commit 0d5e2a8223 upstream
The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.
A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dbe5f1936 upstream
The ndo_set_rx_mode function is synchronized with the
netif_addr_lock spinlock and BHs disabled. Since this
function is also invoked directly from the driver the
same synchronization should be applied.
Fixes: 72f9634762 ("net: bcmgenet: set Rx mode before starting netif")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d85cf67a33 upstream
The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().
The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.
Fixes: afe3f907d2 ("net: bcmgenet: power on MII block for all MII modes")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 696450c051 upstream
Clear the RGMII_LINK bit upon detecting link down to be consistent with
setting the bit upon link up. We also move the clearing of the
out-of-band disable to the runtime initialization rather than for each
link up/down transition.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221118213754.1383364-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 35d92abfba ]
The devlink reload process will access the hardware resources,
but the register operation is done before the hardware is initialized.
So, processing the devlink reload during initialization may lead to kernel
crash.
This patch fixes this by registering the devlink after
hardware initialization.
Fixes: cd6242991d ("net: hns3: add support for registering devlink for VF")
Fixes: 93305b77ff ("net: hns3: fix kernel crash when devlink reload during pf initialization")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5db7a3b65 ]
According to hardware limitation, for device support modify
VLAN filter state but not support bypass port VLAN filter,
it should always disable the port VLAN filter. but the driver
enables port VLAN filter when initializing, if there is no
VLAN(except VLAN 0) id added, the driver will disable it
in service task. In most time, it works fine. But there is
a time window before the service task shceduled and net device
being registered. So if user adds VLAN at this time, the driver
will not update the VLAN filter state, and the port VLAN filter
remains enabled.
To fix the problem, if support modify VLAN filter state but not
support bypass port VLAN filter, set the port vlan filter to "off".
Fixes: 184cd221a8 ("net: hns3: disable port VLAN filter when support function level VLAN filter control")
Fixes: 2ba306627f ("net: hns3: add support for modify VLAN filter state")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 094c281228 ]
There is a memory barrier in followed case. When set the port down,
hclgevf_set_timmer will set DOWN in state. Meanwhile, the service task has
different behaviour based on whether the state is DOWN. Thus, to make sure
service task see DOWN, use smp_mb__after_atomic after calling set_bit().
CPU0 CPU1
========================== ===================================
hclgevf_set_timer_task() hclgevf_periodic_service_task()
set_bit(DOWN,state) test_bit(DOWN,state)
pf also has this issue.
Fixes: ff200099d2 ("net: hns3: remove unnecessary work in hclgevf_main")
Fixes: 1c6dfe6fc6 ("net: hns3: remove mailbox and reset work in hclge_main")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 950aa42399 ]
During the PF initialization process, hclge_update_port_info may return an
error code for some reason. At this point, the ptp initialization has been
completed. To void memory leaks, the resources that are applied by ptp
should be released. Therefore, when hclge_update_port_info returns an error
code, hclge_ptp_uninit is called to release the corresponding resources.
Fixes: eaf83ae59e ("net: hns3: add querying fec ability from firmware")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6639a7b953 ]
It provides nodemask_t to describe the numa node mask in kernel. To
improve transportability, change the type of numa_node_mask as nodemask_t.
Fixes: 38caee9d3e ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 669554c512 ]
Currently, the driver didn't return when receive a unknown
mailbox message, and continue checking whether need to
generate a response. It's unnecessary and may be incorrect.
Fixes: bb5790b71b ("net: hns3: refactor mailbox response scheme between PF and VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05eb60e964 ]
When a reset occurring, it's supposed to recover user's configuration.
Currently, the port info(speed, duplex and autoneg) is stored in hclge_mac
and will be scheduled updated. Consider the case that reset was happened
consecutively. During the first reset, the port info is configured with
a temporary value cause the PHY is reset and looking for best link config.
Second reset start and use pervious configuration which is not the user's.
