf2300618 ]
NIX SQ mode and link backpressure configuration is required for
all platforms. But in current driver this code is wrongly placed
under specific platform check. This patch fixes the issue by
moving the code out of platform check.
Fixes: 5d9b976d44 ("octeontx2-af: Support fixed transmit scheduler topology")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20240408063643.26288-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be0384bf59 ]
The ks8851_irq() thread may call ks8851_rx_pkts() in case there are
any packets in the MAC FIFO, which calls netif_rx(). This netif_rx()
implementation is guarded by local_bh_disable() and local_bh_enable().
The local_bh_enable() may call do_softirq() to run softirqs in case
any are pending. One of the softirqs is net_rx_action, which ultimately
reaches the driver .start_xmit callback. If that happens, the system
hangs. The entire call chain is below:
ks8851_start_xmit_par from netdev_start_xmit
netdev_start_xmit from dev_hard_start_xmit
dev_hard_start_xmit from sch_direct_xmit
sch_direct_xmit from __dev_queue_xmit
__dev_queue_xmit from __neigh_update
__neigh_update from neigh_update
neigh_update from arp_process.constprop.0
arp_process.constprop.0 from __netif_receive_skb_one_core
__netif_receive_skb_one_core from process_backlog
process_backlog from __napi_poll.constprop.0
__napi_poll.constprop.0 from net_rx_action
net_rx_action from __do_softirq
__do_softirq from call_with_stack
call_with_stack from do_softirq
do_softirq from __local_bh_enable_ip
__local_bh_enable_ip from netif_rx
netif_rx from ks8851_irq
ks8851_irq from irq_thread_fn
irq_thread_fn from irq_thread
irq_thread from kthread
kthread from ret_from_fork
The hang happens because ks8851_irq() first locks a spinlock in
ks8851_par.c ks8851_lock_par() spin_lock_irqsave(&ksp->lock, ...)
and with that spinlock locked, calls netif_rx(). Once the execution
reaches ks8851_start_xmit_par(), it calls ks8851_lock_par() again
which attempts to claim the already locked spinlock again, and the
hang happens.
Move the do_softirq() call outside of the spinlock protected section
of ks8851_irq() by disabling BHs around the entire spinlock protected
section of ks8851_irq() handler. Place local_bh_enable() outside of
the spinlock protected section, so that it can trigger do_softirq()
without the ks8851_par.c ks8851_lock_par() spinlock being held, and
safely call ks8851_start_xmit_par() without attempting to lock the
already locked spinlock.
Since ks8851_irq() is protected by local_bh_disable()/local_bh_enable()
now, replace netif_rx() with __netif_rx() which is not duplicating the
local_bh_disable()/local_bh_enable() calls.
Fixes: 797047f875 ("net: ks8851: Implement Parallel bus operations")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240405203204.82062-2-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f96f700449 ]
Both ks8851_rx_skb_par() and ks8851_rx_skb_spi() call netif_rx(skb),
inline the netif_rx(skb) call directly into ks8851_common.c and drop
the .rx_skb callback and ks8851_rx_skb() wrapper. This removes one
indirect call from the driver, no functional change otherwise.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240405203204.82062-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: be0384bf59 ("net: ks8851: Handle softirqs at the end of IRQ thread to fix hang")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faa12ca245 ]
It is possible that during error recovery and firmware reset,
there is a pending TX PTP packet waiting for the timestamp.
We need to reset this condition so that after recovery, the
tx_avail count for PTP is reset back to the initial value.
Otherwise, we may not accept any PTP TX timestamps after
recovery.
Fixes: 118612d519 ("bnxt_en: Add PTP clock APIs, ioctls, and ethtool methods")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8a6213d70 ]
syzbot is able to trigger an uninit-value in geneve_xmit() [1]
Problem : While most ip tunnel helpers (like ip_tunnel_get_dsfield())
uses skb_protocol(skb, true), pskb_inet_may_pull() is only using
skb->protocol.
If anything else than ETH_P_IPV6 or ETH_P_IP is found in skb->protocol,
pskb_inet_may_pull() does nothing at all.
If a vlan tag was provided by the caller (af_packet in the syzbot case),
the network header might not point to the correct location, and skb
linear part could be smaller than expected.
Add skb_vlan_inet_prepare() to perform a complete mac validation.
Use this in geneve for the moment, I suspect we need to adopt this
more broadly.
v4 - Jakub reported v3 broke l2_tos_ttl_inherit.sh selftest
- Only call __vlan_get_protocol() for vlan types.