The specific process is as follows:
+------+ +----+ +----+
| USER | | PF | | HW |
+---+--+ +-+--+ +-+--+
| ethtool --reset | |
+------------------->| reset command |
| ethtool --reset +-------------------->|
+------------------->| +---+
| +---+ | |
| | |reset currently | | HW RESET
| | |and wait to do | |
| |<--+ | |
| | send pervious cfg |<--+
| | (1000M FULL AN_ON) |
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | reset command |<--+
| +-------------------->|
| | +---+
| | send pervious cfg | | HW RESET
| | (10M HALF AN_OFF) |<--+
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | | |
| | read cfg(time task) |<--+
| | (10M HALF AN_OFF) |
| |<--------------------+
| | |
v v v
To avoid aboved situation, this patch introduced req_speed, req_duplex,
req_autoneg to store user's configuration and it only be used after
hardware reset and to recover user's configuration
Fixes: f5f2b3e4dc ("net: hns3: add support for imp-controlled PHYs")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0863634bf ]
Currently the driver uses local_bh_disable()/local_bh_enable() in its
IRQ handler to avoid triggering net_rx_action() softirq on exit from
netif_rx(). The net_rx_action() could trigger this driver .start_xmit
callback, which is protected by the same lock as the IRQ handler, so
calling the .start_xmit from netif_rx() from the IRQ handler critical
section protected by the lock could lead to an attempt to claim the
already claimed lock, and a hang.
The local_bh_disable()/local_bh_enable() approach works only in case
the IRQ handler is protected by a spinlock, but does not work if the
IRQ handler is protected by mutex, i.e. this works for KS8851 with
Parallel bus interface, but not for KS8851 with SPI bus interface.
Remove the BH manipulation and instead of calling netif_rx() inside
the IRQ handler code protected by the lock, queue all the received
SKBs in the IRQ handler into a queue first, and once the IRQ handler
exits the critical section protected by the lock, dequeue all the
queued SKBs and push them all into netif_rx(). At this point, it is
safe to trigger the net_rx_action() softirq, since the netif_rx()
call is outside of the lock that protects the IRQ handler.
Fixes: be0384bf59 ("net: ks8851: Handle softirqs at the end of IRQ thread to fix hang")
Tested-by: Ronald Wahl <ronald.wahl@raritan.com> # KS8851 SPI
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240502183436.117117-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a6380cb4c ]
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
See: https://github.com/raspberrypi/linux/issues/3850
See: https://github.com/raspberrypi/firmware/issues/1882
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Maarten Vanraes <maarten@rmail.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f778941913 ]
Ensure the inner IP header is part of skb's linear data before reading
its ECN bits. Otherwise we might read garbage.
One symptom is the system erroneously logging errors like
"vxlan: non-ECT from xxx.xxx.xxx.xxx with TOS=xxxx".
Similar bugs have been fixed in geneve, ip_tunnel and ip6_tunnel (see
commit 1ca1ba465e ("geneve: make sure to pull inner header in
geneve_rx()") for example). So let's reuse the same code structure for
consistency. Maybe we'll can add a common helper in the future.
Fixes: d342894c5d ("vxlan: virtual extensible lan")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/1239c8db54efec341dd6455c77e0380f58923a3c.1714495737.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9a61c2017 ]
The Topaz family (88E6141 and 88E6341) only support 256 Forwarding
Information Tables.
Fixes: a75961d0eb ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6341")
Fixes: 1558727a1c ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6141")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240429133832.9547-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9067eccdd7 ]
The selftest for the driver sends a dummy packet and checks if the
packet will be received properly as it should be. The regular TX path
and the selftest can use the same network queue so locking is required
and was missing in the selftest path. This was addressed in the commit
cited below.
Unfortunately locking the TX queue requires BH to be disabled which is
not the case in selftest path which is invoked in process context.
Lockdep should be complaining about this.
Use __netif_tx_lock_bh() for TX queue locking.
Fixes: c650e04898 ("cxgb4: Fix race between loopback and normal Tx path")
Reported-by: "John B. Wyatt IV" <jwyatt@redhat.com>
Closes: https://lore.kernel.org/all/Zic0ot5aGgR-V4Ks@thinkpad2021/
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240429091147.YWAaal4v@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f26f719a36 ]
When calling qede_parse_actions() then the
return code was only used for a non-zero check,
and then -EINVAL was returned.
qede_parse_actions() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit broke the implicit assumption
that only -EINVAL would ever be returned.
Only compile tested.
Fixes: 319a1d1947 ("flow_offload: check for basic action hw stats type")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27b44414a3 ]
In qede_flow_spec_to_rule(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced qede_flow_spec_to_rule(),
and this call to qede_parse_flow_attr(), it looks
like it just duplicated how it was already used.
Only compile tested.
Fixes: 37c5d3efd7 ("qede: use ethtool_rx_flow_rule() to remove duplicated parser code")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcee2065a1 ]
In qede_add_tc_flower_fltr(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced these functions.
Only compile tested.
Fixes: 2ce9c93eac ("qede: Ingress tc flower offload (drop action) support.")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25714466a ]
Explicitly set 'rc' (return code), before jumping to the
unlock and return path.
By not having any code depend on that 'rc' remains at
it's initial value of -EINVAL, then we can re-use 'rc' for
the return code of function calls in subsequent patches.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fcee2065a1 ("net: qede: use return from qede_parse_flow_attr() for flower")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f299ee709f ]
We try to access count + 1 byte from userspace with memdup_user(buffer,
count + 1). However, the userspace only provides buffer of count bytes and
only these count bytes are verified to be okay to access. To ensure the
copied buffer is NUL terminated, we use memdup_user_nul instead.
Fixes: 3a2eb515d1 ("octeontx2-af: Fix an off by one in rvu_dbg_qsize_write()")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-6-f1f1b53a10f4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c34096c7f ]
Currently, we allocate a nbytes-sized kernel buffer and copy nbytes from
userspace to that buffer. Later, we use sscanf on this buffer but we don't
ensure that the string is terminated inside the buffer, this can lead to
OOB read when using sscanf. Fix this issue by using memdup_user_nul
instead of memdup_user.
Fixes: 7afc5dbde0 ("bna: Add debugfs interface.")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-2-f1f1b53a10f4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 39d26a8f2e upstream.
mlx5 Rx flow steering and CQE handling enable the driver to be able to
update an skb's md_dst attribute as MACsec when MACsec traffic arrives when
a device is configured for offloading. Advertise this to the core stack to
take advantage of this capability.
Cc: stable@vger.kernel.org
Fixes: b7c9400cbc ("net/mlx5e: Implement MACsec Rx data path using MACsec skb_metadata_dst")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240423181319.115860-5-rrameshbabu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 642c984dd0 upstream.
Can now correctly identify where the packets should be delivered by using
md_dst or its absence on devices that provide it.
This detection is not possible without device drivers that update md_dst. A
fallback pattern should be used for supporting such device drivers. This
fallback mode causes multicast messages to be cloned to both the non-macsec
and macsec ports, independent of whether the multicast message received was
encrypted over MACsec or not. Other non-macsec traffic may also fail to be
handled correctly for devices in promiscuous mode.
Link: https://lore.kernel.org/netdev/ZULRxX9eIbFiVi7v@hog/
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: stable@vger.kernel.org
Fixes: 860ead89b8 ("net/macsec: Add MACsec skb_metadata_dst Rx Data path support")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240423181319.115860-4-rrameshbabu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3eb7dd47b upstream.
b44_free_rings() accesses b44::rx_buffers (and ::tx_buffers)
unconditionally, but b44::rx_buffers is only valid when the
device is up (they get allocated in b44_open(), and deallocated
again in b44_close()), any other time these are just a NULL pointers.
So if you try to change the pause params while the network interface
is disabled/administratively down, everything explodes (which likely
netifd tries to do).
Link: https://github.com/openwrt/openwrt/issues/13789
Fixes: 1da177e4c3 (Linux-2.6.12-rc2)
Cc: stable@vger.kernel.org
Reported-by: Peter Münster <pm@a16n.net>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Tested-by: Peter Münster <pm@a16n.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Peter Münster <pm@a16n.net>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/87y192oolj.fsf@a16n.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 059a49aa2e upstream.
There is a bug when setting the RSS options in virtio_net that can break
the whole machine, getting the kernel into an infinite loop.
Running the following command in any QEMU virtual machine with virtionet
will reproduce this problem:
# ethtool -X eth0 hfunc toeplitz
This is how the problem happens:
1) ethtool_set_rxfh() calls virtnet_set_rxfh()
2) virtnet_set_rxfh() calls virtnet_commit_rss_command()
3) virtnet_commit_rss_command() populates 4 entries for the rss
scatter-gather
4) Since the command above does not have a key, then the last
scatter-gatter entry will be zeroed, since rss_key_size == 0.
sg_buf_size = vi->rss_key_size;
5) This buffer is passed to qemu, but qemu is not happy with a buffer
with zero length, and do the following in virtqueue_map_desc() (QEMU
function):
if (!sz) {
virtio_error(vdev, "virtio: zero sized buffers are not allowed");
6) virtio_error() (also QEMU function) set the device as broken
vdev->broken = true;
7) Qemu bails out, and do not repond this crazy kernel.