Link: https://lore.kernel.org/netdev/20240404100035.3270a7d5@kernel.org/
v2,v3 - Addressed Sabrina comments on v1 and v2
Link: https://lore.kernel.org/netdev/Zg1l9L2BNoZWZDZG@hog/
[1]
BUG: KMSAN: uninit-value in geneve_xmit_skb drivers/net/geneve.c:910 [inline]
BUG: KMSAN: uninit-value in geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030
geneve_xmit_skb drivers/net/geneve.c:910 [inline]
geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030
__netdev_start_xmit include/linux/netdevice.h:4903 [inline]
netdev_start_xmit include/linux/netdevice.h:4917 [inline]
xmit_one net/core/dev.c:3531 [inline]
dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3547
__dev_queue_xmit+0x348d/0x52c0 net/core/dev.c:4335
dev_queue_xmit include/linux/netdevice.h:3091 [inline]
packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3081 [inline]
packet_sendmsg+0x8bb0/0x9ef0 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x30f/0x380 net/socket.c:745
__sys_sendto+0x685/0x830 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x125/0x1d0 net/socket.c:2199
do_syscall_64+0xd5/0x1f0
entry_SYSCALL_64_after_hwframe+0x6d/0x75
Uninit was created at:
slab_post_alloc_hook mm/slub.c:3804 [inline]
slab_alloc_node mm/slub.c:3845 [inline]
kmem_cache_alloc_node+0x613/0xc50 mm/slub.c:3888
kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:577
__alloc_skb+0x35b/0x7a0 net/core/skbuff.c:668
alloc_skb include/linux/skbuff.h:1318 [inline]
alloc_skb_with_frags+0xc8/0xbf0 net/core/skbuff.c:6504
sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2795
packet_alloc_skb net/packet/af_packet.c:2930 [inline]
packet_snd net/packet/af_packet.c:3024 [inline]
packet_sendmsg+0x722d/0x9ef0 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x30f/0x380 net/socket.c:745
__sys_sendto+0x685/0x830 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x125/0x1d0 net/socket.c:2199
do_syscall_64+0xd5/0x1f0
entry_SYSCALL_64_after_hwframe+0x6d/0x75
CPU: 0 PID: 5033 Comm: syz-executor346 Not tainted 6.9.0-rc1-syzkaller-00005-g928a87efa423 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024
Fixes: d13f048dd4 ("net: geneve: modify IP header check in geneve6_xmit_skb and geneve_xmit_skb")
Reported-by: syzbot+9ee20ec1de7b3168db09@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/000000000000d19c3a06152f9ee4@google.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Phillip Potter <phil@philpotter.co.uk>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11fbb1bfb5 ]
When initializing over virtchnl, the PF is required to pass a VSI ID to the
VF as part of its capabilities exchange. The VF driver reports this value
back to the PF in a variety of commands. The PF driver validates that this
value matches the value it sent to the VF.
Some hardware families such as the E700 series could use this value when
reading RSS registers or communicating directly with firmware over the
Admin Queue.
However, E800 series hardware does not support any of these interfaces and
the VF's only use for this value is to report it back to the PF. Thus,
there is no requirement that this value be an actual VSI ID value of any
kind.
The PF driver already does not trust that the VF sends it a real VSI ID.
The VSI structure is always looked up from the VF structure. The PF does
validate that the VSI ID provided matches a VSI associated with the VF, but
otherwise does not use the VSI ID for any purpose.
Instead of reporting the VSI number relative to the PF space, report a
fixed value of 1. When communicating with the VF over virtchnl, validate
that the VSI number is returned appropriately.
This avoids leaking information about the firmware of the PF state.
Currently the ice driver only supplies a VF with a single VSI. However, it
appears that virtchnl has some support for allowing multiple VSIs. I did
not attempt to implement this. However, space is left open to allow further
relative indexes if additional VSIs are provided in future feature
development. For this reason, keep the ice_vc_isvalid_vsi_id function in
place to allow extending it for multiple VSIs in the future.
This change will also simplify handling of live migration in a future
series. Since we no longer will provide a real VSI number to the VF, there
will be no need to keep track of this number when migrating to a new host.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cca1bddf9 ]
Currently buf_len field of ath11k_mhi_config_qca6390 is assigned
with 0, making MHI use a default size, 64KB, to allocate channel
buffers. This is likely to fail in some scenarios where system
memory is highly fragmented and memory compaction or reclaim is
not allowed.