8) The kernel is waiting for the response to come back (function
virtnet_send_command())
9) The kernel is waiting doing the following :
while (!virtqueue_get_buf(vi->cvq, &tmp) &&
!virtqueue_is_broken(vi->cvq))
cpu_relax();
10) None of the following functions above is true, thus, the kernel
loops here forever. Keeping in mind that virtqueue_is_broken() does
not look at the qemu `vdev->broken`, so, it never realizes that the
vitio is broken at QEMU side.
Fix it by not sending RSS commands if the feature is not available in
the device.
Fixes: c7114b1249 ("drivers/net/virtio_net: Added basic RSS support.")
Cc: stable@vger.kernel.org
Cc: qemu-devel@nongnu.org
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Konstantin Ovsepian <ovs@ovs.to>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b9e743e92 ]
The CPTS, by design, captures the messageType (Sync, Delay_Req, etc.)
field from the second nibble of the PTP header which is defined in the
PTPv2 (1588-2008) specification. In the PTPv1 (1588-2002) specification
the first two bytes of the PTP header are defined as the versionType
which is always 0x0001. This means that any PTPv1 packets that are
tagged for TX timestamping by the CPTS will have their messageType set
to 0x0 which corresponds to a Sync message type. This causes issues
when a PTPv1 stack is expecting a Delay_Req (messageType: 0x1)
timestamp that never appears.
Fix this by checking if the ptp_class of the timestamped TX packet is
PTP_CLASS_V1 and then matching the PTP sequence ID to the stored
sequence ID in the skb->cb data structure. If the sequence IDs match
and the packet is of type PTPv1 then there is a chance that the
messageType has been incorrectly stored by the CPTS so overwrite the
messageType stored by the CPTS with the messageType from the skb->cb
data structure. This allows the PTPv1 stack to receive TX timestamps
for Delay_Req packets which are necessary to lock onto a PTP Leader.
Signed-off-by: Jason Reeder <jreeder@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Ed Trexel <ed.trexel@hp.com>
Fixes: f6bd59526c ("net: ethernet: ti: introduce am654 common platform time sync driver")
Link: https://lore.kernel.org/r/20240424071626.32558-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54976cf58d ]
Same number of TCs doesn't imply that underlying TC configs are
same. The config could be different due to difference in number
of queues in each TC. Add utility function to determine if TC
configs are same.
Fixes: d5b33d0244 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Mineri Bhange <minerix.bhange@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240423182723.740401-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef3c313119 ]
If the MFS is set below the default (0x2600), a warning message is
reported like the following :
MFS for port 1 has been set below the default: 600
This message is a bit confusing as the number shown here (600) is in
fact an hexa number: 0x600 = 1536
Without any explicit "0x" prefix, this message is read like the MFS is
set to 600 bytes.
MFS, as per MTUs, are usually expressed in decimal base.
This commit reports both current and default MFS values in decimal
so it's less confusing for end-users.
A typical warning message looks like the following :
MFS for port 1 (1536) has been set below the default (9728)
Signed-off-by: Erwan Velu <e.velu@criteo.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixes: 3a2c6ced90 ("i40e: Add a check to see if MFS is set")
Link: https://lore.kernel.org/r/20240423182723.740401-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7301177307 ]
I added OOM and netpoll discard counters, naively assuming that
the cpr pointer is pointing to a common completion ring.
Turns out that is usually *a* completion ring but not *the*
completion ring which bnapi->cp_ring points to. bnapi->cp_ring
is where the stats are read from, so we end up reporting 0
thru ethtool -S and qstat even though the drop events have happened.
Make 100% sure we're recording statistics in the correct structure.
Fixes: 907fd4a294 ("bnxt: count discards due to memory allocation errors")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240424002148.3937059-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb4e2b70a7 ]
The rehash delayed work is rescheduled with a delay if the number of
credits at end of the work is not negative as supposedly it means that
the migration ended. Otherwise, it is rescheduled immediately.
After "mlxsw: spectrum_acl_tcam: Fix possible use-after-free during
rehash" the above is no longer accurate as a non-negative number of
credits is no longer indicative of the migration being done. It can also
happen if the work encountered an error in which case the migration will
resume the next time the work is scheduled.
The significance of the above is that it is possible for the work to be
pending and associated with hints that were allocated when the migration
started. This leads to the hints being leaked [1] when the work is
canceled while pending as part of ACL region dismantle.
Fix by freeing the hints if hints are associated with a work that was
canceled while pending.
Blame the original commit since the reliance on not having a pending
work associated with hints is fragile.
[1]
unreferenced object 0xffff88810e7c3000 (size 256):
comm "kworker/0:16", pid 176, jiffies 4295460353
hex dump (first 32 bytes):
00 30 95 11 81 88 ff ff 61 00 00 00 00 00 00 80 .0......a.......
00 00 61 00 40 00 00 00 00 00 00 00 04 00 00 00 ..a.@...........
backtrace (crc 2544ddb9):
[<00000000cf8cfab3>] kmalloc_trace+0x23f/0x2a0
[<000000004d9a1ad9>] objagg_hints_get+0x42/0x390
[<000000000b143cf3>] mlxsw_sp_acl_erp_rehash_hints_get+0xca/0x400
[<0000000059bdb60a>] mlxsw_sp_acl_tcam_vregion_rehash_work+0x868/0x1160
[<00000000e81fd734>] process_one_work+0x59c/0xf20
[<00000000ceee9e81>] worker_thread+0x799/0x12c0
[<00000000bda6fe39>] kthread+0x246/0x300
[<0000000070056d23>] ret_from_fork+0x34/0x70
[<00000000dea2b93e>] ret_from_fork_asm+0x1a/0x30
Fixes: c9c9af91f1 ("mlxsw: spectrum_acl: Allow to interrupt/continue rehash work")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/0cc12ebb07c4d4c41a1265ee2c28b392ff997a86.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b377add0f0 ]
Both the function that migrates all the chunks within a region and the
function that migrates all the entries within a chunk call
list_first_entry() on the respective lists without checking that the
lists are not empty. This is incorrect usage of the API, which leads to
the following warning [1].
Fix by returning if the lists are empty as there is nothing to migrate
in this case.
[1]
WARNING: CPU: 0 PID: 6437 at drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c:1266 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0>
Modules linked in:
CPU: 0 PID: 6437 Comm: kworker/0:37 Not tainted 6.9.0-rc3-custom-00883-g94a65f079ef6 #39
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0x2c0
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x4a0
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 6f9579d4e3 ("mlxsw: spectrum_acl: Remember where to continue rehash migration")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/4628e9a22d1d84818e28310abbbc498e7bc31bc9.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 743edc8547 ]
As previously explained, the rehash delayed work migrates filters from
one region to another. This is done by iterating over all chunks (all
the filters with the same priority) in the region and in each chunk
iterating over all the filters.
When the work runs out of credits it stores the current chunk and entry
as markers in the per-work context so that it would know where to resume
the migration from the next time the work is scheduled.
Upon error, the chunk marker is reset to NULL, but without resetting the
entry markers despite being relative to it. This can result in migration
being resumed from an entry that does not belong to the chunk being
migrated. In turn, this will eventually lead to a chunk being iterated
over as if it is an entry. Because of how the two structures happen to
be defined, this does not lead to KASAN splats, but to warnings such as
[1].
Fix by creating a helper that resets all the markers and call it from
all the places the currently only reset the chunk marker. For good
measures also call it when starting a completely new rehash. Add a
warning to avoid future cases.
[1]
WARNING: CPU: 7 PID: 1076 at drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_keys.c:407 mlxsw_afk_encode+0x242/0x2f0
Modules linked in:
CPU: 7 PID: 1076 Comm: kworker/7:24 Tainted: G W 6.9.0-rc3-custom-00880-g29e61d91b77b #29
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:mlxsw_afk_encode+0x242/0x2f0
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_atcam_entry_add+0xd9/0x3c0
mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x109/0x290
mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x470
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
</TASK>
Fixes: 6f9579d4e3 ("mlxsw: spectrum_acl: Remember where to continue rehash migration")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/cc17eed86b41dd829d39b07906fec074a9ce580e.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ca3f7a7b6 ]
The rehash delayed work migrates filters from one region to another.
This is done by iterating over all chunks (all the filters with the same
priority) in the region and in each chunk iterating over all the
filters.
If the migration fails, the code tries to migrate the filters back to
the old region. However, the rollback itself can also fail in which case
another migration will be erroneously performed. Besides the fact that
this ping pong is not a very good idea, it also creates a problem.