There is a fail report which is caused by it:
kworker/u32:45: page allocation failure: order:4, mode:0x40c00(GFP_NOIO|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
CPU: 0 PID: 19318 Comm: kworker/u32:45 Not tainted 6.8.0-rc3-1.gae4495f-default #1 openSUSE Tumbleweed (unreleased) 493b6d5b382c603654d7a81fc3c144d59a1dfceb
Workqueue: events_unbound async_run_entry_fn
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x60
warn_alloc+0x13a/0x1b0
? srso_alias_return_thunk+0x5/0xfbef5
? __alloc_pages_direct_compact+0xab/0x210
__alloc_pages_slowpath.constprop.0+0xd3e/0xda0
__alloc_pages+0x32d/0x350
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__kmalloc_large_node+0x72/0x110
__kmalloc+0x37c/0x480
? mhi_map_single_no_bb+0x77/0xf0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__mhi_prepare_for_transfer+0x44/0x80 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? __pfx_____mhi_prepare_for_transfer+0x10/0x10 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
device_for_each_child+0x5c/0xa0
? __pfx_pci_pm_resume+0x10/0x10
ath11k_core_resume+0x65/0x100 [ath11k a5094e22d7223135c40d93c8f5321cf09fd85e4e]
? srso_alias_return_thunk+0x5/0xfbef5
ath11k_pci_pm_resume+0x32/0x60 [ath11k_pci 830b7bfc3ea80ebef32e563cafe2cb55e9cc73ec]
? srso_alias_return_thunk+0x5/0xfbef5
dpm_run_callback+0x8c/0x1e0
device_resume+0x104/0x340
? __pfx_dpm_watchdog_handler+0x10/0x10
async_resume+0x1d/0x30
async_run_entry_fn+0x32/0x120
process_one_work+0x168/0x330
worker_thread+0x2f5/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe8/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Actually those buffers are used only by QMI target -> host communication.
And for WCN6855 and QCA6390, the largest packet size for that is less
than 6KB. So change buf_len field to 8KB, which results in order 1
allocation if page size is 4KB. In this way, we can at least save some
memory, and as well as decrease the possibility of allocation failure
in those scenarios.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Closes: https://lore.kernel.org/ath11k/96481a45-3547-4d23-ad34-3a8f1d90c1cd@suse.cz/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223053111.29170-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5151005d3 ]
In particular the xpcs_soft_reset() and xpcs_do_config() functions
currently return -1 if invalid auto-negotiation mode is specified. That
value might be then passed to the generic kernel subsystems which require
a standard kernel errno value. Even though the erroneous conditions are
very specific (memory corruption or buggy driver implementation) using a
hard-coded -1 literal doesn't seem correct anyway especially when it comes
to passing it higher to the network subsystem or printing to the system
log. Convert the hard-coded error values to -EINVAL then.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32167707aa ]
The ACEPC W5 Pro HDMI stick contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.$(DEFAULT_STRING)-$(DEFAULT_STRING).txt" as nvram file
which is both too generic and messy with the $ symbols in the name.
The ACEPC W5 Pro uses the same Ampak AP6255 module as the ACEPC T8
and the nvram for the T8 is already in linux-firmware, so point the new
DMI nvram filename quirk to the T8 nvram file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240216213649.251718-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c699f35d65 ]
We claim to have the AdminQ on our irq0 and thus cpu id 0,
but we need to be sure we set the affinity hint to try to
keep it there.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c108b4a50d ]
Hardware puts RX descriptor and packet in RX DMA buffer, so it could be
over one buffer size if packet size is 11454, and then it will be split
into two segments. WiFi 7 chips use larger size of RX descriptor, so
enlarge DMA buffer size according to RX descriptor to have better
performance and simple flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-5-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5642c82b94 ]
A potential string truncation was reported in bnx2x_fill_fw_str(),
when a long bp->fw_ver and a long phy_fw_ver might coexist, but seems
unlikely with real-world hardware.
Use scnprintf() to indicate the intent that truncations are tolerated.
While reading this code, I found a collection of various buffer size
counting issues. None looked like they might lead to a buffer overflow
with current code (the small buffers are 20 bytes and might only ever
consume 10 bytes twice with a trailing %NUL). However, early truncation
(due to a %NUL in the middle of the string) might be happening under
likely rare conditions. Regardless fix the formatters and related
functions:
- Switch from a separate strscpy() to just adding an additional "%s" to
the format string that immediately follows it in bnx2x_fill_fw_str().