Each virtual chunk references two chunks: The currently used one
('vchunk->chunk') and a backup ('vchunk->chunk2'). During migration the
first holds the chunk we want to migrate filters to and the second holds
the chunk we are migrating filters from.
The code currently assumes - but does not verify - that the backup chunk
does not exist (NULL) if the currently used chunk does not reference the
target region. This assumption breaks when we are trying to rollback a
rollback, resulting in the backup chunk being overwritten and leaked
[1].
Fix by not rolling back a failed rollback and add a warning to avoid
future cases.
[1]
WARNING: CPU: 5 PID: 1063 at lib/parman.c:291 parman_destroy+0x17/0x20
Modules linked in:
CPU: 5 PID: 1063 Comm: kworker/5:11 Tainted: G W 6.9.0-rc2-custom-00784-gc6a05c468a0b #14
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:parman_destroy+0x17/0x20
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_atcam_region_fini+0x19/0x60
mlxsw_sp_acl_tcam_region_destroy+0x49/0xf0
mlxsw_sp_acl_tcam_vregion_rehash_work+0x1f1/0x470
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 8435005185 ("mlxsw: spectrum_acl: Do rollback as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/d5edd4f4503934186ae5cfe268503b16345b4e0f.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bcf925587 ]
In the rare cases when the device resources are exhausted it is likely
that the rehash delayed work will fail. An error message will be printed
whenever this happens which can be overwhelming considering the fact
that the work is per-region and that there can be hundreds of regions.
Fix by rate limiting the error message.
Fixes: e5e7962ee5 ("mlxsw: spectrum_acl: Implement region migration according to hints")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/c510763b2ebd25e7990d80183feff91cde593145.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5422598888 ]
The rehash delayed work migrates filters from one region to another
according to the number of available credits.
The migrated from region is destroyed at the end of the work if the
number of credits is non-negative as the assumption is that this is
indicative of migration being complete. This assumption is incorrect as
a non-negative number of credits can also be the result of a failed
migration.
The destruction of a region that still has filters referencing it can
result in a use-after-free [1].
Fix by not destroying the region if migration failed.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_ctcam_region_entry_remove+0x21d/0x230
Read of size 8 at addr ffff8881735319e8 by task kworker/0:31/3858
CPU: 0 PID: 3858 Comm: kworker/0:31 Tainted: G W 6.9.0-rc2-custom-00782-gf2275c2157d8 #5
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_acl_ctcam_region_entry_remove+0x21d/0x230
mlxsw_sp_acl_ctcam_entry_del+0x2e/0x70
mlxsw_sp_acl_atcam_entry_del+0x81/0x210
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x3cd/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 174:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
__kmalloc+0x19c/0x360
mlxsw_sp_acl_tcam_region_create+0xdf/0x9c0
mlxsw_sp_acl_tcam_vregion_rehash_work+0x954/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Freed by task 7:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x102/0x170
__kasan_slab_free+0x14/0x30
kfree+0xc1/0x290
mlxsw_sp_acl_tcam_region_destroy+0x272/0x310
mlxsw_sp_acl_tcam_vregion_rehash_work+0x731/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Fixes: c9c9af91f1 ("mlxsw: spectrum_acl: Allow to interrupt/continue rehash work")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/3e412b5659ec2310c5c615760dfe5eac18dd7ebd.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79b5b4b18b ]
The rule activity update delayed work periodically traverses the list of
configured rules and queries their activity from the device.
As part of this task it accesses the entry pointed by 'ventry->entry',
but this entry can be changed concurrently by the rehash delayed work,
leading to a use-after-free [1].
Fix by closing the race and perform the activity query under the
'vregion->lock' mutex.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_tcam_flower_rule_activity_get+0x121/0x140
Read of size 8 at addr ffff8881054ed808 by task kworker/0:18/181
CPU: 0 PID: 181 Comm: kworker/0:18 Not tainted 6.9.0-rc2-custom-00781-gd5ab772d32f7 #2
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_acl_tcam_flower_rule_activity_get+0x121/0x140
mlxsw_sp_acl_rule_activity_update_work+0x219/0x400
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 1039:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
__kmalloc+0x19c/0x360
mlxsw_sp_acl_tcam_entry_create+0x7b/0x1f0
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x30d/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Freed by task 1039:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x102/0x170
__kasan_slab_free+0x14/0x30
kfree+0xc1/0x290
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x3d7/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Fixes: 2bffc5322f ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1fcce0a60b231ebeb2515d91022284ba7b4ffe7a.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d90cfe2056 ]
The purpose of the rehash delayed work is to reduce the number of masks
(eRPs) used by an ACL region as the eRP bank is a global and limited
resource.
This is done in three steps:
1. Creating a new set of masks and a new ACL region which will use the
new masks and to which the existing filters will be migrated to. The
new region is assigned to 'vregion->region' and the region from which
the filters are migrated from is assigned to 'vregion->region2'.
2. Migrating all the filters from the old region to the new region.
3. Destroying the old region and setting 'vregion->region2' to NULL.
Only the second steps is performed under the 'vregion->lock' mutex
although its comments says that among other things it "Protects
consistency of region, region2 pointers".
This is problematic as the first step can race with filter insertion
from user space that uses 'vregion->region', but under the mutex.
Fix by holding the mutex across the entirety of the delayed work and not
only during the second step.
Fixes: 2bffc5322f ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1ec1d54edf2bad0a369e6b4fa030aba64e1f124b.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2a904107e ]
Since call_rcu, which is called in the hlist_for_each_entry_rcu traversal
of gtp_dellink, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 94dc550a50 ("gtp: fix an use-after-free in ipv4_pdp_find()")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ce62d5b2f ]
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize overide.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c611723 ("net: cdc_ncm: reduce skb truesize
in rx path")
Fixes: f8ebb3ac88 ("net: usb: ax88179_178a: Fix packet receiving")
Reported-by: shironeko <shironeko@tesaguri.club>
Closes: https://lore.kernel.org/netdev/c110f41a0d2776b525930f213ca9715c@tesaguri.club/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jose Alonso <joalonsof@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240421193828.1966195-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1acdc226b ]
We do not support two simultaneous recoveries so check for reset
flag, BNXT_STATE_IN_FW_RESET, and do not proceed with AER further.
When the pci channel state is pci_channel_io_frozen, the PCIe link
can not be trusted so we disable the traffic immediately and stop
BAR access by calling bnxt_fw_fatal_close(). BAR access after
AER fatal error can cause an NMI.
Fixes: f75d9a0aa9 ("bnxt_en: Re-write PCI BARs after PCI fatal error.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7474b1c82b ]
Introduce bnxt_fw_fatal_close() API which can be used
to stop data path and disable device when firmware
is in fatal state.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: a1acdc226b ("bnxt_en: Fix the PCI-AER routines")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 976c44af48 ]
The device's manual (PRM - Programmer's Reference Manual) classifies the
trap that is used to deliver EMAD responses as an "event trap". Among
other things, it means that the only actions that can be associated with
the trap are TRAP and FORWARD (NOP).
Currently, during driver de-initialization the driver unregisters the
trap by setting its action to DISCARD, which violates the above
guideline. Future firmware versions will prevent such misuses by
returning an error. This does not prevent the driver from working, but
an error will be printed to the kernel log during module removal /
devlink reload:
mlxsw_spectrum 0000:03:00.0: Reg cmd access status failed (status=7(bad parameter))
mlxsw_spectrum 0000:03:00.0: Reg cmd access failed (reg_id=7003(hpkt),type=write)
Suppress the error message by aligning the driver to the manual and use
a FORWARD (NOP) action when unregistering the trap.
Fixes: 4ec14b7634 ("mlxsw: Add interface to access registers and process events")
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/753a89e14008fde08cb4a2c1e5f537b81d8eb2d6.1713446092.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f58f45c1e5 ]
The VXLAN driver currently does not check if the inner layer2
source-address is valid.
In case source-address snooping/learning is enabled, a entry in the FDB
for the invalid address is created with the layer3 address of the tunnel
endpoint.
If the frame happens to have a non-unicast address set, all this
non-unicast traffic is subsequently not flooded to the tunnel network
but sent to the learnt host in the FDB. To make matters worse, this FDB
entry does not expire.
Apply the same filtering for packets as it is done for bridges. This not
only drops these invalid packets but avoids them from being learnt into
the FDB.
Fixes: d342894c5d ("vxlan: virtual extensible lan")
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bada85a3f5 ]
This function is supposed to return a uid on success, and an errno in
failure.
But it currently returns the return value of the specific cmd version
handler, which in turn returns 0 on success and errno otherwise.
This means that on success, iwl_mvm_build_scan_cmd will return 0
regardless if the actual uid.
Fix this by returning the uid if the handler succeeded.