- Use sizeof() universally instead of using unbound defines.
- Fix bnx2x_7101_format_ver() and bnx2x_null_format_ver() to report the
number of characters written, not including the trailing %NUL (as
already done with the other firmware formatting functions).
- Require space for at least 1 byte in bnx2x_get_ext_phy_fw_version()
for the trailing %NUL.
- Correct the needed buffer size in bnx2x_3_seq_format_ver().
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401260858.jZN6vD1k-lkp@intel.com/
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240126041044.work.220-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6b27eb997 ]
In 'ath_ant_try_scan()', (most likely) the 2nd LNA's signal
strength should be used in comparison against RSSI when
selecting first LNA as the main one. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231211172502.25202-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 101b76418d ]
The error statistics should be updated each time the poll function is
called, even if the full RX work budget has been consumed. This prevents
the counts from becoming stuck when RX bandwidth usage is high.
This also ensures that error counters are not updated after we've
re-enabled interrupts as that could result in a race condition.
Also drop an unnecessary space.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20240402145305.82148-2-paul.barker.ct@bp.renesas.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 596a425491 ]
The TX queue should be serviced each time the poll function is called,
even if the full RX work budget has been consumed. This prevents
starvation of the TX queue when RX bandwidth usage is high.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20240402145305.82148-1-paul.barker.ct@bp.renesas.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b993bfdb4 ]
ravb_poll() initial code used to interrogate the first descriptor of the
RX queue in case gPTP is false to determine if ravb_rx() should be called.
This is done for non-gPTP IPs. For gPTP IPs the driver PTP-specific
information was used to determine if receive function should be called. As
every IP has its own receive function that interrogates the RX descriptors
list in the same way the ravb_poll() was doing there is no need to double
check this in ravb_poll(). Removing the code from ravb_poll() leads to a
cleaner code.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 596a425491 ("net: ravb: Always process TX descriptor ring")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbc17e7802 ]
Setting mac_managed_pm during interface up is too late.
In situations where the link is not brought up yet and the system suspends
the regular PHY power management will run. Since the FEC ETHEREN control
bit is cleared (automatically) on suspend the controller is off in resume.
When the regular PHY power management resume path runs in this context it
will write to the MII_DATA register but nothing will be transmitted on the
MDIO bus.
This can be observed by the following log:
fec 5b040000.ethernet eth0: MDIO read timeout
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: dpm_run_callback(): mdio_bus_phy_resume+0x0/0xc8 returns -110
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: failed to resume: error -110
The data written will however remain in the MII_DATA register.
When the link later is set to administrative up it will trigger a call to
fec_restart() which will restore the MII_SPEED register. This triggers the
quirk explained in f166f890c8 ("net: ethernet: fec: Replace interrupt
driven MDIO with polled IO") causing an extra MII_EVENT.
This extra event desynchronizes all the MDIO register reads, causing them
to complete too early. Leading all reads to read as 0 because
fec_enet_mdio_wait() returns too early.
When a Microchip LAN8700R PHY is connected to the FEC, the 0 reads causes
the PHY to be initialized incorrectly and the PHY will not transmit any
ethernet signal in this state. It cannot be brought out of this state
without a power cycle of the PHY.
Fixes: 557d5dc83f ("net: fec: use mac-managed PHY PM")
Closes: https://lore.kernel.org/netdev/1f45bdbe-eab1-4e59-8f24-add177590d27@actia.se/
Signed-off-by: Wei Fang <wei.fang@nxp.com>
[jernberg: commit message]
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://lore.kernel.org/r/20240328155909.59613-2-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eca485d221 ]
Signed-off-by: Dennis Kirjanov <dkirjanov@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: cbc17e7802 ("net: fec: Set mac_managed_pm during probe")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49ef7d846d ]
Bail out if the function is used with chip versions that don't support
ASPM configuration. In addition remove the delay, it tuned out that
it's not needed, also vendor driver r8125 doesn't have it.
Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5e864d90b2 ("r8169: skip DASH fw status checks when DASH is disabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bc6c4e689 ]
For disabling ASPM during NAPI poll we'll have to access both registers
in atomic context. Use a spinlock to protect access.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5e864d90b2 ("r8169: skip DASH fw status checks when DASH is disabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91c8643578 ]
For disabling ASPM during NAPI poll we'll have to access mac ocp
registers in atomic context. This could result in races because
a mac ocp read consists of a write to register OCPDR, followed
by a read from the same register. Therefore add a spinlock to
protect access to mac ocp registers.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5e864d90b2 ("r8169: skip DASH fw status checks when DASH is disabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea558de723 ]
As for ice bug fixed by commit b7306b42be ("ice: manage interrupts
during poll exit") followed by commit 23be7075b3 ("ice: fix software
generating extra interrupts") I'm seeing the similar issue also with
i40e driver.
In certain situation when busy-loop is enabled together with adaptive
coalescing, the driver occasionally misses that there are outstanding
descriptors to clean when exiting busy poll.
Try to catch the remaining work by triggering a software interrupt
when exiting busy poll. No extra interrupts will be generated when
busy polling is not used.
The issue was found when running sockperf ping-pong tcp test with
adaptive coalescing and busy poll enabled (50 as value busy_pool
and busy_read sysctl knobs) and results in huge latency spikes
with more than 100000us.
The fix is inspired from the ice driver and do the following:
1) During napi poll exit in case of busy-poll (napo_complete_done()
returns false) this is recorded to q_vector that we were in busy
loop.
2) Extends i40e_buildreg_itr() to be able to add an enforced software
interrupt into built value
2) In i40e_update_enable_itr() enforces a software interrupt trigger
if we are exiting busy poll to catch any pending clean-ups
3) Reuses unused 3rd ITR (interrupt throttle) index and set it to
20K interrupts per second to limit the number of these sw interrupts.
Test results
============
Prior:
[root@dell-per640-07 net]# sockperf ping-pong -i 10.9.9.1 --tcp -m 1000 --mps=max -t 120
sockperf: == version #3.10-no.git ==
sockperf[CLIENT] send on:sockperf: using recvfrom() to block on socket(s)
[ 0] IP = 10.9.9.1 PORT = 11111 # TCP
sockperf: Warmup stage (sending a few dummy messages)...
sockperf: Starting test...
sockperf: Test end (interrupted by timer)
sockperf: Test ended
sockperf: [Total Run] RunTime=119.999 sec; Warm up time=400 msec; SentMessages=2438563; ReceivedMessages=2438562
sockperf: ========= Printing statistics for Server No: 0
sockperf: [Valid Duration] RunTime=119.549 sec; SentMessages=2429473; ReceivedMessages=2429473
sockperf: ====> avg-latency=24.571 (std-dev=93.297, mean-ad=4.904, median-ad=1.510, siqr=1.063, cv=3.797, std-error=0.060, 99.0% ci=[24.417, 24.725])
sockperf: # dropped messages = 0; # duplicated messages = 0; # out-of-order messages = 0
sockperf: Summary: Latency is 24.571 usec
sockperf: Total 2429473 observations; each percentile contains 24294.73 observations
sockperf: ---> <MAX> observation = 103294.331
sockperf: ---> percentile 99.999 = 45.633
sockperf: ---> percentile 99.990 = 37.013
sockperf: ---> percentile 99.900 = 35.910
sockperf: ---> percentile 99.000 = 33.390
sockperf: ---> percentile 90.000 = 28.626
sockperf: ---> percentile 75.000 = 27.741
sockperf: ---> percentile 50.000 = 26.743
sockperf: ---> percentile 25.000 = 25.614
sockperf: ---> <MIN> observation = 12.220
After:
[root@dell-per640-07 net]# sockperf ping-pong -i 10.9.9.1 --tcp -m 1000 --mps=max -t 120
sockperf: == version #3.10-no.git ==
sockperf[CLIENT] send on:sockperf: using recvfrom() to block on socket(s)
[ 0] IP = 10.9.9.1 PORT = 11111 # TCP
sockperf: Warmup stage (sending a few dummy messages)...
sockperf: Starting test...