Fixes: 687db6ff5b ("iwlwifi: scan: make new scan req versioning flow")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://msgid.link/20240415114847.5e2d602b3190.I4c4931021be74a67a869384c8f8ee7463e0c7857@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbfff5bf92 ]
If a PASN station is added, and an old PASN station already exists
for the same mac address, remove the old station before adding the
new one. Keeping the old station caueses old security context to
be used in measurements.
Fixes: 0739a7d70e ("iwlwifi: mvm: initiator: add option for adding a PASN responder")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415114847.ef3544a416f2.I4e8c7c8ca22737f4f908ae5cd4fc0b920c703dd3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 06dfcd4098 upstream.
The commit 40b5d2f15c ("net: dsa: mt7530: Add support for EEE features")
brought EEE support but did not enable EEE on MT7531 switch MACs. EEE is
enabled on MT7531 switch MACs by pulling the LAN2LED0 pin low on the board
(bootstrapping), unsetting the EEE_DIS bit on the trap register, or setting
the internal EEE switch bit on the CORE_PLL_GROUP4 register. Thanks to
SkyLake Huang (黃啟澤) from MediaTek for providing information on the
internal EEE switch bit.
There are existing boards that were not designed to pull the pin low.
Because of that, the EEE status currently depends on the board design.
The EEE_DIS bit on the trap pertains to the LAN2LED0 pin which is usually
used to control an LED. Once the bit is unset, the pin will be low. That
will make the active low LED turn on. The pin is controlled by the switch
PHY. It seems that the PHY controls the pin in the way that it inverts the
pin state. That means depending on the wiring of the LED connected to
LAN2LED0 on the board, the LED may be on without an active link.
To not cause this unwanted behaviour whilst enabling EEE on all boards, set
the internal EEE switch bit on the CORE_PLL_GROUP4 register.
My testing on MT7531 shows a certain amount of traffic loss when EEE is
enabled. That said, I haven't come across a board that enables EEE. So
enable EEE on the switch MACs but disable EEE advertisement on the switch
PHYs. This way, we don't change the behaviour of the majority of the boards
that have this switch. The mediatek-ge PHY driver already disables EEE
advertisement on the switch PHYs but my testing shows that it is somehow
enabled afterwards. Disabling EEE advertisement before the PHY driver
initialises keeps it off.
With this change, EEE can now be enabled using ethtool.
Fixes: 40b5d2f15c ("net: dsa: mt7530: Add support for EEE features")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240408-for-net-mt7530-fix-eee-for-mt7531-mt7988-v3-1-84fdef1f008b@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f563c31ff upstream.
The MT7530 switch after reset initialises with a core clock frequency that
works with a 25MHz XTAL connected to it. For 40MHz XTAL, the core clock
frequency must be set to 500MHz.
The mt7530_pll_setup() function is responsible of setting the core clock
frequency. Currently, it runs on MT7530 with 25MHz and 40MHz XTAL. This
causes MT7530 switch with 25MHz XTAL to egress and ingress frames
improperly.
Introduce a check to run it only on MT7530 with 40MHz XTAL.
The core clock frequency is set by writing to a switch PHY's register.
Access to the PHY's register is done via the MDIO bus the switch is also
on. Therefore, it works only when the switch makes switch PHYs listen on
the MDIO bus the switch is on. This is controlled either by the state of
the ESW_P1_LED_1 pin after reset deassertion or modifying bit 5 of the
modifiable trap register.
When ESW_P1_LED_1 is pulled high, PHY indirect access is used. That means
accessing PHY registers via the PHY indirect access control register of the
switch.
When ESW_P1_LED_1 is pulled low, PHY direct access is used. That means
accessing PHY registers via the MDIO bus the switch is on.
For MT7530 switch with 40MHz XTAL on a board with ESW_P1_LED_1 pulled high,
the core clock frequency won't be set to 500MHz, causing the switch to
egress and ingress frames improperly.
Run mt7530_pll_setup() after PHY direct access is set on the modifiable
trap register.
With these two changes, all MT7530 switches with 25MHz and 40MHz, and
P1_LED_1 pulled high or low, will egress and ingress frames properly.
Link: 4a5dd143f2/linux-mt/drivers/net/ethernet/mediatek/gsw_mt7623.c (L1039)
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240320-for-net-mt7530-fix-25mhz-xtal-with-direct-phy-access-v1-1-d92f605f1160@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