sockperf: Test end (interrupted by timer)
sockperf: Test ended
sockperf: [Total Run] RunTime=119.999 sec; Warm up time=400 msec; SentMessages=2400055; ReceivedMessages=2400054
sockperf: ========= Printing statistics for Server No: 0
sockperf: [Valid Duration] RunTime=119.549 sec; SentMessages=2391186; ReceivedMessages=2391186
sockperf: ====> avg-latency=24.965 (std-dev=5.934, mean-ad=4.642, median-ad=1.485, siqr=1.067, cv=0.238, std-error=0.004, 99.0% ci=[24.955, 24.975])
sockperf: # dropped messages = 0; # duplicated messages = 0; # out-of-order messages = 0
sockperf: Summary: Latency is 24.965 usec
sockperf: Total 2391186 observations; each percentile contains 23911.86 observations
sockperf: ---> <MAX> observation = 195.841
sockperf: ---> percentile 99.999 = 45.026
sockperf: ---> percentile 99.990 = 39.009
sockperf: ---> percentile 99.900 = 35.922
sockperf: ---> percentile 99.000 = 33.482
sockperf: ---> percentile 90.000 = 28.902
sockperf: ---> percentile 75.000 = 27.821
sockperf: ---> percentile 50.000 = 26.860
sockperf: ---> percentile 25.000 = 25.685
sockperf: ---> <MIN> observation = 12.277
Fixes: 0bcd952fee ("ethernet/intel: consolidate NAPI and NAPI exit")
Reported-by: Hugo Ferreira <hferreir@redhat.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit addca9175e ]
Enum type names should not be suffixed by '_t'. Either to use
'typedef enum name name_t' to so plain 'name_t var' instead of
'enum name_t var'.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-6-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: ea558de723 ("i40e: Enforce software interrupt during busy-poll exit")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b85a4f39f ]
Make it easy to figure out the IRQ number for a particular i40e_q_vector by
storing the assigned IRQ in the structure itself.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: ea558de723 ("i40e: Enforce software interrupt during busy-poll exit")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f37c4eac99 upstream.
To fix the regression introduced by commit 52424f974b, which causes
servers hang in very hard to reproduce conditions with resets races.
Using two sources for the information is the root cause.
In this function before the fix bumping v didn't mean bumping vf
pointer. But the code used this variables interchangeably, so stale vf
could point to different/not intended vf.
Remove redundant "v" variable and iterate via single VF pointer across
whole function instead to guarantee VF pointer validity.
Fixes: 52424f974b ("i40e: Fix VF hang when reset is triggered on another VF")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb58c598ce upstream.
The bug usually affects untrusted VFs, because they are limited to 18 MACs,
it affects them badly, not letting to create MAC all filters.
Not stable to reproduce, it happens when VF user creates MAC filters
when other MACVLAN operations are happened in parallel.
But consequence is that VF can't receive desired traffic.
Fix counter to be bumped only for new or active filters.
Fixes: 621650cabe ("i40e: Refactoring VF MAC filters counting to make more reliable")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef15ddeeb6 upstream.
In rvu_map_cgx_lmac_pf() the 'iter', which is used as an array index, can reach
value (up to 14) that exceed the size (MAX_LMAC_COUNT = 8) of the array.
Fix this bug by adding 'iter' value check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 91c6945ea1 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e709acbd84 upstream.
otx2_rxtx_enable() return negative error code such as -EIO,
check -EIO rather than EIO to fix this problem.
Fixes: c926252205 ("octeontx2-pf: Disable packet I/O for graceful exit")
Signed-off-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://lore.kernel.org/r/20240328020620.4054692-1-suhui@nfschina.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ba80d9658 upstream.
The current implementation for loading coalesced KPU profiles has
a limitation. The "offset" field, which is used to locate profiles
within the profile is restricted to a u16.
This restricts the number of profiles that can be loaded. This patch
addresses this limitation by increasing the size of the "offset" field.
Fixes: 11c730bfbf ("octeontx2-af: support for coalescing KPU profiles")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e864d90b2 upstream.
On devices that support DASH, the current code in the "rtl_loop_wait" function
raises false alarms when DASH is disabled. This occurs because the function
attempts to wait for the DASH firmware to be ready, even though it's not
relevant in this case.
r8169 0000:0c:00.0 eth0: RTL8168ep/8111ep, 38:7c:76:49:08:d9, XID 502, IRQ 86
r8169 0000:0c:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
r8169 0000:0c:00.0 eth0: DASH disabled
...
r8169 0000:0c:00.0 eth0: rtl_ep_ocp_read_cond == 0 (loop: 30, delay: 10000).
This patch modifies the driver start/stop functions to skip checking the DASH
firmware status when DASH is explicitly disabled. This prevents unnecessary
delays and false alarms.
The patch has been tested on several ThinkStation P8/PX workstations.
Fixes: 0ab0c45d8a ("r8169: add handling DASH when DASH is disabled")
Signed-off-by: Atlas Yu <atlas.yu@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20240328055152.18443-1-atlas.yu@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
